| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We were ignoring the FIF_ALLMULTI flag when setting the multicast
addresses with MCAST_FILTER_CMD. Check if this flag is set and enable
pass_all accordingly. We also need to set the count to 0 if pass_all
is enable so we don't pass addresses to the firmware when not needed
(as doing so causes an assert).
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196741
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The MCAST_FILTER_CMD can get quite large when we have many mcast
addresses to set (we support up to 255). So the command should be
send as NOCOPY to prevent a warning caused by too-long commands:
WARNING: CPU: 0 PID: 9700 at /root/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/pcie/tx.c:1550 iwl_pcie_enqueue_hcmd+0x8c7/0xb40 [iwlwifi]
Command MCAST_FILTER_CMD (0x1d0) is too large (328 bytes)
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196743
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
iwl_mvm_start_mac_queues() takes a bitmap of the queues to wake.
When deferred tx is purged, set the bit of the hw_queue so
the correct queue will be waken up.
Fixes: 7e39a00d5931 ("iwlwifi: mvm: start mac queues when deferred tx frames are purged")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add a new state to enum iwl_mvm_agg_state, which is used between
queueing the work that starts tx aggregations and actually starting that
work (changing to state IWL_AGG_STARTING).
This solves a race where ieee80211_start_tx_ba_session is called a
second time, before the work queued by the first run has a chance to
change the agg_state. In this case the second call to
ieee80211_start_tx_ba_session returns an error, and the fallback is to
abort the ba session start.
Fixes: 482e48440a0e ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
AP interfaces now send all non-bufferable frames using the broadcast
station. Thus allow them to use the probe queue and don't warn about
it.
Fixes: eb045e6e0389 ("iwlwifi: mvm: Avoid deferring non bufferable frames")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When starting wowlan mac80211 requests flush w/o vif
and we ignore this request. As a result some packets
stay stuck in the queue and it may end up with a queue
hang.
Allow the driver to flush queues even if station isn't
specified.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we set disconnect on wowlan and run suspend/resume, will run
into:
...snipped
iwlwifi 0000:01:00.0: Failed to load firmware chunk!
iwlwifi 0000:01:00.0: Could not load the [0] uCode section
iwlwifi 0000:01:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
It is because we still keep IWL_MVM_STATUS_IN_HW_RESTART in
__iwl_mvm_resume. When mac80211 starts the device as
__iwl_mvm_mac_start(), we will miss iwl_mvm_restart_cleanup(mvm).
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The LEDS_CMD command is only supported in some newer FW versions
(e.g. iwlwifi-8000C-31.ucode), so we can't send it to older versions
(such as iwlwifi-8000C-27.ucode).
To fix this, check for a new bit in the FW capabilities TLV that tells
when the command is supported.
Note that the current version of -31.ucode in linux-firmware.git
(31.532993.0) does not have this capability bit set, so the LED won't
work, even though this version should support it. But we will update
this firmware soon, so it won't be a problem anymore.
Fixes: 7089ae634c50 ("iwlwifi: mvm: use firmware LED command where applicable")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit 87d8a9f35202 ("rtlwifi: btcoex: call bind to setup btcoex"),
the code turns on a call to exhalbtc_bind_bt_coex_withadapter(). This
routine contains a bug that causes incorrect antenna selection for those
HP laptops with only one antenna and an incorrectly programmed EFUSE.
These boxes are the ones that need the ant_sel module parameter.
Fixes: 87d8a9f35202 ("rtlwifi: btcoex: call bind to setup btcoex")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.13+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit bcd37f4a0831 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when
hw initialisation done"), there is an additional error when the module
parameter ant_sel is used to select the auxilary antenna. The error is
that the antenna selection is not checked when writing the antenna
selection register.
Fixes: bcd37f4a0831 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.12+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The net device is already stored in the 'net' variable, so no need to call
dev_net() again.
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now there is no lock protecting nlk ngroups/groups' accessing in
netlink bind and getname. It's safe from nlk groups' setting in
netlink_release, but not from netlink_realloc_groups called by
netlink_setsockopt.
netlink_lock_table is needed in both netlink bind and getname when
accessing nlk groups.
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ChunYu found a netlink use-after-free issue by syzkaller:
[28448.842981] BUG: KASAN: use-after-free in __nla_put+0x37/0x40 at addr ffff8807185e2378
[28448.969918] Call Trace:
[...]
