| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Retrieve the API version running on the firmware and based on it detect
which features are available for usage.
The first one to be listed is the capability to change the MAC protocol
at runtime.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MC firmware gained recently a new command which can reconfigure the
running protocol on the underlying MAC. Add this new command which will
be used in the next patches in order to do a major reconfig on the
interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dpmac_get_api_version command will be used in the next patches to
determine if the current firmware is capable or not to change the
Ethernet protocol running on the MAC.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add device tree binding for the Lynx 28G SerDes PHY driver used on
Layerscape based SoCs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new generic PHY driver to support the Lynx 28G SerDes
block found on some of the Layerscape SoCs such as LX2160A.
At the moment, only the following Ethernet protocols are supported:
SGMII/1000Base-X and 10GBaseR.
SerDes lanes which are not running an Ethernet protocol or a currently
supported Ethenet protocol will be left as it was configured through the
RCW (Reset Configuration Word) at boot time.
At probe time, the platform driver will read the current
configuration of both PLLs found on a SerDes block and will determine
what protocols are supported using that PLL.
For example, if a PLL is configured to generate a clock net (frate) of
5GHz the only protocols sustained by that PLL are SGMII/1000Base-X
(using a quarter of the full clock rate) and QSGMII using the full clock
net frequency on the lane.
On the .set_mode() callback, the PHY driver will first check if the
requested operating mode (protocol) is even supported by the current PLL
configuration and will error out if not.
Then, the lane is reconfigured to run on the requested protocol.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the port-based default priority, IEEE 802.1Q-2018 allows the
Application Priority Table to define QoS classes (0 to 7) per IP DSCP
value (0 to 63).
In the absence of an app table entry for a packet with DSCP value X,
QoS classification for that packet falls back to other methods (VLAN PCP
or port-based default). The presence of an app table for DSCP value X
with priority Y makes the hardware classify the packet to QoS class Y.
As opposed to the default-prio where DSA exposes only a "set" in
dsa_switch_ops (because the port-based default is the fallback, it
always exists, either implicitly or explicitly), for DSCP priorities we
expose an "add" and a "del". The addition of a DSCP entry means trusting
that DSCP priority, the deletion means ignoring it.
Drivers that already trust (at least some) DSCP values can describe
their configuration in dsa_switch_ops :: port_get_dscp_prio(), which is
called for each DSCP value from 0 to 63.
Again, there can be more than one dcbnl app table entry for the same
DSCP value, DSA chooses the one with the largest configured priority.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port-based default QoS class is assigned to packets that lack a
VLAN PCP (or the port is configured to not trust the VLAN PCP),
an IP DSCP (or the port is configured to not trust IP DSCP), and packets
on which no tc-skbedit action has matched.
Similar to other drivers, this can be exposed to user space using the
DCB Application Priority Table. IEEE 802.1Q-2018 specifies in Table
D-8 - Sel field values that when the Selector is 1, the Protocol ID
value of 0 denotes the "Default application priority. For use when
application priority is not otherwise specified."
The way in which the dcbnl integration in DSA has been designed has to
do with its requirements. Andrew Lunn explains that SOHO switches are
expected to come with some sort of pre-configured QoS profile, and that
it is desirable for this to come pre-loaded into the DSA slave interfaces'
DCB application priority table.
In the dcbnl design, this is possible because calls to dcb_ieee_setapp()
can be initiated by anyone including being self-initiated by this device
driver.
However, what makes this challenging to implement in DSA is that the DSA
core manages the net_devices (effectively hiding them from drivers),
while drivers manage the hardware. The DSA core has no knowledge of what
individual drivers' QoS policies are. DSA could export to drivers a
wrapper over dcb_ieee_setapp() and these could call that function to
pre-populate the app priority table, however drivers don't have a good
moment in time to do this. The dsa_switch_ops :: setup() method gets
called before the net_devices are created (dsa_slave_create), and so is
dsa_switch_ops :: port_setup(). What remains is dsa_switch_ops ::
port_enable(), but this gets called upon each ndo_open. If we add app
table entries on every open, we'd need to remove them on close, to avoid
duplicate entry errors. But if we delete app priority entries on close,
what we delete may not be the initial, driver pre-populated entries, but
rather user-added entries.
