| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For debug, it's interesting to create a loopback stream for each link
and use debugfs to set a source and target PDI. The target PDI would
need to be an RX port and use the same register configurations as the
source PDI. This capability allows e.g. for the headphone playback
stream to be snooped on the headset capture stream, or alternatively
for the addition of a dedicated loopback stream, in addition of
regular capture for that link.
This patch only adds the debugfs part, the port/PDI handling will be
handled in the next patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Mockup devices don't take part in command/control operations and their
virtual ports shall not be programmed.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
All read and writes from/to SoundWire mockup devices will return
-ENODATA/Command_Ignored, this patch forces a Command_OK result to let
the bus perform the required configurations, e.g. for the Data Ports,
which will only have an effect on the Master side.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
SoundWire mockup devices don't take part in the command/control
protocol, so all commands will complete with -ENODATA or
Command_Ignored results. With a flag, we can suppress such errors in
the bus management and make it appear as if all read/writes succeed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This change is needed for support of mockup devices, which by
construction will not provide any answer to a bank switch, but it's
also legit for regular cases.
If for some reason a device loses sync and cannot handle a bank
switch, we should go ahead anyways. The devices can always resync
later.
The only case where the error flow should be used is when there is a
Command_Aborted composite answer from SoundWire devices.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The Cadence IP exposes a small number of self-clearing bits in
the MCP_CONTROL and MCP_CONFIG_UPDATE registers.
We currently do not check that those bits are indeed cleared,
e.g. during resume operations. That could lead to resuming peripheral
devices too early.
In addition, if we happen to read these registers, update one of the
fields and write the register back, we may be writing stale data that
might have been cleared in hardware. These sort of race conditions
could lead to e.g. doing a hw_reset twice or stopping a clock that
just restarted. There is no clear way of avoiding these potential race
conditions other than making sure that these registers fields are
cleared before any read-modify-write sequence. If we detect this sort
of errors, we only log them since there is no clear recovery
possible. The only way out is likely to restart the IP with a
suspend/resume cycle.
Note that the checks are performed before updating the registers, as
well as after the Intel 'sync go' sequence in multi-link mode. That
should cover both the start and end of suspend/resume hardware
configurations. The Multi-Master mode gates the configuration updates
until the 'sync go' signal is asserted, so we only check on init and
after the end of the 'sync go' sequence.
The duration of the usleep_range() was defined by the GSYNC frequency
used in multi-master mode. With a 4kHz frequency, any configuration
change might be deferred by up to 250us. Extending the range to
1000-1500us should guarantee that the configuration change is
completed without any significant impact on the overall resume
time.
Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714051349.13064-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The same quirk is used for LAPBC510 and LAPBC710 skews who use the
same audio design.
These devices have the same BIOS issues inherited from the Intel
reference, add the same _ADR remap previously used on HP devices.
BugLink: https://github.com/thesofproject/linux/issues/3049
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210719233248.557923-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Call to sdw_update_slave_status() needs to be added to sdw_clear_slave_
status() to ensure Slaves are informed of the new status via update_
status() callback.
This will enable codec drivers to reset their internal states and make
sure the register settings are properly restored on pm_runtime or
system resume
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210714033609.11963-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The ret is not used in the interrupt handler, it is just returned without
any condition or change.
We can return the IRQ_HANDLED directly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714015555.17685-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We've added quite a few filters to avoid throwing errors if a Device
does not respond to commands during the clock stop sequences, but we
missed one.
This will lead to an isolated message
[ 6115.294412] soundwire sdw-master-1: SDW_SCP_STAT bread failed:-61
The callers already filter this error code, so there's no point in
keeping it at the lower level.
