| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The SATA node is wired to the third PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The PCIe node is wired to the second PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Describe the A3700 COMPHY node. It has three PHYs that can be
configured as follow:
* PCIe or GbE
* USB3 or GbE
* SATA or USB3
Each of them has its own memory area.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
By using the new binding for the partitions for the flashes we don't need
anymore to use #size-cells and #address-cells at the flash node level.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The mv88e6341 ethernet switch needs the cpu port control register to be
set with TX and RX internal delay in order to work.
This fixes ethernet support on system booted via a bootloader that
has not already configured this register (e.g. mainline u-boot, or
vendor u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
In order to be able to communicate with the 88e6341 switch some pins
have to be repurposed as RGMII and SMI pins.
This fixes ethernet support on system booted via a bootloader that
has not already configured those pins (e.g. mainline u-boot, or vendor
u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds initial support for micro-DPU (uDPU) board which is based on
Armada-3720 SoC. micro-DPU is the single-port FTTdp distribution point
unit made by Methode Electronics which offers complete modularity with
replaceable SFP modules both for uplink and downlink (G.hn over
twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds missing bindings for MT7623 sysirq.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This patch enables PCIEC0 PCI express controller on the sub board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Silicon Linux CAT 874 board has 2GB DDR memory. Update the dma-ranges
mapping for pciec0 node. Also declare pcie bus clock, since it is
generated on the CAT874 main board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds TMU{0|1|2|3|4} device nodes for r8a774c0 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds CMT{0|1|2|3} device nodes for r8a774c0 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch defines OOP tables for all CPUs, similarly to
what done by Takeshi Kihara and Yoshihiro Kaneko for the
R8A77990.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch define OOP tables for all CPUs.
This allows CPUFreq to function.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Successfully tested on H3 ES2.0 and M3-N ES1.0.
Transfer rates where >160MB/s for H3 and >200MB/s for M3-N.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add LVDS encoder node to r8a7744 SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add du node to r8a7744 SoC DT. Boards that want to enable the DU
need to specify the output topology.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update I2C Device node compatible string to be appropriate.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Update I2C device node compatible string to be appropriate.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Change the SDMMC clock source to support a maximum frequency of 200 MHz
on Tegra194.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add CQE Support for Tegra186 and Tegra194 SDMMC4 controller
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add SDMMC initial pad offsets used by auto calibration process.
Add SDMMC fixed drive strengths for Tegra210, Tegra186 and
Tegra194 which are used when calibration timeouts.
Fixed drive strengths are based on Pre SI Analysis of the pads.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra Combined UART is the proper primary serial port on P2888,
so use it.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add nodes required for communication through the Tegra Combined UART.
This includes the AON HSP instance, addition of shared interrupts
for the TOP0 HSP instance, and finally the TCU node itself. Also
mark the HSP instances as compatible to tegra194-hsp, as the hardware
is not identical but is compatible to tegra186-hsp.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable DFLL clock for Smaug board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add CPU power rail regulator for Smaug board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable DFLL clock for Jetson TX1 platform.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add pinmux for PWM-based DFLL support.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add CPU clocks for Tegra210.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add essential DFLL clock properties for Tegra210.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Update binding document for MT7622 BPI-R64 and MT7629 reference board.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
As we fallback to use "mediatek,mt7623" for MT7623a, remove unused
root node property "mediatek,mt7623a" in the document.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
On the Bananapi M3 and Cubietruck Plus, the DC input jacks are wired to
the ACIN pins, which is represented by the AC power supply. Both boards
have connectors for LiPo batteries, which are represented by the battery
power supply.
The H8 Homlet is a set-top box design. The DC input jack is wired to the
ACIN pins, but there are no battery connectors.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubieboard4 has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 Optimus has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The GMAC (gigabit ethernet controller) supports RGMII to connect to
the ethernet PHY, for gigabit network speeds.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 has the same GMAC found on the A31 SoC.
Add a device node, and an alias for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 has the same DWMAC hardware as on earlier Allwinner SoCs. The
accompanying GMAC clock register has been moved into the "System
Control" area.
Add a clock node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 Optimus has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The DC1SW output from the AXP809 is unused. Unused regulators should
still be listed so as to be considered to be fully constrained.
Fixes: aa4a27bc819e ("ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds dt-binding documentation of cpu for Mediatek MT8183.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The cpu_lp clock property is only needed when the CPUfreq driver
supports CPU cluster switching. But it was not a design for this driver
and it didn't handle that as well. So removing this property.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra124 cpufreq driver works only with DFLL clock, which is a
hardware-based frequency/voltage controller. The driver doesn't need to
control the regulator itself. Hence remove that.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add Tegra210 support for DFLL clock.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add new properties to configure the DFLL PWM regulator support.
Cc: devicetree@vger.kernel.org
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Libre Computer ALL-H3-CC H5 is one of the few boards that can have
its eMMC run at HS-DDR speed mode. Mark it as such.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On these A64 devices, the DC input jacks are wired to the ACIN pins of
the PMIC, which is represented by the AC power supply. With the
exception of the Nanopi A64, all devices include LiPo batteries or have
connectors for them, which are represented by the battery power supply.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Ensure the PCIe endpoint card reset that is toggled by the PCIe
controller itself is muxed correctly on the EspressoBin.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
Miquel Raynal
Gregory CLEMENT
Remi Pommarel
Vladimir Vid
Ryder Lee
Biju Das
Fabrizio Castro
Takeshi Kihara
Niklas Söderlund
Sowjanya Komatineni
Mikko Perttunen
Joseph Lo
Chen-Yu Tsai
Erin Lo
Peter De Schrijver
Rafał Miłecki