| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Due to the reference clock comes from 26M oscillator directly
on mt8173, and it is a fixed-clock in DTS which always turned
on, we ignore it before. But on some platforms, it comes
from PLL, and need be controlled, so here add it, no matter
it is a fixed-clock or not.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The condition modex % 16 cannot be true when modex value is equal to 640
The condition du & 0xff cannot be true when du value is equal to 0x1400
Addresses-Coverity-Id: 101163
Addresses-Coverity-Id: 744373
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove this line of code because devnum is overwritten before it can be used.
This could happen if line of code 609 (goto try_again;) is executed. Otherwise,
devnum is never used again.
Addresses-Coverity-ID: 1226870
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
do_generic_file_read() can be told to perform a large request from
userspace. If the system is under OOM and the reading task is the OOM
victim then it has an access to memory reserves and finishing the full
request can lead to the full memory depletion which is dangerous. Make
sure we rather go with a short read and allow the killed task to
terminate.
Link: http://lkml.kernel.org/r/20170201092706.9966-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tetsuo has noticed that an OOM stress test which performs large write
requests can cause the full memory reserves depletion. He has tracked
this down to the following path
__alloc_pages_nodemask+0x436/0x4d0
alloc_pages_current+0x97/0x1b0
__page_cache_alloc+0x15d/0x1a0 mm/filemap.c:728
pagecache_get_page+0x5a/0x2b0 mm/filemap.c:1331
grab_cache_page_write_begin+0x23/0x40 mm/filemap.c:2773
iomap_write_begin+0x50/0xd0 fs/iomap.c:118
iomap_write_actor+0xb5/0x1a0 fs/iomap.c:190
? iomap_write_end+0x80/0x80 fs/iomap.c:150
iomap_apply+0xb3/0x130 fs/iomap.c:79
iomap_file_buffered_write+0x68/0xa0 fs/iomap.c:243
? iomap_write_end+0x80/0x80
xfs_file_buffered_aio_write+0x132/0x390 [xfs]
? remove_wait_queue+0x59/0x60
xfs_file_write_iter+0x90/0x130 [xfs]
__vfs_write+0xe5/0x140
vfs_write+0xc7/0x1f0
? syscall_trace_enter+0x1d0/0x380
SyS_write+0x58/0xc0
do_syscall_64+0x6c/0x200
entry_SYSCALL64_slow_path+0x25/0x25
the oom victim has access to all memory reserves to make a forward
progress to exit easier. But iomap_file_buffered_write and other
callers of iomap_apply loop to complete the full request. We need to
check for fatal signals and back off with a short write instead.
As the iomap_apply delegates all the work down to the actor we have to
hook into those. All callers that work with the page cache are calling
iomap_write_begin so we will check for signals there. dax_iomap_actor
has to handle the situation explicitly because it copies data to the
userspace directly. Other callers like iomap_page_mkwrite work on a
single page or iomap_fiemap_actor do not allocate memory based on the
given len.
Fixes: 68a9f5e7007c ("xfs: implement iomap based buffered write path")
Link: http://lkml.kernel.org/r/20170201092706.9966-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Reading a sysfs "memoryN/valid_zones" file leads to the following oops
when the first page of a range is not backed by struct page.
show_valid_zones() assumes that 'start_pfn' is always valid for
page_zone().
BUG: unable to handle kernel paging request at ffffea017a000000
IP: show_valid_zones+0x6f/0x160
This issue may happen on x86-64 systems with 64GiB or more memory since
their memory block size is bumped up to 2GiB. [1] An example of such
systems is desribed below. 0x3240000000 is only aligned by 1GiB and
this memory block starts from 0x3200000000, which is not backed by
struct page.
BIOS-e820: [mem 0x0000003240000000-0x000000603fffffff] usable
Since test_pages_in_a_zone() already checks holes, fix this issue by
extending this function to return 'valid_start' and 'valid_end' for a
given range. show_valid_zones() then proceeds with the valid range.
