| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove variables and assignments that are never used.
Found by Krzysztof using cppcheck, e.g.:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/hotplug/ibmphp_res.c:1958 Variable 'bus_sec' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove variables and assignments that are never used.
Found by Krzysztof using cppcheck, e.g.:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/hotplug/cpqphp_core.c:1257 Variable 'rc' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
fu740_pcie_host_init() assigned "ret", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-fu740.c:227 Variable 'ret' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
hi3660_pcie_phy_init() assigned "pdev", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-kirin.c:336 Variable 'pdev' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove variables and assignments that are never used.
Found by Krzysztof using cppcheck, e.g.,
$ cppcheck --enable=all --force
uselessAssignmentPtrArg drivers/pci/proc.c:102 Assignment of function parameter has no effect outside the function. Did you forget dereferencing it?
unreadVariable drivers/pci/setup-bus.c:1528 Variable 'old_flags' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The struct pci_filp_private has no users outside drivers/pci/proc.c and is
only used when HAVE_PCI_MMAP is defined.
Wrap the struct pci_filp_private definition itself in #ifdef HAVE_PCI_MMAP.
Found by cppcheck:
$ cppcheck --enable=all --force drivers/pci/proc.c
drivers/pci/proc.c:192:6: style: struct member 'pci_filp_private::write_combine' is never used. [unusedStructMember]
Link: https://lore.kernel.org/r/20210706003145.3054881-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some ATI SB600 USB adapters advertise MSI, but if INTx is disabled by
setting PCI_COMMAND_INTX_DISABLE, MSI doesn't work either. The PCI/PCIe
specs do not require software to set PCI_COMMAND_INTX_DISABLE when enabling
MSI, but Linux has done that for many years.
Mick reported that 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI
devices") broke these devices. Prior to 306c54d0edb6, they used INTx.
Starting with 306c54d0edb6, they use MSI, and and the fact that Linux sets
PCI_COMMAND_INTX_DISABLE means both INTx and MSI are disabled on these
devices.
Avoid this SB600 defect by disabling MSI so we use INTx as before.
Fixes: 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")
Link: https://lore.kernel.org/r/20220321183446.1108325-1-helgaas@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215690
Link: https://lore.kernel.org/all/PxIByDyBRcsbpcmVhGSNDFAoUcMmb78ctXCkw6fbpx25TGlCHvA6SJjjFkNr1FfQZMntYPTNyvEnblxzAZ8a6jP9ddLpKeCN6Chi_2FuexU=@protonmail.com/
Link: https://lore.kernel.org/r/20220314101448.90074-1-andriy.shevchenko@linux.intel.com
BugLink: https://lore.kernel.org/all/20200702143045.23429-1-andriy.shevchenko@linux.intel.com/
Reported-by: Mick Lorain <micklorain@protonmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The fu740 PCIe core does not probe any devices on the SiFive Unmatched
board without this fix (or having U-Boot explicitly start the PCIe via
either boot-script or user command). The fix is to start the link at
2.5GT/s speeds and once the link is up then change the maximum speed back
to the default.
The U-Boot driver claims to set the link-speed to 2.5GT/s to get the probe
to work (and U-Boot does print link up at 2.5GT/s) in the following code:
https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/pci/pcie_dw_sifive.c?id=v2022.01#L271
Link: https://lore.kernel.org/r/20220318152430.526320-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The CLKREQ# signal is an open drain, active low signal that is driven
low by the remote Endpoint device. But it might not be driven low if no
Endpoint device is connected.
On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no
Endpoint is connected to assert CLKREQ#.
Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the
PHY can be initialized.
Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6e2 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
|
|
To balance phy->init_count, invoke the phy_exit() after phy_power_off().
Link: https://lore.kernel.org/r/1646289275-17813-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6e2 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
|
|
If a host that uses the IP's integrated MSI Receiver lost power
during suspend, we call dw_pcie_setup_rc() to reinit the RC. But
dw_pcie_setup_rc() always sets pp->irq_mask[ctrl] to ~0, so the mask
register is always set as 0xffffffff incorrectly, thus the MSI can't
work after resume.
Fix this issue by moving pp->irq_mask[ctrl] initialization to
dw_pcie_host_init() so we can correctly set the mask reg during both
boot and resume.
