| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Construct a "one-armed router" topology and test that packets are
forwarded by the ASIC and that a copy of the packet is sent to the
kernel, which does not forward the packet again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both msg_zerocopy and udpgso_bench have udp zerocopy variants.
Exercise these as part of the standard kselftest run.
With udp, msg_zerocopy has no control channel. Ensure that the
receiver exits after the sender by accounting for the initial
delay in starting them (in msg_zerocopy.sh).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This script tests the support of a VXLAN underlay in a non-default VRF.
It does so by simulating two hypervisors and two VMs, an extended L2
between the VMs with the hypervisors as VTEPs with the underlay in a
VRF, and finally by pinging the two VMs.
It also tests that moving the underlay from a VRF to another works when
down/up the VXLAN interface.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test is very similar to its VLAN-unaware counterpart
(vxlan_bridge_1d.sh), but instead of using multiple VLAN-unaware
bridges, a single VLAN-aware bridge is used with multiple VLANs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the existing VLAN-unaware tests with their VLAN-aware
counterparts. This includes sanitization of invalid configuration and
offload indication on the local route performing decapsulation and the
FDB entries perform encapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous patches add the ability to work with VLAN-aware bridges and
VxLAN devices, so make sure such configuration no longer fails.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
bpf-next 2018-11-30
The following pull-request contains BPF updates for your *net-next* tree.
(Getting out bit earlier this time to pull in a dependency from bpf.)
The main changes are:
1) Add libbpf ABI versioning and document API naming conventions
as well as ABI versioning process, from Andrey.
2) Add a new sk_msg_pop_data() helper for sk_msg based BPF
programs that is used in conjunction with sk_msg_push_data()
for adding / removing meta data to the msg data, from John.
3) Optimize convert_bpf_ld_abs() for 0 offset and fix various
lib and testsuite build failures on 32 bit, from David.
4) Make BPF prog dump for !JIT identical to how we dump subprogs
when JIT is in use, from Yonghong.
5) Rename btf_get_from_id() to make it more conform with libbpf
API naming conventions, from Martin.
6) Add a missing BPF kselftest config item, from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During porting libbpf to bcc, I got some warnings like below:
...
[ 2%] Building C object src/cc/CMakeFiles/bpf-shared.dir/libbpf/src/libbpf.c.o
/home/yhs/work/bcc2/src/cc/libbpf/src/libbpf.c:12:0:
warning: "_GNU_SOURCE" redefined [enabled by default]
#define _GNU_SOURCE
...
[ 3%] Building C object src/cc/CMakeFiles/bpf-shared.dir/libbpf/src/libbpf_errno.c.o
/home/yhs/work/bcc2/src/cc/libbpf/src/libbpf_errno.c: In function ‘libbpf_strerror’:
/home/yhs/work/bcc2/src/cc/libbpf/src/libbpf_errno.c:45:7:
warning: assignment makes integer from pointer without a cast [enabled by default]
ret = strerror_r(err, buf, size);
...
bcc is built with _GNU_SOURCE defined and this caused the above warning.
This patch intends to make libpf _GNU_SOURCE friendly by
. define _GNU_SOURCE in libbpf.c unless it is not defined
. undefine _GNU_SOURCE as non-gnu version of strerror_r is expected.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cannot cast a u64 to a pointer on 32-bit without an intervening (long)
cast otherwise GCC warns.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
CONFIG_FTRACE_SYSCALLS=y is required for get_cgroup_id_user test case
this test reads a file from debug trace path
/sys/kernel/debug/tracing/events/syscalls/sys_enter_nanosleep/id
Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Similar to msg_pull_data and msg_push_data add a set of options to
have msg_pop_data() exercised.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Add the necessary header definitions to tools for new
msg_pop_data_helper.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Disable BH while holding list spinlock in nf_conncount, from
Taehee Yoo.
2) List corruption in nf_conncount, also from Taehee.
3) Fix race that results in leaving around an empty list node in
nf_conncount, from Taehee Yoo.
4) Proper chain handling for inactive chains from the commit path,
from Florian Westphal. This includes a selftest for this.
5) Do duplicate rule handles when replacing rules, also from Florian.
6) Remove net_exit path in xt_RATEEST that results in splat, from Taehee.
