aboutsummaryrefslogtreecommitdiffstats
path: root/tools/perf/scripts/python/export-to-postgresql.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2016-04-20ARM: shmobile: timer: Drop support for Cortex A8Geert Uytterhoeven1-32/+20
Commit edf4100906044225 ("ARM: shmobile: sh7372 dtsi: Remove Legacy file") removed the DTS for the last shmobile SoC with a Cortex A8 CPU core (sh7372 aka SH-Mobile AP4), hence drop support for it in the loops-per-jiffy preset code. As "div" is always 1 for supported contemporary ARM processors, we can simplify the code: - Absorb shmobile_setup_delay_hz(), which was always called with mult = div = 1, - Return earlier if the Cortex A7/A15 arch timer exists and support is enabled. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2016-04-20ARM: shmobile: timer: Fix preset_lpj leading to too short delaysGeert Uytterhoeven1-17/+11
On all shmobile ARM SoCs, loop-based delays may complete early, which can be after only 1/3 (Cortex A9) or 1/2 (Cortex A7 or A15) of the minimum required time. This is caused by calculating preset_lpj based on incorrect assumptions about the number of clock cycles per loop: - All of Cortex A7, A9, and A15 run __loop_delay() at 1 loop per CPU clock cycle, - As of commit 11d4bb1bd067f9d0 ("ARM: 7907/1: lib: delay-loop: Add align directive to fix BogoMIPS calculation"), Cortex A8 runs __loop_delay() at 1 loop per 2 instead of 3 CPU clock cycles. On SoCs with Cortex A7 and/or A15 CPU cores, this went unnoticed, as delays use the ARM arch timer if available. R-Car Gen2 doesn't work if the arch timer is disabled. However, APE6 can be used without the arch timer. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2016-04-20Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"Sjoerd Simons1-13/+0
This reverts commit 19417bd9c511 ("ARM: dts: porter: Enable SCIF_CLK frequency and pins") as according to http://elinux.org/File:R-CarM2-KOELSCH_PORTER-B_PORTER_C_Comparison.pdf the external oscillator for SCIF_CLK is not mounted on the porter boards. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2016-04-20ARM: dts: r8a7791: Don't disable referenced optional clocksSjoerd Simons3-4/+3
clk_get on a disabled clock node will return EPROBE_DEFER, which can cause drivers to be deferred forever if such clocks are referenced in their clocks property. Update the various disabled external clock nodes to default to a frequency of 0, but don't disable them to prevent this. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2016-04-14ARM: davinci: clk: add set_parent callback for mux clocksDavid Lechner2-1/+19
Introduce a set_parent callback that will be used for mux clocks, such as the USB PHY muxes and the async3 clock domain mux. Signed-off-by: David Lechner <david@lechnology.com> [nsekhar@ti.com: checkpatch fixes] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2016-04-14ARM: davinci: da8xx: move usb code to new fileDavid Lechner3-75/+109
We will be adding more da8xx-specific code for phy and clocks, so it will be better to have this in a separate file. This way we don't have a bunch of #ifdefs for all of the da8xx stuff. While at it, fix some checkpatch warnings coming from existing code. Signed-off-by: David Lechner <david@lechnology.com> [nsekhar@ti.com: typo and checkpatch fixes] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2016-04-14ARM: davinci: use IRQCHIP_DECLARE for cp_intcDavid Lechner2-11/+3
Remove boilerplate code by using IRQCHIP_DECLARE macro. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2016-04-14ARM: davinci: remove unused DA8XX_NUM_UARTSDavid Lechner1-2/+0
DA8X_NUM_UARTS not used in the code anywhere and should be determined by DT anyway. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2016-04-14ARM: davinci: simplify call to of populateDavid Lechner1-3/+1
Take advantage of of_platoform_default_populate convience function. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2016-04-14ARM: DaVinci USB: removed deprecated properties from MUSB configPetr Kulhavy1-16/+0