[28449.117207] __nla_put+0x37/0x40
[28449.132027] nla_put+0xf5/0x130
[28449.146261] sk_diag_fill.isra.4.constprop.5+0x5a0/0x750 [netlink_diag]
[28449.176608] __netlink_diag_dump+0x25a/0x700 [netlink_diag]
[28449.202215] netlink_diag_dump+0x176/0x240 [netlink_diag]
[28449.226834] netlink_dump+0x488/0xbb0
[28449.298014] __netlink_dump_start+0x4e8/0x760
[28449.317924] netlink_diag_handler_dump+0x261/0x340 [netlink_diag]
[28449.413414] sock_diag_rcv_msg+0x207/0x390
[28449.432409] netlink_rcv_skb+0x149/0x380
[28449.467647] sock_diag_rcv+0x2d/0x40
[28449.484362] netlink_unicast+0x562/0x7b0
[28449.564790] netlink_sendmsg+0xaa8/0xe60
[28449.661510] sock_sendmsg+0xcf/0x110
[28449.865631] __sys_sendmsg+0xf3/0x240
[28450.000964] SyS_sendmsg+0x32/0x50
[28450.016969] do_syscall_64+0x25c/0x6c0
[28450.154439] entry_SYSCALL64_slow_path+0x25/0x25
It was caused by no protection between nlk groups' free in netlink_release
and nlk groups' accessing in sk_diag_dump_groups. The similar issue also
exists in netlink_seq_show().
This patch is to defer nlk groups' free in deferred_put_nlk_sk.
Reported-by: ChunYu Wang <chunwang@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 520ac30f4551 ("net_sched: drop packets after root qdisc lock
is released) made a big change of tc for performance. There are two points
left in sch_prio and sch_qfq which are not changed with that commit. Now
enhance them now with __qdisc_drop.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The generic PHY 'phys' property sometime appears in the same node with
the Ethernet PHY 'phy' or 'phy-handle' properties. Add a warning in
phy-bindings.txt to reduce confusion.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.
Fixes: 7073f46e443e ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit
96a39aed25e6 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed25e6 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit 183db4 ("drivers: net: xgene: Correct probe sequence handling")
changed the return type of xgene_enet_check_phy_handle() to void.
This patch, removes the return statement from the last line.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes configuring tx/rx delay values for ACPI.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes reading tx/rx delay values for ACPI.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function calls to kcalloc use wrong parameter order and incorrect flags
values. GFP_KERNEL is used instead of flags now and the order is corrected.
The change was done using the following coccinelle script:
@@
expression E1,E2;
type T;
@@
-kcalloc(E1, E2, sizeof(T))
+kcalloc(E2, sizeof(T), GFP_KERNEL)
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bits in m_flags in struct rds_message are used for a plurality of
reasons, and from different contexts. To avoid any missing updates to
m_flags, use the atomic set_bit() instead of the non-atomic equivalent.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new TC IDR code uses GFP_KERNEL under spin lock. Which leads
to:
[ 582.621091] BUG: sleeping function called from invalid context at ../mm/slab.h:416
[ 582.629721] in_atomic(): 1, irqs_disabled(): 0, pid: 3379, name: tc
[ 582.636939] 2 locks held by tc/3379:
[ 582.641049] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff910354ce>] rtnetlink_rcv_msg+0x92e/0x1400
[ 582.650958] #1: (&(&tn->idrinfo->lock)->rlock){+.-.+.}, at: [<ffffffff9110a5e0>] tcf_idr_create+0x2f0/0x8e0
[ 582.662217] Preemption disabled at:
[ 582.662222] [<ffffffff9110a5e0>] tcf_idr_create+0x2f0/0x8e0
[ 582.672592] CPU: 9 PID: 3379 Comm: tc Tainted: G W 4.13.0-rc7-debug-00648-g43503a79b9f0 #287
[ 582.683432] Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.3.4 11/08/2016
[ 582.691937] Call Trace:
...
[ 582.742460] kmem_cache_alloc+0x286/0x540
[ 582.747055] radix_tree_node_alloc.constprop.6+0x4a/0x450
[ 582.753209] idr_get_free_cmn+0x627/0xf80
...
[ 582.815525] idr_alloc_cmn+0x1a8/0x270
...
[ 582.833804] tcf_idr_create+0x31b/0x8e0
...
Try to preallocate the memory with idr_prealloc(GFP_KERNEL)
(as suggested by Eric Dumazet), and change the allocation
flags under spin lock.
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We check tx avail through vhost_enable_notify() in the past which is
wrong since it only checks whether or not guest has filled more
available buffer since last avail idx synchronization which was just
done by vhost_vq_avail_empty() before. What we really want is checking
pending buffers in the avail ring. Fix this by calling
vhost_vq_avail_empty() instead.
This issue could be noticed by doing netperf TCP_RR benchmark as
client from guest (but not host). With this fix, TCP_RR from guest to
localhost restores from 1375.91 trans per sec to 55235.28 trans per
sec on my laptop (Intel(R) Core(TM) i7-5600U CPU @ 2.60GHz).
