| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Don't populate the const read-only array 'req' on the stack but instead
make it static. Makes the object code smaller by over 40 bytes:
Before:
text data bss dec hex filename
8497 3408 128 12033 2f01 linux/drivers/bluetooth/bpa10x.o
After:
text data bss dec hex filename
8366 3496 128 11990 2ed6 linux/drivers/bluetooth/bpa10x.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Commit 27378f4c1b92 ("Bluetooth: Avoid WARN splat due to missing
GPIOLIB") amended Kconfig to select GPIOLIB if BT_HCIUART_NOKIA,
BT_HCIUART_INTEL or BT_HCIUART_BCM is enabled since all three drivers
require it to function.
The diagnosis was correct but the treatment was not. As stated in
Documentation/gpio/consumer.txt:
Guidelines for GPIOs consumers
==============================
Drivers that can't work without standard GPIO calls should have
Kconfig entries that depend on GPIOLIB.
^^^^^^^^^
Fix it.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When the hci support is built-in, but mvmem is a loadable module, we
get a link failure:
drivers/bluetooth/hci_ll.o: In function `hci_ti_probe':
hci_ll.c:(.text+0x226): undefined reference to `nvmem_cell_get'
hci_ll.c:(.text+0x238): undefined reference to `nvmem_cell_read'
hci_ll.c:(.text+0x244): undefined reference to `nvmem_cell_put'
This adds another Kconfig dependency to enforce valid configurations.
Fixes: 0e58d0cdb3eb ("Bluetooth: hci_ll: Add optional nvmem BD address source")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Device 0cf3:e010 is one of the QCA ROME family.
T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=e010 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This reverts commit fd865802c66bc451dc515ed89360f84376ce1a56.
This commit causes a regression on some QCA ROME chips. The USB device
reset happens in btusb_open(), hence firmware loading gets interrupted.
Furthermore, this commit stops working after commit
("a0085f2510e8976614ad8f766b209448b385492f Bluetooth: btusb: driver to
enable the usb-wakeup feature"). Reset-resume quirk only gets enabled in
btusb_suspend() when it's not a wakeup source.
If we really want to reset the USB device, we need to do it before
btusb_open(). Let's handle it in drivers/usb/core/quirks.c.
Cc: stable@vger.kernel.org
Cc: Leif Liddy <leif.linux@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Daniel Drake <drake@endlessm.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This driver seeks to force the Bluetooth device on for the duration of
5 seconds when the Bluetooth device has woken the host and after a
complete packet has been received. It does that by calling:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
The same can be achieved more succinctly with:
pm_request_resume();
That's because after runtime resuming the device, rpm_resume() invokes
pm_runtime_mark_last_busy() followed by rpm_idle(), which will cause
the device to be suspended after expiration of the autosuspend_delay.
No functional change intended.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Loading hci_bcm with CONFIG_GPIOLIB=n results in the following splat
when calling gpiod_to_irq() from bcm_get_resources():
WARNING: CPU: 0 PID: 1006 at ./include/linux/gpio/consumer.h:450 bcm_get_resources+0x50/0x80
CPU: 0 PID: 1006 Comm: kworker/u8:4 Tainted: G A 4.15.0-rc4custom+ #4
Hardware name: Apple Inc. MacBook8,1/Mac-BE0E8AC46FE800CC, BIOS MB81.88Z.0168.B00.1708080033 08/08/2017
Call Trace:
bcm_serdev_probe+0x8b/0xc0
driver_probe_device+0x202/0x310
__driver_attach+0x85/0x90
? driver_probe_device+0x310/0x310
bus_for_each_dev+0x57/0x80
async_run_entry_fn+0x2c/0xd0
process_one_work+0x1d2/0x3d0
worker_thread+0x26/0x3c0
? process_one_work+0x3d0/0x3d0
kthread+0x10c/0x130
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x1f/0x30
We could call gpiod_to_irq() only if IS_ENABLED(CONFIG_GPIOLIB) but
without GPIOLIB, the driver's power saving features can't be used,
so selecting GPIOLIB seems more appropriate.
The same issue is present in hci_intel.c and hci_nokia.c, fix those up
as well.
Reported-by: Max Shavrick <mxms@me.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the 04ca:3015 (from a QCA9377 board) Bluetooth device
to the btusb blacklist and makes the kernel use the btqca module
instead of btusb. The patch is necessary because, without it the
04ca:3015 device defaults to using the btusb driver, which makes the
WIFI side of the QCA9377 board unusable (obtains 0 MBps in speedtest,
when the 04ca:3015 bluetooth is used with an audio headset).
