| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Make sure the max_speed_hz of spi_device does not override
the max_speed_hz of controller.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201209173514.93328-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Let's set the 'use_gpio_descriptors' field so that we use the new way of
requesting the CS GPIOs in the core. This allows us to avoid having to
configure the CS pins in "output" mode with an 'output-enable' pinctrl
setting.
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201204193540.3047030-4-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is already handed by default in spi_setup() if the bits_per_word is
0, so just drop it to shave off a line.
Cc: Simon Glass <sjg@chromium.org>
Cc: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20201204193540.3047030-3-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There isn't any need to overwrite the mode here in the driver with what
has been detected by the firmware, such as DT or ACPI. In fact, if we
use the SPI CS gpio descriptor feature we will overwrite the mode with
SPI_MODE_0 where it already contains SPI_MODE_0 and more importantly
SPI_CS_HIGH. Clearing the SPI_CS_HIGH bit causes the CS line to toggle
when the device is probed when it shouldn't change, confusing the driver
and making it fail to probe. Drop the assignment and let the spi core
take care of it.
Fixes: a17d94f0b6e1 ("mfd: Add ChromeOS EC SPI driver")
Cc: Simon Glass <sjg@chromium.org>
Cc: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20201204193540.3047030-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Canaan Kendryte K210 RISC-V SoC includes a DW apb_ssi v4 controller
which is documented to have a 32 words deep TX and RX FIFO. The FIFO
length detection in spi_hw_init() correctly detects this value.
However, when the controller RX FIFO is filled up to 32 entries
(RXFLR = 32), an RX FIFO overrun error occurs. This likely due to a
hardware bug which can be avoided by force setting the fifo_len field of
struct dw_spi to 31.
Define the dw_spi_canaan_k210_init() function to force set fifo_len to
31 when the device node compatible string is "canaan,k210-spi".
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-4-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward
define a 32-bits maximum transfer size synthesis parameter
(SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration
(SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32,
the layout of the ctrlr0 register changes, moving the data frame format
field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size
can be up to 32-bits.
To support this new format, introduce the DW SPI capability flag
DW_SPI_CAP_DFS32 to indicate that a controller is configured with
SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis
parameter not accessible through a register, the detection of this
parameter value is done in spi_hw_init() by writing and reading the
ctrlr0 register and testing the value of bits [3..0]. These bits are
ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection.
If a DFS32 capable SPI controller is detected, the new field dfs_offset
in struct dw_spi is set to SPI_DFS32_OFFSET (16).
dw_spi_update_config() is modified to set the data frame size field at
the correct position is the CTRLR0 register, as indicated by the
dfs_offset field of the dw_spi structure.
The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave
controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI
capability flag set. However, for these ssi controllers, the dfs_offset
field is set to 0 as before (as per specifications).
Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag
set, dw_spi_add_host() extends the value of bits_per_word_mask from
16-bits to 32-bits. dw_reader() and dw_writer() are also modified to
handle 32-bits iTX/RX FIFO words.
Suggested-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the snps,dw-apb-ssi.yaml document to include the compatibility
string "canaan,k210-spi" compatible string for the Canaan Kendryte K210
RISC-V SoC DW apb_ssi V4 SPI controller.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-2-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add new compatible strings to the DT binding documents to support SiFive
FU740-C000.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/1607403341-57214-3-git-send-email-yash.shah@sifive.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
atmel_qspi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Piotr Bugalski <bugalski.piotr@gmail.com>
Link: https://lore.kernel.org/r/4b05c65cf6f1ea3251484fe9a00b4c65478a1ae3.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the call to devm_spi_register_master() fails on probe of the NPCM FIU
SPI driver, the clock "fiu->clk" is erroneously not unprepared and
disabled. Fix it.
Fixes: ace55c411b11 ("spi: npcm-fiu: add NPCM FIU controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.4+
Cc: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/9ae62f4e1cfe542bec57ac2743e6fca9f9548f55.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the call to devm_spi_register_controller() fails on probe of the
Qualcomm Atheros AR934x/QCA95xx SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Moreover, the controller's clock is enabled on probe but not disabled if
any of the subsequent probe steps fail.
Finally, there's an ordering issue in ar934x_spi_remove() wherein the
clock is disabled even though the controller is not yet unregistered.
It is unregistered after ar934x_spi_remove() by the devres framework.
