aboutsummaryrefslogtreecommitdiffstats
path: root/tools/perf/scripts/python/export-to-postgresql.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2021-10-21sfc: Export fibre-specific supported link modesErik Ekman1-11/+26
The 1/10GbaseT modes were set up for cards with SFP+ cages in 3497ed8c852a5 ("sfc: report supported link speeds on SFP connections"). 10GbaseT was likely used since no 10G fibre mode existed. The missing fibre modes for 1/10G were added to ethtool.h in 5711a9822144 ("net: ethtool: add support for 1000BaseX and missing 10G link modes") shortly thereafter. The user guide available at https://support-nic.xilinx.com/wp/drivers lists support for the following cable and transceiver types in section 2.9: - QSFP28 100G Direct Attach Cables - QSFP28 100G SR Optical Transceivers (with SR4 modules listed) - SFP28 25G Direct Attach Cables - SFP28 25G SR Optical Transceivers - QSFP+ 40G Direct Attach Cables - QSFP+ 40G Active Optical Cables - QSFP+ 40G SR4 Optical Transceivers - QSFP+ to SFP+ Breakout Direct Attach Cables - QSFP+ to SFP+ Breakout Active Optical Cables - SFP+ 10G Direct Attach Cables - SFP+ 10G SR Optical Transceivers - SFP+ 10G LR Optical Transceivers - SFP 1000BASE‐T Transceivers - 1G Optical Transceivers (From user guide issue 28. Issue 16 which also includes older cards like SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.) Regarding SFP+ 10GBASE‐T transceivers the latest guide says: "Solarflare adapters do not support 10GBASE‐T transceiver modules." Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR). Before: $ ethtool ext Settings for ext: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 10000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Link partner advertised link modes: Not reported Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: off Port: FIBRE PHYAD: 255 Transceiver: internal Current message level: 0x000020f7 (8439) drv probe link ifdown ifup rx_err tx_err hw Link detected: yes After: $ ethtool ext Settings for ext: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 1000baseX/Full 10000baseCR/Full 10000baseSR/Full 10000baseLR/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Link partner advertised link modes: Not reported Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: off Port: FIBRE PHYAD: 255 Transceiver: internal Supports Wake-on: g Wake-on: d Current message level: 0x000020f7 (8439) drv probe link ifdown ifup rx_err tx_err hw Link detected: yes Signed-off-by: Erik Ekman <erik@kryo.se> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net/mlx5e: IPsec: Fix work queue entry ethernet segment checksum flagsEmeel Hakim1-9/+11
Current Work Queue Entry (WQE) checksum (csum) flags in the ethernet segment (eseg) in case of IPsec crypto offload datapath are not aligned with PRM/HW expectations. Currently the driver always sets the l3_inner_csum flag in case of IPsec because of the wrong usage of skb->encapsulation as indicator for inner IPsec header since skb->encapsulation is always ON for IPsec packets since IPsec itself is an encapsulation protocol. The above forced a failing attempts of calculating csum of non-existing segments (like in the IP|ESP|TCP packet case which does not have an l3_inner) which led to lots of packet drops hence the low throughput. Fix by using xo->inner_ipproto as indicator for inner IPsec header instead of skb->encapsulation in addition to setting the csum flags as following: * Tunnel Mode: * Pkt: MAC IP ESP IP L4 * CSUM: l3_cs | l3_inner_cs | l4_inner_cs * * Transport Mode: * Pkt: MAC IP ESP L4 * CSUM: l3_cs [ | l4_cs (checksum partial case)] * * Tunnel(VXLAN TCP/UDP) over Transport Mode * Pkt: MAC IP ESP UDP VXLAN IP L4 * CSUM: l3_cs | l3_inner_cs | l4_inner_cs Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload") Signed-off-by: Emeel Hakim <ehakim@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20net/mlx5e: IPsec: Fix a misuse of the software parser's fieldsEmeel Hakim1-24/+27
