| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the datasheet the typical value for VDD_SNVS should be
800 mV, so let's make sure that this is within the range of the
regulator.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It looks like the voltages for the SOC and DRAM supply weren't properly
validated before. The datasheet and uboot-imx code tells us that VDD_SOC
should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM should be
950 mV for DDR clock frequencies of up to 1.5 GHz.
Let's fix these values to make sure the voltages are within the required
range.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Starting with commit 6b2117ad65f1 ("of: property: fw_devlink: Add
support for "resets" and "pwms""), the imx-drm driver fails to load
due to forever dormant devlinks to the reset-controller node. This
node was never associated with a struct device.
Add a platform device to allow fw_devnode to activate the devlinks.
Fixes: 6b2117ad65f1 ("of: property: fw_devlink: Add support for "resets" and "pwms"")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix invalid M2_RST# gpio pinmux.
Fixes: ef484dfcf6f7 ("arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Any pending interrupt can prevent entering standby based power off state.
To avoid it, disable the GIC CPU interface.
Fixes: 8148d2136002 ("ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On the LS1028A this instance of the eSDHC controller is intended for
either an eMMC or eSDIO card. It doesn't provide a card detect pin and
its IO voltage is fixed at 1.8V.
Remove the bogus broken-cd property, instead add the non-removable
property. Fix the voltage-ranges property and set it to 1.8V only.
Fixes: 491d3a3fc113 ("arm64: dts: ls1028a: Add esdhc node in dts")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The buck2 output of the PMIC is the VDD core voltage of the cpu.
Switching off this will poweroff the CPU. Add the 'regulator-always-on'
property to avoid this.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
qspi and fspi host controller do not support read 1-4-4 mode. so need to
set the tx to 1, let the common code finally select read 1-1-4 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable CONFIG_FB which is nowadays required for CONFIG_DRM_PANEL_LVDS,
CONFIG_DRM_PANEL_SIMPLE, CONFIG_DRM_PANEL_SEIKO_43WVF1G,
CONFIG_FB_MODE_HELPERS, CONFIG_BACKLIGHT_PWM, CONFIG_BACKLIGHT_GPIO,
CONFIG_FRAMEBUFFER_CONSOLE, CONFIG_LOGO, CONFIG_FONTS, CONFIG_FONT_8x8
and CONFIG_FONT_8x16.
Fixes: f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79dfdf ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0ef14bbb3 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a6d3 ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693db6 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This reverts commit cc8870bf4c3ab0af385538460500a9d342ed945f.
Since commit cc8870bf4c3a ("ARM: imx6q: drop of_platform_default_populate()
from init_machine") the following errors are seen on boot:
[ 0.123372] imx6q_suspend_init: failed to find ocram device!
[ 0.123537] imx6_pm_common_init: No DDR LPM support with suspend -19!
, which break suspend/resume on imx6q/dl.
Revert the offeding commit to avoid the regression.
Thanks to Tim Harvey for bisecting this problem.
Cc: stable@vger.kernel.org
Fixes: cc8870bf4c3a ("ARM: imx6q: drop of_platform_default_populate() from init_machine")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since the LED multicolor framework support was added in commit
92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd4c ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
Picking the changes from:
17ce9c61c71cbc0d ("drm: document DRM_IOCTL_MODE_RMFB")
Doesn't result in any tooling changes:
$ tools/perf/trace/beauty/drm_ioctl.sh > before
$ cp include/uapi/drm/drm.h tools/include/uapi/drm/drm.h
$ tools/perf/trace/beauty/drm_ioctl.sh > after
$ diff -u before after
Silencing these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/drm/drm.h' differs from latest version at 'include/uapi/drm/drm.h'
diff -u tools/include/uapi/drm/drm.h include/uapi/drm/drm.h
Cc: Simon Ser <contact@emersion.fr>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the changes in:
b65a9489730a2494 ("drm/i915/userptr: Probe existence of backing struct pages upon creation")
ee242ca704d38699 ("drm/i915/guc: Implement GuC priority management")
81340cf3bddded4f ("drm/i915/uapi: reject set_domain for discrete")
7961c5b60f23dff5 ("drm/i915: Add TTM offset argument to mmap.")
