| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The routines in scsi_pm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by checking q->dev in block layer before
handle runtime PM. Since ses doesn't define any PM callbacks and call
blk_pm_runtime_init(), the crash won't occur.
This fixes Bugzilla #101371.
https://bugzilla.kernel.org/show_bug.cgi?id=101371
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Xiangliang Yu <Xiangliang.Yu@amd.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Terry <Michael.terry@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
lpc-eth 31060000.ethernet: error getting resources.
lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qdisc_tree_decrease_qlen() suffers from two problems on multiqueue
devices.
One problem is that it updates sch->q.qlen and sch->qstats.drops
on the mq/mqprio root qdisc, while it should not : Daniele
reported underflows errors :
[ 681.774821] PAX: sch->q.qlen: 0 n: 1
[ 681.774825] PAX: size overflow detected in function qdisc_tree_decrease_qlen net/sched/sch_api.c:769 cicus.693_49 min, count: 72, decl: qlen; num: 0; context: sk_buff_head;
[ 681.774954] CPU: 2 PID: 19 Comm: ksoftirqd/2 Tainted: G O 4.2.6.201511282239-1-grsec #1
[ 681.774955] Hardware name: ASUSTeK COMPUTER INC. X302LJ/X302LJ, BIOS X302LJ.202 03/05/2015
[ 681.774956] ffffffffa9a04863 0000000000000000 0000000000000000 ffffffffa990ff7c
[ 681.774959] ffffc90000d3bc38 ffffffffa95d2810 0000000000000007 ffffffffa991002b
[ 681.774960] ffffc90000d3bc68 ffffffffa91a44f4 0000000000000001 0000000000000001
[ 681.774962] Call Trace:
[ 681.774967] [<ffffffffa95d2810>] dump_stack+0x4c/0x7f
[ 681.774970] [<ffffffffa91a44f4>] report_size_overflow+0x34/0x50
[ 681.774972] [<ffffffffa94d17e2>] qdisc_tree_decrease_qlen+0x152/0x160
[ 681.774976] [<ffffffffc02694b1>] fq_codel_dequeue+0x7b1/0x820 [sch_fq_codel]
[ 681.774978] [<ffffffffc02680a0>] ? qdisc_peek_dequeued+0xa0/0xa0 [sch_fq_codel]
[ 681.774980] [<ffffffffa94cd92d>] __qdisc_run+0x4d/0x1d0
[ 681.774983] [<ffffffffa949b2b2>] net_tx_action+0xc2/0x160
[ 681.774985] [<ffffffffa90664c1>] __do_softirq+0xf1/0x200
[ 681.774987] [<ffffffffa90665ee>] run_ksoftirqd+0x1e/0x30
[ 681.774989] [<ffffffffa90896b0>] smpboot_thread_fn+0x150/0x260
[ 681.774991] [<ffffffffa9089560>] ? sort_range+0x40/0x40
[ 681.774992] [<ffffffffa9085fe4>] kthread+0xe4/0x100
[ 681.774994] [<ffffffffa9085f00>] ? kthread_worker_fn+0x170/0x170
[ 681.774995] [<ffffffffa95d8d1e>] ret_from_fork+0x3e/0x70
mq/mqprio have their own ways to report qlen/drops by folding stats on
all their queues, with appropriate locking.
A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup()
without proper locking : concurrent qdisc updates could corrupt the list
that qdisc_match_from_root() parses to find a qdisc given its handle.
Fix first problem adding a TCQ_F_NOPARENT qdisc flag that
qdisc_tree_decrease_qlen() can use to abort its tree traversal,
as soon as it meets a mq/mqprio qdisc children.
Second problem can be fixed by RCU protection.
Qdisc are already freed after RCU grace period, so qdisc_list_add() and
qdisc_list_del() simply have to use appropriate rcu list variants.
A future patch will add a per struct netdev_queue list anchor, so that
qdisc_tree_decrease_qlen() can have more efficient lookups.
Reported-by: Daniele Fucini <dfucini@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each openvswitch tunnel vport (vxlan,gre,geneve) holds a reference
to the underlying tunnel device, but never released it when such
device is deleted.