IPsec crypto offload current Software Parser (SWP) fields settings in the ethernet segment (eseg) are not aligned with PRM/HW expectations. Among others in case of IP|ESP|TCP packet, current driver sets the offsets for inner_l3 and inner_l4 although there is no inner l3/l4 headers relative to ESP header in such packets. SWP provides the offsets for HW ,so it can be used to find csum fields to offload the checksum, however these are not necessarily used by HW and are used as fallback in case HW fails to parse the packet, e.g when performing IPSec Transport Aware (IP | ESP | TCP) there is no need to add SW parse on inner packet. So in some cases packets csum was calculated correctly , whereas in other cases it failed. The later faced csum errors (caused by wrong packet length calculations) which led to lots of packet drops hence the low throughput. Fix by setting the SWP fields as expected in a IP|ESP|TCP packet. the following describe the expected SWP offsets: * Tunnel Mode: * SWP: OutL3 InL3 InL4 * Pkt: MAC IP ESP IP L4 * * Transport Mode: * SWP: OutL3 OutL4 * Pkt: MAC IP ESP L4 * * Tunnel(VXLAN TCP/UDP) over Transport Mode * SWP: OutL3 InL3 InL4 * Pkt: MAC IP ESP UDP VXLAN IP L4 Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload") Signed-off-by: Emeel Hakim <ehakim@nvidia.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20net/mlx5e: Fix vlan data lost during suspend flowMoshe Shemesh3-12/+26
During suspend flow the driver calls mlx5e_destroy_vlan_table() which does not only delete the vlans steering flow rules, but also frees the data on currently active vlans, thus it is not restored during resume flow. This fix keeps the vlan data on suspend flow and frees it only on driver remove flow. Fixes: 6783f0a21a3c ("net/mlx5e: Dynamic alloc vlan table for netdev when needed") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20net/mlx5: E-switch, Return correct error code on group creation failureDmytro Linkin1-4/+3
Dan Carpenter report: The patch f47e04eb96e0: "net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups" from May 31, 2021, leads to the following Smatch static checker warning: drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group() warn: passing zero to 'ERR_PTR' If min rate normalization failed then error code may be overwritten to 0 if scheduling element destruction succeed. Ignore this value and always return initial one. Fixes: f47e04eb96e0 ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20net/mlx5: Lag, change multipath and bonding to be mutually exclusiveMaor Dickman6-6/+18
Both multipath and bonding events are changing the HW LAG state independently. Handling one of the features events while the other is already enabled can cause unwanted behavior, for example handling bonding event while multipath enabled will disable the lag and cause multipath to stop working. Fix it by ignoring bonding event while in multipath and ignoring FIB events while in bonding mode. Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20ice: Add missing E810 device idsTony Nguyen3-0/+8
As part of support for E810 XXV devices, some device ids were inadvertently left out. Add those missing ids. Fixes: 195fb97766da ("ice: add additional E810 device id") Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
2021-10-20igc: Update I226_K device IDSasha Neftin1-1/+1
The device ID for I226_K was incorrectly assigned, update the device ID to the correct one. Fixes: bfa5e98c9de4 ("igc: Add new device ID") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20e1000e: Fix packet loss on Tiger Lake and laterSasha Neftin2-1/+13
Update the HW MAC initialization flow. Do not gate DMA clock from the modPHY block. Keeping this clock will prevent dropped packets sent in burst mode on the Kumeran interface. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377 Fixes: fb776f5d57ee ("e1000e: Add support for Tiger Lake") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Mark Pearson <markpearson@lenovo.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20e1000e: Separate TGP board type from SPTSasha Neftin3-23/+46
We have the same LAN controller on different PCHs. Separate TGP board type from SPT which will allow for specific fixes to be applied for TGP platforms. Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Mark Pearson <markpearson@lenovo.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20ptp: Fix possible memory leak in ptp_clock_register()Yang Yingliang1-4/+11
