| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is an issue about pop noise in NAU88L25 as follows.
Issue 54078: Chell_headphone pop back from S3
(1)Play directly to hw, bypassing CRAS:
sox -b 16 -n -t alsa hw:0,0 synth sine 200 sine 200
(2)Close lid or powerd_dbus_suspend, then press a key to resume.
(3)no audio after resume
(4)Audio will be back after close then reopen the pcm device.
After verification, we find one defect is that semaphone lock is not
long enough and expired. In this situation, the playback comes back
early but pauses a while to wait for the crosstalk detection done.
But the detection spends too much time and lock time is up. Therefore,
the playback and jack detection sequence interfere to each other.
That breaks sequence and makes noise. The driver extends the lock
time for the issue.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver fine-tune some parameters to improve FLL performance.
Those items have description as follow.
(1)ICTRL_LATCH: FLL DSP speed capability control
When FLL running at high frequency with long decimal number, DSP needs
to operate at high speed. FLL DSP can optimize between performance and
power consumption by ICTRL_LATCH.(111 has highest power consumption.)
The default setting can be used to reduce power.
(2)CUTOFF500: loop filter cutoff frequency at 500Khz
It will give the best FLL performance but highest power consumption
to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL
output noise, especially,(DCO frequency)/(FLL input reference frequency)
is not a integer.
(3)GAIN_ERR: FLL gain error correction threshold setting
The threshold is comparison between DCO and target frequency.
The value 1111 has the most sensitive threshold, that is, 1111 can have
the most accurate DCO to target frequency. However, the gain error setting
conditionally and inversely depends on FLL input reference clock rate.
Higher FLL reference input frequency can only set lower gain error, such
as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL
reference input is from Frame Sync, 48KHz, higher error gain can apply
such as 1111.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Over Sampling Rate (OSR) is defined as CLK_ADC frequency divided by the
audio sample rate (Fs).
OSR = CLK_ADC / FS
The available OSRs are 32, 64, 128 or 256. Note that the OSR and Fs
values must be selected such that the maximum frequency of CLK_ADC
is less than 6.144 MHz. It is recommended to match the relationship
between OSR and clock SRC according to following Table.
ADC_RATE: 00(OSR=32) | CLK_ADC_SRC: 11(CODEC 1/8)
ADC_RATE: 01(OSR=64) | CLK_ADC_SRC: 10(CODEC1/4)
ADC_RATE: 10(OSR=128) | CLK_ADC_SRC: 01(CODEC 1/2)
ADC_RATE: 11(OSR=256) | CLK_ADC_SRC: 00(CODEC CLK)
The over sampling rate about DAC follows the same rule with ADCs.
The driver changes the OSR to 64 value when initiation for better FLL
performance and applies the dynamic SRC change by different OSR.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the short Frame Sync detection logic enabled, the logic will check the
short frame sync threshold. If frame sync is less than the setting;
for example, frame sync less than 252 MCLK, the short frame sync signal is
flagged, digital filter temporary mute and skip that data.
If the system was intended for sampling rate change which could create
temporary short frame sync and not enough MIPS to run the digital filter.
But the situation doesn't happen in ALSA architecure. Thus the Frame Sync
is always stable, then no require to do the detection. Therefore,
the dirver disables the function for better performance.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
score images fail to build as follows.
arch/score/kernel/traps.c: In function 'show_stack':
arch/score/kernel/traps.c:55:3: error:
implicit declaration of function '__get_user'
__get_user() is declared in asm/uaccess.h, which was previously included
through asm/module.h.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 88dd4a748da7 ("score: separate extable.h, switch module.h to it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
sb_wait_write()->percpu_rwsem_release() fools lockdep to avoid the
false-positives. Now that xfs was fixed by Dave's commit dbad7c993053
("xfs: stop holding ILOCK over filldir callbacks") we can remove it and
change freeze_super() and thaw_super() to run with s_writers.rw_sem locks
held; we add two trivial helpers for that, lockdep_sb_freeze_release()
and lockdep_sb_freeze_acquire().
xfstests-dev/check `grep -il freeze tests/*/???` does not trigger any
warning from lockdep.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than
frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which
drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering.
In this case thaw_super() will wrongly call s_op->unfreeze_fs() before
it was actually frozen, and call sb_freeze_unlock() which leads to the
unbalanced percpu_up_write(). Unfortunately lockdep can't detect this,
so this triggers misc BUG_ON()'s in kernel/rcu/sync.c.
Reported-and-tested-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
ovl_fill_super calls ovl_new_inode to create a root inode for the new
superblock before initializing sb->s_xattr. This wrongly causes
IOP_XATTR to be cleared in i_opflags of the new inode, causing SELinux
to log the following message:
SELinux: (dev overlay, type overlay) has no xattr support
Fix this by initializing sb->s_xattr and similar fields before calling
ovl_new_inode.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Both import_iovec() and rw_copy_check_uvector() take an array
(typically small and on-stack) which is used to hold an iovec array copy
from userspace. This is to avoid an expensive memory allocation in the
fast path (i.e. few iovec elements).