[1] 'Commit bdee237c0343 ("x86: mm: Use 2GB memory block size on
large-memory x86-64 systems")'
Link: http://lkml.kernel.org/r/20170127222149.30893-3-toshi.kani@hpe.com
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org> [4.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "fix a kernel oops when reading sysfs valid_zones", v2.
A sysfs memory file is created for each 2GiB memory block on x86-64 when
the system has 64GiB or more memory. [1] When the start address of a
memory block is not backed by struct page, i.e. a memory range is not
aligned by 2GiB, reading its 'valid_zones' attribute file leads to a
kernel oops. This issue was observed on multiple x86-64 systems with
more than 64GiB of memory. This patch-set fixes this issue.
Patch 1 first fixes an issue in test_pages_in_a_zone(), which does not
test the start section.
Patch 2 then fixes the kernel oops by extending test_pages_in_a_zone()
to return valid [start, end).
Note for stable kernels: The memory block size change was made by commit
bdee237c0343 ("x86: mm: Use 2GB memory block size on large-memory x86-64
systems"), which was accepted to 3.9. However, this patch-set depends
on (and fixes) the change to test_pages_in_a_zone() made by commit
5f0f2887f4de ("mm/memory_hotplug.c: check for missing sections in
test_pages_in_a_zone()"), which was accepted to 4.4.
So, I recommend that we backport it up to 4.4.
[1] 'Commit bdee237c0343 ("x86: mm: Use 2GB memory block size on
large-memory x86-64 systems")'
This patch (of 2):
test_pages_in_a_zone() does not check 'start_pfn' when it is aligned by
section since 'sec_end_pfn' is set equal to 'pfn'. Since this function
is called for testing the range of a sysfs memory file, 'start_pfn' is
always aligned by section.
Fix it by properly setting 'sec_end_pfn' to the next section pfn.
Also make sure that this function returns 1 only when the range belongs
to a zone.
Link: http://lkml.kernel.org/r/20170127222149.30893-2-toshi.kani@hpe.com
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Banman <abanman@sgi.com>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@vger.kernel.org> [4.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some versions of ARM GCC compiler such as Android toolchain throws in a
'-fpic' flag by default. This causes the gcc-goto check script to fail
although some config would have '-fno-pic' flag in the KBUILD_CFLAGS.
This patch passes the KBUILD_CFLAGS to the check script so that the
script does not rely on the default config from different compilers.
Link: http://lkml.kernel.org/r/20170120234329.78868-1-dtwlin@google.com
Signed-off-by: David Lin <dtwlin@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Michal Marek <mmarek@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Syzkaller fuzzer managed to trigger this:
BUG: sleeping function called from invalid context at mm/shmem.c:852
in_atomic(): 1, irqs_disabled(): 0, pid: 529, name: khugepaged
3 locks held by khugepaged/529:
#0: (shrinker_rwsem){++++..}, at: [<ffffffff818d7ef1>] shrink_slab.part.59+0x121/0xd30 mm/vmscan.c:451
#1: (&type->s_umount_key#29){++++..}, at: [<ffffffff81a63630>] trylock_super+0x20/0x100 fs/super.c:392
#2: (&(&sbinfo->shrinklist_lock)->rlock){+.+.-.}, at: [<ffffffff818fd83e>] spin_lock include/linux/spinlock.h:302 [inline]
#2: (&(&sbinfo->shrinklist_lock)->rlock){+.+.-.}, at: [<ffffffff818fd83e>] shmem_unused_huge_shrink+0x28e/0x1490 mm/shmem.c:427
CPU: 2 PID: 529 Comm: khugepaged Not tainted 4.10.0-rc5+ #201
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
shmem_undo_range+0xb20/0x2710 mm/shmem.c:852
shmem_truncate_range+0x27/0xa0 mm/shmem.c:939
shmem_evict_inode+0x35f/0xca0 mm/shmem.c:1030
evict+0x46e/0x980 fs/inode.c:553
iput_final fs/inode.c:1515 [inline]
