| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
drivers/net/ethernet/intel/igc/igc_i225.c:235 igc_write_nvm_srwr()
warn: loop overwrites return value 'ret_val'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The i225 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs) - much like i210, which is used as
inspiration for this patch. It enables two possible functions, namely
time stamping external events and periodic output signals.
The assignment of PHC functions to the four SDP can be freely chosen by
the user.
For the external events time stamping, when the SDP (configured as input
by user) level changes, an interrupt is generated and the kernel
Precision Time Protocol (PTP) is informed.
For the periodic output signals, the i225 is configured to generate them
(so the SDP level will change periodically) and the driver also has to
keep updating the time of the next level change. However, this work is
not necessary for some frequencies as the i225 takes care of them
(namely, anything with a half-cycle of 500ms, 250ms, 125ms or < 70ms).
While i225 allows up to four timers to be used to source the time used
on the external events or output signals, this patch uses only one of
those timers. Main reason is to keep it simple, as it's not clear how
these extra timers would be exposed to users. Note that currently a NIC
can expose a single PTP device.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The i225 device can produce one interrupt on the full second, much
like i210 - from where this patch is inspired.
This patch sets up the full second interruption on the i225 and when
receiving it, it sends a PPS event to PTP (Precision Time Protocol)
kernel subsystem.
The PTP subsystem exposes the PPS events via ioctl and sysfs, and one
can use the `testptp` tool (tools/testing/selftests/ptp) to check that
the events are being generated.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add new function which checks MTA_REGISTER if its filled correctly.
If not then writes again to same register.
There is possibility that i210 and i211 could not accept
MTA_REGISTER settings, specially when you add and remove
many of multicast addresses in short time.
Without this patch there is possibility that multicast settings will be
not always set correctly in hardware.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
i210 has a total of 24KB of transmit packet buffer. When in Qav mode,
this buffer is divided into four pieces, one for each Tx queue.
Currently, 8KB are given to each of the two SR queues and 4KB are given
to each of the two SP queues.
However, it was noticed that such distribution can make best effort
traffic (which would usually go to the SP queues when Qav is enabled, as
the SR queues would be used by ETF or CBS qdiscs for TSN-aware traffic)
perform poorly. Using iperf3 to measure, one could see the performance
of best effort traffic drop by nearly a third (from 935Mbps to 578Mbps),
with no TSN traffic competing.
This patch redistributes the 24KB to each queue equally: 6KB each. On
tests, there was no notable performance reduction of best effort traffic
performance when there was no TSN traffic competing.
Below, more details about the data collected:
All experiments were run using the following qdisc setup:
qdisc taprio 100: root refcnt 9 tc 4 map 3 3 3 2 3 0 0 3 3 3 3 3 3 3 3 3
queues offset 0 count 1 offset 1 count 1 offset 2 count 1 offset 3 count 1
clockid TAI base-time 0 cycle-time 10000000 cycle-time-extension 0
index 0 cmd S gatemask 0xf interval 10000000
qdisc etf 8045: parent 100:1 clockid TAI delta 1000000 offload on
deadline_mode off skip_sock_check off
TSN traffic, when enabled, had this characteristics:
Packet size: 1500 bytes
Transmission interval: 125us
----------------------------------
Without this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 578 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 460 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 579 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.08 GBytes 462 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.34 GBytes 577 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 461 Mbits/sec 1
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.36 GBytes 586 Mbits/sec 0.000 ms 0/1011407 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.05 GBytes 451 Mbits/sec 0.000 ms 0/778672 (0%)
----------------------------------
With this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 646 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 931 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 1
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 2.23 GBytes 956 Mbits/sec 0.000 ms 0/1650226 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.51 GBytes 649 Mbits/sec 0.000 ms 0/1120264 (0%)
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Report corrected bits.
v2: catch reg access errors (Saeed)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report what appears to be the standard block counts:
- 30.5.1.1.17 aFECCorrectedBlocks
- 30.5.1.1.18 aFECUncorrectableBlocks
Don't report the per-lane symbol counts, if those really
count symbols they are not what the standard calls for
(even if symbols seem like the most useful thing to count.)
