| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
MRP doesn't implement the periodictimer in 802.1Q, so it never retries
if packets get lost. I ran into this problem when MRP sent a MVRP
JoinIn before the interface was fully up. The JoinIn was lost, MRP
didn't retry, and MVRP registration failed.
Tested against Juniper QFabric switches
Signed-off-by: Noel Burton-Krahn <noel@burton-krahn.com>
Acked-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Actually re-send packets when the T1 timer runs out. This fixes a bug
where packets are waiting on the write queue until disconnection when
no other traffic is outstanding.
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NFS client bugfix from Trond Myklebust:
"Fix a regression due to incorrect sharing of gss auth caches"
* tag 'nfs-for-3.12-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
RPCSEC_GSS: fix crash on destroying gss auth
|
|
When the dlc is closed, rfcomm_dev_state_change() tries to release the
port in the case it cannot get a reference to the tty. However this is
racy and not even needed.
Infact as Peter Hurley points out:
1. Only consider dlcs that are 'stolen' from a connected socket, ie.
reused. Allocated dlcs cannot have been closed prior to port
activate and so for these dlcs a tty reference will always be avail
in rfcomm_dev_state_change() -- except for the conditions covered by
#2b below.
2. If a tty was at some point previously created for this rfcomm, then
either
(a) the tty reference is still avail, so rfcomm_dev_state_change()
will perform a hangup. So nothing to do, or,
(b) the tty reference is no longer avail, and the tty_port will be
destroyed by the last tty_port_put() in rfcomm_tty_cleanup.
Again, no action required.
3. Prior to obtaining the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will not 'see' a rfcomm_dev so nothing to
do here.
4. After releasing the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will 'see' an incomplete rfcomm_dev if a
tty reference could not be obtained. Again, the best thing to do here
is nothing. Any future attempted open() will block on
rfcomm_dev_carrier_raised(). The unconnected device will exist until
released by ioctl(RFCOMMRELEASEDEV).
The patch removes the aforementioned code and uses the
tty_port_tty_hangup() helper to hangup the tty.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Pull networking fixes from David Miller:
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
|
|
I've been hitting a NULL ptr deref while using netconsole because the
np->dev check and the pointer manipulation in netpoll_cleanup are done
without rtnl and the following sequence happens when having a netconsole
over a vlan and we remove the vlan while disabling the netconsole:
CPU 1 CPU2
removes vlan and calls the notifier
enters store_enabled(), calls
netdev_cleanup which checks np->dev
and then waits for rtnl
executes the netconsole netdev
release notifier making np->dev
== NULL and releases rtnl
continues to dereference a member of
np->dev which at this point is == NULL
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.
For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->data already points to IP header, but for the sake of
consistency we can also use ip_hdr() to retrieve it.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ceph fixes from Sage Weil:
"These fix several bugs with RBD from 3.11 that didn't get tested in
time for the merge window: some error handling, a use-after-free, and
a sequencing issue when unmapping and image races with a notify
operation.
There is also a patch fixing a problem with the new ceph + fscache
code that just went in"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
fscache: check consistency does not decrement refcount
rbd: fix error handling from rbd_snap_name()
rbd: ignore unmapped snapshots that no longer exist
rbd: fix use-after free of rbd_dev->disk
rbd: make rbd_obj_notify_ack() synchronous
rbd: complete notifies before cleaning up osd_client and rbd_dev
libceph: add function to ensure notifies are complete
|
|
When reading percpu stats we need to properly reset
the sum when CPU 0 is not present in the possible mask.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
commit c5549571f975ab ("ipvs: convert lblcr scheduler to rcu")
allows RCU readers to use dest after calling ip_vs_dest_put().
In the corner case it can race with ip_vs_dest_trash_expire()
which can release the dest while it is being returned to the
RCU readers as scheduling result.
To fix the problem do not allow e->dest to be replaced and
defer the ip_vs_dest_put() call by using RCU callback. Now
e->dest does not need to be RCU pointer.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
commit c2a4ffb70eef39 ("ipvs: convert lblc scheduler to rcu")
allows RCU readers to use dest after calling ip_vs_dest_put().
In the corner case it can race with ip_vs_dest_trash_expire()
which can release the dest while it is being returned to the
RCU readers as scheduling result.
To fix the problem do not allow en->dest to be replaced and
defer the ip_vs_dest_put() call by using RCU callback. Now
en->dest does not need to be RCU pointer.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
commit 578bc3ef1e473a ("ipvs: reorganize dest trash") added
IP_VS_DEST_STATE_REMOVING flag and RCU callback named
ip_vs_dest_wait_readers() to keep dests and services after
removal for at least a RCU grace period. But we have the
following corner cases:
- we can not reuse the same dest if its service is removed
while IP_VS_DEST_STATE_REMOVING is still set because another dest
removal in the first grace period can not extend this period.
It can happen when ipvsadm -C && ipvsadm -R is used.
- dest->svc can be replaced but ip_vs_in_stats() and
ip_vs_out_stats() have no explicit read memory barriers
when accessing dest->svc. It can happen that dest->svc
was just freed (replaced) while we use it to update
the stats.
