| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Replace the calls to hda_dsp_set_power_state() with the
top-level SOF op snd_sof_set_power_state().
Along with this, modify the hda_dsp_resume() function to return
the value of snd_sof_set_power_state() directly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200228234225.6963-1-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set DONE bit after the FW_PURGE IPC is polled successfully, to clear the
interrupt and avoid the arrival of the confusing unexpected ipc.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Link: https://lore.kernel.org/r/20200228231850.9226-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support to configure the HDA controller with an external HDA
codec even if iDisp codec in i915 is not available.
This can happen for multiple reasons:
- internal graphics is disabled on the system
- i915 driver is not enabled in kernel or it fails to init
- i915 codec reports error in HDA codec probe
- HDA codec driver probe fails
Address all these scenarios, but keep using the existing topology.
In case failures occur, HDMI PCM nodes are created, but they will
report error if application tries to use them. No ALSA mixer controls
are created. If the external HDA codec init fails as well, SOF probe
will return error as before.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206085
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1163677
BugLink: https://github.com/thesofproject/linux/issues/1658
Link: https://lore.kernel.org/r/20200220171028.22023-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Declare extraction CPU DAI as well as sof_probe_compr_ops. FE DAIs can
link against these new CPU DAI to create new compress devices.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200218143924.10565-10-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add HDA handlers for soc_compr_ops and snd_compr_ops which cover probe
related operations. Implementation supports both connection purposes.
These merely define stream setups as core flow is covered by SOF
compress core.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200218143924.10565-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Hda stream is setup in similar fashion for compress as it is for pcm
operations. To reuse existing code in compress path, expose SDnFMT
helper routines.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200218143924.10565-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add all required types and methods to support each and every request
that driver could sent to firmware. Probe is one of SOF firmware
features which allows for data extraction and injection directly from
or to DMA stream.
Exposes eight IPCs:
- addition and removal of injection DMAs
- addition and removal of probe points
- info retrieval of injection DMAs and probe points
- probe initialization and cleanup
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200218143924.10565-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update stream irq handler definition to correctly set hdac_stream
current position when servicing stream interrupts for compress streams.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200218143924.10565-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
Trace DMA is disabled by default when the DSP is in D0I3.
Add a debug option to keep trace DMA enabled when the DSP
is in D0I3 during S0.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200129220726.31792-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch implements support for DSP D0i3 when the system
is in S0. The basic idea is to schedule a delayed work after
every successful IPC TX that checks if there are only
D0I3-compatible streams active and if so transition
the DSP to D0I3.
With the introduction of DSP D0I3 in S0, we need to
ensure that the DSP is in D0I0 before sending any new
IPCs. The exception for this would be the
compact IPCs that are used to set the DSP in
D0I3/D0I0 states.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200129220726.31792-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Amend the DSP state transition diagram in preparation
for introducing the feature to support opportunistic
DSP D0I3 state when the system is in S0.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200129220726.31792-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DSP device substates such as D0I0/D0I3
are platform-specific. Therefore, the d0_substate
field of struct snd_sof_dev is replaced
with the dsp_power_state field which represents the current
state of the DSP. This field holds both the device state
and the platform-specific substate values.
With the DSP device substates being platform-specific,
the DSP power state transitions need to be performed in
the platform-specific suspend/resume ops as well.
In order to achieve this, the ops signature has to be
modified to pass the target device state as an
argument. The target substate will be determined by
the platform-specific ops before performing the transition.
For example, in the case of the system suspending to S0IX,
the top-level SOF device suspend callback needs to
only determine if the DSP will be entering
D3 or remain in D0. The target substate in case the device
needs to remain in D0 (D0I0 or D0I3) will be determined
by the platform-specific suspend op.
With the addition of the extended set of power states for the DSP,
the set_power_state op for HDA platforms has to be extended
to handle only the appropriate state transitions. So, the
implementation for the Intel HDA platforms is also modified.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200129220726.31792-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the system_suspend_target field to struct snd_sof_dev
to track the intended system suspend power target. This will
be used as one of the criteria for determining the
final DSP power state.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200129220726.31792-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To be compliant with i915 display driver requirements, i915 power-up
must be done before any HDA communication takes place, including
parsing the bus capabilities. Otherwise the initial codec probe
may fail.
Move i915 initialization earlier in the SOF HDA sequence. This
sequence is now aligned with the snd-hda-intel driver where the
display_power() call is before snd_hdac_bus_parse_capabilities()
and rest of the capability parsing.
