| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Commit 754fe4a92c07 ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
IS_ERR_VALUE macro should be used only with unsigned long type.
Otherwise it can work incorrectly.
The patch follows conclusion from discussion on LKML [1][2].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
If NO_DMA=y:
ERROR: "usb_gadget_map_request" [drivers/usb/dwc2/dwc2.ko] undefined!
ERROR: "usb_gadget_unmap_request" [drivers/usb/dwc2/dwc2.ko] undefined!
ERROR: "bad_dma_ops" [drivers/usb/dwc2/dwc2.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to check the qtd for that case.
Also fix one static analysis tool issue after fix the data toggle error.
John Youn:
* Added WARN() to warn on improper usage of the
dwc2_hcd_save_data_toggle() function.
Signed-off-by: Dyson Lee <dyson.lee@intel.com>
Signed-off-by: Tang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.
dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.
Commit 26a19ea699060fde ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.
Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.
Fixes: 26a19ea699060fde ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda6187181 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda6187181 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.
This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.
Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.
Fixes: 09c96980dc72 ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: Caesar Wang <caesar.upstream@gmail.com>
Reported-by: Michael Niewoehner <linux@mniewoehner.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Caesar Wang <caesar.upstream@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
|
|
The 'umidi' object will be free'd on the error path by snd_usbmidi_free()
when tearing down the rawmidi interface. So we shouldn't try to free it
in snd_usbmidi_create() after having registered the rawmidi interface.
Found by KASAN.
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the RC QPs send queue overhead computation to take into account
two additional segments in the WQE which are needed for registration
operations.
The ATOMIC and UMR segments can't coexist together, so chose maximum out
of them.
The commit 9e65dc371b5c ("IB/mlx5: Fix RC transport send queue overhead
computation") was intended to update RC transport as commit messages
states, but added the code to UC transport.
Fixes: 9e65dc371b5c ("IB/mlx5: Fix RC transport send queue overhead computation")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
A narrow window for race condition still exist between
multicast join thread and *dev_flush workers.
A kernel crash caused by prolong erratic link state changes
was observed (most likely a faulty cabling):
[167275.656270] BUG: unable to handle kernel NULL pointer dereference at
0000000000000020
[167275.665973] IP: [<ffffffffa05f8f2e>] ipoib_mcast_join+0xae/0x1d0 [ib_ipoib]
[167275.674443] PGD 0
[167275.677373] Oops: 0000 [#1] SMP
...
[167275.977530] Call Trace:
[167275.982225] [<ffffffffa05f92f0>] ? ipoib_mcast_free+0x200/0x200 [ib_ipoib]
[167275.992024] [<ffffffffa05fa1b7>] ipoib_mcast_join_task+0x2a7/0x490
[ib_ipoib]
[167276.002149] [<ffffffff8109d5fb>] process_one_work+0x17b/0x470
[167276.010754] [<ffffffff8109e3cb>] worker_thread+0x11b/0x400
[167276.019088] [<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400
[167276.027737] [<ffffffff810a5aef>] kthread+0xcf/0xe0
Here was a hit spot:
ipoib_mcast_join() {
..............
rec.qkey = priv->broadcast->mcmember.qkey;
^^^^^^^
.....
}
Proposed patch should prevent multicast join task to continue
if link state change is detected.
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Changes from v4:
- as suggested by Doug Ledford, optimized spinlock usage,
i.e. ipoib_mcast_join() is called with lock held.
Changes from v3:
- sync with priv->lock before flag check.
Chages from v2:
- Move check for OPER_UP flag state to mcast_join() to
ensure no event worker is in progress.
- minor style fixes.
Changes from v1:
- No need to lock again if error detected.
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch fixes vulnerability CVE-2016-2085. The problem exists
because the vm_verify_hmac() function includes a use of memcmp().