7) Possible use-after-free in nft_compat when releasing extensions.
From Florian.
8) Memory leak in xt_hashlimit, from Taehee.
9) Call ip_vs_dst_notifier after ipv6_dev_notf, from Xin Long.
10) Fix cttimeout with udplite and gre, from Florian.
11) Preserve oif for IPv6 link-local generated traffic from mangle
table, from Alin Nastac.
12) Missing error handling in masquerade notifiers, from Taehee Yoo.
13) Use mutex to protect registration/unregistration of masquerade
extensions in order to prevent a race, from Taehee.
14) Incorrect condition check in tree_nodes_free(), also from Taehee.
15) Fix chain counter leak in rule replacement path, from Taehee.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document API and ABI for libbpf: naming convention, symbol visibility,
ABI versioning.
This is just a starting point. Documentation can be significantly
extended in the future to cover more topics.
ABI versioning section touches only a few basic points with a link to
more comprehensive documentation from Ulrich Drepper. This section can
be extended in the future when there is better understanding what works
well and what not so well in libbpf development process and production
usage.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Since ABI versioning info is kept separately from the code it's easy to
forget to update it while adding a new API.
Add simple verification that all global symbols exported with LIBBPF_API
are versioned in libbpf.map version script.
The idea is to check that number of global symbols in libbpf-in.o, that
is the input to the linker, matches with number of unique versioned
symbols in libbpf.so, that is the output of the linker. If these numbers
don't match, it may mean some symbol was not versioned and make will
fail.
"Unique" means that if a symbol is present in more than one version of
ABI due to ABI changes, it'll be counted once.
Another option to calculate number of global symbols in the "input"
could be to count number of LIBBPF_ABI entries in C headers but it seems
to be fragile.
Example of output when a symbol is missing in version script:
...
LD libbpf-in.o
LINK libbpf.a
LINK libbpf.so
Warning: Num of global symbols in libbpf-in.o (115) does NOT match
with num of versioned symbols in libbpf.so (114). Please make sure all
LIBBPF_API symbols are versioned in libbpf.map.
make: *** [check_abi] Error 1
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
More and more projects use libbpf and one day it'll likely be packaged
and distributed as DSO and that requires ABI versioning so that both
compatible and incompatible changes to ABI can be introduced in a safe
way in the future without breaking executables dynamically linked with a
previous version of the library.
Usual way to do ABI versioning is version script for the linker. Add
such a script for libbpf. All global symbols currently exported via
LIBBPF_API macro are added to the version script libbpf.map.
The version name LIBBPF_0.0.1 is constructed from the name of the
library + version specified by $(LIBBPF_VERSION) in Makefile.
Version script does not duplicate the work done by LIBBPF_API macro, it
rather complements it. The macro is used at compile time and can be used
by compiler to do optimization that can't be done at link time, it is
purely about global symbol visibility. The version script, in turn, is
used at link time and takes care of ABI versioning. Both techniques are
described in details in [1].
Whenever ABI is changed in the future, version script should be changed
appropriately.
[1] https://www.akkadia.org/drepper/dsohowto.pdf
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
s/btf_get_from_id/btf__get_from_id/ to restore the API naming convention.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The selftest test_btf is changed to test both jit and non-jit.
The test result should be the same regardless of whether jit
is enabled or not.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-11-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Extend BTF to support function call types and improve the BPF
symbol handling with this info for kallsyms and bpftool program
dump to make debugging easier, from Martin and Yonghong.
2) Optimize LPM lookups by making longest_prefix_match() handle
multiple bytes at a time, from Eric.
3) Adds support for loading and attaching flow dissector BPF progs
from bpftool, from Stanislav.
4) Extend the sk_lookup() helper to be supported from XDP, from Nitin.
5) Enable verifier to support narrow context loads with offset > 0
to adapt to LLVM code generation (currently only offset of 0 was
supported). Add test cases as well, from Andrey.
6) Simplify passing device functions for offloaded BPF progs by
adding callbacks to bpf_prog_offload_ops instead of ndo_bpf.
Also convert nfp and netdevsim to make use of them, from Quentin.
7) Add support for sock_ops based BPF programs to send events to
the perf ring-buffer through perf_event_output helper, from
Sowmini and Daniel.
