| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Recent commit has added the reservation of RSS context. This requires
bnxt_hwrm_vnic_qcaps() to be called before allocating any RSS contexts.
The bnxt_hwrm_vnic_qcaps() call sets up proper flags that will
determine how many RSS contexts to allocate to support NTUPLE.
This causes a regression that too many RSS contexts are being reserved
and causing resource shortage when enabling many VFs. Fix it by calling
bnxt_hwrm_vnic_qcaps() earlier.
Fixes: 41e8d7983752 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This issue happens when trying to add an existent tunnel. It
doesn't call sock_put() before returning -EEXIST to release
the sock refcnt that was held by calling sock_hold() before
the existence check.
This patch is to fix it by holding the sock after doing the
existence check.
Fixes: f6cd651b056f ("l2tp: fix race in duplicate tunnel detection")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMC-D stress workload showed connection stalls. Since the firmware
decides to skip raising an interrupt if the SBA DMBE mask bit is
still set, this SBA DMBE mask bit should be cleared before the
IRQ handling in the SMC code runs. Otherwise there are small windows
possible with missing interrupts for incoming data.
SMC-D currently does not care about the old value of the SBA DMBE
mask.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes: 51ff17251c9c ("qed: Add support for RoCE hw init")
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Release PTT before entering error flow.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
If sch_fq is used at ingress, skbs that might have been
timestamped by net_timestamp_set() if a packet capture
is requesting timestamps could be delayed by arbitrary
amount of time, since sch_fq time base is MONOTONIC.
Fix this problem by moving code from sch_netem.c to act_mirred.c.
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.
The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.
If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.
However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.
We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.
Fixes: 7ea817f4e832 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 37c8a5fafa3b ("kbuild: consolidate Devicetree dtb build rules")
moved the location of 'dtbs_install' target which caused dtbs to not be
installed when building debian package with 'bindeb-pkg' target. Update
the builddeb script to use the same logic that determines if there's a
'dtbs_install' target which is presence of the arch dts directory. Also,
use CONFIG_OF_EARLY_FLATTREE instead of CONFIG_OF as that's a better
indication of whether we are building dtbs.
This commit will also have the side effect of installing dtbs on any
arch that has dts files. Previously, it was dependent on whether the
arch defined 'dtbs_install'.
Fixes: 37c8a5fafa3b ("kbuild: consolidate Devicetree dtb build rules")
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit 6147b1cf19651c7de297e69108b141fb30aa2349.
The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.
Output from "strace git status -uno --porcelain":
getcwd("/tmp/linux-test", 129) = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
-1 EROFS (Read-only file system)
While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.
Fixes: 6147b1cf19651 ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Since commit b41d920acff8 ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.
Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.
Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.
Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.
Fixes: b41d920acff8 ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
|
|
The current SED_CONFIG_EXP could match to comment lines in config
fragment files, especially when CONFIG_PREFIX_ is empty. For example,
Buildroot uses empty prefixing; starting symbols with BR2_ is just
convention.
Make the sed expression more robust against false positives from
comment lines. The new sed expression matches to only valid patterns.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
|
|
TCA_FLOWER_KEY_ENC_OPTS and TCA_FLOWER_KEY_ENC_OPTS_MASK can only
currently contain further nested attributes, which are parsed by
hand, so the policy is never actually used resulting in a W=1
build warning:
net/sched/cls_flower.c:492:1: warning: ‘enc_opts_policy’ defined but not used [-Wunused-const-variable=]
enc_opts_policy[TCA_FLOWER_KEY_ENC_OPTS_MAX + 1] = {
Add the validation anyway to avoid potential bugs when other
attributes are added and to make the attribute structure slightly
more clear. Validation will also set extact to point to bad
attribute on error.
Fixes: 0a6e77784f49 ("net/sched: allow flower to match tunnel options")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reserved variable should be named reserved1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only first fragment has the sport/dport information,
not the following ones.
If we want consistent hash for all fragments, we need to
ignore ports even for first fragment.
This bug is visible for IPv6 traffic, if incoming fragments
do not have a flow label, since skb_get_hash() will give
different results for first fragment and following ones.
It is also visible if any routing rule wants dissection
and sport or dport.
See commit 5e5d6fed3741 ("ipv6: route: dissect flow
in input path if fib rules need it") for details.
[edumazet] rewrote the changelog completely.