I got memory leak as follows when doing fault injection test: unreferenced object 0xffff88800906c618 (size 8): comm "i2c-idt82p33931", pid 4421, jiffies 4294948083 (age 13.188s) hex dump (first 8 bytes): 70 74 70 30 00 00 00 00 ptp0.... backtrace: [<00000000312ed458>] __kmalloc_track_caller+0x19f/0x3a0 [<0000000079f6e2ff>] kvasprintf+0xb5/0x150 [<0000000026aae54f>] kvasprintf_const+0x60/0x190 [<00000000f323a5f7>] kobject_set_name_vargs+0x56/0x150 [<000000004e35abdd>] dev_set_name+0xc0/0x100 [<00000000f20cfe25>] ptp_clock_register+0x9f4/0xd30 [ptp] [<000000008bb9f0de>] idt82p33_probe.cold+0x8b6/0x1561 [ptp_idt82p33] When posix_clock_register() returns an error, the name allocated in dev_set_name() will be leaked, the put_device() should be used to give up the device reference, then the name will be freed in kobject_cleanup() and other memory will be freed in ptp_clock_release(). Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: a33121e5487b ("ptp: fix the race between the release of ptp_clock and cdev") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: stmmac: Fix E2E delay mechanismKurt Kanzenbach1-1/+1
When utilizing End to End delay mechanism, the following error messages show up: |root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m |ptp4l[950.573]: selected /dev/ptp3 as PTP clock |ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1 |ptp4l[956.879]: selected best master clock 001395.fffe.4897b4 |ptp4l[956.879]: port 1: assuming the grand master role |ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER |ptp4l[962.017]: port 1: received DELAY_REQ without timestamp |ptp4l[962.273]: port 1: received DELAY_REQ without timestamp |ptp4l[963.090]: port 1: received DELAY_REQ without timestamp Commit f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") already addresses this problem for the dwmac v5.10. However, same holds true for all dwmacs above version v4.10. Correct the check accordingly. Afterwards everything works as expected. Tested on Intel Atom(R) x6414RE Processor. Fixes: 14f347334bf2 ("net: stmmac: Correctly take timestamp for PTPv2") Fixes: f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20nfc: st95hf: Make spi remove() callback return zeroUwe Kleine-König1-4/+2
If something goes wrong in the remove callback, returning an error code just results in an error message. The device still disappears. So don't skip disabling the regulator in st95hf_remove() if resetting the controller via spi fails. Also don't return an error code which just results in two error messages. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: disable sriov before unload hclge layerPeng Li3-0/+23
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko. hns3.ko includes network stack and pci_driver, hclge.ko includes HW device action, algo_ops and timer task, hnae3.ko includes some register function. When SRIOV is enable and hclge.ko is removed, HW device is unloaded but VF still exists, PF will not reply VF mbx messages, and cause errors. This patch fix it by disable SRIOV before remove hclge.ko. Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: fix vf reset workqueue cannot exitYufeng Mo1-3/+3
The task of VF reset is performed through the workqueue. It checks the value of hdev->reset_pending to determine whether to exit the loop. However, the value of hdev->reset_pending may also be assigned by the interrupt function hclgevf_misc_irq_handle(), which may cause the loop fail to exit and keep occupying the workqueue. This loop is not necessary, so remove it and the workqueue will be rescheduled if the reset needs to be retried or a new reset occurs. Fixes: 1cc9bc6e5867 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: schedule the polling again when allocation failsYunsheng Lin1-10/+12
Currently when there is a rx page allocation failure, it is possible that polling may be stopped if there is no more packet to be reveiced, which may cause queue stall problem under memory pressure. This patch makes sure polling is scheduled again when there is any rx page allocation failure, and polling will try to allocate receive buffers until it succeeds. Now the allocation retry is added, it is unnecessary to do the rx page allocation at the end of rx cleaning, so remove it. And reset the unused_count to zero after calling hns3_nic_alloc_rx_buffers() to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under memory pressure. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: fix for miscalculation of rx unused descYunsheng Lin2-0/+9