8) Add read / write support for skb->tstamp from tc BPF and cg BPF
programs to allow for supporting rate-limiting in EDT qdiscs
like fq from BPF side, from Vlad.
9) Extend libbpf API to support map in map types and add test cases
for it as well to BPF kselftests, from Nikita.
10) Account the maximum packet offset accessed by a BPF program in
the verifier and use it for optimizing nfp JIT, from Jiong.
11) Fix error handling regarding kprobe_events in BPF sample loader,
from Daniel T.
12) Add support for queue and stack map type in bpftool, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-11-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix an off-by-one bug when adjusting subprog start offsets after
patching, from Edward.
2) Fix several bugs such as overflow in size allocation in queue /
stack map creation, from Alexei.
3) Fix wrong IPv6 destination port byte order in bpf_sk_lookup_udp
helper, from Andrey.
4) Fix several bugs in bpftool such as preventing an infinite loop
in get_fdinfo, error handling and man page references, from Quentin.
5) Fix a warning in bpf_trace_printk() that wasn't catching an
invalid format string, from Martynas.
6) Fix a bug in BPF cgroup local storage where non-atomic allocation
was used in atomic context, from Roman.
7) Fix a NULL pointer dereference bug in bpftool from reallocarray()
error handling, from Jakub and Wen.
8) Add a copy of pkt_cls.h and tc_bpf.h uapi headers to the tools
include infrastructure so that bpftool compiles on older RHEL7-like
user space which does not ship these headers, from Yonghong.
9) Fix BPF kselftests for user space where to get ping test working
with ping6 and ping -6, from Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the formatting for map_type_name array consistent.
Signed-off-by: David Calavera <david.calavera@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Packet sockets with PACKET_TX_RING send skbs with user data in frags.
Before commit 5cd8d46ea156 ("packet: copy user buffers before orphan
or clone") ring slots could be released prematurely, possibly allowing
a process to overwrite data still in flight.
This test opens two packet sockets, one to send and one to read.
The sender has a tx ring of one slot. It sends two packets with
different payload, then reads both and verifies their payload.
Before the above commit, both receive calls return the same data as
the send calls use the same buffer. From the commit, the clone
needed for looping onto a packet socket triggers an skb_copy_ubufs
to create a private copy. The separate sends each arrive correctly.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
I noticed that these two new BPF Maps are not defined in bpftool.
This patch defines those two maps and adds their names to the
bpftool-map documentation.
Signed-off-by: David Calavera <david.calavera@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
currently by default libbpf's bpf_object__open requires
bpf's program to specify version in a code because of two things:
1) default prog type is set to KPROBE
2) KPROBE requires (in kernel/bpf/syscall.c) version to be specified
in this patch i'm changing default prog type to UNSPEC and also changing
requirments for version's section to be present in object file.
now it would reflect what we have today in kernel
(only KPROBE prog type requires for version to be explicitly set).
v1 -> v2:
- RFC tag has been dropped
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pull power management fixes from Rafael Wysocki:
"These fix two issues in the Operating Performance Points (OPP)
framework, one cpufreq driver issue, one problem related to the tasks
freezer and a few build-related issues in the cpupower utility.
Specifics:
- Fix tasks freezer deadlock in de_thread() that occurs if one of its
sub-threads has been frozen already (Chanho Min).
- Avoid registering a platform device by the ti-cpufreq driver on
platforms that cannot use it (Dave Gerlach).
- Fix a mistake in the ti-opp-supply operating performance points
(OPP) driver that caused an incorrect reference voltage to be used
and make it adjust the minimum voltage dynamically to avoid hangs
or crashes in some cases (Keerthy).
- Fix issues related to compiler flags in the cpupower utility and
correct a linking problem in it by renaming a file with a duplicate
name (Jiri Olsa, Konstantin Khlebnikov)"
* tag 'pm-4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
exec: make de_thread() freezable
cpufreq: ti-cpufreq: Only register platform_device when supported
opp: ti-opp-supply: Correct the supply in _get_optimal_vdd_voltage call
opp: ti-opp-supply: Dynamically update u_volt_min
tools cpupower: Override CFLAGS assignments
tools cpupower debug: Allow to use outside build flags
tools/power/cpupower: fix compilation with STATIC=true
|
|
This could be used to rate limit egress traffic in concert with a qdisc
which supports Earliest Departure Time, such as FQ.
