| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Document properties to configure soft start and discharge resistor
for LAB and IBB respectively.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-5-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Short-Circuit Protection (SCP) and Over-Current Protection (OCP) are
very important for regulators like LAB and IBB, which are designed to
provide from very small to relatively big amounts of current to the
device (normally, a display).
Now that this regulator supports both voltage setting and current
limiting in this driver, to me it looked like being somehow essential
to provide support for SCP and OCP, for two reasons:
1. SCP is a drastic measure to prevent damaging "more" hardware in
the worst situations, if any was damaged, preventing potentially
drastic issues;
2. OCP is a great way to protect the hardware that we're powering
through these regulators as if anything bad happens, the HW will
draw more current than expected: in this case, the OCP interrupt
will fire and the regulators will be immediately shut down,
preventing hardware damage in many cases.
Both interrupts were successfully tested in a "sort-of" controlled
manner, with the following methodology:
Short-Circuit Protection (SCP):
1. Set LAB/IBB to 4.6/-1.4V, current limit 200mA/50mA;
2. Connect a 10 KOhm resistor to LAB/IBB by poking the right traces
on a FxTec Pro1 smartphone for a very brief time (in short words,
"just a rapid touch with flying wires");
3. The Short-Circuit protection trips: IRQ raises, regulators get
cut. Recovery OK, test repeated without rebooting, OK.
Over-Current Protection (OCP):
1. Set LAB/IBB to the expected voltage to power up the display of
a Sony Xperia XZ Premium smartphone (Sharp LS055D1SX04), set
current limit to LAB 200mA, IBB 50mA (the values that this
display unit needs are 200/800mA);
2. Boot the kernel: OCP fires. Recovery never happens because
the selected current limit is too low, but that's expected.
Test OK.
3. Set LAB/IBB to the expected current limits for XZ Premium
(LAB 200mA, IBB 800mA), but lower than expected voltage,
specifically LAB 5.4V, IBB -5.6V (instead of 5.6, -5.8V);
4. Boot the kernel: OCP fires. Recovery never happens because
the selected voltage (still in the working range limits)
is producing a current draw of more than 200mA on LAB.
Test OK.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-6-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Soft start is required to avoid inrush current during LAB ramp-up and
IBB ramp-down, protecting connected hardware to which we supply voltage.
Since soft start is configurable on both LAB and IBB regulators, it
was necessary to add two DT properties, respectively "qcom,soft-start-us"
to control LAB ramp-up and "qcom,discharge-resistor-kohms" to control
the discharge resistor for IBB ramp-down, which obviously brought the
need of implementing a of_parse callback for both regulators.
Finally, also implement pull-down mode in order to avoid unpredictable
behavior when the regulators are disabled (random voltage spikes etc).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-4-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
LAB and IBB regulators can be current-limited by setting the
appropriate registers, but this operation is granted only after
sending an unlock code for secure access.
Besides the secure access, it would be possible to use the
regmap helper for get_current_limit, as there is no security
blocking reads, but I chose not to as to avoid having a very
big array containing current limits, especially for IBB.
That said, these regulators support current limiting for:
- LAB (pos): 200-1600mA, with 200mA per step (8 steps),
- IBB (neg): 0-1550mA, with 50mA per step (32 steps).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The LAB and IBB regulator have just one range and it is useless
to use linear_range ops, as these are used to express multiple
linear ranges.
Switch list_voltage and map_voltage callbacks to *_linear instead.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Implement {get,set}_voltage_sel, list_voltage, map_voltage with
the useful regulator regmap helpers in order to be able to manage
the voltage of LAB (positive) and IBB (negative) regulators.
In particular, the supported ranges are the following:
- LAB (pos): 4600mV to 6100mV with 100mV stepping,
- IBB (neg): -7700mV to -1400mV with 100mV stepping.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210113194214.522238-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the ternary condition which is a bad coding style
in the kernel
I also remove the defering configuration of the nxp,phase-shift.
The configuration is now done at parsing time. It save some memory
and it's better for comprehension.
I also use the OTP default configuration when the parameter is wrong
or not specified.
I think that it's better to use the default configuration from the chip
than an arbitrary value.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-7-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use a linear range to describe the voltages of the
bucks 1-6 instead of listing it one by one (via a macro)
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-6-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.
As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-5-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.
As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-4-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
nxp,phase-shift is an enum so use enum format to describe it.
Minimum and maximum values are also wrong.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210114174714.122561-3-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pf8x00 module build was not documented.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20210114174714.122561-2-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The platform data header was only used to pass platform
data from board files. We now populate the regulators
exclusively from device tree, so the header contents can
be moved into the regulator drivers.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The struct ab8500_regulator_platform_data was a leftover
since the days before we probed all regulators from the
device tree. The ab8500-ext regulator was the only used,
defining platform data and register intialization that
was never used for anything, a copy of a boardfile no
longer in use.
