| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
xrx200_hw_receive() assumes build_skb() always works and goes straight
to skb_reserve(). However, build_skb() can fail under memory pressure.
Add a check in case build_skb() failed to allocate and return NULL.
Fixes: e015593573b3 ("net: lantiq_xrx200: convert to build_skb")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a follow-up to the discussion in [0]. It seems to me that
at least the IP version used on Amlogic SoC's sometimes has a problem
if register MAC_CTRL_REG is written whilst the chip is still processing
a previous write. But that's just a guess.
Adding a delay between two writes to this register helps, but we can
also simply omit the offending second write. This patch uses the second
approach and is based on a suggestion from Qi Duan.
Benefit of this approach is that we can save few register writes, also
on not affected chip versions.
[0] https://www.spinics.net/lists/netdev/msg831526.html
Fixes: bfab27a146ed ("stmmac: add the experimental PCI support")
Suggested-by: Qi Duan <qi.duan@amlogic.com>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/e99857ce-bd90-5093-ca8c-8cd480b5a0a2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Assign a random mac address to the VF interface station
address if it boots with a zero mac address in order to match
similar behavior seen in other VF drivers. Handle the errors
where the older firmware does not allow the VF to set its own
station address.
Newer firmware will allow the VF to set the station mac address
if it hasn't already been set administratively through the PF.
Setting it will also be allowed if the VF has trust.
Fixes: fbb39807e9ae ("ionic: support sr-iov operations")
Signed-off-by: R Mohamed Shah <mohamed@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In looping on FW update tests we occasionally see the
FW_ACTIVATE_STATUS command fail while it is in its EAGAIN loop
waiting for the FW activate step to finsh inside the FW. The
firmware is complaining that the done bit is set when a new
dev_cmd is going to be processed.
Doing a clean on the cmd registers and doorbell before exiting
the wait-for-done and cleaning the done bit before the sleep
prevents this from occurring.
Fixes: fbfb8031533c ("ionic: Add hardware init and device commands")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a case found in heavy testing where a link flap happens just
before a firmware Recovery event and the driver gets stuck in the
BROKEN state. This comes from the driver getting interrupted by a FW
generation change when coming back up from the link flap, and the call
to ionic_start_queues() in ionic_link_status_check() fails. This can be
addressed by having the fw_up code clear the BROKEN bit if seen, rather
than waiting for a user to manually force the interface down and then
back up.
Fixes: 9e8eaf8427b6 ("ionic: stop watchdog when in broken state")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix three bugs in the rxrpc's sendmsg implementation:
(1) rxrpc_new_client_call() should release the socket lock when returning
an error from rxrpc_get_call_slot().
(2) rxrpc_wait_for_tx_window_intr() will return without the call mutex
held in the event that we're interrupted by a signal whilst waiting
for tx space on the socket or relocking the call mutex afterwards.
Fix this by: (a) moving the unlock/lock of the call mutex up to
rxrpc_send_data() such that the lock is not held around all of
rxrpc_wait_for_tx_window*() and (b) indicating to higher callers
whether we're return with the lock dropped. Note that this means
recvmsg() will not block on this call whilst we're waiting.
(3) After dropping and regaining the call mutex, rxrpc_send_data() needs
to go and recheck the state of the tx_pending buffer and the
tx_total_len check in case we raced with another sendmsg() on the same
call.
Thinking on this some more, it might make sense to have different locks for
sendmsg() and recvmsg(). There's probably no need to make recvmsg() wait
for sendmsg(). It does mean that recvmsg() can return MSG_EOR indicating
that a call is dead before a sendmsg() to that call returns - but that can
currently happen anyway.
Without fix (2), something like the following can be induced:
WARNING: bad unlock balance detected!
5.16.0-rc6-syzkaller #0 Not tainted
-------------------------------------
syz-executor011/3597 is trying to release lock (&call->user_mutex) at:
[<ffffffff885163a3>] rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
but there are no more locks to release!
other info that might help us debug this:
no locks held by syz-executor011/3597.