aef7b67a79564f6c ("drm/i915/uapi: convert drm_i915_gem_userptr to kernel doc")
e7737b67ab46ee0e ("drm/i915/uapi: reject caching ioctls for discrete")
3aa8c57fe25a9247 ("drm/i915/uapi: convert drm_i915_gem_set_domain to kernel doc")
289f5a72009b8f67 ("drm/i915/uapi: convert drm_i915_gem_caching to kernel doc")
4a766ae40ec83301 ("drm/i915: Drop the CONTEXT_CLONE API (v2)")
6ff6d61dd2a943bd ("drm/i915: Drop I915_CONTEXT_PARAM_NO_ZEROMAP")
fe4751c3d513ff4f ("drm/i915: Drop I915_CONTEXT_PARAM_RINGSIZE")
577729533cdc4e37 ("drm/i915: Document the Virtual Engine uAPI")
c649432e86ca677d ("drm/i915: Fix busy ioctl commentary")
That doesn't result in any changes to tooling as no new ioctl were
added (at least not perceived by tools/perf/trace/beauty/drm_ioctl.sh).
Addressing this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
diff -u tools/include/uapi/drm/i915_drm.h include/uapi/drm/i915_drm.h
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the change in:
7957d93bf32bc211 ("block: add ioctl to read the disk sequence number")
It adds a new ioctl, but we are still not using that to generate tables
for 'perf trace', so no changes in tooling.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/fs.h' differs from latest version at 'include/uapi/linux/fs.h'
diff -u tools/include/uapi/linux/fs.h include/uapi/linux/fs.h
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the changes in:
db243b796439c0ca ("net/ipv4/ipv6: Replace one-element arraya with flexible-array members")
2d3e5caf96b9449a ("net/ipv4: Replace one-element array with flexible-array member")
That don't result in any change in tooling, the structs changed remains
with the same layout.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Some distributions, like debian, don't link perf with libbfd. Add a
build flag to make this configuration buildable and testable.
This was inspired by:
https://lore.kernel.org/linux-perf-users/20210910102307.2055484-1-tonyg@leastfixedpoint.com/T/#u
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: tony garnock-jones <tonyg@leastfixedpoint.com>
Link: http://lore.kernel.org/lkml/20210910225756.729087-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
$ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115b321ed ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
A config terms list was spliced twice, resulting in a never-ending loop
when the list was traversed. Fix by using list_splice_init() and copying
and freeing the lists as necessary.
This patch also depends on patch "perf tools: Factor out
copy_config_terms() and free_config_terms()"
Example on ADL:
Before:
# perf record -e '{intel_pt//,cycles/aux-sample-size=4096/pp}' uname &
# jobs
[1]+ Running perf record -e "{intel_pt//,cycles/aux-sample-size=4096/pp}" uname
# perf top -E 10
PerfTop: 4071 irqs/sec kernel: 6.9% exact: 100.0% lost: 0/0 drop: 0/0 [4000Hz cycles], (all, 24 CPUs)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
97.60% perf [.] __evsel__get_config_term
0.25% [kernel] [k] kallsyms_expand_symbol.constprop.13
0.24% perf [.] kallsyms__parse
0.15% [kernel] [k] _raw_spin_lock
0.14% [kernel] [k] number
0.13% [kernel] [k] advance_transaction
0.08% [kernel] [k] format_decode
0.08% perf [.] map__process_kallsym_symbol
0.08% perf [.] rb_insert_color
0.08% [kernel] [k] vsnprintf
exiting.
