aboutsummaryrefslogtreecommitdiffstats
path: root/tools/perf/scripts/python/export-to-postgresql.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2019-07-03serial: sh-sci: Terminate TX DMA during buffer flushingGeert Uytterhoeven1-2/+9
While the .flush_buffer() callback clears sci_port.tx_dma_len since commit 1cf4a7efdc71cab8 ("serial: sh-sci: Fix race condition causing garbage during shutdown"), it does not terminate a transmit DMA operation that may be in progress. Fix this by terminating any pending DMA operations, and resetting the corresponding cookie. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com> Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com> Link: https://lore.kernel.org/r/20190624123540.20629-3-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-03serial: sh-sci: Fix TX DMA buffer flushing and workqueue racesGeert Uytterhoeven1-7/+15
When uart_flush_buffer() is called, the .flush_buffer() callback zeroes the tx_dma_len field. This may race with the work queue function handling transmit DMA requests: 1. If the buffer is flushed before the first DMA API call, dmaengine_prep_slave_single() may be called with a zero length, causing the DMA request to never complete, leading to messages like: rcar-dmac e7300000.dma-controller: Channel Address Error happen and, with debug enabled: sh-sci e6e88000.serial: sci_dma_tx_work_fn: ffff800639b55000: 0...0, cookie 126 and DMA timeouts. 2. If the buffer is flushed after the first DMA API call, but before the second, dma_sync_single_for_device() may be called with a zero length, causing the transmit data not to be flushed to RAM, and leading to stale data being output. Fix this by: 1. Letting sci_dma_tx_work_fn() return immediately if the transmit buffer is empty, 2. Extending the critical section to cover all DMA preparational work, so tx_dma_len stays consistent for all of it, 3. Using local copies of circ_buf.head and circ_buf.tail, to make sure they match the actual operation above. Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com> Suggested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com> Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com> Link: https://lore.kernel.org/r/20190624123540.20629-2-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-03serial: mpsc: Remove obsolete MPSC driverMark Greer6-2202/+3
Support for the Marvell MV64x60 line of bridge chips that contained MPSC controllers has been removed and there are no other components that have that controller so remove its driver. Signed-off-by: Mark Greer <mgreer@animalcreek.com> Link: https://lore.kernel.org/r/20190626160553.28518-1-mgreer@animalcreek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-03serial: 8250: 8250_core: Fix missing unlock on error in serial8250_register_8250_port()Wei Yongjun1-2/+5
Add the missing unlock before return from function serial8250_register_8250_port() in the error handling case. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20190703055908.141294-1-weiyongjun1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21serial: stm32: add RX and TX FIFO flushErwan Le Ray1-5/+15
Adds a flush of RX and TX FIFOs, and fixes some errors: - adds RX FIFO flush in startup fonction - removes the useless transmitter enabling in startup fonction (e.g. receiver only, see Documentation/serial/driver) - configures FIFO threshold before enabling it, rather than after - flushes both TX and RX in set_termios function Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21serial: stm32: add support of RX FIFO thresholdErwan Le Ray2-3/+25
Adds the support of RX FIFO threshold in order to improve the RX FIFO management. This is done by enabling fifo threshold interrupt, instead of relying on rx empty/fifo not full irq. That basically generates one irq/char currently. With this patch: - RXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth FIFO) - irq rate may be reduced by up to 1/RXCFG, e.g. 1 over 8 with current RXCFG setting. - Receiver timeout is used to gather chars when FIFO threshold isn't reached. Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21serial: stm32: add support of TX FIFO thresholdErwan Le Ray2-9/+55
Adds the support of TX FIFO threshold in order to improve the TX FIFO management: - TX FIFO threshold irq enabling (instead of relying on tx empty / fifo not full irq that generates one irq/char) - TXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth FIFO) - irq rate may be reduced by up to 1/TXCFG, e.g. 1 over 8 with current TXCFG setting. Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21serial: stm32: update PIO transmissionErwan Le Ray1-14/+13
