| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With the current code, ids are removed too early.
Suppose you have an ipip interface that stands in the netns foo and its link
part in the netns bar (so the netns bar has an nsid into the netns foo).
Now, you remove the netns bar:
- the bar nsid into the netns foo is removed
- the netns exit method of ipip is called, thus our ipip iface is removed:
=> a netlink message is sent in the netns foo to advertise this deletion
=> this netlink message requests an nsid for bar, thus a new nsid is
allocated for bar and never removed.
We must remove nsids when we are sure that nobody will refer to netns currently
cleaned.
Fixes: 0c7aecd4bde4 ("netns: add rtnl cmd to add and get peer netns ids")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable interrupts and quiesce rx before unregistering net device to avoid crash
while unloading driver when traffic is flowing through.
Based on original work by Shameem Khalid <shameem@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QIDs (egress/ingress) from firmware in FW_*_CMD.alloc command
can be anywhere in the range from EQ(IQFLINT)_START to EQ(IQFLINT)_END.
For eg, in the first load eqid can be from 100 to 300.
In the next load it can be from 301 to 500 (assume eq_start is 100 and eq_end is
1000).
The driver was assuming them to always start from EQ(IQFLINT)_START till
MAX_EGRQ(INGQ). This was causing stack overflow and subsequent crash.
Fixed it by dynamically allocating memory (of qsize (x_END - x_START + 1)) for
these structures.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Fixes: beeecd42c3b4 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
|
|
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes below warning by dynamically allocating memory
All warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c: In function
'cctrl_tbl_show':
>> drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:689:1: warning: the
>> frame
>> size of 1028 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A local route may have a lower hop_limit set than global routes do.
RFC 3756, Section 4.2.7, "Parameter Spoofing"
> 1. The attacker includes a Current Hop Limit of one or another small
> number which the attacker knows will cause legitimate packets to
> be dropped before they reach their destination.
> As an example, one possible approach to mitigate this threat is to
> ignore very small hop limits. The nodes could implement a
> configurable minimum hop limit, and ignore attempts to set it below
> said limit.
Signed-off-by: D.S. Ljungmark <ljungmark@modio.se>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ucc_geth was indicating link up after a port is administratively enabled even
when nothing is plugged in. This causes user-space tools to see a spurious link
up the first time after boot.
Signed-off-by: Cliff Clark <cliff_clark@selinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We occasionally see in procedure mlx4_GEN_EQE that the driver tries
to grab an uninitialized mutex.
This can occur in only one of two ways:
1. We are trying to generate an async event on an uninitialized slave.
2. We are trying to generate an async event on an illegal slave number
( < 0 or > persist->num_vfs) or an inactive slave.
To deal with #1: move the mutex initialization from specific slave init
sequence in procedure mlx_master_do_cmd to mlx4_multi_func_init() (so that
the mutex is always initialized for all slaves).
To deal with #2: check in procedure mlx4_GEN_EQE that the slave number
provided is in the proper range and that the slave is active.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.
For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.
Fixes: 837052d0ccc5 ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch.
Previously in those cases rocker_port_bridge_leave() was called
which results in a null-pointer dereference as rocker_port->bridge_dev
is NULL because there is no bridge device.
This patch makes provision for doing nothing in such cases.
Fixes: 6c7079450071f ("rocker: implement L2 bridge offloading")
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we move the whole dev group to another netns,
we should call for_each_netdev_safe(), otherwise we get
a soft lockup:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [ip:798]
irq event stamp: 255424
hardirqs last enabled at (255423): [<ffffffff81a2aa95>] restore_args+0x0/0x30
hardirqs last disabled at (255424): [<ffffffff81a2ad5a>] apic_timer_interrupt+0x6a/0x80
softirqs last enabled at (255422): [<ffffffff81079ebc>] __do_softirq+0x2c1/0x3a9
softirqs last disabled at (255417): [<ffffffff8107a190>] irq_exit+0x41/0x95
CPU: 0 PID: 798 Comm: ip Not tainted 4.0.0-rc4+ #881
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task: ffff8800d1b88000 ti: ffff880119530000 task.ti: ffff880119530000
RIP: 0010:[<ffffffff810cad11>] [<ffffffff810cad11>] debug_lockdep_rcu_enabled+0x28/0x30