The following properties of the musb_hdrc_config structure are deprecated and no longer required/used by the MUSB driver: .dyn_fifo .soft_con .dma .dma_channels .eps_bits Signed-off-by: Petr Kulhavy <petr@barix.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2016-04-10Linux 4.6-rc3Linus Torvalds1-1/+1
2016-04-10Revert "ext4: allow readdir()'s of large empty directories to be interrupted"Linus Torvalds2-10/+0
This reverts commit 1028b55bafb7611dda1d8fed2aeca16a436b7dff. It's broken: it makes ext4 return an error at an invalid point, causing the readdir wrappers to write the the position of the last successful directory entry into the position field, which means that the next readdir will now return that last successful entry _again_. You can only return fatal errors (that terminate the readdir directory walk) from within the filesystem readdir functions, the "normal" errors (that happen when the readdir buffer fills up, for example) happen in the iterorator where we know the position of the actual failing entry. I do have a very different patch that does the "signal_pending()" handling inside the iterator function where it is allowable, but while that one passes all the sanity checks, I screwed up something like four times while emailing it out, so I'm not going to commit it today. So my track record is not good enough, and the stars will have to align better before that one gets committed. And it would be good to get some review too, of course, since celestial alignments are always an iffy debugging model. IOW, let's just revert the commit that caused the problem for now. Reported-by: Greg Thelen <gthelen@google.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-04-09i2c: jz4780: really prevent potential division by zeroWolfram Sang1-1/+6
Make sure we avoid a division-by-zero OOPS in case clock-frequency is set too low in DT. Add missing '\n' while we are here. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Axel Lin <axel.lin@ingics.com>
2016-04-09Revert "i2c: jz4780: prevent potential division by zero"Wolfram Sang1-1/+1
This reverts commit 34cf2acdafaa31a13821e45de5ee896adcd307b1. 'ret' is not set when bailing out. Also, there is a better place to check for 0. Reported-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-04-08bridge, netem: mark mailing lists as moderatedstephen hemminger1-2/+2
I moderate these (lightly loaded) lists to block spam. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08parisc: Update comment regarding relative extable supportHelge Deller1-6/+4
Update the comment to reflect the changes of commit 0de7985 (parisc: Use generic extable search and sort routines). Signed-off-by: Helge Deller <deller@gmx.de>
2016-04-08parisc: Unbreak handling exceptions from kernel modulesHelge Deller4-0/+9
Handling exceptions from modules never worked on parisc. It was just masked by the fact that exceptions from modules don't happen during normal use. When a module triggers an exception in get_user() we need to load the main kernel dp value before accessing the exception_data structure, and afterwards restore the original dp value of the module on exit. Noticed-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org
2016-04-08parisc: Fix kernel crash with reversed copy_from_user()Helge Deller1-0/+3
The kernel module testcase (lib/test_user_copy.c) exhibited a kernel crash on parisc if the parameters for copy_from_user were reversed ("illegal reversed copy_to_user" testcase). Fix this potential crash by checking the fault handler if the faulting address is in the exception table. Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org Cc: Kees Cook <keescook@chromium.org>
2016-04-08parisc: Avoid function pointers for kernel exception routinesHelge Deller1-5/+5
We want to avoid the kernel module loader to create function pointers for the kernel fixup routines of get_user() and put_user(). Changing the external reference from function type to int type fixes this. This unbreaks exception handling for get_user() and put_user() when called from a kernel module. Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org
