| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The sun8i-h3 introduces a lot of changes to the i2s block such
as different register locations, extended clock division and
more operational modes. As we have to consider the earlier
implementation then these changes need to be isolated.
None of the new functionality has been implemented yet, the
driver has just been expanded to allow it work on the H3 SoC.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The default value of the config register is different on newer
SoCs and therefore enabling/disabling with a register write
will clear bits used to set the direction of the clock and frame
pins.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The newer SoCs do not have this setting. Instead they set the pin
direction. Add a check to see if the bit is valid and if so set
it accordingly.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On the newer SoCs the bits to configure the operational mode are
located in a different register. Add a regmap field so that this
location can be configured.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The location of the mclk output enable bit is different on newer
SoCs. Use a regmap field to enable it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On newer SoCs the bit fields for the blck and lrclk polarity are in
a different locations. Use regmap fields to set the polarity bits
as intended.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On newer SoCs the location of the slot width select and sample
resolution are different and also there is a bigger range of
support.
For the current supported rates then an offset is required.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On the original i2s block the channel mapping and selection were
configured for stereo audio by default: This is not the case with
the newer SoCs and they are also located at different offsets.
To support the newer SoC then regmap fields have been added to the
quirks and these are initialised to their correct settings during
probing.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
First of all,the address of pdev->dev is assigned to card->dev in
create_card,then the function platform_set_drvdata copies the value
the variable card to pdev->dev.driver_data, but when calling
snd_soc_register_card,the function dev_set_drvdata(card->dev, card)
will also do the same copy operation,so i think that the former copy
operation can be removed.
Signed-off-by: Peng Donglin <dolinux.peng@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It has been seen that the newer SoCs have a different TX FIFO
address. Add this to the quirks structure.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The newer SoCs have a larger range than the original SoC that this
driver was developed for. By adding the regmap config to the quirks
then the driver can initialise the managed register map correctly.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCLKDIV and MCLKDIV found on newer SoCs start from an offset of 1.
Add the functionality to adjust the division values according to the
needs to the device being used.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Declare snd_soc_codec_driver structures as const as they are either
passed as an argument to the function snd_soc_register_codec or stored as
reference in field codec of type sun4i_codec_quirks. Both the fucntion
argument and the codec field are of type const, so declare the
structures with this property as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for the changes required to support newer SoCs then
quirks has been moved and also added to the device structure.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec in the V3s is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the V3s does not have LINEIN, LINEOUT, MBIAS and MIC2,
MIC3, and the FIFO related registers are like H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The V3s SoC features an analog codec with headphone support but without
mic2 and linein.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Allwinner V3s has an analog codec without MIC2 and Line In, which will
need a special set of mixer controls/widgets/routes, otherwise meaningless
controls will be exported to userspace and confuse the user.
Add the special set, and use it when the SoC has no MIC2 and Line In.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Allwinner V3s features an analog codec without MBIAS pin.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the driver to use SND_SOC_DAPM_AIF_IN instead of
SND_SOC_DAPM_DAC.
Rename the interface's widgets to be more precise on which slot
the interface is connected.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
An unwanted space is present in an audio widget's name on the dapm
routing. It causes an error on the recognition of this widget (error:
("no dapm match for AIF1 Slot 0 Right").
Remove the space fixes it.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Allwinner V3s features an analog codec without LINEIN.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Allwinner V3s features an analog codec without MIC2.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SOC_MIXER_ARRAY is a simplified function of SND_SOC_DAPM_MIXER
which handles automatically the ARRAY_SIZE of controls.
Update the driver to use SOC_MIXER_ARRAY.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the driver to use the new SOC_DAPM_DOUBLE definition
on the digital DAC mixer.
Update the names accordingly as, when they are shared, the
controls are not prefixed with the widget's name anymore.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "HP" widget is already present and take part to
the analog part (sun8i-codec-analog).
Remove it from the digital part as it is unnecessary.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
It's not necessary to unregister a component registered
with devm_snd_soc_register_component(). Also removed
pointness clk_disable_unprepare() from error path and
snd_soc_unregister_platform() from the remove.
Fixes: f8260afa444b ("ASoC: sunxi: Add support for the SPDIF block")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some SoCs have a reset line that must be asserted/deasserted.
This patch adds a quirk to handle the new compatible
"allwinner,sun6i-a31-i2s" which will deassert the reset
line on probe function and assert it on remove's one.
This new compatible is useful in case of A33 codec driver, for example.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the sun8i audio codec which handles the digital register of
A33 codec.