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211226074019.2556-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The calls to devm_gpiod_get_optional() have the -gpios at the end of the
name but the GPIO core code is already adding the suffix during the lookup.
This means the PCIe driver is not finding the necessary reset or power
lines to allow initialisation of the PCIe.
Drop the redundant '-gpios' when we look up GPIOs from the DT.
This bug has not been noticed because if U-Boot has setup the GPIO lines
for the hardware when it does the PCIe initialisation (either by booting
from PCIe or user command to access PCIe) then the PCIe will work in Linux.
The U-Boot as supplied by SiFive does not by default initialise any PCIe
component.
Link: https://lore.kernel.org/r/20220221210347.1335004-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Per Documentation/process/license-rules.rst, the SPDX MIT identifier is
equivalent to including the entire MIT license text from
LICENSES/preferred/MIT.
Replace the MIT license text with the equivalent SPDX identifier.
Link: https://lore.kernel.org/r/20220224224753.297579-12-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
In struct vga_device, io_lock_cnt and mem_lock_cnt are unsigned, but we
previously printed them with "%d", the signed decimal format. Print them
with the unsigned format "%u" instead.
Link: https://lore.kernel.org/r/20220224224753.297579-11-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Previously vga_arb_device_init() iterated through all VGA devices and
indicated whether legacy VGA routing to each could be controlled by an
upstream bridge.
But we determine that information in vga_arbiter_add_pci_device(), which we
call for every device, so we can log it there without iterating through the
VGA devices again.
Note that we call vga_arbiter_check_bridge_sharing() before adding the
device to vga_list, so we have to handle the very first device separately.
Link: https://lore.kernel.org/r/20220224224753.297579-10-helgaas@kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
vga_arb_device_card_gone() has always been empty. Remove it.
Link: https://lore.kernel.org/r/20220224224753.297579-9-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
a37c0f48950b ("vgaarb: Select a default VGA device even if there's no
legacy VGA") extended the vga_arb_device_init() subsys_initcall so that if
there are no other eligible devices, it could select a disabled VGA device
as the default.
Move this detection from vga_arb_select_default_device() to
vga_arbiter_add_pci_device() so every device, even those hot-added or
enumerated after vga_arb_device_init() is eligible for selection as the
default VGA device.
[bhelgaas: commit log, restructure]
Link: https://lore.kernel.org/r/20211015061512.2941859-5-chenhuacai@loongson.cn
Link: https://lore.kernel.org/r/20220224224753.297579-8-helgaas@kernel.org
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
|
|
a37c0f48950b ("vgaarb: Select a default VGA device even if there's no
legacy VGA") extended the vga_arb_device_init() subsys_initcall so it could
select a non-legacy VGA device as the default.
That failed to consider that PCI devices may be enumerated after
vga_arb_device_init(), e.g., hot-added devices or non-ACPI systems that do
PCI enumeration in pcibios_init(). Devices found then could never be
selected as the default.
One system where this is a problem is the MIPS-based Loongson where an
ASpeed AST2500 VGA device is behind a bridge that doesn't implement the VGA
Enable bit, so legacy resources are not routed to the VGA device. [1]
Fix this by moving the non-legacy VGA device selection from
vga_arb_select_default_device() to vga_arbiter_add_pci_device(), which is
called after every PCI device is enumerated, either by the
vga_arb_device_init() subsys_initcall or as an ADD_DEVICE notifier.
[1] https://lore.kernel.org/r/20210514080025.1828197-6-chenhuacai@loongson.cn
[bhelgaas: commit log, restructure]
Link: https://lore.kernel.org/r/20211015061512.2941859-5-chenhuacai@loongson.cn
Link: https://lore.kernel.org/r/20211015061512.2941859-7-chenhuacai@loongson.cn
Link: https://lore.kernel.org/r/20220224224753.297579-7-helgaas@kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
|
|
Previously we selected the firmware default device, i.e., one that owns the
boot framebuffer, as the default device in vga_arb_select_default_device().
This was only done in the vga_arb_device_init() subsys_initcall, so devices
enumerated later, e.g., by pcibios_init(), were not eligible.
