aboutsummaryrefslogtreecommitdiffstats
path: root/tools/perf/scripts/python/call-graph-from-postgresql.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2017-08-18ARM: dts: versatile: fix PCI bus dtc warningsRob Herring1-1/+1
dtc recently added PCI bus checks. Fix these warnings. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-08-18ARM: dts: spear13xx: fix PCI bus dtc warningsRob Herring2-0/+4
dtc recently added PCI bus checks. Fix these warnings. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-08-19ARM: sun8i: a83t: h8homlet-v2: Enable USB portsChen-Yu Tsai1-0/+29
The h8homlet board has the A83T's standard USB 1.1/2.0 host pair routed to a USB host port on the board. The other USB host port is routed to USB OTG controller. Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2017-08-19ARM: sun8i: a83t: cubietruck-plus: Enable onboard USB peripheralsChen-Yu Tsai1-5/+44
The Cubietruck-plus has a GL830 USB-to-SATA bridge connected to EHCI0, and a USB3503 HSIC USB 2.0 hub connected to EHCI1. The USB3503's I2C control interface is not connected. This patch enables both EHCI controllers, adds a device node for the USB hub, and includes sunxi-common-regulators.dtsi for the VBUS regulators. The existing reg_vcc3v3 is dropped as it is also available in the set of common regulators. Other unused regulators are disabled. Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2017-08-19ARM: sun8i: a83t: Add device node for USB OTG controllerChen-Yu Tsai1-0/+14
The USB OTG controller found on the A83T is compatible with the one found on the A33. Add a device node for it. Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2017-08-19ARM: sun8i: a83t: Add USB PHY and host device nodesChen-Yu Tsai1-0/+62
The A83T has 3 USB PHYs, 1 for USB OTG, 1 for standard USB 2.0, 1 for USB HSIC. EHCI0/OHCI0 are the standard USB host pair, while EHCI1 is the host controller for HSIC. OTG is not added yet. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-17ARM: BCM53573: Specify ports for USB LED for Tenda AC9Rafał Miłecki2-0/+6
This uses trigger-sources documented in commit 80dc6e1cd85fc ("dt-bindings: leds: document new trigger-sources property") to specify USB ports. Such an information can be used by operating system to setup LEDs behavior. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Add generic-ehci/ohci nodesRaveendra Padasalagi1-0/+14
Add dt nodes for generic-ehci/ohci host controller. Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphnScott Branden1-2/+5
Use serial0 alias to select stdout-path on Cygnus bcm911360_entphon board. Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Add additional peripherals to dtsiJonathan Richardson1-0/+102
Add nodes for peripherals in Cygnus dtsi: sdhci, keypad, spi, dma, pinmux configs. Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Enable Performance Monitoring UnitJason Uy1-0/+5
Add PMU capability to Cygnus so trace and performance profiling can be used. Signed-off-by: Jason Uy <jason.uy@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: place v3d in proper address ordered locationScott Branden1-13/+13
Move v3d devicetree node to proper address ordered location in Cygnus dtsi. Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: cygnus: Fix incorrect UART2 register baseRay Jui1-1/+1
Fix incorrect Cygnus UART2 register base. Fixes: 0f0b21a83ad2 ("ARM: dts: Move all Cygnus peripherals into axi bus") Signed-off-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-08-17ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpioAdam Ford1-1/+1
Fixes commit 687c27676151 ("ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit") This patch corrects an issue where the cd-gpios was improperly setup using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-17ARM: dts: am57xx-beagle-x15: Add support for rev CRobert Nelson2-0/+40
Latest update to the BeagleBoard-X15 platform (revision C). This board contains a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when running at 1000 Mbps speeds. This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom: [BBRDX15_C.001731PX150249] Rev C is now in full production and boards are available for end users. https://beagleboard.org/x15 https://github.com/beagleboard/beagleboard-x15/ Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Nishanth Menon <nm@ti.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Drew Fustini <drew@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-17ARM: tegra: Enable UDC on AC100Dmitry Osipenko1-0/+2
Override the compatible string of the first USB controller to enable device mode. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Tested-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: tegra: Enable UDC on Jetson TK1Thierry Reding1-1/+11
Override the compatible string of the first USB controller to enable device mode. Tested-by: Nicolas Chauvet <kwizart@gmail.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: tegra: Enable UDC on DalmoreThierry Reding1-0/+10
Override the compatible string of the first USB controller to enable device mode. Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: tegra: Enable UDC on BeaverThierry Reding1-0/+10
