| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Introduce API functions to restart and cancel tty buffer work, rather
than manipulate buffer work directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_write_message() allows the caller to directly write to a specific
tty. Since the line discipline is bypassed for the direct write,
nothing prevents the tty from being torn down after the tty count is
checked.
Hold the tty lock for the duration of the direct write.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tiocspgrp() is the ioctl handler for TIOCSPGRP, which runs in
non-atomic context; use spin_lock/unlock_irq (since interrupt state
is on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The job_control() check in n_tty_read() has nearly identical purpose
and results as tty_check_change(). Both functions' purpose is to
determine if the current task's pgrp is the foreground pgrp for the tty,
and if not, to signal the current pgrp.
Introduce __tty_check_change() which takes the signal to send
and performs the shared operations for job control() and
tty_check_change().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The UART_DUMMY_DR_RX status bit is equal to (1 << 16), so a u16 is too small
to hold that value. The result is that UART_DUMMY_DR_RX is never passed
to uart_insert_char(). This means that we're always accepting characters,
even when CREAD (in termios) is not set.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 0fd972a7d91d (module: relocate module_init from init.h to
module.h) broke the build of ttyFDC driver due to that driver's (mis)use
of module_mips_cdmm_driver() without first including module.h, for
example:
In file included from ./arch/mips/include/asm/cdmm.h +11 :0,
from drivers/tty/mips_ejtag_fdc.c +34 :
include/linux/device.h +1295 :1: warning: data definition has no type or storage class
./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’
include/linux/device.h +1295 :1: error: type defaults to ‘int’ in declaration of ‘module_init’ [-Werror=implicit-int]
./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: warning: parameter names (without types) in function declaration
Instead of just adding the module.h include, switch to using the new
builtin_mips_cdmm_driver() helper macro and drop the remove callback,
since it isn't needed. If module support is added later, the code can
always be resurrected.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.2.x-
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Guillaume Gomez <guillaume1.gomez@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The platforms that have this UART, but that don't have
separate PCI device for the DMA Engine, need to create the
HSU DMA Engine device separately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are no platforms where it's not possible to calculate
the number of channels based on IO space length, and since
that is the only purpose for struct hsu_dma_platform_data,
removing it.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This allows UART drivers to register HSU DMA Engine without
being forced to use ifdefs.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HSU (High Speed UART) DMA engine, like the name suggests, is
an integrated DMA engine for UART and UART alone. Therefore,
making the UART drivers responsible of selecting it and
removing the user selectable option for it. The UARTs with
this DMA engine can always select HSU_DMA when
SERIAL_8250_DMA option is enabled.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent patch to create common helper functions for modem control
lines created empty helper functions in a header file, but accidentally
did not mark them as 'static inline', which causes build errors:
drivers/tty/serial/mxs-auart.o: In function `mctrl_gpio_enable_ms':
mxs-auart.c:(.text+0x171c): multiple definition of `mctrl_gpio_enable_ms'
drivers/tty/serial/clps711x.o:clps711x.c:(.text+0x768): first defined here
drivers/tty/serial/mxs-auart.o: In function `mctrl_gpio_disable_ms':
mxs-auart.c:(.text+0x1720): multiple definition of `mctrl_gpio_disable_ms'
drivers/tty/serial/clps711x.o:clps711x.c:(.text+0x76c): first defined here
This adds the missing annotation, so the functions do not get placed
in each object file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ce59e48fdbad ("serial: mctrl_gpio: implement interrupt handling")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel MID UART quirks require already quite a bit of code
in 8250_pci.c. On new Intel platforms where it is used, the
integrated DMA engine no longer has its own PCI device, but
is instead configured from the UART's MMIO. That means we
will have to add even more code for handling just MID UARTs.
Instead of adding that to 8250_pci.c, splitting the support
of Intel MID UART into its own driver. Handling of the
integrated DMA engine becomes much simpler this way. Own
driver will also remove the need for things like specific
set_termios hooks for every board using this UART, and
simplify the handling of it in general.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for DT and command line based earlycon support for
lpuart and lpuart32 used on Freescale Vybrid and and QorIQ LS1021A
processors.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We recently got rid of some modular code in this driver and also
got rid of the unused ".remove" function at the same time. Thierry
noted that it was however possible to force the remove through the
bind/unbind interface.
