Age | Commit message (Collapse) | Author | Files | Lines |
|
Dummy write in capture master mode is used to gate
bus clocks. This write is useless in slave mode
as the clocks are not managed by slave.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When snd_pcm_stop_xrun() is called in interrupt routine,
substream context may have already been released.
Add protection on substream context.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Clocks do not need to be released on driver removal,
as this is already managed before.
Remove useless remove callback.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DMA configuration is not balanced on start/stop.
Move DMA configuration to trigger callback.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move counter handling to trigger start section
to manage multiple start/stop events.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
I2S supports 16 bits data in 32 channel length.
However the expected driver behavior, is to
set channel length to 16 bits when data format is 16 bits.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Because of regmap cache, interrupts may not be cleared
as expected.
Declare IFCR register as write only and make writings
to IFCR register unconditional.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SND_SOC_CROS_EC_CODEC depends on MFD_CROS_EC.
Add that dependency to SND_SOC_SDM845 to fix unmet direct dependencies
warning.
Fixes: 74c6ecf4194e (ASoC: qcom: Kconfig: select dmic for sdm845)
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch enables the reuse of kbl_da7219_max98927 machine driver to
support max98373. The same machine driver is modified for cases where one
amplifier is swapped out with another. Most of the changes are about
renaming the codec and codec_dai names, with minor differences due to
support for 24 bits in one case and 16 in the other.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently each SSI unit 's busif mode/adinr/dalign address is
registered by: (in busif4 case)
RSND_GEN_M_REG(SSI_BUSIF4_MODE, 0x500, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_ADINR,0x504, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_DALIGN, 0x508, 0x80)
But according to user manual 41.1.4 Register Configuration
ssi9 4/5/6/7 busif mode/adinr/dalign register address
( SSI9-[4/5/6/7]_BUSIF_[MODE/ADINR/DALIGN] )
are out of this rule.
This patch registers ssi9 4/5/6/7 mode/adinr/dalign register
as single register, and access these registers in case of
SSI9 BUSIF 4/5/6/7.
Fixes: commit 8c9d75033340 ("ASoC: rsnd: ssiu: Support BUSIF other than BUSIF0")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In data blocks of common isochronous packet for MOTU devices, PCM
frames are multiplexed in a shape of '24 bit * 4 Audio Pack', described
in IEC 61883-6. The frames are not aligned to quadlet.
For capture PCM substream, ALSA firewire-motu driver constructs PCM
frames by reading data blocks byte-by-byte. However this operation
includes bug for lower byte of the PCM sample. This brings invalid
content of the PCM samples.
This commit fixes the bug.
Reported-by: Peter Sjöberg <autopeter@gmail.com>
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 4641c9394010 ("ALSA: firewire-motu: add MOTU specific protocol layer")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ALSA bebob driver has an entry for Focusrite Saffire Pro 10 I/O. The
entry matches vendor_id in root directory and model_id in unit
directory of configuration ROM for IEEE 1394 bus.
On the other hand, configuration ROM of Focusrite Liquid Saffire 56
has the same vendor_id and model_id. This device is an application of
TCAT Dice (TCD2220 a.k.a Dice Jr.) however ALSA bebob driver can be
bound to it randomly instead of ALSA dice driver. At present, drivers
in ALSA firewire stack can not handle this situation appropriately.