Unfortunately, this allows timing side channel attacks; specifically
a MAC forgery complexity drop from 2^128 to 2^12. This patch changes
the memcmp() to the cryptographically safe crypto_memneq().
Reported-by: Xiaofei Rex Guo <xiaofei.rex.guo@intel.com>
Signed-off-by: Ryan Ware <ware@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
MMUv4 supports 2 concurrent page sizes: Normal and Super [4K to 16M]
So far Linux supported a single super page size for a given Normal page,
depending on the software page walking address split.
e.g. we had 11:8:13 address split for 8K page, which meant super page
was 2 ^(8+13) = 2M (given that THP size has to be PMD_SHIFT)
Now we turn this around, by allowing multiple Super Pages in Kconfig
(currently 2M and 16M only) and forcing page walker address split to
PGDIR_SHIFT and PAGE_SHIFT
For configs without Super page, things are same as before and
PGDIR_SHIFT can be hacked to get non default address split
The motivation for this change is a customer who needs 16M super page
and a 8K Normal page combo.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
arch/x86/built-in.o: In function `uv_bios_call':
(.text+0xeba00): undefined reference to `efi_call'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The pfn_t type uses an unsigned long to store a pfn + flags value. On a
64-bit platform the upper 12 bits of an unsigned long are never used for
storing the value of a pfn. However, this is not true on highmem
platforms, all 32-bits of a pfn value are used to address a 44-bit
physical address space. A pfn_t needs to store a 64-bit value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=112211
Fixes: 01c8f1c44b83 ("mm, dax, gpu: convert vm_insert_mixed to pfn_t")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Stuart Foster <smf.linux@ntlworld.com>
Reported-by: Julian Margetson <runaway@candw.ms>
Tested-by: Julian Margetson <runaway@candw.ms>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Mike said:
: CONFIG_UBSAN_ALIGNMENT breaks x86-64 kernel with lockdep enabled, i. e
: kernel with CONFIG_UBSAN_ALIGNMENT fails to load without even any error
: message.
:
: The problem is that ubsan callbacks use spinlocks and might be called
: before lockdep is initialized. Particularly this line in the
: reserve_ebda_region function causes problem:
:
: lowmem = *(unsigned short *)__va(BIOS_LOWMEM_KILOBYTES);
:
: If i put lockdep_init() before reserve_ebda_region call in
: x86_64_start_reservations kernel loads well.
Fix this ordering issue permanently: change lockdep so that it uses
hlists for the hash tables. Unlike a list_head, an hlist_head is in its
initialized state when it is all-zeroes, so lockdep is ready for
operation immediately upon boot - lockdep_init() need not have run.
The patch will also save some memory.
lockdep_init() and lockdep_initialized can be done away with now - a 4.6
patch has been prepared to do this.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Suggested-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[akpm@linux-foundation.org: s/threshhold/threshold/]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This showed up on ARC when running LMBench bw_mem tests as Overlapping
TLB Machine Check Exception triggered due to STLB entry (2M pages)
overlapping some NTLB entry (regular 8K page).
bw_mem 2m touches a large chunk of vaddr creating NTLB entries. In the
interim khugepaged kicks in, collapsing the contiguous ptes into a
single pmd. pmdp_collapse_flush()->flush_pmd_tlb_range() is called to
flush out NTLB entries for the ptes. This for ARC (by design) can only
shootdown STLB entries (for pmd). The stray NTLB entries cause the
overlap with the subsequent STLB entry for collapsed page. So make
pmdp_collapse_flush() call pte flush interface not pmd flush.
Note that originally all thp flush call sites in generic code called
flush_tlb_range() leaving it to architecture to implement the flush for
pte and/or pmd. Commit 12ebc1581ad11454 changed this by calling a new
opt-in API flush_pmd_tlb_range() which made the semantics more explicit
but failed to distinguish the pte vs pmd flush in generic code, which is
what this patch fixes.
