| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
bcm2835's configuration registers can't be changed when a stream
is running, which means asymmetric configurations aren't supported.
Channel and rate symmetry are already enforced by constraints
but samplebits had been missed.
As hw_params doesn't check for symmetry constraints by itself
and just returns success if a stream is running this led to
situations where asymmetric configurations were seeming to
succeed but of course didn't work because the hardware wasn't
configured at all.
Fix this by adding the missing samplerate symmetry constraint.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sample rates are only restricted by the capabilities of the
clock driver, so use SNDRV_PCM_RATE_CONTINUOUS instead of
SNDRV_PCM_RATE_8000_192000.
Tests (eg with pcm5122) have shown that bcm2835 works fine
in 384kHz/32bit stereo mode, so change the maximum allowed
rate from 192kHz to 384kHz.
Signed-off-by: Matthias Reichl <hias@horus.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
bcm2835 supports arbitrary positioning of channel data within
a frame and thus is capable of supporting TDM modes. Since
the driver is limited to 2-channel operations only TDM setups
with exactly 2 active slots are supported.
Logical TDM slot numbering follows the usual convention:
For I2S-like modes, with a 50% duty-cycle frame clock,
slots 0, 2, ... are transmitted in the first half of a frame,
slots 1, 3, ... are transmitted in the second half.
For DSP modes slot numbering is ascending: 0, 1, 2, 3, ...
Channel position calculation has been refactored to use
TDM info and moved out of hw_params.
set_tdm_slot, set_bclk_ratio and hw_params now check more
strictly if the configuration is valid. Illegal configurations
like odd number of slots in I2S mode, data lengths exceeding
slot width or frame sizes larger than the hardware limit of
1024 are rejected. Also hw_params now properly checks for
errors from clk_set_rate.
Allowed PCM formats are already guarded by stream constraints,
thus the formats check in hw_params has been removed and
data_length is now retrieved via params_width().
Also standard functions like snd_soc_params_to_bclk are now
being used instead of manual calculations to make the code
more readable.
Special care has been taken to ensure that set_bclk_ratio works
as before. The bclk ratio is mapped to a 2-channel TDM config
with a slot width of half the ratio. In order to support odd ratios,
which can't be expressed via a TDM config, the ratio (frame length)
is stored and used by hw_params.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Before rendering starts, DMA driver copies full buffer valid data
to ACP SRAM for the first time, after that ACP SRAM to I2S
FIFO DMA will be initiated. After rendering first half of ACP SRAM,
IOC will be raised then Audio data will be copied from first half of
System Memory to first half of ACP SRAM. Similarly after rendering
second half of ACP SRAM, IOC will be raised then Audio Data will be
copied from second half of the System Memory to second half of the
ACP SRAM in ping-pong way till rendering stops.
Old design introducing latency issues resulting stutter sound observed
during playback.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Akshu Agrawal <Akshu.Agrawal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DSP modes are documented in the data sheet but not enabled in the driver.
The work-around already implemented for DA7218/9 is also required to
make sure the bit clock handling in DSP modes follows ASoC conventions.
Tested with ARD-AUDIO-DA7212 and Minnowmax Turbot boards
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While the current code was reporting to be able to work in master mode, it
failed to do so because the BCLK divider wasn't programmed, meaning that
the BCLK would run at the PLL's frequency no matter the sample rate.
It was obviously a bit too fast.
Add support to retrieve the divider to use, and set it. Since our PLL is
not always able to generate a perfect multiple of the sample rate, we'll
have to choose the closest divider that matches our setup.
Fixes: 36c684936fae ("ASoC: Add sun8i digital audio codec")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
|
|
ERROR: "__aeabi_uldivmod" [sound/soc/amd/snd-soc-acp-pcm.ko] undefined!
64-bit divides require special operations to avoid build errors on 32-bit
systems.
[Reword the commit message to make it clearer - Alex]
fixes: 61add8147942 (ASoC: amd: Report accurate hw_ptr during dma)
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/678919
Reviewed-by: Jason Clinton <jclinton@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/681618
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The binding states the reset GPIO property shall be named
"cirrus,gpio-nreset" and this is what the driver looks for,
but the example uses "gpio-reset". Fix this here.