Write access from cg skb progs only with CAP_SYS_ADMIN, since the value
will be used by downstream qdiscs. It might make sense to relax this.
Changes v1 -> v2:
- allow access from cg skb, write only with CAP_SYS_ADMIN
Signed-off-by: Vlad Dumitrescu <vladum@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
commit 3327a9c46352f1 ("selftests: add functionals test for UDP GRO")
make use of ipv6 NAT, but such a feature is not currently implied by
selftests. Since the 'ip[6]tables' commands may actually create nft rules,
depending on the specific user-space version, let's pull both NF and
NFT nat modules plus the needed deps.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 3327a9c46352f1 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CHECK message contains a spelling mistake, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Add a test which checks that the VxLAN driver can learn FDB entries and
that these entries are correctly deleted and aged-out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test currently expects that a configuration which includes a VxLAN
device with learning enabled to fail.
Previous patches enabled VxLAN learning in mlxsw, so change the test
accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a possible null pointer dereference in
do_load, detected by the semantic patch deref_null.cocci,
with the following warning:
./tools/bpf/bpftool/prog.c:1021:23-25: ERROR: map_replace is NULL but dereferenced.
The following code has potential null pointer references:
881 map_replace = reallocarray(map_replace, old_map_fds + 1,
882 sizeof(*map_replace));
883 if (!map_replace) {
884 p_err("mem alloc failed");
885 goto err_free_reuse_maps;
886 }
...
1019 err_free_reuse_maps:
1020 for (i = 0; i < old_map_fds; i++)
1021 close(map_replace[i].fd);
1022 free(map_replace);
Fixes: 3ff5a4dc5d89 ("tools: bpftool: allow reuse of maps with bpftool prog load")
Co-developed-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
adding test/example of bpf_map__set_inner_map_fd usage
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
idea is pretty simple. for specified map (pointed by struct bpf_map)
we would provide descriptor of already loaded map, which is going to be
used as a prototype for inner map. proposed workflow:
1) open bpf's object (bpf_object__open)
2) create bpf's map which is going to be used as a prototype
3) find (by name) map-in-map which you want to load and update w/
descriptor of inner map w/ a new helper from this patch
4) load bpf program w/ bpf_object__load
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Use recently added capability check.
See commit 23499442c319 ("bpf: libbpf: retry map creation without
the name") for rationale.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Instead, check for a newly created caps.name bpf_object capability.
If kernel doesn't support names, don't specify the attribute.
See commit 23499442c319 ("bpf: libbpf: retry map creation without
the name") for rationale.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
It currently only checks whether kernel supports map/prog names.
This capability check will be used in the next two commits to
skip setting prog/map names.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Wrap headers in extern "C", to turn off C++ mangling.
This simplifies including libbpf in c++ and linking against it.
v2 changes:
* do the same for btf.h
v3 changes:
* test_libbpf.cpp to test for possible future c++ breakages
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Commit 2993e0515bb4 ("tools/bpf: add support to read .BTF.ext sections")
added support to read .BTF.ext sections from an object file, create
and pass prog_btf_fd and func_info to the kernel.
The program btf_fd (prog->btf_fd) is initialized to be -1 to please
zclose so we do not need special handling dur prog close.
Passing -1 to the kernel, however, will cause loading error.
Passing btf_fd 0 to the kernel if prog->btf_fd is invalid
fixed the problem.
Fixes: 2993e0515bb4 ("tools/bpf: add support to read .BTF.ext sections")
Reported-by: Andrey Ignatov <rdna@fb.com>
Reported-by: Emre Cantimur <haydum@fb.com>
Tested-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pull cpupower utility updates for 4.20-rc4 from Shuah Khan:
"This cpupower update for Linux 4.20-rc4 consists of compile fixes to allow
use of outside build flags and override of CFLAGS from Jiri Olsa, and fix
to compilation with STATIC=true from Konstantin Khlebnikov."
