aboutsummaryrefslogtreecommitdiffstats
path: root/tools/perf/scripts/python/export-to-postgresql.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2017-10-29ARM: dts: meson8b: enable gpio interrupt controllerJerome Brunet2-0/+15
Add gpio interrupt controller node to the meson8b boards Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-10-29ARM: dts: meson8b: add support for booting the secondary CPU coresCarlo Caione1-0/+21
Booting the secondary CPU cores involves the following nodes/devices: - SCU (Snoop-Control-Unit, for which we already have a DT node) - a reset line for each CPU core, provided by the reset-controller which is built into the clock-controller - the PMU (power management unit) which controls the power of the CPU cores - a range in the SRAM specifically reserved for booting secondary CPU cores - the "enable-method" which activates booting the secondary CPU cores This adds all required nodes and properties to boot the secondary CPU cores. Signed-off-by: Carlo Caione <carlo@caione.org> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-10-29ARM: dts: meson8: add support for booting the secondary CPU coresMartin Blumenstingl1-0/+21
Booting the secondary CPU cores involves the following nodes/devices: - SCU (Snoop-Control-Unit, for which we already have a DT node) - a reset line for each CPU core, provided by the reset-controller which is built into the clock-controller - the PMU (power management unit) which controls the power of the CPU cores - a range in the SRAM specifically reserved for booting secondary CPU cores - the "enable-method" which activates booting the secondary CPU cores This adds all required nodes and properties to boot the secondary CPU cores. Suggested-by: Carlo Caione <carlo@caione.org> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-10-24ARM: dts: imx53-tx53: fix interrupt flagsLothar Waßmann2-3/+3
Some interrupts properties are given '0' as the flags argument or no flags argument at all. Change them to use the appropriate interrupt flags. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-24ARM: dts: imx28-tx28: fix interrupt flagsLothar Waßmann1-2/+2
Some interrupts properties are given '0' as the flags argument. Change them to use the appropriate interrupt flags. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-24arm64: dts: uniphier: add resets propertiesMasahiro Yamada3-0/+35
Add resets properties to all nodes that have reset lines. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24ARM: dts: uniphier: add resets propertiesMasahiro Yamada5-0/+52
Add resets properties to all nodes that have reset lines. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24arm64: dts: uniphier: add eMMC hardware reset provider nodeMasahiro Yamada3-0/+23
Add mmc-pwrseq-emmc node to perform standard eMMC hardware reset procedure. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24arm64: dts: uniphier: add GPIO hog definitionMasahiro Yamada2-0/+16
Interrupt lines from on-board devices are connected to the GPIO controller. Add GPIO hogging so that the corresponding GPIO line is automatically requested. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24arm64: dts: uniphier: route on-board device IRQ to GPIO controllerMasahiro Yamada2-2/+4
Interrupt lines from on-board devices are connected to the GPIO controller. Handle this correctly. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24arm64: dts: uniphier: add GPIO controller nodesMasahiro Yamada3-0/+63
The GPIO controller also acts as an interrupt controller and the interrupt lines are connected to the AIDET block. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24ARM: dts: uniphier: add GPIO hog definitionMasahiro Yamada4-0/+32
Interrupt lines from on-board devices are connected to the GPIO controller. Add GPIO hogging so that the corresponding GPIO line is automatically requested. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24ARM: dts: uniphier: route on-board device IRQ to GPIO controllerMasahiro Yamada5-4/+5
Interrupt lines from on-board devices are connected to the GPIO controller. Handle this correctly. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24ARM: dts: uniphier: add GPIO controller nodesMasahiro Yamada5-0/+77
The GPIO controller also acts as an interrupt controller and the interrupt lines are connected to the AIDET block. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-24arm64: dts: uniphier: fix W=2 build warningsMasahiro Yamada3-4/+4
Fix warnings like follows: Warning (node_name_chars_strict): Character '_' not recommended in ... Commit 8654cb8d0371 ("dtc: update warning settings for new bus and node/property name checks") says these checks are a bit subjective, but Rob also says to not add new W=2 warnings. The exising warnings should be fixed in order to catch new ones easily. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23arm64: dts: uniphier: enable NAND for PXs3 reference boardMasahiro Yamada1-0/+4
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23arm64: dts: uniphier: add efuse node for LD11, LD20, and PXs3Keiji Hayashibara3-0/+54
Add efuse node for UniPhier LD11, LD20, and PXs3. This efuse node is included in soc-glue. Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23ARM: dts: display5: Device tree description of LWN's DISPLAY5 boardLukasz Majewski3-0/+648
This commit adds device tree description of Liebherr's Display5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg propertyMarco Franchi1-1/+1
The following build warning is seen with W=1: Warning (unit_address_vs_reg): Node /soc/aips@50000000/iomuxc@53fa8000/imx53-qsb/led_gpio7_7@0 has a unit name, but no reg property Fix this warning by removing '@0' from such node. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg propertyMarco Franchi1-1/+1
