| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The n_voltages setting is not set, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
mcp16502_suspend/resume_noirq is only used by SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
when CONFIG_PM_SLEEP is defined.
So use #ifdef CONFIG_PM_SLEEP instead CONFIG_SUSPEND guard.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch does the following:
- align parameter with parenthesis
- fix compile error
If CONFIG_SUSPEND is not set the dummy pm_ops
callbacks are named mcp16502_suspend and mcp16502_resume
instead of mcp16502_suspend_noirq and mcp16502_resume_noirq.
Excerpt from compile log (kbuild test robot):
In file included from include/linux/device.h:23:0,
from include/linux/gpio/driver.h:5,
from include/asm-generic/gpio.h:13,
from include/linux/gpio.h:62,
from drivers/regulator/mcp16502.c:11:
>> drivers/regulator/mcp16502.c:527:32: error: 'mcp16502_suspend_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend'?
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
>> drivers/regulator/mcp16502.c:528:10: error: 'mcp16502_resume_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend_noirq'?
mcp16502_resume_noirq)
vim +527 drivers/regulator/mcp16502.c
524
525 #ifdef CONFIG_PM
526 static const struct dev_pm_ops mcp16502_pm_ops = {
> 527 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
> 528 mcp16502_resume_noirq)
529 };
530 #endif
531 static const struct i2c_device_id mcp16502_i2c_id[] = {
532 { "mcp16502", 0 },
533 { }
534 };
535 MODULE_DEVICE_TABLE(i2c, mcp16502_i2c_id);
536
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes the following sparse warning:
drivers/regulator/act8945a-regulator.c:340:1: warning:
symbol 'act8945a_pm' was not declared. Should it be static?
Fixes: 7482d6ecc68e ("regulator: act8945a-regulator: Implement PM functionalities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix 'defined but not used' compiler warning for act8945a_suspend()
function in case CONFIG_PM_SLEEP is not defined.
Fixes: b5ebba46e694 ("regulator: act8945a-regulator: add shutdown function")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reported-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Initial commit of set_ramp_delay feature was missing an assignment which
should have populated slew_rate table for dcdc2 regulator. Add it.
Fixes: d29f54df8b16 ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support for entering/resuming suspend states.
It does this by setting the LPM pin of the PMIC.
When suspending the PMIC will enter the Low-power mode
when the LPM pin will be set to high. If the suspend target state
is suspend-to-mem, the PMIC will transition to Hibernate mode,
otherwise, if it is standby, it will remain in Low-power mode.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP20X_OFF define is an actual specific bit, define it as such.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the bitops.h header as we need it, alphabetize header order.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The OLinuXino Lime2 has a big capacitor on its LDO3 output. It is
actually too large, causing the PMIC to shutdown when toggling the LDO3.
By enabling soft-start and ramp delay we increase the time for the
capacitor to charge lowering the current drain on the power regulator.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, implement software-based 'regulator-soft-start'
property for AXP209 LDO3 regulator, which is used to first bring up
the LDO3 to the lowest possible voltage and then enable the LDO.
After that, we can set the requested voltage as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
come up slowly and staggered, potentially reducing overall inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3, therefore we can use the standard 'regulator-ramp-delay'
property for those 2 regulators.
Note that the voltage ramp only works when the regulator is already
enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current axp20x names the ramping register 'scal' which probably
means scaling. Since the register really has nothing to do with
scaling, but really is the voltage ramp we rename it appropriately.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds a maintainer for the MCP16502 PMIC
driver.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
Axel Lin
Andrei.Stefanescu@microchip.com
Wei Yongjun
Kangjie Lu
Claudiu Beznea
Priit Laes
Olliver Schinagl