| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
____napi_schedule() needs to be invoked with disabled interrupts due to
__raise_softirq_irqoff (in order not to corrupt the per-CPU list).
____napi_schedule() needs also to be invoked from an interrupt context
so that the raised-softirq is processed while the interrupt context is
left.
Add lockdep asserts for both conditions.
While this is the second time the irq/softirq check is needed, provide a
generic lockdep_assert_softirq_will_run() which is used by both caller.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add net device refcount tracker to macvlan.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the reference operation to lowerdev of macvlan to avoid
the potential UAF problem under the following known scenario:
Someone module puts the NETDEV_UNREGISTER event handler to a
work, and lowerdev is accessed in the work handler. But when
the work is excuted, lowerdev has been destroyed because upper
macvlan did not get reference to lowerdev correctly.
That likes as the scenario occurred by
commit 563bcbae3ba2 ("net: vlan: fix a UAF in vlan_dev_real_dev()").
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch increases the number of RX-FIFOs to 3 and the max TX-FIFO
depth to 16. This leads to the following default ring configuration.
CAN-2.0 mode:
| FIFO setup: TEF: 0x400: 8*12 bytes = 96 bytes
| FIFO setup: RX-0: FIFO 1/0x460: 32*20 bytes = 640 bytes
| FIFO setup: RX-1: FIFO 2/0x6e0: 32*20 bytes = 640 bytes
| FIFO setup: RX-2: FIFO 3/0x960: 16*20 bytes = 320 bytes
| FIFO setup: TX: FIFO 4/0xaa0: 8*16 bytes = 128 bytes
| FIFO setup: free: 224 bytes
CAN-FD mode:
| FIFO setup: TEF: 0x400: 4*12 bytes = 48 bytes
| FIFO setup: RX-0: FIFO 1/0x430: 16*76 bytes = 1216 bytes
| FIFO setup: RX-1: FIFO 2/0x8f0: 4*76 bytes = 304 bytes
| FIFO setup: TX: FIFO 3/0xa20: 4*72 bytes = 288 bytes
| FIFO setup: free: 192 bytes
With the previously added ethtool ring configuration support the RAM
on the chip can now be runtime configured between RX and TX buffers.
Link: https://lore.kernel.org/20220313083640.501791-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support ethtool based configuration for the TX IRQ
coalescing added in the previous patch.
Link: https://lore.kernel.org/20220313083640.501791-12-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds TX IRQ coalescing support to the driver.
The implemented algorithm is similar to the RX IRQ coalescing support
added in the previous patch.
Link: https://lore.kernel.org/20220313083640.501791-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support ethtool based configuration for the RX IRQ
coalescing added in the previous patch.
Link: https://lore.kernel.org/20220313083640.501791-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds RX IRQ coalescing support to the driver.
The mcp251xfd chip doesn't support proper hardware based coalescing,
so this patch tries to implemented it in software. The RX-FIFO offers
a "FIFO not empty" interrupt, which is used if no coalescing is
active.
With activated RX IRQ coalescing the "FIFO not empty" interrupt is
disabled in the RX IRQ handler and the "FIFO half full" or "FIFO full
interrupt" (depending on RX max coalesced frames IRQ) is used instead.
To avoid RX CAN frame starvation a hrtimer is setup with RX coalesce
usecs IRQ,on timer expiration the "FIFO not empty" is enabled again.
Support for ethtool configuration is added in the next patch.
Link: https://lore.kernel.org/20220313083640.501791-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds runtime configurable RX and TX ring parameters via
ethtool to the driver.
Link: https://lore.kernel.org/20220313083640.501791-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
So far the configuration of the hardware FIFOs is hard coded and
depend only on the selected CAN mode (CAN-2.0 or CAN-FD).
This patch updates the macros describing the ring, FIFO and RAM layout
to prepare for the next patches that add support for runtime
configurable ring parameters via ethtool.
Link: https://lore.kernel.org/20220313083640.501791-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch prepares the driver for runtime configurable RX and TX ring
parameters. The actual runtime config support will be added in the
next patch.
Link: https://lore.kernel.org/20220313083640.501791-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds basic ethtool support (to query the current and
maximum ring parameters) to the driver.
Link: https://lore.kernel.org/20220313083640.501791-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support for coalescing to the RAM layout calculation.
Link: https://lore.kernel.org/20220313083640.501791-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds a helper function to calculate the ring configuration
of the controller based on various constraints, like available RAM,
size of RX and TX objects, CAN-mode, number of FIFOs and FIFO depth.
Link: https://lore.kernel.org/20220313083640.501791-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of an erroneous ring configuration more RAM than available
might be used. Change the printf modifier to a signed int to properly
print this erroneous value.