Delete the ab8500_regulator_platform_data and make the
ab8500-ext regulator reference the regulator init data
in the local file directly. We are 100% device tree
these days.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
Section 3.11 was incorrectly called 3.9, fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Change my email contact ahead of a likely painful eleven-month migration
to a certain cobalt enteprisey groupware cloud product that will totally
break my workflow. Some day I may get used to having to email being
sequestered behind both claret and cerulean oath2+sms 2fa layers, but
for now I'll stick with keying in one password to receive an email vs.
the required four.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the creator of SQPOLL io_uring dies (i.e. sqo_task), we don't want
its internals like ->files and ->mm to be poked by the SQPOLL task, it
have never been nice and recently got racy. That can happen when the
owner undergoes destruction and SQPOLL tasks tries to submit new
requests in parallel, and so calls io_sq_thread_acquire*().
That patch halts SQPOLL submissions when sqo_task dies by introducing
sqo_dead flag. Once set, the SQPOLL task must not do any submission,
which is synchronised by uring_lock as well as the new flag.
The tricky part is to make sure that disabling always happens, that
means either the ring is discovered by creator's do_exit() -> cancel,
or if the final close() happens before it's done by the creator. The
last is guaranteed by the fact that for SQPOLL the creator task and only
it holds exactly one file note, so either it pins up to do_exit() or
removed by the creator on the final put in flush. (see comments in
uring_flush() around file->f_count == 2).
One more place that can trigger io_sq_thread_acquire_*() is
__io_req_task_submit(). Shoot off requests on sqo_dead there, even
though actually we don't need to. That's because cancellation of
sqo_task should wait for the request before going any further.
note 1: io_disable_sqo_submit() does io_ring_set_wakeup_flag() so the
caller would enter the ring to get an error, but it still doesn't
guarantee that the flag won't be cleared.
note 2: if final __userspace__ close happens not from the creator
task, the file note will pin the ring until the task dies.
Fixed: b1b6b5a30dce8 ("kernel/io_uring: cancel io_uring before task works")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
files_cancel() should cancel all relevant requests and drop file notes,
so we should never have file notes after that, including on-exit fput
and flush. Add a WARN_ONCE to be sure.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A simple preparation change inlining io_uring_attempt_task_drop() into
io_uring_flush().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We expect io_rw_reissue() to take place only during submission with
uring_lock held. Add a lockdep annotation to check that invariant.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET is set in incompat feature
set, it means the cache device is created with obsoleted layout with
obso_bucket_site_hi. Now bcache does not support this feature bit, a new
BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE incompat feature bit is added
for a better layout to support large bucket size.
For the legacy compatibility purpose, if a cache device created with
obsoleted BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit, all bcache
devices attached to this cache set should be set to read-only. Then the
dirty data can be written back to backing device before re-create the
cache device with BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE feature bit
by the latest bcache-tools.
This patch checks BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit
when running a cache set and attach a bcache device to the cache set. If
this bit is set,
- When run a cache set, print an error kernel message to indicate all
following attached bcache device will be read-only.
- When attach a bcache device, print an error kernel message to indicate
the attached bcache device will be read-only, and ask users to update
to latest bcache-tools.
Such change is only for cache device whose bucket size >= 32MB, this is
for the zoned SSD and almost nobody uses such large bucket size at this
moment. If you don't explicit set a large bucket size for a zoned SSD,
such change is totally transparent to your bcache device.
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When large bucket feature was added, BCH_FEATURE_INCOMPAT_LARGE_BUCKET
was introduced into the incompat feature set. It used bucket_size_hi
(which was added at the tail of struct cache_sb_disk) to extend current
16bit bucket size to 32bit with existing bucket_size in struct
cache_sb_disk.
This is not a good idea, there are two obvious problems,
- Bucket size is always value power of 2, if store log2(bucket size) in
existing bucket_size of struct cache_sb_disk, it is unnecessary to add
bucket_size_hi.
- Macro csum_set() assumes d[SB_JOURNAL_BUCKETS] is the last member in
struct cache_sb_disk, bucket_size_hi was added after d[] which makes
csum_set calculate an unexpected super block checksum.
To fix the above problems, this patch introduces a new incompat feature
bit BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE, when this bit is set, it
means bucket_size in struct cache_sb_disk stores the order of power-of-2
bucket size value. When user specifies a bucket size larger than 32768
sectors, BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE will be set to
incompat feature set, and bucket_size stores log2(bucket size) more
than store the real bucket size value.
The obsoleted BCH_FEATURE_INCOMPAT_LARGE_BUCKET won't be used anymore,
it is renamed to BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET and still only
recognized by kernel driver for legacy compatible purpose. The previous
bucket_size_hi is renmaed to obso_bucket_size_hi in struct cache_sb_disk
and not used in bcache-tools anymore.