Deleting the underlying device via the ip tool cause the kernel to
hangup in the netdev_wait_allrefs() loop.
This commit ensure that on device unregistration dp_detach_port_notify()
is called for all vports that hold the device reference, properly
releasing it.
Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device")
Fixes: b2acd1dc3949 ("openvswitch: Use regular GRE net_device instead of vport")
Fixes: 6b001e682e90 ("openvswitch: Use Geneve device.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a multicast group is joined on a socket, a struct ip_mc_socklist
is appended to the sockets mc_list containing information about the
joined group.
If the interface is hot unplugged, this entry becomes stale. Prior to
commit 52ad353a5344f ("igmp: fix the problem when mc leave group") it
was possible to remove the stale entry by performing a
IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on
the interface. However, this fix enforces that the interface must
still exist. Thus with time, the number of stale entries grows, until
sysctl_igmp_max_memberships is reached and then it is not possible to
join and more groups.
The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is
performed without specifying the interface, either by ifindex or ip
address. However here we do supply one of these. So loosen the
restriction on device existence to only apply when the interface has
not been specified. This then restores the ability to clean up the
stale entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 52ad353a5344f "(igmp: fix the problem when mc leave group")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry Vyukov reported a memory leak using IPV6 SCTP sockets.
We need to call inet6_destroy_sock() to properly release
inet6 specific fields.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
aarch64 doesn't have native store immediate instruction, such operation
has to be implemented by the below instruction sequence:
Load immediate to register
Store register
Signed-off-by: Yang Shi <yang.shi@linaro.org>
CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.
ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.
__ip6_dst_store() and ip6_dst_store() share same implementation.
sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()
Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.
This is because ip6_dst_store() can be called from process context,
without any lock held.
As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()
Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch completes the work I did in commit 45f6fad84cc3
("ipv6: add complete rcu protection around np->opt"), as I missed
sctp part.
This simply makes sure np->opt is used with proper RCU locking
and accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Proxy entries could have null pointer to net-device.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Fixes: 84920c1420e2 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry Vyukov reported that the user could trigger a kernel warning by
using a large len value for getsockopt SCTP_GET_LOCAL_ADDRS, as that
value directly affects the value used as a kmalloc() parameter.
This patch thus switches the allocation flags from all user-controllable
kmalloc size to GFP_USER to put some more restrictions on it and also
disables the warn, as they are not necessary.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
They don't need to be any bigger than that and with this we start a new
bitfield for tracking association runtime stuff, like zero window
situation.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses multiple problems :
UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.
Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())
This patch adds full RCU protection to np->opt
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For large map->value_size the user space can trigger memory allocation warnings like:
WARNING: CPU: 2 PID: 11122 at mm/page_alloc.c:2989
__alloc_pages_nodemask+0x695/0x14e0()
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff82743b56>] dump_stack+0x68/0x92 lib/dump_stack.c:50
[<ffffffff81244ec9>] warn_slowpath_common+0xd9/0x140 kernel/panic.c:460
[<ffffffff812450f9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:493
[< inline >] __alloc_pages_slowpath mm/page_alloc.c:2989
[<ffffffff81554e95>] __alloc_pages_nodemask+0x695/0x14e0 mm/page_alloc.c:3235
[<ffffffff816188fe>] alloc_pages_current+0xee/0x340 mm/mempolicy.c:2055
[< inline >] alloc_pages include/linux/gfp.h:451
[<ffffffff81550706>] alloc_kmem_pages+0x16/0xf0 mm/page_alloc.c:3414
[<ffffffff815a1c89>] kmalloc_order+0x19/0x60 mm/slab_common.c:1007
[<ffffffff815a1cef>] kmalloc_order_trace+0x1f/0xa0 mm/slab_common.c:1018
[< inline >] kmalloc_large include/linux/slab.h:390
[<ffffffff81627784>] __kmalloc+0x234/0x250 mm/slub.c:3525
[< inline >] kmalloc include/linux/slab.h:463
[< inline >] map_update_elem kernel/bpf/syscall.c:288
[< inline >] SYSC_bpf kernel/bpf/syscall.c:744
To avoid never succeeding kmalloc with order >= MAX_ORDER check that
elem->value_size and computed elem_size are within limits for both hash and
array type maps.
