| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.
Fixes: fe6f700d6cbb ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
cpsw_suspend()
|- cpsw_ndo_stop()
|- __hw_addr_ref_unsync_dev()
|- cpsw_purge_all_mc()
|- vlan_for_each()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.
Fixes: 15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.
Fixes: 1bbe0ecc2a1a ("net: phy: mscc: macsec initialization")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 14b41a2959fb ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.
Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized. Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce(). timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().
systemd--1995 2.... 552950018us : stmmac_suspend: 4994
ksoftirq-9 0..s2 553123133us : stmmac_tx_timer_arm: 2276
systemd--1995 0.... 553127896us : stmmac_resume: 5101
systemd--320 7...2 553132752us : stmmac_tx_timer_arm: 2276
(sd-exec-1999 5...2 553135204us : stmmac_tx_timer_arm: 2276
---------------------------------
pc : run_timer_softirq+0x468/0x5e0
lr : run_timer_softirq+0x570/0x5e0
Call trace:
run_timer_softirq+0x468/0x5e0
__do_softirq+0x124/0x398
irq_exit+0xd8/0xe0
__handle_domain_irq+0x6c/0xc0
gic_handle_irq+0x60/0xb0
el1_irq+0xb8/0x180
arch_cpu_idle+0x38/0x230
default_idle_call+0x24/0x3c
do_idle+0x1e0/0x2b8
cpu_startup_entry+0x28/0x48
secondary_start_kernel+0x1b4/0x208
Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: Leon Yu <leoyu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if an error occurred during mlx5_function_setup(), we
keep dev->state as DEVICE_STATE_UP.
Fixing it by adding a goto label.
Fixes: e161105e58da ("net/mlx5: Function setup/teardown procedures")
Signed-off-by: Shay Drory <shayd@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The correct way is to us the flow_cls_offload_flow_rule() wrapper
instead of f->rule directly.
Fixes: 4c3844d9e97e ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On sq closure when we free its descriptors, we should also update netdev
txq on completions which would not arrive. Otherwise if we reopen sqs
and attach them back, for example on fw fatal recovery flow, we may get
tx timeout.
Fixes: 29429f3300a3 ("net/mlx5e: Timeout if SQ doesn't flush during close")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Invoke mutex_destroy() to catch any errors.
Fixes: 2cc43b494a6c ("net/mlx5_core: Managing root flow table")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add del_sw_func cb for root ns. Now there is no need to
maintain a case of del_sw_func being null when freeing the node.
Fixes: 2cc43b494a6c ("net/mlx5_core: Managing root flow table")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Unmanaged flow tables doesn't have a parent and tree_put_node()
assume there is always a parent if cleaning is needed. fix that.
Fixes: 5281a0c90919 ("net/mlx5: fs_core: Introduce unmanaged flow tables")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix memory leak in mlx5_events_init(), in case
create_single_thread_workqueue() fails, events
struct should be freed.
Fixes: 5d3c537f9070 ("net/mlx5: Handle event of power detection in the PCIE slot")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In the cited commit inner_tirs argument was added to create and destroy
inner tirs, and no indication was added to mlx5e_modify_tirs_hash()
function. In order to have a consistent handling, use
inner_indir_tir[0].tirn in tirs destroy/modify function as an indication
to whether inner tirs are created.
Inner tirs are not created for representors and before this commit,
a call to mlx5e_modify_tirs_hash() was sending HW commands to
modify non-existent inner tirs.
Fixes: 46dc933cee82 ("net/mlx5e: Provide explicit directive if to create inner indirect tirs")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The TLS TIS object contains the dek/key ID.
By destroying the key first, the TIS would contain an invalid
non-existing key ID.
Reverse the destroy order, this also acheives the desired assymetry
between the destroy and the create flows.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After changing the parent_id to be the same for both NICs of same
The cited commit wrongly allow offload of tc redirect flows from
VF to uplink and vice versa when devcies are on different eswitch,
these cases aren't supported by HW.
Disallow the above offloads when devcies are on different eswitch
and VF LAG is not configured.