This commit uses more identical mod_alias for Focusrite Saffire Pro 10
I/O in ALSA bebob driver.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 042a829d bus_info_length 4, crc_length 42, crc 33437
404 31333934 bus_name "1394"
408 f0649222 irmc 1, cmc 1, isc 1, bmc 1, pmc 0, cyc_clk_acc 100,
max_rec 9 (1024), max_rom 2, gen 2, spd 2 (S400)
40c 00130e01 company_id 00130e |
410 000606e0 device_id 01000606e0 | EUI-64 00130e01000606e0
root directory
-----------------------------------------------------------------
414 0009d31c directory_length 9, crc 54044
418 04000014 hardware version
41c 0c0083c0 node capabilities per IEEE 1394
420 0300130e vendor
424 81000012 --> descriptor leaf at 46c
428 17000006 model
42c 81000016 --> descriptor leaf at 484
430 130120c2 version
434 d1000002 --> unit directory at 43c
438 d4000006 --> dependent info directory at 450
unit directory at 43c
-----------------------------------------------------------------
43c 0004707c directory_length 4, crc 28796
440 1200a02d specifier id: 1394 TA
444 13010001 version: AV/C
448 17000006 model
44c 81000013 --> descriptor leaf at 498
dependent info directory at 450
-----------------------------------------------------------------
450 000637c7 directory_length 6, crc 14279
454 120007f5 specifier id
458 13000001 version
45c 3affffc7 (immediate value)
460 3b100000 (immediate value)
464 3cffffc7 (immediate value)
468 3d600000 (immediate value)
descriptor leaf at 46c
-----------------------------------------------------------------
46c 00056f3b leaf_length 5, crc 28475
470 00000000 textual descriptor
474 00000000 minimal ASCII
478 466f6375 "Focu"
47c 73726974 "srit"
480 65000000 "e"
descriptor leaf at 484
-----------------------------------------------------------------
484 0004a165 leaf_length 4, crc 41317
488 00000000 textual descriptor
48c 00000000 minimal ASCII
490 50726f31 "Pro1"
494 30494f00 "0IO"
descriptor leaf at 498
-----------------------------------------------------------------
498 0004a165 leaf_length 4, crc 41317
49c 00000000 textual descriptor
4a0 00000000 minimal ASCII
4a4 50726f31 "Pro1"
4a8 30494f00 "0IO"
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 040442e4 bus_info_length 4, crc_length 4, crc 17124
404 31333934 bus_name "1394"
408 e0ff8112 irmc 1, cmc 1, isc 1, bmc 0, pmc 0, cyc_clk_acc 255,
max_rec 8 (512), max_rom 1, gen 1, spd 2 (S400)
40c 00130e04 company_id 00130e |
410 018001e9 device_id 04018001e9 | EUI-64 00130e04018001e9
root directory
-----------------------------------------------------------------
414 00065612 directory_length 6, crc 22034
418 0300130e vendor
41c 8100000a --> descriptor leaf at 444
420 17000006 model
424 8100000e --> descriptor leaf at 45c
428 0c0087c0 node capabilities per IEEE 1394
42c d1000001 --> unit directory at 430
unit directory at 430
-----------------------------------------------------------------
430 000418a0 directory_length 4, crc 6304
434 1200130e specifier id
438 13000001 version
43c 17000006 model
440 8100000f --> descriptor leaf at 47c
descriptor leaf at 444
-----------------------------------------------------------------
444 00056f3b leaf_length 5, crc 28475
448 00000000 textual descriptor
44c 00000000 minimal ASCII
450 466f6375 "Focu"
454 73726974 "srit"
458 65000000 "e"
descriptor leaf at 45c
-----------------------------------------------------------------
45c 000762c6 leaf_length 7, crc 25286
460 00000000 textual descriptor
464 00000000 minimal ASCII
468 4c495155 "LIQU"
46c 49445f53 "ID_S"
470 41464649 "AFFI"
474 52455f35 "RE_5"
478 36000000 "6"
descriptor leaf at 47c
-----------------------------------------------------------------
47c 000762c6 leaf_length 7, crc 25286
480 00000000 textual descriptor
484 00000000 minimal ASCII
488 4c495155 "LIQU"
48c 49445f53 "ID_S"
490 41464649 "AFFI"
494 52455f35 "RE_5"
498 36000000 "6"
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: 25784ec2d034 ("ALSA: bebob: Add support for Focusrite Saffire/SaffirePro series")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I set 10 seconds for the timeout of the i915 audio component binding
with a hope that recent machines are fast enough to handle all probe
tasks in that period, but I was too optimistic. The binding may take
longer than that, and this caused a problem on the machine with both
audio and graphics driver modules loaded in parallel, as Paul Menzel
experienced. This problem haven't hit so often just because the KMS
driver is loaded in initrd on most machines.