2016-04-08parisc: Handle R_PARISC_PCREL32 relocations in kernel modulesHelge Deller1-0/+8
Commit 0de7985 (parisc: Use generic extable search and sort routines) changed the exception tables to use 32bit relative offsets. This patch now adds support to the kernel module loader to handle such R_PARISC_PCREL32 relocations for 32- and 64-bit modules. Signed-off-by: Helge Deller <deller@gmx.de>
2016-04-08tuntap: restore default qdiscJason Wang1-2/+2
After commit f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev"), default qdisc was changed to noqueue because tuntap does not set tx_queue_len during .setup(). This patch restores default qdisc by setting tx_queue_len in tun_setup(). Fixes: f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev") Cc: Phil Sutter <phil@nwl.cc> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08orangefs: remove unused variableMartin Brandenburg1-3/+1
Signed-off-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com>
2016-04-08orangefs: Add KERN_<LEVEL> to gossip_<level> macrosJoe Perches1-14/+17
Emit the logging messages at the appropriate levels. Miscellanea: o Change format to fmt o Use the more common ##__VA_ARGS__ Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com>
2016-04-08orangefs: strncpy -> strscpyMartin Brandenburg1-1/+5
It would have been possible for a rogue client-core to send in a symlink target which is not NUL terminated. This returns EIO if the client-core gives us corrupt data. Leave debugfs and superblock code as is for now. Other dcache.c and namei.c strncpy instances are safe because ORANGEFS_NAME_MAX = NAME_MAX + 1; there is always enough space for a name plus a NUL byte. Signed-off-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com>
2016-04-08orangefs: clean up truncate ctime and mtime settingMartin Brandenburg1-15/+1
The ctime and mtime are always updated on a successful ftruncate and only updated on a successful truncate where the size changed. We handle the ``if the size changed'' bit. This matches FUSE's behavior. Signed-off-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com>
2016-04-08Orangefs: fix ifnullfree.cocci warningskbuild test robot1-2/+1
fs/orangefs/orangefs-debugfs.c:130:2-26: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values. NULL check before some freeing functions is not needed. Based on checkpatch warning "kfree(NULL) is safe this check is probably not required" and kfreeaddr.cocci by Julia Lawall. Generated by: scripts/coccinelle/free/ifnullfree.cocci Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com>
2016-04-08Orangefs: optimize boilerplate code.Mike Marshall2-2/+2
Suggested by David Binderman <dcb314@hotmail.com> The former can potentially be a performance win over the latter. memcpy(d, s, len); memset(d+len, c, size-len); memset(d, c, size); memcpy(d, s, len); Signed-off-by: Mike Marshall <hubcap@omnibond.com>
2016-04-08Orangefs: xattr.c cleanupMike Marshall1-16/+1
1. It is nonsense to test for negative size_t, suggested by David Binderman <dcb314@hotmail.com> 2. By the time Orangefs gets called, the vfs has ensured that name != NULL, and that buffer and size are sane. Signed-off-by: Mike Marshall <hubcap@omnibond.com>
2016-04-08mpls: find_outdev: check for err ptr in addition to NULL checkRoopa Prabhu1-0/+3
find_outdev calls inet{,6}_fib_lookup_dev() or dev_get_by_index() to find the output device. In case of an error, inet{,6}_fib_lookup_dev() returns error pointer and dev_get_by_index() returns NULL. But the function only checks for NULL and thus can end up calling dev_put on an ERR_PTR. This patch adds an additional check for err ptr after the NULL check. Before: Trying to add an mpls route with no oif from user, no available path to 10.1.1.8 and no default route: $ip -f mpls route add 100 as 200 via inet 10.1.1.8 [ 822.337195] BUG: unable to handle kernel NULL pointer dereference at 00000000000003a3 [ 822.340033] IP: [<ffffffff8148781e>] mpls_nh_assign_dev+0x10b/0x182 [ 822.340033] PGD 1db38067 PUD 1de9e067 PMD 0 [ 822.340033] Oops: 