Fixes: f6dc1264f1c0 ("net/mlx5e: Disallow tc redirect offload cases we don't support")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver is reloading during recovery flow, it can't get new commands
till command interface is up again. Otherwise we may get to null pointer
trying to access non initialized command structures.
Add cmdif state to avoid processing commands while cmdif is not ready.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After driver creates (via FW command) an EQ for commands, the driver will
be informed on new commands completion by EQE. However, due to a race in
driver's internal command mode metadata update, some new commands will
still be miss-handled by driver as if we are in polling mode. Such commands
can get two non forced completion, leading to already freed command entry
access.
CREATE_EQ command, that maps EQ to the command queue must be posted to the
command queue while it is empty and no other command should be posted.
Add SW mechanism that once the CREATE_EQ command is about to be executed,
all other commands will return error without being sent to the FW. Allow
sending other commands only after successfully changing the driver's
internal command mode metadata.
We can safely return error to all other commands while creating the command
EQ, as all other commands might be sent from the user/application during
driver load. Application can rerun them later after driver's load was
finished.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When FW response to commands is very slow and all command entries in
use are waiting for completion we can have a race where commands can get
timeout before they get out of the queue and handled. Timeout
completion on uninitialized command will cause releasing command's
buffers before accessing it for initialization and then we will get NULL
pointer exception while trying access it. It may also cause releasing
buffers of another command since we may have timeout completion before
even allocating entry index for this command.
Add entry handling completion to avoid this race.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
A ticket was not released after a call of the function
"rxkad_decrypt_ticket" failed. Thus replace the jump target
"temporary_error_free_resp" by "temporary_error_free_ticket".
Fixes: 8c2f826dc3631 ("rxrpc: Don't put crypto buffers on the stack")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Markus Elfring <Markus.Elfring@web.de>
|
|
Fix a warning due to an uninitialised variable.
le included from ../fs/afs/fs_probe.c:11:
../fs/afs/fs_probe.c: In function 'afs_fileserver_probe_result':
../fs/afs/internal.h:1453:2: warning: 'rtt_us' may be used uninitialized in this function [-Wmaybe-uninitialized]
1453 | printk("[%-6.6s] "FMT"\n", current->comm ,##__VA_ARGS__)
| ^~~~~~
../fs/afs/fs_probe.c:35:15: note: 'rtt_us' was declared here
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
In cas_init_one(), "pdev" is requested by "pci_request_regions", but it
was not released after a call of the function “pci_write_config_byte”
failed. Thus replace the jump target “err_write_cacheline” by
"err_out_free_res".
Fixes: 1f26dac32057 ("[NET]: Add Sun Cassini driver.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_set_ageing_time has 2 callers:
- felix_set_ageing_time: from drivers/net/dsa/ocelot/felix.c
- ocelot_port_attr_ageing_set: from drivers/net/ethernet/mscc/ocelot.c
The issue described in the fixed commit below actually happened for the
felix_set_ageing_time code path only, since ocelot_port_attr_ageing_set
was already dividing by 1000. So to make both paths symmetrical (and to
fix addresses getting aged way too fast on Ocelot), stop dividing by
1000 at caller side altogether.
Fixes: c0d7eccbc761 ("net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to r8168 vendor driver DASHv3 chips like RTL8168fp/RTL8117
need a special addressing for OCP access.
Fix is compile-tested only due to missing test hardware.
Fixes: 1287723aa139 ("r8169: add support for RTL8117")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting from iputils s20190709 (used in Fedora 31), arping does not
support timeout being specified as a decimal:
$ arping -c 1 -I swp1 -b 192.0.2.66 -q -w 0.1
arping: invalid argument: '0.1'
Previously, such timeouts were rounded to an integer.
Fix this by specifying the timeout as an integer.
Fixes: a5ee171d087e ("selftests: mlxsw: qos_mc_aware: Add a test for UC awareness")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of reload fail, the mlxsw_sp->ports contains a pointer to a
freed memory (either by reload_down() or reload_up() error path).