As a simple workaround, extend the timeout to 60 seconds.
Fixes: f9b54e1961c7 ("ALSA: hda/i915: Allow delayed i915 audio component binding")
Reported-by: Paul Menzel <pmenzel+alsa-devel@molgen.mpg.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a WARN_ON(!tcp_skb_pcount(skb))
in tcp_send_loss_probe() [1]
This was caused by TCP_REPAIR sent skbs that inadvertenly
were missing a call to tcp_init_tso_segs()
[1]
WARNING: CPU: 1 PID: 0 at net/ipv4/tcp_output.c:2534 tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.0.0-rc7+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
panic+0x2cb/0x65c kernel/panic.c:214
__warn.cold+0x20/0x45 kernel/panic.c:571
report_bug+0x263/0x2b0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
fixup_bug arch/x86/kernel/traps.c:173 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271
do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:290
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973
RIP: 0010:tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Code: 88 fc ff ff 4c 89 ef e8 ed 75 c8 fb e9 c8 fc ff ff e8 43 76 c8 fb e9 63 fd ff ff e8 d9 75 c8 fb e9 94 f9 ff ff e8 bf 03 91 fb <0f> 0b e9 7d fa ff ff e8 b3 03 91 fb 0f b6 1d 37 43 7a 03 31 ff 89
RSP: 0018:ffff8880ae907c60 EFLAGS: 00010206
RAX: ffff8880a989c340 RBX: 0000000000000000 RCX: ffffffff85dedbdb
RDX: 0000000000000100 RSI: ffffffff85dee0b1 RDI: 0000000000000005
RBP: ffff8880ae907c90 R08: ffff8880a989c340 R09: ffffed10147d1ae1
R10: ffffed10147d1ae0 R11: ffff8880a3e8d703 R12: ffff888091b90040
R13: ffff8880a3e8d540 R14: 0000000000008000 R15: ffff888091b90860
tcp_write_timer_handler+0x5c0/0x8a0 net/ipv4/tcp_timer.c:583
tcp_write_timer+0x10e/0x1d0 net/ipv4/tcp_timer.c:607
call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers kernel/time/timer.c:1681 [inline]
__run_timers kernel/time/timer.c:1649 [inline]
run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
__do_softirq+0x266/0x95a kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x180/0x1d0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
smp_apic_timer_interrupt+0x14a/0x570 arch/x86/kernel/apic/apic.c:1062
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
</IRQ>
RIP: 0010:native_safe_halt+0x2/0x10 arch/x86/include/asm/irqflags.h:58
Code: ff ff ff 48 89 c7 48 89 45 d8 e8 59 0c a1 fa 48 8b 45 d8 e9 ce fe ff ff 48 89 df e8 48 0c a1 fa eb 82 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90
RSP: 0018:ffff8880a98afd78 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffffffff1125061 RBX: ffff8880a989c340 RCX: 0000000000000000
RDX: dffffc0000000000 RSI: 0000000000000001 RDI: ffff8880a989cbbc
RBP: ffff8880a98afda8 R08: ffff8880a989c340 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
R13: ffffffff889282f8 R14: 0000000000000001 R15: 0000000000000000
arch_cpu_idle+0x10/0x20 arch/x86/kernel/process.c:555
default_idle_call+0x36/0x90 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x386/0x570 kernel/sched/idle.c:262
cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:353
start_secondary+0x404/0x5c0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
Kernel Offset: disabled
Rebooting in 86400 seconds..
Fixes: 79861919b889 ("tcp: fix TCP_REPAIR xmit queue setup")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot was able to trigger another soft lockup [1]
I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.
