| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Any CLPS711X-based board can be replaced with devicetree equivalent.
Remove the board files.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds basic support to run Cirrus Logic ARMv4T CPUs
with device-tree support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Last CLPS711X CPU register is PLLR has 0xa5a8 address, so we can reduce
the map to 48k and align the end of the static at VMALLOC_START.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Since the SP804 timer changes will not been merged upstream, switch the
default OX810SE config to the OXNAS RPS Timer driver configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Use regex pattern to match tango-specific files.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
cpu_die() and cpu_kill() are implemented in firmware.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since the initial support of mach-uniphier, this has always been
just empty.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Looks like I only partially fixed up things if CONFIG_SMP
is not set for the recent kexec changes. We don't have
boot_secondary available without SMP as reported by Arnd.
Fixes: 0573b957fc21 ("ARM: OMAP4+: Prevent CPU1 related hang with kexec")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add device tree compatible string "imx7s" for i.MX 7Solo.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Most peripherals on the i.MX51 have an Off-Platform Peripheral Access
Control Register (OPACR) in which the access rights (together with the
MPROT registers) can be declared.
However, this does not seem to work for example for SSI1+SDMA, because the
supervisor bit is not set for the SDMA unit.
A similar problem was described in the patch for i.MX53 CPU
(ARM: i.MX53: globally disable supervisor protect), and the same solution
is applicable for i.MX51 CPU.
Patch has tested on custom board based on Digi CCMX-51 module (i.MX51).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for Qualcomm MDM9615 in Kconfig and in DT match list.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The davinci-i2s driver ("davinci-mcbsp") does not use platform
data any longer. Remove the dummy pdata provided by the board
drivers dm355, dm365, dm644x and neuros-osd2.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Some of the drivers for S3C and S5P families of Samsung SoCs go in
through Samsung SoC tree. Extend the entry so proper maintainers would
be displayed in such cases, most notably the cpufreq drivers. This does
not change the work-flow for other drivers which have sub-maintainers
(like Samsung clocks).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Kexec needs omap4_cpu_kill, otherwise kexec will produce on SMP:
kexec_load failed: Invalid argument
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We need to reset CPU1 properly for kexec when booting different
kernel versions. Otherwise CPU1 will attempt to boot the the
previous kernel's start_secondary(). Note that the restctrl
register is different from the low-power mode wakeup register
CPU1_WAKEUP_NS_PA_ADDR. We need to configure both.
Let's fix the issue by defining SoC specific data to initialize
things in a more generic way. And let's also standardize omap-smp.c
to use soc_is instead of cpu_is while at it.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Kexec booted kernels on omap4 will hang early during the boot if the
booted kernel is different version from the previous kernel.
This is because the previous kernel may have configured low-power mode
using CPU1_WAKEUP_NS_PA_ADDR. In that case it points to the previous
kernel's omap4_secondary_startup(), and CPU1 can be in low power mode
from the previous kernel. When the new kernel configures the CPU1
clockdomain, CPU1 can wake from low power state prematurely during
omap44xx_clockdomains_init() running random code.
Let's fix the issue by configuring CPU1_WAKEUP_NS_PA_ADDR before we
call omap44xx_clockdomains_init(). Note that this is very early during
the init, and we will do proper CPU1 reset during SMP init a bit later
on in omap4_smp_prepare_cpus(). And we need to do this when SMP is
not enabled as the previous kernel may have had it enabled.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Prepare things for making kexec work on SMP omap variants by initializing
SARM RAM base early. This allows us to configure CPU1 for kexec in case
the previous kernel has put CPU1 in low power mode.
Note that this should not prevent moving other SAR RAM code to live
under drivers. However for kexec, we will need this very early.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per the TRM: http://www.ti.com/lit/ug/spruh73m/spruh73m.pdf
offset 0x4 is reserved for PRM_PER. Hence removing the wrongly
defined address offset.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The declaration of s5p_init_cpu() in arch/arm/mach-exynos/common.h
is not included in the platform file arch/arm/plat-samsung/cpu.c
which generates a warning.