Note that ARC can fixed w/o touching the generic pmdp_collapse_flush()
by defining a ARC version, but that defeats the purpose of generic
version, plus sementically this is the right thing to do.
Fixes STAR 9000961194: LMBench on AXS103 triggering duplicate TLB
exceptions with super pages
Fixes: 12ebc1581ad11454 ("mm,thp: introduce flush_pmd_tlb_range")
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [4.4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to use post-decrement to get percpu_counter_destroy() called on
&wb->stat[0]. Moreover, the pre-decremebt would cause infinite
out-of-bounds accesses if the setup code failed at i==0.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
DAX implements split_huge_pmd() by clearing pmd. This simple approach
reduces memory overhead, as we don't need to deposit page table on huge
page mapping to make split_huge_pmd() never-fail. PTE table can be
allocated and populated later on page fault from backing store.
But one side effect is that have to check if pmd is pmd_none() after
split_huge_pmd(). In most places we do this already to deal with
parallel MADV_DONTNEED.
But I found two call sites which is not affected by MADV_DONTNEED (due
down_write(mmap_sem)), but need to have the check to work with DAX
properly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The kptr_restrict flag, when set to 1, only prints the kernel address
when the user has CAP_SYSLOG. When it is set to 2, the kernel address
is always printed as zero. When set to 1, this needs to check whether
or not we're in IRQ.
However, when set to 2, this check is unneccessary, and produces
confusing results in dmesg. Thus, only make sure we're not in IRQ when
mode 1 is used, but not mode 2.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add missing kernel-doc notation for function parameter 'gfp_mask' to fix
kernel-doc warning.
mm/filemap.c:1898: warning: No description found for parameter 'gfp_mask'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When enabling UBSAN_SANITIZE_ALL, the kernel image size gets increased
significantly (~3x). So, it sounds better to have some note in Kconfig.
And, fixed a typo.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When checking specific attribute from a bit mask, need to use bitwise
AND and not logical AND, fixed that.
Fixes: 145d9c541032 ('IB/core: Display extended counter set if
available')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The while loop after err_slaves should use post-decrement; otherwise
we'll fail to do the kfrees for i==0, and will run into out-of-bounds
accesses if the setup above failed already at i==0.
[I'm not sure why one even bothers populating the ->vlan_filter array:
mlx4.h isn't #included by anything outside
drivers/net/ethernet/mellanox/mlx4/, and "git grep -C2 -w vlan_filter
drivers/net/ethernet/mellanox/mlx4/" seems to suggest that the
vlan_filter elements aren't used at all.]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This reverts commit 829b6962f7e3cfc06f7c5c26269fd47ad48cf503.
Revert this change as it causes a sysfs path to change and therefore
introduces and ABI regression. More precisely Android's vold is not being
able to access /sys/module/mmcblk/parameters/perdev_minors any more, since
the path becomes changed to: "/sys/module/mmc_block/..."
Fixes: 829b6962f7e3 ("mmc: block: don't use parameter prefix if built as
module")
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In __cpufreq_cooling_register() we allocate the arrays for time_in_idle
and time_in_idle_timestamp to be as big as the number of cpus in this
cpufreq device. However, in get_load() we access this array using the
cpu number as index, which can result in an out of bound access.
Index time_in_idle{,_timestamp} using the index in the cpufreq_device's
allowed_cpus mask, as we do for the load_cpu array in
cpufreq_get_requested_power()
Reported-by: Nicolas Boichat <drinkcat@chromium.org>
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The value of ctx->pos in the last readdir call is supposed to be set to
INT_MAX due to 32bit compatibility, unless 'pos' is intentially set to a
larger value, then it's LLONG_MAX.
There's a report from PaX SIZE_OVERFLOW plugin that "ctx->pos++"
overflows (https://forums.grsecurity.net/viewtopic.php?f=1&t=4284), on a
64bit arch, where the value is 0x7fffffffffffffff ie. LLONG_MAX before
the increment.