For cache device created with BCH_FEATURE_INCOMPAT_LARGE_BUCKET feature,
bcache-tools and kernel driver still recognize the feature string and
display it as "obso_large_bucket".
With this change, the unnecessary extra space extend of bcache on-disk
super block can be avoided, and csum_set() may generate expected check
sum as well.
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch adds the check for features which is incompatible for
current supported feature sets.
Now if the bcache device created by bcache-tools has features that
current kernel doesn't support, read_super() will fail with error
messoage. E.g. if an unsupported incompatible feature detected,
bcache register will fail with dmesg "bcache: register_bcache() error :
Unsupported incompatible feature found".
Fixes: d721a43ff69c ("bcache: increase super block version for cache device and backing device")
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch fixes the following typos,
from BCH_FEATURE_COMPAT_SUUP to BCH_FEATURE_COMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_INCOMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_RO_COMPAT_SUPP
Fixes: d721a43ff69c ("bcache: increase super block version for cache device and backing device")
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is no need to reassign pdev_set_uuid in the second loop iteration,
so move it to the place before second loop.
Signed-off-by: Yi Li <yili@winhong.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
HSDK has hardware floating point and the common use case is with
glibc+hf so enable that as default.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The kernel test robot reported a -5.8% performance regression on the
"poll2" test of will-it-scale, and bisected it to commit d55564cfc222
("x86: Make __put_user() generate an out-of-line call").
I didn't expect an out-of-line __put_user() to matter, because no normal
core code should use that non-checking legacy version of user access any
more. But I had overlooked the very odd poll() usage, which does a
__put_user() to update the 'revents' values of the poll array.
Now, Al Viro correctly points out that instead of updating just the
'revents' field, it would be much simpler to just copy the _whole_
pollfd entry, and then we could just use "copy_to_user()" on the whole
array of entries, the same way we use "copy_from_user()" a few lines
earlier to get the original values.
But that is not what we've traditionally done, and I worry that threaded
applications might be concurrently modifying the other fields of the
pollfd array. So while Al's suggestion is simpler - and perhaps worth
trying in the future - this instead keeps the "just update revents"
model.
To fix the performance regression, use the modern "unsafe_put_user()"
instead of __put_user(), with the proper "user_write_access_begin()"
guarding in place. This improves code generation enormously.
Link: https://lore.kernel.org/lkml/20210107134723.GA28532@xsang-OptiPlex-9020/
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Oliver Sang <oliver.sang@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Laight <David.Laight@aculab.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 757055ae8dedf5333af17b3b5b4b70ba9bc9da4e.
The commit caused that ttynull was used as the default console
on several systems[1][2][3]. As a result, the console was
blank even when a better alternative existed.
It happened when there was no console configured
on the command line and ttynull_init() was the first initcall
calling register_console().
Or it happened when /dev/ did not exist when console_on_rootfs()
was called. It was not able to open /dev/console even though
a console driver was registered. It tried to add ttynull console
but it obviously did not help. But ttynull became the preferred
console and was used by /dev/console when it was available later.
The commit tried to fix a historical problem that have been there
for ages. The primary motivation was the commit 3cffa06aeef7ece30f6
("printk/console: Allow to disable console output by using console=""
or console=null"). It provided a clean solution for a workaround
that was widely used and worked only by chance.
This revert causes that the console="" or console=null command line
options will again work only by chance. These options will cause that
a particular console will be preferred and the default (tty) ones
will not get enabled. There will be no console registered at
all. As a result there won't be stdin, stdout, and stderr for
the init process. But it worked exactly this way even before.
The proper solution has to fulfill many conditions:
+ Register ttynull only when explicitly required or as
the ultimate fallback.
+ ttynull should get associated with /dev/console but it must
not become preferred console when used as a fallback.
Especially, it must still be possible to replace it
by a better console later.
Such a change requires clean up of the register_console() code.
Otherwise, it would be even harder to follow. Especially, the use
of has_preferred_console and CON_CONSDEV flag is tricky. The clean
up is risky. The ordering of consoles is not well defined. And
any changes tend to break existing user settings.
Do the revert at the least risky solution for now.
[1] https://lore.kernel.org/linux-kselftest/20201221144302.GR4077@smile.fi.intel.com/
[2] https://lore.kernel.org/lkml/d2a3b3c0-e548-7dd1-730f-59bc5c04e191@synopsys.com/
[3] https://patchwork.ozlabs.org/project/linux-um/patch/20210105120128.10854-1-thomas@m3y3r.de/
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Vineet Gupta <vgupta@synopsys.com>
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
hwmon, specifically hwmon_num_channel_attrs, expects the config
array in the hwmon_channel_info structure to be terminated by
a zero entry. amd_energy does not honor this convention. As
result, a KASAN warning is possible. Fix this by adding an
additional entry and setting it to zero.