rx unused desc is the desc that need attatching new buffer before refilling to hw to receive new packet, the number of desc need attatching new buffer is calculated using next_to_use and next_to_clean. when next_to_use == next_to_clean, currently hns3 driver assumes that all the desc has the buffer attatched, but 'next_to_use == next_to_clean' also means all the desc need attatching new buffer if hw has comsumed all the desc and the driver has not attatched any buffer to the desc yet. This patch adds 'refill' in desc_cb to indicate whether a new buffer has been refilled to a desc. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: fix the max tx size according to user manualYunsheng Lin2-9/+4
Currently the max tx size supported by the hw is calculated by using the max BD num supported by the hw. According to the hw user manual, the max tx size is fixed value for both non-TSO and TSO skb. This patch updates the max tx size according to the manual. Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: add limit ets dwrr bandwidth cannot be 0Guangbin Huang1-0/+9
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP mode. In this case, this tc may occupy all the tx bandwidth if it has huge traffic, so it violates the purpose of the user setting. To fix this problem, limit the ets dwrr bandwidth must greater than 0. Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: reset DWRR of unused tc to zeroGuangbin Huang1-0/+2
Currently, DWRR of tc will be initialized to a fixed value when this tc is enabled, but it is not been reset to 0 when this tc is disabled. It cause a problem that the DWRR of unused tc is not 0 after using tc tool to add and delete multi-tc parameters. For examples, after enabling 4 TCs and restoring to 1 TC by follow tc commands: $ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \ 8@0 8@8 8@16 8@24 hw 1 mode channel $ tc qdisc del dev eth0 root Now there is just one TC is enabled for eth0, but the tc info querying by debugfs is shown as follow: $ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info enabled tc number: 1 weight_offset: 14 TC MODE WEIGHT 0 dwrr 100 1 dwrr 100 2 dwrr 100 3 dwrr 100 4 dwrr 0 5 dwrr 0 6 dwrr 0 7 dwrr 0 This patch fixes it by resetting DWRR of tc to 0 when tc is disabled. Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: Add configuration of TM QCN error eventJiaran Zhang2-1/+6
Add configuration of interrupt type and fifo interrupt enable of TM QCN error event if enabled, otherwise this event will not be reported when there is error. Fixes: d914971df022 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20vrf: Revert "Reset skb conntrack connection..."Eugene Crosser1-4/+0
This reverts commit 09e856d54bda5f288ef8437a90ab2b9b3eab83d1. When an interface is enslaved in a VRF, prerouting conntrack hook is called twice: once in the context of the original input interface, and once in the context of the VRF interface. If no special precausions are taken, this leads to creation of two conntrack entries instead of one, and breaks SNAT. Commit above was intended to avoid creation of extra conntrack entries when input interface is enslaved in a VRF. It did so by resetting conntrack related data associated with the skb when it enters VRF context. However it breaks netfilter operation. Imagine a use case when conntrack zone must be assigned based on the original input interface, rather than VRF interface (that would make original interfaces indistinguishable). One could create netfilter rules similar to these: chain rawprerouting { type filter hook prerouting priority raw; iif realiface1 ct zone set 1 return iif realiface2 ct zone set 2 return } This works before the mentioned commit, but not after: zone assignment is "forgotten", and any subsequent NAT or filtering that is dependent on the conntrack zone does not work. Here is a reproducer script that demonstrates the difference in behaviour. ========== #!/bin/sh # This script demonstrates unexpected change of nftables behaviour # caused by commit 09e856d54bda5f28 ""vrf: Reset skb conntrack # connection on VRF rcv" # https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1 # # Before the commit, it was possible to assign conntrack zone to a # packet (or mark it for `notracking`) in the prerouting chanin, raw # priority, based on the `iif` (interface from which the packet # arrived). # After the change, # if the interface is enslaved in a VRF, such # assignment is lost. Instead, assignment based on the `iif` matching # the VRF master interface is honored. Thus it is impossible to # distinguish packets based on the original interface. # # This script demonstrates this change of behaviour: conntrack zone 1 # or 