Fixes: 3bb40619aca8 ("ASoC: cs42l56: bindings: sound: Add bindings for CS42L56 CODEC")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_dapm_kcontrol_codec() (= for Codec) will be removed soon.
This patch Component version of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_cache_sync() (= for Codec) will be removed soon.
This patch Component version of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_codec_xxx_bias_level() (= for Codec) will be removed soon.
This patch Component version of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current codec drivers are using snd_soc_read(). It will be replaced
into snd_soc_component_read(), but these 2 are using different style.
For example, it will be
- val = snd_soc_read(xxx, reg);
+ ret = snd_soc_component_read(xxx, reg, &val);
+ if (ret < 0) {
+ ...
+ }
To more smooth replace, let's add snd_soc_component_read32
which is copied from snd_soc_read()
- val = snd_soc_read(xxx, reg);
+ val = snd_soc_component_read32(xxx, reg);
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During failure, widgets in cvt_list and pin_list are not freed. So fix
the possible memory leak by freeing them when failure occurs.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pointers hdac_hdmi_pcm and hda_device_id can be NULL, so add check for
valid pointer to avoid NULL pointer dereference.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use snprintf instead of sprintf to shut the warning.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Module id is a property of firmware manifest and can vary between
platforms so use the uuid instead of module id for pins.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Modify skl_tplg_get_uuid() to copy just UUID rather than only
for module UUID and skl_tplg_fill_pin() to fill the pin info
which can include UUID token also.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In certain buggy BIOS acpi_evaluate_dsm() may not return the correct
NHLT table, so check the NHLT table header signature before accessing
it.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the loop that adds the uuid_module to the uuid_list list, allocated
memory is not properly freed in the error path free uuid_list whenever
any of the memory allocation in the loop fails to avoid memory leak.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pointer 'mconfig' returned from call to skl_tplg_fe_get_cpr_module() can
be NULL. So check for the valid pointer before dereferencing.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DSP expects channel map to be sent in the IPC for updown mixer module.
So add ch_map info in updown mixer module config.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DSP expects length of the coefficient for updown mixer module to be 8.
So fix the max coefficient length and since we are using default values
for coefficient select which is zero, we need not explicitly initialize
it.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This fixes the issue of driver not getting auto loaded with
MODULE_ALIAS.
find /sys/devices -name modalias -print0 | xargs -0 grep 'audio'
/sys/devices/pci0000:00/0000:00:01.0/acp_audio_dma.0.auto/modalias:platform:acp_audio_dma
TEST=boot and check for device in lsmod
[Removed yet more ChromeOS crap from the changelog -- broonie]
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Tested-by: Jason Clinton <jclinton@chromium.org>
Reviewed-by: Jason Clinton <jclinton@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current code had the condition backward when checking if the codec
should be running in slave or master mode.
Fix it, and make the comment a bit more readable.
Fixes: 36c684936fae ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
|
|
I ran into a build error with CONFIG_SND_SOC_INTEL_COMMON=m
and SND_SOC_INTEL_MACH=y:
ERROR: "snd_soc_acpi_intel_broadwell_machines" [sound/soc/intel/common/snd-soc-sst-acpi.ko] undefined!
ERROR: "snd_soc_acpi_intel_haswell_machines" [sound/soc/intel/common/snd-soc-sst-acpi.ko] undefined!
ERROR: "snd_soc_acpi_intel_cherrytrail_machines" [sound/soc/intel/atom/sst/snd-intel-sst-acpi.ko] undefined!
ERROR: "snd_soc_acpi_intel_baytrail_machines" [sound/soc/intel/atom/sst/snd-intel-sst-acpi.ko] undefined!
The problem here is that the sound/soc/intel/common/ directory
is then entered only for building modules, but the sst-acpi.o
never gets built since it depends on a built-in Kconfig symbol.
That configuration obviously makes no sense since all options
below SND_SOC_INTEL_MACH also depend on something else that
in turn depends on CONFIG_SND_SOC_INTEL_COMMON.
