aboutsummaryrefslogtreecommitdiffstats
path: root/security (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2017-08-28ARM: dts: uniphier: fix size of sdctrl nodesMasahiro Yamada2-2/+2
All registers are located within 0x400 size from the base address. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-28ARM: dts: uniphier: add AIDET nodesMasahiro Yamada5-0/+35
Add UniPhier AIDET (ARM Interrupt Detector) nodes to support active low interrupts. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-28arm: dts: sunxi: Revert EMAC changesMaxime Ripard10-128/+0
Since the discussion is not settled yet for the EMAC, and that the release in getting really close, let's revert the changes for now, and we'll reintroduce them later. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-28arm64: dts: allwinner: Revert EMAC changesMaxime Ripard8-135/+0
Since the discussion is not settled yet for the EMAC, and that the release in getting really close, let's revert the changes for now, and we'll reintroduce them later. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-28dt-bindings: net: Revert sun8i dwmac bindingMaxime Ripard1-84/+0
This binding still doesn't please everyone, and we're getting far too close from the release to allow it to reach a stable version. Let's remove it until the discussion settles down. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-28Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"Maxime Ripard1-8/+1
This reverts commit ddb56254ae52acff7bd7fbd8f963e79bffc324d4. The EMAC bindings have not stabilized yet, so we can't commit to keeping them stable. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-23ARM: dts: rockchip: enable usb for rv1108-evbFrank Wang1-0/+24
Rockchip's rv1108-evb board has one usb otg controller and one usb host controller, each usb controller connect with one usb-phy port through UTMI+ interface. This patch enables them to support usb on rv1108-evb board. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-23ARM: dts: rockchip: add usb nodes for rv1108 SoCsFrank Wang1-1/+72
This patch adds usb otg/host controllers and phys nodes for RV1108 SoCs. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-23dt-bindings: update grf-binding for rv1108 SoCsFrank Wang1-0/+3
This patch adds the compatible of GRF and USBGRF for RV1108 SoCs. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-23ARM: dts: aspeed-g4: fix AHB window size of the SMC controllersCédric Le Goater1-2/+2
The window of the Aspeed AST2400 SMC Controllers to map chips on the AHB Bus has a 256MB size. The full window range is [ 0x20000000 - 0x2FFFFFFF ] for the FMC controller [ 0x30000000 - 0x3FFFFFFF ] for the SPI controller This change requires CONFIG_VMSPLIT_2G to be set. Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Joel Stanley <joel@jms.id.au>
2017-08-23ARM: dts: rockchip: add cpu power supply for rv1108 evbAndy Yan1-0/+4
The cpu is powered by regulator vdd_core on RV1108 evalution board. Add it to the cpu dt node. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-23ARM: dts: rockchip: add cpu opp table for rv1108Andy Yan1-0/+27
Add cpu opp table for rv1108 to support frequency from 408MHZ to 1008MHZ. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-22ARM: dts: augment Ux500 to use DT cpufreqLinus Walleij1-7/+8
This adds the operating points to the Ux500 device tree and deletes the old special-purpose cpufreq node, as we can now use the generic DT cpufreq driver. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-08-21ARM: dts: rockchip: add rk322x iommu nodesSimon Xue1-0/+36
Add VPU/VDEC/VOP/IEP iommu nodes Signed-off-by: Simon Xue <xxm@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-21arm: zynq: Remove earlycon from bootargsMichal Simek5-5/+5
Earlyconsole is used for early kernel debugging that's why this option shouldn't be enabled by default. Earlyconsole is partially copying the part of the bootlog after "bootconsole [uart0] disabled". Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-21arm: zynq: Use C pre-processor for includes in dtsMichal Simek4-4/+4
Change the dtsi include code to use the C pre-processor #include instead of the device tree /include/. This brings all Zynq device trees inline with each other. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-21arm: zynq: Label whole PL part as fpga_full regionMichal Simek1-0/+8
This will simplify dt overlay structure for the whole PL. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-21arm: zynq: Add device-type property for zynq ethernet phy nodesSai Pavan Boddu5-0/+5