This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list
[1]
watchdog: BUG: soft lockup - CPU#0 stuck for 123s! [syz-executor.2:10492]
Modules linked in:
irq event stamp: 27515
hardirqs last enabled at (27514): [<ffffffff81006673>] trace_hardirqs_on_thunk+0x1a/0x1c
hardirqs last disabled at (27515): [<ffffffff8100668f>] trace_hardirqs_off_thunk+0x1a/0x1c
softirqs last enabled at (32): [<ffffffff8632ee73>] x25_get_neigh+0xa3/0xd0 net/x25/x25_link.c:336
softirqs last disabled at (34): [<ffffffff86324bc3>] x25_find_socket+0x23/0x140 net/x25/af_x25.c:341
CPU: 0 PID: 10492 Comm: syz-executor.2 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__sanitizer_cov_trace_pc+0x4/0x50 kernel/kcov.c:97
Code: f4 ff ff ff e8 11 9f ea ff 48 c7 05 12 fb e5 08 00 00 00 00 e9 c8 e9 ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 55 48 89 e5 <48> 8b 75 08 65 48 8b 04 25 40 ee 01 00 65 8b 15 38 0c 92 7e 81 e2
RSP: 0018:ffff88806e94fc48 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffff1100d84dac5 RBX: 0000000000000001 RCX: ffffc90006197000
RDX: 0000000000040000 RSI: ffffffff86324bf3 RDI: ffff88806c26d628
RBP: ffff88806e94fc48 R08: ffff88806c1c6500 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: ffff88806c26d628
R13: ffff888090455200 R14: dffffc0000000000 R15: 0000000000000000
FS: 00007f3a107e4700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3a107e3db8 CR3: 00000000a5544000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__x25_find_socket net/x25/af_x25.c:327 [inline]
x25_find_socket+0x7d/0x140 net/x25/af_x25.c:342
x25_new_lci net/x25/af_x25.c:355 [inline]
x25_connect+0x380/0xde0 net/x25/af_x25.c:784
__sys_connect+0x266/0x330 net/socket.c:1662
__do_sys_connect net/socket.c:1673 [inline]
__se_sys_connect net/socket.c:1670 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1670
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f3a107e3c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e29
RDX: 0000000000000012 RSI: 0000000020000200 RDI: 0000000000000005
RBP: 000000000073c040 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f3a107e46d4
R13: 00000000004be362 R14: 00000000004ceb98 R15: 00000000ffffffff
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 10493 Comm: syz-executor.3 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:193 [inline]
RIP: 0010:queued_write_lock_slowpath+0x143/0x290 kernel/locking/qrwlock.c:86
Code: 4c 8d 2c 01 41 83 c7 03 41 0f b6 45 00 41 38 c7 7c 08 84 c0 0f 85 0c 01 00 00 8b 03 3d 00 01 00 00 74 1a f3 90 41 0f b6 55 00 <41> 38 d7 7c eb 84 d2 74 e7 48 89 df e8 cc aa 4e 00 eb dd be 04 00
RSP: 0018:ffff888085c47bd8 EFLAGS: 00000206
RAX: 0000000000000300 RBX: ffffffff89412b00 RCX: 1ffffffff1282560
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff89412b00
RBP: ffff888085c47c70 R08: 1ffffffff1282560 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: 00000000000000ff
R13: fffffbfff1282560 R14: 1ffff11010b88f7d R15: 0000000000000003
FS: 00007fdd04086700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fdd04064db8 CR3: 0000000090be0000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
queued_write_lock include/asm-generic/qrwlock.h:104 [inline]
do_raw_write_lock+0x1d6/0x290 kernel/locking/spinlock_debug.c:203
__raw_write_lock_bh include/linux/rwlock_api_smp.h:204 [inline]
_raw_write_lock_bh+0x3b/0x50 kernel/locking/spinlock.c:312
x25_insert_socket+0x21/0xe0 net/x25/af_x25.c:267
x25_bind+0x273/0x340 net/x25/af_x25.c:703
__sys_bind+0x23f/0x290 net/socket.c:1481
__do_sys_bind net/socket.c:1492 [inline]
__se_sys_bind net/socket.c:1490 [inline]
__x64_sys_bind+0x73/0xb0 net/socket.c:1490
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29
Fixes: 90c27297a9bf ("X.25 remove bkl in bind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: andrew hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This callback was removed some time ago, also remove the documentation.