So it is clear that letting drivers choose the timing of the
dcb_ieee_setapp() call is inappropriate. The alternative which was
chosen is to introduce hardware-specific ops in dsa_switch_ops, and
effectively hide dcbnl details from drivers as well. For pre-populating
the application table, dsa_slave_dcbnl_init() will call
ds->ops->port_get_default_prio() which is supposed to read from
hardware. If the operation succeeds, DSA creates a default-prio app
table entry. The method is called as soon as the slave_dev is
registered, but before we release the rtnl_mutex. This is done such that
user space sees the app table entries as soon as it sees the interface
being registered.
The fact that we populate slave_dev->dcbnl_ops with a non-NULL pointer
changes behavior in dcb_doit() from net/dcb/dcbnl.c, which used to
return -EOPNOTSUPP for any dcbnl operation where netdev->dcbnl_ops is
NULL. Because there are still dcbnl-unaware DSA drivers even if they
have dcbnl_ops populated, the way to restore the behavior is to make all
dcbnl_ops return -EOPNOTSUPP on absence of the hardware-specific
dsa_switch_ops method.
The dcbnl framework absurdly allows there to be more than one app table
entry for the same selector and protocol (in other words, more than one
port-based default priority). In the iproute2 dcb program, there is a
"replace" syntactical sugar command which performs an "add" and a "del"
to hide this away. But we choose the largest configured priority when we
call ds->ops->port_set_default_prio(), using __fls(). When there is no
default-prio app table entry left, the port-default priority is restored
to 0.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210113154139.1803705-2-olteanv@gmail.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some tests, such as Test d052: Add 1M filters with the same action, may
not work with a small timeout value.
Increase timeout to 24 seconds.
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
____napi_schedule() needs to be invoked with disabled interrupts due to
__raise_softirq_irqoff (in order not to corrupt the per-CPU list).
____napi_schedule() needs also to be invoked from an interrupt context
so that the raised-softirq is processed while the interrupt context is
left.
Add lockdep asserts for both conditions.
While this is the second time the irq/softirq check is needed, provide a
generic lockdep_assert_softirq_will_run() which is used by both caller.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add net device refcount tracker to macvlan.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the reference operation to lowerdev of macvlan to avoid
the potential UAF problem under the following known scenario:
Someone module puts the NETDEV_UNREGISTER event handler to a
work, and lowerdev is accessed in the work handler. But when
the work is excuted, lowerdev has been destroyed because upper
macvlan did not get reference to lowerdev correctly.
That likes as the scenario occurred by
commit 563bcbae3ba2 ("net: vlan: fix a UAF in vlan_dev_real_dev()").
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch increases the number of RX-FIFOs to 3 and the max TX-FIFO
depth to 16. This leads to the following default ring configuration.
CAN-2.0 mode:
| FIFO setup: TEF: 0x400: 8*12 bytes = 96 bytes
| FIFO setup: RX-0: FIFO 1/0x460: 32*20 bytes = 640 bytes
| FIFO setup: RX-1: FIFO 2/0x6e0: 32*20 bytes = 640 bytes
| FIFO setup: RX-2: FIFO 3/0x960: 16*20 bytes = 320 bytes
| FIFO setup: TX: FIFO 4/0xaa0: 8*16 bytes = 128 bytes
| FIFO setup: free: 224 bytes
CAN-FD mode:
| FIFO setup: TEF: 0x400: 4*12 bytes = 48 bytes
| FIFO setup: RX-0: FIFO 1/0x430: 16*76 bytes = 1216 bytes
| FIFO setup: RX-1: FIFO 2/0x8f0: 4*76 bytes = 304 bytes
| FIFO setup: TX: FIFO 3/0xa20: 4*72 bytes = 288 bytes
| FIFO setup: free: 192 bytes
With the previously added ethtool ring configuration support the RAM
on the chip can now be runtime configured between RX and TX buffers.
Link: https://lore.kernel.org/20220313083640.501791-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support ethtool based configuration for the TX IRQ
coalescing added in the previous patch.