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_unlock_imbalance_bug include/trace/events/lock.h:58 [inline]
__lock_release kernel/locking/lockdep.c:5306 [inline]
lock_release.cold+0x49/0x4e kernel/locking/lockdep.c:5657
__mutex_unlock_slowpath+0x99/0x5e0 kernel/locking/mutex.c:900
rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:561
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
____sys_sendmsg+0x6e8/0x810 net/socket.c:2409
___sys_sendmsg+0xf3/0x170 net/socket.c:2463
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
[Thanks to Hawkins Jiawei and Khalid Masum for their attempts to fix this]
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Reported-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com
cc: Hawkins Jiawei <yin31149@gmail.com>
cc: Khalid Masum <khalid.masum.92@gmail.com>
cc: Dan Carpenter <dan.carpenter@oracle.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/166135894583.600315.7170979436768124075.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Properly report hw rx hash for mt7986 chipset accroding to the new dma
descriptor layout.
Fixes: 197c9e9b17b11 ("net: ethernet: mtk_eth_soc: introduce support for mt7986 chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/091394ea4e705fbb35f828011d98d0ba33808f69.1661257293.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit c078290a2b76 ("selftests: include bonding tests into the kselftest
infra") adds the bonding tests in the directory:
tools/testing/selftests/drivers/net/bonding/
The file entry in MAINTAINERS for the BONDING DRIVER however refers to:
tools/testing/selftests/net/bonding/
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken file pattern.
Repair this file entry in BONDING DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220824072945.28606-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was not possible to create 1-tuple flow director
rule for IPv6 flow type. It was caused by incorrectly
checking for source IP address when validating user provided
destination IP address.
Fix this by changing ip6src to correct ip6dst address
in destination IP address validation for IPv6 flow type.
Fixes: efca91e89b67 ("i40e: Add flow director support for IPv6")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ixgbe_ptp_start_cyclecounter is intended to be called whenever the
cyclecounter parameters need to be changed.
Since commit a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x
devices"), this function has cleared the SYSTIME registers and reset the
TSAUXC DISABLE_SYSTIME bit.
While these need to be cleared during ixgbe_ptp_reset, it is wrong to clear
them during ixgbe_ptp_start_cyclecounter. This function may be called
during both reset and link status change. When link changes, the SYSTIME
counter is still operating normally, but the cyclecounter should be updated
to account for the possibly changed parameters.
Clearing SYSTIME when link changes causes the timecounter to jump because
the cycle counter now reads zero.
Extract the SYSTIME initialization out to a new function and call this
during ixgbe_ptp_reset. This prevents the timecounter adjustment and avoids
an unnecessary reset of the current time.
This also restores the original SYSTIME clearing that occurred during
ixgbe_ptp_reset before the commit above.
Reported-by: Steve Payne <spayne@aurora.tech>
Reported-by: Ilya Evenbach <ievenbach@aurora.tech>
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
While reading sysctl_somaxconn, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading netdev_unregister_timeout_secs, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 5aa3afe107d9 ("net: make unregister netdev warning timeout configurable")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading gro_normal_batch, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 323ebb61e32b ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_devconf_inherit_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 856c395cfa63 ("net: introduce a knob to control whether to inherit devconf config")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_fb_tunnels_only_for_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 79134e6ce2c9 ("net: do not create fallback tunnels for non-default namespaces")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading netdev_budget_usecs, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 7acf8a1e8a28 ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_max_skb_frags, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 5f74f82ea34c ("net:Add sysctl_max_skb_frags")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading netdev_budget, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 51b0bdedb8e7 ("[NET]: Separate two usages of netdev_max_backlog.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_net_busy_read, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 2d48d67fa8cd ("net: poll/select low latency socket support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_net_busy_poll, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 060212928670 ("net: add low latency socket poll")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_tstamp_allow_data, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: b245be1f4db1 ("net-timestamp: no-payload only sysctl")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_optmem_max, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading rs->interval and rs->burst, they can be changed
concurrently via sysctl (e.g. net_ratelimit_state). Thus, we
need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading netdev_tstamp_prequeue, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 3b098e2d7c69 ("net: Consistent skb timestamping")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading netdev_max_backlog, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
While at it, we remove the unnecessary spaces in the doc.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading weight_p, it can be changed concurrently. Thus, we need
to add READ_ONCE() to its reader.
