| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There are bug reports of a crash with USB-audio devices when PCM
prepare is performed immediately after the stream is stopped via
trigger callback. It turned out that the problem is that we don't
wait until all URBs are killed.
This patch adds a new function to synchronize the pending stop
operation on an endpoint, and calls in the prepare callback for
avoiding the crash above.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=49181
Reported-and-tested-by: Artem S. Tashkinov <t.artem@lycos.com>
Cc: <stable@vger.kernel.org> [v3.6]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
cdc_eem frames might need to contain 802.1Q VLAN Ethernet frames.
URB/skb sizing from usbnet will default to the hard_mtu,
so account for the VLAN header by expanding that via hard_header_len
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Checking skb->len against ETH_FRAME_LEN assumes a 1514
ethernet frame size. With an 802.1Q VLAN header, ethernet
frame length can now be 1518. Validate frame length against that.
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
INGPADBOUNDARY_MASK is already shifted. No need to shift it again. On reloading
a driver it was resulting in a bad SGE FL MTU sizes [1536, 9088] error. This
only causes an issue on systems that have L1 cache size of 32B, 128B, 512B,
2048B or 4096B.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It doesn't make much sense to enable ISDN services if you don't
intend to connect to a network. Therefore insisting that ISDN
depends on NETDEVICES seems logical. We can then remove any
guards mentioning NETDEVICES inside all subordinate drivers.
This also has the nice side-effect of fixing the warning below
when ISDN_I4L && !CONFIG_NETDEVICES at compile time.
This patch fixes:
drivers/isdn/i4l/isdn_common.c: In function ‘isdn_ioctl’:
drivers/isdn/i4l/isdn_common.c:1278:8: warning: unused variable ‘s’ [-Wunused-variable]
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not assume reserve fields to be don't cares as fields may change.
Clearing data structures before using.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If host clock is disabled, host cannot detect a card in case of using
CD internal for detection.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Due to a NULL dereference, the following patch is causing oops
in normal trafic condition:
commit c0de08d04215031d68fa13af36f347a6cfa252ca
Author: Eric Leblond <eric@regit.org>
Date: Thu Aug 16 22:02:58 2012 +0000
af_packet: don't emit packet on orig fanout group
This buggy patch was a feature fix and has reached most stable
branches.
When skb->sk is NULL and when packet fanout is used, there is a
crash in match_fanout_group where skb->sk is accessed.
This patch fixes the issue by returning false as soon as the
socket is NULL: this correspond to the wanted behavior because
the kernel as to resend the skb to all the listening socket in
this case.
Signed-off-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the max packet size for some class (configured through tc) is
violated by the actual size of the packets of that class, then QFQ
would not schedule classes correctly, and the data structures
implementing the bucket lists may get corrupted. This problem occurs
with TSO/GSO even if the max packet size is set to the MTU, and is,
e.g., the cause of the failure reported in [1]. Two patches have been
proposed to solve this problem in [2], one of them is a preliminary
version of this patch.
This patch addresses the above issues by: 1) setting QFQ parameters to
proper values for supporting TSO/GSO (in particular, setting the
maximum possible packet size to 64KB), 2) automatically increasing the
max packet size for a class, lmax, when a packet with a larger size
than the current value of lmax arrives.
The drawback of the first point is that the maximum weight for a class
is now limited to 4096, which is equal to 1/16 of the maximum weight
sum.
Finally, this patch also forcibly caps the timestamps of a class if
they are too high to be stored in the bucket list. This capping, taken
from QFQ+ [3], handles the unfrequent case described in the comment to
the function slot_insert.
[1] http://marc.info/?l=linux-netdev&m=134968777902077&w=2
[2] http://marc.info/?l=linux-netdev&m=135096573507936&w=2
[3] http://marc.info/?l=linux-netdev&m=134902691421670&w=2
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Tested-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.
drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The MODULE_DEVICE_TABLE entry for dw_mci_exynos_match
was incorrectly copied from the platform back-end, which
causes this error when building the driver as a loadable
module:
drivers/mmc/host/dw_mmc-exynos.c: At top level:
drivers/mmc/host/dw_mmc-exynos.c:226:34: error: '__mod_of_device_table' aliased to undefined symbol 'dw_mci_pltfm_match'
This patch fixes the problem by just using the correct
string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Commit 473b095a72a9 ("mmc: sdhci: fix incorrect command used in tuning")
introduced a NULL dereference at resume-time if an SD 3.0 host controller
raises the SDHCI_NEEDS_TUNING flag while no card is inserted. Seen on an
OLPC XO-4 with sdhci-pxav3, but presumably affects other controllers too.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: stable <stable@vger.kernel.org> [3.3+]
|
|
There are two problems here:
The check for vmmc was printing an unnecessary pr_info() when
host->vmmc is NULL.