RSP: 0018:ffff880119533778 EFLAGS: 00000246
RAX: ffff8800d1b88000 RBX: 0000000000000002 RCX: 0000000000000038
RDX: 0000000000000000 RSI: ffff8800d1b888c8 RDI: ffff8800d1b888c8
RBP: ffff880119533778 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 000000000000b5c2 R12: 0000000000000246
R13: ffff880119533708 R14: 00000000001d5a40 R15: ffff88011a7d5a40
FS: 00007fc01315f740(0000) GS:ffff88011a600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f367a120988 CR3: 000000011849c000 CR4: 00000000000007f0
Stack:
ffff880119533798 ffffffff811ac868 ffffffff811ac831 ffffffff811ac828
ffff8801195337c8 ffffffff811ac8c9 ffff8801195339b0 ffff8801197633e0
0000000000000000 ffff8801195339b0 ffff8801195337d8 ffffffff811ad2d7
Call Trace:
[<ffffffff811ac868>] rcu_read_lock+0x37/0x6e
[<ffffffff811ac831>] ? rcu_read_unlock+0x5f/0x5f
[<ffffffff811ac828>] ? rcu_read_unlock+0x56/0x5f
[<ffffffff811ac8c9>] __fget+0x2a/0x7a
[<ffffffff811ad2d7>] fget+0x13/0x15
[<ffffffff811be732>] proc_ns_fget+0xe/0x38
[<ffffffff817c7714>] get_net_ns_by_fd+0x11/0x59
[<ffffffff817df359>] rtnl_link_get_net+0x33/0x3e
[<ffffffff817df3d7>] do_setlink+0x73/0x87b
[<ffffffff810b28ce>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff81a2aa95>] ? retint_restore_args+0xe/0xe
[<ffffffff817e0301>] rtnl_newlink+0x40c/0x699
[<ffffffff817dffe0>] ? rtnl_newlink+0xeb/0x699
[<ffffffff81a29246>] ? _raw_spin_unlock+0x28/0x33
[<ffffffff8143ed1e>] ? security_capable+0x18/0x1a
[<ffffffff8107da51>] ? ns_capable+0x4d/0x65
[<ffffffff817de5ce>] rtnetlink_rcv_msg+0x181/0x194
[<ffffffff817de407>] ? rtnl_lock+0x17/0x19
[<ffffffff817de407>] ? rtnl_lock+0x17/0x19
[<ffffffff817de44d>] ? __rtnl_unlock+0x17/0x17
[<ffffffff818327c6>] netlink_rcv_skb+0x4d/0x93
[<ffffffff817de42f>] rtnetlink_rcv+0x26/0x2d
[<ffffffff81830f18>] netlink_unicast+0xcb/0x150
[<ffffffff8183198e>] netlink_sendmsg+0x501/0x523
[<ffffffff8115cba9>] ? might_fault+0x59/0xa9
[<ffffffff817b5398>] ? copy_from_user+0x2a/0x2c
[<ffffffff817b7b74>] sock_sendmsg+0x34/0x3c
[<ffffffff817b7f6d>] ___sys_sendmsg+0x1b8/0x255
[<ffffffff8115c5eb>] ? handle_pte_fault+0xbd5/0xd4a
[<ffffffff8100a2b0>] ? native_sched_clock+0x35/0x37
[<ffffffff8109e94b>] ? sched_clock_local+0x12/0x72
[<ffffffff8109eb9c>] ? sched_clock_cpu+0x9e/0xb7
[<ffffffff810cadbf>] ? rcu_read_lock_held+0x3b/0x3d
[<ffffffff811ac1d8>] ? __fcheck_files+0x4c/0x58
[<ffffffff811ac946>] ? __fget_light+0x2d/0x52
[<ffffffff817b8adc>] __sys_sendmsg+0x42/0x60
[<ffffffff817b8b0c>] SyS_sendmsg+0x12/0x1c
[<ffffffff81a29e32>] system_call_fastpath+0x12/0x17
Fixes: e7ed828f10bd8 ("netlink: support setting devgroup parameters")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux()
struct dst_entry *dst = sk->sk_rx_dst;
if (dst)
dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie);
to code reading sk->sk_rx_dst twice, once for the test and once for
the argument of ip6_dst_check() (dst_check() is inline). This allows
ip6_dst_check() to be called with null first argument, causing a crash.
Protect sk->sk_rx_dst access by READ_ONCE() both in IPv4 and IPv6
TCP early demux code.
Fixes: 41063e9dd119 ("ipv4: Early TCP socket demux.")
Fixes: c7109986db3c ("ipv6: Early TCP socket demux")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firstly, handle zero length calls properly. Believe it or not there
are a few of these happening during early boot.
Next, we can't just drop to a memcpy() call in the forward copy case
where dst <= src. The reason is that the cache initializing stores
used in the Niagara memcpy() implementations can end up clearing out
cache lines before we've sourced their original contents completely.
For example, considering NG4memcpy, the main unrolled loop begins like
this:
load src + 0x00
load src + 0x08
load src + 0x10
load src + 0x18
load src + 0x20
store dst + 0x00
Assume dst is 64 byte aligned and let's say that dst is src - 8 for
this memcpy() call. That store at the end there is the one to the
first line in the cache line, thus clearing the whole line, which thus
clobbers "src + 0x28" before it even gets loaded.
To avoid this, just fall through to a simple copy only mildly
optimized for the case where src and dst are 8 byte aligned and the
length is a multiple of 8 as well. We could get fancy and call
GENmemcpy() but this is good enough for how this thing is actually
used.
Reported-by: David Ahern <david.ahern@oracle.com>
Reported-by: Bob Picco <bpicco@meloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
ip6tables extensions check for this flag to restrict match/target to a
given protocol. Without this flag set, SYNPROXY6 returns an error.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
|
|
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM43362 firmware falsely reports it is capable of providing
MBSS. As a result AP mode no longer works for this device. Therefor
disable MBSS in the driver for this chipset.