Since this is a recoverable error, make this dev_err() conditional and
only log cases with Command Failed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714014209.17357-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Sparse throws the following type of warnings:
drivers/soundwire/dmi-quirks.c:25:17: error: constant
0x000010025D070100 is so big it is long
Let's add the 'ull' suffix to make this go away and find real issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714013027.17022-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for SoundWire mockup devices. The configurations assume the
same topology as the CML SoundWire devices and can be used to test the
SOF firmware on a development board (RVP, UpExtreme) without any
hardware connected.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the same idea as for CNL/UpExtreme and add mockup test
first. They will only be selected if the SSDT is modified to add such
mockup devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for two configurations with SoundWire mockup devices that
emulate the two CometLake configurations with one and two amps. This
patch helps test the SOF firmware on an UpExtreme board without any
hardware connected, e.g. by doing a loopback of the playback stream on
capture streams.
The mapping of the partIDs is as follows:
0xAAAA: generic full-duplex codec (not currently used)
0xAA55: headset codec (mock-up of RT711/RT5682) - full-duplex
0x55AA: amplifier (mock-up of RT1308/RT1316/Maxim 98373) - playback
with IV sense feedback
0x5555: mic codec (mock-up of RT715) - capture-only
The tables are added in a separate file to allow for mockup codecs to be
added on other platforms, but the mapping to specific topologies
remains platform-specific.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To test the host controller and bus management code, it is currently
required to have a physical SoundWire peripheral attached to the
bus. To help with pre-silicon or early hardware enablement, it would
be very useful to have a SoundWire 'mockup' device that is exposed in
platform firmware but does not drive any signal on the bus.
This is different to the existing ASoC 'dummy' codec uses for I2S/TDM,
the SoundWire spec makes it clear that a device that is not attached
to the bus is not permitted to interact with the bus, be it for
command/control or data.
This patch exposes a 'mockup' device, with a minimalist driver, with 4
partID values reserved by Intel for such test configurations. The
mockup device exposes one full-duplex DAI based on 2 ports (DP1 for
playback and DP8 for capture). The capture data port is just virtual,
such a mockup device is prevented by the SoundWire specification from
presenting any data generated by a Source port without being Attached.
All the callbacks exposed by the SoundWire Slave interface are
populated, even if they just return immediately. This is intentional
to describe what a minimal codec driver should do and implement and
help new codec vendors provide support for their devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
I know nothing about zone_device pages and !device_private pages; but if
try_to_migrate_one() will do nothing for them, then it's better that
try_to_migrate() filter them first, than trawl through all their vmas.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Link: https://lore.kernel.org/lkml/1241d356-8ec9-f47b-a5ec-9b2bf66d242@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the unlikely race case that page_mlock_one() finds VM_LOCKED has been
cleared by the time it got page table lock, page_vma_mapped_walk_done()
must be called before returning, either explicitly, or by a final call
to page_vma_mapped_walk() - otherwise the page table remains locked.
Fixes: cd62734ca60d ("mm/rmap: split try_to_munlock from try_to_unmap")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/lkml/20210711151446.GB4070@xsang-OptiPlex-9020/
Link: https://lore.kernel.org/lkml/f71f8523-cba7-3342-40a7-114abc5d1f51@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The kernel recovers in due course from missing Mlocked pages: but there
was no point in calling page_mlock() (formerly known as
try_to_munlock()) on a THP, because nothing got done even when it was
found to be mapped in another VM_LOCKED vma.
It's true that we need to be careful: Mlocked accounting of pte-mapped
THPs is too difficult (so consistently avoided); but Mlocked accounting
of only-pmd-mapped THPs is supposed to work, even when multiple mappings
are mlocked and munlocked or munmapped. Refine the tests.
There is already a VM_BUG_ON_PAGE(PageDoubleMap) in page_mlock(), so
page_mlock_one() does not even have to worry about that complication.
(I said the kernel recovers: but would page reclaim be likely to split
THP before rediscovering that it's VM_LOCKED? I've not followed that up)
Fixes: 9a73f61bdb8a ("thp, mlock: do not mlock PTE-mapped file huge pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/lkml/cfa154c-d595-406-eb7d-eb9df730f944@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Parallel developments in mm/rmap.c have left behind some out-of-date
comments: try_to_migrate_one() also accepts TTU_SYNC (already commented
in try_to_migrate() itself), and try_to_migrate() returns nothing at
all.