The intent of the check for vqmmc was to only remove UHS if we have a
regulator that doesn't support the required voltage, but since IS_ERR()
doesn't catch NULL, we were actually removing UHS modes if vqmmc isn't
present at all -- since it isn't present for most users, this breaks
UHS for them. This patch fixes that UHS regression in 3.7-rc1.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Bin Wang <binw@marvell.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
1. Never ever publish a device in the system before it has been setup
to a usable state.
2. Unregister the device _BEFORE_ taking away any resources it may be
using.
3. Don't check clks against NULL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
A recent commit "mmc: sh_mmcif: fix clock management" has introduced a
use after free bug in sh_mmcif.c: in sh_mmcif_remove() the call to
mmc_free_host() frees private driver data, therefore using it afterwards
is a bug. Revert that hunk.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: stable@vger.kernel.org [3.6]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The SDHCI standard defines a 256 byte register set but a device
that specifies a larger iomem region is not an error. Alter the
message condition accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The correct name for the driver is "mxc-mmc".
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
dev->platform_data is NULL in case of device tree boot,
instead use the saved version in struct omap_hsmmc_host.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
struct omap_hsmmc_host *host should not be accessed after mmc_free_host().
Reorder mmc_free_host() after iounmap(host->base).
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
800d78bfccb3d ("mmc: dw_mmc: add support for implementation specific
callbacks") -- merged in v3.7-rc1 -- introduced multiple NULL pointer
dereferences when the default dw_mci_pltfm_probe() is used, as it sets
host->drv_data to NULL, and that's only checked against NULL in 1 out of
the 7 cases where it is dereferenced.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
As mmc_start_host is getting called before enabling the dw_mmc controller
interrupt, there is a problem of missing the SDMMC_INT_CMD_DONE for the
very first command sent by the sdio_reset.
This problem occurs only when we disable MMC debugging i.e, MMC_DEBUG=n.
This patch enables the dw_mmc controller interrupt before mmc_start_host.
Signed-off-by: Yuvaraj CD <yuvaraj.cd@samsung.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
CMD23 causes lots of errors in kernel on some freescale SoCs
(P1020, P1021, P1022, P1024, P1025 and P4080) when MMC card used,
which is because these controllers does not support CMD23,
even on the SoCs which declares CMD23 is supported.
Therefore, we'll not use CMD23.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch removes the following warning.
drivers/mmc/host/dw_mmc.c:1976: warning: passing argument 1 of
'_dev_info' from incompatible pointer type
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Even though platform_get_irq returns error, 'host->irq'
always has an unsigned value. Less-than-zero comparison
of an unsigned value is never true. Type of 'unsigned int'
will be changed for 'int'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The RayDAT reports the sync status of its inputs in consecutive bit
positions, so all we do in hdspm_s1_sync_check is to iterate over idx:
status = hdspm_read(hdspm, HDSPM_RD_STATUS_1);
lock = (status & (0x1<<idx)) ? 1 : 0;
sync = (status & (0x100<<idx)) ? 1 : 0;
The index is given in kcontrol->private_value:
HDSPM_SYNC_CHECK("WC SyncCheck", 0),
HDSPM_SYNC_CHECK("AES SyncCheck", 1),
HDSPM_SYNC_CHECK("SPDIF SyncCheck", 2),
HDSPM_SYNC_CHECK("ADAT1 SyncCheck", 3),
HDSPM_SYNC_CHECK("ADAT2 SyncCheck", 4),
HDSPM_SYNC_CHECK("ADAT3 SyncCheck", 5),
HDSPM_SYNC_CHECK("ADAT4 SyncCheck", 6),
HDSPM_SYNC_CHECK("TCO SyncCheck", 7),
HDSPM_SYNC_CHECK("SYNC IN SyncCheck", 8),
The patch corrects the indicated sync flags by passing the proper index
value to hdspm_s1_sync_check().
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We end up with:
ERROR: "HYPERVISOR_event_channel_op" [drivers/xen/xen-gntdev.ko] undefined!
ERROR: "privcmd_call" [drivers/xen/xen-privcmd.ko] undefined!