Fingers crossed that fec_corrected_errors is not in symbols.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report corrected bits.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to pause statistics add stats for FEC.
The IEEE standard mandates two sets of counters:
- 30.5.1.1.17 aFECCorrectedBlocks
- 30.5.1.1.18 aFECUncorrectableBlocks
where block is a block of bits FEC operates on.
Each of these counters is defined per lane (PCS instance).
Multiple vendors provide number of corrected _bits_ rather
than/as well as blocks.
This set adds the 2 standard-based block counters and a extra
one for corrected bits.
Counters are exposed to user space via netlink in new attributes.
Each attribute carries an array of u64s, first element is
the total count, and the following ones are a per-lane break down.
Much like with pause stats the operation will not fail when driver
does not implement the get_fec_stats callback (nor can the driver
fail the operation by returning an error). If stats can't be
reported the relevant attributes will be empty.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor fec_prepare_data() a little bit to skip the body
of the function and exit on error. Currently the code
depends on the fact that we only have one call which
may fail between ethnl_ops_begin() and ethnl_ops_complete()
and simply saves the error code. This will get hairy with
the stats also being queried.
No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We'll need it for FEC stats as well.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling two copy_to_user() for very small regions has very high overhead.
Switch to inlined unsafe_put_user() to save one stac/clac sequence,
and avoid copy_to_user().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert system_wq queue_work() to schedule_work() which is
a wrapper around it, since the former is a rare construct.
Fixes: 7294380c5211 ("enetc: support PTP Sync packet one-step timestamping")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To reduce the processing of unnecessary mailbox command when PF supports
actively push its link status to VFs, VFs stop sending request link
status command in periodic service task in this case.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, VF updates its link status every second by send query command
to PF in periodic service task. If link stats of PF is changed, VF may
need at most one second to update its link status.
To reduce delay of link status between PF and VFs, PF actively push its
link status to VFs when its link status is updated. And to let VF know
PF supports this new feature, the link status changed mailbox command
adds one bit to indicate it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber
as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit
in the chip configure register.
The driver assumes the copper side is selected on probe, but this might
not be the case depending which page was last selected by the
bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior.
Select the copper page when probing to circumvent this.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF. Mostly this struct member was unused.
Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.
Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.
Basically unpack the "high bit means dynamic" logic
into bitfields.
Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.
Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.
This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them. This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.
In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
af_packet fanout uses RCU rules to ensure f->arr elements
are not dismantled before RCU grace period.
However, it lacks rcu accessors to make sure KCSAN and other tools
wont detect data races. Stupid compilers could also play games.
Fixes: dc99f600698d ("packet: Add fanout support.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Ethernet switches might only be able to support disabling multicast
snooping globally, which is an issue for example when several bridges
span the same physical device and request contradictory settings.
Propagate the return value of br_mc_disabled_update() such that this
limitation is transmitted correctly to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Normally, the bootloader will already initialize the MAC address
registers of the ENETC and the driver will just use them or generate a
random one, if it is not initialized.
Add a new way to provide the MAC address: via device tree. Besides the
usual 'mac-address' property, there is also the possibility to fetch it
via a NVMEM provider. The sl28 board stores the MAC address in the SPI
NOR flash OTP region. Having this will allow linux to fetch the MAC
address from there without being dependent on the bootloader.
No in-tree boards have the device tree properties set, thus for these,
this is a no-op.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
./drivers/net/ethernet/sfc/enum.h:80:7-28: duplicated argument to |
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the commit 1ddc3229ad3c ("skbuff: remove some unnecessary operation
in skb_segment_list()") introduces an issue very similar to the
one already fixed by commit 53475c5dd856 ("net: fix use-after-free when
UDP GRO with shared fraglist").
If the GSO skb goes though skb_clone() and pskb_expand_head() before
entering skb_segment_list(), the latter will unshare the frag_list
skbs and will release the old list. With the reverted commit in place,
when skb_segment_list() completes, skb->next points to the just
released list, and later on the kernel will hit UaF.
