| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When we added CALIPSO support in Linux v4.8 we forgot to add it to the
list of supported protocols with display at boot.
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in single IRQ mode, the additional IRQ routines were being
skipped because only the XGMAC interrupt status was being checked.
Update the code so that the additional IRQ routines are checked whenever
an interrupt is received.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data, thus CSMR isn't cleared...
Fixes: 73a0d907301e ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the SH77{34|63} manuals are freely available, I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.
Fixes: 380af9e390ec ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"")
Fixes: f5d12767c8fd ("sh_eth: get SH77{34|63} support out of #ifdef")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From the realtek data sheet, the PID0 should be bit 0.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A single netlink socket might own multiple interfaces *and* a
scheduled scan request (which might belong to another interface),
so when it goes away both may need to be destroyed.
Remove the schedule_scan_stop indirection to fix this - it's only
needed for interface destruction because of the way this works
right now, with a single work taking care of all interfaces.
Cc: stable@vger.kernel.org
Fixes: 93a1e86ce10e4 ("nl80211: Stop scheduled scan if netlink client disappears")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits 0-15 usually used for that are occupied by the packet checksum).
Thus we need to set the 'shift_rd0' field in the SH7734 SoC data...
Fixes: f0e81fecd4f8 ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we failed to set up RSS on EF10 (e.g. because firmware declared
RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report
no fields, rather than confusingly reporting what fields we _would_ be
hashing on if RSS was working.
Fixes: dcb4123cbec0 ("sfc: disable RSS when unsupported")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QBMan CGR options needs to be zeroed before calling the init
function
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.
For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.
Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a minor fallout from the merge of the timers and the networking
trees. The following error may result if the PTP_1588_CLOCK
prerequisites are not available:
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0a5): undefined reference to `pps_unregister_source'
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0cc): undefined reference to `posix_clock_unregister'
drivers/built-in.o: In function `ptp_clock_event':
(.text+0x40e249): undefined reference to `pps_event'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e5e1): undefined reference to `pps_register_source'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e62c): undefined reference to `posix_clock_register'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e68d): undefined reference to `pps_unregister_source'
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_route_output() never returns NULL so
check dst->error instead of !dst.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here, If devm_ioremap will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
I would like to help with fbdev maintenance. I can dedicate some time
for reviewing and handling patches but won't have time for much more.
The subsystem will remain in maintenance mode (no new drivers will be
added to it).
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
max_retries _show and _store functions should test against cfg->max_retries,
not cfg->retry_timeout
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
I am taking over as XFS maintainer from Dave Chinner[1], so update
contact information and git tree pointers.
[1] http://lkml.iu.edu/hypermail/linux/kernel/1612.1/04390.html
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
There is a race window between write_cache_pages calling
clear_page_dirty_for_io and XFS calling set_page_writeback, in which
the mapping for an inode is tagged neither as dirty, nor as writeback.
If the COW shrinker hits in exactly that window we'll remove the delayed
COW extents and writepages trying to write it back, which in release
kernels will manifest as corruption of the bmap btree, and in debug
kernels will trip the ASSERT about now calling xfs_bmapi_write with the
COWFORK flag for holes. A complex customer load manages to hit this
window fairly reliably, probably by always having COW writeback in flight
while the cow shrinker runs.
This patch adds another check for having the I_DIRTY_PAGES flag set,
which is still set during this race window. While this fixes the problem
I'm still not overly happy about the way the COW shrinker works as it
still seems a bit fragile.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
We need to use the actual AG length when making per-AG reservations,
since we could otherwise end up reserving more blocks out of the last
AG than there are actual blocks.
Complained-about-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Dan Carpenter reported a double-free of rcur if _defer_finish fails
while we're recovering CUI items. Fix the error recovery to prevent
this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
The move from rx-handler to L3 receive handler inadvertantly dropped the
rx counters. Restore them.
Fixes: 74b20582ac38 ("net: l3mdev: Add hook in ip and ipv6")
Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
/sys/block/<dev>/queue/io_poll is a boolean. Fix the docs.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This updates gcc-common.h from Emese Revfy for gcc 7. This fixes issues seen
by Kugan and Arnd. Build tested with gcc 5.4 and 7 snapshot.
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This fixes build errors seen on gcc-4.9.3 or gcc-5.3.1 for an ARM:
arm-soc/init/initramfs.c: In function 'error':
arm-soc/init/initramfs.c:50:1: error: unrecognizable insn:
}
^
(insn 26 25 27 5 (set (reg:SI 111 [ local_entropy.243 ])
(rotatert:SI (reg:SI 116 [ local_entropy.243 ])
(const_int -30 [0xffffffffffffffe2]))) -1
(nil))
Patch from PaX Team <pageexec@freemail.hu>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Brad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Final nlmsg_len field update must reflect inserted net_dm_drop_point
data.