/sys/kernel/debug/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3015 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Ioan Moldovan <ioan.moldovan1999@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
In case of tx clean up, we set '-1' as budget. This means clean up until
wq is empty or till (1 << 32) pkts are cleaned. Under heavy load this
will run for long time and cause
"watchdog: BUG: soft lockup - CPU#25 stuck for 21s!" warning.
This patch sets wq clean up budget to 256.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ASSERT_RTNL() macro is actual open-coded variant of WARN_ONCE() with
two exceptions. First, it prints stack for multiple hits and not only
once as WARN_ONCE() does. Second, the user can disable prints of
WARN_ONCE by setting CONFIG_BUG to N.
The multiple prints of dump stack are actually not needed, because calls
without rtnl lock are programming errors and user can't do anything
about them except to complain to the mailing list after first occurrence
of such failure.
The user who disabled BUG/WARN prints did it explicitly because by default
in upstream kernel and distributions this option is enabled. It means
that user doesn't want to see prints about missing locks too.
This patch replaces open-coded variant in favor of already existing
macro and change error prints to be once only.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove superfluous pin setup to get out of accessing invalid I/O pin
registers because the way for pin configuring tends to be different from
various SoCs and thus it should be better being managed and controlled by
the pinctrl driver which MT7622 already can support.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The property "mediatek,pctl" is only required for SoCs such as MT2701 and
MT7623, so adding a few words for stating the condition.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The batman-adv unicast packets contain a full layer 2 frame in encapsulated
form. The flow dissector must therefore be able to parse the batman-adv
unicast header to reach the layer 2+3 information.
+--------------------+
| ip(v6)hdr |
+--------------------+
| inner ethhdr |
+--------------------+
| batadv unicast hdr |
+--------------------+
| outer ethhdr |
+--------------------+
The obtained information from the upper layer can then be used by RPS to
schedule the processing on separate cores. This allows better distribution
of multiple flows from the same neighbor to different cores.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The uapi headers use the __u8/__u16/... version of the fixed width types
instead of u8/u16/... The use of the latter must be avoided before
packet.h is copied to include/uapi/linux/.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BIT(x) macro is no longer available for uapi headers because it is
defined outside of it (linux/bitops.h). The use of it must therefore be
avoided and replaced by an appropriate other representation.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The headers used by packet.h should also be included by it directly. main.h
is currently dealing with it in batman-adv, but this will no longer work
when this header is moved to include/uapi/linux/.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the Linux driver doesn't use CTPIO ('cut-through programmed I/O'),
other drivers on the same port might, so if we're responsible for
reporting per-port stats we need to include the CTPIO stats.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no explicit capability bit, so we just condition them on having
efx->num_mac_stats >= MC_CMD_MAC_NSTATS_V2.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Medford2 NICs support more than MC_CMD_MAC_NSTATS stats, and report the new
count in a field of MC_CMD_GET_CAPABILITIES_V4. This also means that the
end generation count moves (it is, as before, the last 64 bits of the DMA
buffer, but that is no longer MC_CMD_MAC_GENERATION_END).
So read num_mac_stats from the GET_CAPABILITIES response, if present;
otherwise assume MC_CMD_MAC_NSTATS; and always use num_mac_stats - 1 rather
than MC_CMD_MAC_GENERATION_END.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add device id's 0x50ac, 0x6087 for T5 and T6 cards
respectively.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of custom hex_dump_to_buffer().
The output is slightly changed, i.e. each byte followed by white space.
Note, we don't use print_hex_dump() here since the original code uses
nedev_dbg().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Attaching more than one PHY to phylink is bad news, as we store a
pointer to the PHY in a single location. Error out if more than one
PHY is attempted to be attached.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_copy_ubufs creates a private copy of frags[] to release its hold
on user frags, then calls uarg->callback to notify the owner.
Call uarg->callback even when no frags exist. This edge case can
happen when zerocopy_sg_from_iter finds enough room in skb_headlen
to copy all the data.
Fixes: 3ece782693c4 ("sock: skb_copy_ubufs support for compound pages")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call skb_zerocopy_clone after skb_orphan_frags, to avoid duplicate
calls to skb_uarg(skb)->callback for the same data.
skb_zerocopy_clone associates skb_shinfo(skb)->uarg from frag_skb
with each segment. This is only safe for uargs that do refcounting,
which is those that pass skb_orphan_frags without dropping their
shared frags. For others, skb_orphan_frags drops the user frags and
sets the uarg to NULL, after which sock_zerocopy_clone has no effect.