Fix this by initializing the pointer to NULL and checking it before
dereferencing in split/unsplit/type_set callpaths.
Fixes: 24cc68ad6c46 ("mlxsw: core: Add support for reload")
Reported-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable is used by log_test() to check if the test case completely
successfully or not. In case it is not initialized at the start of a
test case, it is possible for the test case to fail despite not
encountering any errors.
Example:
```
...
TEST: Trap group statistics [ OK ]
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
TEST: Trap policer binding [FAIL]
Policer drop counter was not incremented
```
Failure of trap_policer_test() caused trap_policer_bind_test() to fail
as well.
Fix by adding missing initialization of the variable.
Fixes: 5fbff58e27a1 ("selftests: netdevsim: Add test cases for devlink-trap policers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the policer drop counter is retrieved when the jiffies value is
a multiple of 64, the counter will not be incremented.
This randomly breaks a selftest [1] the reads the counter twice and
checks that it was incremented:
```
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
```
Fix by always incrementing the counter by 1.
[1] tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh
Fixes: ad188458d012 ("netdevsim: Add devlink-trap policer support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit bdf6fa52f01b ("sctp: handle association restarts when the
socket is closed.") starts shutdown when an association is restarted,
if in SHUTDOWN-PENDING state and the socket is closed. However, the
rationale stated in that commit applies also when in SHUTDOWN-SENT
state - we don't want to move an association to ESTABLISHED state when
the socket has been closed, because that results in an association
that is unreachable from user space.
The problem scenario:
1. Client crashes and/or restarts.
2. Server (using one-to-one socket) calls close(). SHUTDOWN is lost.
3. Client reconnects using the same addresses and ports.
4. Server's association is restarted. The association and the socket
move to ESTABLISHED state, even though the server process has
closed its descriptor.
Also, after step 4 when the server process exits, some resources are
leaked in an attempt to release the underlying inet sock structure in
ESTABLISHED state:
IPv4: Attempt to release TCP socket in state 1 00000000377288c7
Fix by acting the same way as in SHUTDOWN-PENDING state. That is, if
an association is restarted in SHUTDOWN-SENT state and the socket is
closed, then start shutdown and don't move the association or the
socket to ESTABLISHED state.
Fixes: bdf6fa52f01b ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dst_cache_get() documents it must be used with BH disabled.
sysbot reported :
BUG: using smp_processor_id() in preemptible [00000000] code: /21697
caller is dst_cache_get+0x3a/0xb0 net/core/dst_cache.c:68
CPU: 0 PID: 21697 Comm: Not tainted 5.7.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x188/0x20d lib/dump_stack.c:118
check_preemption_disabled lib/smp_processor_id.c:47 [inline]
debug_smp_processor_id.cold+0x88/0x9b lib/smp_processor_id.c:57
dst_cache_get+0x3a/0xb0 net/core/dst_cache.c:68
tipc_udp_xmit.isra.0+0xb9/0xad0 net/tipc/udp_media.c:164
tipc_udp_send_msg+0x3e6/0x490 net/tipc/udp_media.c:244
tipc_bearer_xmit_skb+0x1de/0x3f0 net/tipc/bearer.c:526
tipc_enable_bearer+0xb2f/0xd60 net/tipc/bearer.c:331
__tipc_nl_bearer_enable+0x2bf/0x390 net/tipc/bearer.c:995
tipc_nl_bearer_enable+0x1e/0x30 net/tipc/bearer.c:1003
genl_family_rcv_msg_doit net/netlink/genetlink.c:673 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:718 [inline]
genl_rcv_msg+0x627/0xdf0 net/netlink/genetlink.c:735
netlink_rcv_skb+0x15a/0x410 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:746
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x537/0x740 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x882/0xe10 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6bf/0x7e0 net/socket.c:2362
___sys_sendmsg+0x100/0x170 net/socket.c:2416
__sys_sendmsg+0xec/0x1b0 net/socket.c:2449
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
RIP: 0033:0x45ca29
Fixes: e9c1a793210f ("tipc: add dst_cache support for udp media")
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rxhash is enabled on any ethernet port except the first in each CP
block, traffic flow is prevented. The analysis is below:
I've been investigating this afternoon, and what I've found, comparing
a kernel without 895586d5dc32 and with 895586d5dc32 applied is:
- The table programmed into the hardware via mvpp22_rss_fill_table()
appears to be identical with or without the commit.
