| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the comment added to exynos_dt_pmu_match[] in commit
8b283c025443 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b062 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
This reverts commit 6737b081409a4373e9d02c75aea7b916481e31b5.
Unlike on Exynos5420-family, on Exynos5410 the PMU is not an interrupt
controller so it should not handle interrupts of RTC. The DTC warning
(addressed by mentioned commit) should be fixed by not routing RTC
interrupts to PMU.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add DT info for the SPICC controller which found in
the Amlogic's Meson-AXG SoC.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable IR remote controller which found in Amlogic's Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Switch the uart_ao pclk to CLK81 since the clock driver is ready.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.
This commit is the result of:
sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*
So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.
In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:
- Base address of the registers is different for the "config-space"
- Base address of the PCIe registers, MEM, CONF and IO areas were
different
- Labels (and phandles pointing to them) of the nodes were different
("cpm" prefix in the master CP, "cps" prefix in the slave CP)
This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.
We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.
There are a few aspects that deserve additional explanations:
- PCIe needs to be handled separately because it is not part of the
config-space {...} node, since it has registers outside of the
range covered by config-space {...}.
- We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
they are used for the unit address part of some DT nodes. But since
they are also used for the "reg" property of the same nodes, we
have an ADDRESSIFY() macro that prepends 0x to those values.
We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:
- the SDHCI controller that was only described in the master CP110 is
now also described in the slave CP110. Even though the SDHCI
controller from the slave CP110 is indeed not usable (as it isn't
wired to the outside world) it is technically part of the silicon,
and therefore it is reasonable to also describe it to be part of
the slave CP110. In addition, if we wanted to get this correct for
the SDHCI controller, we should also do it for the NAND controller,
for which the situation is even more complicated: in a single CP110
configuration (Armada 7K), the usable NAND controller is in the
master CP110, while in a dual CP110 configuration (Armada 8K), the
usable NAND controller is in the slave CP110. Since that would add
a lot of additional complexity for no good reason, and since the IP
blocks are in fact really present in both CPs, we simply describe
them in both CPs at the DT level.
- the cp110-master and cp110-slave nodes are now named cpm and
cps. We could have kept cp110-master and cp110-slave, but that
would have required adding another CP110_xyz define, which didn't
seem very useful.
Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.
[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf
[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.
As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.
In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.
[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This fixes the following DTC warning:
<stdout>: Warning (simple_bus_reg): Node /ap806/config-space@f0000000/thermal@6f808C simple-bus unit address format error, expected "6f808c"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This fixes the following DTC warning:
Warning (simple_bus_reg): Node /ap806/config-space@f0000000/watchdog@600000 simple-bus unit address format error, expected "610000"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This patch adds a crypto node describing the EIP97 engine found in
Armada 37xx SoCs. The cryptographic engine is enabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:
If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.
Fixes: bb16ea1742c8 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The A711 has 1024x600 LVDS panel, with a PWM-based backlight. Add it to our
DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
MPP7 is currently muxed as "gpio", but this function doesn't exist for
MPP7, only "gpo" is available. This causes the following error:
kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp7
pinctrl core: failed to register map default (6): invalid type given
kirkwood-pinctrl f1010000.pin-controller: error claiming hogs: -22
kirkwood-pinctrl f1010000.pin-controller: could not claim hogs: -22
kirkwood-pinctrl f1010000.pin-controller: unable to register pinctrl driver
kirkwood-pinctrl: probe of f1010000.pin-controller failed with error -22
So the pinctrl driver is not probed, all device drivers (including the
UART driver) do a -EPROBE_DEFER, and therefore the system doesn't
really boot (well, it boots, but with no UART, and no devices that
require pin-muxing).
Back when the Device Tree file for this board was introduced, the
definition was already wrong. The pinctrl driver also always described
as "gpo" this function for MPP7. However, between Linux 4.10 and 4.11,
a hog pin failing to be muxed was turned from a simple warning to a
hard error that caused the entire pinctrl driver probe to bail
out. This is probably the result of commit 6118714275f0a ("pinctrl:
core: Fix pinctrl_register_and_init() with pinctrl_enable()").
This commit fixes the Device Tree to use the proper "gpo" function for
MPP7, which fixes the boot of OpenBlocks A7, which was broken since
Linux 4.11.