TTU_SPLIT_FREEZE has just been deleted, so reword the comment about it
in mm/huge_memory.c; and TTU_IGNORE_ACCESS was removed in 5.11, so
delete the "recently referenced" comment from try_to_unmap_one() (once
upon a time the comment was near the removed codeblock, but they drifted
apart).
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Link: https://lore.kernel.org/lkml/563ce5b2-7a44-5b4d-1dfd-59a0e65932a9@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit dbbee9d5cd83 ("mm/page_alloc: convert per-cpu list protection to
local_lock") folded in a workaround patch for pahole that was unable to
deal with zero-sized percpu structures.
A superior workaround is achieved with commit a0b8200d06ad ("kbuild:
skip per-CPU BTF generation for pahole v1.18-v1.21").
This patch reverts the dummy field and the pahole version check.
Fixes: dbbee9d5cd83 ("mm/page_alloc: convert per-cpu list protection to local_lock")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
arch/arm/mach-ixp4xx/include/mach/platform.h now gets included indirectly
and defines REG_OFFSET. Rename the register and bit definition to something
specific to the driver.
Fixes: 7fd70c65faac ("ARM: irqstat: Get rid of duplicated declaration")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210710211431.1393589-1-alexandre.belloni@bootlin.com
|
|
commit 03623b4b041c ("rtc: pcf2127: add tamper detection support")
added support for timestamp interrupts. However they are not being
handled in the irq handler. If a timestamp interrupt occurs it
results in kernel disabling the interrupt and displaying the call
trace:
[ 121.145580] irq 78: nobody cared (try booting with the "irqpoll" option)
...
[ 121.238087] [<00000000c4d69393>] irq_default_primary_handler threaded [<000000000a90d25b>] pcf2127_rtc_irq [rtc_pcf2127]
[ 121.248971] Disabling IRQ #78
Handle timestamp interrupts in pcf2127_rtc_irq(). Save time stamp
before clearing TSF1 and TSF2 flags so that it can't be overwritten.
Set a flag to mark if the timestamp is valid and only report to sysfs
if the flag is set. To mimic the hardware behavior, don’t save
another timestamp until the first one has been read by the userspace.
However, if the alarm irq is not configured, keep the old way of
handling timestamp interrupt in the timestamp0 sysfs calls.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210629150643.31551-1-ykaukab@suse.de
|
|
The offset variable is checked by at91_rtc_readalarm(), but this check
is unnecessary because the previous check knew that the value of this
variable was not 0.
This removes that unnecessary offset variable checks.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210708051340.341345-1-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
s5m_check_peding_alarm_interrupt() in s5m_rtc_read_alarm() gets the return
value, but doesn't use it.
This modifies using the s5m_check_peding_alarm_interrupt()"s return value
as the s5m_rtc_read_alarm()'s return value.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210708051304.341278-1-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-11-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-9-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-8-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
For C files, use the C99 format (//).
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-7-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
For C files, use the C99 format (//).
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-6-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-5-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-4-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-3-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-2-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
This reverts commit 65db04053efea3f3e412a7e0cc599962999c96b4.
Guenter reported that after 65db04053efe, the ppc:sam460ex qemu emulation
no longer boots from nvme:
nvme nvme0: Device not ready; aborting initialisation, CSTS=0x0
nvme nvme0: Removing after probe failure status: -19
Link: https://lore.kernel.org/r/20210709231529.GA3270116@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After updating the datasheet URL, the PCF85063A datasheet revision
has changed.
Adjust it accordingly.
Reported-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210624120953.2313378-1-festevam@gmail.com
|
|
Take maintainership of the binding as PAvel said he doesn't have the
hardware anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20210620224030.1115356-1-alexandre.belloni@bootlin.com
|
|
ASan reported a memory leak for items of the entlist returned from scandir().
In fact, scandir() returns a malloc'd array of malloc'd dirents.
This patch adds the missing (z)frees.
