From ddc25bdd2b7f34667111714fafc9c04f6ad97fee Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Wed, 7 Jan 2015 13:15:22 +0100 Subject: iio: dht11: Fix out-of-bounds read As we access i-1 we must not start with i=0. Signed-off-by: Richard Weinberger Acked-by: Hartmut Knaack Acked-by: Harald Geyer Reviewed-by: Sanjeev Sharma Signed-off-by: Jonathan Cameron --- drivers/iio/humidity/dht11.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/iio/humidity/dht11.c b/drivers/iio/humidity/dht11.c index 623c145d8a97..f546ecae90f1 100644 --- a/drivers/iio/humidity/dht11.c +++ b/drivers/iio/humidity/dht11.c @@ -88,7 +88,7 @@ static int dht11_decode(struct dht11 *dht11, int offset) unsigned char temp_int, temp_dec, hum_int, hum_dec, checksum; /* Calculate timestamp resolution */ - for (i = 0; i < dht11->num_edges; ++i) { + for (i = 1; i < dht11->num_edges; ++i) { t = dht11->edges[i].ts - dht11->edges[i-1].ts; if (t > 0 && t < timeres) timeres = t; -- cgit v1.2.3-59-g8ed1b From 004bc530341a40536494431cf665504f8ee70266 Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Wed, 7 Jan 2015 13:18:23 +0100 Subject: iio: dht11: Add locking Make sure that the read function is not interrupted... Signed-off-by: Richard Weinberger Acked-by: Harald Geyer Reviewed-by: Sanjeev Sharma Signed-off-by: Jonathan Cameron --- drivers/iio/humidity/dht11.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/iio/humidity/dht11.c b/drivers/iio/humidity/dht11.c index f546ecae90f1..7717f5c3395b 100644 --- a/drivers/iio/humidity/dht11.c +++ b/drivers/iio/humidity/dht11.c @@ -29,6 +29,7 @@ #include #include #include +#include #include #include #include @@ -57,6 +58,7 @@ struct dht11 { int irq; struct completion completion; + struct mutex lock; s64 timestamp; int temperature; @@ -145,6 +147,7 @@ static int dht11_read_raw(struct iio_dev *iio_dev, struct dht11 *dht11 = iio_priv(iio_dev); int ret; + mutex_lock(&dht11->lock); if (dht11->timestamp + DHT11_DATA_VALID_TIME < iio_get_time_ns()) { reinit_completion(&dht11->completion); @@ -185,6 +188,7 @@ static int dht11_read_raw(struct iio_dev *iio_dev, ret = -EINVAL; err: dht11->num_edges = -1; + mutex_unlock(&dht11->lock); return ret; } @@ -268,6 +272,7 @@ static int dht11_probe(struct platform_device *pdev) platform_set_drvdata(pdev, iio); init_completion(&dht11->completion); + mutex_init(&dht11->lock); iio->name = pdev->name; iio->dev.parent = &pdev->dev; iio->info = &dht11_iio_info; -- cgit v1.2.3-59-g8ed1b From 94e65519abde01cbffb9c538a4598f6a50bc86d1 Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Wed, 7 Jan 2015 13:22:49 +0100 Subject: iio: dht11: IRQ fixes Since setting irq-enabled GPIOs into output state is not supported by all GPIO controllers, we need to disable the irq while requesting sensor data. As side effect we lose a tiny bit of functionality: Some wiring problems can't be concluded from log messages anymore. Signed-off-by: Richard Weinberger Signed-off-by: Harald Geyer Signed-off-by: Jonathan Cameron --- drivers/iio/humidity/dht11.c | 62 +++++++++++++++++++++++++------------------- 1 file changed, 35 insertions(+), 27 deletions(-) diff --git a/drivers/iio/humidity/dht11.c b/drivers/iio/humidity/dht11.c index 7717f5c3395b..7d79a1ac5f5f 100644 --- a/drivers/iio/humidity/dht11.c +++ b/drivers/iio/humidity/dht11.c @@ -40,8 +40,12 @@ #define DHT11_DATA_VALID_TIME 2000000000 /* 2s in ns */ -#define DHT11_EDGES_PREAMBLE 4 +#define DHT11_EDGES_PREAMBLE 2 #define DHT11_BITS_PER_READ 40 +/* + * Note that when reading the sensor actually 84 edges are detected, but + * since the last edge is not significant, we only store 83: + */ #define DHT11_EDGES_PER_READ (2*DHT11_BITS_PER_READ + DHT11_EDGES_PREAMBLE + 1) /* Data transmission timing (nano seconds) */ @@ -140,6 +144,27 @@ static int dht11_decode(struct dht11 *dht11, int offset) return 0; } +/* + * IRQ handler called on GPIO edges + */ +static irqreturn_t dht11_handle_irq(int irq, void *data) +{ + struct iio_dev *iio = data; + struct dht11 *dht11 = iio_priv(iio); + + /* TODO: Consider making the handler safe for IRQ sharing */ + if (dht11->num_edges < DHT11_EDGES_PER_READ && dht11->num_edges >= 0) { + dht11->edges[dht11->num_edges].ts = iio_get_time_ns(); + dht11->edges[dht11->num_edges++].value = + gpio_get_value(dht11->gpio); + + if (dht11->num_edges >= DHT11_EDGES_PER_READ) + complete(&dht11->completion); + } + + return IRQ_HANDLED; +} + static int dht11_read_raw(struct iio_dev *iio_dev, const struct iio_chan_spec *chan, int *val, int *val2, long m) @@ -160,8 +185,17 @@ static int dht11_read_raw(struct iio_dev *iio_dev, if (ret) goto err; + ret = request_irq(dht11->irq, dht11_handle_irq, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + iio_dev->name, iio_dev); + if (ret) + goto err; + ret = wait_for_completion_killable_timeout(&dht11->completion, HZ); + + free_irq(dht11->irq, iio_dev); + if (ret == 0 && dht11->num_edges < DHT11_EDGES_PER_READ - 1) { dev_err(&iio_dev->dev, "Only %d signal edges detected\n", @@ -197,27 +231,6 @@ static const struct iio_info dht11_iio_info = { .read_raw = dht11_read_raw, }; -/* - * IRQ handler called on GPIO edges -*/ -static irqreturn_t dht11_handle_irq(int irq, void *data) -{ - struct iio_dev *iio = data; - struct dht11 *dht11 = iio_priv(iio); - - /* TODO: Consider making the handler safe for IRQ sharing */ - if (dht11->num_edges < DHT11_EDGES_PER_READ && dht11->num_edges >= 0) { - dht11->edges[dht11->num_edges].ts = iio_get_time_ns(); - dht11->edges[dht11->num_edges++].value = - gpio_get_value(dht11->gpio); - - if (dht11->num_edges >= DHT11_EDGES_PER_READ) - complete(&dht11->completion); - } - - return IRQ_HANDLED; -} - static const struct iio_chan_spec dht11_chan_spec[] = { { .type = IIO_TEMP, .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), }, @@ -260,11 +273,6 @@ static int dht11_probe(struct platform_device *pdev) dev_err(dev, "GPIO %d has no interrupt\n", dht11->gpio); return -EINVAL; } - ret = devm_request_irq(dev, dht11->irq, dht11_handle_irq, - IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, - pdev->name, iio); - if (ret) - return ret; dht11->timestamp = iio_get_time_ns() - DHT11_DATA_VALID_TIME - 1; dht11->num_edges = -1; -- cgit v1.2.3-59-g8ed1b From f2229ab8611e6e79992b6357db3fb4faf70e74a9 Mon Sep 17 00:00:00 2001 From: Nicholas Mc Guire Date: Wed, 31 Dec 2014 03:59:46 -0500 Subject: iio: iadc: wait_for_completion_timeout time in jiffies The timeout value to wait_for_completion_timeout is in jiffies but the value being passed seems like it was intended to by microseconds Note that the timeout was extremely long thus it might be too short now. In any case it probably should be passed through usecs_to_jiffies() or msecs_to_jiffies() patch is against linux-next 3.19.0-rc1 -next-20141226 patch was only compile-tested x86_64_defcofnig + CONFIG_SPMI=m CONFIG_IIO=m, CONFIG_QCOM_SPMI_IADC=m Signed-off-by: Nicholas Mc Guire Acked-by: Ivan T. Ivanov Signed-off-by: Jonathan Cameron --- drivers/iio/adc/qcom-spmi-iadc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/iio/adc/qcom-spmi-iadc.c