Fix this by moving the firmware default device selection from
vga_arb_select_default_device() to vga_arbiter_add_pci_device(), which is
called after every PCI device is enumerated, either by the
vga_arb_device_init() subsys_initcall or as an ADD_DEVICE notifier.
Note that if vga_arb_select_default_device() previously found a device
owning the boot framebuffer, it unconditionally set it to be the default
VGA device, and no subsequent device could replace it.
[bhelgaas: commit log, restructure slightly]
Link: https://lore.kernel.org/r/20211015061512.2941859-7-chenhuacai@loongson.cn
Link: https://lore.kernel.org/r/20220224224753.297579-6-helgaas@kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
|
|
Default VGA device selection fails when PCI devices are enumerated after
the vga_arb_device_init() subsys_initcall.
vga_arbiter_add_pci_device() selects the first fully enabled device to
which legacy VGA resources are routed as the default VGA device. This is
an ADD_DEVICE notifier, so it runs after every PCI device is enumerated.
vga_arb_select_default_device() may select framebuffer devices, partially
enabled GPUs, or non-legacy devices that don't have legacy VGA resources
routed to them as the default VGA device. But this only happens once, from
the vga_arb_device_init() subsys_initcall, so it doesn't consider devices
enumerated after that:
acpi_init
acpi_scan_init
acpi_pci_root_init # PCI device enumeration (ACPI systems)
vga_arb_device_init
for_each_pci_device
vga_arbiter_add_pci_device # ADD_DEVICE notifier
if (VGA-owner)
vga_set_default_device <-- set default VGA
vga_arb_select_default_device # only called ONCE
for_each_vga_device
if (framebuffer)
vga_set_default_device <-- set default VGA to framebuffer
if (!vga_default_device())
if (non-legacy, integrated GPU, etc)
vga_set_default_device <-- set default VGA
if (!vga_default_device())
vga_set_default_device <-- set default VGA
pcibios_init
pcibios_scanbus # PCI device enumeration (non-ACPI systems)
...
vga_arbiter_add_pci_device # ADD_DEVICE notification
if (VGA-owner)
vga_set_default_device <-- set default VGA
Note that on non-ACPI systems, vga_arb_select_default_device() runs before
pcibios_init(), so it sees no VGA devices and can never set a framebuffer
device, a non-legacy integrated GPU, etc., as the default device.
Factor out the default VGA device selection to vga_is_boot_device(), called
from vga_arbiter_add_pci_device().
Then we can migrate the default device selection from
vga_arb_select_default_device() to the vga_arbiter_add_pci_device() path.
[bhelgaas: commit log, split to separate patch]
Link: https://lore.kernel.org/r/20211015061512.2941859-4-chenhuacai@loongson.cn
Link: https://lore.kernel.org/r/20220224224753.297579-5-helgaas@kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
On x86 and ia64, if a VGA device BARs include a framebuffer reported by
platform firmware, we select the device as the default VGA device. Factor
this code to a separate function. No functional change intended.
Link: https://lore.kernel.org/r/20220224224753.297579-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
|
|
Move vga_arb_integrated_gpu() earlier in file to prepare for future patch.
No functional change intended.
[bhelgaas: pull #ifdefs inside function]
Link: https://lore.kernel.org/r/20211015061512.2941859-3-chenhuacai@loongson.cn
Link: https://lore.kernel.org/r/20220224224753.297579-3-helgaas@kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The VGA arbiter is really PCI-specific and doesn't depend on any GPU
things. Move it to the PCI subsystem.
Note that misc_init() must be called before vga_arb_device_init(). These
are both subsys_initcalls, so this ordering depends on the link order,
which is determined by drivers/Makefile:
obj-y += pci/
obj-y += char/ <-- misc_init()
obj-y += gpu/ <-- vga_arb_device_init() (before this commit)
The drivers/pci/ subsys_initcalls are called *before* misc_init(), so
convert vga_arb_device_init() to subsys_initcall_sync(), which is called
after *all* subsys_initcalls.
Link: https://lore.kernel.org/r/20220224224753.297579-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Fix a misused goto label jump since that can result in a memory leak.
Link: https://lore.kernel.org/r/17e7b9b9ee6.c6d9c6a02564.4545388417402742326@zohomail.com
Signed-off-by: Li Chen <lchen@ambarella.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
i.MX6QP PCIe supports the reset logic, thus it can reset itself to the
initialized state when exit from L2 or L3 states.
