Age | Commit message (Collapse) | Author | Files | Lines |
|
Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.
Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64e269 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.
That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.
Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.
Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().
However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.
In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.
Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.
Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.
For example, let's consider the following scenario on a system
with HZ=1000:
* The synflood timestamp is 0, either because that's the timestamp
of the last synflood or, more commonly, because we're working with
a freshly created socket.
* We receive a new SYN, which triggers synflood protection. Let's say
that this happens when jiffies == 2147484649 (that is,
'synflood timestamp' + HZ + 2^31 + 1).
* Then tcp_synq_overflow() doesn't update the synflood timestamp,
because time_after32(2147484649, 1000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 1000: the value of 'last_overflow' + HZ.
* A bit later, we receive the ACK completing the 3WHS. But
cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
says that we're not under synflood. That's because
time_after32(2147484649, 120000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.
Of course, in reality jiffies would have increased a bit, but this
condition will last for the next 119 seconds, which is far enough
to accommodate for jiffie's growth.
Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.
Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.
Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.
For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit
cca9bab1b72c ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.
Fixes: cca9bab1b72c ("tcp: use monotonic timestamps for PAWS")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may have found a bug in the nxp/lpc_eth.c driver. The function
platform_set_drvdata() is called twice, the second time it is called,
in lpc_mii_init(), it overwrites the struct net_device which should be
at pdev->dev->driver_data with pldat->mii_bus. When trying to remove
the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will
return the pldat->mii_bus pointer and try to use it as a struct
net_device pointer. This causes unregister_netdev to segfault and
generate a kernel BUG. Is this reproducible?
Signed-off-by: Daniel Martinez <linux@danielsmartinez.com>
Signed-off-by: Bruno Carneiro da Cunha <brunocarneirodacunha@usp.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Back in 2008, Adam Langley fixed the corner case of packets for flows
having all of the following options : MD5 TS SACK
Since MD5 needs 20 bytes, and TS needs 12 bytes, no sack block
can be cooked from the remaining 8 bytes.
tcp_established_options() correctly sets opts->num_sack_blocks
to zero, but returns 36 instead of 32.
This means TCP cooks packets with 4 extra bytes at the end
of options, containing unitialized bytes.
Fixes: 33ad798c924b ("tcp: options clean up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a device is bound to a clsact qdisc, bind events are triggered to
registered drivers for both ingress and egress. However, if a driver
registers to such a device using the indirect block routines then it is
assumed that it is only interested in ingress offload and so only replays
ingress bind/unbind messages.
The NFP driver supports the offload of some egress filters when
registering to a block with qdisc of type clsact. However, on unregister,
if the block is still active, it will not receive an unbind egress
notification which can prevent proper cleanup of other registered
callbacks.
Modify the indirect block callback command in TC to send messages of
ingress and/or egress bind depending on the qdisc in use. NFP currently
supports egress offload for TC flower offload so the changes are only
added to TC.
Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.
When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.
Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.
Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dev_hold has to be called always in netdev_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.
Fixes: b8eb718348b8 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Reported-by: Hulk Robot <hulkci@huawei.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 43e665287f93 ("net-next: dsa: fix flow dissection") added an
ability to override protocol and network offset during flow dissection
for DSA-enabled devices (i.e. controllers shipped as switch CPU ports)
in order to fix skb hashing for RPS on Rx path.
However, skb_hash() and added part of code can be invoked not only on
Rx, but also on Tx path if we have a multi-queued device and:
- kernel is running on UP system or
- XPS is not configured.
The call stack in this two cases will be like: dev_queue_xmit() ->
__dev_queue_xmit() -> netdev_core_pick_tx() -> netdev_pick_tx() ->
skb_tx_hash() -> skb_get_hash().
The problem is that skbs queued for Tx have both network offset and
correct protocol already set up even after inserting a CPU tag by DSA
tagger, so calling tag_ops->flow_dissect() on this path actually only
breaks flow dissection and hashing.