This patch depends on previous patch:
"drop_monitor: add missing call to genlmsg_end"
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dceed ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of custom rules being present we need to handle the case of the
LOCAL table being intialized after the new rule has been added. To address
that I am adding a new check so that we can make certain we don't use an
alias of MAIN for LOCAL when allocating a new table.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Oliver Brunel <jjk@jjacky.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changed function calls of resource allocation to new API. Changed way
of setting DMA mask. Removed unnecessary sanity check.
This patch is sent in regard to recently applied patch
Commit 83a77e9ec4150ee4acc635638f7dedd9da523a26
net: macb: Added PCI wrapper for Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have an exit callback in place, add init as well and get rid
of the custom PM callbacks in favour of the generic ones.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by calling the new glue
helper function.
For driver unbind, use the generic stmmac-platform remove implementation
and add an exit callback to disable the clock.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the syscon lookup-by-phandle helper so that the reference taken by
of_parse_phandle() is released when done with the node.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s/utliziation/utilization
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
5.2. Action on Reception of a Query
When a system receives a Query, it does not respond immediately.
Instead, it delays its response by a random amount of time, bounded
by the Max Resp Time value derived from the Max Resp Code in the
received Query message. A system may receive a variety of Queries on
different interfaces and of different kinds (e.g., General Queries,
Group-Specific Queries, and Group-and-Source-Specific Queries), each
of which may require its own delayed response.
Before scheduling a response to a Query, the system must first
consider previously scheduled pending responses and in many cases
schedule a combined response. Therefore, the system must be able to
maintain the following state:
o A timer per interface for scheduling responses to General Queries.
o A per-group and interface timer for scheduling responses to Group-
Specific and Group-and-Source-Specific Queries.
o A per-group and interface list of sources to be reported in the
response to a Group-and-Source-Specific Query.
When a new Query with the Router-Alert option arrives on an
interface, provided the system has state to report, a delay for a
response is randomly selected in the range (0, [Max Resp Time]) where
Max Resp Time is derived from Max Resp Code in the received Query
message. The following rules are then used to determine if a Report
needs to be scheduled and the type of Report to schedule. The rules
are considered in order and only the first matching rule is applied.
1. If there is a pending response to a previous General Query
scheduled sooner than the selected delay, no additional response
needs to be scheduled.
2. If the received Query is a General Query, the interface timer is
used to schedule a response to the General Query after the
selected delay. Any previously pending response to a General
Query is canceled.
--8<--
Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.
Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.
Signed-off-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__skb_flow_dissect can be called with a skb or a data packet, either
can be NULL. All calls seems to have been moved to __skb_header_pointer
except the pptp handling which is still calling skb_header_pointer.
skb_header_pointer will use skb->data and thus:
[ 109.556866] BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
[ 109.557102] IP: [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[ 109.557263] PGD 0
[ 109.557338]
[ 109.557484] Oops: 0000 [#1] SMP
[ 109.557562] Modules linked in: chaoskey
[ 109.557783] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.9.0 #79
[ 109.557867] Hardware name: Supermicro A1SRM-LN7F/LN5F/A1SRM-LN7F-2758, BIOS 1.0c 11/04/2015
[ 109.557957] task: ffff94085c27bc00 task.stack: ffffb745c0068000
[ 109.558041] RIP: 0010:[<ffffffff88dc02f8>] [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[ 109.558203] RSP: 0018:ffff94087fc83d40 EFLAGS: 00010206
[ 109.558286] RAX: 0000000000000130 RBX: ffffffff8975bf80 RCX: ffff94084fab6800
[ 109.558373] RDX: 0000000000000010 RSI: 000000000000000c RDI: 0000000000000000
[ 109.558460] RBP: 0000000000000b88 R08: 0000000000000000 R09: 0000000000000022
[ 109.558547] R10: 0000000000000008 R11: ffff94087fc83e04 R12: 0000000000000000
[ 109.558763] R13: ffff94084fab6800 R14: ffff94087fc83e04 R15: 000000000000002f
[ 109.558979] FS: 0000000000000000(0000) GS:ffff94087fc80000(0000) knlGS:0000000000000000
[ 109.559326] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 109.559539] CR2: 0000000000000080 CR3: 0000000281809000 CR4: 00000000001026e0
[ 109.559753] Stack:
[ 109.559957] 000000000000000c ffff94084fab6822 0000000000000001 ffff94085c2b5fc0
[ 109.560578] 0000000000000001 0000000000002000 0000000000000000 0000000000000000
[ 109.561200] 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 109.561820] Call Trace:
[ 109.562027] <IRQ>
[ 109.562108] [<ffffffff88dfb4fa>] ? eth_get_headlen+0x7a/0xf0
[ 109.562522] [<ffffffff88c5a35a>] ? igb_poll+0x96a/0xe80
[ 109.562737] [<ffffffff88dc912b>] ? net_rx_action+0x20b/0x350
[ 109.562953] [<ffffffff88546d68>] ? __do_softirq+0xe8/0x280
[ 109.563169] [<ffffffff8854704a>] ? irq_exit+0xaa/0xb0
[ 109.563382] [<ffffffff8847229b>] ? do_IRQ+0x4b/0xc0
[ 109.563597] [<ffffffff8902d4ff>] ? common_interrupt+0x7f/0x7f
[ 109.563810] <EOI>
[ 109.563890] [<ffffffff88d57530>] ? cpuidle_enter_state+0x130/0x2c0
[ 109.564304] [<ffffffff88d57520>] ? cpuidle_enter_state+0x120/0x2c0
[ 109.564520] [<ffffffff8857eacf>] ? cpu_startup_entry+0x19f/0x1f0
[ 109.564737] [<ffffffff8848d55a>] ? start_secondary+0x12a/0x140
[ 109.564950] Code: 83 e2 20 a8 80 0f 84 60 01 00 00 c7 04 24 08 00
00 00 66 85 d2 0f 84 be fe ff ff e9 69 fe ff ff 8b 34 24 89 f2 83 c2
04 66 85 c0 <41> 8b 84 24 80 00 00 00 0f 49 d6 41 8d 31 01 d6 41 2b 84
24 84
[ 109.569959] RIP [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[ 109.570245] RSP <ffff94087fc83d40>
[ 109.570453] CR2: 0000000000000080
Fixes: ab10dccb1160 ("rps: Inspect PPTP encapsulated by GRE to get flow hash")
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a leading line break else printed line gets too long.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.9
|
|
This patch does not change any functionality.