b/drivers/iio/adc/qcom-spmi-iadc.c index b9666f2f5e51..fabd24edc2a1 100644 --- a/drivers/iio/adc/qcom-spmi-iadc.c +++ b/drivers/iio/adc/qcom-spmi-iadc.c @@ -296,7 +296,8 @@ static int iadc_do_conversion(struct iadc_chip *iadc, int chan, u16 *data) if (iadc->poll_eoc) { ret = iadc_poll_wait_eoc(iadc, wait); } else { - ret = wait_for_completion_timeout(&iadc->complete, wait); + ret = wait_for_completion_timeout(&iadc->complete, + usecs_to_jiffies(wait)); if (!ret) ret = -ETIMEDOUT; else -- cgit v1.2.3-59-g8ed1b From 4f33fbae555000bf73aaacbc4f5b24668afc8c7a Mon Sep 17 00:00:00 2001 From: Srinivas Pandruvada Date: Fri, 9 Jan 2015 15:13:37 -0800 Subject: iio: imu: inv_mpu6050: Prevent dereferencing NULL When id is null, with ACPI enumeration, don't dereference it. Signed-off-by: Srinivas Pandruvada Signed-off-by: Jonathan Cameron --- drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c index b75519deac1a..eedd3e07d27c 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c @@ -690,7 +690,11 @@ static int inv_mpu_probe(struct i2c_client *client, i2c_set_clientdata(client, indio_dev); indio_dev->dev.parent = &client->dev; - indio_dev->name = id->name; + /* id will be NULL when enumerated via ACPI */ + if (id) + indio_dev->name = (char *)id->name; + else + indio_dev->name = (char *)dev_name(&client->dev); indio_dev->channels = inv_mpu_channels; indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels); -- cgit v1.2.3-59-g8ed1b From fb8b7d2b9d80e1e71f379e57355936bd2b024be9 Mon Sep 17 00:00:00 2001 From: Jammy Zhou Date: Wed, 21 Jan 2015 18:35:47 +0800 Subject: reservation: wait only with non-zero timeout specified (v3) MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When the timeout value passed to reservation_object_wait_timeout_rcu is zero, no wait should be done if the fences are not signaled. Return '1' for idle and '0' for busy if the specified timeout is '0' to keep consistent with the case of non-zero timeout. v2: call fence_put if not signaled in the case of timeout==0 v3: switch to reservation_object_test_signaled_rcu Signed-off-by: Jammy Zhou Reviewed-by: Christian König Reviewed-by: Alex Deucher Reviewed-By: Maarten Lankhorst Signed-off-by: Sumit Semwal --- drivers/dma-buf/reservation.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/dma-buf/reservation.c b/drivers/dma-buf/reservation.c index 3c97c8fa8d02..807ef1555255 100644 --- a/drivers/dma-buf/reservation.c +++ b/drivers/dma-buf/reservation.c @@ -327,6 +327,9 @@ long reservation_object_wait_timeout_rcu(struct reservation_object *obj, unsigned seq, shared_count, i = 0; long ret = timeout; + if (!timeout) + return reservation_object_test_signaled_rcu(obj, wait_all); + retry: fence = NULL; shared_count = 0; -- cgit v1.2.3-59-g8ed1b From 847b19a39e4c9b5e74c40f0842c48b41664cb43c Mon Sep 17 00:00:00 2001 From: Jammy Zhou Date: Wed, 21 Jan 2015 18:35:48 +0800 Subject: dma-buf/fence: don't wait when specified timeout is zero MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When specified timeout is zero for fence_wait_timeout, just check if the fence is signaled or not without wait. Signed-off-by: Jammy Zhou Reviewed-by: Christian König Reviewed-By: Maarten Lankhorst Signed-off-by: Sumit Semwal --- drivers/dma-buf/fence.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/dma-buf/fence.c b/drivers/dma-buf/fence.c index e5541117b3e9..50ef8bd8708b 100644 --- a/drivers/dma-buf/fence.c +++ b/drivers/dma-buf/fence.c @@ -159,6 +159,9 @@ fence_wait_timeout(struct fence *fence, bool intr, signed long timeout) if (WARN_ON(timeout < 0)) return -EINVAL; + if (timeout == 0) + return fence_is_signaled(fence); + trace_fence_wait_start(fence); ret = fence->ops->wait(fence, intr, timeout); trace_fence_wait_end(fence); -- cgit v1.2.3-59-g8ed1b From 4eb2440ed60fb5793f7aa6da89b3d517cc59de43 Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Thu, 22 Jan 2015 16:00:17 +0900 Subject: reservation: Remove shadowing local variable 'ret' MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It was causing the return value of fence_is_signaled to be ignored, making reservation objects signal too early. Cc: stable@vger.kernel.org Reviewed-by: Maarten Lankhorst Reviewed-by: Alex Deucher Signed-off-by: Michel Dänzer Signed-off-by: Sumit Semwal --- drivers/dma-buf/reservation.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/dma-buf/reservation.c b/drivers/dma-buf/reservation.c index 807ef1555255..39920d77f288 100644 --- a/drivers/dma-buf/reservation.c +++ b/drivers/dma-buf/reservation.c @@ -405,8 +405,6 @@ reservation_object_test_signaled_single(struct fence *passed_fence) int ret = 1; if (!test_bit(FENCE_FLAG_SIGNALED_BIT, &lfence->flags)) { - int ret; - fence = fence_get_rcu(lfence); if (!fence) return -1; -- cgit v1.2.3-59-g8ed1b From f81197b8a31b8fb287ae57f597b5b6841e1ece92 Mon Sep 17 00:00:00 2001 From: Kristina Martšenko Date: Sun, 25 Jan 2015 18:28:19 +0200 Subject: iio: mxs-lradc: separate touchscreen and buffer virtual channels MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The touchscreen was initially designed [1] to map all of its physical channels to one virtual channel, leaving buffered capture to use the remaining 7 virtual channels. When the touchscreen was reimplemented [2], it was made to use four virtual channels, which overlap and conflict with the channels the buffer uses. As a result, when the buffer is enabled, the touchscreen's virtual channels are remapped to whichever physical channels the buffer was configured with, causing the touchscreen to read those instead of the touch measurement channels. Effectively the touchscreen stops working. So here we separate the channels again, giving the touchscreen 2 virtual channels and the buffer 6. We can't give the touchscreen just 1 channel as before, as the current pressure calculation requires 2 channels to be read at the same time. This makes the touchscreen continue to work during buffered capture. It has been tested on i.MX28, but not on i.MX23. [1] 06ddd353f5c8 ("iio: mxs: Implement support for touchscreen") [2] dee05308f602 ("Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection") Signed-off-by: Kristina Martšenko Reviewed-by: Marek Vasut Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/staging/iio/adc/mxs-lradc.c | 166 ++++++++++++++++-------------------- 1 file changed, 75 insertions(+), 91 deletions(-) diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c index f053535385bf..4e574b76ead0 100644 --- a/drivers/staging/iio/adc/mxs-lradc.c +++ b/drivers/staging/iio/adc/mxs-lradc.c @@ -214,11 +214,14 @@ struct mxs_lradc { unsigned long is_divided; /* - * Touchscreen LRADC channels receives a private slot in the CTRL4 - * register, the slot #7. Therefore only 7 slots instead of 8 in the - * CTRL4 register can be mapped to LRADC channels when using the - * touchscreen. - * + * When the touchscreen is enabled, we give it two private virtual + * channels: #6 and #7. This means that