Fixes: 06635a35d13d ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.
sysctl call stack -
<6> Unable to handle kernel NULL pointer dereference at
virtual address 00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2> rmnet_vnd_get_iflink+0x1c/0x28
<2> inet6_fill_ifinfo+0x15c/0x234
<2> inet6_ifinfo_notify+0x68/0xd4
<2> ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2> proc_sys_call_handler+0xac/0x100
<2> proc_sys_write+0x3c/0x4c
<2> __vfs_write+0x54/0x14c
<2> vfs_write+0xcc/0x188
<2> SyS_write+0x60/0xc0
<2> el0_svc_naked+0x34/0x38
device register call stack -
<2> notifier_call_chain+0x84/0xbc
<2> raw_notifier_call_chain+0x38/0x48
<2> call_netdevice_notifiers_info+0x40/0x70
<2> call_netdevice_notifiers+0x38/0x60
<2> register_netdevice+0x29c/0x3d8
<2> rmnet_vnd_newlink+0x68/0xe8
<2> rmnet_newlink+0xa0/0x160
<2> rtnl_newlink+0x57c/0x6c8
<2> rtnetlink_rcv_msg+0x1dc/0x328
<2> netlink_rcv_skb+0xac/0x118
<2> rtnetlink_rcv+0x24/0x30
<2> netlink_unicast+0x158/0x1f0
<2> netlink_sendmsg+0x32c/0x338
<2> sock_sendmsg+0x44/0x60
<2> SyS_sendto+0x150/0x1ac
<2> el0_svc_naked+0x34/0x38
Fixes: b752eff5be24 ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX Checksum offloads could not be configured and ignored netdev features
flag for checksumming.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets with marked invalid IP/UDP/TCP checksums were considered as good
by the driver. The error was in a logic, processing offload bits in
RX descriptor.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed a condition mistake due to which macvlans unicast
item number 32 was not added in the unicast filter.
The consequence is that when exactly 32 macvlans are created
on NIC, the last created macvlan receives no traffic because
its MAC was not registered in HW.
Fixes: 94b3b542303f ("net: aquantia: vlan unicast address list correct handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IOMMU fault may occurr on unbind/bind or if_down/if_up sequence.
Although driver disables the rings on down, this is not enough.
Due to internal HW design, during subsequent initialization
NIC sometimes may reuse RX descriptors cache and write to the
host memory from the descriptor cache.
That's get catched by IOMMU on host.
This patch invalidates the descriptor cache in NIC on interface down
to prevent writing to the cached descriptors and to the memory pointed
in those descriptors.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flow control statuses were not synchronized between blocks,
that caused packets/link drop on some corner cases, when
MAC sent PFC although Phy was not expecting these to come.
Driver should readout the negotiated FC from phy and
configure RX block accordigly.
This is done on each link change event with information from FW.
Fixes: 288551de45aa ("net: aquantia: Implement rx/tx flow control ethtools callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device tree node name are not supposed to have "_" in them so fix the
node name use of xo_board to xo-board
Fixes: 652f1813c113 ("clk: qcom: gcc: Add global clock controller driver for QCS404")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When running function tracing on a Linux guest running on VMware
Workstation, the guest would crash. This is due to tracing of the
sched_clock internal call of the VMware vmware_sched_clock(), which
causes an infinite recursion within the tracing code (clock calls must
not be traced).
Make vmware_sched_clock() not traced by ftrace.
Fixes: 80e9a4f21fd7c ("x86/vmware: Add paravirt sched clock")
Reported-by: GwanYeong Kim <gy741.kim@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Alok Kataria <akataria@vmware.com>
CC: GwanYeong Kim <gy741.kim@gmail.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
CC: Thomas Gleixner <tglx@linutronix.de>
CC: virtualization@lists.linux-foundation.org
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20181109152207.4d3e7d70@gandalf.local.home
|
|
Latest NVIDIA GPU cards have a Cypress CCGx Type-C controller
over I2C interface.
This UCSI I2C driver uses I2C bus driver interface for communicating
with Type-C controller.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch fixes an issue that the sci_remove() could not remove
dev_attr_rx_fifo_timeout because uart_remove_one_port() set
the port->port.type to PORT_UNKNOWN.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Fixes: 5d23188a473d ("serial: sh-sci: make RX FIFO parameters tunable via sysfs")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sparse rightfully says:
warning: symbol 'gpu_i2c_driver_pm' was not declared. Should it be static?
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Latest NVIDIA GPU card has USB Type-C interface. There is a
Type-C controller which can be accessed over I2C.
This driver adds I2C bus driver to communicate with Type-C controller.
I2C client driver will be part of USB Type-C UCSI driver.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: kept Makefile sorting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to Ted Ts'o ext4_getblk() called in ext4_xattr_inode_write()
should not return bh = NULL
The only time that bh could be NULL, then, would be in the case of
something really going wrong; a programming error elsewhere (perhaps a
wild pointer dereference) or I/O error causing on-disk file system
corruption (although that would be highly unlikely given that we had
*just* allocated the blocks and so the metadata blocks in question
probably would still be in the cache).
