| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As with GPIO, UART and others, allow specifying the device index via the
aliases node in the device tree.
On embedded devices, there is often a combination of removable (e.g.
SD card) and non-removable MMC devices (e.g. eMMC).
Therefore the index might change depending on
* host of removable device
* removable card present or not
This makes it difficult to hardcode the root device, if it is on the
non-removable device. E.g. if SD card is present eMMC will be mmcblk1,
if SD card is not present at boot, eMMC will be mmcblk0.
Alternative solutions like PARTUUIDs do not cover the case where multiple
mmcblk devices contain the same image. This is a common issue on devices
that can boot both from eMMC (for regular boot) and SD cards (as a
temporary boot medium for development). When a firmware image is
installed to eMMC after a test boot via SD card, there will be no
reliable way to refer to a specific device using (PART)UUIDs oder
LABELs.
The demand for this feature has led to multiple attempts to implement
it, dating back at least to 2012 (see
https://www.spinics.net/lists/linux-mmc/msg26586.html for a previous
discussion from 2014).
All indices defined in the aliases node will be reserved for use by the
respective MMC device, moving the indices of devices that don't have an
alias up into the non-reserved range. If the aliases node is not found,
the driver will act as before.
This is a rebased and cleaned up version of
https://www.spinics.net/lists/linux-mmc/msg26588.html .
Based-on-patch-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lkml.org/lkml/2020/8/5/194
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200901085004.2512-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As for I2C and SPI, it now is possible to reserve a fixed index for
mmc/mmcblk devices.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200901085004.2512-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200831102324.12566-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There might be multiple reset GPIOs but dtschema has trouble parsing it
if there are no maxItems:
arch/arm/boot/dts/exynos5250-snow.dt.yaml: mmc3_pwrseq: reset-gpios: [[20, 2, 1], [20, 1, 1]] is too long
From schema: Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200831161147.13515-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The i.MX 8 DTSes use two compatibles so update the binding to fix
dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mn-evk.dt.yaml: mmc@30b40000:
compatible: ['fsl,imx8mn-usdhc', 'fsl,imx7d-usdhc'] is too long
From schema: Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml
arch/arm64/boot/dts/freescale/imx8mn-evk.dt.yaml: mmc@30b40000:
compatible: Additional items are not allowed ('fsl,imx7d-usdhc' was unexpected)
arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dt.yaml: mmc@30b40000:
compatible: ['fsl,imx8mn-usdhc', 'fsl,imx7d-usdhc'] is too long
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200829062505.4642-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The emmc2 interface on the bcm2711 supports DDR modes for eMMC devices
running at 3.3V. This allows to run eMMC module with 3.3V signaling voltage
at DDR52 mode on the Raspberry Pi 4 using a SD adapter:
clock: 52000000 Hz
actual clock: 50000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
Link: https://github.com/raspberrypi/linux/issues/3802
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1598651234-29826-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
CQHCI_ENABLE bit in CQHCI_CFG should be disabled
after msdc_cqe_disable(), and should be enabled before
msdc_ceq_enable() for MTK platform.
Add hook functions for cqhci_host_ops->pre_enable() and
cqhci_host_ops->post_disable().
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598520783-25250-3-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add pre_enable() and post_disable() for cqhci_host_ops.
Add hook functions before cqhci enable and
after cqhci disable for platforms need them.
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598520783-25250-2-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On sc7180 target, issues are observed with HS400 mode due to a
hardware limitation. If sdcc clock is dynamically gated and ungated,
the very next command is failing with command CRC/timeout errors.
To mitigate this issue, DLL phase has to be restored whenever sdcc
clock is gated dynamically. The restore_dll_config ensures this.
Enabling this flag with this change. And simply re-using the sdm845
target configuration for this flag.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1598541694-15694-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After all the previous refactorization, we can now populate mmc_ops
directly and don't need a layer inbetween. The NULL-pointer check and
the error printout are already done by the MMC core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-7-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHI needs to reset the SCC only, not the whole IP core. So, if tuning
fails, don't handle specifics in the generic TMIO core, but in the
specific drivers. For SDHI, we need to move around the reset routine a
bit. It is not modified.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some TMIO variants need specific actions in their reset routine, but
they are all based on a generic reset routine. So, the optional 'reset'
callback will now only take care of the additional stuff and we will
have a generic function around it. Less code, easier to maintain, and
much more readable. Code in tmio_mmc.c is untested but in my TC6387XB
datasheet the SDIO part is reset independently from the SD part, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After Yamada-san's refactorization introducing 'tmio_mmc_host_alloc', we
can populate mmc_ops directly and don't need a layer inbetween.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit a87852c6b8827b7fece78ae57d871d56e4348e30. It did fix
the issue, but was building on top of already wrong assumptions. The
driver missed that 'hw_reset' was only for resetting remote HW (card)
and not for the IP core. Since we fixed that in a previous patch, we can
now remove this patch to make it clear that 'reset' is for resetting the
IP core only. Also, cancelling DMA will only be called when actually
needed again. It will also allow for further cleanups and better
readability. Note that in addition to the revert, the call in
'tmio_mmc_execute_tuning' will be converted, too, to maintain the
current behaviour.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This driver got the usage of 'hw_reset' wrong and missed that it is used
to reset the remote HW (card) only, not the local one (controller). Move
everything to the proper 'reset' callback. Also, add the generic reset
code from TMIO, so we will ensure the same behaviour (it will get
refactored away in a later patch). This also means we need to drop
MMC_CAP_HW_RESET because this is currently not supported by our
hardware.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There is a one time delay because of a card detect debounce timer in the
controller IP. This timer runs as soon as power is applied to the module
regardless of whether a card is present or not and any writes to
SDHCI_POWER_ON will return 0 before it expires. This timeout has been
measured to be about 1 second in am654x and j721e.
Write-and-read-back in a loop on SDHCI_POWER_ON for a maximum of
1.5 seconds to make sure that the controller actually powers on.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200825170015.32285-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There seems to be no particular reason to only test for ARM, so allow
for build-testing on other platforms to increase coverage.
Build-tested on x86 with allyesconfig.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824171854.406157-1-alex.dewar90@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Value assigned to a variable(err) is never used, so remove it.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598265914-23606-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use kobj_to_dev() instead of container_of()
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1598230956-58523-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This adds the eMMC driver for the Sparx5 SoC. It is based upon the
designware IP, but requires some extra initialization and quirks.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200825081357.32354-3-lars.povlsen@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
Matthias Schiffer
Wolfram Sang
Krzysztof Kozlowski
Stefan Wahren
Chun-Hung Wu
Veerabhadrarao Badiganti
Faiz Abbas
Alex Dewar
Haibo Chen
Tian Tao
Lars Povlsen