Qemu hangs were reported due to duplicate vhost_net_zerocopy_callback
calls for the same data causing the vhost_net_ubuf_ref_>refcount to
drop below zero.
Link: http://lkml.kernel.org/r/<CAF=yD-LWyCD4Y0aJ9O0e_CHLR+3JOeKicRRTEVCPxgw4XOcqGQ@mail.gmail.com>
Fixes: 1f8b977ab32d ("sock: enable MSG_ZEROCOPY")
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Reported-by: David Hill <dhill@redhat.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RGMII spec allows compliance for devices that implement an internal
delay on TXC and/or RXC inside the transmitter. This patch adds the
necessary RGMII_[RX|TX]ID mode code to handle such PHYs with the
emac driver.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ibm_emac driver predates the PHY_INTERFACE_MODE_*
enums by a few years.
And while the driver has been retrofitted to use the PHYLIB,
the old definitions have stuck around to this day.
This patch replaces all occurences of PHY_MODE_* with
the respective equivalent PHY_INTERFACE_MODE_* enum.
And finally, it purges the old macros for good.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_modes() in the common phy.h already defines the same phy mode
names in lower case. The deleted rgmii_mode_name() is used only
in one place and for a "notice-level" printk. Hence, it will not
be missed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl.ip6.auto_flowlabels is default 1. In our hosts, we set it to 2.
If sockopt doesn't set autoflowlabel, outcome packets from the hosts are
supposed to not include flowlabel. This is true for normal packet, but
not for reset packet.
The reason is ipv6_pinfo.autoflowlabel is set in sock creation. Later if
we change sysctl.ip6.auto_flowlabels, the ipv6_pinfo.autoflowlabel isn't
changed, so the sock will keep the old behavior in terms of auto
flowlabel. Reset packet is suffering from this problem, because reset
packet is sent from a special control socket, which is created at boot
time. Since sysctl.ipv6.auto_flowlabels is 1 by default, the control
socket will always have its ipv6_pinfo.autoflowlabel set, even after
user set sysctl.ipv6.auto_flowlabels to 1, so reset packset will always
have flowlabel. Normal sock created before sysctl setting suffers from
the same issue. We can't even turn off autoflowlabel unless we kill all
socks in the hosts.
To fix this, if IPV6_AUTOFLOWLABEL sockopt is used, we use the
autoflowlabel setting from user, otherwise we always call
ip6_default_np_autolabel() which has the new settings of sysctl.
Note, this changes behavior a little bit. Before commit 42240901f7c4
(ipv6: Implement different admin modes for automatic flow labels), the
autoflowlabel behavior of a sock isn't sticky, eg, if sysctl changes,
existing connection will change autoflowlabel behavior. After that
commit, autoflowlabel behavior is sticky in the whole life of the sock.
With this patch, the behavior isn't sticky again.
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <tom@quantonium.net>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_vlan_pop() expects skb->protocol to be a valid TPID for double
tagged frames. So set skb->protocol to the TPID and let skb_vlan_pop()
shift the true ethertype into position for us.
Fixes: 5108bbaddc37 ("openvswitch: add processing of L3 packets")
Signed-off-by: Eric Garver <e@erig.me>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for the drr qdisc implementation by
adding NL_SET_ERR_MSG in validation of user input.
Also it serves to illustrate a use case of how the infrastructure ops
api changes are to be used by individual qdiscs.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for the cbs qdisc implementation by
adding NL_SET_ERR_MSG in validation of user input.
Also it serves to illustrate a use case of how the infrastructure ops
api changes are to be used by individual qdiscs.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for the cbq qdisc implementation by
adding NL_SET_ERR_MSG in validation of user input.
