| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We can remove the unnecessary "omapdss," prefix because
the omapdrm driver takes care of it when matching with
the driver table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Official vendor string is now "tpo" and not "toppoly".
Requires patch "omapdrm: panel: fix compatible vendor string for td028ttec1"
so that the driver understands both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add basic panel support for the Nokia N950. It must be tweaked a
little bit later, since the panel was built into the device
upside-down. Also the first 5 and the last 5 pixels are covered
by plastic.
Signed-off-By: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This improves LCD support for the Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Due to a mistake in documentation the DS0_PULL_UP_DOWN_EN macro was
mistakenly defined as an active high bit, however setting the bit
actually disables the internal pull resistor on the pin, so correct this
macro and introduce a new DS0_PULL_UP_DOWN_DIS macro with the proper bit
value set now that the documentation has been updated.
Change based on AM437x Techninal Reference Manual SPRUHL7G Revised June
2017 Section 7.2.1.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have
leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have
leading 0s
Converted using the following command:
$ find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec \
sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" \
-e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format
error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The newly added OMAP35xx Torpedo does not have a WiFi option, so
this patch moves the WL1283 binding and pin muxing to the
logicpd-torpedo-37xx-devkit since it's only applicable on that SOM
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
H. Nikolaus Schaller
Sebastian Reichel
Dave Gerlach
Peter Ujfalusi
Mathieu Malaterre
Adam Ford