Fixes: 8abee9566b7e ("hwmon: Add amd_energy driver to report energy counters")
Signed-off-by: David Arcari <darcari@redhat.com>
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20210107144707.6927-1-darcari@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
dtc points out that the interrupts for some devices are not parsable:
picoxcell-pc3x2.dtsi:45.19-49.5: Warning (interrupts_property): /paxi/gem@30000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:51.21-55.5: Warning (interrupts_property): /paxi/dmac@40000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:57.21-61.5: Warning (interrupts_property): /paxi/dmac@50000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:233.21-237.5: Warning (interrupts_property): /rwid-axi/axi2pico@c0000000: Missing interrupt-parent
There are two VIC instances, so it's not clear which one needs to be
used. I found the BSP sources that reference VIC0, so use that:
https://github.com/r1mikey/meta-picoxcell/blob/master/recipes-kernel/linux/linux-picochip-3.0/0001-picoxcell-support-for-Picochip-picoXcell-SoC.patch
Acked-by: Jamie Iles <jamie@jamieiles.com>
Link: https://lore.kernel.org/r/20201230152010.3914962-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Showing the hctx flags for when BLK_MQ_F_TAG_HCTX_SHARED is set gives
something like:
root@debian:/home/john# more /sys/kernel/debug/block/sda/hctx0/flags
alloc_policy=FIFO SHOULD_MERGE|TAG_QUEUE_SHARED|3
Add the decoding for that flag.
Fixes: 32bc15afed04b ("blk-mq: Facilitate a shared sbitmap per tagset")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We had kernel panic, it is caused by unload module and last
close confirmation.
call trace:
[1196029.743127] free_sess+0x15/0x50 [rtrs_client]
[1196029.743128] rtrs_clt_close+0x4c/0x70 [rtrs_client]
[1196029.743129] ? rnbd_clt_unmap_device+0x1b0/0x1b0 [rnbd_client]
[1196029.743130] close_rtrs+0x25/0x50 [rnbd_client]
[1196029.743131] rnbd_client_exit+0x93/0xb99 [rnbd_client]
[1196029.743132] __x64_sys_delete_module+0x190/0x260
And in the crashdump confirmation kworker is also running.
PID: 6943 TASK: ffff9e2ac8098000 CPU: 4 COMMAND: "kworker/4:2"
#0 [ffffb206cf337c30] __schedule at ffffffff9f93f891
#1 [ffffb206cf337cc8] schedule at ffffffff9f93fe98
#2 [ffffb206cf337cd0] schedule_timeout at ffffffff9f943938
#3 [ffffb206cf337d50] wait_for_completion at ffffffff9f9410a7
#4 [ffffb206cf337da0] __flush_work at ffffffff9f08ce0e
#5 [ffffb206cf337e20] rtrs_clt_close_conns at ffffffffc0d5f668 [rtrs_client]
#6 [ffffb206cf337e48] rtrs_clt_close at ffffffffc0d5f801 [rtrs_client]
#7 [ffffb206cf337e68] close_rtrs at ffffffffc0d26255 [rnbd_client]
#8 [ffffb206cf337e78] free_sess at ffffffffc0d262ad [rnbd_client]
#9 [ffffb206cf337e88] rnbd_clt_put_dev at ffffffffc0d266a7 [rnbd_client]
The problem is both code path try to close same session, which lead to
panic.
To fix it, just skip the sess if the refcount already drop to 0.
Fixes: f7a7a5c228d4 ("block/rnbd: client: main functionality")
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Adding name to the Contributors List
Signed-off-by: Swapnil Ingle <ingleswapnil@gmail.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since dynamically allocate sglist is used for rnbd_iu, we can't free sg
table after send_usr_msg since the callback function (cqe.done) could
still access the sglist.