This can be observed by adding debug prints just before and right after
tag_ops->flow_dissect() call to the related block of code:
Before the patch:
Rx path (RPS):
[ 19.240001] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 19.244271] tag_ops->flow_dissect()
[ 19.247811] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */
[ 19.215435] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 19.219746] tag_ops->flow_dissect()
[ 19.223241] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */
[ 18.654057] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 18.658332] tag_ops->flow_dissect()
[ 18.661826] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */
Tx path (UP system):
[ 18.759560] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */
[ 18.763933] tag_ops->flow_dissect()
[ 18.767485] Tx: proto: 0x920b, nhoff: 34 /* junk */
[ 22.800020] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */
[ 22.804392] tag_ops->flow_dissect()
[ 22.807921] Tx: proto: 0x920b, nhoff: 34 /* junk */
[ 16.898342] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */
[ 16.902705] tag_ops->flow_dissect()
[ 16.906227] Tx: proto: 0x920b, nhoff: 34 /* junk */
After:
Rx path (RPS):
[ 16.520993] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 16.525260] tag_ops->flow_dissect()
[ 16.528808] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */
[ 15.484807] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 15.490417] tag_ops->flow_dissect()
[ 15.495223] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */
[ 17.134621] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[ 17.138895] tag_ops->flow_dissect()
[ 17.142388] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */
Tx path (UP system):
[ 15.499558] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */
[ 20.664689] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */
[ 18.565782] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */
In order to fix that we can add the check 'proto == htons(ETH_P_XDSA)'
to prevent code from calling tag_ops->flow_dissect() on Tx.
I also decided to initialize 'offset' variable so tagger callbacks can
now safely leave it untouched without provoking a chaos.
Fixes: 43e665287f93 ("net-next: dsa: fix flow dissection")
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ENOTSUPP is not available in userspace, for example:
setsockopt failed, 524, Unknown error 524
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the iteration end check in fuse_dev_splice_write(). The iterator
position can only be compared with == or != since wrappage may be involved.
Fixes: 8cefc107ca54 ("pipe: Use head and tail pointers for the ring, not cursor and length")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Similarly to commit 8f868d68d335 ("pipe: Fix missing mask update after
pipe_wait()") this fixes a case where the pipe rewrite ended up caching
the pipe state incorrectly over a pipe lock drop event.
It wasn't quite as obvious, because you needed to splice data from a
pipe to a file, which is a fairly unusual operation, but it's completely
wrong.
Make sure we load the pipe head/tail/size information only after we've
waited for there to be data in the pipe.
While in that file, also make one of the splice helper functions use the
canonical arghument order for pipe_empty(). That's syntactic - pipe
emptiness is just that head and tail are equal, and thus mixing up head
and tail doesn't really matter. It's still wrong, though.
Reported-by: David Sterba <dsterba@suse.cz>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When using the special SID to store the mode bits in an ACE (See
http://technet.microsoft.com/en-us/library/hh509017(v=ws.10).aspx)
which is enabled with mount parm "modefromsid" we were not
passing in the mode via SMB3 create (although chmod was enabled).
SMB3 create allows a security descriptor context to be passed
in (which is more atomic and thus preferable to setting the mode
bits after create via a setinfo).
This patch enables setting the mode bits on create when using
modefromsid mount option. In addition it fixes an endian
error in the definition of the Control field flags in the SMB3
security descriptor. It also makes the ACE type of the special
SID better match the documentation (and behavior of servers
which use this to store mode bits in SMB3 ACLs).
Signed-off-by: Steve French <stfrench@microsoft.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
CONFIG_RETPOLINE=y made indirect calls expensive.
gcc seems to add an indirect call in ____sys_recvmsg().
Rewriting the code slightly makes sure to avoid this indirection.
Alternative would be to not call sock_recvmsg() and instead
use security_socket_recvmsg() and sock_recvmsg_nosec(),
but this is less readable IMO.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to set/get/dump, the tipc uses the generic netlink
infrastructure. So, when tipc module is inserted, init function
calls genl_register_family().