iput+0x589/0xb20 fs/inode.c:1542
shmem_unused_huge_shrink+0xbad/0x1490 mm/shmem.c:446
shmem_unused_huge_scan+0x10c/0x170 mm/shmem.c:512
super_cache_scan+0x376/0x450 fs/super.c:106
do_shrink_slab mm/vmscan.c:378 [inline]
shrink_slab.part.59+0x543/0xd30 mm/vmscan.c:481
shrink_slab mm/vmscan.c:2592 [inline]
shrink_node+0x2c7/0x870 mm/vmscan.c:2592
shrink_zones mm/vmscan.c:2734 [inline]
do_try_to_free_pages+0x369/0xc80 mm/vmscan.c:2776
try_to_free_pages+0x3c6/0x900 mm/vmscan.c:2982
__perform_reclaim mm/page_alloc.c:3301 [inline]
__alloc_pages_direct_reclaim mm/page_alloc.c:3322 [inline]
__alloc_pages_slowpath+0xa24/0x1c30 mm/page_alloc.c:3683
__alloc_pages_nodemask+0x544/0xae0 mm/page_alloc.c:3848
__alloc_pages include/linux/gfp.h:426 [inline]
__alloc_pages_node include/linux/gfp.h:439 [inline]
khugepaged_alloc_page+0xc2/0x1b0 mm/khugepaged.c:750
collapse_huge_page+0x182/0x1fe0 mm/khugepaged.c:955
khugepaged_scan_pmd+0xfdf/0x12a0 mm/khugepaged.c:1208
khugepaged_scan_mm_slot mm/khugepaged.c:1727 [inline]
khugepaged_do_scan mm/khugepaged.c:1808 [inline]
khugepaged+0xe9b/0x1590 mm/khugepaged.c:1853
kthread+0x326/0x3f0 kernel/kthread.c:227
ret_from_fork+0x31/0x40 arch/x86/entry/entry_64.S:430
The iput() from atomic context was a bad idea: if after igrab() somebody
else calls iput() and we left with the last inode reference, our iput()
would lead to inode eviction and therefore sleeping.
This patch should fix the situation.
Link: http://lkml.kernel.org/r/20170131093141.GA15899@node.shutemov.name
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After much waiting I finally reproduced a KASAN issue, only to find my
trace-buffer empty of useful information because it got spooled out :/
Make kasan_report honour the /proc/sys/kernel/traceoff_on_warning
interface.
Link: http://lkml.kernel.org/r/20170125164106.3514-1-aryabinin@virtuozzo.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add zswap_init_failed bool that prevents changing any of the module
params, if init_zswap() fails, and set zswap_enabled to false. Change
'enabled' param to a callback, and check zswap_init_failed before
allowing any change to 'enabled', 'zpool', or 'compressor' params.
Any driver that is built-in to the kernel will not be unloaded if its
init function returns error, and its module params remain accessible for
users to change via sysfs. Since zswap uses param callbacks, which
assume that zswap has been initialized, changing the zswap params after
a failed initialization will result in WARNING due to the param
callbacks expecting a pool to already exist. This prevents that by
immediately exiting any of the param callbacks if initialization failed.
This was reported here:
https://marc.info/?l=linux-mm&m=147004228125528&w=4
And fixes this WARNING:
[ 429.723476] WARNING: CPU: 0 PID: 5140 at mm/zswap.c:503 __zswap_pool_current+0x56/0x60
The warning is just noise, and not serious. However, when init fails,
zswap frees all its percpu dstmem pages and its kmem cache. The kmem
cache might be serious, if kmem_cache_alloc(NULL, gfp) has problems; but
the percpu dstmem pages are definitely a problem, as they're used as
temporary buffer for compressed pages before copying into place in the
zpool.
If the user does get zswap enabled after an init failure, then zswap
will likely Oops on the first page it tries to compress (or worse, start
corrupting memory).
Fixes: 90b0fc26d5db ("zswap: change zpool/compressor at runtime")
Link: http://lkml.kernel.org/r/20170124200259.16191-2-ddstreet@ieee.org
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Reported-by: Marcin Miroslaw <marcin@mejor.pl>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'm leaving my job at Red Hat, this email address will stop working next week.