Fixes: e50e5129f384 ("ext4: xattr-in-inode support")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org # 4.13
|
|
Currently, in case of bus error, driver will generate error message and put
in the tail of the message queue. To avoid confusions, this change should
place the bus related messages in proper order.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This function has nothing todo with error.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Current flexcan driver will put TX-ECHO in regular unsorted way, in
this case TX-ECHO can come after the response to the same TXed message.
In some cases, for example for J1939 stack, things will break.
This patch is using new rx-offload API to put the messages just in the
right place.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.
Enabling runtime PM for inactive device (a98000.i2c) with active children
[...]
Call trace:
pm_runtime_enable+0xd8/0xf8
geni_i2c_probe+0x440/0x460
platform_drv_probe+0x74/0xc8
[...]
Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add separate entry for i2c-omap and add my name as maintainer for this
driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Allow I2C_OMAP to be built for K3 platforms.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
AM654 SoCs have same I2C IP as OMAP SoCs. Add new compatible to
handle AM654 SoCs. While at that reformat the existing compatible list
for older SoCs to list one valid compatible per line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Current CAN framework can't guarantee proper/chronological order
of RX and TX-ECHO messages. To make this possible, drivers should use
this functions instead of can_get_echo_skb().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Prior to echoing a successfully transmitted CAN frame (by calling
can_get_echo_skb()), CAN drivers have to put the CAN frame (by calling
can_put_echo_skb() in the transmit function). These put and get function
take an index as parameter, which is used to identify the CAN frame.
A driver calling can_get_echo_skb() with a index not pointing to a skb
is a BUG, so add an appropriate error message.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the "struct can_priv::echo_skb" is accessed out of bounds would lead
to a kernel crash. Better print a sensible warning message instead and
try to recover.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch replaces the use of "struct can_frame::can_dlc" by "struct
canfd_frame::len" to access the frame's length. As it is ensured that
both structures have a compatible memory layout for this member this is
no functional change. Futher, this compatibility is documented in a
comment.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch factors out all non sending parts of can_get_echo_skb() into
a seperate function __can_get_echo_skb(), so that it can be re-used in
an upcoming patch.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The previous patch changes the TX path to always use the last mailbox
regardless of the used offload scheme (rx-fifo or timestamp based). This
means members "tx_mb" and "tx_mb_idx" of the struct flexcan_priv don't
depend on the offload scheme, so replace them by compile time constants.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Essentially this patch moves the TX mailbox to position 63, regardless
of timestamp based offloading or RX FIFO. So mainly the iflag register
usage regarding TX has changed. The rest is consolidating RX FIFO and
timestamp offloading as they now use both the same TX mailbox.
The reason is a very annoying behavior regarding sending RTR frames when
_not_ using RX FIFO:
If a TX mailbox sent a RTR frame it becomes a RX mailbox. For that
reason flexcan_irq disables the TX mailbox again. But if during the time
the RTR was sent and the TX mailbox is disabled a new CAN frames is
received, it is lost without notice. The reason is that so-called
"Move-in" process starts from the lowest mailbox which happen to be a TX
mailbox set to EMPTY.
Steps to reproduce (I used an imx7d):
1. generate regular bursts of messages
2. send a RTR from flexcan with higher priority than burst messages every
1ms, e.g. cangen -I 0x100 -L 0 -g 1 -R can0
3. notice a lost message without notification after some seconds
When running an iperf in parallel this problem is occurring even more
frequently. Using filters is not possible as at least one single CAN-ID
is allowed. Handling the TX MB during RX is also not possible as there
is no race-free disable of RX MB.
There is still a slight window when the described problem can occur. But
for that all RX MB must be in use which is essentially next to an
overrun. Still there will be no indication if it ever occurs.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Unlock the MB irrespective of reception method being FIFO or timestamp
based. It is optional but recommended to unlock Mailbox as soon as
possible and make it available for reception.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Document RZ/G2M (r8a774a1) SoC specific bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes: 862e2b6af9413b43 ("can: rcar_can: support all input clocks")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
Michael Chan
Xin Long
Ursula Braun
Denis Bolotin
Michal Kalderon
Sudarsana Reddy Kalluru
Linus Torvalds
Eric Dumazet
Andrew Lunn
Jon Maloy
Rob Herring
Guenter Roeck
Masahiro Yamada
Jakub Kicinski
Alexandre Belloni
배석진
Subash Abhinov Kasiviswanathan
Dmitry Bogdanov
Igor Russkikh
Vinod Koul
Steven Rostedt (VMware)
Ajay Gupta
Yoshihiro Shimoda
Wolfram Sang
Vasily Averin
Oleksij Rempel
Stephen Boyd
Vignesh R
Marc Kleine-Budde
Alexander Stein
Pankaj Bansal
Lukas Wunner
Fabrizio Castro