Otherwise KASAN reports UAF issue:
[ 4856.600257] BUG: KASAN: use-after-free in dma_direct_unmap_sg+0x53/0x290
[ 4856.600772] Read of size 4 at addr ffff888206af3a98 by task swapper/1/0
[ 4856.601729] CPU: 1 PID: 0 Comm: swapper/1 Kdump: loaded Tainted: G W 5.10.0-pserver #5.10.0-1+feature+linux+next+20201214.1025+0910d71
[ 4856.601748] Hardware name: Supermicro Super Server/X11DDW-L, BIOS 3.3 02/21/2020
[ 4856.601766] Call Trace:
[ 4856.601785] <IRQ>
[ 4856.601822] dump_stack+0x99/0xcb
[ 4856.601856] ? dma_direct_unmap_sg+0x53/0x290
[ 4856.601888] print_address_description.constprop.7+0x1e/0x230
[ 4856.601913] ? freeze_kernel_threads+0x73/0x73
[ 4856.601965] ? mark_held_locks+0x29/0xa0
[ 4856.602019] ? dma_direct_unmap_sg+0x53/0x290
[ 4856.602039] ? dma_direct_unmap_sg+0x53/0x290
[ 4856.602079] kasan_report.cold.9+0x37/0x7c
[ 4856.602188] ? mlx5_ib_post_recv+0x430/0x520 [mlx5_ib]
[ 4856.602209] ? dma_direct_unmap_sg+0x53/0x290
[ 4856.602256] dma_direct_unmap_sg+0x53/0x290
[ 4856.602366] complete_rdma_req+0x188/0x4b0 [rtrs_client]
[ 4856.602451] ? rtrs_clt_close+0x80/0x80 [rtrs_client]
[ 4856.602535] ? mlx5_ib_poll_cq+0x48b/0x16e0 [mlx5_ib]
[ 4856.602589] ? radix_tree_insert+0x3a0/0x3a0
[ 4856.602610] ? do_raw_spin_lock+0x119/0x1d0
[ 4856.602647] ? rwlock_bug.part.1+0x60/0x60
[ 4856.602740] rtrs_clt_rdma_done+0x3f7/0x670 [rtrs_client]
[ 4856.602804] ? rtrs_clt_rdma_cm_handler+0xda0/0xda0 [rtrs_client]
[ 4856.602857] ? check_flags.part.31+0x6c/0x1f0
[ 4856.602927] ? rcu_read_lock_sched_held+0xaf/0xe0
[ 4856.602963] ? rcu_read_lock_bh_held+0xc0/0xc0
[ 4856.603137] __ib_process_cq+0x10a/0x350 [ib_core]
[ 4856.603309] ib_poll_handler+0x41/0x1c0 [ib_core]
[ 4856.603358] irq_poll_softirq+0xe6/0x280
[ 4856.603392] ? lockdep_hardirqs_on_prepare+0x111/0x210
[ 4856.603446] __do_softirq+0x10d/0x646
[ 4856.603540] asm_call_irq_on_stack+0x12/0x20
[ 4856.603563] </IRQ>
[ 4856.605096] Allocated by task 8914:
[ 4856.605510] kasan_save_stack+0x19/0x40
[ 4856.605532] __kasan_kmalloc.constprop.7+0xc1/0xd0
[ 4856.605552] __kmalloc+0x155/0x320
[ 4856.605574] __sg_alloc_table+0x155/0x1c0
[ 4856.605594] sg_alloc_table+0x1f/0x50
[ 4856.605620] send_msg_sess_info+0x119/0x2e0 [rnbd_client]
[ 4856.605646] remap_devs+0x71/0x210 [rnbd_client]
[ 4856.605676] init_sess+0xad8/0xe10 [rtrs_client]
[ 4856.605706] rtrs_clt_reconnect_work+0xd6/0x170 [rtrs_client]
[ 4856.605728] process_one_work+0x521/0xa90
[ 4856.605748] worker_thread+0x65/0x5b0
[ 4856.605769] kthread+0x1f2/0x210
[ 4856.605789] ret_from_fork+0x22/0x30
[ 4856.606159] Freed by task 8914:
[ 4856.606559] kasan_save_stack+0x19/0x40
[ 4856.606580] kasan_set_track+0x1c/0x30
[ 4856.606601] kasan_set_free_info+0x1b/0x30
[ 4856.606622] __kasan_slab_free+0x108/0x150
[ 4856.606642] slab_free_freelist_hook+0x64/0x190
[ 4856.606661] kfree+0xe2/0x650
[ 4856.606681] __sg_free_table+0xa4/0x100
[ 4856.606707] send_msg_sess_info+0x1d6/0x2e0 [rnbd_client]
[ 4856.606733] remap_devs+0x71/0x210 [rnbd_client]
[ 4856.606763] init_sess+0xad8/0xe10 [rtrs_client]
[ 4856.606792] rtrs_clt_reconnect_work+0xd6/0x170 [rtrs_client]
[ 4856.606813] process_one_work+0x521/0xa90
[ 4856.606833] worker_thread+0x65/0x5b0
[ 4856.606853] kthread+0x1f2/0x210
[ 4856.606872] ret_from_fork+0x22/0x30
The solution is to free iu's sgtable after the iu is not used anymore.
And also move sg_alloc_table into rnbd_get_iu accordingly.