Fixes: da963834fe6975a1 ("perf test: Iterate over shell tests in alphabetical order")
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Fabian Hemmer <copy@copy.sh>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Remi Bernon <rbernon@codeweavers.com>
Link: http://lore.kernel.org/lkml/20210709163454.672082-1-rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add a test for the newly added perf_evlist__set_leader() function.
Committer testing:
$ cd tools/lib/perf/
$ sudo make tests
[sudo] password for acme:
running static:
- running tests/test-cpumap.c...OK
- running tests/test-threadmap.c...OK
- running tests/test-evlist.c...OK
- running tests/test-evsel.c...OK
running dynamic:
- running tests/test-cpumap.c...OK
- running tests/test-threadmap.c...OK
- running tests/test-evlist.c...OK
- running tests/test-evsel.c...OK
$
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Requested-by: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210706151704.73662-8-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
We shouldn't just panic, return a value that doesn't clash with what
perf_evsel__open() was already returning in case of error, i.e. errno
when sys_perf_event_open() fails.
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Link: http://lore.kernel.org/lkml/YOiOA5zOtVH9IBbE@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To 2.33
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The optional @ref parameter might contain an NULL node_name, so
prevent dereferencing it in cifs_compose_mount_options().
Addresses-Coverity: 1476408 ("Explicit null dereferenced")
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Add support to set group_fd in perf_evsel__open() and make it follow the
group setup.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Requested-by: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210706151704.73662-7-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Support for faster packet signing (using GMAC instead of CMAC) can
now be negotiated to some newer servers, including Windows.
See MS-SMB2 section 2.2.3.17.
This patch adds support for sending the new negotiate context
with the first of three supported signing algorithms (AES-CMAC)
and decoding the response. A followon patch will add support
for sending the other two (including AES-GMAC, which is fastest)
and changing the signing algorithm used based on what was
negotiated.
To allow the client to request GMAC signing set module parameter
"enable_negotiate_signing" to 1.
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Some different PMU types may have the same substring. For example, on
Icelake server we have PMU types "uncore_imc" and
"uncore_imc_free_running". Both PMU types have the substring
"uncore_imc". But the parser wrongly thinks they are the same PMU type.
We enable an imc event,
perf stat -e uncore_imc/event=0xe3/ -a -- sleep 1
Perf actually expands the event to:
uncore_imc_0/event=0xe3/
uncore_imc_1/event=0xe3/
uncore_imc_2/event=0xe3/
uncore_imc_3/event=0xe3/
uncore_imc_4/event=0xe3/
uncore_imc_5/event=0xe3/
uncore_imc_6/event=0xe3/
uncore_imc_7/event=0xe3/
uncore_imc_free_running_0/event=0xe3/
uncore_imc_free_running_1/event=0xe3/
uncore_imc_free_running_3/event=0xe3/
uncore_imc_free_running_4/event=0xe3/
That's because the "uncore_imc_free_running" matches the
pattern "uncore_imc*".
Now we check that the last characters of PMU name is '_<digit>'.
For example, for pattern "uncore_imc*", "uncore_imc_0" is parsed ok, but
"uncore_imc_free_running_0" fails.
Fixes: b2b9d3a3f0211c5d ("perf pmu: Support wildcards on pmu name in dynamic pmu events")
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Agustin Vega-Frias <agustinv@codeaurora.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210701064253.1175-1-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Some symbols may not be resolved if a user only monitors one type of
PMU.
$ sudo perf record -e cpu_atom/branch-instructions/ ./big_small_workload
$ sudo perf report –stdio
# Overhead Command Shared Object Symbol
# ........ ......... ................. .....................
#
28.02% perf-exec [unknown] [.] 0x0000000000401cf6
11.32% perf-exec [unknown] [.] 0x0000000000401d04
10.90% perf-exec [unknown] [.] 0x0000000000401d11
10.61% perf-exec [unknown] [.] 0x0000000000401cfc
To parse symbols the metadata records, e.g., PERF_RECORD_COMM, which are
generated by the kernel, are required.
To decide whether to generate the metadata records, the kernel relies on
the event_filter_match() to filter the unrelated events.
