| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
1) Count ttl-dropped frames properly in mac80211, from Bob Copeland.
2) Integer overflow in ktime handling of bcm can code, from Oliver
Hartkopp.
3) Fix RX desc handling wrt. hw checksumming in ravb, from Simon
Horman.
4) Various hash key fixes in hv_netvsc, from Haiyang Zhang.
5) Use after free in ax25, from Eric Dumazet.
6) Several fixes to the SSN support in SCTP, from Xin Long.
7) Do not process frames after a NAPI reschedule in ibmveth, from
Thomas Falcon.
8) Fix NLA_POLICY_NESTED arguments, from Johannes Berg.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
qed: Revert error handling changes.
cfg80211: extend range deviation for DMG
cfg80211: reg: remove warn_on for a normal case
mac80211: Add attribute aligned(2) to struct 'action'
mac80211: don't initiate TDLS connection if station is not associated to AP
nl80211: fix NLA_POLICY_NESTED() arguments
ibmveth: Do not process frames after calling napi_reschedule
net: dev_is_mac_header_xmit() true for ARPHRD_RAWIP
net: usb: asix: ax88772_bind return error when hw_reset fail
MAINTAINERS: Update cavium networking drivers
net/mlx4_core: Fix error handling when initializing CQ bufs in the driver
net/mlx4_core: Add masking for a few queries on HCA caps
sctp: set flow sport from saddr only when it's 0
sctp: set chunk transport correctly when it's a new asoc
sctp: improve the events for sctp stream adding
sctp: improve the events for sctp stream reset
ip_tunnel: Make none-tunnel-dst tunnel port work with lwtunnel
ax25: fix possible use-after-free
sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe
hv_netvsc: fix typos in code comments
...
|
|
Johannes Berg says:
====================
Just a few small fixes:
* avoid trying to operate TDLS when not connection,
this is not valid and led to issues
* count TTL-dropped frames in mesh better
* deal with new WiGig channels in regulatory code
* remove a WARN_ON() that can trigger due to benign
races during device/driver registration
* fix nested netlink policy maxattrs (syzkaller)
* fix hwsim n_limits (syzkaller)
* propagate __aligned(2) to a surrounding struct
* return proper error in virt_wifi error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently, DMG frequency bands have been extended till 71GHz, so extend
the range check till 20GHz (45-71GHZ), else some channels will be marked
as disabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If there are simulatenous queries of regdb, then there might be a case
where multiple queries can trigger request_firmware_no_wait and can have
parallel callbacks being executed asynchronously. In this scenario we
might hit the WARN_ON.
So remove the warn_on, as the code already handles multiple callbacks
gracefully.
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During refactor in commit 9e478066eae4 ("mac80211: fix MU-MIMO
follow-MAC mode") a new struct 'action' was declared with packed
attribute as:
struct {
struct ieee80211_hdr_3addr hdr;
u8 category;
u8 action_code;
} __packed action;
But since struct 'ieee80211_hdr_3addr' is declared with an aligned
keyword as:
struct ieee80211_hdr {
__le16 frame_control;
__le16 duration_id;
u8 addr1[ETH_ALEN];
u8 addr2[ETH_ALEN];
u8 addr3[ETH_ALEN];
__le16 seq_ctrl;
u8 addr4[ETH_ALEN];
} __packed __aligned(2);
Solve the ambiguity of placing aligned structure in a packed one by
adding the aligned(2) attribute to struct 'action'.
This removes the following warning (W=1):
net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned]
Cc: Johannes Berg <johannes.berg@intel.com>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Following call trace is observed while adding TDLS peer entry in driver
during TDLS setup.
Call Trace:
[<c1301476>] dump_stack+0x47/0x61
[<c10537d2>] __warn+0xe2/0x100
[<fa22415f>] ? sta_apply_parameters+0x49f/0x550 [mac80211]
[<c1053895>] warn_slowpath_null+0x25/0x30
[<fa22415f>] sta_apply_parameters+0x49f/0x550 [mac80211]
[<fa20ad42>] ? sta_info_alloc+0x1c2/0x450 [mac80211]
[<fa224623>] ieee80211_add_station+0xe3/0x160 [mac80211]
[<c1876fe3>] nl80211_new_station+0x273/0x420
[<c170f6d9>] genl_rcv_msg+0x219/0x3c0
[<c170f4c0>] ? genl_rcv+0x30/0x30
[<c170ee7e>] netlink_rcv_skb+0x8e/0xb0
[<c170f4ac>] genl_rcv+0x1c/0x30
[<c170e8aa>] netlink_unicast+0x13a/0x1d0
[<c170ec18>] netlink_sendmsg+0x2d8/0x390
[<c16c5acd>] sock_sendmsg+0x2d/0x40
[<c16c6369>] ___sys_sendmsg+0x1d9/0x1e0
Fixing this by allowing TDLS setup request only when we have completed
association.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
syzbot reported an out-of-bounds read when passing certain
malformed messages into nl80211. The specific place where
this happened isn't interesting, the problem is that nested
policy parsing was referring to the wrong maximum attribute
and thus the policy wasn't long enough.
Fix this by referring to the correct attribute. Since this
is really not necessary, I'll come up with a separate patch
to just pass the policy instead of both, in the common case
we can infer the maxattr from the size of the policy array.