Fixes: 5a1328d0c3a7 ("block/rnbd-clt: Dynamically allocate sglist for rnbd_iu")
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
KASAN detect following BUG:
[ 778.215311] ==================================================================
[ 778.216696] BUG: KASAN: use-after-free in rnbd_srv_sess_dev_force_close+0x38/0x60 [rnbd_server]
[ 778.219037] Read of size 8 at addr ffff88b1d6516c28 by task tee/8842
[ 778.220500] CPU: 37 PID: 8842 Comm: tee Kdump: loaded Not tainted 5.10.0-pserver #5.10.0-1+feature+linux+next+20201214.1025+0910d71
[ 778.220529] Hardware name: Supermicro Super Server/X11DDW-L, BIOS 3.3 02/21/2020
[ 778.220555] Call Trace:
[ 778.220609] dump_stack+0x99/0xcb
[ 778.220667] ? rnbd_srv_sess_dev_force_close+0x38/0x60 [rnbd_server]
[ 778.220715] print_address_description.constprop.7+0x1e/0x230
[ 778.220750] ? freeze_kernel_threads+0x73/0x73
[ 778.220896] ? rnbd_srv_sess_dev_force_close+0x38/0x60 [rnbd_server]
[ 778.220932] ? rnbd_srv_sess_dev_force_close+0x38/0x60 [rnbd_server]
[ 778.220994] kasan_report.cold.9+0x37/0x7c
[ 778.221066] ? kobject_put+0x80/0x270
[ 778.221102] ? rnbd_srv_sess_dev_force_close+0x38/0x60 [rnbd_server]
[ 778.221184] rnbd_srv_sess_dev_force_close+0x38/0x60 [rnbd_server]
[ 778.221240] rnbd_srv_dev_session_force_close_store+0x6a/0xc0 [rnbd_server]
[ 778.221304] ? sysfs_file_ops+0x90/0x90
[ 778.221353] kernfs_fop_write+0x141/0x240
[ 778.221451] vfs_write+0x142/0x4d0
[ 778.221553] ksys_write+0xc0/0x160
[ 778.221602] ? __ia32_sys_read+0x50/0x50
[ 778.221684] ? lockdep_hardirqs_on_prepare+0x13d/0x210
[ 778.221718] ? syscall_enter_from_user_mode+0x1c/0x50
[ 778.221821] do_syscall_64+0x33/0x40
[ 778.221862] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 778.221896] RIP: 0033:0x7f4affdd9504
[ 778.221928] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f 80 00 00 00 00 48 8d 05 f9 61 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53
[ 778.221956] RSP: 002b:00007fffebb36b28 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 778.222011] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f4affdd9504
[ 778.222038] RDX: 0000000000000002 RSI: 00007fffebb36c50 RDI: 0000000000000003
[ 778.222066] RBP: 00007fffebb36c50 R08: 0000556a151aa600 R09: 00007f4affeb1540
[ 778.222094] R10: fffffffffffffc19 R11: 0000000000000246 R12: 0000556a151aa520
[ 778.222121] R13: 0000000000000002 R14: 00007f4affea6760 R15: 0000000000000002
[ 778.222764] Allocated by task 3212:
[ 778.223285] kasan_save_stack+0x19/0x40
[ 778.223316] __kasan_kmalloc.constprop.7+0xc1/0xd0
[ 778.223347] kmem_cache_alloc_trace+0x186/0x350
[ 778.223382] rnbd_srv_rdma_ev+0xf16/0x1690 [rnbd_server]
[ 778.223422] process_io_req+0x4d1/0x670 [rtrs_server]
[ 778.223573] __ib_process_cq+0x10a/0x350 [ib_core]
[ 778.223709] ib_cq_poll_work+0x31/0xb0 [ib_core]
[ 778.223743] process_one_work+0x521/0xa90
[ 778.223773] worker_thread+0x65/0x5b0
[ 778.223802] kthread+0x1f2/0x210
[ 778.223833] ret_from_fork+0x22/0x30
[ 778.224296] Freed by task 8842:
[ 778.224800] kasan_save_stack+0x19/0x40
[ 778.224829] kasan_set_track+0x1c/0x30
[ 778.224860] kasan_set_free_info+0x1b/0x30
[ 778.224889] __kasan_slab_free+0x108/0x150
[ 778.224919] slab_free_freelist_hook+0x64/0x190
[ 778.224947] kfree+0xe2/0x650
[ 778.224982] rnbd_destroy_sess_dev+0x2fa/0x3b0 [rnbd_server]
[ 778.225011] kobject_put+0xda/0x270
[ 778.225046] rnbd_srv_sess_dev_force_close+0x30/0x60 [rnbd_server]
[ 778.225081] rnbd_srv_dev_session_force_close_store+0x6a/0xc0 [rnbd_server]
[ 778.225111] kernfs_fop_write+0x141/0x240
[ 778.225140] vfs_write+0x142/0x4d0
[ 778.225169] ksys_write+0xc0/0x160
[ 778.225198] do_syscall_64+0x33/0x40
[ 778.225227] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 778.226506] The buggy address belongs to the object at ffff88b1d6516c00
which belongs to the cache kmalloc-512 of size 512
[ 778.227464] The buggy address is located 40 bytes inside of
512-byte region [ffff88b1d6516c00, ffff88b1d6516e00)
The problem is in the sess_dev release function we call
rnbd_destroy_sess_dev, and could free the sess_dev already, but we still
set the keep_id in rnbd_srv_sess_dev_force_close, which lead to use
after free.