Override the compatible string of the first USB controller to enable device mode. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2017-08-17ARM: dts: r8a7791: Use R-Car SATA Gen2 fallback compat stringSimon Horman1-2/+2
Use newly added R-Car SATA Gen2 fallback compat string in the DT of the r8a7791 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before the fallback compat string is considered. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-08-17ARM: dts: r8a7790: Use R-Car SATA Gen2 fallback compat stringSimon Horman1-2/+2
Use newly added R-Car SATA Gen2 fallback compat string in the DT of the r8a7790 SoC. This should have no run-time effect as the driver matches against the per-SoC compat string before the fallback compat string is considered. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-08-17ARM: dts: r8a7743: Add OPP table for frequency scalingBiju Das1-0/+9
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver. - clock-latency = 300 us Approximate worst-case latency to do clock transition for every OPPs. Using an arbitrary safe value similar to r8a7791(R-Car M2) Soc. - operating-points = < kHz - uV > List of 6 operating points. All of them are using the same voltage since DVS is not supported in RZ/G1 Soc. Note:This also fixes the below errors seen on kernel logs [ 0.876877] cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19) [ 0.883727] cpu cpu1: cpufreq_init: failed to get clk: -2 Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17ARM: dts: r8a7743: Add APMU node and second CPU coreBiju Das1-0/+16
Add DT nodes for the Advanced Power Management Unit (APMU) and the second CPU core. Use the enable-method to point out that the APMU should be used for SMP support. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17dt-bindings: apmu: Document r8a7743 supportBiju Das1-1/+2
Document APMU and SMP enable method for RZ/G1M (also known as r8a7743) SoC. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17ARM: shmobile: document iW-RainboW-G22D SODIMM SOM Development PlatformFabrizio Castro1-0/+2
Document the iW-RainboW-G22D device tree bindings. It is just a placeholder for the time being, the actual implementation is not available yet. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Chris Paterson <chris.paterson2@renesas.com> Reviewed-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17ARM: shmobile: document iW-RainboW-G22M-SM SODIMM System on ModuleFabrizio Castro1-0/+2
Document the iW-RainboW-G22M-SM SODIMM System on Module device tree bindings. It is just a placeholder for the time being, the actual implementation is not available yet. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Chris Paterson <chris.paterson2@renesas.com> Reviewed-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-17ARM: dts: koelsch: Add CEC clock for HDMI transmitterHans Verkuil1-0/+8
The adv7511 on the Koelsch board has a 12 MHz fixed clock for the CEC block. Specify this in the dts to enable CEC support. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-08-16ARM: dts: dra71-evm: Add pinmux configuration for MMCKishon Vijay Abraham I1-0/+14
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra71-evm.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-16ARM: dts: dra72-evm-revc: Add pinmux configuration for MMCKishon Vijay Abraham I1-0/+14
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra72-evm-revc.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-16ARM: dts: dra72-evm: Add pinmux configuration for MMCKishon Vijay Abraham I1-0/+14
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra72-evm.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-16ARM: dts: am572x-idk: Add pinmux configuration for MMCKishon Vijay Abraham I1-0/+19
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74x SoC and use it in the pinctrl properties of MMC devicetree nodes present in am572x-idk.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-16ARM: dts: am571x-idk: Add pinmux configuration for MMCKishon Vijay Abraham I1-0/+19
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in am571x-idk.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-16ARM: dts: am57xx-idk: Move common MMC/SD properties to common fileSekhar Nori3-15/+8
AM572x IDK and AM571x IDK boards have equivalent design of how SD card and eMMC are connected. The two EVMs mainly differ in IOdelay configuration needed (because of difference in SoC used). Move the common properties to am57xx-idk-common.dtsi file which is common for both EVMs. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-16ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMCKishon Vijay Abraham I3-28/+27
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74 SoC and use it in the pinctrl properties of MMC devicetree nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-08-16ARM: dts: dra7-evm: Add pinmux configuration for MMCKishon Vijay Abraham I1-4/+18
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra7-evm. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>