Reported-by: syzbot+4157b036c5f4713b1f2f@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Marc Kleine-Budde says:
====================
pull-request: can 2019-01-22
this is a pull request of 4 patches for net/master.
The first patch by is by Manfred Schlaegl and reverts a patch that caused wrong
warning messages in certain use cases. The next patch is by Oliver Hartkopp for
the bcm that adds sanity checks for the timer value before using it to detect
potential interger overflows. The last two patches are for the flexcan driver,
YueHaibing's patch fixes the the return value in the error path of the
flexcan_setup_stop_mode() function. The second patch is by Uwe Kleine-König and
fixes a NULL pointer deref on older flexcan cores in flexcan_chip_start().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now sctp_transport_pmtu() passes transport->saddr into .get_dst() to set
flow sport from 'saddr'. However, transport->saddr is set only when
transport->dst exists in sctp_transport_route().
If sctp_transport_pmtu() is called without transport->saddr set, like
when transport->dst doesn't exists, the flow sport will be set to 0
from transport->saddr, which will cause a wrong route to be got.
Commit 6e91b578bf3f ("sctp: re-use sctp_transport_pmtu in
sctp_transport_route") made the issue be triggered more easily
since sctp_transport_pmtu() would be called in sctp_transport_route()
after that.
In gerneral, fl4->fl4_sport should always be set to
htons(asoc->base.bind_addr.port), unless transport->asoc doesn't exist
in sctp_v4/6_get_dst(), which is the case:
sctp_ootb_pkt_new() ->
sctp_transport_route()
For that, we can simply handle it by setting flow sport from saddr only
when it's 0 in sctp_v4/6_get_dst().
Fixes: 6e91b578bf3f ("sctp: re-use sctp_transport_pmtu in sctp_transport_route")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the paths:
sctp_sf_do_unexpected_init() ->
sctp_make_init_ack()
sctp_sf_do_dupcook_a/b()() ->
sctp_sf_do_5_1D_ce()
The new chunk 'retval' transport is set from the incoming chunk 'chunk'
transport. However, 'retval' transport belong to the new asoc, which
is a different one from 'chunk' transport's asoc.
It will cause that the 'retval' chunk gets set with a wrong transport.
Later when sending it and because of Commit b9fd683982c9 ("sctp: add
sctp_packet_singleton"), sctp_packet_singleton() will set some fields,
like vtag to 'retval' chunk from that wrong transport's asoc.
This patch is to fix it by setting 'retval' transport correctly which
belongs to the right asoc in sctp_make_init_ack() and
sctp_sf_do_5_1D_ce().
Fixes: b9fd683982c9 ("sctp: add sctp_packet_singleton")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to improve sctp stream adding events in 2 places:
1. In sctp_process_strreset_addstrm_out(), move up SCTP_MAX_STREAM
and in stream allocation failure checks, as the adding has to
succeed after reconf_timer stops for the in stream adding
request retransmission.
3. In sctp_process_strreset_addstrm_in(), no event should be sent,
as no in or out stream is added here.
Fixes: 50a41591f110 ("sctp: implement receiver-side procedures for the Add Outgoing Streams Request Parameter")
Fixes: c5c4ebb3ab87 ("sctp: implement receiver-side procedures for the Add Incoming Streams Request Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to improve sctp stream reset events in 4 places:
1. In sctp_process_strreset_outreq(), the flag should always be set with
SCTP_STREAM_RESET_INCOMING_SSN instead of OUTGOING, as receiver's in
stream is reset here.
2. In sctp_process_strreset_outreq(), move up SCTP_STRRESET_ERR_WRONG_SSN
check, as the reset has to succeed after reconf_timer stops for the
in stream reset request retransmission.
3. In sctp_process_strreset_inreq(), no event should be sent, as no in
or out stream is reset here.
4. In sctp_process_strreset_resp(), SCTP_STREAM_RESET_INCOMING_SSN or
OUTGOING event should always be sent for stream reset requests, no
matter it fails or succeeds to process the request.
Fixes: 810544764536 ("sctp: implement receiver-side procedures for the Outgoing SSN Reset Request Parameter")
Fixes: 16e1a91965b0 ("sctp: implement receiver-side procedures for the Incoming SSN Reset Request Parameter")
Fixes: 11ae76e67a17 ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip l add dev tun type gretap key 1000
ip a a dev tun 10.0.0.1/24
Packets with tun-id 1000 can be recived by tun dev. But packet can't
be sent through dev tun for non-tunnel-dst
With this patch: tunnel-dst can be get through lwtunnel like beflow:
ip r a 10.0.0.7 encap ip dst 172.168.0.11 dev tun
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot found that ax25 routes where not properly protected
against concurrent use [1].
In this particular report the bug happened while
copying ax25->digipeat.
Fix this problem by making sure we call ax25_get_route()
while ax25_route_lock is held, so that no modification
could happen while using the route.
The current two ax25_get_route() callers do not sleep,
so this change should be fine.
Once we do that, ax25_get_route() no longer needs to
grab a reference on the found route.