To fix it, move the keep_id before the sysfs removal, and cache the
rnbd_srv_session for lock accessing,
Fixes: 786998050cbc ("block/rnbd-srv: close a mapped device from server side.")
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
lkp reboot following build error:
drivers/block/rnbd/rnbd-clt.c: In function 'rnbd_softirq_done_fn':
>> drivers/block/rnbd/rnbd-clt.c:387:2: error: implicit declaration of function 'sg_free_table_chained' [-Werror=implicit-function-declaration]
387 | sg_free_table_chained(&iu->sgt, RNBD_INLINE_SG_CNT);
| ^~~~~~~~~~~~~~~~~~~~~
The reason is CONFIG_SG_POOL is not enabled in the config, to
avoid such failure, select SG_POOL in Kconfig for RNBD_CLIENT.
Fixes: 5a1328d0c3a7 ("block/rnbd-clt: Dynamically allocate sglist for rnbd_iu")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Shakeel Butt reported in [1] that a user can request a task to be moved
to a resource group even if the task is already in the group. It just
wastes time to do the move operation which could be costly to send IPI
to a different CPU.
Add a sanity check to ensure that the move operation only happens when
the task is not already in the resource group.
[1] https://lore.kernel.org/lkml/CALvZod7E9zzHwenzf7objzGKsdBmVwTgEJ0nPgs0LUFU3SN5Pw@mail.gmail.com/
Fixes: e02737d5b826 ("x86/intel_rdt: Add tasks files")
Reported-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/962ede65d8e95be793cb61102cca37f7bb018e66.1608243147.git.reinette.chatre@intel.com
|
|
Currently, when moving a task to a resource group the PQR_ASSOC MSR is
updated with the new closid and rmid in an added task callback. If the
task is running, the work is run as soon as possible. If the task is not
running, the work is executed later in the kernel exit path when the
kernel returns to the task again.
Updating the PQR_ASSOC MSR as soon as possible on the CPU a moved task
is running is the right thing to do. Queueing work for a task that is
not running is unnecessary (the PQR_ASSOC MSR is already updated when
the task is scheduled in) and causing system resource waste with the way
in which it is implemented: Work to update the PQR_ASSOC register is
queued every time the user writes a task id to the "tasks" file, even if
the task already belongs to the resource group.
This could result in multiple pending work items associated with a
single task even if they are all identical and even though only a single
update with most recent values is needed. Specifically, even if a task
is moved between different resource groups while it is sleeping then it
is only the last move that is relevant but yet a work item is queued
during each move.
This unnecessary queueing of work items could result in significant
system resource waste, especially on tasks sleeping for a long time.
For example, as demonstrated by Shakeel Butt in [1] writing the same
task id to the "tasks" file can quickly consume significant memory. The
same problem (wasted system resources) occurs when moving a task between
different resource groups.
As pointed out by Valentin Schneider in [2] there is an additional issue
with the way in which the queueing of work is done in that the task_struct
update is currently done after the work is queued, resulting in a race with
the register update possibly done before the data needed by the update is
available.
To solve these issues, update the PQR_ASSOC MSR in a synchronous way
right after the new closid and rmid are ready during the task movement,
only if the task is running. If a moved task is not running nothing
is done since the PQR_ASSOC MSR will be updated next time the task is
scheduled. This is the same way used to update the register when tasks
are moved as part of resource group removal.
[1] https://lore.kernel.org/lkml/CALvZod7E9zzHwenzf7objzGKsdBmVwTgEJ0nPgs0LUFU3SN5Pw@mail.gmail.com/
[2] https://lore.kernel.org/lkml/20201123022433.17905-1-valentin.schneider@arm.com
[ bp: Massage commit message and drop the two update_task_closid_rmid()
variants. ]
Fixes: e02737d5b826 ("x86/intel_rdt: Add tasks files")
Reported-by: Shakeel Butt <shakeelb@google.com>
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/17aa2fb38fc12ce7bb710106b3e7c7b45acb9e94.1608243147.git.reinette.chatre@intel.com
|
|
bdev_evict_inode and bdev_free_inode are also called for the root inode
of bdevfs, for which bdev_alloc is never called. Move the zeroing o
f struct block_device and the initialization of the bd_bdi field into
bdev_alloc_inode to make sure they are initialized for the root inode
as well.