Adding a SND_SOC_INTEL_SST_TOPLEVEL dependency to SND_SOC_INTEL_MACH
solves the build error. I notice we can also consolidate the
'depends on SND_SOC_INTEL_MACH' lines by using an 'if' block to
simplify it further and make sure the configuration stays sane.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As pointed out by Pierre-Louis Bossart, the dependency I added
was broader than necessary, only Baytrail and Haswell/Broadwell
actually need it, the others don't.
At the same time, we have individual entries for the codecs
that all have the 'select' statement but now don't need it
any more.
Fixes: f7a88db6fffd ("ASoC: Intel: fix Kconfig dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using hw register to read transmitted byte count and report
accordingly the hw pointer.
TEST=
modprobe snd-soc-acp-pcm.ko
modprobe snd-soc-acp-rt5645.ko
aplay <file>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Akshu Agrawal <Akshu.Agrawal@amd.com>
Tested-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Jason Clinton <jclinton@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's difficult for me to handle upstream mail that ends up in my work
account and this was done outside of work anyway so replace my work
address with my usual address for upstream stuff.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
PTR_ERR(NULL) is success. Normally when a function returns both NULL
and error pointers, it means that NULL is not a error.
But, rsnd_dmaen_request_channel() returns NULL if requested resource
was failed.
Let's return -EIO if rsnd_dmaen_request_channel() was failed on
rsnd_dmaen_nolock_start().
This patch fixes commit edce5c496c6a ("ASoC: rsnd: Request/Release DMA
channel eachtime")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
There have been some cases where external tooling (e.g., kpatch-build)
creates a corrupt relocation which targets the wrong address. This is a
silent failure which can corrupt memory in unexpected places.
On x86, the bytes of data being overwritten by relocations are always
initialized to zero beforehand. Use that knowledge to add sanity checks
to detect such cases before they corrupt memory.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jeyu@kernel.org
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/37450d6c6225e54db107fba447ce9e56e5f758e9.1509713553.git.jpoimboe@redhat.com
[ Restructured the messages, as it's unclear whether the relocation or the target is corrupted. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This fixes the following warning with GCC 4.6:
mm/migrate.o: warning: objtool: migrate_misplaced_transhuge_page()+0x71: unreachable instruction
The problem is that the compiler merged identical annotate_unreachable()
inline asm blocks, resulting in a missing 'unreachable' annotation.
This problem happened before, and was partially fixed with:
3d1e236022cc ("objtool: Prevent GCC from merging annotate_unreachable()")
That commit tried to ensure that each instance of the
annotate_unreachable() inline asm statement has a unique label. It used
the __LINE__ macro to generate the label number. However, even the line
number isn't necessarily unique when used in an inline function with
multiple callers (in this case, __alloc_pages_node()'s use of
VM_BUG_ON).
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kbuild-all@01.org
Cc: tipbuild@zytor.com
Fixes: 3d1e236022cc ("objtool: Prevent GCC from merging annotate_unreachable()")
Link: http://lkml.kernel.org/r/20171103221941.cajpwszir7ujxyc4@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This reverts commit 43858b4f25cf0adc5c2ca9cf5ce5fdf2532941e5.
The reason I removed the leave_mm() calls in question is because the
heuristic wasn't needed after that patch. With the original version
of my PCID series, we never flushed a "lazy cpu" (i.e. a CPU running
kernel thread) due a flush on the loaded mm.
Unfortunately, that caused architectural issues, so now I've
reinstated these flushes on non-PCID systems in:
commit b956575bed91 ("x86/mm: Flush more aggressively in lazy TLB mode").
That, in turn, gives us a power management and occasionally
performance regression as compared to old kernels: a process that
goes into a deep idle state on a given CPU and gets its mm flushed
due to activity on a different CPU will wake the idle CPU.
Reinstate the old ugly heuristic: if a CPU goes into ACPI C3 or an
intel_idle state that is likely to cause a TLB flush gets its mm
switched to init_mm before going idle.
FWIW, this heuristic is lousy. Whether we should change CR3 before
idle isn't a good hint except insofar as the performance hit is a bit
lower if the TLB is getting flushed by the idle code anyway. What we
really want to know is whether we anticipate being idle long enough
that the mm is likely to be flushed before we wake up. This is more a
matter of the expected latency than the idle state that gets chosen.