Link: https://lore.kernel.org/20220313083640.501791-12-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds TX IRQ coalescing support to the driver.
The implemented algorithm is similar to the RX IRQ coalescing support
added in the previous patch.
Link: https://lore.kernel.org/20220313083640.501791-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support ethtool based configuration for the RX IRQ
coalescing added in the previous patch.
Link: https://lore.kernel.org/20220313083640.501791-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds RX IRQ coalescing support to the driver.
The mcp251xfd chip doesn't support proper hardware based coalescing,
so this patch tries to implemented it in software. The RX-FIFO offers
a "FIFO not empty" interrupt, which is used if no coalescing is
active.
With activated RX IRQ coalescing the "FIFO not empty" interrupt is
disabled in the RX IRQ handler and the "FIFO half full" or "FIFO full
interrupt" (depending on RX max coalesced frames IRQ) is used instead.
To avoid RX CAN frame starvation a hrtimer is setup with RX coalesce
usecs IRQ,on timer expiration the "FIFO not empty" is enabled again.
Support for ethtool configuration is added in the next patch.
Link: https://lore.kernel.org/20220313083640.501791-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds runtime configurable RX and TX ring parameters via
ethtool to the driver.
Link: https://lore.kernel.org/20220313083640.501791-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
So far the configuration of the hardware FIFOs is hard coded and
depend only on the selected CAN mode (CAN-2.0 or CAN-FD).
This patch updates the macros describing the ring, FIFO and RAM layout
to prepare for the next patches that add support for runtime
configurable ring parameters via ethtool.
Link: https://lore.kernel.org/20220313083640.501791-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch prepares the driver for runtime configurable RX and TX ring
parameters. The actual runtime config support will be added in the
next patch.
Link: https://lore.kernel.org/20220313083640.501791-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds basic ethtool support (to query the current and
maximum ring parameters) to the driver.
Link: https://lore.kernel.org/20220313083640.501791-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support for coalescing to the RAM layout calculation.
Link: https://lore.kernel.org/20220313083640.501791-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds a helper function to calculate the ring configuration
of the controller based on various constraints, like available RAM,
size of RX and TX objects, CAN-mode, number of FIFOs and FIFO depth.
Link: https://lore.kernel.org/20220313083640.501791-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of an erroneous ring configuration more RAM than available
might be used. Change the printf modifier to a signed int to properly
print this erroneous value.
Fixes: 83daa863f16b ("can: mcp251xfd: ring: update FIFO setup debug info")
Link: https://lore.kernel.org/20220313083640.501791-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the freeing of the "oskb", by using kfree_skb()
instead of kfree().
Fixes: 1574481bb3de ("vxcan: remove sk reference in peer skb")
Link: https://lore.kernel.org/all/20220311123741.382618-1-mkl@pengutronix.de
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case external PHY is used, we need to take care of embedded PHY.
Since there are no methods to disable this PHY from the MAC side and
keeping RMII reference clock, we need to suspend it.
This patch will reduce electrical noise (PHY is continuing to send FLPs)
and power consumption by 0,22W.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In most cases we use own mdio bus, there is no need to create and store
string for the PHY address.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already read chipid on probe. There is no need to read it on reset.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only difference is the reset code, so remove not needed duplicates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable binding the nfp driver to NFP3800 and NFP3803 devices.
The PCIE_SRAM offset is different for the NFP3800 device, which also
only supports a single explicit group.
Changes to Dirk's work:
* 48-bit dma addressing is not ready yet. Keep 40-bit dma addressing
for NFP3800.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NFP3800 has slightly different queue controller range bounds.
Use the static chip data instead of defines. This commit
still assumes unchanged descriptor format. Later datapath
changes will allow adjusting for descriptor accounting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The queue controller (QCP) is accessed based on a device specific
offset. The NFP3800 device also supports more queues.
Furthermore, the NFP3800 VFs also access the QCP differently to how the
NFP6000 VFs accesses it, though still indirectly. Fortunately, we can
remove the offset all together for both VF types. This is safe for
NFP6000 VFs since the offset was effectively a wrap around and only used
for convenience to have it set the same as the NFP6000 PF.
