| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
failed to configure the page size for architectures with page size
different than 4K.
Fixes: 938fe83 ("net/mlx5_core: New device capabilities handling")
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are paths in the driver such as an unrecoverable error (UE) detection
followed by a driver unload wherein be_clear() is invoked twice.
Individual data structures are reset so that they are not cleaned/freed
twice. This patch does the same for eqo->affinity_mask. It is freed only
if EQs haven't yet been destroyed. This fixes a possible crash when
affinity_mask is freed twice.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An RX stall issue was seen on Lancer adapters, when RXQs are destroyed
while they are in an "out of buffer" state. This patch fixes this issue
by posting 64 buffers to each RXQ before destroying them in the close path.
This is done after ensuring that no more new packets are selected for
transfer to the RXQs by disabling interface filters.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW issues were observed on Lancer adapters if IFACE filters
(flags, mac addrs etc) are enabled *before* creating RXQs. This patch
changes the driver design by enabling filters in be_open() --
instead of be_setup() -- after RXQs are created and buffers posted.
Two new wrapper functions, be_enable_if_filters() and
be_disable_if_filters() are introduced to enable/disable IFACE filters in
be_open()/be_close() respectively. In be_setup() the IFACE is now created
only with the RSS flag.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
virtio declares support for NETIF_F_FRAGLIST, but assumes
that there are at most MAX_SKB_FRAGS + 2 fragments which isn't
always true with a fraglist.
A longer fraglist in the skb will make the call to skb_to_sgvec overflow
the sg array, leading to memory corruption.
Drop NETIF_F_FRAGLIST so we only get what we can handle.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch b1c17215d718: "stmmac: add ipq806x glue layer", leads to the
following static checker warning:
.../stmmac/dwmac-ipq806x.c:314 ipq806x_gmac_probe()
warn: double left shift '1 << (1 << gmac->id)'
The NSS_COMMON_CLK_SRC_CTRL_OFFSET macro is used once as an offset, and
once as a mask, which is a bug indeed. We'll fix it by defining the
offset as the real offset value and computing the mask from it when
required.
Tested on IPQ806x ref designs AP148 & DB149.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch, rx buffer size for each rx queue
of an interface is configurable through dts bindings.
But for an interface, the first rx queue's rx buffer
size is always the usual MTU size (plus usual overhead)
and page size for the remaining rx queues (if they are
enabled by specifying a non-zero rx queue depth dts
binding of the corresponding interface). This patch
removes the rx buffer size configuration capability.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As well as for kernels built only for ThunderX ARCH_THUNDERX is also enabled
for kernels which support multiple platforms (such as distro kernels). Thus
"default ARCH_THUNDER" is inappropriate.
I believe default m is equally frowned upon, so remove the line completely
rather than "default m if ARCH_THUNDER".
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Derek Chickles <derek.chickles@caviumnetworks.com>
Cc: Satanand Burla <satananda.burla@caviumnetworks.com>
Cc: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Cc: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enforcing this flag in RxConfig for the mentioned chips fixes netdev
watchdog issues prepended with AMD IOMMU message(s) like:
AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x001d address=0x0000000000003000 flags=0x0050]
Note that this flag is also set in Realtek's own driver for these chips.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Alexander Lindqvist <alexander@bitspace.se>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The attribute size wasn't accounted for in the get_slave_size() callback
(br_port_get_slave_size) when it was introduced, so fix it now. Also add
a policy entry for it in br_port_policy.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: 842a9ae08a25 ("bridge: Extend Proxy ARP design to allow optional rules for Wi-Fi")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The attribute size wasn't accounted for in the get_slave_size() callback
(br_port_get_slave_size) when it was introduced, so fix it now. Also add
a policy entry for it in br_port_policy.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: 958501163ddd ("bridge: Add support for IEEE 802.11 Proxy ARP")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1fbe4b46caca "net: pktgen: kill the Wait for kthread_stop
code in pktgen_thread_worker()" removed (in particular) the final
__set_current_state(TASK_RUNNING) and I didn't notice the previous
set_current_state(TASK_INTERRUPTIBLE). This triggers the warning
in __might_sleep() after return.
Afaics, we can simply remove both set_current_state()'s, and we
could do this a long ago right after ef87979c273a2 "pktgen: better
scheduler friendliness" which changed pktgen_thread_worker() to
use wait_event_interruptible_timeout().
