Age | Commit message (Collapse) | Author | Files | Lines |
|
This commit replaces my company's email address with a stable private
address.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The can_rx_unregister() can be called from NAPI (soft IRQ) context, at least
by j1939 stack. This leads to potential dead lock with &net->can.rcvlists_lock
called from can_rx_register:
===============================================================================
WARNING: inconsistent lock state
4.19.0-20181029-1-g3e67f95ba0d3 #3 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
testj1939/224 [HC0[0]:SC1[1]:HE1:SE0] takes:
1ad0fda3 (&(&net->can.rcvlists_lock)->rlock){+.?.}, at: can_rx_unregister+0x4c/0x1ac
{SOFTIRQ-ON-W} state was registered at:
lock_acquire+0xd0/0x1f4
_raw_spin_lock+0x30/0x40
can_rx_register+0x5c/0x14c
j1939_netdev_start+0xdc/0x1f8
j1939_sk_bind+0x18c/0x1c8
__sys_bind+0x70/0xb0
sys_bind+0x10/0x14
ret_fast_syscall+0x0/0x28
0xbedc9b64
irq event stamp: 2440
hardirqs last enabled at (2440): [<c01302c0>] __local_bh_enable_ip+0xac/0x184
hardirqs last disabled at (2439): [<c0130274>] __local_bh_enable_ip+0x60/0x184
softirqs last enabled at (2412): [<c08b0bf4>] release_sock+0x84/0xa4
softirqs last disabled at (2415): [<c013055c>] irq_exit+0x100/0x1b0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&net->can.rcvlists_lock)->rlock);
<Interrupt>
lock(&(&net->can.rcvlists_lock)->rlock);
*** DEADLOCK ***
2 locks held by testj1939/224:
#0: 168eb13b (rcu_read_lock){....}, at: netif_receive_skb_internal+0x3c/0x350
#1: 168eb13b (rcu_read_lock){....}, at: can_receive+0x88/0x1c0
===============================================================================
To avoid this situation, we should use spin_lock_bh() instead of spin_lock().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since using the "struct can_ml_priv" for the per device "struct
dev_rcv_lists" the call can_dev_rcv_lists_find() cannot fail anymore.
This patch simplifies af_can by removing the NULL pointer checks from
the dev_rcv_lists returned by can_dev_rcv_lists_find().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes the old method of allocating the per device protocol
specific memory via a netdevice_notifier. This had the drawback, that
the allocation can fail, leading to a lot of null pointer checks in the
code. This also makes the live cycle management of this memory quite
complicated.
This patch switches from the allocating the struct can_dev_rcv_lists in
a NETDEV_REGISTER call to using the dev->ml_priv, which is allocated by
the driver since the previous patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch introduces the CAN midlayer private structure ("struct
can_ml_priv") which should be used to hold protocol specific per device
data structures. For now it's only member is "struct can_dev_rcv_lists".
The CAN midlayer private is allocated via alloc_netdev()'s private and
assigned to "struct net_device::ml_priv" during device creation. This is
done transparently for CAN drivers using alloc_candev(). The slcan, vcan
and vxcan drivers which are not using alloc_candev() have been adopted
manually. The memory layout of the netdev_priv allocated via
alloc_candev() will looke like this:
+-------------------------+
| driver's priv |
+-------------------------+
| struct can_ml_priv |
+-------------------------+
| array of struct sk_buff |
+-------------------------+
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The networking core takes care and unregisters every network device in
a namespace before calling the can_pernet_exit() hook. This patch
removes the unneeded cleanup.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Suggested-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch replaces an open coded max by the proper kernel define max().
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch gives the variables holding the CAN receiver and the receiver
list a better name by renaming them from "r to "rcv" and "rl" to
"recv_list".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch add the commonly used prefix "can_" to the find_dev_rcv_lists()
function and moves the "find" to the end, as the function returns a struct
can_dev_rcv_list. This improves the overall readability of the code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch add the commonly used prefix "can_" to the find_rcv_list()
function and add the "find" to the end, as the function returns a struct
rcv_list. This improves the overall readability of the code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch gives the variables holding the CAN per device receive filter lists
a better name by renaming them from "d" to "dev_rcv_lists".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch gives the variables holding the CAN receive filter lists a
better name by renaming them from "d" to "dev_rcv_lists".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch improves the code reability by removing the redundant "can_"
prefix from the members of struct netns_can (as the struct netns_can itself
is the member "can" of the struct net.)
The conversion is done with:
sed -i \
-e "s/struct can_dev_rcv_lists \*can_rx_alldev_list;/struct can_dev_rcv_lists *rx_alldev_list;/" \
-e "s/spinlock_t can_rcvlists_lock;/spinlock_t rcvlists_lock;/" \
-e "s/struct timer_list can_stattimer;/struct timer_list stattimer; /" \
-e "s/can\.can_rx_alldev_list/can.rx_alldev_list/g" \
-e "s/can\.can_rcvlists_lock/can.rcvlists_lock/g" \
-e "s/can\.can_stattimer/can.stattimer/g" \
include/net/netns/can.h \
net/can/*.[ch]
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch rename the variables holding the CAN statistics (can_stats
and can_pstats) to pkg_stats and rcv_lists_stats which reflect better
their meaning.
The conversion is done with:
sed -i \
-e "s/can_stats\([^_]\)/pkg_stats\1/g" \
-e "s/can_pstats/rcv_lists_stats/g" \
net/can/proc.c
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch rename the variables holding the CAN statistics (can_stats
and can_pstats) to pkg_stats and rcv_lists_stats which reflect better
their meaning.