- When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports
that c2.attr[0] and c2.attr[2] are written back containing:
- with 895586d5dc32, failing: 00200000 40000000
- without 895586d5dc32, working: 04000000 40000000
- When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as:
04000000 00000000
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) |
MVPP22_CLS_C2_ATTR0_QLOW(ql);
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
if (priv->hw_version == MVPP21)
port->first_rxq = port->id * port->nrxqs;
else
port->first_rxq = port->id * priv->max_port_rxqs;
Where:
if (priv->hw_version == MVPP21)
priv->max_port_rxqs = 8;
else
priv->max_port_rxqs = 32;
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of 00000000..0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of 00000100..0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of 00000200..0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before 895586d5dc32, it was:
mvpp2_write(priv, MVPP22_RSS_INDEX,
MVPP22_RSS_INDEX_QUEUE(port->first_rxq));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE,
MVPP22_RSS_TABLE_POINTER(port->id));
and after:
mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx));
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
mvpp2_cls_oversize_rxq_set() sets this up as:
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id),
(port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS));
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Fixes: 895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is some ambiguity in the RFC as to whether the ADD_ADDR HMAC is
the rightmost 64 bits of the entire hash or of the leftmost 160 bits
of the hash. The intention, as clarified with the author of the RFC,
is the entire hash.
This change returns the entire hash from
mptcp_crypto_hmac_sha (instead of only the first 160 bits), and moves
any truncation/selection operation on the hash to the caller.
Fixes: 12555a2d97e5 ("mptcp: use rightmost 64 bits in ADD_ADDR HMAC")
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Todd Malsbary <todd.malsbary@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When attaching a flow dissector program to a network namespace with
bpf(BPF_PROG_ATTACH, ...) we grab a reference to bpf_prog.
If netns gets destroyed while a flow dissector is still attached, and there
are no other references to the prog, we leak the reference and the program
remains loaded.
Leak can be reproduced by running flow dissector tests from selftests/bpf:
# bpftool prog list
# ./test_flow_dissector.sh
...
selftests: test_flow_dissector [PASS]
# bpftool prog list
4: flow_dissector name _dissect tag e314084d332a5338 gpl
loaded_at 2020-05-20T18:50:53+0200 uid 0
xlated 552B jited 355B memlock 4096B map_ids 3,4
btf_id 4
#
Fix it by detaching the flow dissector program when netns is going away.
Fixes: d58e468b1112 ("flow_dissector: implements flow dissector BPF hook")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200521083435.560256-1-jakub@cloudflare.com
|
|
In the function devm_platform_ioremap_resource(), if get resource
failed, the return value is ERR_PTR() not NULL. Thus it must be
replaced by IS_ERR(), or else it may result in crashes if a critical
error path is encountered.
Fixes: 0ce5ebd24d25 ("mfd: ioc3: Add driver for SGI IOC3 chip")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we can't find a ->dumpit callback for the requested
(family,type) pair, we fall back to (PF_UNSPEC,type). In effect, we're
in the same situation as if userspace had requested a PF_UNSPEC
dump. For RTM_GETROUTE, that handler is rtnl_dump_all, which calls all
the registered RTM_GETROUTE handlers.
The requested table id may or may not exist for all of those
families. commit ae677bbb4441 ("net: Don't return invalid table id
error when dumping all families") fixed the problem when userspace
explicitly requests a PF_UNSPEC dump, but missed the fallback case.
For example, when we pass ipv6.disable=1 to a kernel with
CONFIG_IP_MROUTE=y and CONFIG_IP_MROUTE_MULTIPLE_TABLES=y,
the (PF_INET6, RTM_GETROUTE) handler isn't registered, so we end up in
rtnl_dump_all, and listing IPv6 routes will unexpectedly print:
# ip -6 r
Error: ipv4: MR table does not exist.