2 is assigned depending on the match with the original interface # or the vrf master interface. It can be observed that conntrack entry # appears in different zone in the kernel versions before and after # the commit. IPIN=172.30.30.1 IPOUT=172.30.30.2 PFXL=30 ip li sh vein >/dev/null 2>&1 && ip li del vein ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf nft list table testct >/dev/null 2>&1 && nft delete table testct ip li add vein type veth peer veout ip li add tvrf type vrf table 9876 ip li set veout master tvrf ip li set vein up ip li set veout up ip li set tvrf up /sbin/sysctl -w net.ipv4.conf.veout.accept_local=1 /sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0 ip addr add $IPIN/$PFXL dev vein ip addr add $IPOUT/$PFXL dev veout nft -f - <<__END__ table testct { chain rawpre { type filter hook prerouting priority raw; iif { veout, tvrf } meta nftrace set 1 iif veout ct zone set 1 return iif tvrf ct zone set 2 return notrack } chain rawout { type filter hook output priority raw; notrack } } __END__ uname -rv conntrack -F ping -W 1 -c 1 -I vein $IPOUT conntrack -L Signed-off-by: Eugene Crosser <crosser@average.org> Acked-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-19net: dsa: Fix an error handling path in 'dsa_switch_parse_ports_of()'Christophe JAILLET1-2/+7
If we return before the end of the 'for_each_child_of_node()' iterator, the reference taken on 'port' must be released. Add the missing 'of_node_put()' calls. Fixes: 83c0afaec7b7 ("net: dsa: Add new binding implementation") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/15d5310d1d55ad51c1af80775865306d92432e03.1634587046.git.christophe.jaillet@wanadoo.fr Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-19cavium: Fix return values of the probe functionZheyu Ma1-2/+2
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-19mISDN: Fix return values of the probe functionZheyu Ma1-4/+4
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-19can: isotp: isotp_sendmsg(): fix return error on FC timeout on TX pathMarc Kleine-Budde1-0/+3
When the a large chunk of data send and the receiver does not send a Flow Control frame back in time, the sendmsg() does not return a error code, but the number of bytes sent corresponding to the size of the packet. If a timeout occurs the isotp_tx_timer_handler() is fired, sets sk->sk_err and calls the sk->sk_error_report() function. It was wrongly expected that the error would be propagated to user space in every case. For isotp_sendmsg() blocking on wait_event_interruptible() this is not the case. This patch fixes the problem by checking if sk->sk_err is set and returning the error to user space. Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://github.com/hartkopp/can-isotp/issues/42 Link: https://github.com/hartkopp/can-isotp/pull/43 Link: https://lore.kernel.org/all/20210507091839.1366379-1-mkl@pengutronix.de Cc: stable@vger.kernel.org Reported-by: Sottas Guillaume (LMB) <Guillaume.Sottas@liebherr.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-18nfp: bpf: silence bitwise vs. logical OR warningNathan Chancellor1-2/+2
A new warning in clang points out two places in this driver where boolean expressions are being used with a bitwise OR instead of a logical one: drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: note: cast one or both operands to int to silence this warning drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: note: cast one or both operands to int to silence this warning 2 errors generated. The motivation for the warning is that logical operations short circuit while bitwise operations do not. In this case, it does not seem like short circuiting is harmful so implement the suggested fix of changing to a logical operation to fix the warning. Link: https://github.com/ClangBuiltLinux/linux/issues/1479 Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211018193101.2340261-1-nathan@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-18selftests/tls: add SM4 algorithm dependency for tls selftestsTianjia Zhang1-0/+1
Kernel TLS test has added SM4 GCM/CCM algorithm support, but SM4 algorithm is not compiled by default, this patch add SM4 config dependency. Reported-by: Hangbin Liu <liuhangbin@gmail.com> Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18mctp: Be explicit about struct sockaddr_mctp paddingJeremy Kerr1-0/+2