[1]
ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
BUG: KASAN: use-after-free in memcpy include/linux/string.h:352 [inline]
BUG: KASAN: use-after-free in kmemdup+0x42/0x60 mm/util.c:113
Read of size 66 at addr ffff888066641a80 by task syz-executor2/531
ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
CPU: 1 PID: 531 Comm: syz-executor2 Not tainted 5.0.0-rc2+ #10
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1db/0x2d0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x123/0x190 mm/kasan/generic.c:191
memcpy+0x24/0x50 mm/kasan/common.c:130
memcpy include/linux/string.h:352 [inline]
kmemdup+0x42/0x60 mm/util.c:113
kmemdup include/linux/string.h:425 [inline]
ax25_rt_autobind+0x25d/0x750 net/ax25/ax25_route.c:424
ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1224
__sys_connect+0x357/0x490 net/socket.c:1664
__do_sys_connect net/socket.c:1675 [inline]
__se_sys_connect net/socket.c:1672 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1672
do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458099
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f870ee22c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458099
RDX: 0000000000000048 RSI: 0000000020000080 RDI: 0000000000000005
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f870ee236d4
R13: 00000000004be48e R14: 00000000004ce9a8 R15: 00000000ffffffff
Allocated by task 526:
save_stack+0x45/0xd0 mm/kasan/common.c:73
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc mm/kasan/common.c:496 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:469
kasan_kmalloc+0x9/0x10 mm/kasan/common.c:504
ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
kmem_cache_alloc_trace+0x151/0x760 mm/slab.c:3609
kmalloc include/linux/slab.h:545 [inline]
ax25_rt_add net/ax25/ax25_route.c:95 [inline]
ax25_rt_ioctl+0x3b9/0x1270 net/ax25/ax25_route.c:233
ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
sock_do_ioctl+0xe2/0x400 net/socket.c:950
sock_ioctl+0x32f/0x6c0 net/socket.c:1074
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
Freed by task 550:
save_stack+0x45/0xd0 mm/kasan/common.c:73
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:458
kasan_slab_free+0xe/0x10 mm/kasan/common.c:466
__cache_free mm/slab.c:3487 [inline]
kfree+0xcf/0x230 mm/slab.c:3806
ax25_rt_add net/ax25/ax25_route.c:92 [inline]
ax25_rt_ioctl+0x304/0x1270 net/ax25/ax25_route.c:233
ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
sock_do_ioctl+0xe2/0x400 net/socket.c:950
sock_ioctl+0x32f/0x6c0 net/socket.c:1074
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff888066641a80
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 0 bytes inside of
96-byte region [ffff888066641a80, ffff888066641ae0)
The buggy address belongs to the page:
page:ffffea0001999040 count:1 mapcount:0 mapping:ffff88812c3f04c0 index:0x0
flags: 0x1fffc0000000200(slab)
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
raw: 01fffc0000000200 ffffea0001817948 ffffea0002341dc8 ffff88812c3f04c0
raw: 0000000000000000 ffff888066641000 0000000100000020 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888066641980: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
ffff888066641a00: 00 00 00 00 00 00 00 00 02 fc fc fc fc fc fc fc
>ffff888066641a80: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
^
ffff888066641b00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
ffff888066641b80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This message gets logged far too often for how interesting is it.
Most distributions nowadays configure NetworkManager to use randomly
generated MAC addresses for Wi-Fi network scans. The interfaces end up
being periodically brought down for the address change. When they're
subsequently brought back up, the message is logged, eventually flooding
the log.
Perhaps the message is not all that helpful: it seems to be more
interesting to hear when the addrconf actually start, not when it does
not. Let's lower its level.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-By: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in6_dump_addrs() returns a positive 1 if there was nothing to dump.
This return value can not be passed as return from inet6_dump_addr()
as is, because it will confuse rtnetlink, resulting in NLMSG_DONE
never getting set:
$ ip addr list dev lo
EOF on netlink
Dump terminated
v2: flip condition to avoid a new goto (DaveA)
Fixes: 7c1e8a3817c5 ("netlink: fixup regression in RTM_GETADDR")
Reported-by: Brendan Galloway <brendan.galloway@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ERSPAN key header field as tunnel key in gre_parse_header routine
since ERSPAN protocol sets the key field of the external GRE header to
0 resulting in a tunnel lookup fail in ip6gre_err.
In addition remove key field parsing and pskb_may_pull check in
erspan_rcv and ip6erspan_rcv
Fixes: 5a963eb61b7c ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup()
when the conversion into ktime multiplies the given value with NSEC_PER_USEC
(1000).
Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2
Add a check for the given tv_usec, so that the value stays below one second.
Additionally limit the tv_sec value to a reasonable value for CAN related
use-cases of 400 days and ensure all values to be positive.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26
Tested-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
con_fault() can transition the connection into STANDBY right after
ceph_con_keepalive() clears STANDBY in clear_standby():
libceph user thread ceph-msgr worker
ceph_con_keepalive()
mutex_lock(&con->mutex)
clear_standby(con)
mutex_unlock(&con->mutex)
mutex_lock(&con->mutex)
con_fault()
...
if KEEPALIVE_PENDING isn't set
set state to STANDBY
...
mutex_unlock(&con->mutex)
set KEEPALIVE_PENDING
set WRITE_PENDING
This triggers warnings in clear_standby() when either ceph_con_send()
or ceph_con_keepalive() get to clearing STANDBY next time.