# kill %1
After:
# perf record -e '{intel_pt//,cycles/aux-sample-size=4096/pp}' uname &
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.060 MB perf.data ]
# perf script | head
perf-exec 604 [001] 1827.312293: psb: psb offs: 0 ffffffffb8415e87 pt_config_start+0x37 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb856a3bd event_sched_in.isra.133+0xfd ([kernel.kallsyms]) => ffffffffb856a9a0 perf_pmu_nop_void+0x0 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb856b10e merge_sched_in+0x26e ([kernel.kallsyms]) => ffffffffb856a2c0 event_sched_in.isra.133+0x0 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb856a45d event_sched_in.isra.133+0x19d ([kernel.kallsyms]) => ffffffffb8568b80 perf_event_set_state.part.61+0x0 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb8568b86 perf_event_set_state.part.61+0x6 ([kernel.kallsyms]) => ffffffffb85662a0 perf_event_update_time+0x0 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb856a35c event_sched_in.isra.133+0x9c ([kernel.kallsyms]) => ffffffffb8567610 perf_log_itrace_start+0x0 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb856a377 event_sched_in.isra.133+0xb7 ([kernel.kallsyms]) => ffffffffb8403b40 x86_pmu_add+0x0 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb8403b86 x86_pmu_add+0x46 ([kernel.kallsyms]) => ffffffffb8403940 collect_events+0x0 ([kernel.kallsyms])
perf-exec 604 1827.312293: 1 branches: ffffffffb8403a7b collect_events+0x13b ([kernel.kallsyms]) => ffffffffb8402cd0 collect_event+0x0 ([kernel.kallsyms])
Fixes: 30def61f64bac5 ("perf parse-events Create two hybrid cache events")
Fixes: 94da591b1c7913 ("perf parse-events Create two hybrid raw events")
Fixes: 9cbfa2f64c04d9 ("perf parse-events Create two hybrid hardware events")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Link: https //lore.kernel.org/r/20210909125508.28693-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Factor out copy_config_terms() and free_config_terms() so that they can
be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Link: https //lore.kernel.org/r/20210909125508.28693-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Some fields are missing and text_poke is duplicated. Fix that up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20210911120550.12203-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When building directly on the checked out repository the build process
produces a file that should be ignored, so add it to .gitignore.
Fixes: a81df63a5df3e195 ("perf doc: Fix doc.dep")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910232249.739661-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
_ex_table section is read-only, so move it to RO_DATA.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Enable BUILDTIME_TABLE_SORT to sort the exception table at build time
rather than during boot.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Currently, nothing is output on the serial console, unless
"console=ttyS0,115200n8" or "earlycon" are appended to the kernel
command line. Enable automatic console selection using
chosen/stdout-path by adding a proper alias, and configure the expected
serial rate.
While at it, add aliases for the other three serial ports, which are
provided on the same micro-USB connector as the first one.
Fixes: 0fa6107eca4186ad ("RISC-V: Initial DTS for Microchip ICICLE board")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Currently, the (z)install targets in arch/riscv/Makefile descend into
arch/riscv/boot/Makefile to invoke the shell script, but there is no
good reason to do so.
arch/riscv/Makefile can run the shell script directly.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
This enlarges the bits availiable for stack randomisation on RV64 from
the default of 8MiB to 1GiB, to match arm64 and x86.
Also, update the documentation to reflect our support for stack
randomisation.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[Palmer: commit text]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
The EFI system partition uses the FAT file system. Many distributions add
an entry in /etc/fstab for the ESP. We must ensure that mounting does not
fail.
The default code page for FAT is 437 (cf. CONFIG_FAT_DEFAULT_CODEPAGE).
The default IO character set is "iso8859-1" (cf. CONFIG_NLS_ISO8859_1).
So let's enable NLS_CODEPAGE_437 and NLS_ISO8859_1 in defconfig.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
NVMe is a non-volatile storage media attached via PCIe.
As NVMe has much higher throughput than other block devices like
SATA it is a must have for RISC-V. Enable CONFIG_BLK_DEV_NVME.
The HiFive Unmatched is a board providing M.2 slots for NVMe drives.
Enable CONFIG_PCIE_FU740.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Dave stumbled over the incomplete and confusing documentation of the CPU
hotplug API.
Rewrite it, add the missing function documentations and correct the
existing ones.
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210909123212.489059409@linutronix.de
|
|
No users in tree use the deprecated CPU-hotplug functions anymore.
Remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-39-bigeasy@linutronix.de
|
|
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-20-bigeasy@linutronix.de
|
|
The btf__get_from_id() function was deprecated in favour of
btf__load_from_kernel_by_id(), but it is still avaiable, so use it to
provide a weak function btf__load_from_kernel_by_id() for older libbpf
when building perf with LIBBPF_DYNAMIC=1, i.e. using the system's libbpf
package.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the changes from:
9ffb14ef61bab83f ("move_mount: allow to add a mount into an existing group")
That ends up adding support for the new MOVE_MOUNT_SET_GROUP move_mount
flag.