Improves PIO transmission: - Replaces the FIFO filling per character by a filling per blocks of characters, which provides better performances - Replaces the active waiting loop by TX empty interrupt dynamic handling. TXE interrupt is now enabled when data has to be sent (ie when uart_circ is not empty), and inhibited when there is no more data to send (ie when uart_circ is empty). Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21serial: stm32: add support of timeout interrupt for RXErwan Le Ray2-6/+26
Add support of RX timeout interrupts to limit the number of interrupts. RX timeout is a number of bits (baud clock cycles) without transmission seen in the receiver. One character is used as an arbitrary RX timeout value. If parity is enabled, the number of bits has to include parity bit. Signed-off-by: Gerald Baeza <gerald.baeza@st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"Oliver Barta1-2/+1
This reverts commit 2e9fe539108320820016f78ca7704a7342788380. Reading LSR unconditionally but processing the error flags only if UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission error information on UARTs where the transmission error flags are cleared by a read of LSR. Information are lost in case an error is detected right before the read of LSR while processing e.g. an UART_IIR_THRI interrupt. Signed-off-by: Oliver Barta <o.barta89@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Fixes: 2e9fe5391083 ("serial: 8250: Don't service RX FIFO if interrupts are disabled") Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21tty/serial/8250: use mctrl_gpio helpersYegor Yefremov7-15/+81
This patch permits the usage for GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI signals. Changed by Stefan: Only call mctrl_gpio_init(), if the device has no ACPI companion device to not break existing ACPI based systems. Also only use the mctrl_gpio_ functions when "gpios" is available. Use MSR / MCR <-> TIOCM wrapper functions. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Yegor Yefremov <yegorslists@googlemail.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Giulio Benetti <giulio.benetti@micronovasrl.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-21serial: mctrl_gpio: Check if GPIO property exisits before requesting itStefan Roese1-0/+14
This patch adds a check for the GPIOs property existence, before the GPIO is requested. This fixes an issue seen when the 8250 mctrl_gpio support is added (2nd patch in this patch series) on x86 platforms using ACPI. Here Mika's comments from 2016-08-09: " I noticed that with v4.8-rc1 serial console of some of our Broxton systems does not work properly anymore. I'm able to see output but input does not work. I bisected it down to commit 4ef03d328769eddbfeca1f1c958fdb181a69c341 ("tty/serial/8250: use mctrl_gpio helpers"). The reason why it fails is that in ACPI we do not have names for GPIOs (except when _DSD is used) so we use the "idx" to index into _CRS GPIO resources. Now mctrl_gpio_init_noauto() goes through a list of GPIOs calling devm_gpiod_get_index_optional() passing "idx" of 0 for each. The UART device in Broxton has following (simplified) ACPI description: Device (URT4) { ... Name (_CRS, ResourceTemplate () { GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly, "\\_SB.GPO0", 0x00, ResourceConsumer) { 0x003A } GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly, "\\_SB.GPO0", 0x00, ResourceConsumer) { 0x003D } }) In this case it finds the first GPIO (0x003A which happens to be RX pin for that UART), turns it into GPIO which then breaks input for the UART device. This also breaks systems with bluetooth connected to UART (those typically have some GPIOs in their _CRS). Any ideas how to fix this? We cannot just drop the _CRS index lookup fallback because that would break many existing machines out there so maybe we can limit this to only DT enabled machines. Or alternatively probe if the property first exists before trying to acquire the GPIOs (using device_property_present()). " This patch implements the fix suggested by Mika in his statement above. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Yegor Yefremov <yegorslists@googlemail.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Giulio Benetti <giulio.benetti@micronovasrl.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: 8250: pericom_do_set_divisor can be statickbuild test robot1-1/+1
Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips") Signed-off-by: kbuild test robot <lkp@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18tty: serial_core: Set port active bit in uart_port_activateSerge Semin1-1/+6
A bug was introduced by commit b3b576461864 ("tty: serial_core: convert uart_open to use tty_port_open"). It caused a constant warning printed into the system log regarding the tty and port counter mismatch: [ 21.644197] ttyS ttySx: tty_port_close_start: tty->count = 1 port count = 2 in case if session hangup was detected so the warning is printed starting from the second open-close iteration. Particularly the problem was discovered in situation when there is a serial tty device without hardware back-end being setup. It is considered by the tty-serial subsystems as a hardware problem with session hang up. In this case uart_startup() will return a positive value with TTY_IO_ERROR flag set in corresponding tty_struct instance. The same value will get passed to be returned from the activate() callback and then being returned from tty_port_open(). But since in this case tty_port_block_til_ready() isn't called the TTY_PORT_ACTIVE flag isn't set (while the method had been called before tty_port_open conversion was introduced and the rest of the subsystem code expected the bit being set in this case), which prevents the uart_hangup() method to perform any cleanups including the tty port counter setting to zero. So the next attempt to open/close the tty device will discover the counters mismatch. In order to fix the problem we need to manually set the TTY_PORT_ACTIVE flag in case if uart_startup() returned a positive value. In this case the hang up procedure will perform a full set of cleanup actions including the port ref-counter resetting. Fixes: b3b576461864 "tty: serial_core: convert uart_open to use tty_port_open" Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: 8250: Add MSR/MCR TIOCM conversion wrapper functionsStefan Roese2-22/+57
This patch adds wrapper functions to convert MSR <-> TIOCM and also MCR <-> TIOCM. These functions are used now in serial8250_do_set_mctrl() and serial8250_do_get_mctrl(). Signed-off-by: Stefan Roese <sr@denx.de> Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Giulio Benetti <giulio.benetti@micronovasrl.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: 8250: factor out serial8250_{set,clear}_THRI() helpersAndy Shevchenko4-27/+26
Factor out similar code pieces that set or clear UART_IER_THRI bit to serial8250_{set,clear}_THRI() helpers. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: fsl_lpuart: Remove unneeded OOM error messageFabio Estevam1-3/+1
There is no need to add an out-of-memory error message inside the driver because the core MM code will take care of it. Remove the unneeded OOM error message. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: uartps: Remove useless return from cdns_uart_poll_put_charNava kishore Manne1-2/+0
There is no reason to call return at the end of function which should return void. The patch is also remove one checkpatch warning: WARNING: void function return statements are not generally useful + return; +} Fixes: 6ee04c6c5488 ("tty: xuartps: Add polled mode support for xuartps") Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: uartps: Do not add a trailing semicolon to macroNava kishore Manne1-1/+1
This patch fixes this checkpatch warning: WARNING: macros should not use a trailing semicolon +#define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \ + clk_rate_change_nb); Fixes: d9bb3fb12685 ("tty: xuartps: Rebrand driver as Cadence UART") Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: uartps: Fix long line over 80 charsNava kishore Manne1-1/+2
Trivial patch which fixes one checkpatch warning: WARNING: line over 80 characters + !(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXFULL)) { Fixes: c8dbdc842d30 ("serial: xuartps: Rewrite the interrupt handling logic") Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: uartps: Fix multiple line dereferenceNava kishore Manne1-2/+2
Trivial patch which fixes this checkpatch warning: WARNING: Avoid multiple line dereference - prefer 'port->state->xmit.tail' + port->state->xmit.buf[port->state->xmit. + tail], port->membase + CDNS_UART_FIFO); Fixes: c8dbdc842d30 ("serial: xuartps: Rewrite the interrupt handling logic") Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: uartps: Use octal permission for module_param()Nava kishore Manne1-2/+2