Since this is a console device used on 2005 vintage 74xx based
powerpc embedded targets, and is essentially always used in
conjunction with SERIAL_MPSC_CONSOLE=y -- there is no sane reason
anyone would ever want to unbind the builtin driver and lose the
console. So we just explicitly block bind/unbind operations and
prevent root from shooting themselves in the foot.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Waking the reader immediately upon receipt of TTY_BREAK or TTY_PARITY
chars has no effect on the outcome of read():
1. Only non-canonical/EXTPROC mode applies since canonical mode
will not return data until a line termination is received anyway
2. EXTPROC mode - the reader will always be woken by the input worker
3. Non-canonical modes
a. MIN == 0, TIME == 0
b. MIN == 0, TIME > 0
c. MIN > 0, TIME > 0
minimum_to_wake is always 1 in these modes so the reader will always
be woken by the input worker
d. MIN > 0, TIME == 0
although the reader will not be woken by the input worker unless the
minimum data is received, the reader would not otherwise have
returned the received data
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The statement after if should be indenteted. So fix this.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a misplaced bracket in atmel_init_rs485 which sets
rs485-rx-during-tx and rs485-enabled-at-boot-time only if
rs485-rts-delay is set in of.
This is clearly a bug, so fix it by moving the bracket to the proper
place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In-tree users of wait_event_interruptible_tty() have been removed;
remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tty lock is strictly for serializing tty lifetime events
(open/close/hangup), and not for line discipline serialization.
The tty core already provides serialization of concurrent writes
to the same tty, and line discipline lifetime management (by ldisc
references), so pinning the tty via tty_lock() is unnecessary and
counter-productive; remove tty lock use.
However, the line discipline is responsible for serializing reads
(if required by the line discipline); add read_lock mutex to
serialize calls of r3964_read().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tty core provides read_wait waitqueue specifically for line
disciplines to wait readers; otherwise, the line discipline may
miss wakeups generated by the tty core.
NB: The tty core already provides serialization for the line discipline's
close() method, and guarantees no readers or writers will be using the
closing instance of the line discipline. Completely remove that wakeup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the removal of tty_wait_until_sent_from_close(), tty drivers
no longer wait during open for parallel closes to complete (instead,
the tty core waits before calling the driver open() method). Thus,
the close_wait waitqueue is no longer used for waiting.
Remove struct tty_port::close_wait.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
close_wait is no longer needed or provided by the tty core.
Move close_wait to struct gs_port.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since at least before 2.6.30, tty drivers that do not drop the tty lock
while closing cannot observe ASYNC_CLOSING set while holding the
tty lock; this includes the tty driver's open() and hangup() methods,
since the tty core calls these methods holding the tty lock.
For these drivers, waiting for ASYNC_CLOSING to clear while opening
is not required, since this condition cannot occur. Similarly, even
when the open() method drops and reacquires the tty lock after
blocking, ASYNC_CLOSING cannot be set (again, for drivers that
do not drop the tty lock while closing).
Now that tty port drivers no longer drop the tty lock while closing
(since 'tty: Remove tty_wait_until_sent_from_close()'), the same
conditions apply: waiting for ASYNC_CLOSING to clear while opening
is not required, nor is re-checking ASYNC_CLOSING after dropping and
reacquiring the tty lock while blocking (eg., in *_block_til_ready()).
Note: The ASYNC_CLOSING flag state is still maintained since several
bitrotting drivers use it for (dubious) other purposes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_wait_until_sent_from_close() drops the tty lock while waiting
for the tty driver to finish sending previously accepted data (ie.,
data remaining in its write buffer and transmit fifo).
tty_wait_until_sent_from_close() was added by commit a57a7bf3fc7e
("TTY: define tty_wait_until_sent_from_close") to prevent the entire
tty subsystem from being unable to open new ttys while waiting for
one tty to close while output drained.
However, since commit 0911261d4cb6 ("tty: Don't take tty_mutex for tty
count changes"), holding a tty lock while closing does not prevent other
ttys from being opened/closed/hung up, but only prevents lifetime event
changes for the tty under lock.
Holding the tty lock while waiting for output to drain does prevent
parallel non-blocking opens (O_NONBLOCK) from advancing or returning
while the tty lock is held. However, all parallel opens _already_
block even if the tty lock is dropped while closing and the parallel
open advances. Blocking in open has been in mainline since at least 2.6.29
(see tty_port_block_til_ready(); note the test for O_NONBLOCK is _after_
the wait while ASYNC_CLOSING).