Update it to one that I will have access to later.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Currently, under certain circumstances vhost_init_is_le does just a part
of the initialization job, and depends on vhost_reset_is_le being called
too. For this reason vhost_vq_init_access used to call vhost_reset_is_le
when vq->private_data is NULL. This is not only counter intuitive, but
also real a problem because it breaks vhost_net. The bug was introduced to
vhost_net with commit 2751c9882b94 ("vhost: cross-endian support for
legacy devices"). The symptom is corruption of the vq's used.idx field
(virtio) after VHOST_NET_SET_BACKEND was issued as a part of the vhost
shutdown on a vq with pending descriptors.
Let us make sure the outcome of vhost_init_is_le never depend on the state
it is actually supposed to initialize, and fix virtio_net by removing the
reset from vhost_vq_init_access.
With the above, there is no reason for vhost_reset_is_le to do just half
of the job. Let us make vhost_reset_is_le reinitialize is_le.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reported-by: Michael A. Tebolt <miket@us.ibm.com>
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: commit 2751c9882b94 ("vhost: cross-endian support for legacy devices")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Michael A. Tebolt <miket@us.ibm.com>
|
|
This reverts commit c7070619f3408d9a0dffbed9149e6f00479cf43b.
This has been shown to regress on some ARM systems:
by forcing on DMA API usage for ARM systems, we have inadvertently
kicked open a hornets' nest in terms of cache-coherency. Namely that
unless the virtio device is explicitly described as capable of coherent
DMA by firmware, the DMA APIs on ARM and other DT-based platforms will
assume it is non-coherent. This turns out to cause a big problem for the
likes of QEMU and kvmtool, which generate virtio-mmio devices in their
guest DTs but neglect to add the often-overlooked "dma-coherent"
property; as a result, we end up with the guest making non-cacheable
accesses to the vring, the host doing so cacheably, both talking past
each other and things going horribly wrong.
We are working on a safer work-around.
Fixes: c7070619f340 ("vring: Force use of DMA API for ARM-based systems with legacy devices")
Reported-by: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The function order_base_2() is defined (according to the comment block)
as returning zero on input zero, but subsequently passes the input into
roundup_pow_of_two(), which is explicitly undefined for input zero.
This has gone unnoticed until now, but optimization passes in GCC 7 may
produce constant folded function instances where a constant value of
zero is passed into order_base_2(), resulting in link errors against the
deliberately undefined '____ilog2_NaN'.
So update order_base_2() to adhere to its own documented interface.
[ See
http://marc.info/?l=linux-kernel&m=147672952517795&w=2
and follow-up discussion for more background. The gcc "optimization
pass" is really just broken, but now the GCC trunk problem seems to
have escaped out of just specially built daily images, so we need to
work around it in mainline. - Linus ]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Saving unsupported state prevents migration when the new host does not
support a XSAVE feature of the original host, even if the feature is not
exposed to the guest.
We've masked host features with guest-visible features before, with
4344ee981e21 ("KVM: x86: only copy XSAVE state for the supported
features") and dropped it when implementing XSAVES. Do it again.
Fixes: df1daba7d1cb ("KVM: x86: support XSAVES usage in the host")
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
The previous patch introduced a separate inline asm version of the
krcrctab declaration template for use with 64-bit architectures, which
cannot refer to ELF symbols using 32-bit quantities.
This declaration should be equivalent to the C one for 32-bit
architectures, but just in case - unify them in a separate patch, which
can simply be dropped if it turns out to break anything.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The modversion symbol CRCs are emitted as ELF symbols, which allows us
to easily populate the kcrctab sections by relying on the linker to
associate each kcrctab slot with the correct value.
This has a couple of downsides:
- Given that the CRCs are treated as memory addresses, we waste 4 bytes
for each CRC on 64 bit architectures,
- On architectures that support runtime relocation, a R_<arch>_RELATIVE
relocation entry is emitted for each CRC value, which identifies it
as a quantity that requires fixing up based on the actual runtime
load offset of the kernel. This results in corrupted CRCs unless we
explicitly undo the fixup (and this is currently being handled in the
core module code)
- Such runtime relocation entries take up 24 bytes of __init space
each, resulting in a x8 overhead in [uncompressed] kernel size for
CRCs.