After genl_register_family(), set/get/dump commands are immediately
allowed and these callbacks internally use the net_generic.
net_generic is allocated by register_pernet_device() but this
is called after genl_register_family() in the __init function.
So, these callbacks would use un-initialized net_generic.
Test commands:
#SHELL1
while :
do
modprobe tipc
modprobe -rv tipc
done
#SHELL2
while :
do
tipc link list
done
Splat looks like:
[ 59.616322][ T2788] kasan: CONFIG_KASAN_INLINE enabled
[ 59.617234][ T2788] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 59.618398][ T2788] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 59.619389][ T2788] CPU: 3 PID: 2788 Comm: tipc Not tainted 5.4.0+ #194
[ 59.620231][ T2788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 59.621428][ T2788] RIP: 0010:tipc_bcast_get_broadcast_mode+0x131/0x310 [tipc]
[ 59.622379][ T2788] Code: c7 c6 ef 8b 38 c0 65 ff 0d 84 83 c9 3f e8 d7 a5 f2 e3 48 8d bb 38 11 00 00 48 b8 00 00 00 00
[ 59.622550][ T2780] NET: Registered protocol family 30
[ 59.624627][ T2788] RSP: 0018:ffff88804b09f578 EFLAGS: 00010202
[ 59.624630][ T2788] RAX: dffffc0000000000 RBX: 0000000000000011 RCX: 000000008bc66907
[ 59.624631][ T2788] RDX: 0000000000000229 RSI: 000000004b3cf4cc RDI: 0000000000001149
[ 59.624633][ T2788] RBP: ffff88804b09f588 R08: 0000000000000003 R09: fffffbfff4fb3df1
[ 59.624635][ T2788] R10: fffffbfff50318f8 R11: ffff888066cadc18 R12: ffffffffa6cc2f40
[ 59.624637][ T2788] R13: 1ffff11009613eba R14: ffff8880662e9328 R15: ffff8880662e9328
[ 59.624639][ T2788] FS: 00007f57d8f7b740(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000
[ 59.624645][ T2788] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 59.625875][ T2780] tipc: Started in single node mode
[ 59.626128][ T2788] CR2: 00007f57d887a8c0 CR3: 000000004b140002 CR4: 00000000000606e0
[ 59.633991][ T2788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 59.635195][ T2788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 59.636478][ T2788] Call Trace:
[ 59.637025][ T2788] tipc_nl_add_bc_link+0x179/0x1470 [tipc]
[ 59.638219][ T2788] ? lock_downgrade+0x6e0/0x6e0
[ 59.638923][ T2788] ? __tipc_nl_add_link+0xf90/0xf90 [tipc]
[ 59.639533][ T2788] ? tipc_nl_node_dump_link+0x318/0xa50 [tipc]
[ 59.640160][ T2788] ? mutex_lock_io_nested+0x1380/0x1380
[ 59.640746][ T2788] tipc_nl_node_dump_link+0x4fd/0xa50 [tipc]
[ 59.641356][ T2788] ? tipc_nl_node_reset_link_stats+0x340/0x340 [tipc]
[ 59.642088][ T2788] ? __skb_ext_del+0x270/0x270
[ 59.642594][ T2788] genl_lock_dumpit+0x85/0xb0
[ 59.643050][ T2788] netlink_dump+0x49c/0xed0
[ 59.643529][ T2788] ? __netlink_sendskb+0xc0/0xc0
[ 59.644044][ T2788] ? __netlink_dump_start+0x190/0x800
[ 59.644617][ T2788] ? __mutex_unlock_slowpath+0xd0/0x670
[ 59.645177][ T2788] __netlink_dump_start+0x5a0/0x800
[ 59.645692][ T2788] genl_rcv_msg+0xa75/0xe90
[ 59.646144][ T2788] ? __lock_acquire+0xdfe/0x3de0
[ 59.646692][ T2788] ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[ 59.647340][ T2788] ? genl_lock_dumpit+0xb0/0xb0