The conversion is done with:
sed -i \
-e "s/can_stats\([^_]\)/pkg_stats\1/g" \
-e "s/can_pstats/rcv_lists_stats/g" \
net/can/af_can.c
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch gives the members of the struct netns_can that are holding
the statistics a sensible name, by renaming struct netns_can::can_stats
into struct netns_can::pkg_stats and struct netns_can::can_pstats into
struct netns_can::rcv_lists_stats.
The conversion is done with:
sed -i \
-e "s:\(struct[^*]*\*\)can_stats;.*:\1pkg_stats;:" \
-e "s:\(struct[^*]*\*\)can_pstats;.*:\1rcv_lists_stats;:" \
-e "s/can\.can_stats/can.pkg_stats/g" \
-e "s/can\.can_pstats/can.rcv_lists_stats/g" \
net/can/*.[ch] \
include/net/netns/can.h
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch renames both "struct s_stats" and "struct s_pstats", to
"struct can_pkg_stats" and "struct can_rcv_lists_stats" to better
reflect their meaning and improve code readability.
The conversion is done with:
sed -i \
-e "s/struct s_stats/struct can_pkg_stats/g" \
-e "s/struct s_pstats/struct can_rcv_lists_stats/g" \
net/can/*.[ch] \
include/net/netns/can.h
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently if the VF adds a VLAN, VLAN pruning will be enabled for that VSI.
Also, when a VLAN gets deleted it will disable VLAN pruning even if other
VLAN(s) exists for the VF. Fix this by only disabling VLAN pruning on the
VF VSI when removing the last VF (i.e. vf->num_vlan == 0).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove code that enables DCB in initialization when SW LLDP is
activated. DCB flag is set or reset before in ice_init_pf_dcb
based on number of TCs. So there is not need to overwrite it.
Setting DCB without checking number of TCs can cause communication
problems with other cards. Host card sends packet with VLAN priority
tag, but client card doesn't strip this tag and ping doesn't work.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is currently a check in get_ndo_stats that
returns before updating stats if the VSI is down
or there are no Tx or Rx queues. This causes the
netdev to report zero stats with the netdev is down.
Remove the check so that the behavior of reporting
stats is the same as it was in IXGBE.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The call to ice_dis_vsi_txq() acts as the notification to the firmware
that the VF is being reset. Because of this, we need to make this call
every time we reset, regardless of whatever else we do to stop the Tx
queues.
Without this change, VF resets would fail to complete on interfaces that
were up and running.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the init path for DCB, the call to ice_init_dcb()
can return a non-zero value for either an actual
error, or due to the FW lldp engine being stopped.
We are currently treating all non-zero values only as
an indication that the FW LLDP engine is stopped.
Check for an actual error in the DCB init flow.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch limits the max TCs set by the driver to the value provided by
the firmware as per the capabilities of the device. Otherwise, hard coding
to 8 TC max would fail the device configurations with more than 4 ports.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conventionally, if the #defines/other are not needed by other header
files being included, #includes are done first followed by #defines
and other stuff. Move the #defines before the #includes to follow this
convention.
Suggested by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver needs to inform the user if there is an issue
with the topology / configuration of the link.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Print the state of auto-negotiation when printing the Link
up message. Adds new text to the "NIC Link is up" line like
Autoneg: <True | False>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to recent specification versions, the field in the Queue Shutdown
AdminQ command consisting of the "driver unloading" indication is not a 4
byte field (it is byte.bit 16.0). Change it to a byte and remove the
unnecessary endian conversion.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to the specification, a PF Reset must be done as part of the
driver unload flow.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In CEE mode, the TSA information can be derived from the reported
priority value.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently if the user sets an odd value for [tx|rx]-usecs we align the
value because the hardware only understands ITR values in multiples of
2. This seems misleading because we are essentially telling the user
that the ITR value is odd, when in fact we have changed it internally.
Fix this by reporting that setting odd ITR values is not allowed.
Also, while making changes to ice_set_rc_coalesce() I noticed a bit of
code/error duplication. Make the necessary changes to remove the
duplication.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We don't free s_rule if ice_aq_sw_rules() returns a non-zero status. If
it returned a zero status, s_rule would be freed right after, so this
implies it should be freed within the scope of the function regardless.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ice_reset_subtask needs to handle EMP resets as well, as EMP resets
can be triggered by the firmware. This patch adds the logic to do
this.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add new parameter (flow_steering_mode) to control the flow steering
mode of the driver.
Two modes are supported:
1. DMFS - Device managed flow steering
2. SMFS - Software/Driver managed flow steering.
In the DMFS mode, the HW steering entities are created through the
FW. In the SMFS mode this entities are created though the driver
directly.
The driver will use the devlink steering mode only if the steering
domain supports it, for now SMFS will manages only the switchdev eswitch
steering domain.
User command examples:
- Set SMFS flow steering mode::
$ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime
- Read device flow steering mode::
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In case that flow steering mode of the driver is SMFS (Software Managed
Flow Steering), then use the DR (SW steering) API to create the steering
objects.
In addition, add a call to the set peer namespace when switchdev gets
devcom pair event. It is required to support VF LAG in SMFS.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add API to set the flow steering root namesapce mode.
Setting new mode should be called before any steering operation
is executed on the namespace.
This API is going to be used by steering users such switchdev.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support to create flow steering objects
via direct rule API (SW steering).
New layer is added - fs_dr, this layer translates the command that
fs_core sends to the FW into direct rule API. In case that direct
rule is not supported in some feature then -EOPNOTSUPP is
returned.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add new mlx5 Kconfig flag to allow selecting software steering
support and compile all the steering files only if the flag is
selected.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|