As long as it is not unregistered, SPI transfers may still be ongoing
and disabling the clock may break them. It is not possible to use
devm_spi_register_controller() in this case, so move to the non-devm
variant.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 047980c582af ("spi: add driver for ar934x spi controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.7+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/1d58367d74d55741e0c2730a51a2b65012c8ab33.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the calls to device_reset() or devm_spi_register_controller() fail on
probe of the MediaTek MT7621 SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Additionally, there's an ordering issue in mt7621_spi_remove() wherein
the spi_controller is unregistered after disabling the SYS clock.
The correct order is to call spi_unregister_controller() *before* this
teardown step because bus accesses may still be ongoing until that
function returns.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 1ab7f2a43558 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.17+
Link: https://lore.kernel.org/r/72b680796149f5fcda0b3f530ffb7ee73b04f224.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 702b15cb9712 ("spi: mt7621: fix missing clk_disable_unprepare()
on error in mt7621_spi_probe") sought to disable the SYS clock on probe
errors, but only did so for 2 of 3 potentially failing calls: The clock
needs to be disabled on failure of devm_spi_register_controller() as
well.
Moreover, the commit purports to fix a bug in commit cbd66c626e16 ("spi:
mt7621: Move SPI driver out of staging") but in reality the bug has
existed since the driver was first introduced.
Fixes: 1ab7f2a43558 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.17+: 702b15cb9712: spi: mt7621: fix missing clk_disable_unprepare() on error in mt7621_spi_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/36ad42760087952fb7c10aae7d2628547c26a7ec.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the call to spi_register_master() fails on probe of the NetUP
Universal DVB driver, the spi_master struct is erroneously not freed.
Likewise, if spi_new_device() fails, the spi_controller struct is
not unregistered. Plug the leaks.
While at it, fix an ordering issue in netup_spi_release() wherein
spi_unregister_master() is called after fiddling with the IRQ control
register. The correct order is to call spi_unregister_master() *before*
this teardown step because bus accesses may still be ongoing until that
function returns.
Fixes: 52b1eaf4c59a ("[media] netup_unidvb: NetUP Universal DVB-S/S2/T/T2/C PCI-E card driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: <stable@vger.kernel.org> # v4.3+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.3+
Cc: Kozlov Sergey <serjk@netup.ru>
Link: https://lore.kernel.org/r/c4c24f333fc7840f4a3db24789e6e10dd660bede.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the call to devm_gpiod_get_optional() fails on probe of the NXP
SC18IS602/603 SPI driver, the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: f99008013e19 ("spi: sc18is602: Add reset control via gpio pin.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Phil Reid <preid@electromag.com.au>
Link: https://lore.kernel.org/r/d5f715527b894b91d530fe11a86f51b3184a4e1a.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the calls to devm_clk_get(), devm_spi_register_master() or
clk_prepare_enable() fail on probe of the Mikrotik RB4xx SPI driver,
the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 05aec357871f ("spi: Add SPI driver for Mikrotik RB4xx series boards")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.2+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Bert Vermeulen <bert@biot.com>
Link: https://lore.kernel.org/r/369bf26d71927f60943b1d9d8f51810f00b0237d.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the call to devm_spi_register_master() fails on probe of the GPIO SPI
driver, the spi_master struct is erroneously not freed:
After allocating the spi_master, its reference count is 1. The driver
unconditionally decrements the reference count on unbind using a devm
action. Before calling devm_spi_register_master(), the driver
unconditionally increments the reference count because on success,
that function will decrement the reference count on unbind. However on
failure, devm_spi_register_master() does *not* decrement the reference
count, so the spi_master is leaked.
The issue was introduced by commits 8b797490b4db ("spi: gpio: Make sure
spi_master_put() is called in every error path") and 79567c1a321e ("spi:
gpio: Use devm_spi_register_master()"), which sought to plug leaks
introduced by 9b00bc7b901f ("spi: spi-gpio: Rewrite to use GPIO
descriptors") but missed this remaining leak.