IOW, before this patch a non-blocking open will sleep anyway for the
_entire_ duration of a parallel hardware shutdown, and when it wakes, the
error return will cause a release of its tty, and it will restart with
a fresh attempt to open. Similarly with a blocking open that is already
waiting; when it's woken, the hardware shutdown has already completed
to ASYNC_INITIALIZED is not set, which forces a release and restart as
well.
So, holding the tty lock across the _entire_ close (which is what this
patch does), even while waiting for output to drain, is equivalent to
the current outcome wrt parallel opens.
Cc: Alan Cox <alan@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the tegra UART driver there are three places where the RX DMA buffer
is handled and pushed up to the tty layer. In all three instances the
same functions are called and so instead of duplicating the code in three
places, move this code to a new helper function and use this new function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The serial-tegra driver always uses DMA and hence the driver always
allocates DMA channels. Therefore, the test to see if the RX DMA channel
is initialised in tegra_uart_stop_rx() is unnecessary and so remove
the test and the code that corresponds to the case where the RX DMA
channel is not initialised. Please note that the call to
tegra_uart_stop_rx() should always be before the call to
tegra_uart_shutdown() which will uninitialise the RX DMA channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some functions in the serial-tegra driver have unnecessary return
statements at the end of a void function and so remove them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 853a699739fe ("serial: tegra: handle race condition on uart rx
side") attempted to fix a race condition between the RX end of
transmission interrupt and RX DMA completion callback. Despite this
fix there is still another case where these two paths can race and
result in duplicated data. The race condition is as follows:
1. DMA completion interrupt occurs and schedules tasklet to call DMA
callback.
2. DMA callback for the UART driver starts to execute. This will copy
the data from the DMA buffer and restart the DMA. This is done under
uart port spinlock.
3. During the callback, UART interrupt is raised for end of receive. The
UART ISR runs and waits to acquire port spinlock held by the DMA
callback.
4. DMA callback gives up spinlock after copying the data, but before
restarting DMA.
5. UART ISR acquires the spin lock and reads the same DMA buffer because
DMA has not been restarted yet.
The release of the spinlock during the DMA callback was introduced by
commit 9b88748b362c ("tty: serial: tegra: drop uart_port->lock before
calling tty_flip_buffer_push()") to fix a spinlock lock-up issue when
calling tty_flip_buffer_push(). However, since then commit a9c3f68f3cd8
("tty: Fix low_latency BUG") migrated tty_flip_buffer_push() to always
use a workqueue, allowing tty_flip_buffer_push() to be called from
within atomic sections. Therefore, we can remove the unlocking of the
spinlock from the DMA callback and UART ISR and this will ensure that
the race condition no longer occurs.
Reported-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clearing UART_MCR_RTS or UART_MCR_XONANY is unnecessary; these bits
are never set in the shadow mcr. The RTS clear is especially confusing.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The same serial hardware is present on LS2080A which is arm64, and
LS1021A which is arm32, so don't limit the workaround to PPC.
Unlike PPC which uses arch/powerpc/kernel/legacy_serial.c, the ARM
targets use drivers/tty/serial/of_serial.c, so add the handle_irq
override check there as well.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to hardcode the MEN_Z135_MEM_SIZE. The MCB subsystem
already knowns the size which is located in the chameleon table.
MCB parse the chameleon table to get the resources of each IP and provide
the mcb_request_mem function to get those resources.
Use mcb_request_mem to get the resources. This function also takes care of
the memory region naming allocated by the driver for each of the instances.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Turning on KVM and LPAE support on top of a multi_v7_defconfig will
produce a compiler warning in the Atmel serial driver:
drivers/tty/serial/atmel_serial.c: In function 'atmel_verify_port':
drivers/tty/serial/atmel_serial.c:2299:6: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
if ((void *)port->mapbase != ser->iomem_base)
^
Fix that by using the cast on the right hand side instead, as similar
code already does in other drivers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
My Intel email address will soon expire. Replace it with my
personal address so people still know where to send patches.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1444494136-10333-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Leandro Awa writes:
"After switching to version 4.1.6, our parallelized and distributed
workflows now fail consistently with errors of the form:
T34: ./regex.c:39:22: error: config.h: No such file or directory
From our 'git bisect' testing, the following commit appears to be the
possible cause of the behavior we've been seeing: commit 766c4cbfacd8"
Al Viro says:
"What happens is that 766c4cbfacd8 got the things subtly wrong.