Note that since commit e0e3070a9bc9 ("udp: properly complete L4 GRO
over UDP tunnel packet") the critical scenario can be reproduced also
receiving UDP over vxlan traffic with:
NIC (NETIF_F_GRO_FRAGLIST enabled) -> vxlan -> UDP sink
Attaching a packet socket to the NIC will cause skb_clone() and the
tunnel decapsulation will call pskb_expand_head().
Fixes: 1ddc3229ad3c ("skbuff: remove some unnecessary operation in skb_segment_list()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following clang warning:
drivers/atm/idt77252.c:1787:1: warning: unused function
'idt77252_fbq_level' [-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the [g|s]et_pauseparam ethtool ops. It considers
that the chip doesn't support pause frame use in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Synopsis MAC controller supports auxiliary snapshot feature that
allows user to store a snapshot of the system time based on an external
event.
This patch add supports to the above mentioned feature. Users will be
able to triggered capturing the time snapshot from user-space using
application such as testptp or any other applications that uses the
PTP_EXTTS_REQUEST ioctl request.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting 10G without autonegotiation is invalid according to
phy_ethtool_ksettings_set(). Thus, we need to set it during
autonegotiation.
If 1G autonegotiation can't complete for quite a time, but there is
signal in line, switch line interface type to 10GBase-R, if supported,
in hope for link to be established.
And vice versa. If 10GBase-R link can't be established for quite a time,
and autonegotiation is enabled, and there is signal in line, switch line
interface type to appropriate 1G mode, i.e. 1000Base-X or SGMII, if
supported.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No functional changes, just move read link status routines below
autonegotiation configuration to make future functional changes more
distinct.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some SFP modules uses RX_LOS for link indication. In such cases link
will be always up, even without cable connected. RX_LOS changes will
trigger link_up()/link_down() upstream operations. Thus, check that SFP
link is operational before actual read link status.
If there is no SFP cage connected to the tranciever, check only PMD
Recieve Signal Detect register.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to create an RQ which is not registered as an XDP RQ. For example:
the trap-RQ doesn't register as an XDP RQ.
Fixes: 869c5f926247 ("net/mlx5e: Generalize open RQ")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There should be no spaces at the start of the line.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
void function return statements are not generally useful.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There should be a blank lines after declarations.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The bit-wise and of the action field with MLX5_ACCEL_ESP_ACTION_DECRYPT
is incorrect as MLX5_ACCEL_ESP_ACTION_DECRYPT is zero and not intended
to be a bit-flag. Fix this by using the == operator as was originally
intended.
Addresses-Coverity: ("Logically dead code")
Fixes: 7dfee4b1d79e ("net/mlx5: IPsec, Refactor SA handle creation and destruction")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cmd size is 8K so use kvzalloc().
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5dr_action is a generally used data structure, and there is an
union for different types of actions in it. The size of mlx5dr_action
is about 72 bytes, but for those actions with fewer fields, most of
the allocated memory is wasted.
Remove this union, and mlx5dr_action becomes a generic action header.
Then actions are dynamically allocated with needed memory, the data
for each action is stored right after the header.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
SF's hardware function id is already stored in mlx5_sf. Reuse it,
instead of querying the hw table.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
Sasha Neftin
Ederson de Souza
Grzegorz Siwik
Jakub Kicinski
Eric Dumazet
Yangbo Lu
Guangbin Huang
David Bauer
Paul M Stillwell Jr
Bruce Allan
Brett Creeley
Jesse Brandeburg
Scott W Taylor
Jacob Keller
Anirudh Venkataramanan
Florian Fainelli
Michael Walle
Wan Jiabing
Paolo Abeni
Jiapeng Chong
Heiner Kallweit
Tan Tee Min
Ivan Bornyakov
Aya Levin
Wenpeng Liang
Colin Ian King
Roi Dayan
Jianbo Liu
Parav Pandit