Also remove unnecessary ifdef around hda_codec_i915_init(). There's
a dummy implementation provided if CONFIG_SND_SOC_SOF_HDA is not
enabled.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200206200223.7715-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When HDA controller is resumed from suspend, i915 HDMI/DP
codec requires that following order of actions is kept:
- i915 display power up and configuration of link params
- hda link reset and setup
Current SOF HDA code delegates display codec power control
to the codec driver. This works most of the time, but in
runtime PM sequences, the above constraint may be violated.
On platforms where BIOS values for HDA link parameters do
not match hardware reset defaults, this may lead to errors
in HDA verb transactions after resume.
Fix the issue by explicitly powering the display codec
in the HDA controller resume/suspend calls, thus ensuring
correct ordering. Special handling is needed for the D0i3
flow, where display power must be turned off even though
DSP is left powered.
Now that we have more invocations of the display power helper
functions, the conditional checks surrounding each call have
been moved inside hda_codec_i915_display_power(). The two
special cases of display powering at initial probe are handled
separately. The intent is to avoid powering the display whenever
no display codecs are used.
Note that early powering of display was removed in
commit 687ae9e287b3 ("ASoC: intel: skl: Fix display power regression").
This change was also copied to the SOF driver. No failures
have resulted as hardware default values for link parameters
have worked out of the box. However with recent i915 driver
changes like done in commit 87c1694533c9 ("drm/i915: save
AUD_FREQ_CNTRL state at audio domain suspend"), this does not
hold anymore and errors are hit.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200206200223.7715-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC: Fixes for v5.6
A collection of updates for bugs fixed since the initial pull
request, the most important one being the addition of COMMON_CLK
for wcd934x which is needed for MFD to be merged.
|
|
Change HDA probe behaviour slightly so that i915 power is not
turned off if i915 audio codecs are found in the initial probe done
by SOF Intel driver, and power is kept on until HDA codec driver
probe runs.
This will reduce number of mode sets on platforms with low
minimum CDCLK (like GLK) and brings the SOF probe sequence closer
to legacy HDA driver in terms of i915 audio codec power management.
BugLink: https://github.com/thesofproject/linux/issues/1642
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200120160117.29130-3-kai.vehmanen@linux.intel.com
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current interface to control i915 display power is misleading.
The hda_codec_i915_get() and hda_codec_i915_put() names suggest
a refcounting based interface. This is confusing as no refcounting
is done and the underlying HDAC library interface does not support
refcounts eithers.
Clarify the code by replacing the functions with a single
hda_codec_i915_display_power() that is aligned with
snd_hdac_display_power().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200120160117.29130-2-kai.vehmanen@linux.intel.com
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
ASoC: Fixes for v5.5
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
|
|
With fourth pin added for iDisp for skl_dai, update SOF_SKL_DAI_NUM to
account for the change. Without this, dais from the bottom of the list
are skipped. In current state that's the case for 'Alt Analog CPU DAI'.
Fixes: ac42b142cd76 ("ASoC: SOF: Intel: hda: Add iDisp4 DAI")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113114054.9716-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC: Fixes for v5.5
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
|
|
Fix GCC warning with W=1, previous cleanup did not remove unnecessary
variable.
sound/soc/sof/intel/hda-dai.c: In function ‘hda_link_pcm_prepare’:
sound/soc/sof/intel/hda-dai.c:265:31: warning: variable ‘hda_stream’
set but not used [-Wunused-but-set-variable]
265 | struct sof_intel_hda_stream *hda_stream;
| ^~~~~~~~~~
Fixes: a3ebccb52efdf ("ASoC: SOF: Intel: hda: reset link DMA state in prepare")
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113205620.27285-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.
SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.
Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().
Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We will reinit DSP in a loop when it fails to initialize the first
time, as recommended. So, it is not an error before we finally give
up. And reorder the trace to make it more readable.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC: Fixes for v5.5
More fixes that have been collected, nothing super remarkable here - the
few core fixes are mainly error handling related as are many of the
driver fixes.
|
|
|
|
TGL supports more than three iDisp DAI's.
Add support for iDisp4 CPU DAI.
Without this patch, we saw the below error on our TGL DUT:
sof_rt5682 tgl_max98357a_rt5682: ASoC: CPU DAI iDisp4 Pin not registered
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191220171037.10689-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that Xtensa stuff is only referenced in Intel stuff, define
namespace and import it in Intel BYT/BDW/HDaudio modules
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current structures are not well designed. We include Xtensa
information from the ACPI and PCI levels, but at the Kconfig/module
level everything Xtensa related is included at the sof/intel level.
Move the arch_ops under ops so that Xtensa is hidden in the DSP ops,
with a structure that follows the Kconfig/module partition.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Define namespaces (one generic and one dedicated for i915) and include
them in HDaudio top-level module.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case a HDA codec probe fails, do not raise error immediately,
but instead remove the codec from bus->codec_mask and continue
probe for other codecs.