Reported-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Waking the dealloc thread before decrementing inflight_packets is racy
because it means the thread may go to sleep before inflight_packets is
decremented. If kthread_stop() has already been called, the dealloc
thread may wait forever with nothing to wake it. Instead, wake the
thread only after decrementing inflight_packets.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 738ac1ebb96d02e0d23bc320302a6ea94c612dec ("net: Clone
skb before setting peeked flag") introduced a use-after-free bug
in skb_recv_datagram. This is because skb_set_peeked may create
a new skb and free the existing one. As it stands the caller will
continue to use the old freed skb.
This patch fixes it by making skb_set_peeked return the new skb
(or the old one if unchanged).
Fixes: 738ac1ebb96d ("net: Clone skb before setting peeked flag")
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Brenden Blanco <bblanco@plumgrid.com>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.
Fix this by initializing the refcount to be coherent with the initial
device status.
Fixes:
8fff755e9f8 (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this initialization, gateways which actually announce up/down
bandwidth of 0/0 could be added. If these nodes get purged via
_batadv_purge_orig() later, the gw_node structure does not get removed
since batadv_gw_node_delete() updates the gw_node with up/down
bandwidth of 0/0, and the updating function then discards the change
and does not free gw_node.
This results in leaking the gw_node structures, which references other
structures: gw_node -> orig_node -> orig_node_ifinfo -> hardif. When
removing the interface later, the open reference on the hardif may cause
hangs with the infamous "unregister_netdevice: waiting for mesh1 to
become free. Usage count = 1" message.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
The tt_local_entry deletion performed in batadv_tt_local_remove() was neither
protecting against simultaneous deletes nor checking whether the element was
still part of the list before calling hlist_del_rcu().
Replacing the hlist_del_rcu() call with batadv_hash_remove() provides adequate
protection via hash spinlocks as well as an is-element-still-in-hash check to
avoid 'blind' hash removal.
Fixes: 068ee6e204e1 ("batman-adv: roaming handling mechanism redesign")
Reported-by: alfonsname@web.de
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
batadv_softif_vlan_get() may return NULL which has to be verified
by the caller.
Fixes: 35df3b298fc8 ("batman-adv: fix TT VLAN inconsistency on VLAN re-add")
Reported-by: Ryan Thompson <ryan@eero.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
When a node running DAT receives an ARP request from the LAN for the
first time, it is likely that this node will request the ARP entry
through the distributed ARP table (DAT) in the mesh.
Once a DAT reply is received the asking node must check if the MAC
address for which the IP address has been asked is local. If it is, the
node must drop the ARP reply bceause the client should have replied on
its own locally.
Forwarding this reply means fooling any L2 bridge (e.g. Ethernet
switches) lying between the batman-adv node and the LAN. This happens
because the L2 bridge will think that the client sending the ARP reply
lies somewhere in the mesh, while this node is sitting in the same LAN.
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Determine if a fraglist is needed in the tx path, and allocate it if
necessary before setting up the copy and map operations.
Otherwise, undoing the copy and map operations is tricky.
This fixes a use-after-free: if allocating the fraglist failed, the copy
and map operations that had been set up were still executed, writing
over the data area of a freed skb.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multicast dst are not cached. They carry DST_NOCACHE.
As mentioned in commit f8864972126899 ("ipv4: fix dst race in
sk_dst_get()"), these dst need special care before caching them
into a socket.
Caching them is allowed only if their refcnt was not 0, ie we
must use atomic_inc_not_zero()
Also, we must use READ_ONCE() to fetch sk->sk_rx_dst, as mentioned
in commit d0c294c53a771 ("tcp: prevent fetching dst twice in early demux
code")
Fixes: 421b3885bf6d ("udp: ipv4: Add udp early demux")
Tested-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Reported-by: Alex Gartrell <agartrell@fb.com>
Cc: Michal Kubeček <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When vortex_up is failed, the skb buffers allocated by __netdev_alloc_skb
in vortex_open are not released, which may cause resource leaks.
This bug has been submitted before.
This patch modifies the error handling code to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"len" is a signed integer. We check that len is not negative, so it
goes from zero to INT_MAX. PAGE_SIZE is unsigned long so the comparison
is type promoted to unsigned long. ULONG_MAX - 4095 is a higher than
INT_MAX so the condition can never be true.
I don't know if this is harmful but it seems safe to limit "len" to
INT_MAX - 4095.