[ 59.647821][ T2788] ? genl_unlock+0x20/0x20
[ 59.648290][ T2788] ? genl_parallel_done+0xe0/0xe0
[ 59.648787][ T2788] ? find_held_lock+0x39/0x1d0
[ 59.649276][ T2788] ? genl_rcv+0x15/0x40
[ 59.649722][ T2788] ? lock_contended+0xcd0/0xcd0
[ 59.650296][ T2788] netlink_rcv_skb+0x121/0x350
[ 59.650828][ T2788] ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[ 59.651491][ T2788] ? netlink_ack+0x940/0x940
[ 59.651953][ T2788] ? lock_acquire+0x164/0x3b0
[ 59.652449][ T2788] genl_rcv+0x24/0x40
[ 59.652841][ T2788] netlink_unicast+0x421/0x600
[ ... ]
Fixes: 7e4369057806 ("tipc: fix a slab object leak")
Fixes: a62fbccecd62 ("tipc: make subscriber server support net namespace")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When user runs a command like
tc qdisc add dev eth1 root mqprio
KASAN stack-out-of-bounds warning is emitted.
Currently, NLA_ALIGN macro used in mqprio_dump provides too large
buffer size as argument for nla_put and memcpy down the call stack.
The flow looks like this:
1. nla_put expects exact object size as an argument;
2. Later it provides this size to memcpy;
3. To calculate correct padding for SKB, nla_put applies NLA_ALIGN
macro itself.
Therefore, NLA_ALIGN should not be applied to the nla_put parameter.
Otherwise it will lead to out-of-bounds memory access in memcpy.
Fixes: 4e8b86c06269 ("mqprio: Introduce new hardware offload mode and shaper in mqprio")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refer to the databook of DesignWare Cores Ethernet MAC Universal:
6.2.1.5 Register 4 (Transmit Descriptor List Address Register
If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.
The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit fd7d58f0dbc3 ("ARM: multi_v7_defconfig: renormalize based on recent
additions") removed explicit enable line for CONFIG_DEBUG_FS, because
that feature has been selected by other enabled options: CONFIG_TRACING,
which were enabled by CONFIG_PERF_EVENTS.
In meantime, commit 0e4a459f56c3 ("tracing: Remove unnecessary DEBUG_FS
dependency") removed the dependency between CONFIG_DEBUG_FS and
CONFIG_TRACING, so CONFIG_DEBUG_FS is no longer enabled in default builds.
Enable it again explicitly, as debugfs support is essential for various
automated testing tools.
Link: https://lore.kernel.org/r/20191206125112.11006-1-m.szyprowski@samsung.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Stack overflow checking can be done by testing sp & (1 << THREAD_SHIFT)
only for the stacks are aligned to (2 << THREAD_SHIFT) with size of
(1 << THREAD_SIZE), and this is the case when CONFIG_VMAP_STACK is set.
Fix the code comment to avoid confusion.
Cc: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
[catalin.marinas@arm.com: Updated comment following Mark's suggestion]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When I tweaked the ftrace entry assembly in commit:
3b23e4991fb66f6d ("arm64: implement ftrace with regs")
... my ifdeffery tweaks left ftrace_graph_caller undefined for
CONFIG_DYNAMIC_FTRACE && CONFIG_FUNCTION_GRAPH_TRACER when ftrace is
based on mcount.