Fixes: 83daa863f16b ("can: mcp251xfd: ring: update FIFO setup debug info")
Link: https://lore.kernel.org/20220313083640.501791-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the freeing of the "oskb", by using kfree_skb()
instead of kfree().
Fixes: 1574481bb3de ("vxcan: remove sk reference in peer skb")
Link: https://lore.kernel.org/all/20220311123741.382618-1-mkl@pengutronix.de
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case external PHY is used, we need to take care of embedded PHY.
Since there are no methods to disable this PHY from the MAC side and
keeping RMII reference clock, we need to suspend it.
This patch will reduce electrical noise (PHY is continuing to send FLPs)
and power consumption by 0,22W.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In most cases we use own mdio bus, there is no need to create and store
string for the PHY address.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already read chipid on probe. There is no need to read it on reset.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only difference is the reset code, so remove not needed duplicates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable binding the nfp driver to NFP3800 and NFP3803 devices.
The PCIE_SRAM offset is different for the NFP3800 device, which also
only supports a single explicit group.
Changes to Dirk's work:
* 48-bit dma addressing is not ready yet. Keep 40-bit dma addressing
for NFP3800.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NFP3800 has slightly different queue controller range bounds.
Use the static chip data instead of defines. This commit
still assumes unchanged descriptor format. Later datapath
changes will allow adjusting for descriptor accounting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The queue controller (QCP) is accessed based on a device specific
offset. The NFP3800 device also supports more queues.
Furthermore, the NFP3800 VFs also access the QCP differently to how the
NFP6000 VFs accesses it, though still indirectly. Fortunately, we can
remove the offset all together for both VF types. This is safe for
NFP6000 VFs since the offset was effectively a wrap around and only used
for convenience to have it set the same as the NFP6000 PF.
Use nfp_dev_info to store queue controller parameters.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for new chips instead of defines use dev_info constants
to store DMA mask length.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NFP3800 uses a different PCIe configuration to CPP expansion BAR offsets.
We don't need to differentiate between the NFP4000, NFP5000 and NFP6000
since they all use the same offsets.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for supporting new chip add a driver data structure
which will hold per-chip-version information such as register
offsets.
Plumb it through to the relevant functions (nfpcore and nfp_net).
For now only a very simple member holding chip names is added,
following commits will add more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make sure the device ID tables are in ascending order.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The model number for NFP3800 and newer devices can be completely
derived from PluDevice register without subtracting 0x10.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PCI_DEVICE_ID_NETRONOME_NFP6000_VF is available for use and
should be used instead of the PCI_DEVICE_NFP6000VF. Meanwhile,
PCI_DEVICE_NFP6000VF PCI ID is removed for not being used.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Multiple writes cause intermediate pointer values that do not
end on complete TX descriptors.
The QCP peripheral on the NFP provides a number of access
modes. In some access modes, the maximum amount to add must
be restricted to a 6bit value. The particular access mode
used by _nfp_qcp_ptr_add() has no such restrictions, so the
"< NFP_QCP_MAX_ADD" test is unnecessary.
Note that trying to add more that the configured ring size
in a single add will cause a QCP overflow, caught and handled
by the QCP peripheral.
Signed-off-by: Christo du Toit <christo.du.toit@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NFP driver ABI contains a bit for ring prioritization which
was never implemented in the initially envisioned form.
Remove it, and open up the possibility of reclaiming for other uses.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warning:
./drivers/net/ethernet/8390/mcf8390.c:414:2-9: line 414 is redundant
because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220311001756.12234-1-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdev_name_node_alt_create() and netdev_name_node_alt_destroy()
are only called by rtnetlink, so no need for exports.
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220310223952.558779-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In function netvsc_process_raw_pkt for VM_PKT_DATA_USING_XFER_PAGES
case there is already a 'return' statement which results 'break'
as dead code
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1646933534-29493-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both functions are only used by core networking code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220310143229.895319-1-hch@lst.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In review for commit 8ee7ec4890e2b ("net: ipa: embed interconnect
array in the power structure"), Jakub Kicinski suggested that a
follow-up patch use struct_size() when computing the size of the
IPA power structure, which ends with a flexible array member.
Do that.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220311162423.872645-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for creating filters for GTP-U and GTP-C in switchdev mode. Add
support for parsing GTP-specific options (QFI and PDU type) and TEID.
By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR
Note: GTP-U with outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Checking only protocol ids while searching for correct FVs can lead to a
situation, when incorrect FV will be added to the list. Incorrect means
that FV has correct protocol id but incorrect offset.