$ tools/perf/trace/beauty/move_mount_flags.sh > before
$ cp include/uapi/linux/mount.h tools/include/uapi/linux/mount.h
$ tools/perf/trace/beauty/move_mount_flags.sh > after
$ diff -u before after
--- before 2021-09-10 12:28:43.865279808 -0300
+++ after 2021-09-10 12:28:50.183429184 -0300
@@ -5,4 +5,5 @@
[ilog2(0x00000010) + 1] = "T_SYMLINKS",
[ilog2(0x00000020) + 1] = "T_AUTOMOUNTS",
[ilog2(0x00000040) + 1] = "T_EMPTY_PATH",
+ [ilog2(0x00000100) + 1] = "SET_GROUP",
};
$
So now one can use it in --filter expressions for tracepoints.
This silences this perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/linux/mount.h' differs from latest version at 'include/uapi/linux/mount.h'
diff -u tools/include/uapi/linux/mount.h include/uapi/linux/mount.h
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Previously the regext expected MOVE_MOUNT_[FT]_*, but in the next patch
a flag that doesn't match that expression will be added, MOVE_MOUNT_SET_GROUP
To make this more future proof, take advantage of the fact that the only
one we don't need to cover is MOVE_MOUNT__MASK and use MOVE_MOUNT_[^_]+_*_.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the changes in:
433c38f40f6a81cf ("arm64: mte: change ASYNC and SYNC TCF settings into bitfields")
e893bb1bb4d2eb63 ("x86, prctl: Hook L1D flushing in via prctl")
That don't result in any changes in tooling:
$ tools/perf/trace/beauty/prctl_option.sh > before
$ cp include/uapi/linux/prctl.h tools/include/uapi/linux/prctl.h
$ tools/perf/trace/beauty/prctl_option.sh > after
$ diff -u before after
$
Just silences this perf tools build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/prctl.h' differs from latest version at 'include/uapi/linux/prctl.h'
diff -u tools/include/uapi/linux/prctl.h include/uapi/linux/prctl.h
Cc: Balbir Singh <sblbir@amazon.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Picking the changes from:
81be10934949da8b ("ALSA: pcm: Add SNDRV_PCM_INFO_EXPLICIT_SYNC flag")
Which entails no changes in the tooling side as it doesn't introduce new
ioctls.
To silence this perf tools build warning:
Warning: Kernel ABI header at 'tools/include/uapi/sound/asound.h' differs from latest version at 'include/uapi/sound/asound.h'
diff -u tools/include/uapi/sound/asound.h include/uapi/sound/asound.h
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the changes in:
f95937ccf5bd5e0a ("KVM: stats: Support linear and logarithmic histogram statistics")
f0376edb1ddcab19 ("KVM: arm64: Add ioctl to fetch/store tags in a guest")
ea7fc1bb1cd1b92b ("KVM: arm64: Introduce MTE VM feature")
That just rebuilds perf, as these patches don't add any new KVM ioctl to
be harvested for the the 'perf trace' ioctl syscall argument
beautifiers.
This is also by now used by tools/testing/selftests/kvm/, so that will
pick the new KVM_STATS_TYPE_LINEAR_HIST and KVM_STATS_TYPE_LOG_HIST
defines.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/kvm.h' differs from latest version at 'include/uapi/linux/kvm.h'
diff -u tools/include/uapi/linux/kvm.h include/uapi/linux/kvm.h
Cc: Jing Zhang <jingzhangos@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Steven Price <steven.price@arm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick the changes in:
61e5f69ef08379cd ("KVM: x86: implement KVM_GUESTDBG_BLOCKIRQ")
That just rebuilds kvm-stat.c on x86, no change in functionality.
This silences these perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/uapi/asm/kvm.h' differs from latest version at 'arch/x86/include/uapi/asm/kvm.h'
diff -u tools/arch/x86/include/uapi/asm/kvm.h arch/x86/include/uapi/asm/kvm.h
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Perf records IBS (Instruction Based Sampling) extra sample data when
'perf record --raw-samples' is used with an IBS-compatible event, on a
machine that supports IBS. IBS support is indicated in
CPUID_Fn80000001_ECX bit #10.