We currently have some implicit padding in struct sockaddr_mctp. This patch makes this padding explicit, and ensures we have consistent layout on platforms with <32bit alignmnent. Fixes: 60fc63981693 ("mctp: Add sockaddr_mctp to uapi") Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18mctp: unify sockaddr_mctp typesJeremy Kerr3-8/+9
Use the more precise __kernel_sa_family_t for smctp_family, to match struct sockaddr. Also, use an unsigned int for the network member; negative networks don't make much sense. We're already using unsigned for mctp_dev and mctp_skb_cb, but need to change mctp_sock to suit. Fixes: 60fc63981693 ("mctp: Add sockaddr_mctp to uapi") Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Acked-by: Eugene Syromiatnikov <esyr@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18cavium: Return negative value when pci_alloc_irq_vectors() failsZheyu Ma1-1/+1
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18net: mscc: ocelot: Add of_node_put() before gotoWan Jiabing1-0/+1
Fix following coccicheck warning: ./drivers/net/ethernet/mscc/ocelot_vsc7514.c:946:1-33: WARNING: Function for_each_available_child_of_node should have of_node_put() before goto. Early exits from for_each_available_child_of_node should decrement the node reference counter. Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18net: sparx5: Add of_node_put() before gotoWan Jiabing1-0/+1
Fix following coccicheck warning: ./drivers/net/ethernet/microchip/sparx5/s4parx5_main.c:723:1-33: WARNING: Function for_each_available_child_of_node should have of_node_put() before goto Early exits from for_each_available_child_of_node should decrement the node reference counter. Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18net/sched: act_ct: Fix byte count on fragmented packetsPaul Blakey1-1/+1
First fragmented packets (frag offset = 0) byte len is zeroed when stolen by ip_defrag(). And since act_ct update the stats only afterwards (at end of execute), bytes aren't correctly accounted for such packets. To fix this, move stats update to start of action execute. Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct") Signed-off-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18net: dsa: mt7530: correct ds->num_portsDENG Qingfang1-7/+1
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary dsa_port's and call mt7530_port_disable for non-existent ports. Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in port_enable/disable is no longer required. Cc: stable@vger.kernel.org Signed-off-by: DENG Qingfang <dqfext@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18net: dsa: lantiq_gswip: fix register definitionAleksander Jan Bajkowski1-1/+1
I compared the register definitions with the D-Link DWR-966 GPL sources and found that the PUAFD field definition was incorrect. This definition is unused and causes no issues. Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18hamradio: baycom_epp: fix build for UMLRandy Dunlap1-3/+3
On i386, the baycom_epp driver wants to inspect X86 CPU features (TSC) and then act on that data, but that info is not available when running on UML, so prevent that test and do the default action. Prevents this build error on UML + i386: ../drivers/net/hamradio/baycom_epp.c: In function ‘epp_bh’: ../drivers/net/hamradio/baycom_epp.c:630:6: error: implicit declaration of function ‘boot_cpu_has’; did you mean ‘get_cpu_mask’? [-Werror=implicit-function-declaration] if (boot_cpu_has(X86_FEATURE_TSC)) \ ^ ../drivers/net/hamradio/baycom_epp.c:658:2: note: in expansion of macro ‘GETTICK’ GETTICK(time1); Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: linux-um@lists.infradead.org Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Thomas Sailer <t.sailer@alumni.ethz.ch> Cc: linux-hams@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-18netfilter: ebtables: allocate chainstack on CPU local nodesDavidlohr Bueso1-1/+3
Keep the per-CPU memory allocated for chainstacks local. Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2021-10-17can: peak_usb: pcan_usb_fd_decode_status(): remove unnecessary test on the nullity of a pointerStephane Grosjean1-2/+1
Since alloc_can_err_skb() puts NULL in cf in the case when skb cannot be allocated and can_change_state() handles the case when cf is NULL, the test on the nullity of skb is now unnecessary. Link: https://lore.kernel.org/all/20210929142111.55757-2-s.grosjean@peak-system.com Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: peak_usb: pcan_usb_fd_decode_status(): fix back to ERROR_ACTIVE state notificationStephane Grosjean1-3/+2