We solve the problems as follows:
- IP_VS_DEST_STATE_REMOVING is removed and we ensure a fixed
idle period for the dest (IP_VS_DEST_TRASH_PERIOD). idle_start
will remember when for first time after deletion we noticed
dest->refcnt=0. Later, the connections can grab a reference
while in RCU grace period but if refcnt becomes 0 we can
safely free the dest and its svc.
- dest->svc becomes RCU pointer. As result, we add explicit
RCU locking in ip_vs_in_stats() and ip_vs_out_stats().
- __ip_vs_unbind_svc is renamed to __ip_vs_svc_put(), it
now can free the service immediately or after a RCU grace
period. dest->svc is not set to NULL anymore.
As result, unlinked dests and their services are
freed always after IP_VS_DEST_TRASH_PERIOD period, unused
services are freed after a RCU grace period.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Schedulers such as lblc and lblcr require the weight to be as high as the
maximum number of active connections. In commit b552f7e3a9524abcbcdf
("ipvs: unify the formula to estimate the overhead of processing
connections"), the consideration of inactconns and activeconns was cleaned
up to always count activeconns as 256 times more important than inactconns.
In cases where 3000 or more connections are expected, a weight of 3000 *
256 * 3000 connections overflows the 32-bit signed result used to determine
if rescheduling is required.
On amd64, this merely changes the multiply and comparison instructions to
64-bit. On x86, a 64-bit result is already present from imull, so only
a few more comparison instructions are emitted.
Signed-off-by: Simon Kirby <sim@hostway.ca>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
We need to let the setup stage complete cleanly even when the HCI device
is rfkilled. Otherwise the HCI device will stay in an undefined state
and never get notified to user space through mgmt (even when it gets
unblocked through rfkill).
This patch makes sure that hci_dev_open() can be called in the HCI_SETUP
stage, that blocking the device doesn't abort the setup stage, and that
the device gets proper powered down as soon as the setup stage completes
in case it was blocked meanwhile.
The bug that this patch fixed can be very easily reproduced using e.g.
the rfkill command line too. By running "rfkill block all" before
inserting a Bluetooth dongle the resulting HCI device goes into a state
where it is never announced over mgmt, not even when "rfkill unblock all"
is run.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
DCCP shouldn't be setting sk_err on redirects as it
isn't an error condition. it should be doing exactly
what tcp is doing and leaving the error handler without
touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Included change:
- fix the Bridge Loop Avoidance component by marking the variables containing
the VLAN ID with the HAS_TAG flag when needed.
|
|
This fixes a regression since eb6dc19d8e72ce3a957af5511d20c0db0a8bd007
"RPCSEC_GSS: Share all credential caches on a per-transport basis" which
could cause an occasional oops in the nfsd code (see below).
The problem was that an auth was left referencing a client that had been
freed. To avoid this we need to ensure that auths are shared only
between descendants of a common client; the fact that a clone of an
rpc_client takes a reference on its parent then ensures that the parent
client will last as long as the auth.
Also add a comment explaining what I think was the intention of this
code.
general protection fault: 0000 [#1] PREEMPT SMP
Modules linked in: rpcsec_gss_krb5 nfsd auth_rpcgss oid_registry nfs_acl lockd sunrpc
CPU: 3 PID: 4071 Comm: kworker/u8:2 Not tainted 3.11.0-rc2-00182-g025145f #1665
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: nfsd4_callbacks nfsd4_do_callback_rpc [nfsd]
task: ffff88003e206080 ti: ffff88003c384000 task.ti: ffff88003c384000
RIP: 0010:[<ffffffffa00001f3>] [<ffffffffa00001f3>] rpc_net_ns+0x53/0x70 [sunrpc]
RSP: 0000:ffff88003c385ab8 EFLAGS: 00010246
RAX: 6b6b6b6b6b6b6b6b RBX: ffff88003af9a800 RCX: 0000000000000002
RDX: ffffffffa00001a5 RSI: 0000000000000001 RDI: ffffffff81e284e0
RBP: ffff88003c385ad8 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000015 R12: ffff88003c990840
R13: ffff88003c990878 R14: ffff88003c385ba8 R15: ffff88003e206080
FS: 0000000000000000(0000) GS:ffff88003fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fcdf737e000 CR3: 000000003ad2b000 CR4: 00000000000006e0
Stack:
ffffffffa00001a5 0000000000000006 0000000000000006 ffff88003af9a800
ffff88003c385b08 ffffffffa00d52a4 ffff88003c385ba8 ffff88003c751bd8