Mention device-type = "ethernet-phy", as qemu will need this in absence of compatible. Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-21arm: zynq: Add adv7511 on i2c bus for zc70xChristian Kohn2-0/+30
Describe adv7511 on i2c bus. Signed-off-by: Christian Kohn <christian.kohn@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-21ARM: dts: da850-lego-ev3: Add node for LCD displayDavid Lechner1-0/+24
This adds a new node for the LEGO MINDSTORMS EV3 LCD display. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2017-08-21ARM: dts: rockchip: add accelerometer bma250e dt node for rv1108 evbAndy Yan1-0/+7
Add dt node of bosch accelerometer bma250e on rv1108 evb. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-21ARM: dts: rockchip: add pmic rk805 dt node for rv1108 evbAndy Yan1-0/+108
RK805 is used as the voltage regulator on rv1108 evaluation board. Add device tree node for it. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-19ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi BPI-M3Chen-Yu Tsai2-0/+149
The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family. It is roughly the same form factor as the BPI-M1+, with roughly the same peripherals and connectors: - 2GB LPDDR3 DRAM - 8GB eMMC - Micro-SD card slot - HDMI output - Headset (stereo + mic) jack - Onboard mic - Gigabit Ethernet with RTL8211E transceiver - Ampak AP6212 WiFi + BT - USB OTG connector - USB-to-SATA bridge connected through a USB 2.0 hub - Consumer IR receiver - MIPI DSI LCD panel connector - Camera interface (parallel and MIPI CSI) connector - 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB) - Raspberry Pi 2 compatible GPIO header Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2017-08-19ARM: dts: rockchip: add pwm backlight for rv1108 evbAndy Yan1-0/+43
RV1108 EVB uses pwm0 modulate the backlight, add dt node to enable it. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-19ARM: dts: rockchip: add pwm dt nodes for rv1108Andy Yan1-0/+144
Add pwm device tree node for rv1108 soc Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-08-18ARM: dts: versatile: fix PCI bus dtc warningsRob Herring1-1/+1
dtc recently added PCI bus checks. Fix these warnings. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-08-18ARM: dts: spear13xx: fix PCI bus dtc warningsRob Herring2-0/+4
dtc recently added PCI bus checks. Fix these warnings. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-08-19ARM: sun8i: a83t: h8homlet-v2: Enable USB portsChen-Yu Tsai1-0/+29
The h8homlet board has the A83T's standard USB 1.1/2.0 host pair routed to a USB host port on the board. The other USB host port is routed to USB OTG controller. Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2017-08-19ARM: sun8i: a83t: cubietruck-plus: Enable onboard USB peripheralsChen-Yu Tsai1-5/+44
The Cubietruck-plus has a GL830 USB-to-SATA bridge connected to EHCI0, and a USB3503 HSIC USB 2.0 hub connected to EHCI1. The USB3503's I2C control interface is not connected. This patch enables both EHCI controllers, adds a device node for the USB hub, and includes sunxi-common-regulators.dtsi for the VBUS regulators. The existing reg_vcc3v3 is dropped as it is also available in the set of common regulators. Other unused regulators are disabled. Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2017-08-19ARM: sun8i: a83t: Add device node for USB OTG controllerChen-Yu Tsai1-0/+14
The USB OTG controller found on the A83T is compatible with the one found on the A33. Add a device node for it. Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2017-08-19ARM: sun8i: a83t: Add USB PHY and host device nodesChen-Yu Tsai1-0/+62
The A83T has 3 USB PHYs, 1 for USB OTG, 1 for standard USB 2.0, 1 for USB HSIC. EHCI0/OHCI0 are the standard USB host pair, while EHCI1 is the host controller for HSIC. OTG is not added yet. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-17ARM: BCM53573: Specify ports for USB LED for Tenda AC9Rafał Miłecki2-0/+6
This uses trigger-sources documented in commit 80dc6e1cd85fc ("dt-bindings: leds: document new trigger-sources property") to specify USB ports. Such an information can be used by operating system to setup LEDs behavior. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Add generic-ehci/ohci nodesRaveendra Padasalagi1-0/+14
Add dt nodes for generic-ehci/ohci host controller. Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphnScott Branden1-2/+5
Use serial0 alias to select stdout-path on Cygnus bcm911360_entphon board. Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Add additional peripherals to dtsiJonathan Richardson1-0/+102