Dump terminated
commit ae677bbb4441 introduced the dump_all_families variable, which
gets set when userspace requests a PF_UNSPEC dump. However, we can't
simply set the family to PF_UNSPEC in rtnetlink_rcv_msg in the
fallback case to get dump_all_families == true, because some messages
types (for example RTM_GETRULE and RTM_GETNEIGH) only register the
PF_UNSPEC handler and use the family to filter in the kernel what is
dumped to userspace. We would then export more entries, that userspace
would have to filter. iproute does that, but other programs may not.
Instead, this patch removes dump_all_families and updates the
RTM_GETROUTE handlers to check if the family that is being dumped is
their own. When it's not, which covers both the intentional PF_UNSPEC
dumps (as dump_all_families did) and the fallback case, ignore the
missing table id error.
Fixes: cb167893f41e ("net: Plumb support for filtering ipv4 and ipv6 multicast route dumps")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of error with MPLS support the code is misusing AF_INET
instead of AF_MPLS.
Fixes: 1b69e7e6c4da ("ipip: support MPLS over IPv4")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We cannot free record on any transient error because it leads to
losing previos data. Check socket error to know whether record must
be freed or not.
Fixes: d10523d0b3d7 ("net/tls: free the record on encryption error")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bpf_exec_tx_verdict() can return negative value for copied
variable. In that case this value will be pushed back to caller
and the real error code will be lost. Fix it using signed type and
checking for positive value.
Fixes: d10523d0b3d7 ("net/tls: free the record on encryption error")
Fixes: d3b18ad31f93 ("tls: add bpf support to sk_msg handling")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert to using IS_ERR() instead of NULL test for cpsw_ale_create()
error handling. Also fix to return negative error code from this error
handling case instead of 0 in.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpsw_ale_create() can return both NULL and PTR_ERR(), but all of
the caller only check NULL for error handling. This patch convert
it to only return PTR_ERR() in all error cases, and the caller using
IS_ERR() instead of NULL test.
Fixes: 4b41d3436796 ("net: ethernet: ti: cpsw: allow untagged traffic on host port")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once the traversal of the list is completed with list_for_each_entry(),
the iterator (node) will point to an invalid object. So passing this to
qrtr_local_enqueue() which is outside of the iterator block is erroneous
eventhough the object is not used.
So fix this by passing NULL to qrtr_local_enqueue().
Fixes: bdabad3e363d ("net: Add Qualcomm IPC router")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes: 728480f12442 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes data remnant seen when we fail to reserve space for a
nexthop group during a larger dump.
If we fail the reservation, we goto nla_put_failure and
cancel the message.
Reproduce with the following iproute2 commands:
=====================
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip link add dummy20 type dummy
ip link add dummy21 type dummy
ip link add dummy22 type dummy
ip link add dummy23 type dummy
ip link add dummy24 type dummy
ip link add dummy25 type dummy
ip link add dummy26 type dummy
ip link add dummy27 type dummy
ip link add dummy28 type dummy
ip link add dummy29 type dummy
ip link add dummy30 type dummy
ip link add dummy31 type dummy
ip link add dummy32 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip link set dummy3 up
ip link set dummy4 up
ip link set dummy5 up
ip link set dummy6 up
ip link set dummy7 up
ip link set dummy8 up
ip link set dummy9 up
ip link set dummy10 up