Also add __GFP_NOWARN to kmalloc(value_size | elem_size) to avoid OOM warnings.
Note kmalloc(key_size) is highly unlikely to trigger OOM, since key_size <= 512,
so keep those kmalloc-s as-is.
Large value_size can cause integer overflows in elem_size and map.pages
formulas, so check for that as well.
Fixes: aaac3ba95e4c ("bpf: charge user for creation of BPF maps and programs")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet controller found in the Armada 38x SoC's family support
TCP/IP checksumming with frame sizes larger than 1600 bytes, however
only on port 0.
This commit enables it by setting 'tx-csum-limit' to 9800B in
'ethernet@70000' node.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e32894191 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.
Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.
Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.
Fixes: 3b79af973cf4 ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.
If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Interfaces are being initialized (setup) on addition,
and torn down on removal.
However, p2p device is being torn down when stopped,
resulting in the next p2p start operation being done
on uninitialized interface.
Solve it by calling ieee80211_teardown_sdata() only
on interface removal (for the non-netdev case).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[squashed in fix to call teardown after unregister]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.
This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Properly set CQ timer threshold and also set it to 2us.
With previous incorrect settings it was set to 0.5us which is too less.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After 614732eaa12d, no refcount is maintained for the vport-vxlan module.
This allows the userspace to remove such module while vport-vxlan
devices still exist, which leads to later oops.
v1 -> v2:
- move vport 'owner' initialization in ovs_vport_ops_register()
and make such function a macro
Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like 29fae1c85 ("HID: logitech: Add support for G29") was a little
bit aggressive and broke other devices.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=108121
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
During own review but also reported by Dmitry's syzkaller [1] it has been
noticed that we trigger a heap out-of-bounds access on eBPF array maps
when updating elements. This happens with each map whose map->value_size
(specified during map creation time) is not multiple of 8 bytes.
In array_map_alloc(), elem_size is round_up(attr->value_size, 8) and
used to align array map slots for faster access. However, in function
array_map_update_elem(), we update the element as ...
memcpy(array->value + array->elem_size * index, value, array->elem_size);
... where we access 'value' out-of-bounds, since it was allocated from
map_update_elem() from syscall side as kmalloc(map->value_size, GFP_USER)
and later on copied through copy_from_user(value, uvalue, map->value_size).
Thus, up to 7 bytes, we can access out-of-bounds.
Same could happen from within an eBPF program, where in worst case we
access beyond an eBPF program's designated stack.
Since 1be7f75d1668 ("bpf: enable non-root eBPF programs") didn't hit an
official release yet, it only affects priviledged users.
In case of array_map_lookup_elem(), the verifier prevents eBPF programs
from accessing beyond map->value_size through check_map_access(). Also
from syscall side map_lookup_elem() only copies map->value_size back to
user, so nothing could leak.
[1] http://github.com/google/syzkaller
Fixes: 28fbcfa08d8e ("bpf: add array type of eBPF maps")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The set_event_pid filter relies on attaching to the sched_switch and
sched_wakeup tracepoints to see if it should filter the tracing on schedule
tracepoints. By adding the callbacks to sched_wakeup, pids in the
set_event_pid file will trace the wakeups of those tasks with those pids.
But sched_wakeup_new and sched_waking were missed. These two should also be
traced. Luckily, these tracepoints share the same class as sched_wakeup
which means they can use the same pre and post callbacks as sched_wakeup
does.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Dmitry provided a syzkaller (http://github.com/google/syzkaller)
triggering a fault in sock_wake_async() when async IO is requested.
Said program stressed af_unix sockets, but the issue is generic
and should be addressed in core networking stack.
The problem is that by the time sock_wake_async() is called,
we should not access the @flags field of 'struct socket',
as the inode containing this socket might be freed without
further notice, and without RCU grace period.
We already maintain an RCU protected structure, "struct socket_wq"
so moving SOCKWQ_ASYNC_NOSPACE & SOCKWQ_ASYNC_WAITDATA into it
is the safe route.
It also reduces number of cache lines needing dirtying, so might
provide a performance improvement anyway.