Call ice_get_sw_fv_list with ice_prot_lkup_ext struct which contains all
protocol ids with offsets.
With this modification allocating and collecting protocol ids list is
not longer needed.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a function that checks if a net device type is GTP.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Options are as follows: PDU_TYPE:QFI and they refernce to
the fields from the PDU Session Protocol. PDU Session data
is conveyed in GTP-U Extension Header.
GTP-U Extension Header is described in 3GPP TS 29.281.
PDU Session Protocol is described in 3GPP TS 38.415.
PDU_TYPE - indicates the type of the PDU Session Information (4 bits)
QFI - QoS Flow Identifier (6 bits)
# ip link add gtp_dev type gtp role sgsn
# tc qdisc add dev gtp_dev ingress
# tc filter add dev gtp_dev protocol ip parent ffff: \
flower \
enc_key_id 11 \
gtp_opts 1:8/ff:ff \
action mirred egress redirect dev eth0
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Adding GTP device through ip link creates the situation where
GTP instance is not able to send GTP echo requests.
Echo requests are used to check if GTP peer is still alive.
With this patch, gtp_genl_ops are extended by new cmd (GTP_CMD_ECHOREQ)
which allows to send echo request in the given version of GTP
protocol (v0 or v1), from the given ms address to he given
peer. TID is not inclued because in all path management
messages it should be equal to 0.
When GTP echo response is detected, multicast message is
send to everyone in the gtp_genl_family. Message contains
GTP version, ms address and peer address.
Suggested-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Adding GTP device through ip link creates the situation where
there is no userspace daemon which would handle GTP messages
(Echo Request for example). GTP-U instance which would not respond
to echo requests would violate GTP specification.
When GTP packet arrives with GTP_ECHO_REQ message type,
GTP_ECHO_RSP is send to the sender. GTP_ECHO_RSP message
should contain information element with GTPIE_RECOVERY tag and
restart counter value. For GTPv1 restart counter is not used
and should be equal to 0, for GTPv0 restart counter contains
information provided from userspace(IFLA_GTP_RESTART_COUNT).
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Suggested-by: Harald Welte <laforge@gnumonks.org>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Tested-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, when the user wants to create GTP device, he has to
provide file handles to the sockets created in userspace (IFLA_GTP_FD0,
IFLA_GTP_FD1). This behaviour is not ideal, considering the option of
adding support for GTP device creation through ip link. Ip link
application is not a good place to create such sockets.
This patch allows to create GTP device without providing
IFLA_GTP_FD0 and IFLA_GTP_FD1 arguments. If the user sets
IFLA_GTP_CREATE_SOCKETS attribute, then GTP module takes care
of creating UDP sockets by itself. Sockets are created with the
commonly known UDP ports used for GTP protocol (GTP0_PORT and
GTP1U_PORT). In this case we don't have to provide encap_destroy
because no extra deinitialization is needed, everything is covered
by udp_tunnel_sock_release.
Note: GTP instance created with only this change applied, does
not handle GTP Echo Requests. This is implemented in the following
patch.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add sysfs nodes for the frequency generator and signal counters.
Update SMA selector lists for these, and also add the new
'None', 'VCC' 'GND' selectors.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The timecard now has 4 general purpose timestampers.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Input signals can be steered to any of the frequency counters.
The counter measures the frequency over a number of seconds:
echo 0 > freq1/seconds = turns off measurement
echo 1 > freq1/seconds = sets period & turns on measurment.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The signal generators can be programmed either via the sysfs
file or through a PTP_CLK_REQ_PEROUT ioctl request.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer firmware provides 4 programmable signal generators, add
support for those here. The signal generators provide the
ability to set the period, duty cycle, phase offset, and polarity,
with new values defaulting to prior values.
The period and phase offset are specified in nanoseconds.
E.g: period [duty [phase [polarity]]]
echo 500000000 > signal # 1/2 second period
echo 1000000 40 100 > signal # 1ms period, 40% on, offset 100ns
echo 0 > signal # turn off generator
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the ability to group sysfs nodes behind a firmware feature
check. This way non-present sysfs attributes are omitted on
older firmware, which does not have newer features.
This will be used in the upcoming patches which adds more
features to the timecard.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Sebastian Andrzej Siewior
Ziyang Xuan
Marc Kleine-Budde
Oleksij Rempel
Eric Dumazet
Dirk van der Merwe
Jakub Kicinski
Christo du Toit
Yang Li
Jakub Kicinski
Saurabh Sengar
Christoph Hellwig
Alex Elder
Marcin Szycik
Michal Swiatkowski
Wojciech Drewek
Jonathan Lemon