This corrects the lack of notification of a return to ERROR_ACTIVE state for USB - CANFD devices from PEAK-System. Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Link: https://lore.kernel.org/all/20210929142111.55757-1-s.grosjean@peak-system.com Cc: stable@vger.kernel.org Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: peak_pci: peak_pci_remove(): fix UAFZheyu Ma1-5/+4
When remove the module peek_pci, referencing 'chan' again after releasing 'dev' will cause UAF. Fix this by releasing 'dev' later. The following log reveals it: [ 35.961814 ] BUG: KASAN: use-after-free in peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.963414 ] Read of size 8 at addr ffff888136998ee8 by task modprobe/5537 [ 35.965513 ] Call Trace: [ 35.965718 ] dump_stack_lvl+0xa8/0xd1 [ 35.966028 ] print_address_description+0x87/0x3b0 [ 35.966420 ] kasan_report+0x172/0x1c0 [ 35.966725 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967137 ] ? trace_irq_enable_rcuidle+0x10/0x170 [ 35.967529 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967945 ] __asan_report_load8_noabort+0x14/0x20 [ 35.968346 ] peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.968752 ] pci_device_remove+0xa9/0x250 Fixes: e6d9c80b7ca1 ("can: peak_pci: add support of some new PEAK-System PCI cards") Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: m_can: fix iomap_read_fifo() and iomap_write_fifo()Aswath Govindraju1-2/+12
The read and writes from the fifo are from a buffer, with various fields and data at predefined offsets. So, they should not be done to the same address(or port) in case of val_count greater than 1. Therefore, fix this by using iowrite32()/ioread32() instead of ioread32_rep()/iowrite32_rep(). Also, the write into FIFO must be performed with an offset from the message ram base address. Therefore, fix the base address to mram_base. Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors") Link: https://lore.kernel.org/all/20210920123344.2320-1-a-govindraju@ti.com Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: rcar_can: fix suspend/resumeYoshihiro Shimoda1-8/+12
If the driver was not opened, rcar_can_suspend() should not call clk_disable() because the clock was not enabled. Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver") Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com Cc: stable@vger.kernel.org Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Tested-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: isotp: isotp_sendmsg(): fix TX buffer concurrent access in isotp_sendmsg()Ziyang Xuan1-15/+31
When isotp_sendmsg() concurrent, tx.state of all TX processes can be ISOTP_IDLE. The conditions so->tx.state != ISOTP_IDLE and wq_has_sleeper(&so->wait) can not protect TX buffer from being accessed by multiple TX processes. We can use cmpxchg() to try to modify tx.state to ISOTP_SENDING firstly. If the modification of the previous process succeed, the later process must wait tx.state to ISOTP_IDLE firstly. Thus, we can ensure TX buffer is accessed by only one process at the same time. And we should also restore the original tx.state at the subsequent error processes. Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/c2517874fbdf4188585cf9ddf67a8fa74d5dbde5.1633764159.git.william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: isotp: isotp_sendmsg(): add result check for wait_event_interruptible()Ziyang Xuan1-1/+3
Using wait_event_interruptible() to wait for complete transmission, but do not check the result of wait_event_interruptible() which can be interrupted. It will result in TX buffer has multiple accessors and the later process interferes with the previous process. Following is one of the problems reported by syzbot. ============================================================= WARNING: CPU: 0 PID: 0 at net/can/isotp.c:840 isotp_tx_timer_handler+0x2e0/0x4c0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.0-rc7+ #68 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014 RIP: 0010:isotp_tx_timer_handler+0x2e0/0x4c0 Call Trace: <IRQ> ? isotp_setsockopt+0x390/0x390 __hrtimer_run_queues+0xb8/0x610 hrtimer_run_softirq+0x91/0xd0 ? rcu_read_lock_sched_held+0x4d/0x80 __do_softirq+0xe8/0x553 irq_exit_rcu+0xf8/0x100 sysvec_apic_timer_interrupt+0x9e/0xc0 </IRQ> asm_sysvec_apic_timer_interrupt+0x12/0x20 Add result check for wait_event_interruptible() in isotp_sendmsg() to avoid multiple accessers for tx buffer. Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/10ca695732c9dd267c76a3c30f37aefe1ff7e32f.1633764159.git.william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Reported-by: syzbot+78bab6958a614b0c80b9@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: j1939: j1939_xtp_rx_rts_session_new(): abort TP less than 9 bytesZhang Changzhong2-0/+3