Up until now, users have been able to see the extra sample data solely
in raw hex format using 'perf report --dump-raw-trace'. From there,
users could decode the data either manually, or by using an external
script.
Enable the built-in 'perf report --dump-raw-trace' to do the decoding of
the extra sample data bits, so manual or external script decoding isn't
necessary.
Example usage:
$ sudo perf record -c 10000001 -a --raw-samples -e ibs_fetch/rand_en=1/,ibs_op/cnt_ctl=1/ -C 0,1 taskset -c 0,1 7za b -mmt2 | perf report --dump-raw-trace
Stdout contains IBS Fetch samples, e.g.:
ibs_fetch_ctl: 02170007ffffffff MaxCnt 1048560 Cnt 1048560 Lat 7 En 1 Val 1 Comp 1 IcMiss 0 PhyAddrValid 1 L1TlbPgSz 4KB L1TlbMiss 0 L2TlbMiss 0 RandEn 1 L2Miss 0
IbsFetchLinAd: 000056016b2ead40
IbsFetchPhysAd: 000000115cedfd40
c_ibs_ext_ctl: 0000000000000000 IbsItlbRefillLat 0
..and IBS Op samples, e.g.:
ibs_op_ctl: 0000009e009e8968 MaxCnt 10000000 En 1 Val 1 CntCtl 1=uOps CurCnt 158
IbsOpRip: 000056016b2ea73d
ibs_op_data: 00000000000b0002 CompToRetCtr 2 TagToRetCtr 11 BrnRet 0 RipInvalid 0 BrnFuse 0 Microcode 0
ibs_op_data2: 0000000000000002 CacheHitSt 0=M-state RmtNode 0 DataSrc 2=Local node cache
ibs_op_data3: 0000000000c60002 LdOp 0 StOp 1 DcL1TlbMiss 0 DcL2TlbMiss 0 DcL1TlbHit2M 0 DcL1TlbHit1G 0 DcL2TlbHit2M 0 DcMiss 0 DcMisAcc 0 DcWcMemAcc 0 DcUcMemAcc 0 DcLockedOp 0 DcMissNoMabAlloc 0 DcLinAddrValid 1 DcPhyAddrValid 1 DcL2TlbHit1G 0 L2Miss 0 SwPf 0 OpMemWidth 4 bytes OpDcMissOpenMemReqs 0 DcMissLat 0 TlbRefillLat 0
IbsDCLinAd: 00007f133c319ce0
IbsDCPhysAd: 0000000270485ce0
Committer notes:
Fixed up this:
util/amd-sample-raw.c: In function ‘evlist__amd_sample_raw’:
util/amd-sample-raw.c:125:42: error: ‘ bytes’ directive output may be truncated writing 6 bytes into a region of size between 4 and 7 [-Werror=format-truncation=]
125 | " OpMemWidth %2d bytes", 1 << (reg.op_mem_width - 1));
| ^~~~~~
In file included from /usr/include/stdio.h:866,
from util/amd-sample-raw.c:7:
/usr/include/bits/stdio2.h:71:10: note: ‘__builtin___snprintf_chk’ output between 21 and 24 bytes into a destination of size 21
71 | return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
72 | __glibc_objsize (__s), __fmt,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
73 | __va_arg_pack ());
| ~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
As that %2d won't limit the number of chars to 2, just state that 2 is
the minimal width:
$ cat printf.c
#include <stdio.h>
#include <stdlib.h>
int main(int argc, char *argv[])
{
char bf[64];
int len = snprintf(bf, sizeof(bf), "%2d", atoi(argv[1]));
printf("strlen(%s): %u\n", bf, len);
return 0;
}
$ ./printf 1
strlen( 1): 2
$ ./printf 12
strlen(12): 2
$ ./printf 123
strlen(123): 3
$ ./printf 1234
strlen(1234): 4
$ ./printf 12345
strlen(12345): 5
$ ./printf 123456
strlen(123456): 6
$
And since we probably don't want that output to be truncated, just
assume the worst case, as the compiler did, and add a few more chars to
that buffer.
