| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
|
|
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify that with that sysctl turned off, DSCP prioritization and rewrite
works the same way as in qos_dscp_bridge test. However when the sysctl
is charged, there should be a reprioritization after routing stage,
which will be observed by a different DSCP rewrite on egress.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dscp_capture_install() and dscp_capture_uninstall() are going to be
useful for a test added by a following patch, move them therefore to
lib.sh together with related helpers.
While doing so, change the rule preference from mere DSCP value to
DSCP+100 in order to support adding captures of packets with DSCP of 0.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function lldpad_wait() will be useful for a test added by a
following patch. Likewise would the "sleep 5" with its extensive
comment.
Therefore move lldpad_wait() to lib.sh in order to allow reuse. Rename
it to lldpad_app_wait_set() to recognize that what this is intended to
wait on are the pending APP sets.
For the sleeping, add a function lldpad_app_wait_del(). That will serve
to hold the related explanatory comment (which edit for clarity), and as
a token in the caller to identify the sites where this sort of waiting
takes place. That will serve when/if a better way to handle this
business is found.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two problems in this test case:
- When indexing in bash associative array, the subscript is interpreted as
string, not as a variable name to be expanded.
- The keys stored to t0s and t1s are not DSCP values, but priority +
base (i.e. the logical DSCP value, not the full bitfield value).
In combination these two bugs conspire to make the test just work,
except it doesn't really test anything and always passes.
Fix the above two problems in obvious manner.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that exercises the new code. Send DSCP-tagged packets, and
observe how they are prioritized in the switch and the DSCP is updated
on egress again.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove test_bitmap noise which is a result of cut and paste error.
There is no need for this modprobe -q -r test_bitmap noise in this
test.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Test several aspects of offloading mirror to gretap and ip6gretap
netdevices that are specific to mlxsw, such as requirements for TTL and
TOS values.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a scale test capable of validating that offloaded network
functionality is indeed functional at scale when configured to
the different KVD profiles available.
Start by testing offloaded routes are functional at scale by
passing traffic on each one of them in turn.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a wrapper around mlxsw/mirror_gre_scale.sh that parameterized number
of offloadable mirrors on Spectrum machines.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test that it's possible to offload a given number of mirrors.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a wrapper around mlxsw/tc_flower_scale.sh that parameterizes the
generic tc flower scale test template with Spectrum-specific target
values.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add test of capacity to offload flower.
This is a generic portion of the test that is meant to be called from a
driver that supplies a particular number of rules to be tested with.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 routes in Spectrum are based on the kvd single-hash, but as it's
a hash we need to assume we cannot reach 100% of its capacity.
Add a wrapper that provides us with good/bad target numbers for the
Spectrum ASIC.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
[petrm@mellanox.com: Drop shebang.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This test aims for both stand alone and internal usage by the resource
infra. The test receives the number routes to offload and checks:
- The routes were offloaded correctly
- Traffic for each route.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a selftest that can be used to perform basic sanity of the devlink
resource API as well as test the behavior of KVD manipulation in the
driver.
This is the first case of a HW-only test - in order to test the devlink
resource a driver capable of exposing resources has to be provided
first.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Extracted two patches out of this patch. Tweaked
commit message.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This library builds on top of devlink_lib.sh and contains functionality
specific to Spectrum ASICs, e.g., re-partitioning the various KVD
sub-parts.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Split this out from another patch. Fix line length
in devlink_sp_read_kvd_defaults().]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add test for USB over IP driver. This test runs several tests on a device
specified in the -b <busid> argument and path to the usbip tools.
usbip_test.sh -b <busid> -p <usbip tools path>
e.g:
cd tools/testing selftests/drivers/usb/usbip
sudo ./usbip_test.sh -b 3-10.2 -p <yoursrctree>/tools/usb/usbip
This test should be run as root and user should build usbip tools before
running the test.
The usbip test isn't included in the Kselftest run as it requires user to
specify a device to run tests on.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some pieces of code are independent of hardware but are very tricky to
exercise through the normal userspace ABI or via debugfs hooks. Being
able to create mock unit tests and execute them through CI is vital.
Start by adding a central point where we can execute unit tests and
a parameter to enable them. This is disabled by default as the
expectation is that these tests will occasionally explode.
To facilitate integration with igt, any parameter beginning with
i915.igt__ is interpreted as a subtest executable independently via
igt/drv_selftest.
Two classes of selftests are recognised: mock unit tests and integration
tests. Mock unit tests are run as soon as the module is loaded, before
the device is probed. At that point there is no driver instantiated and
all hw interactions must be "mocked". This is very useful for writing
universal tests to exercise code not typically run on a broad range of
architectures. Alternatively, you can hook into the live selftests and
run when the device has been instantiated - hw interactions are real.
v2: Add a macro for compiling conditional code for mock objects inside
real objects.
v3: Differentiate between mock unit tests and late integration test.
v4: List the tests in natural order, use igt to sort after modparam.
v5: s/late/live/
v6: s/unsigned long/unsigned int/
v7: Use igt_ prefixes for long helpers.
v8: Deobfuscate macros overriding functions, stop using -I$(src)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170213171558.20942-1-chris@chris-wilson.co.uk
|
|
Directly merge drm-misc into drm-intel since Dave is on vacation and
we need the various drm-misc patches (fb format rework, drm mm fixes,
selftest framework and others). Also pulled back -rc2 in first to
resync with drm-intel-fixes and make sure I can reuse the exact rerere
solutions from drm-tip for safety, and because I'm lazy.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
First we introduce a smattering of infrastructure for writing selftests.
The idea is that we have a test module that exercises a particular
portion of the exported API, and that module provides a set of tests
that can either be run as an ensemble via kselftest or individually via
an igt harness (in this case igt/drm_mm). To accommodate selecting
individual tests, we export a boolean parameter to control selection of
each test - that is hidden inside a bunch of reusable boilerplate macros
to keep writing the tests simple.
v2: Choose a random random_seed unless one is specified by the user.
v3: More parameters to control max_iterations and max_prime of the
tests.
Testcase: igt/drm_mm
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161222083641.2691-7-chris@chris-wilson.co.uk
|
|
Although being a GPU driver most functionality of i915.ko depends upon
real hardware, many of its internal interfaces can be "mocked" and so
tested independently of any hardware. Expanding the test coverage is not
only useful for i915.ko, but should provide some integration tests for
core infrastructure as well.
Loading i915.ko with mock_selftests=-1 will cause it to execute its mock
tests then fail with -ENOTTY. If the driver is already loaded and bound
to hardware, it requires a few more steps to unbind, and so the simple
preliminary modprobe -r will fail.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-kselftest@vger.kernel.org
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
Linus Torvalds
Ido Schimmel
Petr Machata
Shuah Khan (Samsung OSG)
Yuval Mintz
Arkadi Sharshevsky
Greg Kroah-Hartman
Chris Wilson
Daniel Vetter