| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add IP generic TX checksum offload functionality.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In Xen environment, if Xen-swiotlb is enabled, ixgbe driver
could possibly allocate a page, DMA memory buffer, for the first
fragment which is not suitable for Xen-swiotlb to do DMA operations.
Xen-swiotlb have to internally allocate another page for doing DMA
operations. This mechanism requires syncing the data from the internal
page to the page which ixgbe sends to upper network stack. However,
since commit f3213d932173 ("ixgbe: Update driver to make use of DMA
attributes in Rx path"), the unmap operation is performed with
DMA_ATTR_SKIP_CPU_SYNC. As a result, the sync is not performed.
Since the sync isn't performed, the upper network stack could receive
a incomplete network packet. By incomplete, it means the linear data
on the first fragment(between skb->head and skb->end) is invalid. So
we have to copy the data from the internal xen-swiotlb page to the page
which ixgbe sends to upper network stack through the sync operation.
More details from Alexander Duyck:
Specifically since we are mapping the frame with
DMA_ATTR_SKIP_CPU_SYNC we have to unmap with that as well. As a result
a sync is not performed on an unmap and must be done manually as we
skipped it for the first frag. As such we need to always sync before
possibly performing a page unmap operation.
Fixes: f3213d932173 ("ixgbe: Update driver to make use of DMA attributes in Rx path")
Signed-off-by: Firo Yang <firo.yang@suse.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit
'5098850c9b9b ("i40e/i40evf: i40e_register.h updates")'
it is no longer possible to trigger an EMP Reset from debugfs, but it's
possible to request it either way, to end up with a bad reset request:
echo empr > /sys/kernel/debug/i40e/0002\:01\:00.1/command
i40e 0002:01:00.1: debugfs: forcing EMPR
i40e 0002:01:00.1: bad reset request 0x00010000
So let's remove this piece of code and show the available valid commands
as it is when any invalid command is issued.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are several uses of hw_dbg in the code, producing no output. This
patch implements it using dev_debug.
Initially the intention was to implement it using netdev_dbg, analogously
to what is done in ixgbe for instance. That approach was avoided due to
some early usages of hw_dbg, like i40e_pf_reset, before the VSI structure
initialization causing NULL pointer dereference during the driver probe if
the debug messages were turned on as soon as the module is probed.
v2:
- Use dev_dbg instead of pr_debug, and take advantage of dev_name
instead of crafting pretty much the same device name locally as suggested
by Jakub Kicinski.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The mentioned function references a i40e_hw attribute, as parameter for
hw_dbg, but it doesn't exist in the function scope.
Fixes it by changing parameters from i40e_hmc_info to i40e_hw which can
retrieve the necessary i40e_hmc_info.
v2:
- Fixed reverse xmas tree code style issue as suggested by Jakub Kicinski
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PCIe device control 2 defines does not use internally.
This patch comes to clean up those.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Allow the VF to override the "permanent" MAC address set by the host.
This allows bonding to work in the case where the administrator has set
the VF MAC.
Note that the VF must still be set to Trusted on the host if this change
is to be accepted by the PF driver.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add NVM checksum validation during probe functionality.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the function fm10k_xmit_frame_ring, we recently switched to using
the skb_frag_size accessor instead of directly using the size member of
the skb fragment.
This made the for loop slightly harder to read because it created a very
long line that is difficult to split up. Avoid this by using a local
variable in the for loop, so that we do not have to break the line on an
open parenthesis.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Update the LAN driver documentation to include the latest feature
implementation and driver capabilities.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
|
|
Move igc_phy_setup_autoneg, igc_wait_autoneg and igc_set_fc_watermarks
up to avoid forward declaration.
It is not necessary to forward declare these static methods.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After hot plugging an 1Gbps Ethernet cable with 1Gbps link partner, the
MII_BMSR may report 10Mbps, renders the network rather slow.
The issue has much lower fail rate after commit 59653e6497d1 ("e1000e:
Make watchdog use delayed work"), which essentially introduces some
delay before running the watchdog task.
But there's still a chance that the hot plugging event and the queued
watchdog task gets run at the same time, then the original issue can be
observed once again.