ffff88003c751bc0 ffff88003e113600 ffff88003c385b18 ffffffffa00d530c
Call Trace:
[<ffffffffa00001a5>] ? rpc_net_ns+0x5/0x70 [sunrpc]
[<ffffffffa00d52a4>] __gss_pipe_release+0x54/0x90 [auth_rpcgss]
[<ffffffffa00d530c>] gss_pipe_free+0x2c/0x30 [auth_rpcgss]
[<ffffffffa00d678b>] gss_destroy+0x9b/0xf0 [auth_rpcgss]
[<ffffffffa000de63>] rpcauth_release+0x23/0x30 [sunrpc]
[<ffffffffa0001e81>] rpc_release_client+0x51/0xb0 [sunrpc]
[<ffffffffa00020d5>] rpc_shutdown_client+0xe5/0x170 [sunrpc]
[<ffffffff81098a14>] ? cpuacct_charge+0xa4/0xb0
[<ffffffff81098975>] ? cpuacct_charge+0x5/0xb0
[<ffffffffa019556f>] nfsd4_process_cb_update.isra.17+0x2f/0x210 [nfsd]
[<ffffffff819a4ac0>] ? _raw_spin_unlock_irq+0x30/0x60
[<ffffffff819a4acb>] ? _raw_spin_unlock_irq+0x3b/0x60
[<ffffffff810703ab>] ? process_one_work+0x15b/0x510
[<ffffffffa01957dd>] nfsd4_do_callback_rpc+0x8d/0xa0 [nfsd]
[<ffffffff8107041e>] process_one_work+0x1ce/0x510
[<ffffffff810703ab>] ? process_one_work+0x15b/0x510
[<ffffffff810712ab>] worker_thread+0x11b/0x370
[<ffffffff81071190>] ? manage_workers.isra.24+0x2b0/0x2b0
[<ffffffff8107854b>] kthread+0xdb/0xe0
[<ffffffff819a4ac0>] ? _raw_spin_unlock_irq+0x30/0x60
[<ffffffff81078470>] ? __init_kthread_worker+0x70/0x70
[<ffffffff819ac7dc>] ret_from_fork+0x7c/0xb0
[<ffffffff81078470>] ? __init_kthread_worker+0x70/0x70
Code: a5 01 00 a0 31 d2 31 f6 48 c7 c7 e0 84 e2 81 e8 f4 91 0a e1 48 8b 43 60 48 c7 c2 a5 01 00 a0 be 01 00 00 00 48 c7 c7 e0 84 e2 81 <48> 8b 98 10 07 00 00 e8 91 8f 0a e1 e8
+3c 4e 07 e1 48 83 c4 18
RIP [<ffffffffa00001f3>] rpc_net_ns+0x53/0x70 [sunrpc]
RSP <ffff88003c385ab8>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for you net tree,
mostly targeted to ipset, they are:
* Fix ICMPv6 NAT due to wrong comparison, code instead of type, from
Phil Oester.
* Fix RCU race in conntrack extensions release path, from Michal Kubecek.
* Fix missing inversion in the userspace ipset test command match if
the nomatch option is specified, from Jozsef Kadlecsik.
* Skip layer 4 protocol matching in ipset in case of IPv6 fragments,
also from Jozsef Kadlecsik.
* Fix sequence adjustment in nfnetlink_queue due to using the netlink
skb instead of the network skb, from Gao feng.
* Make sure we cannot swap of sets with different layer 3 family in
ipset, from Jozsef Kadlecsik.
* Fix possible bogus matching in ipset if hash sets with net elements
are used, from Oliver Smith.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1b7fdd2ab5852 ("tcp: do not use cached RTT for RTT estimation")
did not correctly account for the fact that crtt is the RTT shifted
left 3 bits. Fix the calculation to consistently reflect this fact.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-By: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving or sending a packet a packet on a VLAN, the
vid has to be marked with the TAG flag in order to make any
component in batman-adv understand that the packet is coming
from a really tagged network.
This fix the Bridge Loop Avoidance behaviour which was not
able to send announces over VLAN interfaces.
Introduced by 0b1da1765fdb00ca5d53bc95c9abc70dfc9aae5b
("batman-adv: change VID semantic in the BLA code")
Signed-off-by: Antonio Quartulli <antonio@open-mesh.org>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Instead of the netlink skb.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Adapt the same behaviour for SCTP as present in TCP for ICMP redirect
messages. For IPv6, RFC4443, section 2.4. says:
...
(e) An ICMPv6 error message MUST NOT be originated as a result of
receiving the following:
...
(e.2) An ICMPv6 redirect message [IPv6-DISC].
...
Therefore, do not report an error to user space, just invoke dst's redirect
callback and leave, same for IPv4 as done in TCP as well. The implication
w/o having this patch could be that the reception of such packets would
generate a poll notification and in worst case it could even tear down the
whole connection. Therefore, stop updating sk_err on redirects.
Reported-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IFLA_IPTUN_LOCAL and IFLA_IPTUN_REMOTE were inverted.
Introduced by c075b13098b3 (ip6tnl: advertise tunnel param via rtnl).
Signed-off-by: Ding Zhi <zhi.ding@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a serious bug affecting all hash types with a net element -
specifically, if a CIDR value is deleted such that none of the same size
exist any more, all larger (less-specific) values will then fail to
match. Adding back any prefix with a CIDR equal to or more specific than
the one deleted will fix it.