We can get to that situation like that:
* emit all regular readdir entries
* still in the same call to readdir, bump the last pos to INT_MAX
* next call to readdir will not emit any entries, but will reach the
bump code again, finds pos to be INT_MAX and sets it to LLONG_MAX
Normally this is not a problem, but if we call readdir again, we'll find
'pos' set to LLONG_MAX and the unconditional increment will overflow.
The report from Victor at
(http://thread.gmane.org/gmane.comp.file-systems.btrfs/49500) with debugging
print shows that pattern:
Overflow: e
Overflow: 7fffffff
Overflow: 7fffffffffffffff
PAX: size overflow detected in function btrfs_real_readdir
fs/btrfs/inode.c:5760 cicus.935_282 max, count: 9, decl: pos; num: 0;
context: dir_context;
CPU: 0 PID: 2630 Comm: polkitd Not tainted 4.2.3-grsec #1
Hardware name: Gigabyte Technology Co., Ltd. H81ND2H/H81ND2H, BIOS F3 08/11/2015
ffffffff81901608 0000000000000000 ffffffff819015e6 ffffc90004973d48
ffffffff81742f0f 0000000000000007 ffffffff81901608 ffffc90004973d78
ffffffff811cb706 0000000000000000 ffff8800d47359e0 ffffc90004973ed8
Call Trace:
[<ffffffff81742f0f>] dump_stack+0x4c/0x7f
[<ffffffff811cb706>] report_size_overflow+0x36/0x40
[<ffffffff812ef0bc>] btrfs_real_readdir+0x69c/0x6d0
[<ffffffff811dafc8>] iterate_dir+0xa8/0x150
[<ffffffff811e6d8d>] ? __fget_light+0x2d/0x70
[<ffffffff811dba3a>] SyS_getdents+0xba/0x1c0
Overflow: 1a
[<ffffffff811db070>] ? iterate_dir+0x150/0x150
[<ffffffff81749b69>] entry_SYSCALL_64_fastpath+0x12/0x83
The jump from 7fffffff to 7fffffffffffffff happens when new dir entries
are not yet synced and are processed from the delayed list. Then the code
could go to the bump section again even though it might not emit any new
dir entries from the delayed list.
The fix avoids entering the "bump" section again once we've finished
emitting the entries, both for synced and delayed entries.
References: https://forums.grsecurity.net/viewtopic.php?f=1&t=4284
Reported-by: Victor <services@swwu.com>
CC: stable@vger.kernel.org
Signed-off-by: David Sterba <dsterba@suse.com>
Tested-by: Holger Hoffstätte <holger.hoffstaette@googlemail.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Since the dawn of time the ICST code has only supported divide
by one or hang in an eternal loop. Luckily we were always dividing
by one because the reference frequency for the systems using
the ICSTs is 24MHz and the [min,max] values for the PLL input
if [10,320] MHz for ICST307 and [6,200] for ICST525, so the loop
will always terminate immediately without assigning any divisor
for the reference frequency.
But for the code to make sense, let's insert the missing i++
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Drivers may need to provide their own get_cd() mmc host op, but
currently the internals of the current op (sdhci_get_cd()) are
provided by sdhci_do_get_cd() which is also called from
sdhci_request().
To allow override of the get_cd functionality, change sdhci_request()
to call ->get_cd() instead of sdhci_do_get_cd().
Note, in the future the call to ->get_cd() will likely be removed
from sdhci_request() since most drivers don't need actually it.
However this change is being done now to facilitate a subsequent
bug fix.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the past, fixes for specific hardware devices were implemented
in sdhci using quirks. That approach is no longer accepted because
the growing number of quirks was starting to make the code difficult
to understand and maintain.