On a hybrid system, event_filter_match() further checks the CPU mask of
the current enabled PMU. If an event is collected on the CPU which
doesn't have an enabled PMU, it's treated as an unrelated event.
The "big_small_workload" is created in a big core, but runs on a small
core. The metadata records are filtered, because the user only monitors
the PMU of the small core. The big core PMU is not enabled.
For a hybrid system, a dummy event is required to generate the complete
side-band events.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/1625760212-18441-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The Topdown Microarchitecture Analysis (TMA) Method is a structured
analysis methodology to identify critical performance bottlenecks in
out-of-order processors.
The Topdown metrics L1 event was added as default in 42641d6f4d15e6db
("perf stat: Add Topdown metrics events as default events")
From the Sapphire Rapids server and later platforms, the same dedicated
"metrics" register is extended to support both L1 and L2 events.
Add both L1 and L2 Topdown metrics events as default to enrich the
default measuring information if the new measurement register is
available.
On legacy systems there is no change to avoid extra multiplexing.
The topdown_level indicates the max metrics level for the top-down
statistics. Set it to 2 to display all L1 and L2 Topdown metrics events.
With the patch:
$ perf stat sleep 1
Performance counter stats for 'sleep 1':
0.59 msec task-clock # 0.001 CPUs utilized
1 context-switches # 1.687 K/sec
0 cpu-migrations # 0.000 /sec
76 page-faults # 128.198 K/sec
1,405,318 cycles # 2.371 GHz
1,471,136 instructions # 1.05 insn per cycle
310,132 branches # 523.136 M/sec
10,435 branch-misses # 3.36% of all branches
8,431,908 slots # 14.223 G/sec
1,554,116 topdown-retiring # 18.4% retiring
1,289,585 topdown-bad-spec # 15.2% bad speculation
2,810,636 topdown-fe-bound # 33.2% frontend bound
2,810,636 topdown-be-bound # 33.2% backend bound
231,464 topdown-heavy-ops # 2.7% heavy operations # 15.6% light operations
1,223,453 topdown-br-mispredict # 14.5% branch mispredict # 0.8% machine clears
1,884,779 topdown-fetch-lat # 22.3% fetch latency # 10.9% fetch bandwidth
1,454,917 topdown-mem-bound # 17.2% memory bound # 16.0% Core bound
1.001179699 seconds time elapsed
0.000000000 seconds user
0.001238000 seconds sys
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/1625760169-18396-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Move the implementation of evlist__set_leader() to a new libperf
perf_evlist__set_leader() function with the same functionality make it a
libperf exported API.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Requested-by: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210706151704.73662-6-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Move evsel::nr_groups to perf_evsel::nr_groups, so we can move the group
interface to libperf.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Requested-by: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210706151704.73662-5-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Move evsel::leader to perf_evsel::leader, so we can move the group
interface to libperf.
Also add several evsel helpers to ease up the transition:
struct evsel *evsel__leader(struct evsel *evsel);
- get leader evsel
bool evsel__has_leader(struct evsel *evsel, struct evsel *leader);
- true if evsel has leader as leader
bool evsel__is_leader(struct evsel *evsel);
- true if evsel is itw own leader
void evsel__set_leader(struct evsel *evsel, struct evsel *leader);
- set leader for evsel
Committer notes:
Fix this when building with 'make BUILD_BPF_SKEL=1'
tools/perf/util/bpf_counter.c
- if (evsel->leader->core.nr_members > 1) {
+ if (evsel->core.leader->nr_members > 1) {
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Requested-by: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210706151704.73662-4-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
Pierre-Louis Bossart
Bard Liao
Peter Ujfalusi
Linus Torvalds
Hugh Dickins
Mel Gorman
Alexandre Belloni
Mian Yousaf Kaukab
Nobuhiro Iwamatsu
Bjorn Helgaas
Fabio Estevam
Riccardo Mancini
Jiri Olsa
Arnaldo Carvalho de Melo
Steve French
Paulo Alcantara
Jin Yao
Kan Liang