The kbuild test robot reported that this issue is detected at link time:
| arch/arm64/kernel/entry-ftrace.o: In function `skip_ftrace_call':
| arch/arm64/kernel/entry-ftrace.S:238: undefined reference to `ftrace_graph_caller'
| arch/arm64/kernel/entry-ftrace.S:238:(.text+0x3c): relocation truncated to fit: R_AARCH64_CONDBR19 against undefined symbol
| `ftrace_graph_caller'
| arch/arm64/kernel/entry-ftrace.S:243: undefined reference to `ftrace_graph_caller'
| arch/arm64/kernel/entry-ftrace.S:243:(.text+0x54): relocation truncated to fit: R_AARCH64_CONDBR19 against undefined symbol
| `ftrace_graph_caller'
This patch fixes the ifdeffery so that the mcount version of
ftrace_graph_caller doesn't depend on CONFIG_DYNAMIC_FTRACE. At the same
time, a redundant #else is removed from the ifdeffery for the
patchable-function-entry version of ftrace_graph_caller.
Fixes: 3b23e4991fb66f6d ("arm64: implement ftrace with regs")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Torsten Duwe <duwe@lst.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
compute_layout() is invoked as part of an alternative fixup under
stop_machine(). This function invokes get_random_long() which acquires a
sleeping lock on -RT which can not be acquired in this context.
Rename compute_layout() to kvm_compute_layout() and invoke it before
stop_machine() applies the alternatives. Add a __init prefix to
kvm_compute_layout() because the caller has it, too (and so the code can be
discarded after boot).
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
__range_ok(), invoked from access_ok(), clears the tag of the user
address only if CONFIG_ARM64_TAGGED_ADDR_ABI is enabled and the thread
opted in to the relaxed ABI. The latter sets the TIF_TAGGED_ADDR thread
flag. In the case of asynchronous I/O (e.g. io_submit()), the
access_ok() may be called from a kernel thread. Since kernel threads
don't have TIF_TAGGED_ADDR set, access_ok() will fail for valid tagged
user addresses. Example from the ffs_user_copy_worker() thread:
use_mm(io_data->mm);
ret = ffs_copy_to_iter(io_data->buf, ret, &io_data->data);
unuse_mm(io_data->mm);
Relax the __range_ok() check to always untag the user address if called
in the context of a kernel thread. The user pointers would have already
been checked via aio_setup_rw() -> import_{single_range,iovec}() at the
time of the asynchronous I/O request.
Fixes: 63f0c6037965 ("arm64: Introduce prctl() options to control the tagged user addresses ABI")
Cc: <stable@vger.kernel.org> # 5.4.x-
Cc: Will Deacon <will@kernel.org>
Reported-by: Evgenii Stepanov <eugenis@google.com>
Tested-by: Evgenii Stepanov <eugenis@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
__arch_get_hw_counter() should check clock_mode to see if it can access
CNTVCT. With the conversion to unified vDSO this check has been left out.
This causes on imx v6 and v7 (imx_v6_v7_defconfig) and other platforms to
hang at boot during the execution of the init process as per below:
[ 19.976852] Run /sbin/init as init process
[ 20.044931] Kernel panic - not syncing: Attempted to kill init!
exitcode=0x00000004
Fix the problem verifying that clock_mode is set coherently before
accessing CNTVCT.
Investigated-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Commit ca74b316df96 ("arm: Use common cpu_topology structure and
functions.") changed cpu_coregroup_mask() from the ARM32 specific
implementation in arch/arm/include/asm/topology.h to the one shared
with ARM64 and RISCV in drivers/base/arch_topology.c.
Currently on ARM32 (TC2 w/ CONFIG_SCHED_MC) the task scheduler setup
code (w/ CONFIG_SCHED_DEBUG) shows this during CPU hotplug:
ERROR: groups don't span domain->span
It happens to CPUs of the cluster of the CPU which gets hot-plugged
out on scheduler domain MC.
Turns out that the shared cpu_coregroup_mask() requires that the
hot-plugged CPU is removed from the core_sibling mask via
remove_cpu_topology(). Otherwise the 'is core_sibling subset of
cpumask_of_node()' doesn't work. In this case the task scheduler has to
deal with cpumask_of_node instead of core_sibling which is wrong on
scheduler domain MC.
e.g. CPU3 hot-plugged out on TC2 [cluster0: 0,3-4 cluster1: 1-2]:
cpu_coregroup_mask(): CPU3 cpumask_of_node=0-2,4 core_sibling=0,3-4
^
should be:
cpu_coregroup_mask(): CPU3 cpumask_of_node=0-2,4 core_sibling=0,4
Add remove_cpu_topology() to __cpu_disable() to remove the CPU from the
topology masks in case of a CPU hotplug out operation.