I don't see a reason to condition queue_con() call on the previous
value of KEEPALIVE_PENDING, so move the setting of KEEPALIVE_PENDING
into the critical section -- unlike WRITE_PENDING, KEEPALIVE_PENDING
could have been a non-atomic flag.
Reported-by: syzbot+acdeb633f6211ccdf886@syzkaller.appspotmail.com
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Myungho Jung <mhjungk@gmail.com>
|
|
Pull networking fixes from David Miller:
1) Fix endless loop in nf_tables, from Phil Sutter.
2) Fix cross namespace ip6_gre tunnel hash list corruption, from
Olivier Matz.
3) Don't be too strict in phy_start_aneg() otherwise we might not allow
restarting auto negotiation. From Heiner Kallweit.
4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.
5) Memory leak in act_tunnel_key, from Davide Caratti.
6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.
7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.
8) Missing udplite rehash callbacks, from Alexey Kodanev.
9) Log dirty pages properly in vhost, from Jason Wang.
10) Use consume_skb() in neigh_probe() as this is a normal free not a
drop, from Yang Wei. Likewise in macvlan_process_broadcast().
11) Missing device_del() in mdiobus_register() error paths, from Thomas
Petazzoni.
12) Fix checksum handling of short packets in mlx5, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
bpf: in __bpf_redirect_no_mac pull mac only if present
virtio_net: bulk free tx skbs
net: phy: phy driver features are mandatory
isdn: avm: Fix string plus integer warning from Clang
net/mlx5e: Fix cb_ident duplicate in indirect block register
net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
net/mlx5e: Fix wrong error code return on FEC query failure
net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
tools: bpftool: Cleanup license mess
bpf: fix inner map masking to prevent oob under speculation
bpf: pull in pkt_sched.h header for tooling to fix bpftool build
selftests: forwarding: Add a test case for externally learned FDB entries
selftests: mlxsw: Test FDB offload indication
mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
net: bridge: Mark FDB entries that were added by user as such
mlxsw: spectrum_fid: Update dummy FID index
mlxsw: pci: Return error on PCI reset timeout
mlxsw: pci: Increase PCI SW reset timeout
mlxsw: pci: Ring CQ's doorbell before RDQ's
MAINTAINERS: update email addresses of liquidio driver maintainers
...
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2019-01-20
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a out-of-bounds access in __bpf_redirect_no_mac, from Willem.
2) Fix bpf_setsockopt to reset sock dst on SO_MARK changes, from Peter.
3) Fix map in map masking to prevent out-of-bounds access under
speculative execution, from Daniel.
4) Fix bpf_setsockopt's SO_MAX_PACING_RATE to support TCP internal
pacing, from Yuchung.
5) Fix json writer license in bpftool, from Thomas.
6) Fix AF_XDP to check if an actually queue exists during umem
setup, from Krzysztof.
7) Several fixes to BPF stackmap's build id handling. Another fix
for bpftool build to account for libbfd variations wrt linking
requirements, from Stanislav.
8) Fix BPF samples build with clang by working around missing asm
goto, from Yonghong.
9) Fix libbpf to retry program load on signal interrupt, from Lorenz.
10) Various minor compile warning fixes in BPF code, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzkaller was able to construct a packet of negative length by
redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline]
BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
memcpy+0x23/0x50 mm/kasan/kasan.c:302
memcpy include/linux/string.h:345 [inline]
skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
__pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
__pskb_copy include/linux/skbuff.h:1053 [inline]
pskb_copy include/linux/skbuff.h:2904 [inline]
skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539
ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline]
sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029
__netdev_start_xmit include/linux/netdevice.h:4325 [inline]
netdev_start_xmit include/linux/netdevice.h:4334 [inline]
xmit_one net/core/dev.c:3219 [inline]
dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235
__dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805
dev_queue_xmit+0x17/0x20 net/core/dev.c:3838
__bpf_tx_skb net/core/filter.c:2016 [inline]
__bpf_redirect_common net/core/filter.c:2054 [inline]
__bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061
____bpf_clone_redirect net/core/filter.c:2094 [inline]
bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066
bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000
The generated test constructs a packet with mac header, network
header, skb->data pointing to network header and skb->len 0.
Redirecting to a sit0 through __bpf_redirect_no_mac pulls the
mac length, even though skb->data already is at skb->network_header.
bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2.
Update the offset calculation to pull only if skb->data differs
from skb->network_header, which is not true in this case.
The test itself can be run only from commit 1cf1cae963c2 ("bpf:
introduce BPF_PROG_TEST_RUN command"), but the same type of packets
with skb at network header could already be built from lwt xmit hooks,
so this fix is more relevant to that commit.
Also set the mac header on redirect from LWT_XMIT, as even after this
change to __bpf_redirect_no_mac that field is expected to be set, but
is not yet in ip_finish_output2.
Fixes: 3a0af8fd61f9 ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pull NFS client fixes from Anna Schumaker:
"These are mostly fixes for SUNRPC bugs, with a single v4.2
copy_file_range() fix mixed in.