Fixes: e6cb53827ed6 ("block: initialize struct block_device in bdev_alloc")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Exclude RMII from modes that report 1 GbE support. Reduced MII supports
up to 100 MbE.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210107195818.3878-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ip_finish_output_gso() may call .ndo_features_check() even before the
skb has a L2 header. This conflicts with qeth_get_ip_version()'s attempt
to inspect the L2 header via vlan_eth_hdr().
Switch to vlan_get_protocol(), as already used further down in the
common qeth_features_check() path.
Fixes: f13ade199391 ("s390/qeth: run non-offload L3 traffic over common xmit path")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to insufficient locking, qeth_core_set_online() and
qeth_dev_layer2_store() can run in parallel, both attempting to load &
setup the discipline (and stepping on each other toes along the way).
A similar race can also occur between qeth_core_remove_device() and
qeth_dev_layer2_store().
Access to .discipline is meant to be protected by the discipline_mutex,
so add/expand the locking in qeth_core_remove_device() and
qeth_core_set_online().
Adjust the locking in qeth_l*_remove_device() accordingly, as it's now
handled by the callers in a consistent manner.
Based on an initial patch by Ursula Braun.
Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When qeth_dev_layer2_store() - holding the discipline_mutex - waits
inside qeth_l*_remove_device() for a qeth_do_reset() thread to complete,
we can hit a deadlock if qeth_do_reset() concurrently calls
qeth_set_online() and thus tries to aquire the discipline_mutex.
Move the discipline_mutex locking outside of qeth_set_online() and
qeth_set_offline(), and turn the discipline into a parameter so that
callers understand the dependency.
To fix the deadlock, we can now relax the locking:
As already established, qeth_l*_remove_device() waits for
qeth_do_reset() to complete. So qeth_do_reset() itself is under no risk
of having card->discipline ripped out while it's running, and thus
doesn't need to take the discipline_mutex.
Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For IPv6 traffic, mausezahn needs to be invoked with '-6'. Otherwise an
error is returned:
# ip netns exec me mausezahn veth1 -B 2001:db8:101::2 -A 2001:db8:91::1 -c 0 -t tcp "dp=1-1023, flags=syn"
Failed to set source IPv4 address. Please check if source is set to a valid IPv4 address.
Invalid command line parameters!
Fixes: 7c741868ceab ("selftests: Add torture tests to nexthop tests")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function nh_check_attr_group() is called to validate nexthop groups.
The intention of that code seems to have been to bounce all attributes
above NHA_GROUP_TYPE except for NHA_FDB. However instead it bounces all
these attributes except when NHA_FDB attribute is present--then it accepts
them.
NHA_FDB validation that takes place before, in rtm_to_nh_config(), already
bounces NHA_OIF, NHA_BLACKHOLE, NHA_ENCAP and NHA_ENCAP_TYPE. Yet further
back, NHA_GROUPS and NHA_MASTER are bounced unconditionally.
But that still leaves NHA_GATEWAY as an attribute that would be accepted in
FDB nexthop groups (with no meaning), so long as it keeps the address
family as unspecified:
# ip nexthop add id 1 fdb via 127.0.0.1
# ip nexthop add id 10 fdb via default group 1
The nexthop code is still relatively new and likely not used very broadly,
and the FDB bits are newer still. Even though there is a reproducer out
there, it relies on an improbable gateway arguments "via default", "via
all" or "via any". Given all this, I believe it is OK to reformulate the
condition to do the right thing and bounce NHA_GATEWAY.
Fixes: 38428d68719c ("nexthop: support for fdb ecmp nexthops")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of error, remove the nexthop group entry from the list to which
it was previously added.
Fixes: 430a049190de ("nexthop: Add support for nexthop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A reference was not taken for the current nexthop entry, so do not try
to put it in the error path.
Fixes: 430a049190de ("nexthop: Add support for nexthop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the error return paths don't kfree lmac and lmac->name
leading to some memory leaks. Fix this by adding two error return
paths that kfree these objects
Addresses-Coverity: ("Resource leak")
Fixes: 1463f382f58d ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210107123916.189748-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
AngeloGioacchino Del Regno
Adrien Grassein
Linus Walleij
Linus Torvalds
Viresh Kumar
Darrick J. Wong
Pavel Begunkov
Coly Li
Yi Li
Vineet Gupta
Petr Mladek
David Arcari
Arnd Bergmann
John Garry
Jack Wang
Swapnil Ingle
Guoqing Jiang
Paolo Bonzini
Fenghua Yu
Christoph Hellwig
Aleksander Jan Bajkowski
Julian Wiedmann
Ido Schimmel
Petr Machata
Colin Ian King