At the same time tweak store_cpu_topology() slightly so it will call
update_siblings_masks() in case of CPU hotplug in operation via
secondary_start_kernel()->smp_store_cpu_info().
This aligns the ARM32 implementation with the ARM64 one.
Guarding remove_cpu_topology() with CONFIG_GENERIC_ARCH_TOPOLOGY is
necessary since some Arm32 defconfigs (aspeed_g5_defconfig,
milbeaut_m10v_defconfig, spear13xx_defconfig) specify an explicit
# CONFIG_ARM_CPU_TOPOLOGY is not set
w/ ./arch/arm/Kconfig: select GENERIC_ARCH_TOPOLOGY if ARM_CPU_TOPOLOGY
Fixes: ca74b316df96 ("arm: Use common cpu_topology structure and functions")
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
All pr_warning are removed from kernel, let's cleanup pr_warning
check in checkpatch.
Link: http://lkml.kernel.org/r/20191128004752.35268-5-wangkefeng.wang@huawei.com
To: linux-kernel@vger.kernel.org
Cc: gregkh@linuxfoundation.org
Cc: tj@kernel.org
Cc: arnd@arndb.de
Cc: sergey.senozhatsky@gmail.com
Cc: rostedt@goodmis.org
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
With all pr_warning are removed, saftely drop pr_warning definition.
Link: http://lkml.kernel.org/r/20191128004752.35268-4-wangkefeng.wang@huawei.com
To: joe@perches.com
To: linux-kernel@vger.kernel.org
Cc: gregkh@linuxfoundation.org
Cc: tj@kernel.org
Cc: arnd@arndb.de
Cc: sergey.senozhatsky@gmail.com
Cc: rostedt@goodmis.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
Link: http://lkml.kernel.org/r/20191206092503.303d6a57@canb.auug.org.au
Cc: Linux Next Mailing List <linux-next@vger.kernel.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
Use pr_warn() instead of the remaining pr_warning() calls.
Link: http://lkml.kernel.org/r/20191128004752.35268-2-wangkefeng.wang@huawei.com
To: joe@perches.com
To: linux-kernel@vger.kernel.org
Cc: gregkh@linuxfoundation.org
Cc: tj@kernel.org
Cc: arnd@arndb.de
Cc: sergey.senozhatsky@gmail.com
Cc: rostedt@goodmis.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
Fix pipe_write() to not cache the ring index mask and max_usage as their
values are invalidated by calling pipe_wait() because the latter
function drops the pipe lock, thereby allowing F_SETPIPE_SZ change them.
Without this, pipe_write() may subsequently miscalculate the array
indices and pipe fullness, leading to an oops like the following:
BUG: KASAN: slab-out-of-bounds in pipe_write+0xc25/0xe10 fs/pipe.c:481
Write of size 8 at addr ffff8880771167a8 by task syz-executor.3/7987
...
CPU: 1 PID: 7987 Comm: syz-executor.3 Not tainted 5.4.0-rc2-syzkaller #0
...
Call Trace:
pipe_write+0xc25/0xe10 fs/pipe.c:481
call_write_iter include/linux/fs.h:1895 [inline]
new_sync_write+0x3fd/0x7e0 fs/read_write.c:483
__vfs_write+0x94/0x110 fs/read_write.c:496
vfs_write+0x18a/0x520 fs/read_write.c:558
ksys_write+0x105/0x220 fs/read_write.c:611
__do_sys_write fs/read_write.c:623 [inline]
__se_sys_write fs/read_write.c:620 [inline]
__x64_sys_write+0x6e/0xb0 fs/read_write.c:620
do_syscall_64+0xca/0x5d0 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
This is not a problem for pipe_read() as the mask is recalculated on
each pass of the loop, after pipe_wait() has been called.