Fix the following warning by moving the declaration to somewhere
both the machine and platform code can get to it, and including
the right files as necessary:
arch/arm/plat-samsung/cpu.c:47:13: warning: symbol 's5p_init_cpu' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The ti81xx_rtc_hwmod is not exported, or declared outside the file
arch/arm/mach-omap2/omap_hwmod_81xx_data.c so make it static to
avoid the following warning:
arch/arm/mach-omap2/omap_hwmod_81xx_data.c:246:19: warning: symbol 'ti81xx_rtc_hwmod' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
pruss hwmod RSTST register wrongly points to PWRSTCTRL register in case of
am43xx. Fix the RSTST register offset value.
This can lead to setting of wrong power state values for PER domain.
Fixes: 1c7e224d ("ARM: OMAP2+: hwmod: AM335x: runtime register update")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Exynos542x SoCs using A15+A7 can boot to A15 or A7. If it boots using
A7 (like on Odroid XU family boards), it can't choose right UART
physical address only the part number of CP15. Fix the detection logic
by checking the Cluster ID additionally.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
[k.kozlowski: Extend commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The declaration of keystone_pm_runtime_init() is not included
from keystone.h in pm_domain.c. Including the file fixes the
following sparse warning:
arch/arm/mach-keystone/pm_domain.c:37:12: warning: symbol 'keystone_pm_runtime_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Fix a pair of missing statics on un-exported functions and
include <linux/platform_data/atmel.h> to provide the declaration
of at91_suspend_entering_slow_clock() to fix the following
sparse warnings:
arch/arm/mach-at91/pm.c:127:5: warning: symbol 'at91_suspend_entering_slow_clock' was not declared. Should it be static?
arch/arm/mach-at91/pm.c:358:6: warning: symbol 'at91rm9200_idle' was not declared. Should it be static?
arch/arm/mach-at91/pm.c:367:6: warning: symbol 'at91sam9_idle' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Update the Atmel SoC entry for SAMA5D2 with all the product variants. Add the
datasheet web link, now that it's available, for instant access to full product
documentation.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The <soc/imx/cpuidle.h> file has declarations of two funcitons
exported from cpuidle-imx6q.c but it is not included. Fix the
following warnings by adding the include:
arch/arm/mach-imx/cpuidle-imx6q.c:71:6: warning: symbol 'imx6q_cpuidle_fec_irqs_used' was not declared. Should it be static?
arch/arm/mach-imx/cpuidle-imx6q.c:76:6: warning: symbol 'imx6q_cpuidle_fec_irqs_unused' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the PMU code endian access code to deal with kernels built for
big endian operation by changing the __raw IO accessors to the
_relaxed variants.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Fix the use of __raw accesors in pm-common.c to use the _relaxed
variants to deal with any issues due to endian related fetches.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Fix the PMU code endian access code to deal with kernels built for big endian
operation.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
If the kernel is built big endian, then using the __raw read and write IO
accessors is not going to work as they end up writing big-endian data to
little-endian IO registers. Fix this by using the readl and writel relaxed
versions which ensure little endian IO.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
If the system is built for big endian, then the CPU identificaiton register
will be read in the wrong order. Fix this by using readl_relaxed() on the
register.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The exynos low-level debug macros need to be fixed if the system is being
built big endian. Add the necessary endian swaps for accessing the registers
to get output working again
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
IRQ number should be translated from VIRQ to HWIRQ for TZIC.
As a solution for this issue, move existing translation code
from AVIC to common place.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
If both CONFIG_CPU_IDLE or CONFIG_SOC_IMX6Q are not set
then the imx6q_cpuidle_fec_irqs_used() and other functions
should be marked static inline to avoid the following
warnings whilst building drivers/net/ethernet/freescale:
include/soc/imx/cpuidle.h:21:6: warning: symbol 'imx6q_cpuidle_fec_irqs_used' was not declared. Should it be static?
include/soc/imx/cpuidle.h:22:6: warning: symbol 'imx6q_cpuidle_fec_irqs_unused' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Export cpuidle functions needed by fec driver to fix the issue below
seen with fec module build.
ERROR: "imx6q_cpuidle_fec_irqs_unused" [drivers/net/ethernet/freescale/fec.ko] undefined!
ERROR: "imx6q_cpuidle_fec_irqs_used" [drivers/net/ethernet/freescale/fec.ko] undefined!