The situation was later aggravated by commit d3b0ffa1d75d ("spi: gpio:
prevent memory leak in spi_gpio_probe"), which introduced a
use-after-free because it releases a reference on the spi_master if
devm_add_action_or_reset() fails even though the function already
does that.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 9b00bc7b901f ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.1-: 8b797490b4db: spi: gpio: Make sure spi_master_put() is called in every error path
Cc: <stable@vger.kernel.org> # v5.1-: 45beec351998: spi: bitbang: Introduce spi_bitbang_init()
Cc: <stable@vger.kernel.org> # v5.1-: 79567c1a321e: spi: gpio: Use devm_spi_register_master()
Cc: <stable@vger.kernel.org> # v5.4-: d3b0ffa1d75d: spi: gpio: prevent memory leak in spi_gpio_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Link: https://lore.kernel.org/r/86eaed27431c3d709e3748eb76ceecbfc790dd37.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the call to devm_spi_register_controller() fails on probe of the
MediaTek SPI NOR driver, the spi_controller struct is erroneously not
freed.
Since commit a1daaa991ed1 ("spi: spi-mtk-nor: use dma_alloc_coherent()
for bounce buffer"), the same happens if the call to
dmam_alloc_coherent() fails.
Since commit 3bfd9103c7af ("spi: spi-mtk-nor: Add power management
support"), the same happens if the call to mtk_nor_enable_clk() fails.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 881d1ee9fe81 ("spi: add support for mediatek spi-nor controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ikjoon Jang <ikjn@chromium.org>
Cc: <stable@vger.kernel.org> # v5.7+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/d5b9f0289465394e73dedb8ec51e180a8f1dffc9.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the calls to devm_clk_get() or devm_ioremap_resource() fail on probe
of the Macronix SPI driver, the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: b942d80b0a39 ("spi: Add MXIC controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Mason Yang <masonccyang@mxic.com.tw>
Link: https://lore.kernel.org/r/4fa6857806e7e75741c05d057ac9df3564460114.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rpcif_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: eb8d6d464a27 ("spi: add Renesas RPC-IF driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.9+
Cc: Sergei Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/c5da472c28021da2f6517441685cef033d40b140.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pxa2xx_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master/slave() helper
which keeps the private data accessible until the driver has unbound.
Fixes: 32e5b57232c0 ("spi: pxa2xx: Fix controller unregister order")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v2.6.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v2.6.17+: 32e5b57232c0: spi: pxa2xx: Fix controller unregister order
Cc: <stable@vger.kernel.org> # v2.6.17+
Link: https://lore.kernel.org/r/5764b04d4a6e43069ebb7808f64c2f774ac6f193.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
spi_sh_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 680c1305e259 ("spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v3.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v3.0+
Cc: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/6d97628b536baf01d5e3e39db61108f84d44c8b2.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
qcom_qspi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: f79a158d37c2 ("spi: spi-qcom-qspi: Use OPP API to set clk/perf state")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.9+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/b6d3c4dce571d78a532fd74f27def0d5dc8d8a24.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
spi_geni_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Moreover, since commit 1a9e489e6128 ("spi: spi-geni-qcom: Use OPP API to
set clk/perf state"), spi_geni_probe() leaks the spi_master allocation
if the calls to dev_pm_opp_set_clkname() or dev_pm_opp_of_add_table()
fail.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.20+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.20+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Girish Mahadevan <girishm@codeaurora.org>
Link: https://lore.kernel.org/r/dfa1d8c41b8acdfad87ec8654cd124e6e3cb3f31.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
davinci_spi_remove() accesses the driver's private data after it's been
freed with spi_master_put().
Fix by moving the spi_master_put() to the end of the function.
Fixes: fe5fd2540947 ("spi: davinci: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: <stable@vger.kernel.org> # v4.7+
Link: https://lore.kernel.org/r/412f7eb1cf8990e0a3a2153f4c577298deab623e.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
QSPI_IFR is set as the last QSPI Instruction Frame register
regardless of the sama5d2 or sam9x60 version of the IP. Move
the writing of QSPI_IFR outside of the IP specific code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-5-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The address must be written in QSPI_IAR only when we have
a instruction frame with address but no data.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-4-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
That bit describes the APB transfer type. We are writing
serial memory registers via AHB acesses, that bit does not
make sense in the current context.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-3-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Following error was seen when mounting a 16MByte ubifs:
UBIFS error (ubi0:0 pid 1893): check_lpt_type.constprop.6: invalid type (15) in LPT node type
QSPI_IFR.TFRTYP was not set correctly. When data transfer is enabled
and one wants to access the serial memory through AHB in order to:
- read in the serial memory, but not a memory data, for example
a JEDEC-ID, QSPI_IFR.TFRTYP must be written to '0' (both sama5d2
and sam9x60).