In followup patches, we might move remaining flags (SOCK_NOSPACE,
SOCK_PASSCRED, SOCK_PASSSEC) to save 8 bytes and let 'struct socket'
being mostly read and let it being shared between cpus.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is a cleanup to make following patch easier to
review.
Goal is to move SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
from (struct socket)->flags to a (struct socket_wq)->flags
to benefit from RCU protection in sock_wake_async()
To ease backports, we rename both constants.
Two new helpers, sk_set_bit(int nr, struct sock *sk)
and sk_clear_bit(int net, struct sock *sk) are added so that
following patch can change their implementation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent patches added basic support for the Apple NVMe controller but
still cause resets and data corruption on that particular controller
when a specific pattern of read/flush commands occurs. Limiting the
queue depth to 2 works around that issue.
This patch enforces that limit only for the Apple controller and is
considered a temporary fix until we find the root source of that
problem.
Signed-off-by: Stephan Günther <guenther@tum.de>
Signed-off-by: Maurice Leclaire <leclaire@in.tum.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
vmxnet3_drv does not check dma_addr with dma_mapping_error()
after mapping dma memory. The patch adds the checks and
tries to handle failures.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The N_X25 line discipline may access the previous line discipline's closed
and already-freed private data on open [1].
The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).
[1]
[ 634.336761] ==================================================================
[ 634.338226] BUG: KASAN: use-after-free in x25_asy_open_tty+0x13d/0x490 at addr ffff8800a743efd0
[ 634.339558] Read of size 4 by task syzkaller_execu/8981
[ 634.340359] =============================================================================
[ 634.341598] BUG kmalloc-512 (Not tainted): kasan: bad access detected
...
[ 634.405018] Call Trace:
[ 634.405277] dump_stack (lib/dump_stack.c:52)
[ 634.405775] print_trailer (mm/slub.c:655)
[ 634.406361] object_err (mm/slub.c:662)
[ 634.406824] kasan_report_error (mm/kasan/report.c:138 mm/kasan/report.c:236)
[ 634.409581] __asan_report_load4_noabort (mm/kasan/report.c:279)
[ 634.411355] x25_asy_open_tty (drivers/net/wan/x25_asy.c:559 (discriminator 1))
[ 634.413997] tty_ldisc_open.isra.2 (drivers/tty/tty_ldisc.c:447)
[ 634.414549] tty_set_ldisc (drivers/tty/tty_ldisc.c:567)
[ 634.415057] tty_ioctl (drivers/tty/tty_io.c:2646 drivers/tty/tty_io.c:2879)
[ 634.423524] do_vfs_ioctl (fs/ioctl.c:43 fs/ioctl.c:607)
[ 634.427491] SyS_ioctl (fs/ioctl.c:622 fs/ioctl.c:613)
[ 634.427945] entry_SYSCALL_64_fastpath (arch/x86/entry/entry_64.S:188)
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit ab450605b35caa768ca33e86db9403229bf42be4.
In IPv6, we cannot inherit the dst of the original dst. ndisc packets
are IPv6 packets and may take another route than the original packet.
This patch breaks the following scenario: a packet comes from eth0 and
is forwarded through vxlan1. The encapsulated packet triggers an NS
which cannot be sent because of the wrong route.
CC: Jiri Benc <jbenc@redhat.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit at least doubles the maximum value for
completion_nsec. This helps in special cases where one wants/needs to
emulate an extremely slow I/O (for example to spot bugs).
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Arianna Avanzini <avanzini@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In single-queue (block layer) mode,the function null_rq_prep_fn stops
the device if alloc_cmd fails. Then, once stopped, the device must be
restarted on the next command completion, so that the request(s) for
which alloc_cmd failed can be requeued. Otherwise the device hangs.
Unfortunately, device restart is currently performed only for delayed
completions, i.e., in irqmode==2. This fact causes hangs, for the
above reasons, with the other irqmodes in combination with single-queue
block layer.
This commits addresses this issue by making sure that, if stopped, the
device is properly restarted for all irqmodes on completions.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Arianna AVanzini <avanzini@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
For the Timer IRQ mode (i.e., when command completions are delayed),
there is one timer for each CPU. Each of these timers
. has a completion queue associated with it, containing all the
command completions to be executed when the timer fires;
. is set, and a new completion-to-execute is inserted into its
completion queue, every time the dispatch code for a new command
happens to be executed on the CPU related to the timer.