Also use sizeof(var) instead of sizeof(dup-of-wanted-format-string) to
avoid bugs when changing one but not the other.
I also had to change this:
-#include <asm/amd-ibs.h>
+#include "../../arch/x86/include/asm/amd-ibs.h"
To make it build on other architectures, just like intel-pt does.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Joao Martins <joao.m.martins@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https //lore.kernel.org/r/20210817221509.88391-4-kim.phillips@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This is a tools/-side patch for the patch that adds the original copy
of the IBS header file, in arch/x86/include/asm/.
We also add an entry to check-headers.sh, so future changes continue
to be copied.
Committer notes:
Had to add this
-#include <asm/msr-index.h>
+#include "msr-index.h"
And change the check-headers.sh entry to ignore this line when diffing
with the original kernel header.
This is needed so that we can use 'perf report' on a perf.data with IBS
data on a !x86 system, i.e. building on ARM fails without this as there
is no asm/msr-index.h there.
This was done on the next patch in this series and is done for things
like Intel PT and ARM CoreSight.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Joao Martins <joao.m.martins@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https //lore.kernel.org/r/20210817221509.88391-3-kim.phillips@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Properties with standard unit suffixes such as '-bits' don't need a
type.
Cc: Mark Brown <broonie@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210910165945.2852999-1-robh@kernel.org
|
|
'enum' is equivalent to 'oneOf' with a list of 'const' entries, but 'enum'
is more concise and yields better error messages.
Fix a couple more cases which have appeared.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Mark Brown <broonie@kernel.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Aswath Govindraju <a-govindraju@ti.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Cc: linux-spi@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210910165153.2843871-1-robh@kernel.org
|
|
Fix a leak in s_fsnotify_connectors counter in case of a race between
concurrent add of new fsnotify mark to an object.
The task that lost the race fails to drop the counter before freeing
the unused connector.
Following umount() hangs in fsnotify_sb_delete()/wait_var_event(),
because s_fsnotify_connectors never drops to zero.
Fixes: ec44610fe2b8 ("fsnotify: count all objects with attached connectors")
Reported-by: Murphy Zhou <jencce.kernel@gmail.com>
Link: https://lore.kernel.org/linux-fsdevel/20210907063338.ycaw6wvhzrfsfdlp@xzhoux.usersys.redhat.com/
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Andre reported fw_devlink=on breaking OLPC XO-1.5 [1].
OLPC XO-1.5 is an X86 system that uses a mix of ACPI and OF to populate
devices. The root cause seems to be ISA devices not setting their fwnode
field. But trying to figure out how to fix that doesn't seem worth the
trouble because the OLPC devicetree is very sparse/limited and fw_devlink
only adds the links causing this issue. Considering that there aren't many
users of OF in an X86 system, simply fw_devlink DT support for X86.
[1] - https://lore.kernel.org/lkml/3c1f2473-92ad-bfc4-258e-a5a08ad73dd0@web.de/
Fixes: ea718c699055 ("Revert "Revert "driver core: Set fw_devlink=on by default""")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Cc: Andre Muller <andre.muller@web.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Andre Müller <andre.muller@web.de>
Link: https://lore.kernel.org/r/20210910011446.3208894-1-saravanak@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Using generated/compile.h triggered a full LKDTM rebuild with every
build. Avoid this by using the exported strings instead.
Fixes: b8661450bc7f ("lkdtm: Add kernel version to failure hints")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210901233406.2571643-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Frieder Schrempf
Philipp Zabel
Tim Harvey
Oleksij Rempel
Michael Walle
Heiko Thiery
Haibo Chen
Marcel Ziswiler
Fabio Estevam
Marek Vasut
Michal Vokáč
Linus Torvalds
Arnaldo Carvalho de Melo
Ian Rogers
Namhyung Kim
Adrian Hunter
Jisheng Zhang
Geert Uytterhoeven
Masahiro Yamada
Kefeng Wang
Heinrich Schuchardt
Thomas Gleixner
Sebastian Andrzej Siewior
Kim Phillips
Rob Herring
Amir Goldstein
Saravana Kannan
Kees Cook