- read in the serial memory, and particularly a memory data,
TFRTYP must be written to '1' (both sama5d2 and sam9x60).
- write in the serial memory, but not a memory data, for example
writing the configuration or the QSPI_SR, TFRTYP must be written
to '2' for sama5d2 and to '0' for sam9x60.
- write in the serial memory in particular to program a memory data,
TFRTYP must be written to '3' for sama5d2 and to '1' for sam9x60.
Fix the setting of the QSPI_IFR.TFRTYP field.
Fixes: 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Cc: <stable@vger.kernel.org> # v5.0+
Reported-by: Tom Burkart <tom@aussec.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-2-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: abf00907538e ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/1607071357-33378-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for LPSS SPI on Intel Alder Lake. It has four LPSS SPI
controllers each having two chip selects.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20201204082409.183700-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If cs-gpios property is used in devicetree then ctlr->num_chipselect value
may be changed by spi_get_gpio_descs().
So use ctlr->max_native_cs instead of ctlr->num_chipselect to set SPI_MCR
Fixes: 4fcc7c2292de (spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR)
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20201201085916.63543-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
broke the use of the SPISEL_BOOT signal as a chip select on the
MPC8309.
pdata->max_chipselect, which becomes master->num_chipselect, must be
initialized to take into account the possibility that there's one more
chip select in use than the number of GPIO chip selects.
Cc: stable@vger.kernel.org # v5.4+
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201127152947.376-1-rasmus.villemoes@prevas.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
When setting sk_err, set it to ee_errno, not ee_origin.
Commit f5f99309fa74 ("sock: do not set sk_err in
sock_dequeue_err_skb") disabled updating sk_err on errq dequeue,
which is correct for most error types (origins):
- sk->sk_err = err;
Commit 38b257938ac6 ("sock: reset sk_err when the error queue is
empty") reenabled the behavior for IMCP origins, which do require it:
+ if (icmp_next)
+ sk->sk_err = SKB_EXT_ERR(skb_next)->ee.ee_origin;
But read from ee_errno.
Fixes: 38b257938ac6 ("sock: reset sk_err when the error queue is empty")
Reported-by: Ayush Ranjan <ayushranjan@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20201126151220.2819322-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If an msk listener receives an MPJ carrying an invalid token, it
will zero the request socket msk entry. That should later
cause fallback and subflow reset - as per RFC - at
subflow_syn_recv_sock() time due to failing hmac validation.
Since commit 4cf8b7e48a09 ("subflow: introduce and use
mptcp_can_accept_new_subflow()"), we unconditionally dereference
- in mptcp_can_accept_new_subflow - the subflow request msk
before performing hmac validation. In the above scenario we
hit a NULL ptr dereference.
Address the issue doing the hmac validation earlier.
Fixes: 4cf8b7e48a09 ("subflow: introduce and use mptcp_can_accept_new_subflow()")
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Link: https://lore.kernel.org/r/03b2cfa3ac80d8fc18272edc6442a9ddf0b1e34e.1606400227.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the openvswitch module is not accepting the correctly formated
netlink message for the TTL decrement action. For both setting and getting
the dec_ttl action, the actions should be nested in the
OVS_DEC_TTL_ATTR_ACTION attribute as mentioned in the openvswitch.h uapi.
When the original patch was sent, it was tested with a private OVS userspace
implementation. This implementation was unfortunately not upstreamed and
reviewed, hence an erroneous version of this patch was sent out.
Leaving the patch as-is would cause problems as the kernel module could
interpret additional attributes as actions and vice-versa, due to the
actions not being encapsulated/nested within the actual attribute, but
being concatinated after it.
Fixes: 744676e77720 ("openvswitch: add TTL decrement action")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/160622121495.27296.888010441924340582.stgit@wsfd-netdev64.ntdv.lab.eng.bos.redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since some gcc generates a broken DWARF which lacks DW_AT_declaration
attribute from the subprogram DIE of function prototype.
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=97060)
So, in addition to the DW_AT_declaration check, we also check the
subprogram DIE has DW_AT_inline or actual entry pc.
Committer testing:
# cat /etc/fedora-release
Fedora release 33 (Thirty Three)
#
Before:
# perf test vfs_getname
78: Use vfs_getname probe to get syscall args filenames : FAILED!