only 6 virtual channels (instead + * of 8) will be available for buffered capture. + */ +#define TOUCHSCREEN_VCHANNEL1 7 +#define TOUCHSCREEN_VCHANNEL2 6 + + /* * Furthermore, certain LRADC channels are shared between touchscreen * and/or touch-buttons and generic LRADC block. Therefore when using * either of these, these channels are not available for the regular @@ -342,6 +345,9 @@ struct mxs_lradc { #define LRADC_CTRL4 0x140 #define LRADC_CTRL4_LRADCSELECT_MASK(n) (0xf << ((n) * 4)) #define LRADC_CTRL4_LRADCSELECT_OFFSET(n) ((n) * 4) +#define LRADC_CTRL4_LRADCSELECT(n, x) \ + (((x) << LRADC_CTRL4_LRADCSELECT_OFFSET(n)) & \ + LRADC_CTRL4_LRADCSELECT_MASK(n)) #define LRADC_RESOLUTION 12 #define LRADC_SINGLE_SAMPLE_MASK ((1 << LRADC_RESOLUTION) - 1) @@ -416,6 +422,14 @@ static bool mxs_lradc_check_touch_event(struct mxs_lradc *lradc) LRADC_STATUS_TOUCH_DETECT_RAW); } +static void mxs_lradc_map_channel(struct mxs_lradc *lradc, unsigned vch, + unsigned ch) +{ + mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(vch), + LRADC_CTRL4); + mxs_lradc_reg_set(lradc, LRADC_CTRL4_LRADCSELECT(vch, ch), LRADC_CTRL4); +} + static void mxs_lradc_setup_ts_channel(struct mxs_lradc *lradc, unsigned ch) { /* @@ -443,12 +457,8 @@ static void mxs_lradc_setup_ts_channel(struct mxs_lradc *lradc, unsigned ch) LRADC_DELAY_DELAY(lradc->over_sample_delay - 1), LRADC_DELAY(3)); - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) | - LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) | - LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1); + mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(ch), LRADC_CTRL1); - /* wake us again, when the complete conversion is done */ - mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch), LRADC_CTRL1); /* * after changing the touchscreen plates setting * the signals need some initial time to settle. Start the @@ -502,12 +512,8 @@ static void mxs_lradc_setup_ts_pressure(struct mxs_lradc *lradc, unsigned ch1, LRADC_DELAY_DELAY(lradc->over_sample_delay - 1), LRADC_DELAY(3)); - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) | - LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) | - LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1); + mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(ch2), LRADC_CTRL1); - /* wake us again, when the conversions are done */ - mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch2), LRADC_CTRL1); /* * after changing the touchscreen plates setting * the signals need some initial time to settle. Start the @@ -573,36 +579,6 @@ static unsigned mxs_lradc_read_ts_pressure(struct mxs_lradc *lradc, #define TS_CH_XM 4 #define TS_CH_YM 5 -static int mxs_lradc_read_ts_channel(struct mxs_lradc *lradc) -{ - u32 reg; - int val; - - reg = readl(lradc->base + LRADC_CTRL1); - - /* only channels 3 to 5 are of interest here */ - if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YP)) { - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YP) | - LRADC_CTRL1_LRADC_IRQ(TS_CH_YP), LRADC_CTRL1); - val = mxs_lradc_read_raw_channel(lradc, TS_CH_YP); - } else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_XM)) { - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_XM) | - LRADC_CTRL1_LRADC_IRQ(TS_CH_XM), LRADC_CTRL1); - val = mxs_lradc_read_raw_channel(lradc, TS_CH_XM); - } else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YM)) { - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YM) | - LRADC_CTRL1_LRADC_IRQ(TS_CH_YM), LRADC_CTRL1); - val = mxs_lradc_read_raw_channel(lradc, TS_CH_YM); - } else { - return -EIO; - } - - mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2)); - mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3)); - - return val; -} - /* * YP(open)--+-------------+ * | |--+ @@ -646,7 +622,8 @@ static void mxs_lradc_prepare_x_pos(struct mxs_lradc *lradc) mxs_lradc_reg_set(lradc, mxs_lradc_drive_x_plate(lradc), LRADC_CTRL0); lradc->cur_plate = LRADC_SAMPLE_X; - mxs_lradc_setup_ts_channel(lradc, TS_CH_YP); + mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL1, TS_CH_YP); + mxs_lradc_setup_ts_channel(lradc, TOUCHSCREEN_VCHANNEL1); } /* @@ -667,7 +644,8 @@ static void mxs_lradc_prepare_y_pos(struct mxs_lradc *lradc) mxs_lradc_reg_set(lradc, mxs_lradc_drive_y_plate(lradc), LRADC_CTRL0); lradc->cur_plate = LRADC_SAMPLE_Y; - mxs_lradc_setup_ts_channel(lradc, TS_CH_XM); + mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL1, TS_CH_XM); + mxs_lradc_setup_ts_channel(lradc, TOUCHSCREEN_VCHANNEL1); } /* @@ -688,7 +666,10 @@ static void mxs_lradc_prepare_pressure(struct mxs_lradc *lradc) mxs_lradc_reg_set(lradc, mxs_lradc_drive_pressure(lradc), LRADC_CTRL0); lradc->cur_plate = LRADC_SAMPLE_PRESSURE; - mxs_lradc_setup_ts_pressure(lradc, TS_CH_XP, TS_CH_YM); + mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL1, TS_CH_YM); + mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL2, TS_CH_XP); + mxs_lradc_setup_ts_pressure(lradc, TOUCHSCREEN_VCHANNEL2, + TOUCHSCREEN_VCHANNEL1); } static void mxs_lradc_enable_touch_detection(struct mxs_lradc *lradc) @@ -701,6 +682,19 @@ static void mxs_lradc_enable_touch_detection(struct mxs_lradc *lradc) mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1); } +static void mxs_lradc_start_touch_event(struct mxs_lradc *lradc) +{ + mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, + LRADC_CTRL1); + mxs_lradc_reg_set(lradc, + LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1), LRADC_CTRL1); + /* + * start with the Y-pos, because it uses nearly the same plate + * settings like the touch detection + */ + mxs_lradc_prepare_y_pos(lradc); +} + static void mxs_lradc_report_ts_event(struct mxs_lradc *lradc) { input_report_abs(lradc->ts_input, ABS_X, lradc->ts_x_pos); @@ -718,10 +712,12 @@ static void mxs_lradc_complete_touch_event(struct mxs_lradc *lradc) * start a dummy conversion to burn time to settle the signals * note: we are not interested in the conversion's value */ - mxs_lradc_reg_wrt(lradc, 0, LRADC_CH(5)); - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1); - mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(5), LRADC_CTRL1); - mxs_lradc_reg_wrt(lradc, LRADC_DELAY_TRIGGER(1 << 5) | + mxs_lradc_reg_wrt(lradc, 0, LRADC_CH(TOUCHSCREEN_VCHANNEL1)); + mxs_lradc_reg_clear(lradc, + LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) | + LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2), LRADC_CTRL1); + mxs_lradc_reg_wrt(lradc, + LRADC_DELAY_TRIGGER(1 << TOUCHSCREEN_VCHANNEL1) | LRADC_DELAY_KICK | LRADC_DELAY_DELAY(10), /* waste 5 ms */ LRADC_DELAY(2)); } @@ -753,59 +749,45 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid) /* if it is released, wait for the next touch via IRQ */ lradc->cur_plate = LRADC_TOUCH; - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1); + mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2)); + mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3)); + mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ | + LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) | + LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1), LRADC_CTRL1); mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1); } /* touchscreen's state machine */ static void mxs_lradc_handle_touch(struct mxs_lradc *lradc) { - int val; - switch (lradc->cur_plate) { case LRADC_TOUCH: - /* - * start with the Y-pos, because it uses nearly the same plate - * settings like the touch detection - */ - if (mxs_lradc_check_touch_event(lradc)) { - mxs_lradc_reg_clear(lradc, - LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, - LRADC_CTRL1); - mxs_lradc_prepare_y_pos(lradc); - } + if (mxs_lradc_check_touch_event(lradc)) + mxs_lradc_start_touch_event(lradc); mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1); return; case LRADC_SAMPLE_Y: - val = mxs_lradc_read_ts_channel(lradc); - if (val < 0) { - mxs_lradc_enable_touch_detection(lradc); /* re-start */ - return; - } - lradc->ts_y_pos = val; + lradc->ts_y_pos = mxs_lradc_read_raw_channel(lradc, + TOUCHSCREEN_VCHANNEL1); mxs_lradc_prepare_x_pos(lradc); return; case LRADC_SAMPLE_X: - val = mxs_lradc_read_ts_channel(lradc); - if (val < 0) { - mxs_lradc_enable_touch_detection(lradc); /* re-start */ - return; - } - lradc->ts_x_pos = val; + lradc->ts_x_pos = mxs_lradc_read_raw_channel(lradc, + TOUCHSCREEN_VCHANNEL1); mxs_lradc_prepare_pressure(lradc); return; case LRADC_SAMPLE_PRESSURE: - lradc->ts_pressure = - mxs_lradc_read_ts_pressure(lradc, TS_CH_XP, TS_CH_YM); + lradc->ts_pressure = mxs_lradc_read_ts_pressure(lradc, + TOUCHSCREEN_VCHANNEL2, + TOUCHSCREEN_VCHANNEL1); mxs_lradc_complete_touch_event(lradc); return; case LRADC_SAMPLE_VALID: - val = mxs_lradc_read_ts_channel(lradc); /* ignore the value */ mxs_lradc_finish_touch_event(lradc, 1); break; } @@ -1083,9 +1065,8 @@ static void mxs_lradc_disable_ts(struct mxs_lradc *lradc) { /* stop all interrupts from firing */ mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN | - LRADC_CTRL1_LRADC_IRQ_EN(2) | LRADC_CTRL1_LRADC_IRQ_EN(3) | - LRADC_CTRL1_LRADC_IRQ_EN(4) | LRADC_CTRL1_LRADC_IRQ_EN(5), - LRADC_CTRL1); + LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) | + LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL2), LRADC_CTRL1); /* Power-down touchscreen touch-detect circuitry. */ mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0); @@ -1151,26 +1132,29 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data) struct iio_dev *iio = data; struct mxs_lradc *lradc = iio_priv(iio); unsigned long reg = readl(lradc->base + LRADC_CTRL1); + uint32_t clr_irq = mxs_lradc_irq_mask(lradc); const uint32_t ts_irq_mask = LRADC_CTRL1_TOUCH_DETECT_IRQ | - LRADC_CTRL1_LRADC_IRQ(2) | - LRADC_CTRL1_LRADC_IRQ(3) | - LRADC_CTRL1_LRADC_IRQ(4) | - LRADC_CTRL1_LRADC_IRQ(5); + LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) | + LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2); if (!(reg & mxs_lradc_irq_mask(lradc))) return IRQ_NONE; - if (lradc->use_touchscreen && (reg & ts_irq_mask)) + if (lradc->use_touchscreen && (reg & ts_irq_mask)) { mxs_lradc_handle_touch(lradc); + /* Make sure we don't clear the next conversion's interrupt. */ + clr_irq &= ~(LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) | + LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2)); + } + if (iio_buffer_enabled(iio)) iio_trigger_poll(iio->trig); else if (reg & LRADC_CTRL1_LRADC_IRQ(0)) complete(&lradc->completion); - mxs_lradc_reg_clear(lradc, reg & mxs_lradc_irq_mask(lradc), - LRADC_CTRL1); + mxs_lradc_reg_clear(lradc, reg & clr_irq, LRADC_CTRL1); return IRQ_HANDLED; } @@ -1346,7 +1330,7 @@ static bool mxs_lradc_validate_scan_mask(struct iio_dev *iio, if (lradc->use_touchbutton) rsvd_chans++; if (lradc->use_touchscreen) - rsvd_chans++; + rsvd_chans += 2; /* Test for attempts to map channels with special mode of operation. */ if (bitmap_intersects(mask, &rsvd_mask, LRADC_MAX_TOTAL_CHANS)) -- cgit v1.2.3-59-g8ed1b From 86bf7f3ef7e961e91e16dceb31ae0f583483b204 Mon Sep 17 00:00:00 2001 From: Kristina Martšenko Date: Sun, 25 Jan 2015 18:28:20 +0200 Subject: iio: mxs-lradc: make ADC reads not disable touchscreen interrupts MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Reading a channel through sysfs, or starting a buffered capture, will currently turn off the touchscreen. This is because the read_raw() and buffer preenable()/postdisable() callbacks disable interrupts for all LRADC channels, including those the touchscreen uses. So make the callbacks only disable interrupts for the channels they use. This means channel 0 for read_raw() and channels 0-5 for the buffer (if the touchscreen is enabled). Since the touchscreen uses different channels (6 and 7), it no longer gets turned off. Note that only i.MX28 is affected by this issue, i.MX23 should be fine. Signed-off-by: Kristina Martšenko Reviewed-by: Marek Vasut Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/staging/iio/adc/mxs-lradc.c | 20 +++++++++++++++----- 1 file changed, 15 insertions(+), 5 deletions(-) diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c index 4e574b76ead0..653af03bc69d 100644 --- a/drivers/staging/iio/adc/mxs-lradc.c +++ b/drivers/staging/iio/adc/mxs-lradc.c @@ -220,6 +220,9 @@ struct mxs_lradc { */ #define TOUCHSCREEN_VCHANNEL1 7 #define TOUCHSCREEN_VCHANNEL2 6 +#define BUFFER_VCHANS_LIMITED 0x3f +#define BUFFER_VCHANS_ALL 0xff + u8 buffer_vchans; /* * Furthermore, certain LRADC channels are shared between touchscreen @@ -819,7 +822,7 @@ static int mxs_lradc_read_single(struct iio_dev *iio_dev, int chan, int *val) * used if doing raw sampling. */ if (lradc->soc == IMX28_LRADC) - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK, + mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1); mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0); @@ -1266,8 +1269,9 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio) } if (lradc->soc == IMX28_LRADC) - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK, - LRADC_CTRL1); + mxs_lradc_reg_clear(lradc, + lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET, + LRADC_CTRL1); mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0); for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) { @@ -1303,8 +1307,9 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio) mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0); if (lradc->soc == IMX28_LRADC) - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK, - LRADC_CTRL1); + mxs_lradc_reg_clear(lradc, + lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET, + LRADC_CTRL1); kfree(lradc->buffer); mutex_unlock(&lradc->lock); @@ -1542,6 +1547,11 @@ static int mxs_lradc_probe(struct platform_device *pdev) touch_ret = mxs_lradc_probe_touchscreen(lradc, node); + if (touch_ret == 0) + lradc->buffer_vchans = BUFFER_VCHANS_LIMITED; + else + lradc->buffer_vchans = BUFFER_VCHANS_ALL; + /* Grab all IRQ sources */ for (i = 0; i < of_cfg->irq_count; i++) { lradc->irq[i] = platform_get_irq(pdev, i); -- cgit v1.2.3-59-g8ed1b From 6abe0300a1d5242f4ff89257197f284679af1a06 Mon Sep 17 