Switching to explicit 32 bit values on 64 bit architectures fixes most
of these issues, given that 32 bit values are not treated as quantities
that require fixing up based on the actual runtime load offset. Note
that on some ELF64 architectures [such as PPC64], these 32-bit values
are still emitted as [absolute] runtime relocatable quantities, even if
the value resolves to a build time constant. Since relative relocations
are always resolved at build time, this patch enables MODULE_REL_CRCS on
powerpc when CONFIG_RELOCATABLE=y, which turns the absolute CRC
references into relative references into .rodata where the actual CRC
value is stored.
So redefine all CRC fields and variables as u32, and redefine the
__CRC_SYMBOL() macro for 64 bit builds to emit the CRC reference using
inline assembler (which is necessary since 64-bit C code cannot use
32-bit types to hold memory addresses, even if they are ultimately
resolved using values that do not exceed 0xffffffff). To avoid
potential problems with legacy 32-bit architectures using legacy
toolchains, the equivalent C definition of the kcrctab entry is retained
for 32-bit architectures.
Note that this mostly reverts commit d4703aefdbc8 ("module: handle ppc64
relocating kcrctabs when CONFIG_RELOCATABLE=y")
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This add the kbuild infrastructure that will allow architectures to emit
vmlinux symbol CRCs as 32-bit offsets to another location in the kernel
where the actual value is stored. This works around problems with CRCs
being mistaken for relocatable symbols on kernels that self relocate at
runtime (i.e., powerpc with CONFIG_RELOCATABLE=y)
For the kbuild side of things, this comes down to the following:
- introducing a Kconfig symbol MODULE_REL_CRCS
- adding a -R switch to genksyms to instruct it to emit the CRC symbols
as references into the .rodata section
- making modpost distinguish such references from absolute CRC symbols
by the section index (SHN_ABS)
- making kallsyms disregard non-absolute symbols with a __crc_ prefix
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes the following sparse warning:
drivers/usb/musb/musb_dsps.c:270:6: warning:
symbol 'dsps_musb_clear_ep_rxintr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allwinner H3/V3s features a variant of MUSB controller, which lacks one
endpoint.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[b-liu@ti.com: added usb: to commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for arm
architecture.
File size before: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4141 400 8 4549 11c5 usb/musb/omap2430.o
File size after: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4333 200 8 4541 11bd usb/musb/omap2430.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
[b-liu@ti.com: added omap2430 in commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We can now configure the PMIC interrupt to provide us VBUS
events. In that case we don't need to constantly poll the
status and can make it optional. This is only wired up
for the mini-B interface on beaglebone.
Note that eventually we should get also the connect status
for the host interface when the am335x internal PM coprocessor
provides us with an IRQ chip. For now, we still need to poll
for the host mode status.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CONFIG_PM_SLEEP is disabled, SIMPLE_DEV_PM_OPS does not use
bfin_resume and bfin_suspend even if CONFIG_PM is enabled:
drivers/usb/musb/blackfin.c:602:12: warning: ‘bfin_resume’ defined but
not used [-Wunused-function]
static int bfin_resume(struct device *dev)
^~~~~~~~~~~
drivers/usb/musb/blackfin.c:585:12: warning: ‘bfin_suspend’ defined but
not used [-Wunused-function]
static int bfin_suspend(struct device *dev)
^~~~~~~~~~~~
The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However it is better to mark these functions as __maybe_unused.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dsps glue uses PLATFORM_DEVID_AUTO when creating the musb-hdrc
platform devices, this causes that the id will change in each system
depending on the order of driver probe, the order of the usb instances
defined in device-tree, or the list of enabled devices which use also
PLATFORM_DEVID_AUTO in kernel config. This id inconsistency causes
trouble in shell scripting or user guide documentation.
So switch it to static id, starting from 0 to the musb instance with
lower MMR offset. This scheme is also aligned to the naming in the SoC.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on the musb ug, force_host bit is allowed to be set along with
force_hs or force_fs bit.