Fixes: 8cefc107ca54 ("pipe: Use head and tail pointers for the ring, not cursor and length")
Reported-by: syzbot+838eb0878ffd51f27c41@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Eric Biggers <ebiggers@kernel.org>
[ Changed it to use a temporary variable 'mask' to avoid long lines -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
An assertion check was added to pipe_poll() to make sure that the ring
occupancy isn't seen to overflow the ring size. However, since no locks
are held when the three values are read, it is possible for F_SETPIPE_SZ
to intervene and muck up the calculation, thereby causing the oops.
Fix this by simply removing the assertion and accepting that the
calculation might be approximate.
Note that the previous code also had a similar issue, though there was
no assertion check, since the occupancy counter and the ring size were
not read with a lock held, so it's possible that the poll check might
have malfunctioned then too.
Also wake up all the waiters so that they can reissue their checks if
there was a competing read or write.
Fixes: 8cefc107ca54 ("pipe: Use head and tail pointers for the ring, not cursor and length")
Reported-by: syzbot+d37abaade33a934f16f2@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sock_fprog_kern::len is in units of struct sock_filter, not bytes.
Fixes: 3e859adf3643 ("compat_ioctl: unify copy-in of ppp filters")
Reported-by: syzbot+eb853b51b10f1befa0b7@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, when set VF VLAN with command "ip link set <pf name>
vf <vf id> vlan <vlan id>", the VF ID 0 is handled as PF incorrectly,
which should be the first VF. This patch fixes it.
Fixes: 21e043cd8124 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, hns3_nic_maybe_stop_tx() uses skb_copy() to linearize a
SKB if the BD num required by the SKB does not meet the hardware
limitation, and it linearizes the SKB by allocating a new linearized SKB
and freeing the old SKB, if hns3_nic_maybe_stop_tx() returns -EBUSY
because there are no enough space in the ring to send the linearized
skb to hardware, the sch_direct_xmit() still hold reference to old SKB
and try to retransmit the old SKB when dev_hard_start_xmit() return
TX_BUSY, which may cause use after freed problem.
This patch fixes it by using __skb_linearize() to linearize the
SKB in hns3_nic_maybe_stop_tx().
Fixes: 51e8439f3496 ("net: hns3: add 8 BD limit for tx flow")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is timing window between ring_space checking and
netif_stop_subqueue when transmiting a SKB, and the TX BD
cleaning may be executed during the time window, which may
caused TX queue not restarted problem.
This patch fixes it by rechecking the ring_space after
netif_stop_subqueue to make sure TX queue is restarted.
Also, the ring->next_to_clean is updated even when pkts is
zero, because all the TX BD cleaned may be non-SKB, so it
needs to check if TX queue need to be restarted.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace "select NET_SWITCHDEV" vs "depends on NET_SWITCHDEV" to fix Kconfig
warning with CONFIG_COMPILE_TEST=y
WARNING: unmet direct dependencies detected for NET_SWITCHDEV
Depends on [n]: NET [=y] && INET [=n]
Selected by [y]:
- TI_CPSW_SWITCHDEV [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && (ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST [=y])
because TI_CPSW_SWITCHDEV blindly selects NET_SWITCHDEV even though
INET is not set/enabled, while NET_SWITCHDEV depends on INET.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is mostly to reorder the entries as they've moved in the Kconfig
hierarchies. Doing this periodically (but not very often) simplifies
conflict resolution for new options, etc.
Link: https://lore.kernel.org/r/20191205211438.27552-2-olof@lixom.net
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This is mostly to reorder the entries as they've moved in the Kconfig
hierarchies. Doing this periodically (but not very often) simplifies
conflict resolution for new options, etc.
Link: https://lore.kernel.org/r/20191205211438.27552-3-olof@lixom.net
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In cited commit, when prio tag mode is enabled, FTE creation fails
due to missing group with valid match criteria.