00:00:00 2001 From: Kristina Martšenko Date: Sun, 25 Jan 2015 18:28:21 +0200 Subject: iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Reading a channel through sysfs, or starting a buffered capture, can occasionally turn off the touchscreen. This is because the read_raw() and buffer preenable()/postdisable() callbacks unschedule current conversions on all channels. If a delay channel happens to schedule a touchscreen conversion at the same time, the conversion gets cancelled and the touchscreen sequence stops. This is probably related to this note from the reference manual: "If a delay group schedules channels to be sampled and a manual write to the schedule field in CTRL0 occurs while the block is discarding samples, the LRADC will switch to the new schedule and will not sample the channels that were previously scheduled. The time window for this to happen is very small and lasts only while the LRADC is discarding samples." So make the callbacks only unschedule conversions for the channels they use. This means channel 0 for read_raw() and channels 0-5 for the buffer (if the touchscreen is enabled). Since the touchscreen uses different channels (6 and 7), it no longer gets turned off. This is tested and fixes the issue on i.MX28, but hasn't been tested on i.MX23. Signed-off-by: Kristina Martšenko Reviewed-by: Marek Vasut Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/staging/iio/adc/mxs-lradc.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c index 653af03bc69d..d2e0c275bf4d 100644 --- a/drivers/staging/iio/adc/mxs-lradc.c +++ b/drivers/staging/iio/adc/mxs-lradc.c @@ -824,7 +824,7 @@ static int mxs_lradc_read_single(struct iio_dev *iio_dev, int chan, int *val) if (lradc->soc == IMX28_LRADC) mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1); - mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0); + mxs_lradc_reg_clear(lradc, 0x1, LRADC_CTRL0); /* Enable / disable the divider per requirement */ if (test_bit(chan, &lradc->is_divided)) @@ -1272,7 +1272,7 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio) mxs_lradc_reg_clear(lradc, lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET, LRADC_CTRL1); - mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0); + mxs_lradc_reg_clear(lradc, lradc->buffer_vchans, LRADC_CTRL0); for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) { ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs); @@ -1305,7 +1305,7 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio) mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK, LRADC_DELAY(0)); - mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0); + mxs_lradc_reg_clear(lradc, lradc->buffer_vchans, LRADC_CTRL0); if (lradc->soc == IMX28_LRADC) mxs_lradc_reg_clear(lradc, lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET, -- cgit v1.2.3-59-g8ed1b From 89bb35e200bee745c539a96666e0792301ca40f1 Mon Sep 17 00:00:00 2001 From: Kristina Martšenko Date: Sun, 25 Jan 2015 18:28:22 +0200 Subject: iio: mxs-lradc: only update the buffer when its conversions have finished MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Using the touchscreen while running buffered capture results in the buffer reporting lots of wrong values, often just zeros. This is because we push readings to the buffer every time a touchscreen interrupt arrives, including when the buffer's own conversions have not yet finished. So let's only push to the buffer when its conversions are ready. Signed-off-by: Kristina Martšenko Reviewed-by: Marek Vasut Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/staging/iio/adc/mxs-lradc.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c index d2e0c275bf4d..ebcbd12d48b9 100644 --- a/drivers/staging/iio/adc/mxs-lradc.c +++ b/drivers/staging/iio/adc/mxs-lradc.c @@ -1152,10 +1152,12 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data) LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2)); } - if (iio_buffer_enabled(iio)) - iio_trigger_poll(iio->trig); - else if (reg & LRADC_CTRL1_LRADC_IRQ(0)) + if (iio_buffer_enabled(iio)) { + if (reg & lradc->buffer_vchans) + iio_trigger_poll(iio->trig); + } else if (reg & LRADC_CTRL1_LRADC_IRQ(0)) { complete(&lradc->completion); + } mxs_lradc_reg_clear(lradc, reg & clr_irq, LRADC_CTRL1); -- cgit v1.2.3-59-g8ed1b From f7067a5ad717d4dbb4faa3ec56744152f6ba97ad Mon Sep 17 00:00:00 2001 From: Rasmus Villemoes Date: Fri, 23 Jan 2015 00:09:56 +0100 Subject: staging: iio: ad2s1200: Fix sign extension The line above makes vel a 12-bit quantity (st->rx[] is u8). The intention is to sign-extend vel using bit 11 as the sign bit. But because of C's promotion rules "vel = (vel << 4) >> 4;" is actually a no-op, since vel is promoted to int before the inner shift. sign_extend32 works equally well for 8 and 16 bits types, so use that. Signed-off-by: Rasmus Villemoes Acked-by: Lars-Peter Clausen Signed-off-by: Jonathan Cameron --- drivers/staging/iio/resolver/ad2s1200.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/staging/iio/resolver/ad2s1200.c b/drivers/staging/iio/resolver/ad2s1200.c index 017d2f8379b7..c17893b4918c 100644 --- a/drivers/staging/iio/resolver/ad2s1200.c +++ b/drivers/staging/iio/resolver/ad2s1200.c @@ -18,6 +18,7 @@ #include #include #include +#include #include #include @@ -68,7 +69,7 @@ static int ad2s1200_read_raw(struct iio_dev *indio_dev, break; case IIO_ANGL_VEL: vel = (((s16)(st->rx[0])) << 4) | ((st->rx[1] & 0xF0) >> 4); - vel = (vel << 4) >> 4; + vel = sign_extend32(vel, 11); *val = vel; break; default: -- cgit v1.2.3-59-g8ed1b From 19e353f2b344ad86cea6ebbc0002e5f903480a90 Mon Sep 17 00:00:00 2001 From: Rasmus Villemoes Date: Fri, 23 Jan 2015 00:34:02 +0100 Subject: iio: imu: adis16400: Fix sign extension The intention is obviously to sign-extend a 12 bit quantity. But because of C's promotion rules, the assignment is equivalent to "val16 &= 0xfff;". Use the proper API for this. Signed-off-by: Rasmus Villemoes Acked-by: Lars-Peter Clausen Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/iio/imu/adis16400_core.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/iio/imu/adis16400_core.c b/drivers/iio/imu/adis16400_core.c index b70873de04ea..fa795dcd5f75 100644 --- a/drivers/iio/imu/adis16400_core.c +++ b/drivers/iio/imu/adis16400_core.c @@ -26,6 +26,7 @@ #include #include #include +#include #include #include @@ -414,7 +415,7 @@ static int adis16400_read_raw(struct iio_dev *indio_dev, mutex_unlock(&indio_dev->mlock); if (ret) return ret; - val16 = ((val16 & 0xFFF) << 4) >> 4; + val16 = sign_extend32(val16, 11); *val = val16; return IIO_VAL_INT; case IIO_CHAN_INFO_OFFSET: -- cgit v1.2.3-59-g8ed1b From 03305e535cd5cdc1079b32909bf4b2dd67d46f7f Mon Sep 17 00:00:00 2001 From: Stefan Wahren Date: Sat, 3 Jan 2015 20:34:12 +0000 Subject: iio: mxs-lradc: fix iio channel map regression Since commit c8231a9af8147f8a ("iio: mxs-lradc: compute temperature from channel 8 and 9") with the removal of adc channel 9 there is no 1-1 mapping in the channel spec. All hwmon channel values above 9 are accessible via there index minus one. So add a hidden iio channel 9 to fix this issue. Signed-off-by: Stefan Wahren Acked-by: Alexandre Belloni Reviewed-by: Marek Vasut Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/staging/iio/adc/mxs-lradc.