The driver handles only the basic playback from the DAC to headphones.
All other features (microphone, capture, etc) will be added later.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When playing a sound for the first time, a short delay, where the audio
file is not played, can be noticed.
On a second play (right after), the sound is played correctly.
If we wait a short time (~5 sec which corresponds to the aplay
timeout), the delay is back.
This patch fixes it by using an event on headphone amplifier.
It allows to keep the amplifier enable while playing a sound.
A delay of 700ms allows to wait that the amplifier is powered-up
before playing the sound.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The H3 SoC uses the same SPDIF block as found in earlier SoCs, but its
TXFIFO is mapped to another address.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As done previously for sun4i-codec, the DMA maxburst of 4
is not supported by every SoCs so the DMA controller engine
returns "unsupported value".
As a maxburst of 8 is supported by all variants, this patch
increases it to 8.
For more details, see commit from Chen-Yu Tsai:
commit 730e2dd0cbc7 ("ASoC: sun4i-codec: Increase DMA max burst to 8")
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mono differential output for "Line Out" downmixes the stereo audio
from the mixer, instead of just taking the left channel.
Add a route from the "Right Mixer" to "Line Out Source Playback Route"
through the "Mono Differential" path, so DAPM doesn't shut down
everything if the left channel is muted.
Fixes: 0f909f98d7cb ("ASoC: sun4i-codec: Add support for A31 Line Out
playback")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It has been seen that some newer SoCs have a different TX FIFO
address and we already have the difference with the A31 requiring
a reset. Add a quirks structure so that these can be managed
easily.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dapm components are now handled by the ALSA SoC SPDIF DIT driver
so can be removed.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Oddly enough, my version of GCC misses this uninitialized variable.
Fixes: ba2ff3027b5a ("ASoC: sunxi: Add support for A23/A33/H3 codec's analog path controls")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The internal codec on A23/A33/H3 is split into 2 parts. The
analog path controls are routed through an embedded custom register
bus accessed through the PRCM block.
The SoCs share a common set of inputs, outputs, and audio paths.
The following table lists the differences.
----------------------------------------
| Feature \ SoC | A23 | A33 | H3 |
----------------------------------------
| Headphone | v | v | |
----------------------------------------
| Line Out | | | v |
----------------------------------------
| Phone In/Out | v | v | |
----------------------------------------
Add an ASoC component driver for it. This should be tied to the codec
audio card as an auxiliary device. This patch adds the commont paths
and controls, and variant specific headphone out and line out.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sound/soc/sunxi/sun4i-codec.c:1339:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The later Allwinner SoCs have a dedicated reset controller, and
peripherals have dedicated reset controls which need to be deasserted
before the associated peripheral can be used.
Add support for this to the quirks structure and probe/remove functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31's internal codec capture path has a mixer in front of the ADC
for each channel, capable of selecting various inputs, including
microphones, line in, phone in, and the main output mixer.
This patch adds the various controls, widgets and routes needed for
audio capture from the already supported inputs on the A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In our i2s driver, we were previously trying to guess which oversample the
user wanted to use by looking at the rate and trying to max it.
However, the cards, and especially simple-card with its mclk-fs property
will already provide the expected oversample ratio by using the set_sysclk
callback.
We can thus implement it and remove the logic to deal with the runtime
guess.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 SoC's codec has various inputs, outputs and microphone bias
supplies. These can be routed on the board in different ways, such as:
- HPCOM may be connected to have the headphone DC coupled.
- Microphones all use the MBIAS main microphone supply or one mic may
use the HBIAS supply, which supports headset detection and buttons.
- Line Out may be routed to an audio jack, or an onboard speaker amp
with power controls.
Add support for specifying the audio routes in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 internal codec has 3 microphone outputs, of which MIC2 and MIC3
are muxed internally. The resulting two microphone inputs have separate
gain controls and mixer inputs.
The codec also has 2 microphone bias pins. HBIAS is specifically for the
headphone jack, which also supports headphone detection and control
buttons. These extra functions are not supported yet. The other, MBIAS,
is for all other analog microphones.
There is also mention of digital microphone support, but documentation
is scarce, and no hardware with it is available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
Marcus Cooper
Donglin Peng
Bhumika Goyal
Arvind Yadav
Philipp Zabel
Gustavo A. R. Silva
Fabio Estevam
Icenowy Zheng
Icenowy Zheng
Mylène Josserand
Mark Brown
Wei Yongjun
Chen-Yu Tsai
Dan Carpenter
kbuild test robot
Maxime Ripard