ip link set dummy11 up
ip link set dummy12 up
ip link set dummy13 up
ip link set dummy14 up
ip link set dummy15 up
ip link set dummy16 up
ip link set dummy17 up
ip link set dummy18 up
ip link set dummy19 up
ip link set dummy20 up
ip link set dummy21 up
ip link set dummy22 up
ip link set dummy23 up
ip link set dummy24 up
ip link set dummy25 up
ip link set dummy26 up
ip link set dummy27 up
ip link set dummy28 up
ip link set dummy29 up
ip link set dummy30 up
ip link set dummy31 up
ip link set dummy32 up
ip link set dummy33 up
ip link set dummy34 up
ip link set vrf-red up
ip link set vrf-blue up
ip link set dummyVRFred up
ip link set dummyVRFblue up
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip ro add 1.1.1.20/32 dev dummy20
ip ro add 1.1.1.21/32 dev dummy21
ip ro add 1.1.1.22/32 dev dummy22
ip ro add 1.1.1.23/32 dev dummy23
ip ro add 1.1.1.24/32 dev dummy24
ip ro add 1.1.1.25/32 dev dummy25
ip ro add 1.1.1.26/32 dev dummy26
ip ro add 1.1.1.27/32 dev dummy27
ip ro add 1.1.1.28/32 dev dummy28
ip ro add 1.1.1.29/32 dev dummy29
ip ro add 1.1.1.30/32 dev dummy30
ip ro add 1.1.1.31/32 dev dummy31
ip ro add 1.1.1.32/32 dev dummy32
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 20 via 1.1.1.20 dev dummy20
ip next add id 21 via 1.1.1.21 dev dummy21
ip next add id 22 via 1.1.1.22 dev dummy22
ip next add id 23 via 1.1.1.23 dev dummy23
ip next add id 24 via 1.1.1.24 dev dummy24
ip next add id 25 via 1.1.1.25 dev dummy25
ip next add id 26 via 1.1.1.26 dev dummy26
ip next add id 27 via 1.1.1.27 dev dummy27
ip next add id 28 via 1.1.1.28 dev dummy28
ip next add id 29 via 1.1.1.29 dev dummy29
ip next add id 30 via 1.1.1.30 dev dummy30
ip next add id 31 via 1.1.1.31 dev dummy31
ip next add id 32 via 1.1.1.32 dev dummy32
i=100
while [ $i -le 200 ]
do
ip next add id $i group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
echo $i
((i++))
done
ip next add id 999 group 1/2/3/4/5/6
ip next ls
========================
Fixes: ab84be7e54fc ("net: Initial nexthop code")
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot was able to trigger this trace [1], probably by using
a zero optlen.
While we are at it, cap optlen to IFNAMSIZ - 1 instead of IFNAMSIZ.
[1]
BUG: KMSAN: uninit-value in strnlen+0xf9/0x170 lib/string.c:569
CPU: 0 PID: 8807 Comm: syz-executor483 Not tainted 5.7.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
strnlen+0xf9/0x170 lib/string.c:569
dev_name_hash net/core/dev.c:207 [inline]
netdev_name_node_lookup net/core/dev.c:277 [inline]
__dev_get_by_name+0x75/0x2b0 net/core/dev.c:778
ax25_setsockopt+0xfa3/0x1170 net/ax25/af_ax25.c:654
__compat_sys_setsockopt+0x4ed/0x910 net/compat.c:403
__do_compat_sys_setsockopt net/compat.c:413 [inline]
__se_compat_sys_setsockopt+0xdd/0x100 net/compat.c:410
__ia32_compat_sys_setsockopt+0x62/0x80 net/compat.c:410
do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
do_fast_syscall_32+0x3bf/0x6d0 arch/x86/entry/common.c:398
entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f57dd9
Code: 90 e8 0b 00 00 00 f3 90 0f ae e8 eb f9 8d 74 26 00 89 3c 24 c3 90 90 90 90 90 90 90 90 90 90 90 90 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 002b:00000000ffae8c1c EFLAGS: 00000217 ORIG_RAX: 000000000000016e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000000101
RDX: 0000000000000019 RSI: 0000000020000000 RDI: 0000000000000004
RBP: 0000000000000012 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Local variable ----devname@ax25_setsockopt created at:
ax25_setsockopt+0xe6/0x1170 net/ax25/af_ax25.c:536
ax25_setsockopt+0xe6/0x1170 net/ax25/af_ax25.c:536
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In "wireguard: queueing: preserve flow hash across packet scrubbing", we
were required to slightly increase the size of the receive replay
counter to something still fairly small, but an increase nonetheless.