Octal permission is preffered compare to symbolic one. This patch fixes checkpatch warnings: Symbolic permissions 'S_IRUGO' are not preferred. Consider using octal permissions '0444'. Fixes: 85baf542d54e ("tty: xuartps: support 64 byte FIFO size") Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: uartps: Use the same dynamic major number for all portsShubhrajyoti Datta1-2/+3
Let kernel to find out major number dynamically for the first device and then reuse it for other instances. This fixes the issue that each uart is registered with a different major number. After the patch: crw------- 1 root root 253, 0 Jun 10 08:31 /dev/ttyPS0 crw--w---- 1 root root 253, 1 Jan 1 1970 /dev/ttyPS1 Fixes: 024ca329bfb9 ("serial: uartps: Register own uart console and driver structures") Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: 8250: Add support for higher baud rates to Pericom chipsJay Dolan1-18/+79
The Pericom chips can achieve additional baud rates by programming the sample clock register. The baud rates can be described as 921600 * 16 / (16 - scr) for scr values 5 to 15. The divisor is set to 1 for these baud rates. Adds new quirk for Pericom chips other than the four port chips to use the Signed-off-by: Jay Dolan <jay.dolan@accesio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: imx: fix locking in set_termios()Sergey Organov1-10/+13
imx_uart_set_termios() called imx_uart_rts_active(), or imx_uart_rts_inactive() before taking port->port.lock. As a consequence, sport->port.mctrl that these functions modify could have been changed without holding port->port.lock. Moved locking of port->port.lock above the calls to fix the issue. Signed-off-by: Sergey Organov <sorganov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-13Revert "serial: stm32: select pinctrl state in each suspend/resume function"Greg Kroah-Hartman1-4/+0
This reverts commit c70669ecef4e34af8913108fae4b8a9b1dc63fa1 as it breaks the build. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: kbuild test robot <lkp@intel.com> Cc: Bich Hemon <bich.hemon@st.com> Cc: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10tty: serial: msm_serial: avoid system lockup conditionJorge Ramirez-Ortiz1-0/+4
The function msm_wait_for_xmitr can be taken with interrupts disabled. In order to avoid a potential system lockup - demonstrated under stress testing conditions on SoC QCS404/5 - make sure we wait for a bounded amount of time. Tested on SoC QCS404. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: 8250: Fix TX interrupt handling conditionRautkoski Kimmo EXT1-1/+2
Interrupt handler checked THRE bit (transmitter holding register empty) in LSR to detect if TX fifo is empty. In case when there is only receive interrupts the TX handling got called because THRE bit in LSR is set when there is no transmission (FIFO empty). TX handling caused TX stop, which in RS-485 half-duplex mode actually resets receiver FIFO. This is not desired during reception because of possible data loss. The fix is to check if THRI is set in IER in addition of the TX fifo status. THRI in IER is set when TX is started and cleared when TX is stopped. This ensures that TX handling is only called when there is really transmission on going and an interrupt for THRE and not when there are only RX interrupts. Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: stm32: fix a recursive locking in stm32_config_rs485Borut Seljak1-3/+0
Remove spin_lock_irqsave in stm32_config_rs485, it cause recursive locking. Already locked in uart_set_rs485_config. Fixes: 1bcda09d291081 ("serial: stm32: add support for RS485 hardware control mode") Signed-off-by: Borut Seljak <borut.seljak@t-2.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10tty: serial: 8250-of: Do not warn on deferred probeThierry Reding1-2/+3
Deferred probe is an expected return value for clk_get() on many platforms. The driver deals with it properly, so there's no need to output a warning that may potentially confuse users. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: imx: Use dev_info() instead of pr_info()Fabio Estevam1-1/+1
dev_info() is more appropriate for printing messages inside drivers, so switch to dev_info(). Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: fsl_lpuart: Use dev_info() instead of printk()Fabio Estevam1-2/+2
dev_info() is more appropriate for printing messages inside drivers, so switch to dev_info(). Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10uart: mediatek: support Rx in-band wakeupClaire Chang1-0/+24