Fixes: 1b6dd556c304 ("net: dsa: Remove prepare phase for FDB")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like commit e2ba732a1681 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before derefencing the encap pointer, commit e7cc082455cb ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
fixed_mdio_bus_init+0x283/0x1000 [fixed_phy]
? 0xffffffffc0e40000
? 0xffffffffc0e40000
? 0xffffffffc0e40000
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
Allocated by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
kmalloc include/linux/slab.h:545 [inline]
kzalloc include/linux/slab.h:740 [inline]
mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143
fixed_mdio_bus_init+0x163/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kfree+0xe1/0x270 mm/slub.c:3938
device_release+0x78/0x200 drivers/base/core.c:919
kobject_cleanup lib/kobject.c:662 [inline]
kobject_release lib/kobject.c:691 [inline]
kref_put include/linux/kref.h:67 [inline]
kobject_put+0x146/0x240 lib/kobject.c:708
put_device+0x1c/0x30 drivers/base/core.c:2060
__mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382
fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8881dc824c80
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 248 bytes inside of
2048-byte region [ffff8881dc824c80, ffff8881dc825480)
The buggy address belongs to the page:
page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0
flags: 0x2fffc0000010200(slab|head)
raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800
raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e065 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The intended optimization should be A ^ 0 = A, not A ^ -1 = A.
Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a4a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").
Fixes: bccb30254a4a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().
Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.
There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:
ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1
ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1
ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6
ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64
ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2
ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6
ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64
ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2
ip -n cl link del cl_veth
This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.
v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To communicate to PF each of ThunderX NIC VF uses mailbox which is
pair of 64 bit registers available to both VFn and PF.
This commit is to change the xcast message structure in order to
fit it into 64 bit.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.
This commit is to implement check of nicvf_msg_send_to_pf() result.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.
We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.
This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct STREERING to STEERING at macro name for BGX steering register.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a possible NULL pointer dereference in ip6erspan_set_version checking
nlattr data pointer
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 7549 Comm: syz-executor432 Not tainted 5.0.0-rc6-next-20190218
#37
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:ip6erspan_set_version+0x5c/0x350 net/ipv6/ip6_gre.c:1726
Code: 07 38 d0 7f 08 84 c0 0f 85 9f 02 00 00 49 8d bc 24 b0 00 00 00 c6 43
54 01 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f
85 9a 02 00 00 4d 8b ac 24 b0 00 00 00 4d 85 ed 0f
RSP: 0018:ffff888089ed7168 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8880869d6e58 RCX: 0000000000000000
RDX: 0000000000000016 RSI: ffffffff862736b4 RDI: 00000000000000b0
RBP: ffff888089ed7180 R08: 1ffff11010d3adcb R09: ffff8880869d6e58
R10: ffffed1010d3add5 R11: ffff8880869d6eaf R12: 0000000000000000
R13: ffffffff8931f8c0 R14: ffffffff862825d0 R15: ffff8880869d6e58
FS: 0000000000b3d880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000184 CR3: 0000000092cc5000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
ip6erspan_newlink+0x66/0x7b0 net/ipv6/ip6_gre.c:2210
__rtnl_newlink+0x107b/0x16c0 net/core/rtnetlink.c:3176
rtnl_newlink+0x69/0xa0 net/core/rtnetlink.c:3234
rtnetlink_rcv_msg+0x465/0xb00 net/core/rtnetlink.c:5192
netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2485
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5210
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1925
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg+0xdd/0x130 net/socket.c:631
___sys_sendmsg+0x806/0x930 net/socket.c:2136
__sys_sendmsg+0x105/0x1d0 net/socket.c:2174
__do_sys_sendmsg net/socket.c:2183 [inline]
__se_sys_sendmsg net/socket.c:2181 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2181
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440159