Also, dev_[rt]x_weight can be read/written at the same time. So, we
need to use READ_ONCE() and WRITE_ONCE() for its access. Moreover, to
use the same weight_p while changing dev_[rt]x_weight, we add a mutex
in proc_do_dev_weight().
Fixes: 3d48b53fb2ae ("net: dev_weight: TX/RX orthogonality")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_[rw]mem_(max|default), they can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_copy_bits() could fail, which requires a check on the return
value.
Signed-off-by: Li Zhong <floridsleeves@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On link state change, the controller gets reset,
causing PPS to drop out and the PHC to lose its
time and calibration. So we restart it if needed,
restoring calibration and time registers.
Changes since v2:
* Add `fec_ptp_save_state()`/`fec_ptp_restore_state()`
* Use `ktime_get_real_ns()`
* Use `BIT()` macro
Changes since v1:
* More ECR #define's
* Stop PPS in `fec_ptp_stop()`
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So add all skb to
a tmp list, then free them after spin_unlock_irqrestore() at
once.
Fixes: 66ba215cb513 ("neigh: fix possible DoS due to net iface start/stop loop")
Suggested-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, net.netfilter.nf_conntrack_frag6_high_thresh can only be lowered.
I found this issue while investigating a probable kernel issue
causing flakes in tools/testing/selftests/net/ip_defrag.sh
In particular, these sysctl changes were ignored:
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_high_thresh=9000000 >/dev/null 2>&1
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_low_thresh=7000000 >/dev/null 2>&1
This change is inline with commit 836196239298 ("net/ipfrag: let ip[6]frag_high_thresh
in ns be higher than in init_net")
Fixes: 8db3d41569bb ("netfilter: nf_defrag_ipv6: use net_generic infra")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
To clear the flow table on flow table free, the following sequence
normally happens in order:
1) gc_step work is stopped to disable any further stats/del requests.
2) All flow table entries are set to teardown state.
3) Run gc_step which will queue HW del work for each flow table entry.
4) Waiting for the above del work to finish (flush).
5) Run gc_step again, deleting all entries from the flow table.
6) Flow table is freed.
But if a flow table entry already has pending HW stats or HW add work
step 3 will not queue HW del work (it will be skipped), step 4 will wait
for the pending add/stats to finish, and step 5 will queue HW del work
which might execute after freeing of the flow table.
To fix the above, this patch flushes the pending work, then it sets the
teardown flag to all flows in the flowtable and it forces a garbage
collector run to queue work to remove the flows from hardware, then it
flushes this new pending work and (finally) it forces another garbage
collector run to remove the entry from the software flowtable.