Use nfp_dev_info to store queue controller parameters.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for new chips instead of defines use dev_info constants
to store DMA mask length.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NFP3800 uses a different PCIe configuration to CPP expansion BAR offsets.
We don't need to differentiate between the NFP4000, NFP5000 and NFP6000
since they all use the same offsets.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for supporting new chip add a driver data structure
which will hold per-chip-version information such as register
offsets.
Plumb it through to the relevant functions (nfpcore and nfp_net).
For now only a very simple member holding chip names is added,
following commits will add more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make sure the device ID tables are in ascending order.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The model number for NFP3800 and newer devices can be completely
derived from PluDevice register without subtracting 0x10.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PCI_DEVICE_ID_NETRONOME_NFP6000_VF is available for use and
should be used instead of the PCI_DEVICE_NFP6000VF. Meanwhile,
PCI_DEVICE_NFP6000VF PCI ID is removed for not being used.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Multiple writes cause intermediate pointer values that do not
end on complete TX descriptors.
The QCP peripheral on the NFP provides a number of access
modes. In some access modes, the maximum amount to add must
be restricted to a 6bit value. The particular access mode
used by _nfp_qcp_ptr_add() has no such restrictions, so the
"< NFP_QCP_MAX_ADD" test is unnecessary.
Note that trying to add more that the configured ring size
in a single add will cause a QCP overflow, caught and handled
by the QCP peripheral.
Signed-off-by: Christo du Toit <christo.du.toit@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NFP driver ABI contains a bit for ring prioritization which
was never implemented in the initially envisioned form.
Remove it, and open up the possibility of reclaiming for other uses.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warning:
./drivers/net/ethernet/8390/mcf8390.c:414:2-9: line 414 is redundant
because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220311001756.12234-1-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdev_name_node_alt_create() and netdev_name_node_alt_destroy()
are only called by rtnetlink, so no need for exports.
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220310223952.558779-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In function netvsc_process_raw_pkt for VM_PKT_DATA_USING_XFER_PAGES
case there is already a 'return' statement which results 'break'
as dead code
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1646933534-29493-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both functions are only used by core networking code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220310143229.895319-1-hch@lst.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In review for commit 8ee7ec4890e2b ("net: ipa: embed interconnect
array in the power structure"), Jakub Kicinski suggested that a
follow-up patch use struct_size() when computing the size of the
IPA power structure, which ends with a flexible array member.
Do that.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220311162423.872645-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for creating filters for GTP-U and GTP-C in switchdev mode. Add
support for parsing GTP-specific options (QFI and PDU type) and TEID.
By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR
Note: GTP-U with outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Checking only protocol ids while searching for correct FVs can lead to a
situation, when incorrect FV will be added to the list. Incorrect means
that FV has correct protocol id but incorrect offset.
Call ice_get_sw_fv_list with ice_prot_lkup_ext struct which contains all
protocol ids with offsets.
With this modification allocating and collecting protocol ids list is
not longer needed.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a function that checks if a net device type is GTP.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Options are as follows: PDU_TYPE:QFI and they refernce to
the fields from the PDU Session Protocol. PDU Session data
is conveyed in GTP-U Extension Header.
GTP-U Extension Header is described in 3GPP TS 29.281.
PDU Session Protocol is described in 3GPP TS 38.415.
PDU_TYPE - indicates the type of the PDU Session Information (4 bits)
QFI - QoS Flow Identifier (6 bits)
# ip link add gtp_dev type gtp role sgsn
# tc qdisc add dev gtp_dev ingress
# tc filter add dev gtp_dev protocol ip parent ffff: \
flower \
enc_key_id 11 \
gtp_opts 1:8/ff:ff \
action mirred egress redirect dev eth0
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
Ioana Ciornei
Vladimir Oltean
Victor Nogueira
Sebastian Andrzej Siewior
Ziyang Xuan
Marc Kleine-Budde
Oleksij Rempel
Eric Dumazet
Dirk van der Merwe
Jakub Kicinski
Christo du Toit
Yang Li
Jakub Kicinski
Saurabh Sengar
Christoph Hellwig
Alex Elder
Marcin Szycik
Michal Swiatkowski
Wojciech Drewek