Stable bugfixes:
- Fix TCP receive code on archs with flush_dcache_page()
Other bugfixes:
- Fix error code in rpcrdma_buffer_create()
- Fix a double free in rpcrdma_send_ctxs_create()
- Fix kernel BUG at kernel/cred.c:825
- Fix unnecessary retry in nfs42_proc_copy_file_range()
- Ensure rq_bytes_sent is reset before request transmission
- Ensure we respect the RPCSEC_GSS sequence number limit
- Address Kerberos performance/behavior regression"
* tag 'nfs-for-5.0-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Address Kerberos performance/behavior regression
SUNRPC: Ensure we respect the RPCSEC_GSS sequence number limit
SUNRPC: Ensure rq_bytes_sent is reset before request transmission
NFSv4.2 fix unnecessary retry in nfs4_copy_file_range
sunrpc: kernel BUG at kernel/cred.c:825!
SUNRPC: Fix TCP receive code on archs with flush_dcache_page()
xprtrdma: Double free in rpcrdma_sendctxs_create()
xprtrdma: Fix error code in rpcrdma_buffer_create()
|
|
In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl'
counter when we decrement the ttl to zero. For unicast frames
destined for other hosts, we stop processing the frame at that point.
For multicast frames, we do not rebroadcast it in this case, but we
do pass the frame up the stack to process it on this STA. That
doesn't match the usual definition of "dropped," so don't count
those as such.
With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a
peer in a ttl=1 network no longer increments the counter rapidly.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.
In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.
The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.
Fixes: 816a3bed9549 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660dd ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit cb9f1b783850, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:
Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
TX: bytes packets errors dropped carrier collsns
0 0 1 0 0 0
The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).
This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/
Fixes: cb9f1b783850 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If sch_fq packet scheduler is not used, TCP can fallback to
internal pacing, but this requires sk_pacing_status to
be properly set.
Fixes: 8c4b4c7e9ff0 ("bpf: Add setsockopt helper function to bpf")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In sock_setsockopt() (net/core/sock.h), when SO_MARK option is used
to change sk_mark, sk_dst_reset(sk) is called. The same should be
done in bpf_setsockopt().
Fixes: 8c4b4c7e9ff0 ("bpf: Add setsockopt helper function to bpf")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
After commit 23b0269e58ae ("net: udp6: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.
This is related to the problem addressed in the commit 719f835853a9
("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now
looks for a socket immediately in the secondary hash table.
And this issue was found with LTP/network tests as well.
Fixes: 23b0269e58ae ("net: udp6: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 4cdeeee9252a ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.
This is related to the problem addressed in the commit 719f835853a9
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.
The issue was found with LTP/network tests (UDP-Lite test-cases).
Fixes: 4cdeeee9252a ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes (especially 05cd271fd61a ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.
v2:
- use kzalloc() instead of kcalloc()
Fixes: 05cd271fd61a ("cls_flower: Support multiple masks per priority")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warnings (W=1).
To preserve as much of the existing comment only change a ‘:’ into a ‘,’.
This is enough change, to match the regular expression expected by GCC.
This commit removes the following warning:
net/core/filter.c:5310:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Failure __ip_append_data triggers udp_flush_pending_frames, but these
tests happen later. The skb must be freed directly.
Fixes: bec1f6f697362 ("udp: generate gso with UDP_SEGMENT")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The section of bpfilter UMH blob is the ".bpfilter_umh". but this is not
an explicit section. so linking warning occurred at compile time for the
powerpc.
So, this patch makes use of the ".rodata" instead of the ".bpfilter_umh".
Config condition:
CONFIG_BPFILTER=y
CONFIG_BPFILTER_UMH=y
Result:
ld: warning: orphan section `.bpfilter_umh' from
`net/bpfilter/bpfilter_umh_blob.o' being placed in section `.bpfilter_umh'
Fixes: 61fbf5933d42 ("net: bpfilter: restart bpfilter_umh when error occurred")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"IPv6: " prefix is already added by pr_fmt, no need to include
it again in the pr_warn() format. The message predates extack
support, we can replace the whole thing with an extack message.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This should be 1 for normal allocations, 0 disables leak reporting.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Fixes: 85704cb8dcfd ("net/core/neighbour: tell kmemleak about hash tables")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The similar issue as fixed in Commit 4a2eb0c37b47 ("sctp: initialize
sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists
in sctp_inetaddr_event, as Alexander noticed.
To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp
ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist().
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reported-by: syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As said in draft-foschiano-erspan-03#section4:
Different frame variants known as "ERSPAN Types" can be
distinguished based on the GRE "Protocol Type" field value: Type I
and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].
So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().
Fixes: 94d7d8f29287 ("ip6_gre: add erspan v2 support")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For nested and variable attributes, the expected length of an attribute
is not known and marked by a negative number. This results in an OOB
read when the expected length is later used to check if the attribute is
all zeros. Fix this by using the actual length of the attribute rather
than the expected length.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martin reported a set of filters don't work after changing
from reclassify to continue. Looking into the code, it
looks like skb protocol is not always fetched for each
iteration of the filters. But, as demonstrated by Martin,
TC actions could modify skb->protocol, for example act_vlan,
this means we have to refetch skb protocol in each iteration,
rather than using the one we fetch in the beginning of the loop.