Fixes: a8c879a7ee98 ('RDS: Info and stats')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we share an action within a filter, the bind refcnt
should increase, therefore we should not call tcf_hash_release().
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
openvswitch modifies the L4 checksum of a packet when modifying
the ip address. When an IP packet is fragmented only the first
fragment contains an L4 header and checksum. Prior to this change
openvswitch would modify all fragments, modifying application data
in non-first fragments, causing checksum failures in the
reassembled packet.
Signed-off-by: Glenn Griffin <ggriffin.kernel@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver code allows for the disabling of MSI interrupts; however the
module_parm line was missed and the option fails to show with modinfo.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.15+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Alex reported the following crash when using fq_codel
with htb:
crash> bt
PID: 630839 TASK: ffff8823c990d280 CPU: 14 COMMAND: "tc"
[... snip ...]
#8 [ffff8820ceec17a0] page_fault at ffffffff8160a8c2
[exception RIP: htb_qlen_notify+24]
RIP: ffffffffa0841718 RSP: ffff8820ceec1858 RFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff88241747b400
RDX: ffff88241747b408 RSI: 0000000000000000 RDI: ffff8811fb27d000
RBP: ffff8820ceec1868 R8: ffff88120cdeff24 R9: ffff88120cdeff30
R10: 0000000000000bd4 R11: ffffffffa0840919 R12: ffffffffa0843340
R13: 0000000000000000 R14: 0000000000000001 R15: ffff8808dae5c2e8
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#9 [...] qdisc_tree_decrease_qlen at ffffffff81565375
#10 [...] fq_codel_dequeue at ffffffffa084e0a0 [sch_fq_codel]
#11 [...] fq_codel_reset at ffffffffa084e2f8 [sch_fq_codel]
#12 [...] qdisc_destroy at ffffffff81560d2d
#13 [...] htb_destroy_class at ffffffffa08408f8 [sch_htb]
#14 [...] htb_put at ffffffffa084095c [sch_htb]
#15 [...] tc_ctl_tclass at ffffffff815645a3
#16 [...] rtnetlink_rcv_msg at ffffffff81552cb0
[... snip ...]
As Jamal pointed out, there is actually no need to call dequeue
to purge the queued skb's in reset, data structures can be just
reset explicitly. Therefore, we reset everything except config's
and stats, so that we would have a fresh start after device flipping.
Fixes: 4b549a2ef4be ("fq_codel: Fair Queue Codel AQM")
Reported-by: Alex Gartrell <agartrell@fb.com>
Cc: Alex Gartrell <agartrell@fb.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
[xiyou.wangcong@gmail.com: added codel_vars_init() and qdisc_qstats_backlog_dec()]
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing a port's netdevice in 'rocker_remove_ports', we should
also free the allocated 'net_device' structure. Do that by calling
'free_netdev' after unregistering it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 4b8ac9660af ("rocker: introduce rocker switch driver")
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 50649ab14982 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab14982 back.
This fixes the following errors when used as a module:
stmmac_platform: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
stmmac_platform: Unknown symbol devm_kmalloc (err 0)
stmmac_platform: Unknown symbol stmmac_suspend (err 0)
stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
stmmac_platform: Unknown symbol platform_get_resource (err 0)
stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
stmmac_platform: Unknown symbol of_alias_get_id (err 0)
stmmac_platform: Unknown symbol stmmac_resume (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)
Fixes: 50649ab14982 ("stmmac: drop driver from stmmac platform code")
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.
The bflock is obviously obsoleted, its utility has been corroded
over time. The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines. The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device. With these changes, the TX processing is stopped before
gfar_halt().
Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume. Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.
Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)
Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CC drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
static void lock_tx_qs(struct gfar_private *priv)
^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
static void unlock_tx_qs(struct gfar_private *priv)
^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we share an action within a filter, the bind refcnt
should increase, therefore we should not call tcf_hash_release().
Fixes: 1a29321ed045 ("net_sched: act: Dont increment refcnt on replace")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the grouping of multi-function devices a non-ATS
capable device might also end up in the same domain as an
IOMMUv2 capable device.
So handle this situation gracefully and don't consider it a
bug anymore.
Tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In commit 33511b157bbcebaef853cc1811992b664a2e5862 ("rtlwifi: add support to
send beacon frame"), the mechanism for sending beacons was established. That
patch works correctly for rtl8192cu, but there is a possibility of getting
the following warnings in the PCI drivers:
WARNING: CPU: 1 PID: 2439 at net/mac80211/driver-ops.h:12
ieee80211_bss_info_change_notify+0x179/0x1d0 [mac80211]()
wlp5s0: Failed check-sdata-in-driver check, flags: 0x0
The warning is followed by a NULL pointer dereference as follows:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000006
IP: [<ffffffffc073998e>] rtl_get_tcb_desc+0x5e/0x760 [rtlwifi]
This problem was reported at http://thread.gmane.org/gmane.linux.kernel.wireless.general/138645,
but no solution was found at that time.
The problem was also reported at https://bugzilla.kernel.org/show_bug.cgi?id=9744
and this solution was developed and tested there.
The USB driver works with a NULL final argument in the adapter_tx() callback;
however, the PCI drivers need a struct rtl_tcb_desc in that position.
Fixes: 33511b157bbc ("rtlwifi: add support to send beacon frame.")
Signed-off-by: Luis Felipe Dominguez Vega <lfdominguez@nauta.cu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On the 2GHz and and on the 5GHZ band only the extpa_gain setting from
the 5GHz band was checked. this patch makes it check the property from
the correct band.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes commit eae79b4f3e82 ("rsi: fix memory leak in rsi_load_ta_instructions()")
which stopped the driver from functioning.
Firmware data has been allocated using vmalloc(), resulting in memory
that cannot be used for DMA. Hence the firmware was first copied to a
buffer allocated with kmalloc() in the original code. This patch reverts
the commit and only calls "kfree()" to release the buffer after sending
the data. This fixes the memory leak without breaking the driver.
Add a comment to the kmemdup() calls to explain why this is done, and abort
if memory allocation fails.
Tested on a Topic Miami-Florida board which contains the rsi SDIO chip.
Also added the same kfree() call to the USB glue driver. This was not
tested on actual hardware though, as I only have the SDIO version.
Fixes: eae79b4f3e82 ("rsi: fix memory leak in rsi_load_ta_instructions()")
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The newsk returned by sk_clone_lock should hold a get_net()
reference if, and only if, the parent is not a kernel socket
(making this similar to sk_alloc()).
E.g,. for the SYN_RECV path, tcp_v4_syn_recv_sock->..inet_csk_clone_lock
sets up the syn_recv newsk from sk_clone_lock. When the parent (listen)
socket is a kernel socket (defined in sk_alloc() as having
sk_net_refcnt == 0), then the newsk should also have a 0 sk_net_refcnt
and should not hold a get_net() reference.
Fixes: 26abe14379f8 ("net: Modify sk_alloc to not reference count the
netns of kernel sockets.")
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 55334a5db5cd ("net_sched: act: refuse to remove bound action
outside"), we end up with a wrong reference count for a tc action.
Test case 1:
FOO="1,6 0 0 4294967295,"
BAR="1,6 0 0 4294967294,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 \
action bpf bytecode "$FOO"
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 1 bind 1
tc actions replace action bpf bytecode "$BAR" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967294' default-action pipe
index 1 ref 2 bind 1
tc actions replace action bpf bytecode "$FOO" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 3 bind 1
Test case 2:
FOO="1,6 0 0 4294967295,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 2 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 3 bind 1
What happens is that in tcf_hash_check(), we check tcf_common for a given
index and increase tcfc_refcnt and conditionally tcfc_bindcnt when we've
found an existing action. Now there are the following cases:
1) We do a late binding of an action. In that case, we leave the
tcfc_refcnt/tcfc_bindcnt increased and are done with the ->init()
handler. This is correctly handeled.
2) We replace the given action, or we try to add one without replacing
and find out that the action at a specific index already exists
(thus, we go out with error in that case).
In case of 2), we have to undo the reference count increase from
tcf_hash_check() in the tcf_hash_check() function. Currently, we fail to
do so because of the 'tcfc_bindcnt > 0' check which bails out early with
an -EPERM error.
Now, while commit 55334a5db5cd prevents 'tc actions del action ...' on an
already classifier-bound action to drop the reference count (which could
then become negative, wrap around etc), this restriction only accounts for
invocations outside a specific action's ->init() handler.
One possible solution would be to add a flag thus we possibly trigger
the -EPERM ony in situations where it is indeed relevant.
After the patch, above test cases have correct reference count again.