ERROR: "HYPERVISOR_grant_table_op" [drivers/net/xen-netback/xen-netback.ko] undefined!
and this patch exports said function (which is implemented in hypercall.S).
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
As there is no need for it (the fallback code is for older
hypervisors and they only run under x86), and also b/c
we get:
drivers/xen/fallback.c: In function 'xen_event_channel_op_compat':
drivers/xen/fallback.c:10:19: error: storage size of 'op' isn't known
drivers/xen/fallback.c:15:2: error: implicit declaration of function '_hypercall1' [-Werror=implicit-function-declaration]
drivers/xen/fallback.c:15:19: error: expected expression before 'int'
drivers/xen/fallback.c:18:7: error: 'EVTCHNOP_close' undeclared (first use in this function)
drivers/xen/fallback.c:18:7: note: each undeclared identifier is reported only once for each function it appears in
.. and more
[v1: Moved the enablement to be covered by CONFIG_X86 per Ian's suggestion]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
exit_idle() should be called after irq_enter(), otherwise it throws:
[ INFO: suspicious RCU usage. ]
3.6.5 #1 Not tainted
-------------------------------
include/linux/rcupdate.h:725 rcu_read_lock() used illegally while idle!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 1
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: (rcu_read_lock){......}, at: [<ffffffff810e9fe0>] __atomic_notifier_call_chain+0x0/0x140
stack backtrace:
Pid: 0, comm: swapper/0 Not tainted 3.6.5 #1
Call Trace:
<IRQ> [<ffffffff811259a2>] lockdep_rcu_suspicious+0xe2/0x130
[<ffffffff810ea10c>] __atomic_notifier_call_chain+0x12c/0x140
[<ffffffff810e9fe0>] ? atomic_notifier_chain_unregister+0x90/0x90
[<ffffffff811216cd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff810ea136>] atomic_notifier_call_chain+0x16/0x20
[<ffffffff810777c3>] exit_idle+0x43/0x50
[<ffffffff81568865>] xen_evtchn_do_upcall+0x25/0x50
[<ffffffff81aa690e>] xen_do_hypervisor_callback+0x1e/0x30
<EOI> [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000
[<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000
[<ffffffff81061540>] ? xen_safe_halt+0x10/0x20
[<ffffffff81075cfa>] ? default_idle+0xba/0x570
[<ffffffff810778af>] ? cpu_idle+0xdf/0x140
[<ffffffff81a4d881>] ? rest_init+0x135/0x144
[<ffffffff81a4d74c>] ? csum_partial_copy_generic+0x16c/0x16c
[<ffffffff82520c45>] ? start_kernel+0x3db/0x3e8
[<ffffffff8252066a>] ? repair_env_string+0x5a/0x5a
[<ffffffff82520356>] ? x86_64_start_reservations+0x131/0x135
[<ffffffff82524aca>] ? xen_start_kernel+0x465/0x46
Git commit 98ad1cc14a5c4fd658f9d72c6ba5c86dfd3ce0d5
Author: Frederic Weisbecker <fweisbec@gmail.com>
Date: Fri Oct 7 18:22:09 2011 +0200
x86: Call idle notifier after irq_enter()
did this, but it missed the Xen code.
Signed-off-by: Mojiong Qiu <mjqiu@tencent.com>
Cc: stable@vger.kernel.org # from 3.3 and newer.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Makes it easier to troubleshoot in the field.
Acked-by: Ian Campbell <ian.campbell@citrix.com>
[v1: Use macro per Ian's suggestion]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Fix the return value of cs42l52_set_fmt() when clock inversion is
not allowed and also remove the useless variable ret.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
[We had been assigning to ret but then ignoring the value we assgined
-- broonie]
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The order shouldn't matter, but this seems to cause regressions for
certain specific cases. This should fix it for now. We probably
need to investigate a proper fix in the next development cycle.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Andy Furniss <andyqos@ukfsn.org>
|
|
To parse properly the subwoofer outputs on ASUS G75 laptop with VT1802
codec, correct the default configurations of speaker pins 0x24 and
0x33.
Reported-by: Massimo Del Fedele <max@veneto.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
VT1802 codec provides the invalid connection lists of NID 0x24 and
0x33 containing the routes to a non-exist widget 0x3e. This confuses
the auto-parser. Fix it up in the driver by overriding these
connections.
Reported-by: Massimo Del Fedele <max@veneto.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In via_auto_fill_adc_nids(), the parser tries to fill dac_nids[] at
the point of the current line-out (i). When no valid path is found
for this output, this results in dac = 0, thus it creates a hole in
dac_nids[]. This confuses is_empty_dac() and trims the detected DAC
in later reference.