It turns out that we can recoup some of the additional memory overhead
by splitting up the prior union type into two distinct types. Before, we
used the same "noise_counter" union for both sending and receiving, with
sending just using a simple atomic64_t, while receiving used the full
replay counter checker. This meant that most of the memory being
allocated for the sending counter was being wasted. Since the old
"noise_counter" type increased in size in the prior commit, now is a
good time to split up that union type into a distinct "noise_replay_
counter" for receiving and a boring atomic64_t for sending, each using
neither more nor less memory than required.
Also, since sometimes the replay counter is accessed without
necessitating additional accesses to the bitmap, we can reduce cache
misses by hoisting the always-necessary lock above the bitmap in the
struct layout. We also change a "noise_replay_counter" stack allocation
to kmalloc in a -DDEBUG selftest so that KASAN doesn't trigger a stack
frame warning.
All and all, removing a bit of abstraction in this commit makes the code
simpler and smaller, in addition to the motivating memory usage
recuperation. For example, passing around raw "noise_symmetric_key"
structs is something that really only makes sense within noise.c, in the
one place where the sending and receiving keys can safely be thought of
as the same type of object; subsequent to that, it's important that we
uniformly access these through keypair->{sending,receiving}, where their
distinct roles are always made explicit. So this patch allows us to draw
that distinction clearly as well.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's important that we clear most header fields during encapsulation and
decapsulation, because the packet is substantially changed, and we don't
want any info leak or logic bug due to an accidental correlation. But,
for encapsulation, it's wrong to clear skb->hash, since it's used by
fq_codel and flow dissection in general. Without it, classification does
not proceed as usual. This change might make it easier to estimate the
number of innerflows by examining clustering of out of order packets,
but this shouldn't open up anything that can't already be inferred
otherwise (e.g. syn packet size inference), and fq_codel can be disabled
anyway.
Furthermore, it might be the case that the hash isn't used or queried at
all until after wireguard transmits the encrypted UDP packet, which
means skb->hash might still be zero at this point, and thus no hash
taken over the inner packet data. In order to address this situation, we
force a calculation of skb->hash before encrypting packet data.
Of course this means that fq_codel might transmit packets slightly more
out of order than usual. Toke did some testing on beefy machines with
high quantities of parallel flows and found that increasing the
reply-attack counter to 8192 takes care of the most pathological cases
pretty well.
Reported-by: Dave Taht <dave.taht@gmail.com>
Reviewed-and-tested-by: Toke Høiland-Jørgensen <toke@toke.dk>
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior we read the preshared key after dropping the handshake lock, which
isn't an actual crypto issue if it races, but it's still not quite
correct. So copy that part of the state into a temporary like we do with
the rest of the handshake state variables. Then we can release the lock,
operate on the temporary, and zero it out at the end of the function. In
performance tests, the impact of this was entirely unnoticable, probably
because those bytes are coming from the same cacheline as other things
that are being copied out in the same manner.
Reported-by: Matt Dunwoodie <ncon@noconroy.net>
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-10 switched to defaulting to -fno-common, which broke iproute2-5.4.
This was fixed in iproute-5.6, so switch to that. Because we're after a
stable testing surface, we generally don't like to bump these
unnecessarily, but in this case, being able to actually build is a basic
necessity.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Qiushi Wu
Grygorii Strashko
Antoine Tenart
Leon Yu
Tiezhu Yang
Shay Drory
Roi Dayan
Moshe Shemesh
Tariq Toukan
Maor Dickman
Eran Ben Elisha
David Howells
Vladimir Oltean
Heiner Kallweit
Amit Cohen
Jiri Pirko
Jonathan McDowell
Ido Schimmel
Valentin Longchamp
Jere Leppänen
Eric Dumazet
Russell King
Claudiu Manoil
Todd Malsbary
Jakub Sitnicki
Tang Bin
Sabrina Dubroca
Vadim Fedorenko
Wei Yongjun
Manivannan Sadhasivam
Michal Kubecek
Stephen Worley
Jason A. Donenfeld