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fffa69156e8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440159
RDX: 0000000000000000 RSI: 0000000020001340 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000001 R09: 00000000004002c8
R10: 0000000000000011 R11: 0000000000000246 R12: 00000000004019e0
R13: 0000000000401a70 R14: 0000000000000000 R15: 0000000000000000
Modules linked in:
---[ end trace 09f8a7d13b4faaa1 ]---
RIP: 0010:ip6erspan_set_version+0x5c/0x350 net/ipv6/ip6_gre.c:1726
Code: 07 38 d0 7f 08 84 c0 0f 85 9f 02 00 00 49 8d bc 24 b0 00 00 00 c6 43
54 01 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f
85 9a 02 00 00 4d 8b ac 24 b0 00 00 00 4d 85 ed 0f
RSP: 0018:ffff888089ed7168 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8880869d6e58 RCX: 0000000000000000
RDX: 0000000000000016 RSI: ffffffff862736b4 RDI: 00000000000000b0
RBP: ffff888089ed7180 R08: 1ffff11010d3adcb R09: ffff8880869d6e58
R10: ffffed1010d3add5 R11: ffff8880869d6eaf R12: 0000000000000000
R13: ffffffff8931f8c0 R14: ffffffff862825d0 R15: ffff8880869d6e58
FS: 0000000000b3d880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000184 CR3: 0000000092cc5000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Fixes: 4974d5f678ab ("net: ip6_gre: initialize erspan_ver just for erspan tunnels")
Reported-and-tested-by: syzbot+30191cf1057abd3064af@syzkaller.appspotmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a port is added to a team, its initial state is derived
from netif_carrier_ok rather than netif_oper_up.
If it is carrier up but operationally down at the time of being
added, the port state.linkup will be set prematurely.
port state.linkup should be set consistently using
netif_oper_up rather than netif_carrier_ok.
Fixes: f1d22a1e0595 ("team: account for oper state")
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL8153-BD is used in Dell DA300 type-C dongle.
Added RTL8153-BD support to activate MAC address pass through on DA300.
Apply correction on previously submitted patch in net.git tree.
Signed-off-by: David Chen <david.chen7@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running Docker with userns isolation e.g. --userns-remap="default"
and spawning up some containers with CAP_NET_ADMIN under this realm, I
noticed that link changes on ipvlan slave device inside that container
can affect all devices from this ipvlan group which are in other net
namespaces where the container should have no permission to make changes
to, such as the init netns, for example.
This effectively allows to undo ipvlan private mode and switch globally to
bridge mode where slaves can communicate directly without going through
hostns, or it allows to switch between global operation mode (l2/l3/l3s)
for everyone bound to the given ipvlan master device. libnetwork plugin
here is creating an ipvlan master and ipvlan slave in hostns and a slave
each that is moved into the container's netns upon creation event.
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
* Spawn container & change ipvlan mode setting inside of it:
# docker run -dt --cap-add=NET_ADMIN --network cilium-net --name client -l app=test cilium/netperf
9fff485d69dcb5ce37c9e33ca20a11ccafc236d690105aadbfb77e4f4170879c
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
# docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns (mode switched to l2):
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
Same l3 -> l2 switch would also happen by creating another slave inside
the container's network namespace when specifying the existing cilium0
link to derive the actual (bond0) master:
# docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
2: cilium1@if4: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
One way to mitigate it is to check CAP_NET_ADMIN permissions of
the ipvlan master device's ns, and only then allow to change
mode or flags for all devices bound to it. Above two cases are
then disallowed after the patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bdbb ("sctp: avoid refreshing heartbeat timer too often")
Reported-by: Marcin Stojek <marcin.stojek@nokia.com>
Tested-by: Marcin Stojek <marcin.stojek@nokia.com>
Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, commit 7dcd57552008 ("x86/kvm/mmu: check if tdp/shadow
MMU reconfiguration is needed") offered some optimization to avoid
the unnecessary reconfiguration. Yet one scenario is broken - when
cpuid changes VM's maximum physical address width, reconfiguration
is needed to reset the reserved bits. Also, the TDP may need to
reset its shadow_root_level when this value is changed.
To fix this, a new field, maxphyaddr, is introduced in the extended
role structure to keep track of the configured guest physical address
width.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|