79: Check open filename arg using perf trace + vfs_getname : FAILED!
81: Add vfs_getname probe to get syscall args filenames : FAILED!
#
After:
# perf test vfs_getname
78: Use vfs_getname probe to get syscall args filenames : Ok
79: Check open filename arg using perf trace + vfs_getname : Ok
81: Add vfs_getname probe to get syscall args filenames : Ok
#
Reported-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: http://lore.kernel.org/lkml/160645613571.2824037.7441351537890235895.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix die_entrypc() to return error correctly if the DIE has no
DW_AT_ranges attribute. Since dwarf_ranges() will treat the case as an
empty ranges and return 0, we have to check it by ourselves.
Fixes: 91e2f539eeda ("perf probe: Fix to show function entry line as probe-able")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: http://lore.kernel.org/lkml/160645612634.2824037.5284932731175079426.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently perf stat shows some metrics (like IPC) for defined events.
But when no aggregation mode is used (-A option), it shows incorrect
values since it used a value from a different cpu.
Before:
$ perf stat -aA -e cycles,instructions sleep 1
Performance counter stats for 'system wide':
CPU0 116,057,380 cycles
CPU1 86,084,722 cycles
CPU2 99,423,125 cycles
CPU3 98,272,994 cycles
CPU0 53,369,217 instructions # 0.46 insn per cycle
CPU1 33,378,058 instructions # 0.29 insn per cycle
CPU2 58,150,086 instructions # 0.50 insn per cycle
CPU3 40,029,703 instructions # 0.34 insn per cycle
1.001816971 seconds time elapsed
So the IPC for CPU1 should be 0.38 (= 33,378,058 / 86,084,722)
but it was 0.29 (= 33,378,058 / 116,057,380) and so on.
After:
$ perf stat -aA -e cycles,instructions sleep 1
Performance counter stats for 'system wide':
CPU0 109,621,384 cycles
CPU1 159,026,454 cycles
CPU2 99,460,366 cycles
CPU3 124,144,142 cycles
CPU0 44,396,706 instructions # 0.41 insn per cycle
CPU1 120,195,425 instructions # 0.76 insn per cycle
CPU2 44,763,978 instructions # 0.45 insn per cycle
CPU3 69,049,079 instructions # 0.56 insn per cycle
1.001910444 seconds time elapsed
Fixes: 44d49a600259 ("perf stat: Support metrics in --per-core/socket mode")
Reported-by: Sam Xi <xyzsam@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201127041404.390276-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
It didn't check the tool->cgroup_events bit which is set when the
--all-cgroups option is given. Without it, samples will not have cgroup
info so no reason to synthesize.
We can check the PERF_RECORD_CGROUP records after running perf record
*WITHOUT* the --all-cgroups option:
Before:
$ perf report -D | grep CGROUP
0 0 0x8430 [0x38]: PERF_RECORD_CGROUP cgroup: 1 /
CGROUP events: 1
CGROUP events: 0
CGROUP events: 0
After:
$ perf report -D | grep CGROUP
CGROUP events: 0
CGROUP events: 0
CGROUP events: 0
Committer testing:
Before:
# perf record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 2.208 MB perf.data (10003 samples) ]
# perf report -D | grep "CGROUP events"
CGROUP events: 146
CGROUP events: 0
CGROUP events: 0
#
After:
# perf record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 2.208 MB perf.data (10448 samples) ]
# perf report -D | grep "CGROUP events"
CGROUP events: 0
CGROUP events: 0
CGROUP events: 0
#
With all-cgroups:
# perf record --all-cgroups -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 2.374 MB perf.data (11526 samples) ]
# perf report -D | grep "CGROUP events"
CGROUP events: 146
CGROUP events: 0
CGROUP events: 0
#
Fixes: 8fb4b67939e16 ("perf record: Add --all-cgroups option")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201127054356.405481-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
An appropriate return value should be set on the failed path.
Fixes: 2a09a84c720b436a ("perf diff: Support hot streams comparison")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20201124103652.438-1-thunder.leizhen@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the changes in:
7a078d2d18801bba ("libbpf, hashmap: Fix undefined behavior in hash_bits")
That don't entail any changes in tools/perf.
