| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Crosslink is a feature of the Switchtec switches that is similar to
the B2B mode of other NTB devices. It allows a system to be designed
that is perfectly symmetric with two identical switches that link
two hosts together.
In order for the system to be symmetric, there is an empty host-less
partition between the two switches which the host must enumerate and
assign BAR addresses to. The firmware in the switch manages this
specially so that the BAR addresses on both sides of the empty
partition will be identical despite being in the same partition with
the same address space.
The driver determines whether crosslink is enabled by a flag set in
the NTB partition info registers which are set by the switch's
configuration file.
When crosslink is enabled, a reserved LUT window is setup to point to
the peer's switch's NTB registers and the local MWs are set to forward
to the host-less partition's BARs. (Yes, this hurts my brain too.)
Once this is setup, largely the same NTB infrastructure is used to
communicate between the two hosts.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The PFF CSR registers actual mirrors the PCI configuration space
for all the ports in the switch. Previously, this was not needed by
the driver but will be used by the crosslink code to enumerate the
bus in an host-less centre partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This is a prep patch in order to support the crosslink feature which
will require the driver to setup the requester ID table in another
partition as well as it's own. To aid this, create a helper function
which sets up the requester IDs from an array.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This is a prep patch in order to support the crosslink feature which
will require the driver to use another reserved LUT window. To
simplify this we move the code which sets up the reserved LUT window
into a helper function which will be used by the crosslink
initialization.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This is a prep patch in order to support the crosslink feature which will
require the driver to use another reserved LUT window. To simplify this,
we add some code to track the number of reserved LUT windows in use
instead of assuming this is always 1.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Allow using Switchtec NTB in setups that have more than two partitions.
Note: this does not enable having multi-host communication, it only
allows for a single NTB link between two hosts in a network that might
have more than two.
Use following logic to determine the NT peer partition:
1) If there are 2 partitions, and the target vector is set in
the Switchtec configuration, use the partition specified in target
vector.
2) If there are 2 partitions and target vector is unset
use the only other partition as specified in the NT EP map.
3) If there are more than 2 partitions and target vector is set
use the other partition specified in target vector.
4) If there are more than 2 partitions and target vector is unset,
this is invalid and report an error.
Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com>
[logang@deltatee.com: commit message fleshed out]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Trivial addition of "\n" to the dev_* prints where necessary
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-By: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Removing dead code since this is not being used.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference, especially when the string is defined just a few
lines above the usage of it.
Reported-and-reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Gary R Hook <gary.hook@amd.com>
Cc: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This resolves a bug which may incorrectly configure the peer host's
LUT for shared memory window access. The code was using the local
host's first BAR number, rather than the peer hosts's first BAR
number, to determine what peer NT control register to program.
The bug will cause the Switchtec NTB link to work only if both peers
have the same first NTB BAR configured. In all other configurations,
the link will not come up, failing silently.
When both hosts have the same first BAR, the configuration works only
because the first BAR numbers happent to be the same. When the hosts
do not have the same first BAR, then the LUT translation will not be
configured in the correct peer LUT and will not give the peer the
shared memory window access required for the link to operate.
Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: 678784a44ae8 ("NTB: switchtec_ntb: Initialize hardware for memory windows")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
|
|
When ORC support was added for the ftrace_64.S code, an ENDPROC
for function_hook() was missed. This results in the following warning:
arch/x86/kernel/ftrace_64.o: warning: objtool: .entry.text+0x0: unreachable instruction
Fixes: e2ac83d74a4d ("x86/ftrace: Fix ORC unwinding from ftrace handlers")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180128022150.dqierscqmt3uwwsr@treble
|
|
The hrtimer interrupt code contains a hang detection and mitigation
mechanism, which prevents that a long delayed hrtimer interrupt causes a
continous retriggering of interrupts which prevent the system from making
progress. If a hang is detected then the timer hardware is programmed with
a certain delay into the future and a flag is set in the hrtimer cpu base
which prevents newly enqueued timers from reprogramming the timer hardware
prior to the chosen delay. The subsequent hrtimer interrupt after the delay
clears the flag and resumes normal operation.
If such a hang happens in the last hrtimer interrupt before a CPU is
unplugged then the hang_detected flag is set and stays that way when the
CPU is plugged in again. At that point the timer hardware is not armed and
it cannot be armed because the hang_detected flag is still active, so
nothing clears that flag. As a consequence the CPU does not receive hrtimer
interrupts and no timers expire on that CPU which results in RCU stalls and
other malfunctions.