The caller may have to check whether these functions actually used
the provided buffer or allocated a new one -- but this differs between
the too. Let's just add a kernel doc to clarify what the semantics are
for each function.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
New mount option "idsfromsid" indicates to cifs.ko that
it should try to retrieve the uid and gid owner fields
from special sids. This patch adds the code to parse the owner
sids in the ACL to see if they match, and if so populate the
uid and/or gid from them. This is faster than upcalling for
them and asking winbind, and is a fairly common case, and is
also helpful when cifs.upcall and idmapping is not configured.
Signed-off-by: Steve French <steve.french@primarydata.com>
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
Add "idsfromsid" mount option to indicate to cifs.ko that it should
try to retrieve the uid and gid owner fields from special sids in the
ACL if present. This first patch just adds the parsing for the mount
option.
Signed-off-by: Steve French <steve.french@primarydata.com>
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
Add error handling support.
Register ib device with ib stack.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support for GSI over light L2.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add light L2 interface for RoCE.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Implement fastpath verbs like ib_send_post, ib_post_recv and ib_poll_cq.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support for user, dma and memory regions registration.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support for Queue Pair verbs which adds, deletes,
modifies and queries Queue Pairs.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support for protection domain and completion queue verbs.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support for ucontext, query port, add and del gid verbs.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Allocate and setup RoCE resources, interrupts and completion queues.
Adds device attributes.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Adds a skeletal implementation of the qed* RoCE driver -
basically the ability to communicate with the qede driver and
receive notifications from it regarding various init/exit events.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This easy-to-trigger warning shows up instantly when running
Trinity on a kernel with CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS disabled.
At most this should have been a printk, but the -EINVAL alone should be more
than adequate indicator that something isn't available.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14380/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Resulting in a complete removal of a function basically implementing the
inverse of vfs_readlink().
As a bonus, now the proper security hook is also called.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
This helper is for filesystems that want to read the symlink and are better
off with the get_link() interface (returning a char *) rather than the
readlink() interface (copy into a userspace buffer).
Also call the LSM hook for readlink (not get_link) since this is for
symlink reading not following.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
All filesystems that are backers for overlayfs would also use
generic_readlink(). Move this logic to the overlay itself, which is a nice
cleanup.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
We are already doing the same thing for an ordinary open case:
we can't keep read oplock on a file if we have mandatory byte-range
locks because pagereading can conflict with these locks on a server.
Fix it by setting oplock level to NONE.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
openFileList of tcon can be changed while cifs_reopen_file() is called
that can lead to an unexpected behavior when we return to the loop.
Fix this by introducing a temp list for keeping all file handles that
need to be reopen.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
We split the rawntlmssp authentication into negotiate and
authencate parts. We also clean up the code and add helpers.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
Add helper functions and split Kerberos authentication off
SMB2_sess_setup.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
/sys/module/cifs/parameters should display the three
other module load time configuration settings for cifs.ko
Signed-off-by: Germano Percossi <germano.percossi@citrix.com>
Signed-off-by: Steve French <steve.french@primarydata.com>
|
|
Cleanup some missing mem frees on some cifs ioctls, and
clarify others to make more obvious that no data is returned.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
|
|
Add ioctl to query previous versions of file
Allows listing snapshots on files on SMB3 mounts.
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
[CIFS] We had cases where we sent a SMB2/SMB3 setinfo request with all
timestamp (and DOS attribute) fields marked as 0 (ie do not change)
e.g. on chmod or chown.
Signed-off-by: Steve French <steve.french@primarydata.com>
CC: Stable <stable@vger.kernel.org>
|
|
The desired_perf is an abstract performance number. Its value should
be in the range of [lowest perf, highest perf] of CPPC.
The correct calculation is
desired_perf = freq * cppc_highest_perf / cppc_dmi_max_khz
And cppc_cpufreq_set_target() returns if desired_perf is exactly
the same with the old perf.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When I added the multicast flood control flag, I also added an attribute
for it for sysfs similar to other flags, but I forgot to add it to
brport_attrs.
Fixes: b6cb5ac8331b ("net: bridge: add per-port multicast flood flag")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev parameter passed to __axienet_device_reset() is not used inside
the function, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is supposed to loop 1000 times and then give up. The problem is
it's a post-op and after the loop we test if "loop" is zero when really
it would be -1. Fix this by making it a pre-op.
Fixes: 1b7c55c4538b ("liquidio: CN23XX queue manipulation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "vf_vlan_info" struct ends with a 2 byte struct hole so we have to
memset it to ensure that no stack information is revealed to user space.
Fixes: 79aab093a0b5 ('net: Update API for VF vlan protocol 802.1ad support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should clear out the padding and unused struct members so that we
don't expose stack information to userspace.