Steps to reproduce:
ipset -N test hash:net
ipset -A test 1.1.0.0/16
ipset -A test 2.2.2.0/24
ipset -T test 1.1.1.1 #1.1.1.1 IS in set
ipset -D test 2.2.2.0/24
ipset -T test 1.1.1.1 #1.1.1.1 IS NOT in set
This is due to the fact that the nets counter was unconditionally
decremented prior to the iteration that shifts up the entries. Now, we
first check if there is a proceeding entry and if not, decrement it and
return. Otherwise, we proceed to iterate and then zero the last element,
which, in most cases, will already be zero.
Signed-off-by: Oliver Smith <oliver@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
|
|
This closes netfilter bugzilla #843, reported by Quentin Armitage.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
|
|
The "nomatch" commandline flag should invert the matching at testing,
similarly to the --return-nomatch flag of the "set" match of iptables.
Until now it worked with the elements with "nomatch" flag only. From
now on it works with elements without the flag too, i.e:
# ipset n test hash:net
# ipset a test 10.0.0.0/24 nomatch
# ipset t test 10.0.0.1
10.0.0.1 is NOT in set test.
# ipset t test 10.0.0.1 nomatch
10.0.0.1 is in set test.
# ipset a test 192.168.0.0/24
# ipset t test 192.168.0.1
192.168.0.1 is in set test.
# ipset t test 192.168.0.1 nomatch
192.168.0.1 is NOT in set test.
Before the patch the results were
...
# ipset t test 192.168.0.1
192.168.0.1 is in set test.
# ipset t test 192.168.0.1 nomatch
192.168.0.1 is in set test.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
|
|
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
|
|
For certain devices (ex: HID mouse), support for authentication,
pairing and bonding is optional. For such devices, the ACL alive
for too long after the L2CAP disconnection.
To avoid the ACL alive for too long after L2CAP disconnection, reset the
ACL disconnect timeout back to HCI_DISCONN_TIMEOUT during L2CAP connect.
While merging the commit id:a9ea3ed9b71cc3271dd59e76f65748adcaa76422
this issue might have introduced.
Hcidump info:
sh-4.1# /opt/hcidump -Xt
2013-08-05 16:49:00.894129 < ACL data: handle 12 flags 0x00 dlen 12
L2CAP(s): Disconn req: dcid 0x004a scid 0x0041
2013-08-05 16:49:00.894195 < HCI Command: Exit Sniff Mode (0x02|0x0004)
plen 2
handle 12
2013-08-05 16:49:00.894269 < ACL data: handle 12 flags 0x00 dlen 12
L2CAP(s): Disconn req: dcid 0x0049 scid 0x0040
2013-08-05 16:49:00.895645 > HCI Event: Command Status (0x0f) plen 4
Exit Sniff Mode (0x02|0x0004) status 0x00 ncmd 1
2013-08-05 16:49:00.934391 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x00 interval 0
Mode: Active
2013-08-05 16:49:00.936592 > HCI Event: Number of Completed Packets
(0x13) plen 5
handle 12 packets 2
2013-08-05 16:49:00.951577 > ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x004a scid 0x0041
2013-08-05 16:49:00.952820 > ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x0049 scid 0x0040
2013-08-05 16:49:00.969165 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x02 interval 50
Mode: Sniff
2013-08-05 16:49:48.175533 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x00 interval 0
Mode: Active
2013-08-05 16:49:48.219045 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x02 interval 108
Mode: Sniff
2013-08-05 16:51:00.968209 < HCI Command: Disconnect (0x01|0x0006) plen 3
handle 12 reason 0x13
Reason: Remote User Terminated Connection
2013-08-05 16:51:00.969056 > HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) status 0x00 ncmd 1
2013-08-05 16:51:01.013495 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x00 interval 0
Mode: Active
2013-08-05 16:51:01.073777 > HCI Event: Disconn Complete (0x05) plen 4
status 0x00 handle 12 reason 0x16
Reason: Connection Terminated by Local Host
============================ After fix ================================
2013-08-05 16:57:35.986648 < ACL data: handle 11 flags 0x00 dlen 12
L2CAP(s): Disconn req: dcid 0x004c scid 0x0041
2013-08-05 16:57:35.986713 < HCI Command: Exit Sniff Mode (0x02|0x0004)
plen 2
handle 11
2013-08-05 16:57:35.986785 < ACL data: handle 11 flags 0x00 dlen 12
L2CAP(s): Disconn req: dcid 0x004b scid 0x0040
2013-08-05 16:57:35.988110 > HCI Event: Command Status (0x0f) plen 4
Exit Sniff Mode (0x02|0x0004) status 0x00 ncmd 1
2013-08-05 16:57:36.030714 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 11 mode 0x00 interval 0
Mode: Active
2013-08-05 16:57:36.032950 > HCI Event: Number of Completed Packets
(0x13) plen 5
handle 11 packets 2
2013-08-05 16:57:36.047926 > ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x004c scid 0x0041
2013-08-05 16:57:36.049200 > ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x004b scid 0x0040
2013-08-05 16:57:36.065509 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 11 mode 0x02 interval 50
Mode: Sniff
2013-08-05 16:57:40.052006 < HCI Command: Disconnect (0x01|0x0006) plen 3
handle 11 reason 0x13
Reason: Remote User Terminated Connection
2013-08-05 16:57:40.052869 > HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) status 0x00 ncmd 1
2013-08-05 16:57:40.104731 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 11 mode 0x00 interval 0
Mode: Active
2013-08-05 16:57:40.146935 > HCI Event: Disconn Complete (0x05) plen 4
status 0x00 handle 11 reason 0x16
Reason: Connection Terminated by Local Host
Signed-off-by: Sang-Ki Park <sangki79.park@samsung.com>
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch fixes the connection encryption key size information when
the host is playing the peripheral role. We should set conn->enc_key_
size in hci_le_ltk_request_evt, otherwise it is left uninitialized.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
While playing the peripheral role, the host gets a LE Long Term Key
Request Event from the controller when a connection is established
with a bonded device. The host then informs the LTK which should be
used for the connection. Once the link is encrypted, the host gets
an Encryption Change Event.