This bug is _not_ introduced by commit 3b3ae880266d
("net: sched: consolidate tc_classify{,_compat}"), technically,
if act_vlan is the only action that modifies skb protocol, then
it is commit c7e2b9689ef8 ("sched: introduce vlan action") which
introduced this bug.
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both gue_err() and gue6_err() incorrectly assume
linear skbs. Fix them to use pskb_may_pull().
BUG: KMSAN: uninit-value in gue6_err+0x475/0xc40 net/ipv6/fou6.c:101
CPU: 0 PID: 18083 Comm: syz-executor1 Not tainted 5.0.0-rc1+ #7
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:600
__msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313
gue6_err+0x475/0xc40 net/ipv6/fou6.c:101
__udp6_lib_err_encap_no_sk net/ipv6/udp.c:434 [inline]
__udp6_lib_err_encap net/ipv6/udp.c:491 [inline]
__udp6_lib_err+0x18d0/0x2590 net/ipv6/udp.c:522
udplitev6_err+0x118/0x130 net/ipv6/udplite.c:27
icmpv6_notify+0x462/0x9f0 net/ipv6/icmp.c:784
icmpv6_rcv+0x18ac/0x3fa0 net/ipv6/icmp.c:872
ip6_protocol_deliver_rcu+0xb5a/0x23a0 net/ipv6/ip6_input.c:394
ip6_input_finish net/ipv6/ip6_input.c:434 [inline]
NF_HOOK include/linux/netfilter.h:289 [inline]
ip6_input+0x2b6/0x350 net/ipv6/ip6_input.c:443
dst_input include/net/dst.h:450 [inline]
ip6_rcv_finish+0x4e7/0x6d0 net/ipv6/ip6_input.c:76
NF_HOOK include/linux/netfilter.h:289 [inline]
ipv6_rcv+0x34b/0x3f0 net/ipv6/ip6_input.c:272
__netif_receive_skb_one_core net/core/dev.c:4973 [inline]
__netif_receive_skb net/core/dev.c:5083 [inline]
process_backlog+0x756/0x10e0 net/core/dev.c:5923
napi_poll net/core/dev.c:6346 [inline]
net_rx_action+0x78b/0x1a60 net/core/dev.c:6412
__do_softirq+0x53f/0x93a kernel/softirq.c:293
do_softirq_own_stack+0x49/0x80 arch/x86/entry/entry_64.S:1039
</IRQ>
do_softirq kernel/softirq.c:338 [inline]
__local_bh_enable_ip+0x16f/0x1a0 kernel/softirq.c:190
local_bh_enable+0x36/0x40 include/linux/bottom_half.h:32
rcu_read_unlock_bh include/linux/rcupdate.h:696 [inline]
ip6_finish_output2+0x1d64/0x25f0 net/ipv6/ip6_output.c:121
ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154
NF_HOOK_COND include/linux/netfilter.h:278 [inline]
ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171
dst_output include/net/dst.h:444 [inline]
ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176
ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727
udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169
udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466
inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116
__sys_sendmmsg+0x580/0xad0 net/socket.c:2211
__do_sys_sendmmsg net/socket.c:2240 [inline]
__se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237
__x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x457ec9
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f4a5204fc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000000457ec9
RDX: 00000000040001ab RSI: 0000000020000240 RDI: 0000000000000003
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4a520506d4
R13: 00000000004c4ce5 R14: 00000000004d85d8 R15: 00000000ffffffff
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:205 [inline]
kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:159
kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176
kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185
slab_post_alloc_hook mm/slab.h:446 [inline]
slab_alloc_node mm/slub.c:2754 [inline]
__kmalloc_node_track_caller+0xe9e/0xff0 mm/slub.c:4377
__kmalloc_reserve net/core/skbuff.c:140 [inline]
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
alloc_skb_with_frags+0x1c7/0xac0 net/core/skbuff.c:5288
sock_alloc_send_pskb+0xafd/0x10a0 net/core/sock.c:2091
sock_alloc_send_skb+0xca/0xe0 net/core/sock.c:2108
__ip6_append_data+0x42ed/0x5dc0 net/ipv6/ip6_output.c:1443
ip6_append_data+0x3c2/0x650 net/ipv6/ip6_output.c:1619
icmp6_send+0x2f5c/0x3c40 net/ipv6/icmp.c:574
icmpv6_send+0xe5/0x110 net/ipv6/ip6_icmp.c:43
ip6_link_failure+0x5c/0x2c0 net/ipv6/route.c:2231
dst_link_failure include/net/dst.h:427 [inline]
vti_xmit net/ipv4/ip_vti.c:229 [inline]
vti_tunnel_xmit+0xf3b/0x1ea0 net/ipv4/ip_vti.c:265
__netdev_start_xmit include/linux/netdevice.h:4382 [inline]
netdev_start_xmit include/linux/netdevice.h:4391 [inline]
xmit_one net/core/dev.c:3278 [inline]
dev_hard_start_xmit+0x604/0xc40 net/core/dev.c:3294
__dev_queue_xmit+0x2e48/0x3b80 net/core/dev.c:3864
dev_queue_xmit+0x4b/0x60 net/core/dev.c:3897
neigh_direct_output+0x42/0x50 net/core/neighbour.c:1511
neigh_output include/net/neighbour.h:508 [inline]
ip6_finish_output2+0x1d4e/0x25f0 net/ipv6/ip6_output.c:120
ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154
NF_HOOK_COND include/linux/netfilter.h:278 [inline]
ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171
dst_output include/net/dst.h:444 [inline]
ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176
ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727
udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169
udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466
inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116
__sys_sendmmsg+0x580/0xad0 net/socket.c:2211
__do_sys_sendmmsg net/socket.c:2240 [inline]
__se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237
__x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of
the connection and so transitions this socket to CLOSE_WAIT state.