The following build warning is seen with W=1: Warning (unit_address_vs_reg): Node /soc/aips@50000000/iomuxc@53fa8000/imx53-m53evk/led_gpio@0 has a unit name, but no reg property Fix this warning by removing '@0' from such node. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg propertyMarco Franchi1-2/+2
The following build warnings are seen with W=1: Warning (unit_address_vs_reg): Node /soc/aips@50000000/usbphy@0 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /soc/aips@50000000/usbphy@1 has a unit name, but no reg property Fix these warnings by changing '@' to '-'. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg propertyMarco Franchi1-1/+1
The following build warning is seen with W=1: Warning (unit_address_vs_reg): Node /display-di0/port@0 has a unit name, but no reg property Fix this warning by removing '@' from such node. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg propertyMarco Franchi1-2/+2
The following build warning is seen with W=1: Warning (unit_address_vs_reg): Node /backlight@bl1 has a unit name, but no reg property Fix this warning by removing '@bl1'from such node and change 'bl1grp' to 'backlightgrp', once there is only one backlight in this dts. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx: add ZII RDU1 boardLucas Stach2-1/+836
This adds support for the Zodiac Inflight Innovations RDU1 board, which is based on the i.MX51. It is the predecessor of the already supported ZII RDU2 board and relies on the bootloader in the same way to enable correct display and touchscreen nodes. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx: add support for TX6 modules on MB7 baseboardLothar Waßmann10-15/+403
Create .dts files for various Ka-Ro electronics TX modules on the MB7 baseboard. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx: add support for TX6QPLothar Waßmann3-0/+178
The TX6QP-8037 is a Computer On Module manufactured by Ka-Ro electronics GmbH with the following characteristics: Processor Freescale i.MX 6QuadPlus MCIMX6QP7, 1 GHz RAM 1GiB 64-bit DDR3 SDRAM ROM 4GB HiRel eMMC Power supply Single 3.3 to 5V Size 26mm SO-DIMM Temp. Range -40°C to 105°C Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboardLothar Waßmann3-48/+102
Move the MB7 specific settings to a separate .dtsi file to facilitate supporting more module variants with this baseboard. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: move display configuration to .dtsi fileLothar Waßmann17-1902/+616
Currently the display (LCD or LVDS) configuration is duplicated with slight variations in each TX6 module specific file. Move it to an include file for simplification and consistency. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: add support for I2C bus recoveryLothar Waßmann1-2/+22
Define the required properties to enable I2C bus recovery supported by the I2C subsystem. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: convert to using simple-audio-cardLothar Waßmann1-8/+42
Convert the DTS sound setup to use the simple-audio-card driver. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: specify ethernet phy reset post-delayLothar Waßmann1-0/+1
Under certain circumstances the ethernet PHY cannot be detected on Ka-Ro electronics TX6 modules. Using a phy-reset-post-delay of at least 2ms alleviates this problem. Define it to 10ms to be on the safe side. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: improve ethernet related pinctrl setupLothar Waßmann1-6/+17
Remove the PHY INT and RESET pins from hog section and put them into their own pinctrl nodes referenced by the appropriate driver nodes. Also, the MDIO pins are required for probing the Ethernet PHY, so they must be configured by the FEC driver, not by the PHY driver. Move the corresponding pinctrl settings from the PHY subnode to the FEC node. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: add trickle-charge config for DS1339Lothar Waßmann1-0/+2
As the DS1339 driver now supports enabling the trickle charge feature via DTB, add the appropriate properties to utilize this feature. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: remove obsolete ipu1 aliasLothar Waßmann1-1/+0
The 'ipu1' alias is already defined in imx6q.dtsi. There is no need to redefine it here. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: remove obsolete eeti,egalax_tsLothar Waßmann4-85/+3
The display, that incorporates this touchpanel is obsolete and won't be supported any more. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6-tx6: update model property to match current module HW revisionLothar Waßmann2-4/+4
The current TX6Q module HW revision is 3 reflected in the module name suffix '-1030' (-1130 for LVDS). Change the model string to prevent confusion about what DTS file to use for these modules. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx25-eukrea-mbimxsd25-baseboard: Fix the 'cd-gpios' propertyFabio Estevam1-1/+1
The GPIO polarity is missing in the cd-gpios property. Fix it, so that the following build warnings are gone: DTC arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dtb arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dtb: Warning (gpios_property): cd-gpios property size (8) too small for cell size 2 in /soc/aips@53f00000/esdhc@53fb4000 DTC arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dtb arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dtb: Warning (gpios_property): cd-gpios property size (8) too small for cell size 2 in /soc/aips@53f00000/esdhc@53fb4000 DTC arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dtb arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dtb: Warning (gpios_property): cd-gpios property size (8) too small for cell size 2 in /soc/aips@53f00000/esdhc@53fb4000 DTC arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb: Warning (gpios_property): cd-gpios property size (8) too small for cell size 2 in /soc/aips@53f00000/esdhc@53fb4000 Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx50: Pass the 'dma-cells' propertyFabio Estevam1-0/+1