Fixes: fdb3accc2c15 ('tipc: add the ability to get UDP options via netlink')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e0d56fdd7342 was a bit aggressive removing l3mdev calls in
the IPv4 stack. If the fib_lookup fails we do not want to drop to
make_route if the oif is an l3mdev device.
Also reverts 19664c6a0009 ("net: l3mdev: Remove netif_index_is_l3_master")
which removed netif_index_is_l3_master.
Fixes: e0d56fdd7342 ("net: l3mdev: remove redundant calls")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy_start() is used to indicate the PHY is now ready to do its
work. The state is changed, normally to PHY_UP which means that both
the MAC and the PHY are ready.
If the phy driver is using polling, when the next poll happens, the
state machine notices the PHY is now in PHY_UP, and kicks off
auto-negotiation, if needed.
If however, the PHY is using interrupts, there is no polling. The phy
is stuck in PHY_UP until the next interrupt comes along. And there is
no reason for the PHY to interrupt.
Have phy_start() schedule the state machine to run, which both speeds
up the polling use case, and makes the interrupt use case actually
work.
This problems exists whenever there is a state change which will not
cause an interrupt. Trigger the state machine in these cases,
e.g. phy_error().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kyle Roeschley <kyle.roeschley@ni.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This should have been part of 40e084a506eb ('MIPS: Add uprobes support.').
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes: 40e084a506eb ("MIPS: Add uprobes support.")
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14392/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Baozeng Ding reported following KASAN splat :
BUG: KASAN: use-after-free in ip6_datagram_recv_specific_ctl+0x13f1/0x15c0 at addr ffff880029c84ec8
Read of size 1 by task poc/25548
Call Trace:
[<ffffffff82cf43c9>] dump_stack+0x12e/0x185 /lib/dump_stack.c:15
[< inline >] print_address_description /mm/kasan/report.c:204
[<ffffffff817ced3b>] kasan_report_error+0x48b/0x4b0 /mm/kasan/report.c:283
[< inline >] kasan_report /mm/kasan/report.c:303
[<ffffffff817ced9e>] __asan_report_load1_noabort+0x3e/0x40 /mm/kasan/report.c:321
[<ffffffff85c71da1>] ip6_datagram_recv_specific_ctl+0x13f1/0x15c0 /net/ipv6/datagram.c:687
[<ffffffff85c734c3>] ip6_datagram_recv_ctl+0x33/0x40
[<ffffffff85c0b07c>] do_ipv6_getsockopt.isra.4+0xaec/0x2150
[<ffffffff85c0c7f6>] ipv6_getsockopt+0x116/0x230
[<ffffffff859b5a12>] tcp_getsockopt+0x82/0xd0 /net/ipv4/tcp.c:3035
[<ffffffff855fb385>] sock_common_getsockopt+0x95/0xd0 /net/core/sock.c:2647
[< inline >] SYSC_getsockopt /net/socket.c:1776
[<ffffffff855f8ba2>] SyS_getsockopt+0x142/0x230 /net/socket.c:1758
[<ffffffff8685cdc5>] entry_SYSCALL_64_fastpath+0x23/0xc6
Memory state around the buggy address:
ffff880029c84d80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff880029c84e00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> ffff880029c84e80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff880029c84f00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff880029c84f80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
He also provided a syzkaller reproducer.
Issue is that ip6_datagram_recv_specific_ctl() expects to find IP6CB
data that was moved at a different place in tcp_v6_rcv()
This patch moves tcp_v6_restore_cb() up and calls it from
tcp_v6_do_rcv() when np->pktoptions is set.
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based upon v2 of Stephen's patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wiht the latest rework of the xen-netback driver, we get a warning
on ARM about the types passed into min():
drivers/net/xen-netback/rx.c: In function 'xenvif_rx_next_chunk':
include/linux/kernel.h:739:16: error: comparison of distinct pointer types lacks a cast [-Werror]
The reason is that XEN_PAGE_SIZE is not size_t here. There
is no actual bug, and we can easily avoid the warning using the
min_t() macro instead of min().
Fixes: eb1723a29b9a ("xen-netback: refactor guest rx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a problem when propagated the
failure of ptp_clock_register to open function.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The gmac 4.x version has not extended descriptors
(that are available on 3.x instead of).
While initializing the PTP module, the advanced PTP was
enabled in case of extended descriptors. This cannot be
applied for 4.x version where only the hardware capability
register has to show if the feature is present.
Patch also adds some extra netdev_(debug/inof) to better
dump the configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
John Hsu
Linus Torvalds
Guenter Roeck
Oleg Nesterov
Vivek Goyal
Vegard Nossum
Steve French
Ram Amrani
Dave Jones
Ralf Baechle
Miklos Szeredi
Pavel Shilovsky
Sachin Prabhu
Germano Percossi
Hoan Tran
Nikolay Aleksandrov
Tobias Klauser
Dan Carpenter
David Ahern
Andrew Lunn
Eric Dumazet
David S. Miller
Arnd Bergmann
Giuseppe CAVALLARO