This heuristic also completely fails on systems that don't know
whether the TLB will be flushed (e.g. AMD systems?). OTOH it may be a
bit obsolete anyway -- PCID systems don't presently benefit from this
heuristic at all.
We also shouldn't do this callback from innermost bit of the idle code
due to the RCU nastiness it causes. All the information need is
available before rcu_idle_enter() needs to happen.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 43858b4f25cf "x86/mm: Stop calling leave_mm() in idle code"
Link: http://lkml.kernel.org/r/c513bbd4e653747213e05bc7062de000bf0202a5.1509793738.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add my name to the list.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
add me to the list.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the SPDX license tags were added a number of tooling headers got out of
sync with their kernel variants, generating lots of build warnings.
Sync them:
- tools/arch/x86/include/asm/disabled-features.h,
tools/arch/x86/include/asm/required-features.h,
tools/include/linux/hash.h:
Remove the SPDX tag where the kernel version does not have it.
- tools/include/asm-generic/bitops/__fls.h,
tools/include/asm-generic/bitops/arch_hweight.h,
tools/include/asm-generic/bitops/const_hweight.h,
tools/include/asm-generic/bitops/fls.h,
tools/include/asm-generic/bitops/fls64.h,
tools/include/uapi/asm-generic/ioctls.h,
tools/include/uapi/asm-generic/mman-common.h,
tools/include/uapi/sound/asound.h,
tools/include/uapi/linux/kvm.h,
tools/include/uapi/linux/perf_event.h,
tools/include/uapi/linux/sched.h,
tools/include/uapi/linux/vhost.h,
tools/include/uapi/sound/asound.h:
Add the SPDX tag of the respective kernel header.
- tools/include/uapi/linux/bpf_common.h,
tools/include/uapi/linux/fcntl.h,
tools/include/uapi/linux/hw_breakpoint.h,
tools/include/uapi/linux/mman.h,
tools/include/uapi/linux/stat.h,
Change the tag to the kernel header version:
-/* SPDX-License-Identifier: GPL-2.0 */
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
Also sync other header details:
- include/uapi/sound/asound.h:
Fix pointless end of line whitespace noise the header grew in this cycle.
- tools/arch/x86/lib/memcpy_64.S:
Sync the code and add tools/include/asm/export.h with dummy wrappers
to support building the kernel side code in a tooling header environment.
- tools/include/uapi/asm-generic/mman.h,
tools/include/uapi/linux/bpf.h:
Sync other details that don't impact tooling's use of the ABIs.
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This fixes the following warning:
warning: objtool: x86 instruction decoder differs from kernel
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/013315a808ccf5580abc293808827c8e2b5e1354.1509719152.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Sync events are sent by sparse_keymap_report_entry for normal KEY_*
events, and are generated by several drivers after generating
SW_* events, so sparse_keymap_report_entry should do the same.
Without the sync, events are accumulated in the kernel.
Currently, no driver uses sparse-keymap for SW_* events, but
it is required for the intel-vbtn platform driver to generate
SW_TABLET_MODE events.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If INPUT_PROP_DIRECT is set, userspace doesn't have to fall back to old
ways of identifying touchscreen devices. Let's add it.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
set_state_oneshot_stopped() is called by the clkevt core, when the
next event is required at an expiry time of 'KTIME_MAX'. This normally
happens with NO_HZ_{IDLE|FULL} in both LOWRES/HIGHRES modes.
This patch makes the clockevent device to stop on such an event, to
avoid spurious interrupts, as explained by: commit 8fff52fd5093
("clockevents: Introduce CLOCK_EVT_STATE_ONESHOT_STOPPED state").
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
|
|
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 890da9cf0983 (Revert "x86: do not use cpufreq_quick_get() for
/proc/cpuinfo "cpu MHz"") is not sufficient to restore the previous
behavior of "cpu MHz" in /proc/cpuinfo on x86 due to some changes
made after the commit it has reverted.