So let's use mod_delayed_work() to add a deterministic 1 second delay
before running watchdog task, after an interrupt.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixed issue in VM which shows no link when hypervisor is
restored from low-power state. The driver is responsible for re-enabling
any features of the device that had been disabled during suspend calls,
such as IRQs and bus mastering.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is no caller of function iavf_debug_d() in tree since
commit 75051ce4c5d8 ("iavf: Fix up debug print macro"),
so it can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Unlike normal TCP code TLS has to touch the cache lines
it copies into to fill header info. On memory-heavy workloads
having non temporal stores and normal accesses targeting
the same cache line leads to significant overhead.
Measured 3% overhead running 3600 round robin connections
with additional memory heavy workload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For TLS device offload the tag/message authentication code are
filled in by the device. The kernel merely reserves space for
them. Because device overwrites it, the contents of the tag make
do no matter. Current code tries to save space by reusing the
header as the tag. This, however, leads to an additional frag
being created and defeats buffer coalescing (which trickles
all the way down to the drivers).
Remove this optimization, and try to allocate the space for
the tag in the usual way, leave the memory uninitialized.
If memory allocation fails rewind the record pointer so that
we use the already copied user data as tag.
Note that the optimization was actually buggy, as the tag
for TLS 1.2 is 16 bytes, but header is just 13, so the reuse
may had looked past the end of the page..
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All modifications to TLS record list happen under the socket
lock. Since records form an ordered queue readers are only
concerned about elements being removed, additions can happen
concurrently.
Use RCU primitives to ensure the correct access types
(READ_ONCE/WRITE_ONCE).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's generally more cache friendly to walk arrays in order,
especially those which are likely not in cache.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate the array spec_opcode on the stack but instead make it
static const. Makes the object code smaller by 48 bytes.
Before:
text data bss dec hex filename
6914 1040 128 8082 1f92 hns3/hns3vf/hclgevf_cmd.o
After:
text data bss dec hex filename
6866 1040 128 8034 1f62 hns3/hns3vf/hclgevf_cmd.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate the arrays on the stack but instead make them
static const. Makes the object code smaller by 281 bytes.
Before:
text data bss dec hex filename
87553 5672 0 93225 16c29 benet/be_cmds.o
After:
text data bss dec hex filename
87112 5832 0 92944 16b10 benet/be_cmds.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may have some SoCs that can't achieve XGMAC max speed. Limit it if
asked to.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test to validate that Split Header feature is working correctly.
It works by using the rececently introduced counter that increments each
time a packet with split header is received.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are already doing it by default in the TX path so we can also enable
Jumbo Frame support in the RX path independently of MTU value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to set the RX tail pointer so that RX engine starts working
again after finishing the Flow Control test.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checks for support of Source Address Insertion/Replacement before
running the test.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a re-post of previous patch wrote by David Miller[1].
Phil Karn reported[2] that on busy networks with lots of unresolved
multicast routing entries, the creation of new multicast group routes
can be extremely slow and unreliable.
The reason is we hard-coded multicast route entries with unresolved source
addresses(cache_resolve_queue_len) to 10. If some multicast route never
resolves and the unresolved source addresses increased, there will
be no ability to create new multicast route cache.
To resolve this issue, we need either add a sysctl entry to make the
cache_resolve_queue_len configurable, or just remove cache_resolve_queue_len
limit directly, as we already have the socket receive queue limits of mrouted
socket, pointed by David.
>From my side, I'd perfer to remove the cache_resolve_queue_len limit instead
of creating two more(IPv4 and IPv6 version) sysctl entry.
[1] https://lkml.org/lkml/2018/7/22/11
[2] https://lkml.org/lkml/2018/7/21/343
v3: instead of remove cache_resolve_queue_len totally, let's only remove
the hard code limit when allocate the unresolved cache, as Eric Dumazet
suggested, so we don't need to re-count it in other places.
v2: hold the mfc_unres_lock while walking the unresolved list in
queue_count(), as Nikolay Aleksandrov remind.