We used to treat d_is_negative() after lookup_fast() as "fall with
ENOENT". That was wrong - checking ->d_flags outside of ->d_seq
protection is unreliable and failing with hard error on what should've
fallen back to non-RCU pathname resolution is a bug.
Unfortunately, we'd pulled the test too far up and ran afoul of
another kind of staleness. The dentry might have been absolutely
stable from the RCU point of view (and we might be on UP, etc), but
stale from the remote fs point of view. If ->d_revalidate() returns
"it's actually stale", dentry gets thrown away and the original code
wouldn't even have looked at its ->d_flags.
What we need is to check ->d_flags where 766c4cbfacd8 does (prior to
->d_seq validation) but only use the result in cases where we do not
discard this dentry outright"
Reported-by: Leandro Awa <lawa@nvidia.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=104911
Fixes: 766c4cbfacd8 ("namei: d_is_negative() should be checked...")
Tested-by: Leandro Awa <lawa@nvidia.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 76c44f6d80 introduced the possibly for "Overflow" to be reported
by the snapshot device's status. Older userspace (e.g. lvm2) does not
handle the "Overflow" status response.
Fix this incompatibility by requiring newer userspace code, that can
cope with "Overflow", request the persistent store with overflow support
by using "PO" (Persistent with Overflow) for the snapshot store type.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Fixes: 76c44f6d80 ("dm snapshot: don't invalidate on-disk image on snapshot write overflow")
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
As we're about to remove the of_node field from the irqdomain
structure, introduce an accessor for it. Subsequent patches
will take care of the actual repainting.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1444402211-1141-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
A recent cleanup removed the 'irq' parameter from many functions, but
left the documentation for this in place for at least one function.
This removes it.
Fixes: bd0b9ac405e1 ("genirq: Remove irq argument from irq flow handlers")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: kbuild-all@01.org
Cc: Austin Schuh <austin@peloton-tech.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/5400000.cD19rmgWjV@wuerfel
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
A cleanup of the omap gpio driver introduced a use of the
handle_bad_irq() function in a device driver that can be
a loadable module.
This broke the ARM allmodconfig build:
ERROR: "handle_bad_irq" [drivers/gpio/gpio-omap.ko] undefined!
This patch exports the handle_bad_irq symbol in order to
allow the use in modules.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Austin Schuh <austin@peloton-tech.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/5847725.4IBopItaOr@wuerfel
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The cleaner policy doesn't make use of the per cache block hint space in
the metadata (unlike the other policies). When switching from the
cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block)
was observed. The crash was caused by bugs in dm-cache-metadata.c
when trying to skip creation of the hint btree.
The minimal fix is to change hint size for the cleaner policy to 4 bytes
(only hint size supported).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
The commit 55ce74d4bfe1b9444436264c637f39a152d1e5ac (md/raid1: ensure
device failure recorded before write request returns) is causing crash in
the LVM2 testsuite test shell/lvchange-raid.sh. For me the crash is 100%
reproducible.
The reason for the crash is that the newly added code in raid1d moves the
list from conf->bio_end_io_list to tmp, then tests if tmp is non-empty and
then incorrectly pops the bio from conf->bio_end_io_list (which is empty
because the list was alrady moved).
Raid-10 has a similar bug.
Kernel Fault: Code=15 regs=000000006ccb8640 (Addr=0000000100000000)
CPU: 3 PID: 1930 Comm: mdX_raid1 Not tainted 4.2.0-rc5-bisect+ #35
task: 000000006cc1f258 ti: 000000006ccb8000 task.ti: 000000006ccb8000
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111111000001111 Not tainted
r00-03 000000ff0804fe0f 000000001059d000 000000001059f818 000000007f16be38
r04-07 000000001059d000 000000007f16be08 0000000000200200 0000000000000001
r08-11 000000006ccb8260 000000007b7934d0 0000000000000001 0000000000000000
r12-15 000000004056f320 0000000000000000 0000000000013dd0 0000000000000000
r16-19 00000000f0d00ae0 0000000000000000 0000000000000000 0000000000000001
r20-23 000000000800000f 0000000042200390 0000000000000000 0000000000000000
r24-27 0000000000000001 000000000800000f 000000007f16be08 000000001059d000
r28-31 0000000100000000 000000006ccb8560 000000006ccb8640 0000000000000000
sr00-03 0000000000249800 0000000000000000 0000000000000000 0000000000249800
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 000000001059f61c 000000001059f620
IIR: 0f8010c6 ISR: 0000000000000000 IOR: 0000000100000000
CPU: 3 CR30: 000000006ccb8000 CR31: 0000000000000000
ORIG_R28: 000000001059d000
IAOQ[0]: call_bio_endio+0x34/0x1a8 [raid1]
IAOQ[1]: call_bio_endio+0x38/0x1a8 [raid1]
RP(r2): raid_end_bio_io+0x88/0x168 [raid1]
Backtrace:
[<000000001059f818>] raid_end_bio_io+0x88/0x168 [raid1]
[<00000000105a4f64>] raid1d+0x144/0x1640 [raid1]
[<000000004017fd5c>] kthread+0x144/0x160
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 55ce74d4bfe1 ("md/raid1: ensure device failure recorded before write request returns.")