0000 [#1] SMP [ 822.340033] Modules linked in: [ 822.340033] CPU: 0 PID: 11148 Comm: ip Not tainted 4.5.0-rc7+ #54 [ 822.340033] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5.1-0-g8936dbb-20141113_115728-nilsson.home.kraxel.org 04/01/2014 [ 822.340033] task: ffff88001db82580 ti: ffff88001dad4000 task.ti: ffff88001dad4000 [ 822.340033] RIP: 0010:[<ffffffff8148781e>] [<ffffffff8148781e>] mpls_nh_assign_dev+0x10b/0x182 [ 822.340033] RSP: 0018:ffff88001dad7a88 EFLAGS: 00010282 [ 822.340033] RAX: ffffffffffffff9b RBX: ffffffffffffff9b RCX: 0000000000000002 [ 822.340033] RDX: 00000000ffffff9b RSI: 0000000000000008 RDI: 0000000000000000 [ 822.340033] RBP: ffff88001ddc9ea0 R08: ffff88001e9f1768 R09: 0000000000000000 [ 822.340033] R10: ffff88001d9c1100 R11: ffff88001e3c89f0 R12: ffffffff8187e0c0 [ 822.340033] R13: ffffffff8187e0c0 R14: ffff88001ddc9e80 R15: 0000000000000004 [ 822.340033] FS: 00007ff9ed798700(0000) GS:ffff88001fc00000(0000) knlGS:0000000000000000 [ 822.340033] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 822.340033] CR2: 00000000000003a3 CR3: 000000001de89000 CR4: 00000000000006f0 [ 822.340033] Stack: [ 822.340033] 0000000000000000 0000000100000000 0000000000000000 0000000000000000 [ 822.340033] 0000000000000000 0801010a00000000 0000000000000000 0000000000000000 [ 822.340033] 0000000000000004 ffffffff8148749b ffffffff8187e0c0 000000000000001c [ 822.340033] Call Trace: [ 822.340033] [<ffffffff8148749b>] ? mpls_rt_alloc+0x2b/0x3e [ 822.340033] [<ffffffff81488e66>] ? mpls_rtm_newroute+0x358/0x3e2 [ 822.340033] [<ffffffff810e7bbc>] ? get_page+0x5/0xa [ 822.340033] [<ffffffff813b7d94>] ? rtnetlink_rcv_msg+0x17e/0x191 [ 822.340033] [<ffffffff8111794e>] ? __kmalloc_track_caller+0x8c/0x9e [ 822.340033] [<ffffffff813c9393>] ? rht_key_hashfn.isra.20.constprop.57+0x14/0x1f [ 822.340033] [<ffffffff813b7c16>] ? __rtnl_unlock+0xc/0xc [ 822.340033] [<ffffffff813cb794>] ? netlink_rcv_skb+0x36/0x82 [ 822.340033] [<ffffffff813b4507>] ? rtnetlink_rcv+0x1f/0x28 [ 822.340033] [<ffffffff813cb2b1>] ? netlink_unicast+0x106/0x189 [ 822.340033] [<ffffffff813cb5b3>] ? netlink_sendmsg+0x27f/0x2c8 [ 822.340033] [<ffffffff81392ede>] ? sock_sendmsg_nosec+0x10/0x1b [ 822.340033] [<ffffffff81393df1>] ? ___sys_sendmsg+0x182/0x1e3 [ 822.340033] [<ffffffff810e4f35>] ? __alloc_pages_nodemask+0x11c/0x1e4 [ 822.340033] [<ffffffff8110619c>] ? PageAnon+0x5/0xd [ 822.340033] [<ffffffff811062fe>] ? __page_set_anon_rmap+0x45/0x52 [ 822.340033] [<ffffffff810e7bbc>] ? get_page+0x5/0xa [ 822.340033] [<ffffffff810e85ab>] ? __lru_cache_add+0x1a/0x3a [ 822.340033] [<ffffffff81087ea9>] ? current_kernel_time64+0x9/0x30 [ 822.340033] [<ffffffff813940c4>] ? __sys_sendmsg+0x3c/0x5a [ 822.340033] [<ffffffff8148f597>] ? entry_SYSCALL_64_fastpath+0x12/0x6a [ 822.340033] Code: 83 08 04 00 00 65 ff 00 48 8b 3c 24 e8 40 7c f2 ff eb 13 48 c7 c3 9f ff ff ff eb 0f 89 ce e8 f1 ae f1 ff 48 89 c3 48 85 db 74 15 <48> 8b 83 08 04 00 00 65 ff 08 48 81 fb 00 f0 ff ff 76 0d eb 07 [ 822.340033] RIP [<ffffffff8148781e>] mpls_nh_assign_dev+0x10b/0x182 [ 822.340033] RSP <ffff88001dad7a88> [ 822.340033] CR2: 00000000000003a3 [ 822.435363] ---[ end trace 98cc65e6f6b8bf11 ]--- After patch: $ip -f mpls route add 100 as 200 via inet 10.1.1.8 RTNETLINK answers: Network is unreachable Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08gpio: pca953x: Use correct u16 value for register word writeYong Li1-1/+2
The current implementation only uses the first byte in val, the second byte is always 0. Change it to use cpu_to_le16 to write the two bytes into the register Cc: stable@vger.kernel.org Signed-off-by: Yong Li <sdliyong@gmail.com> Reviewed-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-08gpiolib: Defer gpio device setup until after gpiolib initializationGuenter Roeck1-31/+67