Pass the '#dma-cells' property in the sdma node, so that the following build warning is gone: DTC arch/arm/boot/dts/imx50-evk.dtb arch/arm/boot/dts/imx50-evk.dtb: Warning (dmas_property): Missing property '#dma-cells' in node /soc/aips@60000000/sdma@63fb0000 or bad phandle (referred from /soc/aips@50000000/spba@50000000/ssi@50014000:dmas[0]) Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx35-eukrea-mbimxsd35-baseboard: Fix the 'cd-gpios' propertyFabio Estevam1-1/+1
The GPIO polarity is missing in the cd-gpios property. Fix it, so that the following build warning is gone: DTC arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dtb arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dtb: Warning (gpios_property): cd-gpios property size (8) too small for cell size 2 in /soc/aips@53f00000/esdhc@53fb400 Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6sx-softing-vining-2000: Fix the 'interrupt-parent' propertyFabio Estevam1-2/+2
The correct property name is 'interrupt-parent', so fix it accordingly. This fixes the following build warning: arch/arm/boot/dts/imx6sx-softing-vining-2000.dtb: Warning (interrupts_property): interrupts size is (8), expected multiple of 12 in /soc/aips-bus@02100000/ethernet@02188000/mdio/ethernet0-phy@0 arch/arm/boot/dts/imx6sx-softing-vining-2000.dtb: Warning (interrupts_property): interrupts size is (8), expected multiple of 12 in /soc/aips-bus@02100000/ethernet@021b4000/mdio/ethernet1-phy@0 Cc: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6ul-pico-hobbit: Fix the 'interrupts' propertyFabio Estevam1-1/+1
The 'interrupts' property has an extra cell by mistake. Fix this, so that the following build warning is gone: DTC arch/arm/boot/dts/imx6ul-pico-hobbit.dtb arch/arm/boot/dts/imx6ul-pico-hobbit.dtb: Warning (interrupts_property): interrupts size is (12), expected multiple of 8 in /soc/aips-bus@2000000/ethernet@20b4000/mdio/ethernet-phy@1 Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6qp-wandboard-revd1: Add sata supportFabio Estevam1-0/+4
The imx6qp variant also has sata, so add support for it. Reported-by: Luís Mendes <luis.p.mendes@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6q-cm-fx6: Use the 'vpcie-supply' propertyFabio Estevam1-3/+2
According to Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt, the property for specifying the PCIe regulator is 'vpcie-supply', so use the correct one. Also fix the polarity of GPIO2_24 so that the regulator can operate correctly. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6q-novena: Use the 'vpcie-supply' propertyFabio Estevam1-1/+1
Since commit c26ebe98a103 ("PCI: imx6: Add regulator support"), it is possible to pass the 'vpcie-supply' property to describe the PCIE supply. This way we can remove the 'regulator-always-on' property from the regulator and have a better device tree description. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6ul: Add imx6ul-tempmonLeonard Crestez1-0/+19
This works identically to imx6sx-tempmon on both imx6ul and imx6ull. It just needs to be defined in dts. Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6sx: Use nvmem-cells for tempmonLeonard Crestez1-1/+12
On imx6sx accessing OCOTP directly is wrong because the ocotp clock needs to be enabled first. Use the nvmem-cells binding instead. This requirement does not apply to older imx6qdl chips because there the ocotp access clock (clk_ipg_s) is always enabled. This is visible by comparing the "System Clocks, Gating, and Override" tables (OCOTP rows) in the 6DQ and 6SX manuals: http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6SXRM.pdf http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6DQRM.pdf This happens to work right now because the ocotp clock might be enabled for some other reason. In particular the it might be enabled from the bootloader and it only gets disabled late during boot in clk_disable_unused, after imx-thermal has completed probing. If imx-thermal is compiled as a module then the system can hang on probe. Reported-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx: ventana: remove container node from iomuxc nodesTim Harvey7-998/+983
The container node in the iomuxc node is no longer necessary and causes pinctl errors on the Ventana boards with analog video capture since aa12693e4156adafdef80a8bd134123a6419621b: pinctrl core: initialized pinctrl subsystem imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/adv7180grp imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/ipu2_csi1grp imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6qdl-wandboard: Add support for the revd1 variantsFabio Estevam5-0/+269
Latest wandboard hardware revision is revd1, which brings the following new features: - PFUZE100 PMIC - AR8035 Ethernet PHY - Upgrade Wifi/BT chip to BCM4339/BCM43430. Add support for the mx6, mx6dl and mx6qp revd1 variants. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx6ul-14x14-evk: switch lcdif pixel clock to video pllPhilipp Zabel1-0/+2
By default, the lcdif_pre_sel mux is switched to the pll3_pfd1_540m PFD source. If this mux is allowed to propagate rate changes to its parent, setting the LCDIF pixel clock rate to 9 MHz, as required by the LCD panel, will cause the pll3_pfd1_540m PFD to be switched away from its nominal rate to 288 MHz. This has no negative side effects, as there are no other children to this PFD. Still, to avoid surprises, it might be preferrable to switch to the designated video PLL (pll5_video_div) as clock source for the LCDIF pixel clock. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-10-23ARM: dts: imx53-tx53: add support for I2C bus recoveryLothar Waßmann2-2/+22
The imx-i2c driver supports automatic bus recovery via the GPIO function of the I2C pins. Enable this functionality for the Ka-Ro electronics TX53 modules. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.