| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The current ITS driver is assuming every ITS hardware implementation
supports minimum of 16bit INTID. But this is not true, as per GICv3
specification, INTID field is IMPLEMENTATION DEFINED in the range of
14-24 bits. We might see an unpredictable system behavior on systems
where hardware support less than 16bits and software tries to use
64K LPI interrupts.
On Qualcomm Datacenter Technologies QDF2400 platform, boot log shows
confusing information about number of LPI chunks as shown below. The
QDF2400 ITS hardware supports 24bit INTID.
This patch allocates the memory resources for PEND/PROP tables based
on discoverable value which is specified in GITS_TYPER.IDbits. Also
it fixes the log message that reflects the correct number of LPI
chunks were allocated.
ITS@0xff7efe0000: allocated 524288 Devices @3c0400000 (indirect, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Interrupt Collections @3c0130000 (flat, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Virtual CPUs @3c0140000 (flat, esz 8, psz 64K, shr 1)
ITS: Allocated 524032 chunks for LPIs
PCI/MSI: ITS@0xff7efe0000 domain created
Platform MSI: ITS@0xff7efe0000 domain created
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add code to parse SRAT ITS Affinity sub table as defined in ACPI 6.2.
Later in per device probe, ITS devices are mapped to numa node using
ITS Id to proximity domain mapping.
[maz: fix dependency on ACPICA, fixed structure name, minor cleanups]
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The Marvell ICU unit is found in the CP110 block of the Marvell Armada
7K and 8K SoCs. It collects the wired interrupts of the devices located
in the CP110 and turns them into SPI interrupts in the GIC located in
the AP806 side of the SoC, by using a memory transaction.
Until now, the ICU was configured in a static fashion by the firmware,
and Linux was relying on this static configuration. By having Linux
configure the ICU, we are more flexible, and we can allocate dynamically
the GIC SPI interrupts only for devices that are actually in use.
The driver was initially written by Hanna Hawa <hannah@marvell.com>.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
Shanker Donthineni
Ganapatrao Kulkarni
Arvind Yadav
Thomas Petazzoni