Fixes: 95af587e95aa ("md/raid10: ensure device failure recorded before write request returns.")
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
When scaling_available_frequencies is read on an offlined cpu, then
either lockup or junk values are displayed. This is caused by
freed freq_table, which policy is using.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When freqdomain_cpus attribute is read from an offlined cpu, it will
cause crash. This change prevents calling cpufreq_show_cpus when
policy driver_data is NULL.
Crash info:
[ 170.814949] BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
[ 170.814990] IP: [<ffffffff813b2490>] _find_next_bit.part.0+0x10/0x70
[ 170.815021] PGD 227d30067 PUD 229e56067 PMD 0
[ 170.815043] Oops: 0000 [#2] SMP
[ 170.816022] CPU: 3 PID: 3121 Comm: cat Tainted: G D OE 4.3.0-rc3+ #33
...
...
[ 170.816657] Call Trace:
[ 170.816672] [<ffffffff813b2505>] ? find_next_bit+0x15/0x20
[ 170.816696] [<ffffffff8160e47c>] cpufreq_show_cpus+0x5c/0xd0
[ 170.816722] [<ffffffffa031a409>] show_freqdomain_cpus+0x19/0x20 [acpi_cpufreq]
[ 170.816749] [<ffffffff8160e65b>] show+0x3b/0x60
[ 170.816769] [<ffffffff8129b31c>] sysfs_kf_seq_show+0xbc/0x130
[ 170.816793] [<ffffffff81299be3>] kernfs_seq_show+0x23/0x30
[ 170.816816] [<ffffffff81240f2c>] seq_read+0xec/0x390
[ 170.816837] [<ffffffff8129a64a>] kernfs_fop_read+0x10a/0x160
[ 170.816861] [<ffffffff8121d9b7>] __vfs_read+0x37/0x100
[ 170.816883] [<ffffffff813217c0>] ? security_file_permission+0xa0/0xc0
[ 170.816909] [<ffffffff8121e2e3>] vfs_read+0x83/0x130
[ 170.816930] [<ffffffff8121f035>] SyS_read+0x55/0xc0
...
...
[ 170.817185] ---[ end trace bc6eadf82b2b965a ]---
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.2+ <stable@vger.kernel.org> # 4.2+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Atmel sdhci device needs the
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk. Without it, the
internal clock could never stabilised when changing the sd clock
frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock
Control Register to 0 before computing the new value and writing it.
It disables the internal clock which causes a reset mecanism. If we
write the new value before this reset mecanism is done, it will prevent
the stabilisation of the internal clock, so a delay is needed. This
delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is
used.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case of armada_38x_quirks error, all clocks should be cleaned-up, same
as after mv_conf_mbus_windows failure.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to 'FE-2946959' erratum the clock inversion option is
needed to support slow frequencies when the card input hold time
requirement is high. This setting is not required for high speed
MMC and might cause timing violation.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
shci-pxav3 driver is enabling by default the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not
required for Armada 38x and leads to wrong clock setting in the divider.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
Peter Hurley
Timur Tabi
James Hogan
Guillaume Gomez
Heikki Krogerus
Arnd Bergmann
Stefan Agner
Paul Gortmaker
Geert Uytterhoeven
Jiri Slaby
Jon Hunter
Scott Wood
Andreas Werner
Andre Przywara
Linus Torvalds
Matt Fleming
Trond Myklebust
Mike Snitzer
Marc Zyngier
Joe Thornber
Mikulas Patocka
Srinivas Pandruvada
ludovic.desroches@atmel.com
Marcin Wojtas
Nadav Haklai