Fixes: e34cbd307477 ("blk-wbt: add general throttling mechanism")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Fixes: e34cbd307477 ("blk-wbt: add general throttling mechanism")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The first block to be cleaned may start at a non-zero page offset. In
such a scenario clean_bdev_aliases() will end up cleaning blocks that
do not fall in the range of blocks to be cleaned. This commit fixes the
issue by skipping blocks that do not fall in valid block range.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
While applying patch d443a0aa3a29: "HID: hid-sensor-hub: clear memory to
avoid random data", there was some issues in applying correct version of
the patch. This resulted in the breakage of sensor functions as all
request like power-up will be reset by the memset() in the function
sensor_hub_set_feature().
The reset of caller buffer should be in the function
sensor_hub_get_feature(), not in the sensor_hub_set_feature().
Fixes: d443a0aa3a29 ("HID: hid-sensor-hub: clear memory to avoid random data")
Cc: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The DolphinBar by Mayflash (identified as Dragonrise) needs
HID_QUIRK_MULTI_INPUT to split it up into four input devices. Without this
quirk the adapter is falsely recognized as a tablet. See also bug 115841
(https://bugzilla.kernel.org/show_bug.cgi?id=115841).
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Futaba TOSD-5711BB VFD crashes when the initial HID report is requested,
register the display in hid-ids and tell hid-quirks to not do the init.
Signed-off-by: Alex Wood <thetewood@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In ieee80211_xmit_fast(), 'info' is initialized to point to the skb
that's passed in, but that skb may later be replaced by a clone (if
it was shared), leading to an invalid pointer.
This can lead to use-after-free and also later crashes since the
real SKB's info->hw_queue doesn't get initialized properly.
Fix this by assigning info only later, when it's needed, after the
skb replacement (may have) happened.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For connected sockets, __l2tp_ip{,6}_bind_lookup() needs to check the
remote IP when looking for a matching socket. Otherwise a connected
socket can receive traffic not originating from its peer.
Drop l2tp_ip_bind_lookup() and l2tp_ip6_bind_lookup() instead of
updating their prototype, as these functions aren't used.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An L2TP socket bound to the unspecified address should match with any
address. If not, it can't receive any packet and __l2tp_ip6_bind_lookup()
can't prevent another socket from binding on the same device/tunnel ID.
While there, rename the 'addr' variable to 'sk_laddr' (local addr), to
make following patch clearer.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The build robot reports:
.tmp_kallsyms1.o: In function `kallsyms_relative_base':
>> (.rodata+0x8a18): undefined reference to `_text'
This is when using 'make alldefconfig'. Adding this _text symbol to mark
the start of the kernel as in other architecture fixes this.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
|
Paul Moore
David Forster
Grygorii Strashko
Lendacky, Thomas
Sergei Shtylyov
Zhu Yanjun
Johannes Berg
Edward Cree
Roy Pledge
Madalin Bucur
Florian Fainelli
Nicolas Pitre
Varun Prakash
Peter Chen
Arvind Yadav
Bartlomiej Zolnierkiewicz
Carlos Maiolino
Darrick J. Wong
Christoph Hellwig
David Ahern
Jeff Moyer
Kees Cook
Reiter Wolfgang
Sabrina Dubroca
Alexander Duyck
Bartosz Folta
Johan Hovold
Alexander Alemayhu
Michal Tesar
Ian Kumlien
Helge Deller
Bart Van Assche
Chandan Rajendra
Srinivas Pandruvada
Marcel Hasler
Alex Wood
Guillaume Nault
Stafford Horne