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
Fix the following warning by including ../common.h to provide
the protoype for mxc_register_gpio() :
arch/arm/mach-imx/devices/platform-gpio-mxc.c:11:24: warning: symbol 'mxc_register_gpio' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following warnings by adding the include files
that define them:
arch/arm/mach-imx/devices/devices.c:25:15: warning: symbol 'mxc_aips_bus' was not declared. Should it be static?
arch/arm/mach-imx/devices/devices.c:29:15: warning: symbol 'mxc_ahb_bus' was not declared. Should it be static?
arch/arm/mach-imx/devices/devices.c:33:12: warning: symbol 'mxc_device_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX6 Q/DL has an erratum (ERR006687) that prevents the FEC from
waking the CPUs when they are in wait(unclocked) state. As the hardware
workaround isn't applicable to all boards, disable the deeper idle state
when the workaround isn't present and the FEC is in use.
This allows to safely run a kernel with CPUidle enabled on all i.MX6
boards.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net> (for network changes)
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The uvc compat ioctl implementation seems to have copied user data
for no good reason. Remove a bunch of copies.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
|
|
The current code goes through a lot of indirection just to call a
known handler. Simplify it: just call the handlers directly.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
|
|
Until now, hitting this BUG_ON caused a recursive oops (because oops
handling involves do_exit(), which calls into the scheduler, which in
turn raises an oops), which caused stuff below the stack to be
overwritten until a panic happened (e.g. via an oops in interrupt
context, caused by the overwritten CPU index in the thread_info).
Just panic directly.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This prevents users from triggering a stack overflow through a recursive
invocation of pagefault handling that involves mapping procfs files into
virtual memory.
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This prevents stacking filesystems (ecryptfs and overlayfs) from using
procfs as lower filesystem. There is too much magic going on inside
procfs, and there is no good reason to stack stuff on top of procfs.
(For example, procfs does access checks in VFS open handlers, and
ecryptfs by design calls open handlers from a kernel thread that doesn't
drop privileges or so.)
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add configuration options for the most commonly used UART physical and
virtual addresses to ease the use of DEBUG_LL and earlyprintk.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
AT91 still uses an offset (0x0100 0000) from the physical address to map
the debug UART. This is unfortunate as for some platforms (sama5d3 and
earlier), it ends up in the PCI zone and PCI is enabled in multi_v7.
Switch to DEBUG_UART_VIRT to solve that.
Tested on sama5d3 and 9g20.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The compatible device tree node that is searched for is imx6q-iomuxc-gpr
but was misspelled imx6q-iomux-gpr in the error handling message.
Signed-off-by: Jean Guyomarc'h <jean.guyomarch@openwide.fr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add clock definitions "davinci-mcbsp.0" and "davinci-mcbsp.1" in order
to make McBSP driver work on the DA850 platform.
The McBSP 0 and 1 interfaces were not defined for the DA850 platform.
Neither were the related clocks. In order to make the use of McBSP via
devicetree the clocks need to be defined.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
On a 4-socket Brickland system, hot-removing one ioapic is fine.
Hot-removing the 2nd one causes panic in mp_unregister_ioapic()
while calling release_resource().
It is because the iomem_res pointer has already been released
when removing the first ioapic.
To explain the use of &res[num] here: res is assigned to ioapic_resources,
and later in ioapic_insert_resources() we do:
struct resource *r = ioapic_resources;
for_each_ioapic(i) {
insert_resource(&iomem_resource, r);
r++;
}
Here 'r' is treated as an arry of 'struct resource', and the r++ ensures
that each element of the array is inserted separately. Thus we should call
release_resouce() on each element at &res[num].
Fix it by assigning the correct pointers to ioapics[i].iomem_res in
ioapic_setup_resources().
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: tony.luck@intel.com
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1465369193-4816-3-git-send-email-rui.y.wang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The addresses for DSS are provided in the DT data, so they can be
removed from the hwmod.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
Alexander Shiyan
Neil Armstrong
Marc Gonzalez
Masahiro Yamada
Tony Lindgren
Stefan Agner
Petr Kulhavy
Krzysztof Kozlowski
Keerthy
Ben Dooks
Joonyoung Shim
Nicolas Ferre
Shawn Guo
Linus Torvalds
Lucas Stach
Andy Lutomirski
Jann Horn
Alexandre Belloni
Jean Guyomarc'h
Rui Wang
Tomi Valkeinen