| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This will be used by the regmap support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now let's take the basic tracepoints back to the HD-audio driver.
The three bus tracepoints, hda_send_cmd, hda_get_response and
hda_unsol_event are revived but in a slightly different form.
Since we don't assign the card number there, print the bus device name
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files. Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.
In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes. It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits. The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files. Each of these
attributes show a single value. The rest are the widget nodes
belonging to that AFG. Note that the child node might not start from
0x02 but from another value like 0x0a.
Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files. The caps (representing the widget
capability bits) always contain a value. The rest may contain
value(s) if the attribute exists on the node. Only connections file
show multiple values while other attributes have zero or one single
value.
An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/ 04/ 07/ 0a/ 0d/ 10/ 13/ 16/ 19/ 1c/ 1f/ 22/
02/ 05/ 08/ 0b/ 0e/ 11/ 14/ 17/ 1a/ 1d/ 20/ 23/
03/ 06/ 09/ 0c/ 0f/ 12/ 15/ 18/ 1b/ 1e/ 21/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps amp_out_caps power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps amp_out_caps caps connections pin_caps pin_cfg
power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
Takashi Iwai