aboutsummaryrefslogtreecommitdiffstats
path: root/tools/perf/scripts/python/export-to-sqlite.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2021-10-25ipv4: guard IP_MINTTL with a static keyEric Dumazet3-8/+20
RFC 5082 IP_MINTTL option is rarely used on hosts. Add a static key to remove from TCP fast path useless code, and potential cache line miss to fetch inet_sk(sk)->min_ttl Note that once ip4_min_ttl static key has been enabled, it stays enabled until next boot. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25ipv4: annotate data races arount inet->min_ttlEric Dumazet2-3/+9
No report yet from KCSAN, yet worth documenting the races. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25ipv6: guard IPV6_MINHOPCOUNT with a static keyEric Dumazet3-8/+20
RFC 5082 IPV6_MINHOPCOUNT is rarely used on hosts. Add a static key to remove from TCP fast path useless code, and potential cache line miss to fetch tcp_inet6_sk(sk)->min_hopcount Note that once ip6_min_hopcount static key has been enabled, it stays enabled until next boot. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25ipv6: annotate data races around np->min_hopcountEric Dumazet2-3/+8
No report yet from KCSAN, yet worth documenting the races. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25net: annotate accesses to sk->sk_rx_queue_mappingEric Dumazet1-3/+7
sk->sk_rx_queue_mapping can be modified locklessly, add a couple of READ_ONCE()/WRITE_ONCE() to document this fact. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25net: avoid dirtying sk->sk_rx_queue_mappingEric Dumazet1-4/+2
sk_rx_queue_mapping is located in a cache line that should be kept read mostly. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25net: avoid dirtying sk->sk_napi_idEric Dumazet1-1/+2
sk_napi_id is located in a cache line that can be kept read mostly. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25ipv6: move inet6_sk(sk)->rx_dst_cookie to sk->sk_rx_dst_cookieEric Dumazet4-6/+7
Increase cache locality by moving rx_dst_coookie next to sk->sk_rx_dst This removes one or two cache line misses in IPv6 early demux (TCP/UDP) Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25tcp: move inet->rx_dst_ifindex to sk->sk_rx_dst_ifindexEric Dumazet4-8/+10
Increase cache locality by moving rx_dst_ifindex next to sk->sk_rx_dst This is part of an effort to reduce cache line misses in TCP fast path. This removes one cache line miss in early demux. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25ax88796c: fix fetching error stats from percpu containersAlexander Lobakin1-4/+4
rx_dropped, tx_dropped, rx_frame_errors and rx_crc_errors are being wrongly fetched from the target container rather than source percpu ones. No idea if that goes from the vendor driver or was brainoed during the refactoring, but fix it either way. Fixes: a97c69ba4f30e ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver") Signed-off-by: Alexander Lobakin <alobakin@pm.me> Acked-by: Łukasz Stelmach <l.stelmach@samsung.com> Link: https://lore.kernel.org/r/20211023121148.113466-1-alobakin@pm.me Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25bluetooth: use dev_addr_set()Jakub Kicinski1-1/+3
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it go through appropriate helpers. Reviewed-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25bluetooth: use eth_hw_addr_set()Jakub Kicinski1-1/+1
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it go through appropriate helpers. Convert bluetooth from memcpy(... ETH_ADDR) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, ETH_ALEN) + eth_hw_addr_set(dev, np) Reviewed-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25fddi: defza: add missing pointer type castJakub Kicinski1-1/+1
hw_addr is a uint AKA unsigned int. dev_addr_set() takes a u8 *. drivers/net/fddi/defza.c:1383:27: error: passing argument 2 of 'dev_addr_set' from incompatible pointer type [-Werror=incompatible-pointer-types] Reported-by: kernel test robot <lkp@intel.com> Fixes: 1e9258c389ee ("fddi: defxx,defza: use dev_addr_set()") Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/20211025160000.2803818-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25net/tls: getsockopt supports complete algorithm listTianjia Zhang1-0/+42
AES_CCM_128 and CHACHA20_POLY1305 are already supported by tls, similar to setsockopt, getsockopt also needs to support these two algorithms. Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net/tls: tls_crypto_context add supported algorithms contextTianjia Zhang1-0/+2
tls already supports the SM4 GCM/CCM algorithms. It is also necessary to add support for these two algorithms in tls_crypto_context to avoid potential issues caused by forced type conversion. Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25mlxsw: spectrum: Use 'bitmap_zalloc()' when applicableChristophe JAILLET4-27/+16
Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid some open-coded arithmetic in allocator arguments. Also change the corresponding 'kfree()' into 'bitmap_free()' to keep consistency. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25usbb: catc: use correct API for MAC addressesOliver Neukum1-5/+17
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. In the case of catc we need a new temporary buffer to conform to the rules for DMA coherency. That in turn necessitates a reworking of error handling in probe(). Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25gve: Add a jumbo-frame device option.Shailend Chand2-4/+68
A widely deployed driver has a bug that will cause the driver not to load when a max_mtu > 2048 is present in the device descriptor. To avoid this bug while still enabling jumbo frames, we present a lower max_mtu in the device descriptor and pass the actual max_mtu in a separate device option. The driver supports 2 different queue formats. To enable features on one queue format, but not the other, a supported_features mask was added to the device options in the device descriptor. Signed-off-by: Shailend Chand <shailend@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25gve: Implement packet continuation for RX.David Awogbemila9-126/+292
This enables the driver to receive RX packets spread across multiple buffers: For a given multi-fragment packet the "packet continuation" bit is set on all descriptors except the last one. These descriptors' payloads are combined into a single SKB before the SKB is handed to the networking stack. This change adds a "packet buffer size" notion for RX queues. The CreateRxQueue AdminQueue command sent to the device now includes the packet_buffer_size. We opt for a packet_buffer_size of PAGE_SIZE / 2 to give the driver the opportunity to flip pages where we can instead of copying. Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Reviewed-by: Catherine Sullivan <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25gve: Add RX context.David Awogbemila2-37/+44
This refactor moves the skb_head and skb_tail fields into a new gve_rx_ctx struct. This new struct will contain information about the current packet being processed. This is in preparation for multi-descriptor RX packets. Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Reviewed-by: Catherine Sullivan <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25selftests: mlxsw: Reduce test run timeIdo Schimmel2-18/+20
Instead of iterating over all the available trap policers, only perform the tests with three policers: The first, the last and the one in the middle of the range. On a Spectrum-3 system, this reduces the run time from almost an hour to a few minutes. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25selftests: mlxsw: Use permanent neighbours instead of reachable onesIdo Schimmel1-11/+11
The nexthop objects tests configure dummy reachable neighbours so that the nexthops will have a MAC address and be programmed to the device. Since these are dummy reachable neighbours, they can be transitioned by the kernel to a failed state if they are around for too long. This can happen, for example, if the "TIMEOUT" variable is configured with a too high value. Make the tests more robust by configuring the neighbours as permanent, so that the tests do not depend on the configured timeout value. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25selftests: mlxsw: Add helpers for skipping selftestsPetr Machata8-24/+81
A number of mlxsw-specific selftests currently detect whether they are run on a compatible machine, and bail out silently when not. These tests are however done in a somewhat impenetrable manner by directly comparing PCI IDs against a blacklist or a whitelist, and bailing out silently if the machine is not compatible. Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying the supported machines in a human-readable manner. If the current machine is incompatible, the helper emits a SKIP message and returns an error code, based on which the caller can gracefully bail out in a suitable way. This allows a more readable conditions such as: mlxsw_only_on_spectrum 2+ || return Convert all existing open-coded guards to the new helper. Also add two new guards to do_mark_test() and do_drop_test(), which are supported only on Spectrum-2+, but the corresponding check was not there. Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add qca8081 cdt featureLuo Jie1-3/+191