To address this, make the code in question use arch_freq_get_on_cpu()
which also is used by cpufreq for reporting the current frequency of
CPUs and since that function doesn't really depend on cpufreq in any
way, drop the CONFIG_CPU_FREQ dependency for the object file
containing it.
Also refactor arch_freq_get_on_cpu() somewhat to avoid IPIs and
return cached values right away if it is called very often over a
short time (to prevent user space from triggering IPI storms through
it).
Fixes: 890da9cf0983 (Revert "x86: do not use cpufreq_quick_get() for /proc/cpuinfo "cpu MHz"")
Cc: stable@kernel.org # 4.13 - together with 890da9cf0983
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
One page may store a set of entries of the sis->swap_map
(swap_info_struct->swap_map) in multiple swap clusters.
If some of the entries has sis->swap_map[offset] > SWAP_MAP_MAX,
multiple pages will be used to store the set of entries of the
sis->swap_map. And the pages are linked with page->lru. This is called
swap count continuation. To access the pages which store the set of
entries of the sis->swap_map simultaneously, previously, sis->lock is
used. But to improve the scalability of __swap_duplicate(), swap
cluster lock may be used in swap_count_continued() now. This may race
with add_swap_count_continuation() which operates on a nearby swap
cluster, in which the sis->swap_map entries are stored in the same page.
The race can cause wrong swap count in practice, thus cause unfreeable
swap entries or software lockup, etc.
To fix the race, a new spin lock called cont_lock is added to struct
swap_info_struct to protect the swap count continuation page list. This
is a lock at the swap device level, so the scalability isn't very well.
But it is still much better than the original sis->lock, because it is
only acquired/released when swap count continuation is used. Which is
considered rare in practice. If it turns out that the scalability
becomes an issue for some workloads, we can split the lock into some
more fine grained locks.
Link: http://lkml.kernel.org/r/20171017081320.28133-1-ying.huang@intel.com
Fixes: 235b62176712 ("mm/swap: add cluster lock")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [4.11+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to deposit pre-allocated PTE page table when a PMD migration
entry is copied in copy_huge_pmd(). Otherwise, we will leak the
pre-allocated page and cause a NULL pointer dereference later in
zap_huge_pmd().
The missing counters during PMD migration entry copy process are added
as well.
The bug report is here: https://lkml.org/lkml/2017/10/29/214
Link: http://lkml.kernel.org/r/20171030144636.4836-1-zi.yan@sent.com
Fixes: 84c3fc4e9c563 ("mm: thp: check pmd migration entry in common path")
Signed-off-by: Zi Yan <zi.yan@cs.rutgers.edu>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a follow-up to commit 57ddfdaa9a72 ("initramfs: fix disabling of
initramfs (and its compression)"). This particular commit fixed the use
case where we build the kernel with an initramfs with no compression,
and then we build the kernel with no initramfs.
Now this still left us with the same case as described here:
http://lkml.kernel.org/r/20170521033337.6197-1-f.fainelli@gmail.com
not working with initramfs compression. This can be seen by the
following steps/timestamps:
https://www.spinics.net/lists/kernel/msg2598153.html
.initramfs_data.cpio.gz.cmd is correct:
cmd_usr/initramfs_data.cpio.gz := /bin/bash
./scripts/gen_initramfs_list.sh -o usr/initramfs_data.cpio.gz -u 1000 -g 1000 /home/fainelli/work/uclinux-rootfs/romfs /home/fainelli/work/uclinux-rootfs/misc/initramfs.dev
and was generated the first time we did generate the gzip initramfs, so
the command has not changed, nor its arguments, so we just don't call
it, no initramfs cpio is re-generated as a consequence.
The fix for this problem is just to properly keep track of the
.initramfs_cpio_data.d file by suffixing it with the compression
extension. This takes care of properly tracking dependencies such that
the initramfs get (re)generated any time files are added/deleted etc.