Clear the flag along with some other less critical members of the hrtimer
cpu base to ensure starting from a clean state when a CPU is plugged in.
Thanks to Paul, Sebastian and Anna-Maria for their help to get down to the
root cause of that hard to reproduce heisenbug. Once understood it's
trivial and certainly justifies a brown paperbag.
Fixes: 41d2e4949377 ("hrtimer: Tune hrtimer_interrupt hang logic")
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801261447590.2067@nanos
|
|
Due to some unfortunate events, I have not been directly involved in
the x86 kernel patch flow for a while now. I have also not been able
to ramp back up by now like I had hoped to, and after reviewing what I
will need to work on both internally at Intel and elsewhere in the near
term, it is clear that I am not going to be able to ramp back up until
late 2018 at the very earliest.
It is not acceptable to not recognize that this load is currently
taken by Ingo and Thomas without my direct participation, so I mark
myself as R: (designated reviewer) rather than M: (maintainer) until
further notice. This is in fact recognizing the de facto situation
for the past few years.
I have obviously no intention of going away, and I will do everything
within my power to improve Linux on x86 and x86 for Linux. This,
however, puts credit where it is due and reflects a change of focus.
This patch also removes stale entries for portions of the x86
architecture which have not been maintained separately from arch/x86
for a long time. If there is a reason to re-introduce them then that
can happen later.
Signed-off-by: H. Peter Anvin <h.peter.anvin@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bruce Schlobohm <bruce.schlobohm@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180125195934.5253-1-hpa@zytor.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
select(2) with wfds but no rfds must return when the socket is shut down
by the peer. This way userspace notices socket activity and gets -EPIPE
from the next write(2).
Currently select(2) does not return for virtio-vsock when a SEND+RCV
shutdown packet is received. This is because vsock_poll() only sets
POLLOUT | POLLWRNORM for TCP_CLOSE, not the TCP_CLOSING state that the
socket is in when the shutdown is received.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ccid2_hc_tx_rto_expire() timer callback always restarts the timer
again and can run indefinitely (unless it is stopped outside), and after
commit 120e9dabaf55 ("dccp: defer ccid_hc_tx_delete() at dismantle time"),
which moved ccid_hc_tx_delete() (also includes sk_stop_timer()) from
dccp_destroy_sock() to sk_destruct(), this started to happen quite often.
The timer prevents releasing the socket, as a result, sk_destruct() won't
be called.
Found with LTP/dccp_ipsec tests running on the bonding device,
which later couldn't be unloaded after the tests were completed:
unregister_netdevice: waiting for bond0 to become free. Usage count = 148
Fixes: 2a91aa396739 ("[DCCP] CCID2: Initial CCID2 (TCP-Like) implementation")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we're upstream in Linux we've been able to make some
infrastructure changes so our port works a bit more like other ports.
Specifically:
* We now have a mailing list specific to the RISC-V Linux port, hosted
at lists.infreadead.org.
* We now have a kernel.org git tree where work on our port is
coordinated.
This patch changes the RISC-V maintainers entry to reflect these new
bits of infrastructure.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
On a 5-level kernel, if a non-init mm has a top-level entry, it needs to
match init_mm's, but the vmalloc_fault() code skipped over the BUG_ON()
that would have checked it.
While we're at it, get rid of the rather confusing 4-level folded "pgd"
logic.
Cleans-up: b50858ce3e2a ("x86/mm/vmalloc: Add 5-level paging support")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Neil Berrington <neil.berrington@datacore.com>
Link: https://lkml.kernel.org/r/2ae598f8c279b0a29baf75df207e6f2fdddc0a1b.1516914529.git.luto@kernel.org
|
|
Neil Berrington reported a double-fault on a VM with 768GB of RAM that uses
large amounts of vmalloc space with PTI enabled.
The cause is that load_new_mm_cr3() was never fixed to take the 5-level pgd
folding code into account, so, on a 4-level kernel, the pgd synchronization
logic compiles away to exactly nothing.
Interestingly, the problem doesn't trigger with nopti. I assume this is
because the kernel is mapped with global pages if we boot with nopti. The
sequence of operations when we create a new task is that we first load its
mm while still running on the old stack (which crashes if the old stack is
unmapped in the new mm unless the TLB saves us), then we call
prepare_switch_to(), and then we switch to the new stack.
prepare_switch_to() pokes the new stack directly, which will populate the
mapping through vmalloc_fault(). I assume that we're getting lucky on
non-PTI systems -- the old stack's TLB entry stays alive long enough to
make it all the way through prepare_switch_to() and switch_to() so that we
make it to a valid stack.