* tag 'linux-cpupower-4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
tools cpupower: Override CFLAGS assignments
tools cpupower debug: Allow to use outside build flags
tools/power/cpupower: fix compilation with STATIC=true
|
|
This patch added support to print function signature
if btf func_info is available. Note that ksym
now uses function name instead of prog_name as
prog_name has a limit of 16 bytes including
ending '\0'.
The following is a sample output for selftests
test_btf with file test_btf_haskv.o for translated insns
and jited insns respectively.
$ bpftool prog dump xlated id 1
int _dummy_tracepoint(struct dummy_tracepoint_args * arg):
0: (85) call pc+2#bpf_prog_2dcecc18072623fc_test_long_fname_1
1: (b7) r0 = 0
2: (95) exit
int test_long_fname_1(struct dummy_tracepoint_args * arg):
3: (85) call pc+1#bpf_prog_89d64e4abf0f0126_test_long_fname_2
4: (95) exit
int test_long_fname_2(struct dummy_tracepoint_args * arg):
5: (b7) r2 = 0
6: (63) *(u32 *)(r10 -4) = r2
7: (79) r1 = *(u64 *)(r1 +8)
...
22: (07) r1 += 1
23: (63) *(u32 *)(r0 +4) = r1
24: (95) exit
$ bpftool prog dump jited id 1
int _dummy_tracepoint(struct dummy_tracepoint_args * arg):
bpf_prog_b07ccb89267cf242__dummy_tracepoint:
0: push %rbp
1: mov %rsp,%rbp
......
3c: add $0x28,%rbp
40: leaveq
41: retq
int test_long_fname_1(struct dummy_tracepoint_args * arg):
bpf_prog_2dcecc18072623fc_test_long_fname_1:
0: push %rbp
1: mov %rsp,%rbp
......
3a: add $0x28,%rbp
3e: leaveq
3f: retq
int test_long_fname_2(struct dummy_tracepoint_args * arg):
bpf_prog_89d64e4abf0f0126_test_long_fname_2:
0: push %rbp
1: mov %rsp,%rbp
......
80: add $0x28,%rbp
84: leaveq
85: retq
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Change the bpf programs test_btf_haskv.c and test_btf_nokv.c to
have two sections, and enhance test_btf.c test_file feature
to test btf func_info returned by the kernel.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The function get_btf() is implemented in tools/bpf/bpftool/map.c
to get a btf structure given a map_info. This patch
refactored this function to be function btf_get_from_id()
in tools/lib/bpf so that it can be used later.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add additional checks in tools/testing/selftests/bpf and
samples/bpf such that if clang/llvm compiler can generate
BTF sections, do not use pahole.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The .BTF section is already available to encode types.
These types can be used for map
pretty print. The whole .BTF will be passed to the
kernel as well for which kernel can verify and return
to the user space for pretty print etc.
The llvm patch at https://reviews.llvm.org/D53736
will generate .BTF section and one more section .BTF.ext.
The .BTF.ext section encodes function type
information and line information. Note that
this patch set only supports function type info.
The functionality is implemented in libbpf.
The .BTF section can be directly loaded into the
kernel, and the .BTF.ext section cannot. The loader
may need to do some relocation and merging,
similar to merging multiple code sections, before
loading into the kernel.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
A two function bpf program is loaded with btf and func_info.
After successful prog load, the bpf_get_info syscall is called
to retrieve prog info to ensure the types returned from the
kernel matches the types passed to the kernel from the
user space.
Several negative tests are also added to test loading/retriving
of func_type info.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The new fields are added for program load in lib/bpf so
application uses api bpf_load_program_xattr() is able
to load program with btf and func_info data.
This functionality will be used in next patch
by bpf selftest test_btf.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The kernel uapi bpf.h is synced to tools directory.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch adds unit tests for BTF_KIND_FUNC_PROTO and
BTF_KIND_FUNC to test_btf.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
Ido Schimmel
Willem de Bruijn
Alexis Bauvin
David S. Miller
Yonghong Song
Naresh Kamboju
John Fastabend
Andrey Ignatov
Martin KaFai Lau
David Calavera
Nikita V. Shirokov
Linus Torvalds
Vlad Dumitrescu
Paolo Abeni
Colin Ian King
Jakub Kicinski
Stanislav Fomichev
Rafael J. Wysocki