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c index ebcbd12d48b9..351339ccaad6 100644 --- a/drivers/staging/iio/adc/mxs-lradc.c +++ b/drivers/staging/iio/adc/mxs-lradc.c @@ -1397,6 +1397,13 @@ static const struct iio_chan_spec mxs_lradc_chan_spec[] = { .channel = 8, .scan_type = {.sign = 'u', .realbits = 18, .storagebits = 32,}, }, + /* Hidden channel to keep indexes */ + { + .type = IIO_TEMP, + .indexed = 1, + .scan_index = -1, + .channel = 9, + }, MXS_ADC_CHAN(10, IIO_VOLTAGE), /* VDDIO */ MXS_ADC_CHAN(11, IIO_VOLTAGE), /* VTH */ MXS_ADC_CHAN(12, IIO_VOLTAGE), /* VDDA */ -- cgit v1.2.3-59-g8ed1b From 9e128ced3851d2802b6db870f6b2e93f449ce013 Mon Sep 17 00:00:00 2001 From: Angelo Compagnucci Date: Wed, 4 Feb 2015 15:14:26 +0100 Subject: iio:adc:mcp3422 Fix incorrect scales table This patch fixes uncorrect order of mcp3422_scales table, the values was erroneously transposed. It removes also an unused array and a wrong comment. Signed-off-by: Angelo Compagnucci Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/iio/adc/mcp3422.c | 17 ++++------------- 1 file changed, 4 insertions(+), 13 deletions(-) diff --git a/drivers/iio/adc/mcp3422.c b/drivers/iio/adc/mcp3422.c index 51672256072b..b96c636470ef 100644 --- a/drivers/iio/adc/mcp3422.c +++ b/drivers/iio/adc/mcp3422.c @@ -58,20 +58,11 @@ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ), \ } -/* LSB is in nV to eliminate floating point */ -static const u32 rates_to_lsb[] = {1000000, 250000, 62500, 15625}; - -/* - * scales calculated as: - * rates_to_lsb[sample_rate] / (1 << pga); - * pga is 1 for 0, 2 - */ - static const int mcp3422_scales[4][4] = { - { 1000000, 250000, 62500, 15625 }, - { 500000 , 125000, 31250, 7812 }, - { 250000 , 62500 , 15625, 3906 }, - { 125000 , 31250 , 7812 , 1953 } }; + { 1000000, 500000, 250000, 125000 }, + { 250000 , 125000, 62500 , 31250 }, + { 62500 , 31250 , 15625 , 7812 }, + { 15625 , 7812 , 3906 , 1953 } }; /* Constant msleep times for data acquisitions */ static const int mcp3422_read_times[4] = { -- cgit v1.2.3-59-g8ed1b From da019f59cb16570e78feaf10380ac65a3a06861e Mon Sep 17 00:00:00 2001 From: Urs Fässler Date: Mon, 2 Feb 2015 17:12:23 +0100 Subject: iio: ad5686: fix optional reference voltage declaration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When not using the "_optional" function, a dummy regulator is returned and the driver fails to initialize. Signed-off-by: Urs Fässler Acked-by: Lars-Peter Clausen Cc: stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/iio/dac/ad5686.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/iio/dac/ad5686.c b/drivers/iio/dac/ad5686.c index f57562aa396f..15c73e20272d 100644 --- a/drivers/iio/dac/ad5686.c +++ b/drivers/iio/dac/ad5686.c @@ -322,7 +322,7 @@ static int ad5686_probe(struct spi_device *spi) st = iio_priv(indio_dev); spi_set_drvdata(spi, indio_dev); - st->reg = devm_regulator_get(&spi->dev, "vcc"); + st->reg = devm_regulator_get_optional(&spi->dev, "vcc"); if (!IS_ERR(st->reg)) { ret = regulator_enable(st->reg); if (ret) -- cgit v1.2.3-59-g8ed1b From dd3733b3e798daf778a1ec08557f388f00fdc2f6 Mon Sep 17 00:00:00 2001 From: Alexey Andriyanov Date: Fri, 6 Feb 2015 22:32:20 +0300 Subject: ipvs: fix inability to remove a mixed-family RS The current code prevents any operation with a mixed-family dest unless IP_VS_CONN_F_TUNNEL flag is set. The problem is that it's impossible for the client to follow this rule, because ip_vs_genl_parse_dest does not even read the destination conn_flags when cmd = IPVS_CMD_DEL_DEST (need_full_dest = 0). Also, not every client can pass this flag when removing a dest. ipvsadm, for example, does not support the "-i" command line option together with the "-d" option. This change disables any checks for mixed-family on IPVS_CMD_DEL_DEST command. Signed-off-by: Alexey Andriyanov Fixes: bc18d37f676f ("ipvs: Allow heterogeneous pools now that we support them") Acked-by: Julian Anastasov Signed-off-by: Simon Horman --- net/netfilter/ipvs/ip_vs_ctl.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/netfilter/ipvs/ip_vs_ctl.c b/net/netfilter/ipvs/ip_vs_ctl.c index b8295a430a56..fdcda8be1f0f 100644 --- a/net/netfilter/ipvs/ip_vs_ctl.c +++ b/net/netfilter/ipvs/ip_vs_ctl.c @@ -3399,7 +3399,7 @@ static int ip_vs_genl_set_cmd(struct sk_buff *skb, struct genl_info *info) if (udest.af == 0) udest.af = svc->af; - if (udest.af != svc->af) { + if (udest.af != svc->af && cmd != IPVS_CMD_DEL_DEST) { /* The synchronization protocol is incompatible * with mixed family services */ -- cgit v1.2.3-59-g8ed1b From 0b1f6ec7a5fb3faff1a62afee132dac316eec63d Mon Sep 17 00:00:00 2001 From: Kuninori Morimoto Date: Mon, 9 Feb 2015 08:05:22 +0000 Subject: ASoC: rsnd: set device data before snd_soc_register_platform/component Set device data before snd_soc_register_platform/component. Otherwise, it will use NULL pointer if user calls unbind -> bind or rmmod -> insmod Signed-off-by: Kuninori Morimoto Signed-off-by: Mark Brown --- sound/soc/sh/rcar/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/soc/sh/rcar/core.c b/sound/soc/sh/rcar/core.c index 75308bbc2ce8..fc227d3bc021 100644 --- a/sound/soc/sh/rcar/core.c +++ b/sound/soc/sh/rcar/core.c @@ -1268,6 +1268,8 @@ static int rsnd_probe(struct platform_device *pdev) goto exit_snd_probe; } + dev_set_drvdata(dev, priv); + /* * asoc register */ @@ -1284,8 +1286,6 @@ static int rsnd_probe(struct platform_device *pdev) goto exit_snd_soc; } - dev_set_drvdata(dev, priv); - pm_runtime_enable(dev); dev_info(dev, "probed\n"); -- cgit v1.2.3-59-g8ed1b From 541b03ad6cfe0e415273f096fd8c47d2879c6c15 Mon Sep 17 00:00:00 2001 From: Nicolin Chen Date: Tue, 10 Feb 2015 21:31:43 -0800 Subject: ASoC: fsl_ssi: Fix the incorrect limitation of the bit clock rate According to i.MX Reference Manual, the bit-clock frequency generated by SSI must be never greater than 1/5 of the peripheral clock frequency. This peripheral clock, however, is not baudclk but the IPG clock (i.e. ssi_private->clk in the fsl_ssi driver). So this patch just simply fixes the incorrect limitation applied to the bit clock (baudclk) rate. Signed-off-by: Nicolin Chen Signed-off-by: Mark Brown --- sound/soc/fsl/fsl_ssi.