This allows for more robust behaviour in cases where one codec
in the system is faulty. SOF driver load can still proceed with
the codecs that can be probed successfully. Probe may still
fail if suitable machine driver is not found, but in many
cases the generic HDA machine driver can operate with a subset
of codecs.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218002616.7652-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a state machine for FW boot to track the
different stages of FW boot and replace the boot_complete
field with fw_state field in struct snd_sof_dev.
This will be used to determine the actions to be performed
during system suspend.
One of the main motivations for adding this change is the
fact that errors during the top-level SOF device probe cannot
be propagated and therefore suspending the SOF device normally
during system suspend could potentially run into errors.
For example, with the current flow, if the FW boot failed
for some reason and the system suspends, the SOF device
suspend could fail because the CTX_SAVE IPC would be attempted
even though the FW never really booted successfully causing it
to time out. Another scenario that the state machine fixes
is when the runtime suspend for the SOF device fails and
the DSP is powered down nevertheless, the CTX_SAVE IPC during
system suspend would timeout because the DSP is already
powered down.
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218002616.7652-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Define namespace and include it in PCI top-level module.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are no known commercial devices using Haswell, and there is no
support for Haswell in SOF so remove remaining definitions and
structures.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Define namespace and include it in ACPI top-level module.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Define separate namespaces and include them in ACPI and PCI top-level
modules.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The legacy IPC routines are only used by broadwell and baytrail
modules, import them as needed and make sure other modules cannot load
them.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the PCM_PARAM IPC fails while configuring the FE, the kernel
oopses in the HDaudio link DMA .hw_free operation. The root cause is a
NULL dma_data since the BE .hw_params was never called by the SOC
core.
This error can also happen if the HDaudio link DMA configuration IPC
fails in the BE .hw_params.
This patches makes sure the dma_data is properly saved in .hw_params,
and tested before being use in hw_free.
GitHub issue: https://github.com/thesofproject/linux/issues/1417
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218000518.5830-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC: Fixes for v5.5
A collection of fixes since the merge window, mostly driver specific but
there's a few in the core that clean up fallout from the refactorings
done in the last cycle.
|
|
|
|
On Baytrail-CR, SSP0 needs to be used instead of SSP2. The
substitution is assumed to be done in the topology file.
When Baytrail-CR is detected, add -ssp0 suffix to the topology file
name so that the topology code picks up the correct file.
Tested on Asus T100TAF
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a module parameter 'codec_mask' to filter out unwanted
HDA codecs from driver probe. E.g. on most systems,
codec_mask=4 will limit to HDMI audio and exclude any
external HDA codecs.
Similar to 'probe_mask' module parameter of snd-hda-intel.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Turns out SSP 3-5 are only available on cht, to avoid dumping on
undefined registers let's split the definition.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, SOF probes machine drivers by creating a platform device
and passing the machine description as private data.
This is driven by the ACPI restrictions. Ideally, ACPI tables
should contain the description for the machine driver. This is
not possible because ACPI tables are frozen and used on multiple
OS-es (e.g Windows).
In the case of Device Tree we don't have this restriction, so we
choose to probe the machine drivers by creating a DT node as is
the standard ALSA way.
This patch makes the probing of machine drivers from SOF
core optional allowing for Device Tree platforms to decouple
the SOF core from machine driver probing.
Along with this, it also consolidates the machine driver selection
for Intel platforms by defining optional ops for selecting the machine
driver based on the ACPI match for HDA and non-HDA platforms and
setting the mach params.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204211556.12671-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The machine driver selection for HDA platforms will be
consolidated and moved out of the SOF DSP
probe callback. In preparation for that, modify the
signature for hda_codec_probe_bus() to pass the
hda_codec_use_common_hdmi as a variable while probing the
HDA codecs.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204211556.12671-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move all the audio-specific code in the core,
audio-specific logic in the top-level PM callbacks
and the core header files into a separate file
(sof-audio.*) in preparation for adding an
audio client device.
In the process of moving all structure definitions
for widget, routes, pcm's etc, the snd_sof_dev
member in all these structs is replaced with
the snd_soc_component member. Also, use the component
device instead of the snd_sof_dev device wherever
possible in the PCM component driver,
control IO functions and the topology parser as the
component device will be moved over to the client
device later on.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204211556.12671-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is required for the auto-detection in the user space (for UCM).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191204211556.12671-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
Ranjani Sridharan
Keyon Jie
Kai Vehmanen
Cezary Rojewski
Mark Brown
Takashi Iwai
Pierre-Louis Bossart
Bard liao
Sathyanarayana Nujella
Curtis Malainey
Daniel Baluta
Jaroslav Kysela