Therefore we should set conn->pending_sec_level instead of conn->
sec_level in hci_le_ltk_request_evt. This way, conn->sec_level is
properly updated in hci_encrypt_change_evt.
Moreover, since we have a LTK associated to the device, we have at
least BT_SECURITY_MEDIUM security level.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The NULL deref happens when br_handle_frame is called between these
2 lines of del_nbp:
dev->priv_flags &= ~IFF_BRIDGE_PORT;
/* --> br_handle_frame is called at this time */
netdev_rx_handler_unregister(dev);
In br_handle_frame the return of br_port_get_rcu(dev) is dereferenced
without check but br_port_get_rcu(dev) returns NULL if:
!(dev->priv_flags & IFF_BRIDGE_PORT)
Eric Dumazet pointed out the testing of IFF_BRIDGE_PORT is not necessary
here since we're in rcu_read_lock and we have synchronize_net() in
netdev_rx_handler_unregister. So remove the testing of IFF_BRIDGE_PORT
and by the previous patch, make sure br_port_get_rcu is called in
bridging code.
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
current br_port_get_rcu is problematic in bridging path
(NULL deref). Change these calls in netlink path first.
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull aio changes from Ben LaHaise:
"First off, sorry for this pull request being late in the merge window.
Al had raised a couple of concerns about 2 items in the series below.
I addressed the first issue (the race introduced by Gu's use of
mm_populate()), but he has not provided any further details on how he
wants to rework the anon_inode.c changes (which were sent out months
ago but have yet to be commented on).
The bulk of the changes have been sitting in the -next tree for a few
months, with all the issues raised being addressed"
* git://git.kvack.org/~bcrl/aio-next: (22 commits)
aio: rcu_read_lock protection for new rcu_dereference calls
aio: fix race in ring buffer page lookup introduced by page migration support
aio: fix rcu sparse warnings introduced by ioctx table lookup patch
aio: remove unnecessary debugging from aio_free_ring()
aio: table lookup: verify ctx pointer
staging/lustre: kiocb->ki_left is removed
aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
aio: convert the ioctx list to table lookup v3
aio: double aio_max_nr in calculations
aio: Kill ki_dtor
aio: Kill ki_users
aio: Kill unneeded kiocb members
aio: Kill aio_rw_vect_retry()
aio: Don't use ctx->tail unnecessarily
aio: io_cancel() no longer returns the io_event
aio: percpu ioctx refcount
aio: percpu reqs_available
aio: reqs_active -> reqs_available
aio: fix build when migration is disabled
...
|
|
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
In commit 58a317f1 (netfilter: ipv6: add IPv6 NAT support), icmpv6_manip_pkt
was added with an incorrect comparison of ICMP codes to types. This causes
problems when using NAT rules with the --random option. Correct the
comparison.
This closes netfilter bugzilla #851, reported by Alexander Neumann.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
At some point limits were added to forward_delay. However, the
limits are only enforced when STP is enabled. This created a
scenario where you could have a value outside the allowed range
while STP is disabled, which then stuck around even after STP
is enabled.
This patch fixes this by clamping the value when we enable STP.
I had to move the locking around a bit to ensure that there is
no window where someone could insert a value outside the range
while we're in the middle of enabling STP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This changes the message_age_timer calculation to use the BPDU's max age as
opposed to the local bridge's max age. This is in accordance with section
8.6.2.3.2 Step 2 of the 802.1D-1998 sprecification.
With the current implementation, when running with very large bridge
diameters, convergance will not always occur even if a root bridge is
configured to have a longer max age.