Enable the i.MX6QP PCIe suspend/resume operations support.
Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
|
|
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb2659230120, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Fixes: fb2659230120 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes")
Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
|
|
Current kernel reports that BARs larger than 128GB, e.g., this 4TB BAR, are
disabled:
pci 0000:01:00.0: disabling BAR 4: [mem 0x00000000-0x3ffffffffff 64bit pref] (bad alignment 0x40000000000)
Increase the maximum BAR size from 128GB to 8TB for future expansion.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220118092117.10089-1-liudongdong3@huawei.com
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The link to the aer-inject referenced leads to an empty repo and seems no
longer used. Replace it with the link mentioned in
Documentation/PCI/pcieaer-howto.rst.
Link: https://lore.kernel.org/r/20220115104921.21606-1-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
On ARM64 Hyper-V guests, SPIs are used for the interrupts of virtual PCI
devices, and SPIs can be managed directly via GICD registers. Therefore
the retarget interrupt hypercall is not needed on ARM64.
An arch-specific interface hv_arch_irq_unmask() is introduced to handle
the architecture level differences on this. For x86, the behavior
remains unchanged, while for ARM64 no hypercall is invoked when
unmasking an irq for virtual PCI devices.
Link: https://lore.kernel.org/r/20220217034525.1687678-1-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
|
|
In order to do P2P communication the bridge ID of the platform must be in
the P2P device table.
Update the P2P device table with a device ID for the 3rd Gen Intel Xeon
Scalable Processors.
Link: https://lore.kernel.org/r/20220209162801.7647-1-michael.j.ruhl@intel.com
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
|
|
Today drivers/pci/controller/pci-xgene.c defines SZ_1T
Move it into linux/sizes.h so that it can be re-used elsewhere.
Link: https://lore.kernel.org/r/575cb7164cf124c75df7cb9242ea7374733942bf.1642752946.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: linux-pci@vger.kernel.org
|
|
Register 0x43c in its low 24 bits contains PCI class code.
Update code to set all 24 bits of PCI class code and not only upper 16 bits
of PCI class code.
Use a new macro PCI_CLASS_BRIDGE_PCI_NORMAL which represents whole 24 bits
of normal PCI bridge class.
Link: https://lore.kernel.org/r/20220214114109.26809-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roman Bacik <roman.bacik@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
|
|
Add these PCI class codes to pci_ids.h:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.
[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Qualcomm PCI bridge device (Device ID 0x0110) found in chipsets such as
SM8450 does not set the Command Completed bit unless writes to the Slot
Command register change "Control" bits.
This results in timeouts like below:
pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
Add the device to the Command Completed quirk to mark commands "completed"
immediately unless they change the "Control" bits.
Link: https://lore.kernel.org/r/20220210145003.135907-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The copy test uses the memcpy() to copy data between IO memory spaces.
This can trigger an alignment fault error (pasted the error logs below)
because memcpy() may use unaligned accesses on a mapped memory that is
just IO, which does not support unaligned memory accesses.
Fix it by using the correct memcpy API to copy from/to IO memory.