Since commit ff2b13592299 ("gpio: make the gpiochip a real device"), attempts to add a gpio chip prior to gpiolib initialization cause the system to crash. This happens because gpio_bus_type has not been registered yet. Defer creating gpio devices until after gpiolib has been initialized to fix the problem. Cc: Greg Ungerer <gerg@uclinux.org> Cc: Alexandre Courbot <gnurou@gmail.com> Fixes: ff2b13592299 ("gpio: make the gpiochip a real device") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-08gpiolib: Do not use devm functions when registering gpio chipGuenter Roeck1-7/+12
It is possible that a gpio chip is registered before the gpiolib initialization code has run. This means we can not use devm_ functions to allocate memory at that time. Do it the old fashioned way. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-08gpio: pxa: fix legacy non pinctrl aware buildsRobert Jarzmik1-2/+2
In legacy pxa builds, ie. non device-tree and platform-data only builds, pinctrl is not yet available. As a consequence, the pinctrl gpio direction change function is a stub, returning always success. In the current state, the gpio driver direction function believes the pinctrl direction change was successful, and exits without actually changing the gpio direction. This patch changes the logic : - if the pinctrl direction function fails, gpio direction will report that failure - if the pinctrl direction function succeeds, gpio direction is changed by the gpio driver anyway. This is sub optimal in the pinctrl aware case, as the gpio direction will be changed twice: once by pinctrl function and another time by the gpio direction function. Yet it should be acceptable in this form, as this is functional for all pxa platforms (device-tree and platform-data), and moreover changing a gpio direction is very very seldom, usually in machine initialization, seldom in drivers probe, and an exception for ac97 reset bug. Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request") Reported-by: Guenter Roeck <guenter@roeck-us.net> Tested-by: Guenter Roeck <guenter@roeck-us.net> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-08gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*Dmitry Torokhov1-4/+12
When firmware does not use _DSD properties that allow properly name GPIO resources, the kernel falls back on parsing _CRS resources, and will return entries described as GpioInt() as general purpose GPIOs even though they are meant to be used simply as interrupt sources for the device: Device (ETSA) { Name (_HID, "ELAN0001") ... Method(_CRS, 0x0, NotSerialized) { Name(BUF0,ResourceTemplate () { I2CSerialBus( 0x10, /* SlaveAddress */ ControllerInitiated, /* SlaveMode */ 400000, /* ConnectionSpeed */ AddressingMode7Bit, /* AddressingMode */ "\\_SB.I2C1", /* ResourceSource */ ) GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone,, "\\_SB.GPSW") { BOARD_TOUCH_GPIO_INDEX } } ) Return (BUF0) } ... } This gives troubles with drivers such as Elan Touchscreen driver (elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and decide whether the driver is responsible for powering up and resetting the device, or firmware is. In the above case the lookup succeeds, we map GPIO as output and later fail to request client->irq interrupt that is mapped to the same GPIO. Let's ignore resources described as GpioInt() while parsing _CRS when requesting output GPIOs (but allow them when requesting GPIOD_ASIS or GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and then map it to interrupt with gpiod_to_irq). Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-07libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignmentDan Williams3-30/+51
When section alignment padding is in effect we need to shift / truncate the range that is queried for poison by the 'start_pad' or 'end_trunc' reservations. It's easiest if we just pass in an adjusted resource range rather than deriving it from the passed in namespace. With the resource range resolution pushed out to the caller we can also push the namespace-to-region lookup to the caller and drop the implicit pmem-type assumption about the passed in namespace object. Cc: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2016-04-07libnvdimm, pfn: fix uuid validationDan Williams1-1/+1