Also it serves to illustrate a use case of how the infrastructure ops
api changes are to be used by individual qdiscs.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for the function qdisc_create_dflt which is
a common used function in the tc subsystem. Callers which are interested
in the receiving error can assign extack to get a more detailed
information why qdisc_create_dflt failed. The function qdisc_create_dflt
will also call an init callback which can fail by any per-qdisc specific
handling.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for the function qdisc_alloc which is
a common used function in the tc subsystem. Callers which are interested
in the receiving error can assign extack to get a more detailed
information why qdisc_alloc failed.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for the function tcf_block_get which is
a common used function in the tc subsystem. Callers which are interested
in the receiving error can assign extack to get a more detailed
information why tcf_block_get failed.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for the function qdisc_get_rtab which is
a common used function in the tc subsystem. Callers which are interested
in the receiving error can assign extack to get a more detailed
information why qdisc_get_rtab failed.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for graft callback to prepare per-qdisc
specific changes for extack.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for block callback to prepare per-qdisc
specific changes for extack.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for class change callback api. This prepares
to handle extack support inside each specific class implementation.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for change callback for qdisc ops
structtur to prepare per-qdisc specific changes for extack.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for init callback to prepare per-qdisc
specific changes for extack.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack support for generic qdisc handling. The extack
will be set deeper to each called function which is not part of netdev
core api.
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix checkpatch issues for upcomming patches according to the
sched api file. It changes mostly how to check on null pointer.
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a0747a859ef6d3cc5b6cd50eb694499b78dd0025.
It breaks some booting for some users, and more than a week
into this, there's still no good fix. Revert this commit
for now until a solution has been found.
Reported-by: Laura Abbott <labbott@redhat.com>
Reported-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, parameters such as oif and source address are not taken into
account during fibmatch lookup. Example (IPv4 for reference) before
patch:
$ ip -4 route show
192.0.2.0/24 dev dummy0 proto kernel scope link src 192.0.2.1
198.51.100.0/24 dev dummy1 proto kernel scope link src 198.51.100.1
$ ip -6 route show
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy0 proto kernel metric 256 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
$ ip -4 route get fibmatch 192.0.2.2 oif dummy0
192.0.2.0/24 dev dummy0 proto kernel scope link src 192.0.2.1
$ ip -4 route get fibmatch 192.0.2.2 oif dummy1
RTNETLINK answers: No route to host
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy0
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy1
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
After:
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy0
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy1
RTNETLINK answers: Network is unreachable
The problem stems from the fact that the necessary route lookup flags
are not set based on these parameters.
Instead of duplicating the same logic for fibmatch, we can simply
resolve the original route from its copy and dump it instead.
Fixes: 18c3a61c4264 ("net: ipv6: RTM_GETROUTE: return matched fib result when requested")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sort the fields returned by specifying '-f help' on the command line.
While at it, simplify the code a bit, indent the output and eliminate an
extra blank line at the beginning.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
rsm_load_state_64() and rsm_enter_protected_mode() load CR3, then
CR4 & ~PCIDE, then CR0, then CR4.
However, setting CR4.PCIDE fails if CR3[11:0] != 0. It's probably easier
in the long run to replace rsm_enter_protected_mode() with an emulator
callback that sets all the special registers (like KVM_SET_SREGS would
do). For now, set the PCID field of CR3 only after CR4.PCIDE is 1.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Fixes: 660a5d517aaab9187f93854425c4c63f4a09195c
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Do not allow root to convert valid pointers into unknown scalars.
In particular disallow:
ptr &= reg
ptr <<= reg
ptr += ptr
and explicitly allow:
ptr -= ptr
since pkt_end - pkt == length
1.
This minimizes amount of address leaks root can do.
In the future may need to further tighten the leaks with kptr_restrict.
2.
If program has such pointer math it's likely a user mistake and
when verifier complains about it right away instead of many instructions
later on invalid memory access it's easier for users to fix their progs.
3.
when register holding a pointer cannot change to scalar it allows JITs to
optimize better. Like 32-bit archs could use single register for pointers
instead of a pair required to hold 64-bit scalars.
4.
reduces architecture dependent behavior. Since code:
r1 = r10;
r1 &= 0xff;
if (r1 ...)
will behave differently arm64 vs x64 and offloaded vs native.
A significant chunk of ptr mangling was allowed by
commit f1174f77b50c ("bpf/verifier: rework value tracking")
yet some of it was allowed even earlier.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
Colin Ian King
Lukas Wunner
Arnd Bergmann
AceLan Kao
Kai-Heng Feng
Ioan Moldovan
Govindarajulu Varadarajan
Leon Romanovsky
Sean Wang
Sven Eckelmann
Bert Kenward
Edward Cree
Ganesh Goudar
Jie Deng
Russell King
Willem de Bruijn
Christian Lamparter
Shaohua Li
Eric Garver
Alexander Aring
Jens Axboe
Ido Schimmel
Stefan Raspl
Paolo Bonzini
Alexei Starovoitov