Add nodes for peripherals in Cygnus dtsi: sdhci, keypad, spi, dma, pinmux configs. Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Enable Performance Monitoring UnitJason Uy1-0/+5
Add PMU capability to Cygnus so trace and performance profiling can be used. Signed-off-by: Jason Uy <jason.uy@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: place v3d in proper address ordered locationScott Branden1-13/+13
Move v3d devicetree node to proper address ordered location in Cygnus dtsi. Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Fix incorrect UART2 register baseRay Jui1-1/+1
Fix incorrect Cygnus UART2 register base. Fixes: 0f0b21a83ad2 ("ARM: dts: Move all Cygnus peripherals into axi bus") Signed-off-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpioAdam Ford1-1/+1
Fixes commit 687c27676151 ("ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit") This patch corrects an issue where the cd-gpios was improperly setup using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-17ARM: dts: am57xx-beagle-x15: Add support for rev CRobert Nelson2-0/+40
Latest update to the BeagleBoard-X15 platform (revision C). This board contains a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when running at 1000 Mbps speeds. This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom: [BBRDX15_C.001731PX150249] Rev C is now in full production and boards are available for end users. https://beagleboard.org/x15 https://github.com/beagleboard/beagleboard-x15/ Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Nishanth Menon <nm@ti.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Drew Fustini <drew@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-17ARM: tegra: Enable UDC on AC100Dmitry Osipenko1-0/+2
Override the compatible string of the first USB controller to enable device mode. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Tested-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: tegra: Enable UDC on Jetson TK1Thierry Reding1-1/+11
Override the compatible string of the first USB controller to enable device mode. Tested-by: Nicolas Chauvet <kwizart@gmail.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: tegra: Enable UDC on DalmoreThierry Reding1-0/+10
Override the compatible string of the first USB controller to enable device mode. Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: tegra: Enable UDC on BeaverThierry Reding1-0/+10
Override the compatible string of the first USB controller to enable device mode. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: dts: r8a7791: Use R-Car SATA Gen2 fallback compat stringSimon Horman1-2/+2
Use newly added R-Car SATA Gen2 fallback compat string in the DT of the r8a7791 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before the fallback compat string is considered. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-08-17ARM: dts: r8a7790: Use R-Car SATA Gen2 fallback compat stringSimon Horman1-2/+2
Use newly added R-Car SATA Gen2 fallback compat string in the DT of the r8a7790 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before the fallback compat string is considered. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-08-17ARM: dts: r8a7743: Add OPP table for frequency scalingBiju Das1-0/+9
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver. - clock-latency = 300 us Approximate worst-case latency to do clock transition for every OPPs. Using an arbitrary safe value similar to r8a7791(R-Car M2) Soc. - operating-points = < kHz - uV > List of 6 operating points. All of them are using the same voltage since DVS is not supported in RZ/G1 Soc. Note:This also fixes the below errors seen on kernel logs [ 0.876877] cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19) [ 0.883727] cpu cpu1: cpufreq_init: failed to get clk: -2 Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17ARM: dts: r8a7743: Add APMU node and second CPU coreBiju Das1-0/+16
Add DT nodes for the Advanced Power Management Unit (APMU) and the second CPU core. Use the enable-method to point out that the APMU should be used for SMP support. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17dt-bindings: apmu: Document r8a7743 supportBiju Das1-1/+2
Document APMU and SMP enable method for RZ/G1M (also known as r8a7743) SoC. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17ARM: shmobile: document iW-RainboW-G22D SODIMM SOM Development PlatformFabrizio Castro1-0/+2
Document the iW-RainboW-G22D device tree bindings. It is just a placeholder for the time being, the actual implementation is not available yet. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Chris Paterson <chris.paterson2@renesas.com> Reviewed-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.