This implies that, if the dispatch of a new command happens to be
executed on a CPU whose timer has already been set, but has not yet
fired, then the timer is set again, to the completion time of the
newly arrived command. When the timer eventually fires, all its queued
completions are executed.
This way of handling delayed command completions entails the following
problem: if more than one command completion is inserted into the
queue of a timer before the timer fires, then the expiration time for
the timer is moved forward every time each of these completions is
enqueued. As a consequence, only the last completion enqueued enjoys a
correct execution time, while all previous completions are unjustly
delayed until the last completion is executed (and at that time they
are executed all together).
Specifically, if all the above completions are enqueued almost at the
same time, then the problem is negligible. On the opposite end, if
every completion is enqueued a while after the previous completion was
enqueued (in the extreme case, it is enqueued only right before the
timer would have expired), then every enqueued completion, except for
the last one, experiences an inflated delay, proportional to the number
of completions enqueued after it. In the end, commands, and thus I/O
requests, may be completed at an arbitrarily lower rate than the
desired one.
This commit addresses this issue by replacing per-CPU timers with
per-command timers, i.e., by associating an individual timer with each
command.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Arianna Avanzini <avanzini@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
When building for SH7734:
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:2: error: '_GP_DATA' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:1: error: macro "_GP_INOUTSEL" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:53: error: '_GP_INOUTSEL' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:1: error: macro "_GP_INDT" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:47: error: '_GP_INDT' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
Add the missing "cfg" macro parameters to the sh7734-specific
_GP_DATA(), _GP_INOUTSEL(), and _GP_INDT() macros to fix this.
Fixes: 22768fc60abbf58b ("pinctrl: sh-pfc: Add macros defining GP ports with config flags")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Dmitry provided a syzkaller (http://github.com/google/syzkaller)
generated program that triggers the WARNING at
net/ipv4/tcp.c:1729 in tcp_recvmsg() :
WARN_ON(tp->copied_seq != tp->rcv_nxt &&
!(flags & (MSG_PEEK | MSG_TRUNC)));
His program is specifically attempting a Cross SYN TCP exchange,
that we support (for the pleasure of hackers ?), but it looks we
lack proper tcp->copied_seq initialization.
Thanks again Dmitry for your report and testings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The gianfar driver has recently been enabled on arm64 but fails to build
since it check the return value of platform_get_irq() against NO_IRQ. Fix
this by instead checking for a negative error code.
Even on ARM where this code was previously being built this check was
incorrect since platform_get_irq() returns a negative error code which
may not be exactly the (unsigned int)(-1) that NO_IRQ is defined to be.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver can be built on arm64 but relies on NO_IRQ to check the return
value of irq_of_parse_and_map() which fails to build on arm64 because the
architecture does not provide a NO_IRQ. Fix this to correctly check the
return value of irq_of_parse_and_map().
Even on ARM systems where the driver was previously used the check was
broken since on ARM NO_IRQ is -1 but irq_of_parse_and_map() returns 0 on
error.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sendpage did not care about credentials at all. This could lead to
situations in which because of fd passing between processes we could
append data to skbs with different scm data. It is illegal to splice those
skbs together. Instead we have to allocate a new skb and if requested
fill out the scm details.
Fixes: 869e7c62486ec ("net: af_unix: implement stream sendpage support")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Ken Xue
Jérôme Pouiller
Michael Chan
Jeffrey Huang
Vladimir Zapolskiy
Eric Dumazet
Paolo Abeni
Andrew Lunn
Yang Shi
Konstantin Khlebnikov
Marcelo Ricardo Leitner
Alexei Starovoitov
Marcin Wojtas
Johannes Berg
Antonio Quartulli
Eliad Peller
Sunil Goutham
Thanneeru Srinivasulu
Benjamin Tissoires
Daniel Borkmann
Steven Rostedt (Red Hat)
Stephan Günther
Alexey Khoroshilov
Peter Hurley
Nicolas Dichtel
Arianna Avanzini
Paolo Valente
Geert Uytterhoeven
Mark Brown
Hannes Frederic Sowa