Fixes: b50858ce3e2a ("x86/mm/vmalloc: Add 5-level paging support")
Reported-and-tested-by: Neil Berrington <neil.berrington@datacore.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: stable@vger.kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/346541c56caed61abbe693d7d2742b4a380c5001.1516914529.git.luto@kernel.org
|
|
Sukumar reported that sends to the local broadcast address
(255.255.255.255) are broken. Check for the address in vrf driver
and do not redirect to the VRF device - similar to multicast
packets.
With this change sockets can use SO_BINDTODEVICE to specify an
egress interface and receive responses. Note: the egress interface
can not be a VRF device but needs to be the enslaved device.
https://bugzilla.kernel.org/show_bug.cgi?id=198521
Reported-by: Sukumar Gopalakrishnan <sukumarg1973@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware statistics retrieval hurts in tight invocation loops.
Avoid extraneous write and enforce strict ordering of writes targeted to
the tally counters dump area address registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Oliver Freyermuth <o.freyermuth@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After do_readv_writev, the inode cache is invalidated anyway, so i_size
will never be read. It will be fetched from the server which will also
know about updates from other machines.
Fixes deadlock on 32-bit SMP.
See https://marc.info/?l=linux-fsdevel&m=151268557427760&w=2
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mike Marshall <hubcap@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For a while we've been having issues with seemingly random interrupts
coming from nvidia cards when resuming them. Originally the fix for this
was thought to be just re-arming the MSI interrupt registers right after
re-allocating our IRQs, however it seems a lot of what we do is both
wrong and not even nessecary.
This was made apparent by what appeared to be a regression in the
mainline kernel that started introducing suspend/resume issues for
nouveau:
a0c9259dc4e1 (irq/matrix: Spread interrupts on allocation)
After this commit was introduced, we started getting interrupts from the
GPU before we actually re-allocated our own IRQ (see references below)
and assigned the IRQ handler. Investigating this turned out that the
problem was not with the commit, but the fact that nouveau even
free/allocates it's irqs before and after suspend/resume.
For starters: drivers in the linux kernel haven't had to handle
freeing/re-allocating their IRQs during suspend/resume cycles for quite
a while now. Nouveau seems to be one of the few drivers left that still
does this, despite the fact there's no reason we actually need to since
disabling interrupts from the device side should be enough, as the
kernel is already smart enough to know to disable host-side interrupts
for us before going into suspend. Since we were tearing down our IRQs by
hand however, that means there was a short period during resume where
interrupts could be received before we re-allocated our IRQ which would
lead to us getting an unhandled IRQ. Since we never handle said IRQ and
re-arm the interrupt registers, this would cause us to miss all of the
interrupts from the GPU and cause our init process to start timing out
on anything requiring interrupts.
So, since this whole setup/teardown every suspend/resume cycle is
useless anyway, move irq setup/teardown into the pci subdev's ctor/dtor
functions instead so they're only called at driver load and driver
unload. This should fix most of the issues with pending interrupts on
resume, along with getting suspend/resume for nouveau to work again.
As well, this probably means we can also just remove the msi rearm call
inside nvkm_pci_init(). But since our main focus here is to fix
suspend/resume before 4.15, we'll save that for a later patch.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Some dst_ops (e.g. md_dst_ops)) doesn't set this handler. It may result to:
"BUG: unable to handle kernel NULL pointer dereference at (null)"
Let's add a helper to check if update_pmtu is available before calling it.