It could help to implement forced host mode via testmode on Nokia N900.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch just uses the resource-managed extcon API when registering
the extcon notifier.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Use the quirk MUSB_PRESERVE_SESSION to preseve MUSB_DEVCTL during suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Add a quirk to not clear MUSB_DEVCTL and then preserve the session during
a suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement PM methods specifics for da8xx glue.
The only thing to do is to power off the phy.
As the registers are in retention during suspend,
there is no need to save them.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
musb_generic_disable() only has two lines of code. So remove it and let
the callers directly call those two lines.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DA8xx driver is registering and using the CPPI 3.0 DMA controller but
actually, the DA8xx has a CPPI 4.1 DMA controller.
Remove the CPPI 3.0 quirk and methods.
Fixes: f8e9f34f80a2 ("usb: musb: Fix up DMA related macros")
Fixes: 7f6283ed6fe8 ("usb: musb: Set up function pointers for DMA")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 2nd check for a non-zero return from copy_to_user is redundant as
it is has already been made a few lines earlier. This check was made
redundant because of previous fix to the copy_to_user error return
check.
Detected by CoverityScan, CID#114347 ("Logically Dead Code")
Fixes: 1865a9c382ede ("USB: adutux: fix misuse of return value of copy_to_user()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 2fc305be364e ("usb: chipidea: msm: Mux over secondary phy at the
right time")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
When the qcom chipidea controller is used with an extcon, we need
to signal device mode or host mode to the phy so it can configure
itself for the correct mode. This should be done after the phy is
powered up, so that the register writes work correctly. Add in
the appropriate phy_set_mode() call here.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
vram_size is supposed to be the total amount of VRAM that can be used by
userspace, which corresponds to the TTM VRAM manager size (which is
normally the full amount of VRAM, but can be just the visible VRAM when
DMA can't be used for BO migration for some reason).
The above was incorrectly used for vram_visible before, resulting in
generally too large values being reported.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Missing check for crtcs present.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=193341
https://bugs.freedesktop.org/show_bug.cgi?id=99387
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
clang complains about "__init" being attached to a struct name:
kernel/trace/trace_kprobe.c:1375:15: error: '__section__' attribute only applies to functions and global variables
The intention must have been to mark the function as __init instead of
the type, so move the attribute there.
Link: http://lkml.kernel.org/r/20170201165826.2625888-1-arnd@arndb.de
Fixes: f18f97ac43d7 ("tracing/kprobes: Add a helper method to return number of probe hits")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Some AArch64 UEFI implementations disable the MMU in ExitBootServices(),
after which unaligned accesses to RAM are no longer supported.
Commit:
abfb7b686a3e ("efi/libstub/arm*: Pass latest memory map to the kernel")
fixed an issue in the memory map handling of the stub FDT code, but
inadvertently created an issue with such firmware, by moving some
of the FDT manipulation to after the invocation of ExitBootServices().
Given that the stub's libfdt implementation uses the ordinary, accelerated
string functions, which rely on hardware handling of unaligned accesses,
manipulating the FDT with the MMU off may result in alignment faults.
So fix the situation by moving the update_fdt_memmap() call into the
callback function invoked by efi_exit_boot_services() right before it
calls the ExitBootServices() UEFI service (which is arguably a better
place for it anyway)
Note that disabling the MMU in ExitBootServices() is not compliant with
the UEFI spec, and carries great risk due to the fact that switching from
cached to uncached memory accesses halfway through compiler generated code
(i.e., involving a stack) can never be done in a way that is architecturally
safe.
Fixes: abfb7b686a3e ("efi/libstub/arm*: Pass latest memory map to the kernel")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Cc: <stable@vger.kernel.org>
Cc: mark.rutland@arm.com
Cc: linux-efi@vger.kernel.org
Cc: matt@codeblueprint.co.uk
Cc: leif.lindholm@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1485971102-23330-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
syszkaller fuzzer was able to trigger a divide by zero, when
TCP window scaling is not enabled.
SO_RCVBUF can be used not only to increase sk_rcvbuf, also
to decrease it below current receive buffers utilization.