This addresses this perf build warning:
Warning: Kernel ABI header at 'tools/perf/util/hashmap.h' differs from latest version at 'tools/lib/bpf/hashmap.h'
diff -u tools/perf/util/hashmap.h tools/lib/bpf/hashmap.h
Not a kernel ABI, its just that this uses the mechanism in place for
checking kernel ABI files drift.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently, if mce_end() fails, no_way_out - the variable denoting
whether the machine can recover from this MCE - is determined by whether
the worst severity that was found across the MCA banks associated with
the current CPU, is of panic severity.
However, at this point no_way_out could have been already set by
mca_start() after looking at all severities of all CPUs that entered the
MCE handler. If mce_end() fails, check first if no_way_out is already
set and, if so, stick to it, otherwise use the local worst value.
[ bp: Massage. ]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201127161819.3106432-2-gabriele.paoloni@intel.com
|
|
Commit 95fb5b0258b7 ("kvm: x86/mmu: Support MMIO in the TDP MMU") caused
the following WARNING on an Intel Ice Lake CPU:
get_mmio_spte: detect reserved bits on spte, addr 0xb80a0, dump hierarchy:
------ spte 0xb80a0 level 5.
------ spte 0xfcd210107 level 4.
------ spte 0x1004c40107 level 3.
------ spte 0x1004c41107 level 2.
------ spte 0x1db00000000b83b6 level 1.
WARNING: CPU: 109 PID: 10254 at arch/x86/kvm/mmu/mmu.c:3569 kvm_mmu_page_fault.cold.150+0x54/0x22f [kvm]
...
Call Trace:
? kvm_io_bus_get_first_dev+0x55/0x110 [kvm]
vcpu_enter_guest+0xaa1/0x16a0 [kvm]
? vmx_get_cs_db_l_bits+0x17/0x30 [kvm_intel]
? skip_emulated_instruction+0xaa/0x150 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xca/0x520 [kvm]
The guest triggering this crashes. Note, this happens with the traditional
MMU and EPT enabled, not with the newly introduced TDP MMU. Turns out,
there was a subtle change in the above mentioned commit. Previously,
walk_shadow_page_get_mmio_spte() was setting 'root' to 'iterator.level'
which is returned by shadow_walk_init() and this equals to
'vcpu->arch.mmu->shadow_root_level'. Now, get_mmio_spte() sets it to
'int root = vcpu->arch.mmu->root_level'.
The difference between 'root_level' and 'shadow_root_level' on CPUs
supporting 5-level page tables is that in some case we don't want to
use 5-level, in particular when 'cpuid_maxphyaddr(vcpu) <= 48'
kvm_mmu_get_tdp_level() returns '4'. In case upper layer is not used,
the corresponding SPTE will fail '__is_rsvd_bits_set()' check.
Revert to using 'shadow_root_level'.
Fixes: 95fb5b0258b7 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20201126110206.2118959-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
I mistakenly added the select attributes to the SPI_DW_BT1_DIRMAP config
instead of having them defined in SPI_DW_BT1. If the kernel doesn't have
the MULTIPLEXER and MUX_MMIO configs manually enabled and the
SPI_DW_BT1_DIRMAP config hasn't been selected, Baikal-T1 SPI device will
always fail to be probed by the driver. Fix that and the error reported by
the test robot:
>> ld.lld: error: undefined symbol: devm_mux_control_get
>>> referenced by spi-dw-bt1.c
>>> spi/spi-dw-bt1.o:(dw_spi_bt1_sys_init) in archive drivers/built-in.a
by moving the MULTIPLEXER/MUX_MMIO configs selection to the SPI_DW_BT1
config.
Link: https://lore.kernel.org/lkml/202011161745.uYRlekse-lkp@intel.com/
Link: https://lore.kernel.org/linux-spi/20201116040721.8001-1-rdunlap@infradead.org/
Fixes: abf00907538e ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201127144612.4204-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
kvm_cpu_accept_dm_intr and kvm_vcpu_ready_for_interrupt_injection are
a hodge-podge of conditions, hacked together to get something that
more or less works. But what is actually needed is much simpler;
in both cases the fundamental question is, do we have a place to stash
an interrupt if userspace does KVM_INTERRUPT?
In userspace irqchip mode, that is !vcpu->arch.interrupt.injected.
Currently kvm_event_needs_reinjection(vcpu) covers it, but it is
unnecessarily restrictive.