To perform CDT of qca8081 phy: 1. disable hibernation. 2. force phy working in MDI mode. 3. force phy working in 1000BASE-T mode. 4. configure the related thresholds. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: adjust qca8081 master/slave seed value if link downLuo Jie1-0/+16
1. The master/slave seed needs to be updated when the link can't be created. 2. The case where two qca8081 PHYs are connected each other and master/slave seed is generated as the same value also needs to be considered, so adding this code change into read_status instead of link_change_notify. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add qca8081 soft_reset and enable master/slave seedLuo Jie1-0/+48
qca8081 phy is a single port phy, configure phy the lower seed value to make it linked as slave mode easier. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add qca8081 config_initLuo Jie1-0/+107
Add the qca8081 phy driver config_init function, which includes: 1. Enable fast restrain. 2. Add 802.3az configurations. 3. Initialize ADC threshold as 100mv. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add genphy_c45_fast_retrainLuo Jie2-0/+35
Add generic fast retrain auto-negotiation function for C45 PHYs. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add constants for fast retrain related registerLuo Jie1-0/+9
Add the constants for 2.5G fast retrain capability in 10G AN control register, fast retrain status and control register and THP bypass register into mdio.h. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add qca8081 config_anegLuo Jie1-1/+25
Reuse at803x phy driver config_aneg excepting adding 2500M auto-negotiation. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add qca8081 get_featuresLuo Jie1-0/+10
Reuse the at803x phy driver get_features excepting adding 2500M capability. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add qca8081 read_statusLuo Jie1-22/+73
1. Separate the function at803x_read_specific_status from the at803x_read_status, since it can be reused by the read_status of qca8081 phy driver excepting adding the 2500M speed. 2. Add the qca8081 read_status function qca808x_read_status. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: add qca8081 ethernet phy driverLuo Jie1-1/+16
qca8081 is a single port ethernet phy chip that supports 10/100/1000/2500 Mbps mode. Add the basic phy driver features, and reuse the at803x phy driver functions. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: at803x: use GENMASK() for speed statusLuo Jie1-5/+5
Use GENMASK() for the current speed value. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: at803x: improve the WOL featureLuo Jie1-7/+38
The wol feature is controlled by the MMD3.8012 bit5, need to set this bit when the wol function is enabled. The reg18 bit0 is for enabling WOL interrupt, when wol occurs, the wol interrupt status reg19 bit0 is set to 1. Call phy_trigger_machine if there are any other interrupt pending in the function set_wol. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: at803x: use phy_modify()Luo Jie1-6/+2
Convert at803x_set_wol to use phy_modify. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: phy: at803x: replace AT803X_DEVICE_ADDR with MDIO_MMD_PCSLuo Jie1-3/+3
Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h. Signed-off-by: Luo Jie <luoj@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: add error recovery module and type for himacJiaran Zhang2-0/+12
This patch adds himac error recovery module, link_error type and ptp_error type for himac. Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: add new ras error type for roceWeihang Li2-1/+5
This patch adds one ras error of bus related for roce, this error including RRESP/BRESP and read poison error. Signed-off-by: Weihang Li <liweihang@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: add update ethtool advertised link modes for FIBRE port when autoneg offGuangbin Huang1-1/+77
Currently, the ethtool advertised link modes of FIBRE port is cleared to zero when autoneg is off, so user can not get the advertised link modes info directly from "ethtool <dev>" command. In order to ameliorate this situation, update data of speeds, fec and pause of advertised link modes when autoneg is off. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: modify functions of converting speed ability to ethtool link modeGuangbin Huang1-33/+37
The functions of converting speed ability to ethtool link mode just support setting mac->supported currently, to reuse these functions to set ethtool link mode for others(i.e. advertising), delete the argument mac and add argument link_mode. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: add support pause/pfc durations for mac statisticsGuangbin Huang4-92/+182