Fixes: 030881372460 ("vhost_net: basic polling support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdio_mux_init() use the parameter dev for two distinct thing:
1) Have a device for all devm_ functions
2) Get device_node from it
Since it is two distinct purpose, this patch add a parameter mdio_mux
that is linked to task 2.
This will also permit to register an of_node mdio-mux that lacks a direct
owning device.
For example a mdio-mux which is a subnode of a real device.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an RxRPC service packet comes in, the target connection is looked up
by an rb-tree search under RCU and a read-locked seqlock; the seqlock retry
check is, however, currently skipped if we got a match, but probably
shouldn't be in case the connection we found gets replaced whilst we're
doing a search.
Make the lookup procedure always go through need_seqretry(), even if the
lookup was successful. This makes sure we always pick up on a write-lock
event.
On the other hand, since we don't take a ref on the object, but rely on RCU
to prevent its destruction after dropping the seqlock, I'm not sure this is
necessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This code is no longer used, the logging function was changed by commit
fbca164776e4 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().
Fixes: fbca164776e4 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3ccd9e34f28e6ec677b812a860eb8eb ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPS_TX_INT_CAUSE[Bubble] is a normal condition for T6, hence
ignore this interrupt for T6.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPS_STAT_CTL[CountPauseStatTx] and MPS_STAT_CTL[CountPauseStatRx]
only control whether or not Pause Frames will be counted as part
of the 64-Byte Tx/Rx Frame counters. These bits do not control
whether Pause Frames are counted in the Total Tx/Rx Frames/Bytes
counters.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
do not reuse the loop counter which is used iterate over
the ports, so that sched_tbl will be freed for all the ports.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename "generic_xdp" to "skb_xdp" to avoid confusing it with the
generic XDP which will be done at netif_receive_skb().
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We reserve headroom unconditionally which could cause unnecessary
stress on socket memory accounting because of increased trusesize. Fix
this by only reserve extra headroom when XDP is set.
Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even though TC2QOS mapping is for switch egress queues, we need to
configure it correclty in order for the Broadcom tag ingress (CPU ->
switch) queue selection to work correctly since there is a 1:1 mapping
between switch egress queues and ingress queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch supports 8 egress queues per port, so indicate that such that
net/dsa/slave.c::dsa_slave_create can allocate the right number of TX queues.
While at it use SF2_NUM_EGRESS_QUEUE as a define for the number of queues we
support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We originally used skb->priority but that was not quite correct as this
bitfield needs to contain the egress switch queue we intend to send this
SKB to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let switch drivers indicate how many TX queues they support. Some
switches, such as Broadcom Starfighter 2 are designed with 8 egress
queues. Future changes will allow us to leverage the queue mapping and
direct the transmission towards a particular queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using ifdef in the C file.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In flow dissector there are no limits to the number of nested
encapsulations or headers that might be dissected which makes for a
nice DOS attack. This patch sets a limit of the number of headers
that flow dissector will parse.
Headers includes network layer headers, transport layer headers, shim
headers for encapsulation, IPv6 extension headers, etc. The limit for
maximum number of headers to parse has be set to fifteen to account for
a reasonable number of encapsulations, extension headers, VLAN,
in a packet. Note that this limit does not supercede the STOP_AT_*
flags which may stop processing before the headers limit is reached.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__skb_flow_dissect is riddled with gotos that make discerning the flow,
debugging, and extending the capability difficult. This patch
reorganizes things so that we only perform goto's after the two main
switch statements (no gotos within the cases now). It also eliminates
several goto labels so that there are only two labels that can be target
for goto.
Reported-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A header file cleanup apparently caused a build regression
with one driver using the knav infrastructure:
In file included from drivers/net/ethernet/ti/netcp_core.c:30:0:
include/linux/soc/ti/knav_dma.h:129:30: error: field 'direction' has incomplete type
enum dma_transfer_direction direction;
^~~~~~~~~
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_txpipe_open':
drivers/net/ethernet/ti/netcp_core.c:1349:21: error: 'DMA_MEM_TO_DEV' undeclared (first use in this function); did you mean 'DMA_MEMORY_MAP'?
config.direction = DMA_MEM_TO_DEV;
^~~~~~~~~~~~~~
DMA_MEMORY_MAP
drivers/net/ethernet/ti/netcp_core.c:1349:21: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_setup_navigator_resources':
drivers/net/ethernet/ti/netcp_core.c:1659:22: error: 'DMA_DEV_TO_MEM' undeclared (first use in this function); did you mean 'DMA_DESC_HOST'?
config.direction = DMA_DEV_TO_MEM;
As the header is no longer included implicitly through netdevice.h,
we should include it in the header that references the enum.