If we detect a namespace has a stale info block in the init path, we should overwrite with the latest configuration. In fact, we already return -ENODEV when the parent uuid is invalid, the same should be done for the 'self' uuid. Otherwise we can get into a condition where userspace is unable to reconfigure the pfn-device without directly / manually invalidating the info block. Cc: <stable@vger.kernel.org> Reported-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2016-04-07libnvdimm: fix smart data retrievalDan Williams1-1/+1
It appears that smart data retrieval has been broken the since the initial implementation. Fix the payload size to be 128-bytes per the specification. Cc: <stable@vger.kernel.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2016-04-07ipv6: Count in extension headers in skb->network_headerJakub Sitnicki1-4/+4
When sending a UDPv6 message longer than MTU, account for the length of fragmentable IPv6 extension headers in skb->network_header offset. Same as we do in alloc_new_skb path in __ip6_append_data(). This ensures that later on __ip6_make_skb() will make space in headroom for fragmentable extension headers: /* move skb->data to ip header from ext header */ if (skb->data < skb_network_header(skb)) __skb_pull(skb, skb_network_offset(skb)); Prevents a splat due to skb_under_panic: skbuff: skb_under_panic: text:ffffffff8143397b len:2126 put:14 \ head:ffff880005bacf50 data:ffff880005bacf4a tail:0x48 end:0xc0 dev:lo ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:104! invalid opcode: 0000 [#1] KASAN CPU: 0 PID: 160 Comm: reproducer Not tainted 4.6.0-rc2 #65 [...] Call Trace: [<ffffffff813eb7b9>] skb_push+0x79/0x80 [<ffffffff8143397b>] eth_header+0x2b/0x100 [<ffffffff8141e0d0>] neigh_resolve_output+0x210/0x310 [<ffffffff814eab77>] ip6_finish_output2+0x4a7/0x7c0 [<ffffffff814efe3a>] ip6_output+0x16a/0x280 [<ffffffff815440c1>] ip6_local_out+0xb1/0xf0 [<ffffffff814f1115>] ip6_send_skb+0x45/0xd0 [<ffffffff81518836>] udp_v6_send_skb+0x246/0x5d0 [<ffffffff8151985e>] udpv6_sendmsg+0xa6e/0x1090 [...] Reported-by: Ji Jianwen <jiji@redhat.com> Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-07Revert "ib_srpt: Convert to percpu_ida tag allocation"Bart Van Assche2-17/+40
This reverts commit 0fd10721fe3664f7549e74af9d28a509c9a68719. That patch causes the ib_srpt driver to crash as soon as the first SCSI command is received: kernel BUG at drivers/infiniband/ulp/srpt/ib_srpt.c:1439! invalid opcode: 0000 [#1] SMP Workqueue: target_completion target_complete_ok_work [target_core_mod] RIP: srpt_queue_response+0x437/0x4a0 [ib_srpt] Call Trace: srpt_queue_data_in+0x9/0x10 [ib_srpt] target_complete_ok_work+0x152/0x2b0 [target_core_mod] process_one_work+0x197/0x480 worker_thread+0x49/0x490 kthread+0xea/0x100 ret_from_fork+0x22/0x40 Aside from the crash, the shortcomings of that patch are as follows: - It makes the ib_srpt driver use I/O contexts allocated by transport_alloc_session_tags() but it does not initialize these I/O contexts properly. All the initializations performed by srpt_alloc_ioctx() are skipped. - It swaps the order of the send ioctx allocation and the transition to RTR mode which is wrong. - The amount of memory that is needed for I/O contexts is doubled. - srpt_rdma_ch.free_list is no longer used but is not removed. Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-04-07RDS: fix congestion map corruption for PAGE_SIZE > 4kshamir rabinovitch1-1/+1
When PAGE_SIZE > 4k single page can contain 2 RDS fragments. If 'rds_ib_cong_recv' ignore the RDS fragment offset in to the page it then read the data fragment as far congestion map update and lead to corruption of the RDS connection far congestion map. Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-07RDS: memory allocated must be align to 8shamir rabinovitch1-2/+2
Fix issue in 'rds_ib_cong_recv' when accessing unaligned memory allocated by 'rds_page_remainder_alloc' using uint64_t pointer. Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-07ARM: 8550/1: protect idiv patching against undefined gcc behaviorNicolas Pitre1-0/+2