Link: http://lkml.kernel.org/r/20170930033936.6722-1-f.fainelli@gmail.com
Fixes: db2aa7fd15e8 ("initramfs: allow again choice of the embedded initramfs compression algorithm")
Fixes: 9e3596b0c653 ("kbuild: initramfs cleanup, set target from Kconfig")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: "Francisco Blas Izquierdo Riera (klondike)" <klondike@xiscosoft.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calling madvise(MADV_HWPOISON) on a hugetlbfs page will result in bad
(negative) reserved huge page counts. This may not happen immediately,
but may happen later when the underlying file is removed or filesystem
unmounted. For example:
AnonHugePages: 0 kB
ShmemHugePages: 0 kB
HugePages_Total: 1
HugePages_Free: 0
HugePages_Rsvd: 18446744073709551615
HugePages_Surp: 0
Hugepagesize: 2048 kB
In routine hugetlbfs_error_remove_page(), hugetlb_fix_reserve_counts is
called after remove_huge_page. hugetlb_fix_reserve_counts is designed
to only be called/used only if a failure is returned from
hugetlb_unreserve_pages. Therefore, call hugetlb_unreserve_pages as
required and only call hugetlb_fix_reserve_counts in the unlikely event
that hugetlb_unreserve_pages returns an error.
Link: http://lkml.kernel.org/r/20171019230007.17043-2-mike.kravetz@oracle.com
Fixes: 78bb920344b8 ("mm: hwpoison: dissolve in-use hugepage in unrecoverable memory error")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The first cluster group descriptor is not stored at the start of the
group but at an offset from the start. We need to take this into
account while doing fstrim on the first cluster group. Otherwise we
will wrongly start fstrim a few blocks after the desired start block and
the range can cross over into the next cluster group and zero out the
group descriptor there. This can cause filesytem corruption that cannot
be fixed by fsck.
Link: http://lkml.kernel.org/r/1507835579-7308-1-git-send-email-ashish.samant@oracle.com
Signed-off-by: Ashish Samant <ashish.samant@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the pagetable is walked in the implementation of /proc/<pid>/pagemap,
pmd_soft_dirty() is used for both the PMD huge page map and the PMD
migration entries. That is wrong, pmd_swp_soft_dirty() should be used
for the PMD migration entries instead because the different page table
entry flag is used.
As a result, /proc/pid/pagemap may report incorrect soft dirty information
for PMD migration entries.
Link: http://lkml.kernel.org/r/20171017081818.31795-1-ying.huang@intel.com
Fixes: 84c3fc4e9c56 ("mm: thp: check pmd migration entry in common path")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Daniel Colascione <dancol@google.com>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This oops:
kernel BUG at fs/hugetlbfs/inode.c:484!
RIP: remove_inode_hugepages+0x3d0/0x410
Call Trace:
hugetlbfs_setattr+0xd9/0x130
notify_change+0x292/0x410
do_truncate+0x65/0xa0
do_sys_ftruncate.constprop.3+0x11a/0x180
SyS_ftruncate+0xe/0x10
tracesys+0xd9/0xde
was caused by the lack of i_size check in hugetlb_mcopy_atomic_pte.
mmap() can still succeed beyond the end of the i_size after vmtruncate
zapped vmas in those ranges, but the faults must not succeed, and that
includes UFFDIO_COPY.
We could differentiate the retval to userland to represent a SIGBUS like
a page fault would do (vs SIGSEGV), but it doesn't seem very useful and
we'd need to pick a random retval as there's no meaningful syscall
retval that would differentiate from SIGSEGV and SIGBUS, there's just
-EFAULT.
Link: http://lkml.kernel.org/r/20171016223914.2421-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add my name to the list.
Signed-off-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Matthias Reichl
Vijendar Mukunda
Pierre-Louis Bossart
Maxime Ripard
Guenter Roeck
Andrew F. Davis
Kuninori Morimoto
Subhransu S. Prusty
Sriram Periyasamy
Pankaj Bharadiya
Guneshwor Singh
Akshu Agrawal
Arnd Bergmann
Mark Brown
Linus Torvalds
Josh Poimboeuf
Andy Lutomirski
Frank Rowand
Willy Tarreau
Ingo Molnar
Stefan Brüns
Martin Kepplinger
Chris Metcalf
Paul Burton
Rafael J. Wysocki
Huang Ying
Zi Yan
Florian Fainelli
Mike Kravetz
Ashish Samant
Andrea Arcangeli
Bird, Timothy