Fixes: 0dd5759dbb1c ("net: remove dmaengine.h inclusion from netdevice.h")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We get a new link error in allmodconfig kernels after ftgmac100
started using the ncsi helpers:
ERROR: "ncsi_vlan_rx_kill_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
ERROR: "ncsi_vlan_rx_add_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
Related to that, we get another error when CONFIG_NET_NCSI is disabled:
drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'?
drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'?
This fixes both problems at once, using a 'static inline' stub helper
for the disabled case, and exporting the functions when they are present.
Fixes: 51564585d8c6 ("ftgmac100: Support NCSI VLAN filtering when available")
Fixes: 21acf63013ed ("net/ncsi: Configure VLAN tag filter")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller reported crashes in bpf map creation or map update [1]
Problem is that nr_node_ids is a signed integer,
NUMA_NO_NODE is also an integer, so it is very tempting
to declare numa_node as a signed integer.
This means the typical test to validate a user provided value :
if (numa_node != NUMA_NO_NODE &&
(numa_node >= nr_node_ids ||
!node_online(numa_node)))
must be written :
if (numa_node != NUMA_NO_NODE &&
((unsigned int)numa_node >= nr_node_ids ||
!node_online(numa_node)))
[1]
kernel BUG at mm/slab.c:3256!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 2946 Comm: syzkaller916108 Not tainted 4.13.0-rc7+ #35
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801d2bc60c0 task.stack: ffff8801c0c90000
RIP: 0010:____cache_alloc_node+0x1d4/0x1e0 mm/slab.c:3292
RSP: 0018:ffff8801c0c97638 EFLAGS: 00010096
RAX: ffffffffffff8b7b RBX: 0000000001080220 RCX: 0000000000000000
RDX: 00000000ffff8b7b RSI: 0000000001080220 RDI: ffff8801dac00040
RBP: ffff8801c0c976c0 R08: 0000000000000000 R09: 0000000000000000
R10: ffff8801c0c97620 R11: 0000000000000001 R12: ffff8801dac00040
R13: ffff8801dac00040 R14: 0000000000000000 R15: 00000000ffff8b7b
FS: 0000000002119940(0000) GS:ffff8801db200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020001fec CR3: 00000001d2980000 CR4: 00000000001406f0
Call Trace:
__do_kmalloc_node mm/slab.c:3688 [inline]
__kmalloc_node+0x33/0x70 mm/slab.c:3696
kmalloc_node include/linux/slab.h:535 [inline]
alloc_htab_elem+0x2a8/0x480 kernel/bpf/hashtab.c:740
htab_map_update_elem+0x740/0xb80 kernel/bpf/hashtab.c:820
map_update_elem kernel/bpf/syscall.c:587 [inline]
SYSC_bpf kernel/bpf/syscall.c:1468 [inline]
SyS_bpf+0x20c5/0x4c40 kernel/bpf/syscall.c:1443
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x440409
RSP: 002b:00007ffd1f1792b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000141
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440409
RDX: 0000000000000020 RSI: 0000000020006000 RDI: 0000000000000002
RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000401d70
R13: 0000000000401e00 R14: 0000000000000000 R15: 0000000000000000
Code: 83 c2 01 89 50 18 4c 03 70 08 e8 38 f4 ff ff 4d 85 f6 0f 85 3e ff ff ff 44 89 fe 4c 89 ef e8 94 fb ff ff 49 89 c6 e9 2b ff ff ff <0f> 0b 0f 0b 0f 0b 66 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41
RIP: ____cache_alloc_node+0x1d4/0x1e0 mm/slab.c:3292 RSP: ffff8801c0c97638
---[ end trace d745f355da2e33ce ]---
Kernel panic - not syncing: Fatal exception
Fixes: 96eabe7a40aa ("bpf: Allow selecting numa node during map creation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 00fc0e0dda62 ("alpha: move exports to actual definitions") also
removed the exports of the math emulator hooks, which are defined in C
code. In case anyone cares about the option of CONFIG_MATHEMU=m, add
exports next to those definitions. Also add a MODULE_LICENSE.
Fixes: 00fc0e0dda62 ("alpha: move exports to actual definitions")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
Luca Coelho
Avraham Stern
Naftali Goldstein
David Spinadel
Matt Chen
Larry Finger
Kleber Sacilotto de Souza
Xin Long
Gao Feng
Baruch Siach
Jacob Keller
Anjali Singhai Jain
Iyappan Subramanian
Quan Nguyen
Zahari Doychev
Håkon Bugge
Jakub Kicinski
Jason Wang
Corentin Labbe
David Howells
Romain Perier
Claudiu Manoil
Ganesh Goudar
Florian Fainelli
Ido Schimmel
Thomas Meyer
Tom Herbert
Arnd Bergmann
Eric Dumazet
Ben Hutchings