Transmission in close wait state is acceptable. Other similar tests in
the stack (e.g., in FastOpen) accept both states. Relax this test, too.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html
Fixes: f214f915e7db ("tcp: enable MSG_ZEROCOPY")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
CC: Yuchung Cheng <ycheng@google.com>
CC: Neal Cardwell <ncardwell@google.com>
CC: Soheil Hassas Yeganeh <soheil@google.com>
CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
running the following TDC test cases:
7afc - Replace tunnel_key set action with all parameters
364d - Replace tunnel_key set action with all parameters and cookie
it's possible to trigger kmemleak warnings like:
unreferenced object 0xffff94797127ab40 (size 192):
comm "tc", pid 3248, jiffies 4300565293 (age 1006.862s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 c0 93 f9 8a ff ff ff ff ................
41 84 ee 89 ff ff ff ff 00 00 00 00 00 00 00 00 A...............
backtrace:
[<000000001e85b61c>] tunnel_key_init+0x31d/0x820 [act_tunnel_key]
[<000000007f3f6ee7>] tcf_action_init_1+0x384/0x4c0
[<00000000e89e3ded>] tcf_action_init+0x12b/0x1a0
[<00000000c1c8c0f8>] tcf_action_add+0x73/0x170
[<0000000095a9fc28>] tc_ctl_action+0x122/0x160
[<000000004bebeac5>] rtnetlink_rcv_msg+0x263/0x2d0
[<000000009fd862dd>] netlink_rcv_skb+0x4a/0x110
[<00000000b55199e7>] netlink_unicast+0x1a0/0x250
[<000000004996cd21>] netlink_sendmsg+0x2c1/0x3c0
[<000000004d6a94b4>] sock_sendmsg+0x36/0x40
[<000000005d9f0208>] ___sys_sendmsg+0x280/0x2f0
[<00000000dec19023>] __sys_sendmsg+0x5e/0xa0
[<000000004b82ac81>] do_syscall_64+0x5b/0x180
[<00000000a0f1209a>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<000000002926b2ab>] 0xffffffffffffffff
when the tunnel_key action is replaced, the kernel forgets to release the
dst metadata: ensure they are released by tunnel_key_init(), the same way
it's done in tunnel_key_release().
Fixes: d0f6dd8a914f4 ("net/sched: Introduce act_tunnel_key")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The changes introduced to allow rxrpc calls to be retried creates an issue
when it comes to refcounting afs_call structs. The problem is that when
rxrpc_send_data() queues the last packet for an asynchronous call, the
following sequence can occur:
(1) The notify_end_tx callback is invoked which causes the state in the
afs_call to be changed from AFS_CALL_CL_REQUESTING or
AFS_CALL_SV_REPLYING.
(2) afs_deliver_to_call() can then process event notifications from rxrpc
on the async_work queue.
(3) Delivery of events, such as an abort from the server, can cause the
afs_call state to be changed to AFS_CALL_COMPLETE on async_work.
(4) For an asynchronous call, afs_process_async_call() notes that the call
is complete and tried to clean up all the refs on async_work.
(5) rxrpc_send_data() might return the amount of data transferred
(success) or an error - which could in turn reflect a local error or a
received error.
Synchronising the clean up after rxrpc_kernel_send_data() returns an error
with the asynchronous cleanup is then tricky to get right.
Mostly revert commit c038a58ccfd6704d4d7d60ed3d6a0fca13cf13a4. The two API
functions the original commit added aren't currently used. This makes
rxrpc_kernel_send_data() always return successfully if it queued the data
it was given.
Note that this doesn't affect synchronous calls since their Rx notification
function merely pokes a wait queue and does not refcounting. The
asynchronous call notification function *has* to do refcounting and pass a
ref over the work item to avoid the need to sync the workqueue in call
cleanup.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BUG: KMSAN: uninit-value in tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
CPU: 0 PID: 4514 Comm: syz-executor485 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
tipc_nl_compat_recv+0x164b/0x2700 net/tipc/netlink_compat.c:1153
genl_family_rcv_msg net/netlink/genetlink.c:599 [inline]
genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624
netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447
genl_rcv+0x63/0x80 net/netlink/genetlink.c:635
netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline]
netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337
netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x43fda9
RSP: 002b:00007ffd0c184ba8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fda9
RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 00000000004002c8 R11: 0000000000000213 R12: 00000000004016d0
R13: 0000000000401760 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2737 [inline]
__kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:984 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline]
netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
In tipc_nl_compat_recv(), when the len variable returned by
nlmsg_attrlen() is 0, the message is still treated as a valid one,
which is obviously unresonable. When len is zero, it means the
message not only doesn't contain any valid TLV payload, but also
TLV header is not included. Under this stituation, tlv_type field
in TLV header is still accessed in tipc_nl_compat_dumpit() or
tipc_nl_compat_doit(), but the field space is obviously illegal.