This patch fixes the bug by appending DAC properly to dac_nids[] in
via_auto_fill_adc_nids().
Reported-by: Massimo Del Fedele <max@veneto.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In gfs2_trans_add_bh(), gfs2 was testing if a there was a bd attached to the
buffer without having the gfs2_log_lock held. It was then assuming it would
stay attached for the rest of the function. However, without either the log
lock being held of the buffer locked, __gfs2_ail_flush() could detach bd at any
time. This patch moves the locking before the test. If there isn't a bd
already attached, gfs2 can safely allocate one and attach it before locking.
There is no way that the newly allocated bd could be on the ail list,
and thus no way for __gfs2_ail_flush() to detach it.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
file_accessed() was being called by gfs2_mmap() with a shared glock. If it
needed to update the atime, it was crashing because it dirtied the inode in
gfs2_dirty_inode() without holding an exclusive lock. gfs2_dirty_inode()
checked if the caller was already holding a glock, but it didn't make sure that
the glock was in the exclusive state. Now, instead of calling file_accessed()
while holding the shared lock in gfs2_mmap(), file_accessed() is called after
grabbing and releasing the glock to update the inode. If file_accessed() needs
to update the atime, it will grab an exclusive lock in gfs2_dirty_inode().
gfs2_dirty_inode() now also checks to make sure that if the calling process has
already locked the glock, it has an exclusive lock.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Currently implementation in gfs2 uses FITRIM arguments as it were in
file system blocks units which is wrong. The FITRIM arguments
(fstrim_range.start, fstrim_range.len and fstrim_range.minlen) are
actually in bytes.
Moreover, check for start argument beyond the end of file system, len
argument being smaller than file system block and minlen argument being
bigger than biggest resource group were missing.
This commit converts the code to convert FITRIM argument to file system
blocks and also adds appropriate checks mentioned above.
All the problems were recognised by xfstests 251 and 260.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
When the fstrim_range argument is not provided by user in FITRIM ioctl
we should just return EFAULT and not promoting bad behaviour by filling
the structure in kernel. Let the user deal with it.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Cleans up two cases where variables were assigned values but then never
used again.
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Despite the return value from kmem_cache_zalloc() being checked, the
error wasn't being returned until after a possible null pointer
dereference. This patch returns the error immediately, allowing the
removal of the error variable.
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Check the return value of gfs2_rs_alloc(ip) and avoid a possible null
pointer dereference.
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Add missing index that may have led us to enabling
more crtcs than necessary.
May also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=56139
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some drivers (specifically vmwgfx) look at dev_mapping
in their open hook, so we have to set dev->dev_mapping
earlier in the process.
Reference:
http://lists.freedesktop.org/archives/dri-devel/2012-October/029420.html
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reported-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@vger.kernel.org
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If drm_setup (called at first open) fails, the whole
open call has failed, so we should not keep the
open_count incremented.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Cc: stable@vger.kernel.org
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bitmap_or uses the number of bits as its length parameter and
not the number of words necessary to store those bits.
This fixes a regression introduced by:
aa92b33 s390/cio: use generic bitmap functions
Reported-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The early mini sclp driver may be called in zArch mode either in
31 or 64 bit addressing mode.
If called in 31 bit addressing mode the new external interrupt psw
however would switch to 64 bit addressing mode. This would cause an
addressing exception within the interrupt handler, since the code
didn't expect the zArch/31 bit addressing mode combination.
Fix this by setting the new psw addressing mode bits so they fit
the current addressing mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
There's no need to keep __MAX_SUBCHANNEL and __MAX_SSID private to the
common I/O layer when __MAX_CSSID is usable by everybody.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
Takashi Iwai
Ian Coolidge
Vipul Pandya
Lee Jones
Seungwon Jeon
Eric Leblond
Paolo Valente
Thomas Abraham
Arnd Bergmann
Chris Ball
Kevin Liu
Russell King - ARM Linux
Guennadi Liakhovetski
Adrian Hunter
Fabio Estevam
Balaji T K
James Hogan
Yuvaraj CD
Jerry Huang
Adrian Knoth
Konrad Rzeszutek Wilk
Mojiong Qiu
Wei Yongjun
Charles Keepax
Alex Deucher
Benjamin Marzinski
Lukas Czerner
Andrew Price
Ilija Hadzic
David S. Miller
Sebastian Ott
Heiko Carstens
Cornelia Huck