In order to support Rx in-band wakeup, we need to enable irq wake on an edge sensitive interrupt of Rx pin before suspend and disable it when resuming. This interrupt is used only as wake source to resume the system when suspended. Note that the sent character will be lost as the controller is actually suspended. We use this to support wakeup on bluetooth. Bluetooth will repeatedly send 0xFD to wakeup host. Once host detects Rx falling, an interrupt is triggered, and the system leaves sleep state. Then, the bluetooth driver will send 0xFC to bluetooth and bluetooth can start to send normal HCI packets. Signed-off-by: Claire Chang <tientzu@chromium.org> Reviewed-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: uartps: Add a timeout to the tx empty waitShubhrajyoti Datta1-4/+10
In case the cable is not connected then the target gets into an infinite wait for tx empty. Add a timeout to the tx empty wait. Reported-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: uartps: Move the spinlock after the read of the tx emptyShubhrajyoti Datta1-2/+1
Currently we are doing a read of the status register. Move the spinlock after that as the reads need not be spinlock protected. This patch prevents relaxing the cpu with spinlock held. Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: 8250-mtk: modify uart DMA rxLong Cheng1-29/+20
Modify uart rx and complete for DMA Signed-off-by: Long Cheng <long.cheng@mediatek.com> Reviewed-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10tty/serial: digicolor: Fix digicolor-usart already registered warningKefeng Wang1-1/+5
When modprobe/rmmod/modprobe module, if platform_driver_register() fails, the kernel complained, proc_dir_entry 'driver/digicolor-usart' already registered WARNING: CPU: 1 PID: 5636 at fs/proc/generic.c:360 proc_register+0x19d/0x270 Fix this by adding uart_unregister_driver() when platform_driver_register() fails. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: stm32: Make stm32_get_databits staticYueHaibing1-1/+1
Fix sparse warning: drivers/tty/serial/stm32-usart.c:603:14: warning: symbol 'stm32_get_databits' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: stm32: select pinctrl state in each suspend/resume functionBich Hemon1-0/+4
Select either pinctrl sleep state in suspend function or default state in resume function. Signed-off-by: Bich Hemon <bich.hemon@st.com> Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-04Revert "consolemap: Fix a memory leaking bug in drivers/tty/vt/consolemap.c"Ben Hutchings1-5/+1
This reverts commit 84ecc2f6eb1cb12e6d44818f94fa49b50f06e6ac. con_insert_unipair() is working with a sparse 3-dimensional array: - p->uni_pgdir[] is the top layer - p1 points to a middle layer - p2 points to a bottom layer If it needs to allocate a new middle layer, and then fails to allocate a new bottom layer, it would previously free only p2, and now it frees both p1 and p2. But since the new middle layer was already registered in the top layer, it was not leaked. However, if it looks up an *existing* middle layer and then fails to allocate a bottom layer, it now frees both p1 and p2 but does *not* free any other bottom layers under p1. So it *introduces* a memory leak. The error path also cleared the wrong index in p->uni_pgdir[], introducing a use-after-free. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 84ecc2f6eb1c ("consolemap: Fix a memory leaking bug in drivers/tty/vt/consolemap.c") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-02Linux 5.2-rc3Linus Torvalds1-1/+1
2019-06-01mm, compaction: make sure we isolate a valid PFNSuzuki K Poulose1-1/+1
When we have holes in a normal memory zone, we could endup having cached_migrate_pfns which may not necessarily be valid, under heavy memory pressure with swapping enabled ( via __reset_isolation_suitable(), triggered by kswapd). Later if we fail to find a page via fast_isolate_freepages(), we may end up using the migrate_pfn we started the search with, as valid page. This could lead to accessing NULL pointer derefernces like below, due to an invalid mem_section pointer. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 [47/1825] Mem abort info: ESR = 0x96000004 Exception class = DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp = 0000000082f94ae9 [0000000000000008] pgd=0000000000000000 Internal error: Oops: 96000004 [#1] SMP ... CPU: 10 PID: 6080 Comm: qemu-system-aar Not tainted 510-rc1+ #6 Hardware name: AmpereComputing(R) OSPREY EV-883832-X3-0001/OSPREY, BIOS 4819 09/25/2018 pstate: 60000005 (nZCv daif -PAN -UAO) pc : set_pfnblock_flags_mask+0x58/0xe8 lr : compaction_alloc+0x300/0x950 [...] Process qemu-system-aar (pid: 6080, stack limit = 0x0000000095070da5) Call trace: set_pfnblock_flags_mask+0x58/0xe8 compaction_alloc+0x300/0x950 migrate_pages+0x1a4/0xbb0 compact_zone+0x750/0xde8 compact_zone_order+0xd8/0x118 try_to_compact_pages+0xb4/0x290 __alloc_pages_direct_compact+0x84/0x1e0 __alloc_pages_nodemask+0x5e0/0xe18 alloc_pages_vma+0x1cc/0x210 do_huge_pmd_anonymous_page+0x108/0x7c8 __handle_mm_fault+0xdd4/0x1190 handle_mm_fault+0x114/0x1c0 __get_user_pages+0x198/0x3c0 get_user_pages_unlocked+0xb4/0x1d8 __gfn_to_pfn_memslot+0x12c/0x3b8 gfn_to_pfn_prot+0x4c/0x60 kvm_handle_guest_abort+0x4b0/0xcd8 handle_exit+0x140/0x1b8 kvm_arch_vcpu_ioctl_run+0x260/0x768 kvm_vcpu_ioctl+0x490/0x898 do_vfs_ioctl+0xc4/0x898 ksys_ioctl+0x8c/0xa0 __arm64_sys_ioctl+0x28/0x38 el0_svc_common+0x74/0x118 el0_svc_handler+0x38/0x78 el0_svc+0x8/0xc Code: f8607840 f100001f 8b011401 9a801020 (f9400400) ---[ end trace af6a35219325a9b6 ]--- The issue was reported on an arm64 server with 128GB with holes in the zone (e.g, [32GB@4GB, 96GB@544GB]), with a swap device enabled, while running 100 KVM guest instances. This patch fixes the issue by ensuring that the page belongs to a valid PFN when we fallback to using the lower limit of the scan range upon failure in fast_isolate_freepages(). Link: http://lkml.kernel.org/r/1558711908-15688-1-git-send-email-suzuki.poulose@arm.com Fixes: 5a811889de10f1eb ("mm, compaction: use free lists to quickly locate a migration target") Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reported-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Mel Gorman <mgorman@techsingularity.net> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Qian Cai <cai@lca.pw> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01include/linux/generic-radix-tree.h: fix kerneldoc commentJonathan Corbet1-1/+1
The DOC comment block section in include/linux/generic-radix-tree.h contained a spurious colon, causing this warning in the documentation build: include/linux/generic-radix-tree.h:1: warning: no structured comments found Remove the colon and make the docs build happy. Link: http://lkml.kernel.org/r/20190524141933.74ae9050@lwn.net Signed-off-by: Jonathan Corbet <corbet@lwn.net> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Kent Overstreet <kent.overstreet@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01kernel/signal.c: trace_signal_deliver when signal_group_exitZhenliang Wei1-0/+2
In the fixes commit, removing SIGKILL from each thread signal mask and executing "goto fatal" directly will skip the call to "trace_signal_deliver". At this point, the delivery tracking of the SIGKILL signal will be inaccurate. Therefore, we need to add trace_signal_deliver before "goto fatal" after executing sigdelset. Note: SEND_SIG_NOINFO matches the fact that SIGKILL doesn't have any info. Link: http://lkml.kernel.org/r/20190425025812.91424-1-weizhenliang@huawei.com Fixes: cf43a757fd4944 ("signal: Restore the stop PTRACE_EVENT_EXIT") Signed-off-by: Zhenliang Wei <weizhenliang@huawei.com> Reviewed-by: Christian Brauner <christian@brauner.io> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Ivan Delalande <colona@arista.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Deepa Dinamani <deepa.kernel@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01drivers/iommu/intel-iommu.c: fix variable 'iommu' set but not usedQian Cai1-1/+2
Commit cf04eee8bf0e ("iommu/vt-d: Include ACPI devices in iommu=pt") added for_each_active_iommu() in iommu_prepare_static_identity_mapping() but never used the each element, i.e, "drhd->iommu". drivers/iommu/intel-iommu.c: In function 'iommu_prepare_static_identity_mapping': drivers/iommu/intel-iommu.c:3037:22: warning: variable 'iommu' set but not used [-Wunused-but-set-variable] struct intel_iommu *iommu; Fixed the warning by appending a compiler attribute __maybe_unused for it. Link: http://lkml.kernel.org/r/20190523013314.2732-1-cai@lca.pw Signed-off-by: Qian Cai <cai@lca.pw> Suggested-by: Andrew Morton <akpm@linux-foundation.org> Cc: Joerg Roedel <jroedel@suse.de> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01spdxcheck.py: fix directory structuresVincenzo Frascino1-3/+4