Tested successfully on bridge diameters of ~200.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge more patches from Andrew Morton:
"The rest of MM. Plus one misc cleanup"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
mm/Kconfig: add MMU dependency for MIGRATION.
kernel: replace strict_strto*() with kstrto*()
mm, thp: count thp_fault_fallback anytime thp fault fails
thp: consolidate code between handle_mm_fault() and do_huge_pmd_anonymous_page()
thp: do_huge_pmd_anonymous_page() cleanup
thp: move maybe_pmd_mkwrite() out of mk_huge_pmd()
mm: cleanup add_to_page_cache_locked()
thp: account anon transparent huge pages into NR_ANON_PAGES
truncate: drop 'oldsize' truncate_pagecache() parameter
mm: make lru_add_drain_all() selective
memcg: document cgroup dirty/writeback memory statistics
memcg: add per cgroup writeback pages accounting
memcg: check for proper lock held in mem_cgroup_update_page_stat
memcg: remove MEMCG_NR_FILE_MAPPED
memcg: reduce function dereference
memcg: avoid overflow caused by PAGE_ALIGN
memcg: rename RESOURCE_MAX to RES_COUNTER_MAX
memcg: correct RESOURCE_MAX to ULLONG_MAX
mm: memcg: do not trap chargers with full callstack on OOM
mm: memcg: rework and document OOM waiting and wakeup
...
|
|
RESOURCE_MAX is far too general name, change it to RES_COUNTER_MAX.
Signed-off-by: Sha Zhengju <handai.szj@taobao.com>
Signed-off-by: Qiang Huang <h.huangqiang@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Jeff Liu <jeff.liu@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull vfs pile 4 from Al Viro:
"list_lru pile, mostly"
This came out of Andrew's pile, Al ended up doing the merge work so that
Andrew didn't have to.
Additionally, a few fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (42 commits)
super: fix for destroy lrus
list_lru: dynamically adjust node arrays
shrinker: Kill old ->shrink API.
shrinker: convert remaining shrinkers to count/scan API
staging/lustre/libcfs: cleanup linux-mem.h
staging/lustre/ptlrpc: convert to new shrinker API
staging/lustre/obdclass: convert lu_object shrinker to count/scan API
staging/lustre/ldlm: convert to shrinkers to count/scan API
hugepage: convert huge zero page shrinker to new shrinker API
i915: bail out earlier when shrinker cannot acquire mutex
drivers: convert shrinkers to new count/scan API
fs: convert fs shrinkers to new scan/count API
xfs: fix dquot isolation hang
xfs-convert-dquot-cache-lru-to-list_lru-fix
xfs: convert dquot cache lru to list_lru
xfs: rework buffer dispose list tracking
xfs-convert-buftarg-lru-to-generic-code-fix
xfs: convert buftarg LRU to generic code
fs: convert inode and dentry shrinking to be node aware
vmscan: per-node deferred work
...
|
|
Alan Chester reported an issue with IPv6 on SCTP that IPsec traffic is not
being encrypted, whereas on IPv4 it is. Setting up an AH + ESP transport
does not seem to have the desired effect:
SCTP + IPv4:
22:14:20.809645 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 116)
192.168.0.2 > 192.168.0.5: AH(spi=0x00000042,sumlen=16,seq=0x1): ESP(spi=0x00000044,seq=0x1), length 72
22:14:20.813270 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 340)
192.168.0.5 > 192.168.0.2: AH(spi=0x00000043,sumlen=16,seq=0x1):
SCTP + IPv6:
22:31:19.215029 IP6 (class 0x02, hlim 64, next-header SCTP (132) payload length: 364)
fe80::222:15ff:fe87:7fc.3333 > fe80::92e6:baff:fe0d:5a54.36767: sctp
1) [INIT ACK] [init tag: 747759530] [rwnd: 62464] [OS: 10] [MIS: 10]
Moreover, Alan says:
This problem was seen with both Racoon and Racoon2. Other people have seen
this with OpenSwan. When IPsec is configured to encrypt all upper layer
protocols the SCTP connection does not initialize. After using Wireshark to
follow packets, this is because the SCTP packet leaves Box A unencrypted and
Box B believes all upper layer protocols are to be encrypted so it drops
this packet, causing the SCTP connection to fail to initialize. When IPsec
is configured to encrypt just SCTP, the SCTP packets are observed unencrypted.
In fact, using `socat sctp6-listen:3333 -` on one end and transferring "plaintext"
string on the other end, results in cleartext on the wire where SCTP eventually
does not report any errors, thus in the latter case that Alan reports, the
non-paranoid user might think he's communicating over an encrypted transport on
SCTP although he's not (tcpdump ... -X):
...
0x0030: 5d70 8e1a 0003 001a 177d eb6c 0000 0000 ]p.......}.l....
0x0040: 0000 0000 706c 6169 6e74 6578 740a 0000 ....plaintext...
Only in /proc/net/xfrm_stat we can see XfrmInTmplMismatch increasing on the
receiver side. Initial follow-up analysis from Alan's bug report was done by
Alexey Dobriyan. Also thanks to Vlad Yasevich for feedback on this.
SCTP has its own implementation of sctp_v6_xmit() not calling inet6_csk_xmit().
This has the implication that it probably never really got updated along with
changes in inet6_csk_xmit() and therefore does not seem to invoke xfrm handlers.