Stack trace:
[47773.882335] BUG: KASAN: use-after-free in down_read+0x99/0x460
[47773.883634] Write of size 8 at addr ffff888103b45aa8 by task kworker/u20:6/543704
[47773.885634] CPU: 3 PID: 543704 Comm: kworker/u20:6 Not tainted 5.12.0-rc7+ #2
[47773.886745] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009)
[47773.888438] Workqueue: nf_ft_offload_del flow_offload_work_handler [nf_flow_table]
[47773.889727] Call Trace:
[47773.890214] dump_stack+0xbb/0x107
[47773.890818] print_address_description.constprop.0+0x18/0x140
[47773.892990] kasan_report.cold+0x7c/0xd8
[47773.894459] kasan_check_range+0x145/0x1a0
[47773.895174] down_read+0x99/0x460
[47773.899706] nf_flow_offload_tuple+0x24f/0x3c0 [nf_flow_table]
[47773.907137] flow_offload_work_handler+0x72d/0xbe0 [nf_flow_table]
[47773.913372] process_one_work+0x8ac/0x14e0
[47773.921325]
[47773.921325] Allocated by task 592159:
[47773.922031] kasan_save_stack+0x1b/0x40
[47773.922730] __kasan_kmalloc+0x7a/0x90
[47773.923411] tcf_ct_flow_table_get+0x3cb/0x1230 [act_ct]
[47773.924363] tcf_ct_init+0x71c/0x1156 [act_ct]
[47773.925207] tcf_action_init_1+0x45b/0x700
[47773.925987] tcf_action_init+0x453/0x6b0
[47773.926692] tcf_exts_validate+0x3d0/0x600
[47773.927419] fl_change+0x757/0x4a51 [cls_flower]
[47773.928227] tc_new_tfilter+0x89a/0x2070
[47773.936652]
[47773.936652] Freed by task 543704:
[47773.937303] kasan_save_stack+0x1b/0x40
[47773.938039] kasan_set_track+0x1c/0x30
[47773.938731] kasan_set_free_info+0x20/0x30
[47773.939467] __kasan_slab_free+0xe7/0x120
[47773.940194] slab_free_freelist_hook+0x86/0x190
[47773.941038] kfree+0xce/0x3a0
[47773.941644] tcf_ct_flow_table_cleanup_work
Original patch description and stack trace by Paul Blakey.
Fixes: c29f74e0df7a ("netfilter: nf_flow_table: hardware offload support")
Reported-by: Paul Blakey <paulb@nvidia.com>
Tested-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Expose nf_flow_table_gc_run() to force a garbage collector run from the
offload infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Update nft_data_init() to report EINVAL if chain is already bound.
Fixes: d0e2c7de92c7 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Reported-by: Gwangun Jung <exsociety@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Only allow to use this expression from NFPROTO_NETDEV family.
Fixes: af308b94a2a4 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
As it was originally intended, restrict extension to supported families.
Fixes: b96af92d6eaf ("netfilter: nf_tables: implement Passive OS fingerprint module in nft_osf")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Error might occur later in the nf_tables_addchain() codepath, enable
static key only after transaction has been created.
Fixes: 9f08ea848117 ("netfilter: nf_tables: keep chain counters away from hot path")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Instead report ERANGE if csum_offset is too long, and EOPNOTSUPP if type
is not support.
Fixes: 7ec3f7b47b8d ("netfilter: nft_payload: add packet mangling support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Instead of offset and length are truncation to u8, report ERANGE.
Fixes: 96518518cc41 ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
mutex is per-netns, move table_netns to the pernet area.
*read-write* to 0xffffffff883a01e8 of 8 bytes by task 6542 on cpu 0:
nf_tables_newtable+0x6dc/0xc00 net/netfilter/nf_tables_api.c:1221
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline]
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv+0xa6a/0x13a0 net/netfilter/nfnetlink.c:652
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x652/0x730 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x643/0x740 net/netlink/af_netlink.c:1921
Fixes: f102d66b335a ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Updates on existing implicit chain make no sense, disallow this.
Fixes: d0e2c7de92c7 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
LRO/GRO_HW should be disabled if there is an attached XDP program.
BNXT_FLAG_TPA is the current setting of the LRO/GRO_HW. Using
BNXT_FLAG_TPA to disable LRO/GRO_HW will cause these features to be
permanently disabled once they are disabled.
Fixes: 1dc4c557bfed ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are 2 issues:
1. We should decrement hw_resc->max_nqs instead of hw_resc->max_irqs
with the number of NQs assigned to the VFs. The IRQs are fixed
on each function and cannot be re-assigned. Only the NQs are being
assigned to the VFs.
2. vf_msix is the total number of NQs to be assigned to the VFs. So
we should decrement vf_msix from hw_resc->max_nqs.
Fixes: b16b68918674 ("bnxt_en: Add SR-IOV support for 57500 chips.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing devlink_set_features() API for callbacks reload_down
and reload_up to function.