The LICENSE directory has recently changed structure and this makes spdxcheck fails as per below: FAIL: "Blob or Tree named 'other' not found" Traceback (most recent call last): File "scripts/spdxcheck.py", line 240, in <module> spdx = read_spdxdata(repo) File "scripts/spdxcheck.py", line 41, in read_spdxdata for el in lictree[d].traverse(): [...] KeyError: "Blob or Tree named 'other' not found" Fix the script to restore the correctness on checkpatch License checking. References: 62be257e986d ("LICENSES: Rename other to deprecated") References: 8ea8814fcdcb ("LICENSES: Clearly mark dual license only licenses") Link: http://lkml.kernel.org/r/20190523084755.56739-1-vincenzo.frascino@arm.com Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Joe Perches <joe@perches.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jeremy Cline <jcline@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01kasan: initialize tag to 0xff in __kasan_kmallocNathan Chancellor1-1/+1
When building with -Wuninitialized and CONFIG_KASAN_SW_TAGS unset, Clang warns: mm/kasan/common.c:484:40: warning: variable 'tag' is uninitialized when used here [-Wuninitialized] kasan_unpoison_shadow(set_tag(object, tag), size); ^~~ set_tag ignores tag in this configuration but clang doesn't realize it at this point in its pipeline, as it points to arch_kasan_set_tag as being the point where it is used, which will later be expanded to (void *)(object) without a use of tag. Initialize tag to 0xff, as it removes this warning and doesn't change the meaning of the code. Link: https://github.com/ClangBuiltLinux/linux/issues/465 Link: http://lkml.kernel.org/r/20190502163057.6603-1-natechancellor@gmail.com Fixes: 7f94ffbc4c6a ("kasan: add hooks implementation for tag-based mode") Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01z3fold: fix sheduling while atomicVitaly Wool1-5/+6
kmem_cache_alloc() may be called from z3fold_alloc() in atomic context, so we need to pass correct gfp flags to avoid "scheduling while atomic" bug. Link: http://lkml.kernel.org/r/20190523153245.119dfeed55927e8755250ddd@gmail.com Fixes: 7c2b8baa61fe5 ("mm/z3fold.c: add structure for buddy handles") Signed-off-by: Vitaly Wool <vitaly.vul@sony.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01scripts/gdb: fix invocation when CONFIG_COMMON_CLK is not setFabiano Rosas1-1/+2
CLK_GET_RATE_NOCACHE depends on CONFIG_COMMON_CLK. Importing constants.py when CONFIG_COMMON_CLK is not defined causes: (gdb) lx-symbols (...) File "scripts/gdb/linux/proc.py", line 15, in <module> from linux import constants File "scripts/gdb/linux/constants.py", line 2, in <module> LX_CLK_GET_RATE_NOCACHE = gdb.parse_and_eval("CLK_GET_RATE_NOCACHE") gdb.error: No symbol "CLK_GET_RATE_NOCACHE" in current context. Link: http://lkml.kernel.org/r/20190523195313.24701-1-farosas@linux.ibm.com Fixes: e7e6f462c1be ("scripts/gdb: print cached rate in lx-clk-summary") Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: Jackie Liu <liuyun01@kylinos.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-06-01mm/gup: continue VM_FAULT_RETRY processing even for pre-faultsMike Rapoport1-7/+8
When get_user_pages*() is called with pages = NULL, the processing of VM_FAULT_RETRY terminates early without actually retrying to fault-in all the pages. If the pages in the requested range belong to a VMA that has userfaultfd registered, handle_userfault() returns VM_FAULT_RETRY *after* user space has populated the page, but for the gup pre-fault case there's no actual retry and the caller will get no pages although they are present. This issue was uncovered when running post-copy memory restore in CRIU after d9c9ce34ed5c ("x86/fpu: Fault-in user stack if copy_fpstate_to_sigframe() fails"). After this change, the copying of FPU state to the sigframe switched from copy_to_user() variants which caused a real page fault to get_user_pages() with pages parameter set to NULL. In post-copy mode of CRIU, the destination memory is managed with userfaultfd and lack of the retry for pre-fault case in get_user_pages() causes a crash of the restored process. Making the pre-fault behavior of get_user_pages() the same as the "normal" one fixes the issue. Link: http://lkml.kernel.org/r/1557844195-18882-1-git-send-email-rppt@linux.ibm.com Fixes: d9c9ce34ed5c ("x86/fpu: Fault-in user stack if copy_fpstate_to_sigframe() fails") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Tested-by: Andrei Vagin <avagin@gmail.com> [https://travis-ci.org/avagin/linux/builds/533184940] Tested-by: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Borislav Petkov <bp@suse.de> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>