SCTP's IPv4 xmit however, properly calls ip_queue_xmit() to do the work. Since
a call to inet6_csk_xmit() would solve this problem, but result in unecessary
route lookups, let us just use the cached flowi6 instead that we got through
sctp_v6_get_dst(). Since all SCTP packets are being sent through sctp_packet_transmit(),
we do the route lookup / flow caching in sctp_transport_route(), hold it in
tp->dst and skb_dst_set() right after that. If we would alter fl6->daddr in
sctp_v6_xmit() to np->opt->srcrt, we possibly could run into the same effect
of not having xfrm layer pick it up, hence, use fl6_update_dst() in sctp_v6_get_dst()
instead to get the correct source routed dst entry, which we assign to the skb.
Also source address routing example from 625034113 ("sctp: fix sctp to work with
ipv6 source address routing") still works with this patch! Nevertheless, in RFC5095
it is actually 'recommended' to not use that anyway due to traffic amplification [1].
So it seems we're not supposed to do that anyway in sctp_v6_xmit(). Moreover, if
we overwrite the flow destination here, the lower IPv6 layer will be unable to
put the correct destination address into IP header, as routing header is added in
ipv6_push_nfrag_opts() but then probably with wrong final destination. Things aside,
result of this patch is that we do not have any XfrmInTmplMismatch increase plus on
the wire with this patch it now looks like:
SCTP + IPv6:
08:17:47.074080 IP6 2620:52:0:102f:7a2b:cbff:fe27:1b0a > 2620:52:0:102f:213:72ff:fe32:7eba:
AH(spi=0x00005fb4,seq=0x1): ESP(spi=0x00005fb5,seq=0x1), length 72
08:17:47.074264 IP6 2620:52:0:102f:213:72ff:fe32:7eba > 2620:52:0:102f:7a2b:cbff:fe27:1b0a:
AH(spi=0x00003d54,seq=0x1): ESP(spi=0x00003d55,seq=0x1), length 296
This fixes Kernel Bugzilla 24412. This security issue seems to be present since
2.6.18 kernels. Lets just hope some big passive adversary in the wild didn't have
its fun with that. lksctp-tools IPv6 regression test suite passes as well with
this patch.
[1] http://www.secdev.org/conf/IPv6_RH_security-csw07.pdf
Reported-by: Alan Chester <alan.chester@tekelec.com>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The received ARP request type in the Ethernet packet head is ETH_P_ARP other than ETH_P_IP.
[ Bug introduced by commit b7394d2429c198b1da3d46ac39192e891029ec0f
("netpoll: prepare for ipv6") ]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NFS client bugfixes (part 2) from Trond Myklebust:
"Bugfixes:
- Fix a few credential reference leaks resulting from the
SP4_MACH_CRED NFSv4.1 state protection code.
- Fix the SUNRPC bloatometer footprint: convert a 256K hashtable into
the intended 64 byte structure.
- Fix a long standing XDR issue with FREE_STATEID
- Fix a potential WARN_ON spamming issue
- Fix a missing dprintk() kuid conversion
New features:
- Enable the NFSv4.1 state protection support for the WRITE and
COMMIT operations"
* tag 'nfs-for-3.12-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: No, I did not intend to create a 256KiB hashtable
sunrpc: Add missing kuids conversion for printing
NFSv4.1: sp4_mach_cred: WARN_ON -> WARN_ON_ONCE
NFSv4.1: sp4_mach_cred: no need to ref count creds
NFSv4.1: fix SECINFO* use of put_rpccred
NFSv4.1: sp4_mach_cred: ask for WRITE and COMMIT
NFSv4.1 fix decode_free_stateid
|
|
Fix the declaration of the gss_auth_hash_table so that it creates
a 16 bucket hashtable, as I had intended.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
m68k/allmodconfig:
net/sunrpc/auth_generic.c: In function ‘generic_key_timeout’:
net/sunrpc/auth_generic.c:241: warning: format ‘%d’ expects type ‘int’, but
argument 2 has type ‘kuid_t’
commit cdba321e291f0fbf5abda4d88340292b858e3d4d ("sunrpc: Convert kuids and
kgids to uids and gids for printing") forgot to convert one instance.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Merge first patch-bomb from Andrew Morton:
- Some pidns/fork/exec tweaks
- OCFS2 updates
- Most of MM - there remain quite a few memcg parts which depend on
pending core cgroups changes. Which might have been already merged -
I'll check tomorrow...
- Various misc stuff all over the place
- A few block bits which I never got around to sending to Jens -
relatively minor things.