One alternative to quirks, is to allow drivers to override the default
mmc host operations. This patch makes it easy to do that, and it is
needed for a subsequent bug fix, for which separate patches are
provided.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Depending on the configuration either the 32 or 64 bit version of
elf_check_arch() is defined. parse_crash_elf{32|64}_headers() does
some basic verification of the ELF header via
vmcore_elf{32|64}_check_arch() which happen to map to elf_check_arch().
Since the implementation 32 and 64 bit version of elf_check_arch()
differ, we use the wrong type:
In file included from include/linux/elf.h:4:0,
from fs/proc/vmcore.c:13:
fs/proc/vmcore.c: In function 'parse_crash_elf64_headers':
>> arch/mips/include/asm/elf.h:228:23: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
struct elfhdr *__h = (hdr); \
^
include/linux/crash_dump.h:41:37: note: in expansion of macro 'elf_check_arch'
#define vmcore_elf64_check_arch(x) (elf_check_arch(x) || vmcore_elf_check_arch_cross(x))
^
fs/proc/vmcore.c:1015:4: note: in expansion of macro 'vmcore_elf64_check_arch'
!vmcore_elf64_check_arch(&ehdr) ||
^
Therefore, we rather define vmcore_elf{32|64}_check_arch() as a
basic machine check and use it also in binfm_elf?32.c as well.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Suggested-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12529/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The ARM GICv3 specification mentions the need for dsb after a read
from the ICC_IAR1_EL1 register:
4.1.1 Physical CPU Interface:
The effects of reading ICC_IAR0_EL1 and ICC_IAR1_EL1
on the state of a returned INTID are not guaranteed
to be visible until after the execution of a DSB.
Not having this could result in missed interrupts, so let's add the
required barrier.
[Marc: fixed commit message]
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
EOImode1 is only used for the root controller and hence only the root
controller uses the eoimode1 functions for handling interrupts. However,
if the root controller supports EOImode1, then the EOImodeNS bit will be
set for all GICs, enabling EOImode1. This is not what we want and this
causes interrupts on non-root GICs to only be dropped in priority but
never deactivated. Therefore, only set the EOImodeNS bit for the root
controller.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Setting the affinity of an IRQ, it only applicable for the root
interrupt controller and so only populate this operator for the root
controller.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Calling component_add() may result in the completion of a set of
devices, which will try to bring up a master. In bringing the master
up, we populate its match array with the current set of children.
If binding any of the devices fails, component_add() itself will fail,
free the struct component entry, and return to the caller. The
now-freed entry is never removed from the master's match array, and
will later be used in a futile attempt to bind to freed memory.
Bring component_add's behaviour on failure to bring up a master into
line with component_del by removing the (to-be-freed) component from
the master's match array.
The specific case which broke was:
- rockchip_drm_drv adds a component master
- dwhdmi_rockchip adds a child component in probe (master incomplete)
- rockchip_drm_vop adds two children in probe, which completes the
set
- inside component_add, we try to bring up the master, having
populated the master's match array, and fail with EPROBE_DEFER from
dwhdmi_rockchip; we delete the putative component
- rockchip_drm_vop's probe fails and returns EPROBE_DEFER
- we later re-probe rockchip_drm_vop and add the component; the
master is complete, so we attempt to bring it up again
- walking the match array, we find the previous child, whose master
pointer doesn't match (as it has been freed in the meantime)
- rockchip_drm_vop probe fails, and will never be attempted again
Fixes: ffc30b74fd6d01588bd3fdebc3b1acc0857e6fc8
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Fixes: fb3269b ("qla2xxx: Add selective command queuing")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Fixes: fb3269b ("qla2xxx: Add selective command queuing")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes an incorrect return of zero from the new
unmap_zeroes_data_store() configfs store attribute handler
introduced in v4.5-rc1, to use the correct 'count' bytes
return value.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When ctx access is used, the kernel often needs to expand/rewrite
instructions, so after that patching, branch offsets have to be
adjusted for both forward and backward jumps in the new eBPF program,
but for backward jumps it fails to account the delta. Meaning, for
example, if the expansion happens exactly on the insn that sits at
the jump target, it doesn't fix up the back jump offset.