Alignment fault error logs:
Unable to handle kernel paging request at virtual address ffff8000101cd3c1
Mem abort info:
ESR = 0x96000021
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x21: alignment fault
Data abort info:
ISV = 0, ISS = 0x00000021
CM = 0, WnR = 0
swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000081773000
[ffff8000101cd3c1] pgd=1000000082410003, p4d=1000000082410003, pud=1000000082411003, pmd=1000000082412003, pte=0068004000001f13
Internal error: Oops: 96000021 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/0:0H Not tainted 5.15.0-rc1-next-20210914-dirty #2
Hardware name: LS1012A RDB Board (DT)
Workqueue: kpcitest pci_epf_test_cmd_handler
pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __memcpy+0x168/0x230
lr : pci_epf_test_cmd_handler+0x6f0/0xa68
sp : ffff80001003bce0
x29: ffff80001003bce0 x28: ffff800010135000 x27: ffff8000101e5000
x26: ffff8000101cd000 x25: ffff6cda941cf6c8 x24: 0000000000000000
x23: ffff6cda863f2000 x22: ffff6cda9096c800 x21: ffff800010135000
x20: ffff6cda941cf680 x19: ffffaf39fd999000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: ffffaf39fd2b6000
x14: 0000000000000000 x13: 15f5c8fa2f984d57 x12: 604d132b60275454
x11: 065cee5e5fb428b6 x10: aae662eb17d0cf3e x9 : 1d97c9a1b4ddef37
x8 : 7541b65edebf928c x7 : e71937c4fc595de0 x6 : b8a0e09562430d1c
x5 : ffff8000101e5401 x4 : ffff8000101cd401 x3 : ffff8000101e5380
x2 : fffffffffffffff1 x1 : ffff8000101cd3c0 x0 : ffff8000101e5000
Call trace:
__memcpy+0x168/0x230
process_one_work+0x1ec/0x370
worker_thread+0x44/0x478
kthread+0x154/0x160
ret_from_fork+0x10/0x20
Code: a984346c a9c4342c f1010042 54fffee8 (a97c3c8e)
---[ end trace 568c28c7b6336335 ]---
Link: https://lore.kernel.org/r/20211217094708.28678-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Update the comment about what happens when link goes down after we have
checked for link-up. If a PIO request is done while link-down, we have
a serious problem.
Link: https://lore.kernel.org/r/20220110015018.26359-23-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
This function is now always used in driver remove method, drop the
__maybe_unused attribute.
Link: https://lore.kernel.org/r/20220110015018.26359-22-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
By default, all Legacy INTx interrupts are masked, so there is no need to
mask this interrupt during irq_map() callback.
Link: https://lore.kernel.org/r/20220110015018.26359-21-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Callback for irq_mask_ack() is the same as for irq_mask(). As there is no
special handling for irq_ack(), there is no need to define irq_mask_ack()
too.
Link: https://lore.kernel.org/r/20220110015018.26359-20-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
|
|
Emulated root bridge currently provides only one Legacy INTA interrupt
which is used for reporting PCIe PME and ERR events and handled by kernel
PCIe PME and AER drivers.
Aardvark HW reports these PME and ERR events separately, so there is no
need to mix real INTA interrupt and emulated INTA interrupt for PCIe PME
and AER drivers.
Register a new advk-RP (as in Root Port) irq chip and a new irq domain
for emulated root bridge and use this new separate irq domain for
providing INTA interrupt from emulated root bridge for PME and ERR events.
The real INTA interrupt from real devices is now separate.
A custom map_irq callback function on PCI host bridge structure is used to
allocate IRQ mapping for emulated root bridge from new irq domain. Original
callback of_irq_parse_and_map_pci() is used for all other devices as before.
Link: https://lore.kernel.org/r/20220110015018.26359-19-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Enable aardvark PME interrupt unconditionally by unmasking it and read PME
requester ID to emulated bridge config space immediately after receiving
interrupt.
PME requester ID is stored in the PCIE_MSG_LOG_REG register, which contains
the last inbound message. So when new inbound message is received by HW
(including non-PM), the content in PCIE_MSG_LOG_REG register is replaced by
a new value.
PCIe specification mandates that subsequent PMEs are kept pending until the
PME Status Register bit is cleared by software by writing a 1b.
Support for masking/unmasking PME interrupt on emulated bridge via
PCI_EXP_RTCTL_PMEIE bit is now implemented only in emulated bridge config
space, to ensure that we do not miss any aardvark PME interrupt.
Reading of PCI_EXP_RTCAP and PCI_EXP_RTSTA registers is simplified as final
value is now always stored into emulated bridge config space by the
interrupt handler, so there is no need to implement support for these
registers in read_pcie callback.
Clearing of W1C bit PCI_EXP_RTSTA_PME is now also simplified as it is done
by pci-bridge-emul.c code for emulated bridge config space. So there is no
need to implement support for clearing this bit in write_pcie callback.
Link: https://lore.kernel.org/r/20220110015018.26359-18-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Currently enabling PCI_EXP_RTSTA_PME bit in PCI_EXP_RTCTL register does
nothing. This is because PCIe PME driver expects to receive PCIe interrupt
defined in PCI_EXP_FLAGS_IRQ register, but aardvark hardware does not
trigger PCIe INTx/MSI interrupt for PME event, rather it triggers custom
aardvark interrupt which this driver is not processing yet.