The mac statistics add pause/pfc durations in device version V3, we can get total active cycle of pause/pfc from these durations. As driver gets register number from firmware to calculate desc number to query mac statistics, it needs to set mac statistics extended enable bit in firmware command 0x701A to tell firmware that driver supports extended mac statistics, otherwise firmware only returns register number of version V1. As pause/pfc durations are not supported by hardware of old version, they should not been shown in command "ethtool -S ethX" in this case, so add checking max register number of each mac statistic in their version. If the max register number of one mac statistic is greater than register number got from firmware, it means hardware does not support this mac statistic, so ignore this statistic when get string and data of mac statistic. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: device specifications add number of mac statisticsGuangbin Huang3-11/+26
Currently, driver queries number of mac statistics before querying mac statistics. As the number of mac statistics is a fixed value in firmware, it is redundant to query this number everytime before querying mac statistics, it can just be queried once in initialization process and saved in device specifications. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: modify mac statistics update process for compatibilityGuangbin Huang2-47/+48
After querying mac statistics from firmware, driver copies data from descriptors to struct mac_stats of hdev, and the number of copied data is just according to the register number queried from firmware. There is a problem that if the register number queried from firmware is larger than data number of struct mac_stats, it will cause a copy overflow. So if the firmware adds more mac statistics in later version, it is not compatible with driver of old version. To fix this problem, the number of copied data needs to be used the minimum value between the register number queried from firmware and data number of struct mac_stats. The first descriptor has three data and there is one reserved, to optimize the copy process, add this reserverd data to struct mac_stats. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25net: hns3: add debugfs support for interrupt coalesceHuazhong Tan3-1/+122
Since user may need to check the current configuration of the interrupt coalesce, so add debugfs support for query this info. Create a single file "coalesce_info" for it, and query it by "cat coalesce_info", return the result to userspace. For device whose version is above V3(include V3), the GL's register contains usecs and 1us unit configuration. When get the usecs configuration from this register, it will include the confusing unit configuration, so add a GL mask to get the correct value, and add a QL mask for the frames configuration as well. The display style is below: $ cat coalesce_info tx interrupt coalesce info: VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT... 0 IN_PROG 4 EQE ON_TOP 0... 1 START 3 EQE LEFT 1... rx interrupt coalesce info: VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT... 0 IN_PROG 3 EQE LEFT 1... 1 IN_PROG 0 EQE ON_TOP 0... Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25s390/qeth: update kerneldoc for qeth_add_hw_header()Julian Wiedmann1-0/+2
qeth_add_hw_header() is missing documentation for some of its parameters, fix that up. Reported-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25s390/qeth: fix kernel doc commentsHeiko Carstens2-6/+6
Fix kernel doc comments and remove incorrect kernel doc indicators. Acked-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25s390/qeth: add __printf format attribute to qeth_dbf_longtextHeiko Carstens1-0/+1
Allow the compiler to recognize and check format strings and parameters. As reported with allmodconfig and W=1: drivers/s390/net/qeth_core_main.c: In function ‘qeth_dbf_longtext’: drivers/s390/net/qeth_core_main.c:6190:9: error: function ‘qeth_dbf_longtext’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format] 6190 | vsnprintf(dbf_txt_buf, sizeof(dbf_txt_buf), fmt, args); | ^~~~~~~~~ Acked-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25s390/qeth: fix various format stringsHeiko Carstens1-7/+7
Various format strings don't match with types of parameters. Fix all of them. Acked-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-25s390/qeth: don't keep track of Input Queue countJulian Wiedmann2-11/+7
The only actual user of qdio.no_input_queues is qeth_qdio_establish(), and there we already have full awareness of the current Input Queue configuration (1 RX queue, plus potentially 1 TX Completion queue). So avoid this state tracking, and the ambiguity it brings with it. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.