Analysis on what the check in adjust_branches() is currently doing:
/* adjust offset of jmps if necessary */
if (i < pos && i + insn->off + 1 > pos)
insn->off += delta;
else if (i > pos && i + insn->off + 1 < pos)
insn->off -= delta;
First condition (forward jumps):
Before: After:
insns[0] insns[0]
insns[1] <--- i/insn insns[1] <--- i/insn
insns[2] <--- pos insns[P] <--- pos
insns[3] insns[P] `------| delta
insns[4] <--- target_X insns[P] `-----|
insns[5] insns[3]
insns[4] <--- target_X
insns[5]
First case is if we cross pos-boundary and the jump instruction was
before pos. This is handeled correctly. I.e. if i == pos, then this
would mean our jump that we currently check was the patchlet itself
that we just injected. Since such patchlets are self-contained and
have no awareness of any insns before or after the patched one, the
delta is correctly not adjusted. Also, for the second condition in
case of i + insn->off + 1 == pos, means we jump to that newly patched
instruction, so no offset adjustment are needed. That part is correct.
Second condition (backward jumps):
Before: After:
insns[0] insns[0]
insns[1] <--- target_X insns[1] <--- target_X
insns[2] <--- pos <-- target_Y insns[P] <--- pos <-- target_Y
insns[3] insns[P] `------| delta
insns[4] <--- i/insn insns[P] `-----|
insns[5] insns[3]
insns[4] <--- i/insn
insns[5]
Second interesting case is where we cross pos-boundary and the jump
instruction was after pos. Backward jump with i == pos would be
impossible and pose a bug somewhere in the patchlet, so the first
condition checking i > pos is okay only by itself. However, i +
insn->off + 1 < pos does not always work as intended to trigger the
adjustment. It works when jump targets would be far off where the
delta wouldn't matter. But, for example, where the fixed insn->off
before pointed to pos (target_Y), it now points to pos + delta, so
that additional room needs to be taken into account for the check.
This means that i) both tests here need to be adjusted into pos + delta,
and ii) for the second condition, the test needs to be <= as pos
itself can be a target in the backjump, too.
Fixes: 9bac3d6d548e ("bpf: allow extended BPF programs access skb fields")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the FLL is in pseudo-fractional mode there is an additional
limit on fref based on the fratio, to prevent aliasing around the
Nyquist frequency. If fref exceeds this limit the refclk divider
must be increased and the calculation tried again until a suitable
combination of fref and fratio is found or we have to fall back to
integer mode.
This patch also adds some debug log prints around this code.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Otherwise we could try to evict overlapping userptr BOs in get_user_pages(),
leading to a possible circular locking dependency.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
An arbitrary amount of time can pass between spin_unlock and
radeon_fence_wait_any, so we need to ensure that nobody frees the
fences from under us.
Based on the analogous fix for amdgpu.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
|
Ivan T. Ivanov
Simon Appleby
Marek Szyprowski
Cristian Birsan
Andrzej Hajda
Geert Uytterhoeven
Tang, Jianqiang
Vardan Mikayelyan
John Youn
Linus Torvalds
Andrey Konovalov
Leon Romanovsky
Alex Estrin
Ryan Ware
Vineet Gupta
Andrew Morton
Dan Williams
Vineet Gupta
Rasmus Villemoes
Kirill A. Shutemov
Jason A. Donenfeld
Randy Dunlap
Yang Shi
Eran Ben Elisha
Ulf Hansson
Javi Merino
David Sterba
Linus Walleij
Adrian Hunter
Daniel Wagner
Tirumalesh Chalamarla
Jon Hunter
Daniel Stone
Quinn Tran
Nicholas Bellinger
Daniel Borkmann
Richard Fitzgerald
Christian König
Nicolai Hähnle