The receiver should abort TP if 'total message size' in TP.CM_RTS and TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the j1939 stack only checks the upper bound and the receiver will accept the following broadcast message: vcan1 18ECFF00 [8] 20 08 00 02 FF 00 23 01 vcan1 18EBFF00 [8] 01 00 00 00 00 00 00 00 vcan1 18EBFF00 [8] 02 00 FF FF FF FF FF FF This patch adds check for the lower bound and abort illegal TP. [1] SAE-J1939-82 A.3.4 Row 2 and A.3.6 Row 6. Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/1634203601-3460-1-git-send-email-zhangchangzhong@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: j1939: j1939_xtp_rx_dat_one(): cancel session if receive TP.DT with error lengthZhang Changzhong1-2/+5
According to SAE-J1939-21, the data length of TP.DT must be 8 bytes, so cancel session when receive unexpected TP.DT message. Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/1632972800-45091-1-git-send-email-zhangchangzhong@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: j1939: j1939_netdev_start(): fix UAF for rx_kref of j1939_privZiyang Xuan1-2/+5
It will trigger UAF for rx_kref of j1939_priv as following. cpu0 cpu1 j1939_sk_bind(socket0, ndev0, ...) j1939_netdev_start j1939_sk_bind(socket1, ndev0, ...) j1939_netdev_start j1939_priv_set j1939_priv_get_by_ndev_locked j1939_jsk_add ..... j1939_netdev_stop kref_put_lock(&priv->rx_kref, ...) kref_get(&priv->rx_kref, ...) REFCOUNT_WARN("addition on 0;...") ==================================================== refcount_t: addition on 0; use-after-free. WARNING: CPU: 1 PID: 20874 at lib/refcount.c:25 refcount_warn_saturate+0x169/0x1e0 RIP: 0010:refcount_warn_saturate+0x169/0x1e0 Call Trace: j1939_netdev_start+0x68b/0x920 j1939_sk_bind+0x426/0xeb0 ? security_socket_bind+0x83/0xb0 The rx_kref's kref_get() and kref_put() should use j1939_netdev_lock to protect. Fixes: 9d71dd0c70099 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/20210926104757.2021540-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Reported-by: syzbot+85d9878b19c94f9019ad@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: j1939: j1939_tp_rxtimer(): fix errant alert in j1939_tp_rxtimerZiyang Xuan1-3/+2
When the session state is J1939_SESSION_DONE, j1939_tp_rxtimer() will give an alert "rx timeout, send abort", but do nothing actually. Move the alert into session active judgment condition, it is more reasonable. One of the scenarios is that j1939_tp_rxtimer() execute followed by j1939_xtp_rx_abort_one(). After j1939_xtp_rx_abort_one(), the session state is J1939_SESSION_DONE, then j1939_tp_rxtimer() give an alert. Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/20210906094219.95924-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-16net: bridge: mcast: use multicast_membership_interval for IGMPv3Nikolay Aleksandrov1-3/+1
When I added IGMPv3 support I decided to follow the RFC for computing the GMI dynamically: " 8.4. Group Membership Interval The Group Membership Interval is the amount of time that must pass before a multicast router decides there are no more members of a group or a particular source on a network. This value MUST be ((the Robustness Variable) times (the Query Interval)) plus (one Query Response Interval)." But that actually is inconsistent with how the bridge used to compute it for IGMPv2, where it was user-configurable that has a correct default value but it is up to user-space to maintain it. This would make it consistent with the other timer values which are also maintained correct by the user instead of being dynamically computed. It also changes back to the previous user-expected GMI behaviour for IGMPv3 queries which were supported before IGMPv3 was added. Note that to properly compute it dynamically we would need to add support for "Robustness Variable" which is currently missing. Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: 0436862e417e ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.