It was reported that a kernel with CONFIG_ARM_PATCH_IDIV=y stopped booting when compiled with the upcoming gcc 6. Turns out that turning a function address into a writable array is undefined and gcc 6 decided it was OK to omit the store to the first word of the function while still preserving the store to the second word. Even though gcc 6 is now fixed to behave more coherently, it is a mystery that gcc 4 and gcc 5 actually produce wanted code in the kernel. And in fact the reduced test case to illustrate the issue does indeed break with gcc < 6 as well. In any case, let's guard the kernel against undefined compiler behavior by hiding the nature of the array location as suggested by gcc developers. Reference: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70128 Signed-off-by: Nicolas Pitre <nico@linaro.org> Reported-by: Marcin Juszkiewicz <mjuszkiewicz@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: stable@vger.kernel.org # v4.5 Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2016-04-07ARM: wire up preadv2 and pwritev2 syscallsRussell King3-2/+6
Wire up the preadv2 and pwritev2 syscalls for ARM. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2016-04-07GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOUAlexander Duyck5-4/+29
This patch fixes an issue I found in which we were dropping frames if we had enabled checksums on GRE headers that were encapsulated by either FOU or GUE. Without this patch I was barely able to get 1 Gb/s of throughput. With this patch applied I am now at least getting around 6 Gb/s. The issue is due to the fact that with FOU or GUE applied we do not provide a transport offset pointing to the GRE header, nor do we offload it in software as the GRE header is completely skipped by GSO and treated like a VXLAN or GENEVE type header. As such we need to prevent the stack from generating it and also prevent GRE from generating it via any interface we create. Fixes: c3483384ee511 ("gro: Allow tunnel stacking in the case of FOU/GUE") Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-07PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfsStrashko, Grygorii1-0/+2
Now wakeirq stops working for device if wakeup option for this device will be reconfigured through sysfs, like: echo disabled > /sys/devices/platform/extcon_usb1/power/wakeup echo enabled > /sys/devices/platform/extcon_usb1/power/wakeup Once above set of commands is executed the device's wakeup_source opject will be recreated and dev->power.wakeup->wakeirq field will contain NULL. As result, device_wakeup_arm_wake_irqs() will not arm wakeirq for the affected device. Hece, lets try to fix it in the following way: check for dev->wakeirq field when device_wakeup_attach() is called and if !NULL re-attach wakeirq to the device Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-07tools/power turbostat: work around RC6 counter wrapLen Brown1-4/+15
Sometimes the rc6 sysfs counter spontaneously resets, causing turbostat prints a very large number as it tries to calcuate % = 100 * (old - new) / interval When we see (old > new), print ***.**% instead of a bogus huge number. Note that this detection is not fool-proof, as the counter could reset several times and still result in new > old. Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-07tools/power turbostat: initial KBL supportLen Brown1-0/+14
KBL is similar to SKL Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-07tools/power turbostat: initial SKX supportLen Brown1-1/+8
SKX has a lot in common with HSX Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-07tools/power turbostat: decode BXT TSC frequency via CPUIDLen Brown1-1/+4
Hard-code BXT ART to 19200MHz, so turbostat --debug can fully enumerate TSC: CPUID(0x15): eax_crystal: 3 ebx_tsc: 186 ecx_crystal_hz: 0 TSC: 1190 MHz (19200000 Hz * 186 / 3 / 1000000) Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-07tools/power turbostat: initial BXT supportLen Brown1-0/+9
Broxton has a lot in common with SKL Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.