Of course, it is not initialized.
Reported-by: syzbot+bca0dc46634781f08b38@syzkaller.appspotmail.com
Reported-by: syzbot+6bdb590321a7ae40c1a6@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported:
BUG: KMSAN: uninit-value in __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline]
BUG: KMSAN: uninit-value in __fswab32 include/uapi/linux/swab.h:59 [inline]
BUG: KMSAN: uninit-value in tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826
CPU: 0 PID: 6290 Comm: syz-executor848 Not tainted 4.19.0-rc8+ #70
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x306/0x460 lib/dump_stack.c:113
kmsan_report+0x1a2/0x2e0 mm/kmsan/kmsan.c:917
__msan_warning+0x7c/0xe0 mm/kmsan/kmsan_instr.c:500
__arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline]
__fswab32 include/uapi/linux/swab.h:59 [inline]
tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826
__tipc_nl_compat_dumpit+0x59e/0xdb0 net/tipc/netlink_compat.c:205
tipc_nl_compat_dumpit+0x63a/0x820 net/tipc/netlink_compat.c:270
tipc_nl_compat_handle net/tipc/netlink_compat.c:1151 [inline]
tipc_nl_compat_recv+0x1402/0x2760 net/tipc/netlink_compat.c:1210
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185c/0x1a20 net/netlink/genetlink.c:626
netlink_rcv_skb+0x394/0x640 net/netlink/af_netlink.c:2454
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x166d/0x1720 net/netlink/af_netlink.c:1343
netlink_sendmsg+0x1391/0x1420 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xe47/0x1200 net/socket.c:2116
__sys_sendmsg net/socket.c:2154 [inline]
__do_sys_sendmsg net/socket.c:2163 [inline]
__se_sys_sendmsg+0x307/0x460 net/socket.c:2161
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161
do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x440179
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffecec49318 EFLAGS: 00000213 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440179
RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8
R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000401a00
R13: 0000000000401a90 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:255 [inline]
kmsan_internal_poison_shadow+0xc8/0x1d0 mm/kmsan/kmsan.c:180
kmsan_kmalloc+0xa4/0x120 mm/kmsan/kmsan_hooks.c:104
kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:113
slab_post_alloc_hook mm/slab.h:446 [inline]
slab_alloc_node mm/slub.c:2727 [inline]
__kmalloc_node_track_caller+0xb43/0x1400 mm/slub.c:4360
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x422/0xe90 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:996 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline]
netlink_sendmsg+0xcaf/0x1420 net/netlink/af_netlink.c:1883
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xe47/0x1200 net/socket.c:2116
__sys_sendmsg net/socket.c:2154 [inline]
__do_sys_sendmsg net/socket.c:2163 [inline]
__se_sys_sendmsg+0x307/0x460 net/socket.c:2161
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161
do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
We cannot take for granted the thing that the length of data contained
in TLV is longer than the size of struct tipc_name_table_query in
tipc_nl_compat_name_table_dump().
Reported-by: syzbot+06e771a754829716a327@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reports following splat:
BUG: KMSAN: uninit-value in strlen+0x3b/0xa0 lib/string.c:486
CPU: 1 PID: 9306 Comm: syz-executor172 Not tainted 4.20.0-rc7+ #2
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613
__msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313
strlen+0x3b/0xa0 lib/string.c:486
nla_put_string include/net/netlink.h:1154 [inline]
__tipc_nl_compat_link_set net/tipc/netlink_compat.c:708 [inline]
tipc_nl_compat_link_set+0x929/0x1220 net/tipc/netlink_compat.c:744
__tipc_nl_compat_doit net/tipc/netlink_compat.c:311 [inline]
tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:344
tipc_nl_compat_handle net/tipc/netlink_compat.c:1107 [inline]
tipc_nl_compat_recv+0x14d7/0x2760 net/tipc/netlink_compat.c:1210
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626
netlink_rcv_skb+0x444/0x640 net/netlink/af_netlink.c:2477
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf40/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116
__sys_sendmsg net/socket.c:2154 [inline]
__do_sys_sendmsg net/socket.c:2163 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2161
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
The uninitialised access happened in
nla_put_string(skb, TIPC_NLA_LINK_NAME, lc->name)
This is because lc->name string is not validated before it's used.
Reported-by: syzbot+d78b8a29241a195aefb8@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Linus Torvalds
David S. Miller
Chaitanya Tata
Chaitanya Tata
Mathieu Malaterre
Balaji Pothunoori
Johannes Berg
Xin Long
wenxu
Eric Dumazet
Lubomir Rintel
Jakub Kicinski
Lorenzo Bianconi
Oliver Hartkopp
Ilya Dryomov
Willem de Bruijn
Bob Copeland
Ido Schimmel
Ross Lagerwall
Yang Wei
Yunjian Wang
Nicolas Dichtel
Yuchung Cheng
Peter Oskolkov
Alexey Kodanev
Ivan Vecera
Taehee Yoo
Konstantin Khlebnikov
Cong Wang
Davide Caratti
David Howells
Ying Xue