Reported-by: Phil Karn <karn@ka9q.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF NIC may go down then come up during host servicing events. This
causes the VF NIC offloading feature settings to roll back to the
defaults. This patch can synchronize features from synthetic NIC to
the VF NIC during ndo_set_features (ethtool -K),
and netvsc_register_vf when VF comes back after host events.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Mark Bloch <markb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a previous patch, the NETIF_F_SG was missing after the code changes.
That caused the SG feature to be "fixed". This patch includes it into
hw_features, so it is tunable again.
Fixes: 23312a3be999 ("netvsc: negotiate checksum and segmentation parameters")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_diag_get_aux_size() can be called with sockets in any state.
icsk_ulp_ops is only present for full sockets.
For SYN_RECV or TIME_WAIT ones we would access garbage.
Fixes: 61723b393292 ("tcp: ulp: add functions to dump ulp-specific information")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Luke Hsiao <lukehsiao@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need for fib_notifier_ops to be in struct net. It is used only by
fib_notifier as a private data. Use net_generic to introduce per-net
fib_notifier struct and move fib_notifier_ops there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable rx_process_result is being initialized with a value that
is never read and is being re-assigned immediately afterwards. The
assignment is redundant, so replace it with the return from function
lan743x_rx_process_packet.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only use the TROCR register on R-Car Gen3 as it is not present on other
SoCs.
Offsets used for the undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas it
remains unclear why this driver accesses these fields on R-Car Gen2 but
regardless of what the historical reasons are the current code is
considered incorrect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the use of the undocumented BOC bit of the CCC register.
Current documentation for EtherAVB (ravb) describes the offset of what the
driver uses as the BOC bit as reserved and that only a value of 0 should be
written. After some internal investigation with Renesas it remains unclear
why this driver accesses these fields but regardless of what the historical
reasons are the current code is considered incorrect.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the use of the undocumented counter registers
CDCR, LCCR, CERCR, CEECR.
Offsets used for undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas
it remains unclear why this driver accesses these fields but regardless of
what the historical reasons are the current code is considered incorrect.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The field name is FBP rather than FPB.
This field is unused and could equally be removed from the driver entirely.
But there seems no harm in leaving as documentation of the presence of the
field.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: 610247f46feb ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When using single_open(), single_release() should be used instead
of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Obviously, variable 'copied' is initialized to zero. But it is not used.
hence just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a trivial debugfs entry for triggering reset just like in case
of firmware crash. It works by writing 1 to it:
echo 1 > reset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In case of compiling driver without DEBUG expose a stub function to make
writing debug code much simpler (no extra conditions). This will allow
e.g. using debugfs_create_file() without any magic if or #ifdef.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
hidp_send_message was changed to return non-zero values on success,
which some other bits did not expect. This caused spurious errors to be
propagated through the stack, breaking some drivers, such as hid-sony
for the Dualshock 4 in Bluetooth mode.
As pointed out by Dan Carpenter, hid-microsoft directly relied on that
assumption as well.
Fixes: 48d9cc9d85dd ("Bluetooth: hidp: Let hidp_send_message return number of queued bytes")
Signed-off-by: Dan Elkouby <streetwalkermc@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
hclge_dbg_get_m7_info is used only in the hclge_debugfs.c,
so it should be declared with static.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the selftest and reset are performed at the same time, the loopback
setting may be still in the enable state after the reset. As a result,
packets cannot be sent out.
This patch fixes this issue by disabling loopback in hclge_mac_init.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unnecessary.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNS3 driver can only unregister client which included in hnae3_client_list.
This patch adds the client node validity judgment.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Sasha Neftin
Firo Yang
Mauro S. M. Rodrigues
Mitch Williams
Jacob Keller
Jeff Kirsher
Kai-Heng Feng
Radoslaw Tyl
YueHaibing
Jakub Kicinski
Colin Ian King
Jose Abreu
Hangbin Liu
Haiyang Zhang
Eric Dumazet
Jiri Pirko
zhong jiang
Simon Horman
Andy Shevchenko
Wei Yongjun
Rafał Miłecki
Dan Elkouby
Guojia Liao
Yufeng Mo
Peng Li