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c index 059496ed9ad7..d7365c5d7ec0 100644 --- a/sound/soc/fsl/fsl_ssi.c +++ b/sound/soc/fsl/fsl_ssi.c @@ -603,10 +603,6 @@ static int fsl_ssi_set_bclk(struct snd_pcm_substream *substream, factor = (div2 + 1) * (7 * psr + 1) * 2; for (i = 0; i < 255; i++) { - /* The bclk rate must be smaller than 1/5 sysclk rate */ - if (factor * (i + 1) < 5) - continue; - tmprate = freq * factor * (i + 2); if (baudclk_is_used) @@ -614,6 +610,13 @@ static int fsl_ssi_set_bclk(struct snd_pcm_substream *substream, else clkrate = clk_round_rate(ssi_private->baudclk, tmprate); + /* + * Hardware limitation: The bclk rate must be + * never greater than 1/5 IPG clock rate + */ + if (clkrate * 5 > clk_get_rate(ssi_private->clk)) + continue; + clkrate /= factor; afreq = clkrate / (i + 1); -- cgit v1.2.3-59-g8ed1b From ffa047577127336861d91f3934133f8e8906d1b4 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Wed, 11 Feb 2015 13:13:18 -0800 Subject: ASoC: Fix MAX98357A codec driver dependencies The max98357a driver depends on GPIOLIB. This may cause the following build failure. sound/soc/codecs/max98357a.c: In function 'max98357a_daiops_trigger': sound/soc/codecs/max98357a.c:30:3: error: implicit declaration of function 'gpiod_set_value' sound/soc/codecs/max98357a.c: In function 'max98357a_codec_probe': sound/soc/codecs/max98357a.c:55:2: error: implicit declaration of function 'devm_gpiod_get' sound/soc/codecs/max98357a.c:61:2: error: implicit declaration of function 'gpiod_direction_output' Seen with mips:allmodconfig as well as various randconfig builds. Fixes: af5adf129369 ("ASoC: max98357a: Add MAX98357A codec driver") Cc: Kenneth Westfield Signed-off-by: Guenter Roeck Signed-off-by: Mark Brown --- sound/soc/codecs/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 064e6c18e109..ea9f0e31f9d4 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -69,7 +69,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_MAX98088 if I2C select SND_SOC_MAX98090 if I2C select SND_SOC_MAX98095 if I2C - select SND_SOC_MAX98357A + select SND_SOC_MAX98357A if GPIOLIB select SND_SOC_MAX9850 if I2C select SND_SOC_MAX9768 if I2C select SND_SOC_MAX9877 if I2C -- cgit v1.2.3-59-g8ed1b From 5c8be987d4d9c0262e6229e342fa0da8a5aeee47 Mon Sep 17 00:00:00 2001 From: Vincent Stehlé Date: Wed, 11 Feb 2015 23:08:59 +0100 Subject: ASoC: max98357a: Fix missing include MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This fixes the following compilation errors: sound/soc/codecs/max98357a.c: In function ‘max98357a_daiops_trigger’: sound/soc/codecs/max98357a.c:30:3: error: implicit declaration of function ‘gpiod_set_value’ [-Werror=implicit-function-declaration] sound/soc/codecs/max98357a.c: In function ‘max98357a_codec_probe’: sound/soc/codecs/max98357a.c:55:2: error: implicit declaration of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration] sound/soc/codecs/max98357a.c:61:2: error: implicit declaration of function ‘gpiod_direction_output’ [-Werror=implicit-function-declaration] cc1: some warnings being treated as errors Signed-off-by: Vincent Stehlé Cc: Kenneth Westfield Cc: Mark Brown Signed-off-by: Mark Brown --- sound/soc/codecs/max98357a.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/codecs/max98357a.c b/sound/soc/codecs/max98357a.c index 1806333ea29e..f493fb6fd4ea 100644 --- a/sound/soc/codecs/max98357a.c +++ b/sound/soc/codecs/max98357a.c @@ -14,6 +14,7 @@ #include #include +#include #include #define DRV_NAME "max98357a" -- cgit v1.2.3-59-g8ed1b From a7e6645ee3fef358fb1d88b4a2729d29a467c61a Mon Sep 17 00:00:00 2001 From: Ping Cheng Date: Wed, 4 Feb 2015 16:01:54 -0800 Subject: HID: wacom: Add missing ABS_MISC event and feature declaration for 27QHD 27QHD has the same x_min/y_min (WACOM_CINTIQ_OFFSET) as other Cintiqs. ABS_MISC event is required for PAD packet to work properly with xf86-input-wacom. Signed-off-by: Ping Cheng Signed-off-by: Jiri Kosina --- drivers/hid/wacom_wac.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/drivers/hid/wacom_wac.c b/drivers/hid/wacom_wac.c index 1a6507999a65..046351cf17f3 100644 --- a/drivers/hid/wacom_wac.c +++ b/drivers/hid/wacom_wac.c @@ -778,6 +778,11 @@ static int wacom_intuos_irq(struct wacom_wac *wacom) input_report_abs(input, ABS_X, be16_to_cpup((__be16 *)&data[4])); input_report_abs(input, ABS_Y, be16_to_cpup((__be16 *)&data[6])); input_report_abs(input, ABS_Z, be16_to_cpup((__be16 *)&data[8])); + if ((data[2] & 0x07) | data[4] | data[5] | data[6] | data[7] | data[8] | data[9]) { + input_report_abs(input, ABS_MISC, PAD_DEVICE_ID); + } else { + input_report_abs(input, ABS_MISC, 0); + } } else if (features->type == CINTIQ_HYBRID) { /* * Do not send hardware buttons under Android. They @@ -2725,9 +2730,9 @@ static const struct wacom_features wacom_features_0xF6 = .oVid = USB_VENDOR_ID_WACOM, .oPid = 0xf8, .touch_max = 10, .check_for_hid_type = true, .hid_type = HID_TYPE_USBNONE }; static const struct wacom_features wacom_features_0x32A = - { "Wacom Cintiq 27QHD", 119740, 67520, 2047, - 63, WACOM_27QHD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES, - WACOM_27QHD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES }; + { "Wacom Cintiq 27QHD", 119740, 67520, 2047, 63, + WACOM_27QHD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES, + WACOM_CINTIQ_OFFSET, WACOM_CINTIQ_OFFSET }; static const struct wacom_features wacom_features_0x32B = { "Wacom Cintiq 27QHD touch", 119740, 67520, 2047, 63, WACOM_27QHD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES, -- cgit v1.2.3-59-g8ed1b From fb5ab7296a2bea17c38fae48af2808a07049ac90 Mon Sep 17 00:00:00 2001 From: Kiran Padwal Date: Thu, 12 Feb 2015 14:38:02 +0530 Subject: ASoC: omap-hdmi-audio: Add missing error check for devm_kzalloc This patch add a missing check on the return value of devm_kzalloc, which would cause a NULL pointer dereference in a OOM situation. Signed-off-by: Kiran Padwal Acked-by: Peter Ujfalusi Signed-off-by: Mark Brown --- sound/soc/omap/omap-hdmi-audio.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/sound/soc/omap/omap-hdmi-audio.c b/sound/soc/omap/omap-hdmi-audio.c index 3f9ac7dbdc80..069ad451d05d 100644 --- a/sound/soc/omap/omap-hdmi-audio.c +++ b/sound/soc/omap/omap-hdmi-audio.c @@ -352,6 +352,9 @@ static int omap_hdmi_audio_probe(struct platform_device *pdev) return ret; card = devm_kzalloc(dev, sizeof(*card), GFP_KERNEL); + if (!card) + return -ENOMEM; + card->name = devm_kasprintf(dev, GFP_KERNEL, "HDMI %s", dev_name(ad->dssdev)); card->owner = THIS_MODULE; -- cgit v1.2.3-59-g8ed1b From 7bd345c9e87d879d696c6843fe200b60c2051c84 Mon Sep 17 00:00:00 2001 From: Mengdong Lin Date: Fri, 13 Feb 2015 19:21:25 +0800 Subject: ASoC: Intel: set initial runtime PM status to active for ACPI-enumerated ADSP The ADSP on Braswell/Baytrail is an ACPI device. This patch sets its initial runtime PM status to active. Otherwise, its initial status is suspended and runtime_suspend ops will not be called after probe and thus cannot further trigger ACPI _PS3 (D3) method to put the device into low power D3cold state. Signed-off-by: Mengdong Lin Signed-off-by: Mark Brown --- sound/soc/intel/sst/sst.