Hence,
(a) create prio tag group metadata_prio_tag_grp when prio tag is
enabled with match criteria for vlan push FTE.
(b) Rename metadata_grp to metadata_allmatch_grp to reflect its purpose.
Also when priority tag is enabled, delete metadata settings after
deleting ingress rules, which are using it.
Tide up rest of the ingress config code for unnecessary labels.
Fixes: 10652f39943e ("net/mlx5: Refactor ingress acl configuration")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When setting speed to 100G via ethtool (AN is set to off), only 25G*4 is
configured while the user, who has an advanced HW which supports
extended PTYS, expects also 50G*2 to be configured.
With this patch, when extended PTYS mode is available, configure
PTYS via extended fields.
Fixes: 4b95840a6ced ("net/mlx5e: Fix matching of speed to PRM link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add a missing value in translation of PTYS ext_eth_proto_oper to its
corresponding speed. When ext_eth_proto_oper bit 10 is set, ethtool
shows unknown speed. With this fix, ethtool shows speed is 100G as
expected.
Fixes: a08b4ed1373d ("net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
It could be neigh update flow took a refcount on peer flow so
sometimes we cannot release peer flow even if parent flow is
being freed now.
Fixes: 5a7e5bcb663d ("net/mlx5e: Extend tc flow struct with reference counter")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Flows are allocated with kzalloc() so free with kfree().
Fixes: 04de7dda7394 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
SFF 8472 eeprom length is 512 bytes. Fix module info return value to
support 512 bytes read.
Fixes: ace329f4ab3b ("net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the user changes prio2buffer mapping while global pause is
enabled, mlx5 driver incorrectly sets all active buffers
(buffer that has at least one priority mapped) to lossy.
Solution:
If global pause is enabled, set all the active buffers to lossless
in prio2buffer command.
Also, add error message when buffer size is not enough to meet
xoff threshold.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Cited patch changed (channel index, tc) => (TXQ index) mapping to be a
static one, in order to keep indices consistent when changing number of
channels or TCs.
For 32 channels (OOB) and 8 TCs, real num of TXQs is 256.
When reducing the amount of channels to 8, the real num of TXQs will be
changed to 64.
This indices method is buggy:
- Channel #0, TC 3, the TXQ index is 96.
- Index 8 is not valid, as there is no such TXQ from driver perspective
(As it represents channel #8, TC 0, which is not valid with the above
configuration).
As part of driver's select queue, it calls netdev_pick_tx which returns an
index in the range of real number of TXQs. Depends on the return value,
with the examples above, driver could have returned index larger than the
real number of tx queues, or crash the kernel as it tries to read invalid
address of SQ which was not allocated.
Fix that by allocating sequential TXQ indices, and hold a new mapping
between (channel index, tc) => (real TXQ index). This mapping will be
updated as part of priv channels activation, and is used in
mlx5e_select_queue to find the selected queue index.
The existing indices mapping (channel_tc2txq) is no longer needed, as it
is used only for statistics structures and can be calculated on run time.
Delete its definintion and updates.
Fixes: 8bfaf07f7806 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit b91d9e67e50b ("s390/cio: fix intparm documentation").
As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.
For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.
Fixes: 405548959cc7 ("s390/qeth: add support for dynamically allocated cmds")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the RX path builds non-linear skbs, the packet headers can
currently spill over into page fragments. Depending on the packet type
and what fields we need to access in the headers, this could cause us
to go past the end of skb->data.
So for non-linear packets, copy precisely the length of the necessary
headers ('linear_len') into skb->data.
And don't copy more, upper-level protocols will peel whatever additional
packet headers they need.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on a packet's type, the RX path needs to access fields in the
packet headers and thus requires a minimum packet length.
Enforce this length when building the skb.
On the other hand a single runt packet is no reason to drop the whole
RX buffer. So just skip it, and continue processing on the next packet.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|