- MAINTAINERS maintenance
- A small number of lib/ updates
- checkpatch updates
- epoll
- firmware/dmi-scan
- Some kprobes work for S390
- drivers/rtc updates
- hfsplus feature work
- vmcore feature work
- rbtree upgrades
- AOE updates
- pktcdvd cleanups
- PPS
- memstick
- w1
- New "inittmpfs" feature, which does the obvious
- More IPC work from Davidlohr.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (303 commits)
lz4: fix compression/decompression signedness mismatch
ipc: drop ipc_lock_check
ipc, shm: drop shm_lock_check
ipc: drop ipc_lock_by_ptr
ipc, shm: guard against non-existant vma in shmdt(2)
ipc: document general ipc locking scheme
ipc,msg: drop msg_unlock
ipc: rename ids->rw_mutex
ipc,shm: shorten critical region for shmat
ipc,shm: cleanup do_shmat pasta
ipc,shm: shorten critical region for shmctl
ipc,shm: make shmctl_nolock lockless
ipc,shm: introduce shmctl_nolock
ipc: drop ipcctl_pre_down
ipc,shm: shorten critical region in shmctl_down
ipc,shm: introduce lockless functions to obtain the ipc object
initmpfs: use initramfs if rootfstype= or root= specified
initmpfs: make rootfs use tmpfs when CONFIG_TMPFS enabled
initmpfs: move rootfs code from fs/ramfs/ to init/
initmpfs: move bdi setup from init_rootfs to init_ramfs
...
|
|
I found the following pattern that leads in to interesting findings:
grep -r "ret.*|=.*__put_user" *
grep -r "ret.*|=.*__get_user" *
grep -r "ret.*|=.*__copy" *
The __put_user() calls in compat_ioctl.c, ptrace compat, signal compat,
since those appear in compat code, we could probably expect the kernel
addresses not to be reachable in the lower 32-bit range, so I think they
might not be exploitable.
For the "__get_user" cases, I don't think those are exploitable: the worse
that can happen is that the kernel will copy kernel memory into in-kernel
buffers, and will fail immediately afterward.
The alpha csum_partial_copy_from_user() seems to be missing the
access_ok() check entirely. The fix is inspired from x86. This could
lead to information leak on alpha. I also noticed that many architectures
map csum_partial_copy_from_user() to csum_partial_copy_generic(), but I
wonder if the latter is performing the access checks on every
architectures.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
1) Brown paper bag fix in HTB scheduler, class options set incorrectly
due to a typoe. Fix from Vimalkumar.
2) It's possible for the ipv6 FIB garbage collector to run before all
the necessary datastructure are setup during init, defer the
notifier registry to avoid this problem. Fix from Michal Kubecek.
3) New i40e ethernet driver from the Intel folks.
4) Add new qmi wwan device IDs, from Bjørn Mork.
5) Doorbell lock in bnx2x driver is not initialized properly in some
configurations, fix from Ariel Elior.
6) Revert an ipv6 packet option padding change that broke standardized
ipv6 implementation test suites. From Jiri Pirko.
7) Fix synchronization of ARP information in bonding layer, from
Nikolay Aleksandrov.
8) Fix missing error return resulting in illegal memory accesses in
openvswitch, from Daniel Borkmann.
9) SCTP doesn't signal poll events properly due to mistaken operator
precedence, fix also from Daniel Borkmann.
10) __netdev_pick_tx() passes wrong index to sk_tx_queue_set() which
essentially disables caching of TX queue in sockets :-/ Fix from
Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net_sched: htb: fix a typo in htb_change_class()
net: qmi_wwan: add new Qualcomm devices
ipv6: don't call fib6_run_gc() until routing is ready
net: tilegx driver: avoid compiler warning
fib6_rules: fix indentation
irda: vlsi_ir: Remove casting the return value which is a void pointer
irda: donauboe: Remove casting the return value which is a void pointer
net: fix multiqueue selection
net: sctp: fix smatch warning in sctp_send_asconf_del_ip
net: sctp: fix bug in sctp_poll for SOCK_SELECT_ERR_QUEUE
net: fib: fib6_add: fix potential NULL pointer dereference
net: ovs: flow: fix potential illegal memory access in __parse_flow_nlattrs
bcm63xx_enet: remove deprecated IRQF_DISABLED
net: korina: remove deprecated IRQF_DISABLED
macvlan: Move skb_clone check closer to call
qlcnic: Fix warning reported by kbuild test robot.
bonding: fix bond_arp_rcv setting and arp validate desync state
bonding: fix store_arp_validate race with mode change
ipv6/exthdrs: accept tlv which includes only padding
bnx2x: avoid atomic allocations during initialization
...
|
Noel Burton-Krahn
josselin.costanzi@mobile-devices.fr
Linus Torvalds
Gianluca Anzolin
Nikolay Aleksandrov
Ansis Atteka
Julian Anastasov
Simon Kirby
Johan Hedberg
Duan Jiong
David S. Miller
J. Bruce Fields
Neal Cardwell
Antonio Quartulli
Gao feng
Daniel Borkmann
Ding Zhi
Oliver Smith
Jozsef Kadlecsik
Syam Sidhardhan
Andre Guedes
Hong Zhiguo
Martin Schwidefsky
Phil Oester
Herbert Xu
Chris Healy
Sha Zhengju
Sonic Zhang
Trond Myklebust
Geert Uytterhoeven
Mathieu Desnoyers