Fixes: 55334a5db5cd ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this
seems not working correctly, a fix for pin NID 0x15 is needed in
addition. It's equivalent with the fixup for MacBook Air 1,1, so use
this instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131
Reported-and-tested-by: Jeffery Miller <jefferym@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The stuck queue detection mechanism allows to detect queues
that are stuck. For sleeping clients, a queue may rightfully
be stuck: if a poor client implementation stays asleep for
more than 10s, then we don't want to trigger recovery flows
because of that client.
In order to cope with this, I added a mechanism that
monitors the state of the client: when a client goes to
sleep, the timer of his queues is frozen. When he wakes up,
the timer is reset to the right value so that if a client
was awake for more than 10s and the queues are stuck, only
then, the recovery flow will kick in.
This is valid only on non-shared queues: A-MPDU queues.
There was a bug in case we Tx to a sleeping client that has
an empty A-MPDU queue: the timer was armed to now + 10s.
This is bad, but pretty harmless.
The problem is that when the client wakes up, the timer is
modified to be now + remainder. But remainder is 0 since the
queue was empty when that client went to sleep...
Fix this by checking the state of the client before playing
with the timer when we add a packet to an empty queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The old style of memory interleaving swizzled upto the end of the
first even bank of memory, and then used the remainder as unswizzled on
the unpaired bank - i.e. swizzling is not constant for all memory. This
causes problems when we try to migrate memory and so the kernel prevents
migration at all when we detect L-shaped inconsistent swizzling.
However, this issue also extends to userspace who try to manually detile
into memory as the swizzling for an individual page is unknown (it
depends on its physical address only known to the kernel), userspace
cannot correctly swizzle.
Note that this is a new attempt for the previously merged one,
reverted in
commit d82c0ba6e306f079407f07003e53c262d683397b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 14 12:29:27 2015 +0200
Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"
This is cc: stable since we need it to fix up troubles with wc cpu
mmaps that userspace recently started to use widely.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91105
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[danvet: Add note about previous (failed attempt).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the device does not support the aliasing ppgtt, we must translate
user bind requests (PIN_USER) from LOCAL_BIND to a GLOBAL_BIND. However,
since this is device specific we cannot do this conveniently in the
upper layers and so must manage the vma->bound flags in the backend.
Partial revert of commit 75d04a3773ecee617847de963ae4195d6aa74c28 [4.2-rc1]
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Apr 28 17:56:17 2015 +0300
drm/i915/gtt: Allocate va range only if vma is not bound
Note this was spotted by Daniel originally, but we dropped the ball in
getting the fix in before the bug going wild. Sorry all.
Reported-by: Vincent Legoll vincent.legoll@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91133
References: https://bugs.freedesktop.org/show_bug.cgi?id=90224
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Some AMD systems also have non-PCI devices which can do DMA.
Those can't be handled by the AMD IOMMU, as the hardware can
only handle PCI. These devices would end up with no dma_ops,
as neither the per-device nor the global dma_ops will get
set. SWIOTLB provides global dma_ops when it is active, so
make sure there are global dma_ops too when swiotlb is
disabled.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In passthrough mode (iommu=pt) all devices are identity
mapped. If a device does not support 64bit DMA it might
still need remapping. Make sure swiotlb is initialized to
provide this remapping.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since devices with IOMMUv2 functionality might be in the
same group as devices without it, allow those devices in
IOMMUv2 domains too.
Otherwise attaching the group with the IOMMUv2 device to the
domain will fail.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Remove the AMD IOMMU driver implementation for passthrough
mode and rely on the new iommu core features for that.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since the conversion to default domains the
iommu_attach_device function only works for devices with
their own group. But this isn't always true for current
IOMMUv2 capable devices, so use iommu_attach_group instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
Carol L Soto
Kalesh AP
Jason Wang
Mathieu Olivari
WingMan Kwok
Ian Campbell
Ivan Vecera
Nikolay Aleksandrov
Oleg Nesterov
Ross Lagerwall
Herbert Xu
Lucas Stach
Simon Wunderlich
Marek Lindner
Antonio Quartulli
Eric Dumazet
Jia-Ju Bai
Dan Carpenter
WANG Cong
Glenn Griffin
Larry Finger
Eric Dumazet
Ido Schimmel
Joachim Eastwood
Claudiu Manoil
Joerg Roedel
Luis Felipe Dominguez Vega
Hauke Mehrtens
Mike Looijmans
Sowmini Varadhan
Daniel Borkmann
hayeswang
Takashi Iwai
Emmanuel Grumbach
Chris Wilson