Fix this issue by handling PME interrupt in advk_pcie_handle_int() and
chaining it to PCIe interrupt 0 with generic_handle_domain_irq() (since
aardvark sets PCI_EXP_FLAGS_IRQ to zero). With this change PCIe PME driver
finally starts receiving PME interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-17-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
To optimize advk_pci_bridge_emul_pcie_conf_write() code, touch
PCIE_ISR0_REG and PCIE_ISR0_MASK_REG registers only when it is really
needed, when processing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME bits.
Link: https://lore.kernel.org/r/20220110015018.26359-16-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
Link: https://lore.kernel.org/r/20220110015018.26359-15-kabel@kernel.org
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
ERR interrupt is triggered when corresponding bit is unmasked in both ISR0
and PCI_EXP_DEVCTL registers. Unmasking ERR bits in PCI_EXP_DEVCTL register
is not enough. This means that currently the ERR interrupt is never
triggered.
Unmask ERR bits in ISR0 register at driver probe time. ERR interrupt is not
triggered until ERR bits are unmasked also in PCI_EXP_DEVCTL register,
which is done by AER driver. So it is safe to unconditionally unmask all
ERR bits in aardvark probe.
Aardvark HW sets PCI_ERR_ROOT_AER_IRQ to zero and when corresponding bits
in ISR0 and PCI_EXP_DEVCTL are enabled, the HW triggers a generic interrupt
on GIC. Chain this interrupt to PCIe interrupt 0 with
generic_handle_domain_irq() to allow processing of ERR interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-14-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
According to PCI 3.0 specification, sending both MSI and MSI-X interrupts
is done by DWORD memory write operation to doorbell message address. The
write operation for MSI has zero upper 16 bits and the MSI interrupt number
in the lower 16 bits, while the write operation for MSI-X contains a 32-bit
value from MSI-X table.
Since the driver only uses interrupt numbers from range 0..31, the upper
16 bits of the DWORD memory write operation to doorbell message address
are zero even for MSI-X interrupts. Thus we can enable MSI-X interrupts.
Testing proves that kernel can correctly receive MSI-X interrupts from PCIe
cards which supports both MSI and MSI-X interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-13-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
MSI address for receiving MSI interrupts needs to be correctly set before
enabling processing of MSI interrupts.
Move code for setting PCIE_MSI_ADDR_LOW_REG and PCIE_MSI_ADDR_HIGH_REG
from advk_pcie_init_msi_irq_domain() to advk_pcie_setup_hw(), before
enabling PCIE_CORE_CTRL2_MSI_ENABLE.
After this we can remove the now unused member msi_msg, which was used
only for MSI doorbell address. MSI address can be any address which cannot
be used to DMA to. So change it to the address of the main struct advk_pcie.
Link: https://lore.kernel.org/r/20220110015018.26359-12-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # f21a8b1b6837 ("PCI: aardvark: Move to MSI handling using generic MSI support")
|
|
We should not unmask MSIs at setup, but only when kernel asks for them
to be unmasked.
At setup, mask all MSIs, and implement IRQ chip callbacks for masking
and unmasking particular MSIs.
Link: https://lore.kernel.org/r/20220110015018.26359-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Refactor the masking of ISR0/1 Sources and unmasking of summary MSI interrupt
so that it corresponds to the comments:
- first mask all ISR0/1
- then unmask all MSIs
- then unmask summary MSI interrupt
Link: https://lore.kernel.org/r/20220110015018.26359-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Use simple
dev_fwnode(dev)
instead of
struct device_node *node = dev->of_node;
of_node_to_fwnode(node)
especially since the node variable is not used elsewhere in the function.
Link: https://lore.kernel.org/r/20220110015018.26359-9-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
Bjorn Helgaas
Krzysztof Wilczyński
Ben Dooks
Richard Zhu
Jisheng Zhang
Huacai Chen
Li Chen
Mark Tomlinson
Dongdong Liu
Yicong Yang
Boqun Feng
Michael J. Ruhl
Christophe Leroy
Pali Rohár
Manivannan Sadhasivam
Hou Zhiqiang
Marek Behún