Cc: stable@vger.kernel.org # 3.19.y
Reported-by: Jorg Krause <jkrause@posteo.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If ->run() fails, it can either free the data structures it
allocated, or leave that task to ->free() which will be called
on failures.
However:
md.c calls ->free() even if ->private_data is NULL, which
causes problems in some personalities.
raid0.c frees the data, but doesn't clear ->private_data,
which will become a problem when we fix md.c
So better fix both these issues at once.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Fixes: 5aa61f427e4979be733e4847b9199ff9cc48a47e
URL: https://bugzilla.kernel.org/show_bug.cgi?id=94381
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an
error) introduced the clamping of msg_namelen when the unsigned value
was larger than sizeof(struct sockaddr_storage). This caused a
msg_namelen of -1 to be valid. The native code was subsequently fixed by
commit dbb490b96584 (net: socket: error on a negative msg_namelen).
In addition, the native code sets msg_namelen to 0 when msg_name is
NULL. This was done in commit (6a2a2b3ae075 net:socket: set msg_namelen
to 0 if msg_name is passed as NULL in msghdr struct from userland) and
subsequently updated by 08adb7dabd48 (fold verify_iovec() into
copy_msghdr_from_user()).
This patch brings the get_compat_msghdr() in line with
copy_msghdr_from_user().
Fixes: db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an error)
Cc: David S. Miller <davem@davemloft.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation doesn't zero out the pages allocated.
Honor the __GFP_ZERO flag and zero out if set.
Cc: <stable@vger.kernel.org> # v3.14+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_send_fin() does not account for the memory it allocates properly, so
sk_forward_alloc can be negative in cases where we've sent a FIN:
ss example output (ss -amn | grep -B1 f4294):
tcp FIN-WAIT-1 0 1 192.168.0.1:45520 192.0.2.1:8080
skmem:(r0,rb87380,t0,tb87380,f4294966016,w1280,o0,bl0)
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
init_mm isn't a normal mm: it has swapper_pg_dir as its pgd (which
contains kernel mappings) and is used as the active_mm for the idle
thread.
When restoring the pgd after an EFI call, we write current->active_mm
into TTBR0. If the current task is actually the idle thread (e.g. when
initialising the EFI RTC before entering userspace), then the TLB can
erroneously populate itself with junk global entries as a result of
speculative table walks.
When we do eventually return to userspace, the task can end up hitting
these junk mappings leading to lockups, corruption or crashes.
This patch fixes the problem in the same way as the CPU suspend code by
ensuring that we never switch to the init_mm in efi_set_pgd and instead
point TTBR0 at the zero page. A check is also added to cpu_switch_mm to
BUG if we get passed swapper_pg_dir.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: f3cdfd239da5 ("arm64/efi: move SetVirtualAddressMap() to UEFI stub")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
for throw routes to trigger evaluation of other policy rules
EAGAIN needs to be propagated up to fib_rules_lookup
similar to how its done for IPv4
A simple testcase for verification is:
ip -6 rule add lookup 33333 priority 33333
ip -6 route add throw 2001:db8::1
ip -6 route add 2001:db8::1 via fe80::1 dev wlan0 table 33333
ip route get 2001:db8::1
Signed-off-by: Steven Barth <cyrus@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matt Grant reported frequent crashes in ipv6_select_ident when
udp6_ufo_fragment is called from openvswitch on a skb that doesn't
have a dst_entry set.
ipv6_proxy_select_ident generates the frag_id without using the dst
associated with the skb. This approach was suggested by Vladislav
Yasevich.
Fixes: 0508c07f5e0c ("ipv6: Select fragment id during UFO segmentation if not set.")
Cc: Vladislav Yasevich <vyasevic@redhat.com>
Reported-by: Matt Grant <matt@mattgrant.net.nz>
Tested-by: Matt Grant <matt@mattgrant.net.nz>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b4b55cda5874 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda5874 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We have to check for IP6T_INV_PROTO in invflags, instead of flags.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Balazs Scheidler <bazsi@balabit.hu>
|
|
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdbf74a7d8fe0f0a44e85da1ed5975946
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
Nicolas Dichtel
Hariprasad Shenai
WANG Cong
Ben Hutchings
D.S. Ljungmark
Cliff Clark
Jack Morgenstein
Ido Shamay
Simon Horman
Michal Kubeček
Yuval Mintz
David S. Miller
Linus Torvalds
Pablo Neira Ayuso
Andreas Werner
Andri Yngvason
Stephane Grosjean
Colin Ian King
Ahmed S. Darwish
Larry Finger
Ondrej Zary
Arend van Spriel
NeilBrown
Al Viro
Catalin Marinas
Suzuki K. Poulose
Suresh Reddy
Vasundhara Volam
Josh Hunt
Will Deacon
Steven Barth
Markos Chandras
Sabrina Dubroca
Rafael J. Wysocki
Christophe Vu-Brugier
Nicholas Bellinger
Dan Carpenter
Bart Van Assche