Fixes: 52a589d51f10 ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff4490 ("vxlan: update skb dst pmtu on tx path")
CC: Roman Kapl <code@rkapl.cz>
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
More lockdep gifts, a 5-way lockup race:
perf_event_create_kernel_counter()
perf_event_alloc()
perf_try_init_event()
x86_pmu_event_init()
__x86_pmu_event_init()
x86_reserve_hardware()
#0 mutex_lock(&pmc_reserve_mutex);
reserve_ds_buffer()
#1 get_online_cpus()
perf_event_release_kernel()
_free_event()
hw_perf_event_destroy()
x86_release_hardware()
#0 mutex_lock(&pmc_reserve_mutex)
release_ds_buffer()
#1 get_online_cpus()
#1 do_cpu_up()
perf_event_init_cpu()
#2 mutex_lock(&pmus_lock)
#3 mutex_lock(&ctx->mutex)
sys_perf_event_open()
mutex_lock_double()
#3 mutex_lock(ctx->mutex)
#4 mutex_lock_nested(ctx->mutex, 1);
perf_try_init_event()
#4 mutex_lock_nested(ctx->mutex, 1)
x86_pmu_event_init()
intel_pmu_hw_config()
x86_add_exclusive()
#0 mutex_lock(&pmc_reserve_mutex)
Fix it by using ordering constructs instead of locking.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Lockdep noticed the following 3-way lockup scenario:
sys_perf_event_open()
perf_event_alloc()
perf_try_init_event()
#0 ctx = perf_event_ctx_lock_nested(1)
perf_swevent_init()
swevent_hlist_get()
#1 mutex_lock(&pmus_lock)
perf_event_init_cpu()
#1 mutex_lock(&pmus_lock)
#2 mutex_lock(&ctx->mutex)
sys_perf_event_open()
mutex_lock_double()
#2 mutex_lock()
#0 mutex_lock_nested()
And while we need that perf_event_ctx_lock_nested() for HW PMUs such
that they can iterate the sibling list, trying to match it to the
available counters, the software PMUs need do no such thing. Exclude
them.
In particular the swevent triggers the above invertion, while the
tpevent PMU triggers a more elaborate one through their event_mutex.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Lockdep noticed the following 3-way lockup race:
perf_trace_init()
#0 mutex_lock(&event_mutex)
perf_trace_event_init()
perf_trace_event_reg()
tp_event->class->reg() := tracepoint_probe_register
#1 mutex_lock(&tracepoints_mutex)
trace_point_add_func()
#2 static_key_enable()
#2 do_cpu_up()
perf_event_init_cpu()
#3 mutex_lock(&pmus_lock)
#4 mutex_lock(&ctx->mutex)
perf_ioctl()
#4 ctx = perf_event_ctx_lock()
_perf_iotcl()
ftrace_profile_set_filter()
#0 mutex_lock(&event_mutex)
Fudge it for now by noting that the tracepoint state does not depend
on the event <-> context relation. Ugly though :/
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Lockdep gifted us with noticing the following 4-way lockup scenario:
perf_trace_init()
#0 mutex_lock(&event_mutex)
perf_trace_event_init()
perf_trace_event_reg()
tp_event->class->reg() := tracepoint_probe_register
#1 mutex_lock(&tracepoints_mutex)
trace_point_add_func()
#2 static_key_enable()
#2 do_cpu_up()
perf_event_init_cpu()
#3 mutex_lock(&pmus_lock)
#4 mutex_lock(&ctx->mutex)
perf_event_task_disable()
mutex_lock(¤t->perf_event_mutex)
#4 ctx = perf_event_ctx_lock()
#5 perf_event_for_each_child()
do_exit()
task_work_run()
__fput()
perf_release()
perf_event_release_kernel()
#4 mutex_lock(&ctx->mutex)
#5 mutex_lock(&event->child_mutex)
free_event()
_free_event()
event->destroy() := perf_trace_destroy
#0 mutex_lock(&event_mutex);
Fix that by moving the free_event() out from under the locks.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the sysfs attribute hangs off the RMI bus, which doesn't go away during
firmware flash, it needs to be explicitly removed, otherwise we would try and
register the same attribute twice.
This reverts commit 36a44af5c176d619552d99697433261141dd1296.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The code will try to access dev->iotlb when processing
VHOST_IOTLB_INVALIDATE even if it was not initialized which may lead
to NULL pointer dereference. Fixes this by check dev->iotlb before.
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API")
Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a768b7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the typo CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64
Fixes: 81658ad0d923 ("sparc64: Add CAMELLIA driver making use of the new camellia opcodes.")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed to prevent sk_user_data being overwritten.
The check is done under the callback lock. This should prevent
a socket from being attached twice to a KCM mux. It also prevents
a socket from being attached for other use cases of sk_user_data
as long as the other cases set sk_user_data under the lock.
Followup work is needed to unify all the use cases of sk_user_data
to use the same locking.
Reported-by: syzbot+114b15f2be420a8886c3@syzkaller.appspotmail.com
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP sockets for IPv4 and IPv6 that are not listeners or in closed
stated are allowed to be attached to a KCM mux.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+8865eaff7f9acd593945@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update my email address.
Signed-off-by: James Morris <jmorris@namei.org>
|
|
TCF_LAYER_LINK and TCF_LAYER_NETWORK returned the same pointer as
skb->data points to the network header.