Fixes: 228ea8c187d8 ("bnxt_en: implement devlink dev reload driver_reinit")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using BNXT_PAGE_MODE_BUF_SIZE + offset as buffer length value is not
sufficient when running single buffer XDP programs doing redirect
operations. The stack will complain on missing skb tail room. Fix it
by using PAGE_SIZE when calling xdp_init_buff() for single buffer
programs.
Fixes: b231c3f3414c ("bnxt: refactor bnxt_rx_xdp to separate xdp_init_buff/xdp_prepare_buff")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TPROXY is only allowed from prerouting, but nft_tproxy doesn't check this.
This fixes a crash (null dereference) when using tproxy from e.g. output.
Fixes: 4ed8eb6570a4 ("netfilter: nf_tables: Add native tproxy support")
Reported-by: Shell Chen <xierch@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
When a TCP sends more bytes than allowed by the receive window, all future
packets can be marked as invalid.
This can clog up the conntrack table because of 5-day default timeout.
Sequence of packets:
01 initiator > responder: [S], seq 171, win 5840, options [mss 1330,sackOK,TS val 63 ecr 0,nop,wscale 1]
02 responder > initiator: [S.], seq 33211, ack 172, win 65535, options [mss 1460,sackOK,TS val 010 ecr 63,nop,wscale 8]
03 initiator > responder: [.], ack 33212, win 2920, options [nop,nop,TS val 068 ecr 010], length 0
04 initiator > responder: [P.], seq 172:240, ack 33212, win 2920, options [nop,nop,TS val 279 ecr 010], length 68
Window is 5840 starting from 33212 -> 39052.
05 responder > initiator: [.], ack 240, win 256, options [nop,nop,TS val 872 ecr 279], length 0
06 responder > initiator: [.], seq 33212:34530, ack 240, win 256, options [nop,nop,TS val 892 ecr 279], length 1318
This is fine, conntrack will flag the connection as having outstanding
data (UNACKED), which lowers the conntrack timeout to 300s.
07 responder > initiator: [.], seq 34530:35848, ack 240, win 256, options [nop,nop,TS val 892 ecr 279], length 1318
08 responder > initiator: [.], seq 35848:37166, ack 240, win 256, options [nop,nop,TS val 892 ecr 279], length 1318
09 responder > initiator: [.], seq 37166:38484, ack 240, win 256, options [nop,nop,TS val 892 ecr 279], length 1318
10 responder > initiator: [.], seq 38484:39802, ack 240, win 256, options [nop,nop,TS val 892 ecr 279], length 1318
Packet 10 is already sending more than permitted, but conntrack doesn't
validate this (only seq is tested vs. maxend, not 'seq+len').
38484 is acceptable, but only up to 39052, so this packet should
not have been sent (or only 568 bytes, not 1318).
At this point, connection is still in '300s' mode.
Next packet however will get flagged:
11 responder > initiator: [P.], seq 39802:40128, ack 240, win 256, options [nop,nop,TS val 892 ecr 279], length 326
nf_ct_proto_6: SEQ is over the upper bound (over the window of the receiver) .. LEN=378 .. SEQ=39802 ACK=240 ACK PSH ..
Now, a couple of replies/acks comes in:
12 initiator > responder: [.], ack 34530, win 4368,
[.. irrelevant acks removed ]
16 initiator > responder: [.], ack 39802, win 8712, options [nop,nop,TS val 296201291 ecr 2982371892], length 0
This ack is significant -- this acks the last packet send by the
responder that conntrack considered valid.
This means that ack == td_end. This will withdraw the
'unacked data' flag, the connection moves back to the 5-day timeout
of established conntracks.
17 initiator > responder: ack 40128, win 10030, ...
This packet is also flagged as invalid.
Because conntrack only updates state based on packets that are
considered valid, packet 11 'did not exist' and that gets us:
nf_ct_proto_6: ACK is over upper bound 39803 (ACKed data not seen yet) .. SEQ=240 ACK=40128 WINDOW=10030 RES=0x00 ACK URG
Because this received and processed by the endpoints, the conntrack entry
remains in a bad state, no packets will ever be considered valid again:
30 responder > initiator: [F.], seq 40432, ack 2045, win 391, ..