Fixes: f24b56cbcd9d ("ARM: kirkwood: add support for OpenBlocks A7 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The added header inclusion broke the 'allmodconfig' build in
arm-soc, presumably since the file is added in a different tree:
In file included from arch/arm64/boot/dts/sprd/sp9860g-1h10.dts:11:0:
arch/arm64/boot/dts/sprd/sc9860.dtsi:10:10: fatal error: dt-bindings/clock/sprd,sc9860-clk.h: No such file or directory
It turns out we don't actually need to include it at all, so
I'm removing the line again to fix the build.
Fixes: 22f37a242925 ("arm64: dts: add clocks for SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The A83T has an LVDS bus that can be connected to a panel or a bridge. Add
the pinctrl group for it.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has the same PWM block than the H3. Add it to our DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The display pipeline on the A83T is mainly composed of the mixers and
TCONs, plus various encoders.
Let's add the first mixer and TCON to the DTSI since the only board I have
can use only the LVDS output on the first TCON. The other parts will be
added eventually.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Some clocks on SC9860 are in the same address area with syscon devices,
those are what have a property of 'sprd,syscon' which would refer to
syscon devices, others would have a reg property indicated their address
ranges.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Some clocks on SC9860 are in the same address area with syscon
devices, the proper syscon node will be quoted under the
definitions of those clocks in DT.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Fix typo in unit address of MSCL clock controller (the reg entry is
correct) of Exynso5433.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Convert all hex addresses in node unit addresses to lower case to
fix warnings like:
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dtb: Warning (simple_bus_reg):
Node /soc/video-scaler@13C00000 simple-bus unit address format error, expected "13c00000"
Conversion was done using sed:
$ sed -e 's/@\([a-zA-Z0-9_-]*\) {/@\L\1 {/' -i arch/arm64/boot/dts/exynos/*.dts*
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The H3/H5 SoCs have a HDMI output and a TV Composite output.
Add simplefb nodes for these outputs.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
This node was the only one that didn't have the same set of pins in
active and suspend mode.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Nodes relative to the first sdhc node were interlaced with node of the
second sdhc. Move sdhc2_cd_pin with its siblings to prevent that. Also
rename the grouping node from sdhc2_cd_pin to pmx_sdc2_cd_pin, as
"pmx_sdc" is the prefix used by other nodes.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The QUP core can be used either for I2C or SPI, so the same IP is mapped
by a driver or the other. SPI bindings use a leading 0 for the start
address and a size of 0x600, I2C bindings don't have the leading 0 and
have a size 0x1000.
To make them more similar, add the leading 0 to I2C bindings and changes
the size to 0x500 for all of them, as this is the actual size of these
blocks. Also align the second entry of the clocks array.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
These nodes reserve and configure some pins as GPIOs. They are not
generic pinctrls, they actually belong to board files but they are not
used by any other node, so just drop them altogether.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Drop assignments to bias-disable as the documentation [1] states that
this property doesn't take a value. Other occurrences of this property
respect that.
[1] Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Indentation did not respect kernel standards, so fix that for the usual
indent with tabs, align with spaces. While at it, remove some empty
lines before and after the closing parenthesis of this block.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.
Fixes: 1fb47e0a9ba4 ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes")
Cc: stable@vger.kernel.org
Reported-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add a missing #phy-cells to the dsi-phy, to silence dtc warning.
Cc: Archit Taneja <architt@codeaurora.org>
Fixes: 305410ffd1b2 ("arm64: dts: msm8916: Add display support")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Use tcb0 for timers as selected in sama5_defconfig.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Use tcb0 for timers as selected in sama5_defconfig.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Use tcb0 for timers as selected in sama5_defconfig.
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
As TCB2 doesn't have any output pins, use it for timers
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
As TCB2 doesn't have any output pins, use it for timers
Cc: Marek Vasut <marex@denx.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
As TCB2 doesn't have any output pins, use for timers.
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
Arnd Bergmann
Krzysztof Kozlowski
Yixun Lan
Sunny Luo
Yan Markman
Thomas Petazzoni
Antoine Tenart
Gregory CLEMENT
Maxime Ripard
Linus Walleij
Chunyan Zhang
Icenowy Zheng
Damien Riegel
Bjorn Andersson
Nicolas Ferre
Alexandre Belloni