Use skb_mac_header instead.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ptr' is shifted by the offset and then validated,
the memcmp should not add it a second time.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In fixing the readdir+pagefault deadlock I accidentally introduced a
stale entry regression in readdir. If we get close to full for the
temporary buffer, and then skip a few delayed deletions, and then try to
add another entry that won't fit, we will emit the entries we found and
retry. Unfortunately we delete entries from our del_list as we find
them, assuming we won't need them. However our pos will be with
whatever our last entry was, which could be before the delayed deletions
we skipped, so the next search will add the deleted entries back into
our readdir buffer. So instead don't delete entries we find in our
del_list so we can make sure we always find our delayed deletions. This
is a slight perf hit for readdir with lots of pending deletions, but
hopefully this isn't a common occurrence. If it is we can revist this
and optimize it.
cc: stable@vger.kernel.org
Fixes: 23b5ec74943f ("btrfs: fix readdir deadlock with pagefault")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We're seeing a raise of automated reports from testing tools and reports
about address leaks that are not really exploitable as-is, many of which
do not represent an immediate risk justifying to work in closed places.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 6cfb521ac0d5b97470883ff9b7facae264b7ab12.
Turns out distros do not want to make retpoline as part of their "ABI",
so this patch should not have been merged. Sorry Andi, this was my
fault, I suggested it when your original patch was the "correct" way of
doing this instead.
Reported-by: Jiri Kosina <jikos@kernel.org>
Fixes: 6cfb521ac0d5 ("module: Add retpoline tag to VERMAGIC")
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.
Simply remove the error message and gracefully accept such events.
Fixes: c723c735fa6b ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca11b9 ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some parts of the cmma migration bitmap is already protected
with the kvm->lock (e.g. the migration start). On the other
hand the read of the cmma bits is not protected against a
concurrent free, neither is the emulation of the ESSA instruction.
Let's extend the locking to all related ioctls by using
the slots lock for
- kvm_s390_vm_start_migration
- kvm_s390_vm_stop_migration
- kvm_s390_set_cmma_bits
- kvm_s390_get_cmma_bits
In addition to that, we use synchronize_srcu before freeing
the migration structure as all users hold kvm->srcu for read.
(e.g. the ESSA handler).
Reported-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org # 4.13+
Fixes: 190df4a212a7 (KVM: s390: CMMA tracking, ESSA emulation, migration mode)
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
|
|
Commit 24c2503255d3 ("x86/microcode: Do not access the initrd after it has
been freed") fixed attempts to access initrd from the microcode loader
after it has been freed. However, a similar KASAN warning was reported
(stack trace edited):
smpboot: Booting Node 0 Processor 1 APIC 0x11
==================================================================
BUG: KASAN: use-after-free in find_cpio_data+0x9b5/0xa50
Read of size 1 at addr ffff880035ffd000 by task swapper/1/0
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.14.8-slack #7
Hardware name: System manufacturer System Product Name/A88X-PLUS, BIOS 3003 03/10/2016
Call Trace:
dump_stack
print_address_description
kasan_report
? find_cpio_data
__asan_report_load1_noabort
find_cpio_data
find_microcode_in_initrd
__load_ucode_amd
load_ucode_amd_ap
load_ucode_ap
After some investigation, it turned out that a merge was done using the
wrong side to resolve, leading to picking up the previous state, before
the 24c2503255d3 fix. Therefore the Fixes tag below contains a merge
commit.
Revert the mismerge by catching the save_microcode_in_initrd_amd()
retval and thus letting the function exit with the last return statement
so that initrd_gone can be set to true.
Fixes: f26483eaedec ("Merge branch 'x86/urgent' into x86/microcode, to resolve conflicts")
Reported-by: <higuita@gmx.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198295
Link: https://lkml.kernel.org/r/20180123104133.918-2-bp@alien8.de
|
Logan Gunthorpe
Kelvin Cao
Jon Mason
Colin Ian King
Dave Jiang
Greg Kroah-Hartman
Doug Meyer
Linus Torvalds
Josh Poimboeuf
Thomas Gleixner
H. Peter Anvin
Stefan Hajnoczi
Alexey Kodanev
Palmer Dabbelt
Andy Lutomirski
David Ahern
Francois Romieu
Martin Brandenburg
Lyude Paul
Nicolas Dichtel
Dan Streetman
Peter Zijlstra
Ivan Mikhaylov
Nick Dyer
Jason Wang
Jakub Kicinski
Corentin Labbe
Michal Kalderon
Tom Herbert
James Morris
Wolfgang Bumiller
Josef Bacik
Willy Tarreau
Yuval Mintz
Christian Borntraeger
Borislav Petkov