In split irqchip mode it's a bit more complicated, we need to check
kvm_apic_accept_pic_intr(vcpu) (the IRQ window exit is basically an INTACK
cycle and thus requires ExtINTs not to be masked) as well as
!pending_userspace_extint(vcpu). However, there is no need to
check kvm_event_needs_reinjection(vcpu), since split irqchip keeps
pending ExtINT state separate from event injection state, and checking
kvm_cpu_has_interrupt(vcpu) is wrong too since ExtINT has higher
priority than APIC interrupts. In fact the latter fixes a bug:
when userspace requests an IRQ window vmexit, an interrupt in the
local APIC can cause kvm_cpu_has_interrupt() to be true and thus
kvm_vcpu_ready_for_interrupt_injection() to return false. When this
happens, vcpu_run does not exit to userspace but the interrupt window
vmexits keep occurring. The VM loops without any hope of making progress.
Once we try to fix these with something like
return kvm_arch_interrupt_allowed(vcpu) &&
- !kvm_cpu_has_interrupt(vcpu) &&
- !kvm_event_needs_reinjection(vcpu) &&
- kvm_cpu_accept_dm_intr(vcpu);
+ (!lapic_in_kernel(vcpu)
+ ? !vcpu->arch.interrupt.injected
+ : (kvm_apic_accept_pic_intr(vcpu)
+ && !pending_userspace_extint(v)));
we realize two things. First, thanks to the previous patch the complex
conditional can reuse !kvm_cpu_has_extint(vcpu). Second, the interrupt
window request in vcpu_enter_guest()
bool req_int_win =
dm_request_for_irq_injection(vcpu) &&
kvm_cpu_accept_dm_intr(vcpu);
should be kept in sync with kvm_vcpu_ready_for_interrupt_injection():
it is unnecessary to ask the processor for an interrupt window
if we would not be able to return to userspace. Therefore,
kvm_cpu_accept_dm_intr(vcpu) is basically !kvm_cpu_has_extint(vcpu)
ANDed with the existing check for masked ExtINT. It all makes sense:
- we can accept an interrupt from userspace if there is a place
to stash it (and, for irqchip split, ExtINTs are not masked).
Interrupts from userspace _can_ be accepted even if right now
EFLAGS.IF=0.
- in order to tell userspace we will inject its interrupt ("IRQ
window open" i.e. kvm_vcpu_ready_for_interrupt_injection), both
KVM and the vCPU need to be ready to accept the interrupt.
... and this is what the patch implements.
Reported-by: David Woodhouse <dwmw@amazon.co.uk>
Analyzed-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Nikos Tsironis <ntsironis@arrikto.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Tested-by: David Woodhouse <dwmw@amazon.co.uk>
|
|
Centralize handling of interrupts from the userspace APIC
in kvm_cpu_has_extint and kvm_cpu_get_extint, since
userspace APIC interrupts are handled more or less the
same as ExtINTs are with split irqchip. This removes
duplicated code from kvm_cpu_has_injectable_intr and
kvm_cpu_has_interrupt, and makes the code more similar
between kvm_cpu_has_{extint,interrupt} on one side
and kvm_cpu_get_{extint,interrupt} on the other.
Cc: stable@vger.kernel.org
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Tested-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Device tree property is named typec-power-opmode, not power-opmode.
Fixes: da0cb6310094 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201127131735.28280-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Any record with a trailing newline (LOG_NEWLINE flag) cannot
be continued because the newline has been stripped and will
not be visible if the message is appended. This was already
handled correctly when committing in log_output() but was
not handled correctly when committing in log_store().
Fixes: f5f022e53b87 ("printk: reimplement log_cont using record extension")
Link: https://lore.kernel.org/r/20201126114836.14750-1-john.ogness@linutronix.de
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
Tudor Ambarus
Stephen Boyd
Damien Le Moal
Yash Shah
Lukas Wunner
Zhang Changzhong
Jarkko Nikula
Maxim Kochetkov
Rasmus Villemoes
Linus Torvalds
Willem de Bruijn
Paolo Abeni
Eelco Chaudron
Masami Hiramatsu
Namhyung Kim
Zhen Lei
Arnaldo Carvalho de Melo
Gabriele Paoloni
Vitaly Kuznetsov
Serge Semin
Paolo Bonzini
Amelie Delaunay
John Ogness