If mss is negative or 0, just return a zero TCP window.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Casting is a high precedence operation but "off" and "i" are in terms of
bytes so we need to have some parenthesis here.
Fixes: fbfa743a9d2a ("ipv6: fix ip6_tnl_parse_tlv_enc_lim()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit cdba756f5803a2 ("net: move ndo_features_check() close to
ndo_start_xmit()") inadvertently moved the doc comment for
.ndo_fix_features instead of .ndo_features_check. Fix the comment
ordering.
Fixes: cdba756f5803a2 ("net: move ndo_features_check() close to ndo_start_xmit()")
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current version, the matchall internal state is split into two
structs: cls_matchall_head and cls_matchall_filter. This makes little
sense, as matchall instance supports only one filter, and there is no
situation where one exists and the other does not. In addition, that led
to some races when filter was deleted while packet was processed.
Unify that two structs into one, thus simplifying the process of matchall
creation and deletion. As a result, the new, delete and get callbacks have
a dummy implementation where all the work is done in destroy and change
callbacks, as was done in cls_cgroup.
Fixes: bf3994d2ed31 ("net/sched: introduce Match-all classifier")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d9c728949ddc ("vfio/spapr: Postpone default window creation")
added an additional exit to the VFIO_IOMMU_SPAPR_TCE_CREATE case and
made it possible to return from tce_iommu_ioctl() without unlocking
container->lock; this fixes the issue.
Fixes: d9c728949ddc ("vfio/spapr: Postpone default window creation")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Recent commit 34393529163a ("be2net: fix MAC addr setting on privileged
BE3 VFs") allows privileged BE3 VFs to set its MAC address during
initialization. Although the initial MAC for such VFs is already
programmed by parent PF the subsequent setting performed by VF is OK,
but in certain cases (after fresh boot) this command in VF can fail.
The MAC should be initialized only when:
1) no MAC is programmed (always except BE3 VFs during first init)
2) programmed MAC is different from requested (e.g. MAC is set when
interface is down). In this case the initial MAC programmed by PF
needs to be deleted.
The adapter->dev_mac contains MAC address currently programmed in HW so
it should be zeroed when the MAC is deleted from HW and should not be
filled when MAC is set when interface is down in be_mac_addr_set() as
no programming is performed in this case.
Example of failure without the fix (immediately after fresh boot):
# ip link set eth0 up <- eth0 is BE3 PF
be2net 0000:01:00.0 eth0: Link is Up
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create 1 VF
...
be2net 0000:01:04.0: Emulex OneConnect(be3): VF port 0
# ip link set eth8 up <- eth8 is created privileged VF
be2net 0000:01:04.0: opcode 59-1 failed:status 1-76
RTNETLINK answers: Input/output error
# echo 0 > /sys/class/net/eth0/device/sriov_numvfs <- Delete VF
iommu: Removing device 0000:01:04.0 from group 33
...
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create it again
iommu: Removing device 0000:01:04.0 from group 33
...
# ip link set eth8 up
be2net 0000:01:04.0 eth8: Link is Up
Initialization is now OK.
v2 - Corrected the comment and condition check suggested by Suresh & Harsha
Fixes: 34393529163a ("be2net: fix MAC addr setting on privileged BE3 VFs")
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Acked-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Chunfeng Yun
Gustavo A. R. Silva
Linus Torvalds
Michal Hocko
Toshi Kani
David Lin
Kirill A. Shutemov
Peter Zijlstra
Dan Streetman
Amit Shah
Halil Pasic
Michael S. Tsirkin
Ard Biesheuvel
Radim Krčmář
Wei Yongjun
Icenowy Zheng
Bhumika Goyal
Tony Lindgren
Jérémy Lefaure
Bin Liu
Pali Rohár
Chanwoo Choi
Alexandre Bailon
Colin Ian King
Stephen Boyd
Michel Dänzer
Alex Deucher
Arnd Bergmann
Eric Dumazet
Dan Carpenter
Dimitris Michailidis
Yotam Gigi
Alexey Kardashevskiy
Ivan Vecera