31 initiator > responder: [.], ack 40433, win 11348, ..
32 initiator > responder: [F.], seq 2045, ack 40433, win 11348 ..
... all trigger 'ACK is over bound' test and we end up with
non-early-evictable 5-day default timeout.
NB: This patch triggers a bunch of checkpatch warnings because of silly
indent. I will resend the cleanup series linked below to reduce the
indent level once this change has propagated to net-next.
I could route the cleanup via nf but that causes extra backport work for
stable maintainers.
Link: https://lore.kernel.org/netfilter-devel/20220720175228.17880-1-fw@strlen.de/T/#mb1d7147d36294573cc4f81d00f9f8dadfdd06cd8
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Harshit Mogalapalli says:
In ebt_do_table() function dereferencing 'private->hook_entry[hook]'
can lead to NULL pointer dereference. [..] Kernel panic:
general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
[..]
RIP: 0010:ebt_do_table+0x1dc/0x1ce0
Code: 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 5c 16 00 00 48 b8 00 00 00 00 00 fc ff df 49 8b 6c df 08 48 8d 7d 2c 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 88
[..]
Call Trace:
nf_hook_slow+0xb1/0x170
__br_forward+0x289/0x730
maybe_deliver+0x24b/0x380
br_flood+0xc6/0x390
br_dev_xmit+0xa2e/0x12c0
For some reason ebtables rejects blobs that provide entry points that are
not supported by the table, but what it should instead reject is the
opposite: blobs that DO NOT provide an entry point supported by the table.
t->valid_hooks is the bitmask of hooks (input, forward ...) that will see
packets. Providing an entry point that is not support is harmless
(never called/used), but the inverse isn't: it results in a crash
because the ebtables traverser doesn't expect a NULL blob for a location
its receiving packets for.
Instead of fixing all the individual checks, do what iptables is doing and
reject all blobs that differ from the expected hooks.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
When a driver returns -EOPNOTSUPP in dsa_port_bridge_join() but failed
to provide a reason for it, DSA attempts to set the extack to say that
software fallback will kick in.
The problem is, when we use brctl and the legacy bridge ioctls, the
extack will be NULL, and DSA dereferences it in the process of setting
it.
Sergei Antonov proves this using the following stack trace:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
PC is at dsa_slave_changeupper+0x5c/0x158
dsa_slave_changeupper from raw_notifier_call_chain+0x38/0x6c
raw_notifier_call_chain from __netdev_upper_dev_link+0x198/0x3b4
__netdev_upper_dev_link from netdev_master_upper_dev_link+0x50/0x78
netdev_master_upper_dev_link from br_add_if+0x430/0x7f4
br_add_if from br_ioctl_stub+0x170/0x530
br_ioctl_stub from br_ioctl_call+0x54/0x7c
br_ioctl_call from dev_ifsioc+0x4e0/0x6bc
dev_ifsioc from dev_ioctl+0x2f8/0x758
dev_ioctl from sock_ioctl+0x5f0/0x674
sock_ioctl from sys_ioctl+0x518/0xe40
sys_ioctl from ret_fast_syscall+0x0/0x1c
Fix the problem by only overriding the extack if non-NULL.
Fixes: 1c6e8088d9a7 ("net: dsa: allow port_bridge_join() to override extack message")
Link: https://lore.kernel.org/netdev/CABikg9wx7vB5eRDAYtvAm7fprJ09Ta27a4ZazC=NX5K4wn6pWA@mail.gmail.com/
Reported-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20220819173925.3581871-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Aleksander Jan Bajkowski
Heiner Kallweit
R Mohamed Shah
Shannon Nelson
David Howells
Lorenzo Bianconi
Lukas Bulwahn
Sylwester Dziedziuch
Jacob Keller
Kuniyuki Iwashima
lily
Csókás Bence
Yang Yingliang
Eric Dumazet
Pablo Neira Ayuso
Vikas Gupta
Pavan Chebbi
Vladimir Oltean
Florian Westphal