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/sound/soc/intel/sst/sst.c b/sound/soc/intel/sst/sst.c index 8a8d56a146e7..d6ea80076ea2 100644 --- a/sound/soc/intel/sst/sst.c +++ b/sound/soc/intel/sst/sst.c @@ -379,6 +379,10 @@ void sst_configure_runtime_pm(struct intel_sst_drv *ctx) * initially active. So change the state to active before * enabling the pm */ + + if (!acpi_disabled) + pm_runtime_set_active(ctx->dev); + pm_runtime_enable(ctx->dev); if (acpi_disabled) -- cgit v1.2.3-59-g8ed1b From 49e19d5f27aaa004692a2080453b9cc4d4fb6ec4 Mon Sep 17 00:00:00 2001 From: Roberta Dobrescu Date: Thu, 12 Feb 2015 23:00:14 +0200 Subject: iio: light: jsa1212: Select REGMAP_I2C This patch adds missing 'select' statement for jsa1212 driver. Without regmap_i2c, we get the following error when loading the module: Unknown symbol devm_regmap_init_i2c. Signed-off-by: Roberta Dobrescu Reviewed-by: Daniel Baluta Signed-off-by: Jonathan Cameron --- drivers/iio/light/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig index ae68c64bdad3..e0ed374b33fd 100644 --- a/drivers/iio/light/Kconfig +++ b/drivers/iio/light/Kconfig @@ -126,6 +126,7 @@ config HID_SENSOR_PROX config JSA1212 tristate "JSA1212 ALS and proximity sensor driver" depends on I2C + select REGMAP_I2C help Say Y here if you want to build a IIO driver for JSA1212 proximity & ALS sensor device. -- cgit v1.2.3-59-g8ed1b From 8c3b3efb32e0fc5dc3c0a81c7f7639a14bebdb78 Mon Sep 17 00:00:00 2001 From: Roberta Dobrescu Date: Thu, 12 Feb 2015 23:00:15 +0200 Subject: iio: light: gp2ap020a00f: Select REGMAP_I2C This patch adds missing 'select' statement for gp2ap020a00f driver. Without regmap_i2c, we get the following error when loading the module: Unknown symbol devm_regmap_init_i2c. Signed-off-by: Roberta Dobrescu Reviewed-by: Daniel Baluta Signed-off-by: Jonathan Cameron --- drivers/iio/light/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig index 5bea821adcae..a338089f8077 100644 --- a/drivers/iio/light/Kconfig +++ b/drivers/iio/light/Kconfig @@ -62,6 +62,7 @@ config CM36651 config GP2AP020A00F tristate "Sharp GP2AP020A00F Proximity/ALS sensor" depends on I2C + select REGMAP_I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER select IRQ_WORK -- cgit v1.2.3-59-g8ed1b From e765537add38cf7967efa11999bb5daf84a6517d Mon Sep 17 00:00:00 2001 From: Jonathan Cameron Date: Sat, 14 Feb 2015 11:32:17 +0000 Subject: Revert "iio:humidity:si7020: fix pointer to i2c client" This reverts commit e0922e5e3ccb78aa0152e93dfbd1755ac39c8582. Requested by Andrey Smirnov. It incorrectly assumes that the level of indirection is not needed which is not true(probably because the driver incorrectly allocates sizeof(*client) instead of sizeof(*data) via devm_iio_device_alloc). If you look at the code of the probe function(see below) it is easy to see that what is being stored in the private memory of the IIO device instance is not a copy of a 'struct i2c_client' but a pointer to an instance passed as an argument to the probe function. struct i2c_client **data; int ret; < Some code skipped > indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*client)); if (!indio_dev) return -ENOMEM; data = iio_priv(indio_dev); *data = client; Without reverting this change any read of a raw value of this sensor leads to a kernel oops due to a NULL pointer de-reference on my hardware setup. Signed-off-by: Jonathan Cameron Cc: Stable@vger.kernel.org --- drivers/iio/humidity/si7020.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/iio/humidity/si7020.c b/drivers/iio/humidity/si7020.c index b54164677b89..69e49f58a455 100644 --- a/drivers/iio/humidity/si7020.c +++ b/drivers/iio/humidity/si7020.c @@ -45,12 +45,12 @@ static int si7020_read_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan, int *val, int *val2, long mask) { - struct i2c_client *client = iio_priv(indio_dev); + struct i2c_client **client = iio_priv(indio_dev); int ret; switch (mask) { case IIO_CHAN_INFO_RAW: - ret = i2c_smbus_read_word_data(client, + ret = i2c_smbus_read_word_data(*client, chan->type == IIO_TEMP ? SI7020CMD_TEMP_HOLD : SI7020CMD_RH_HOLD); -- cgit v1.2.3-59-g8ed1b From e01becbad300712a28f29b666e685536f45e83bc Mon Sep 17 00:00:00 2001 From: Andrey Smirnov Date: Thu, 12 Feb 2015 23:58:41 -0800 Subject: IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc Since only a pointer to struct i2c_client is stored in a private area of IIO device created by the driver there's no need to allocate sizeof(struct i2c_client) worth of storage. Pushed to stable as this is linked to the revert patch previously. Without this followup the original patch looks sensible. Signed-off-by: Andrey Smirnov Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/iio/humidity/si7020.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/iio/humidity/si7020.c b/drivers/iio/humidity/si7020.c index 69e49f58a455..fa3b809aff5e 100644 --- a/drivers/iio/humidity/si7020.c +++ b/drivers/iio/humidity/si7020.c @@ -126,7 +126,7 @@ static int si7020_probe(struct i2c_client *client, /* Wait the maximum power-up time after software reset. */ msleep(15); - indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*client)); + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); if (!indio_dev) return -ENOMEM; -- cgit v1.2.3-59-g8ed1b From e0b561ee78d82a4cc7792aa28fa4b1ea15325dcc Mon Sep 17 00:00:00 2001 From: Jiri Kosina Date: Sun, 15 Feb 2015 10:03:20 +0100 Subject: livepatch: fix format string in kobject_init_and_add() kobject_init_and_add() takes expects format string for a name, so we better provide it in order to avoid infoleaks if modules craft their mod->name in a special way. Reported-by: Fengguang Wu Reported-by: Kees Cook Acked-by: Seth Jennings Signed-off-by: Jiri Kosina --- kernel/livepatch/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/kernel/livepatch/core.c b/kernel/livepatch/core.c index ff7f47d026ac..69bf3aa3bde8 100644 --- a/kernel/livepatch/core.c +++ b/kernel/livepatch/core.c @@ -731,7 +731,7 @@ static int klp_init_func(struct klp_object *obj, struct klp_func *func) func->state = KLP_DISABLED; return kobject_init_and_add(&func->kobj, &klp_ktype_func, - obj->kobj, func->old_name); + obj->kobj, "%s", func->old_name); } /* parts of the initialization that is done only when the object is loaded */ @@ -807,7 +807,7 @@ static int klp_init_patch(struct klp_patch *patch) patch->state = KLP_DISABLED; ret = kobject_init_and_add(&patch->kobj, &klp_ktype_patch, - klp_root_kobj, patch->mod->name); + klp_root_kobj, "%s", patch->mod->name); if (ret) goto unlock; -- cgit v1.2.3-59-g8ed1b From 520aa7414bb590f39d0d1591b06018e60cbc7cf4 Mon Sep 17 00:00:00 2001 From: Pablo Neira Ayuso Date: Thu, 12 Feb 2015 22:15:31 +0100 Subject: netfilter: nft_compat: fix module refcount underflow Feb 12 18:20:42 nfdev kernel: ------------[ cut here ]------------ Feb 12 18:20:42 nfdev kernel: WARNING: CPU: 4 PID: 4359 at kernel/module.c:963 module_put+0x9b/0xba() Feb 12 18:20:42 nfdev kernel: CPU: 4 PID: 4359 Comm: ebtables-compat Tainted: G W 3.19.0-rc6+ #43 [...] Feb 12 18:20:42 nfdev kernel: Call Trace: Feb 12 18:20:42 nfdev kernel: [] dump_stack+0x4c/0x65 Feb 12 18:20:42 nfdev kernel: [] warn_slowpath_common+0x9c/0xb6 Feb 12 18:20:42 nfdev kernel: [] ? module_put+0x9b/0xba Feb 12 18:20:42 nfdev kernel: [] warn_slowpath_null+0x15/0x17 Feb 12 18:20:42 nfdev kernel: [] module_put+0x9b/0xba Feb 12 18:20:42 nfdev kernel: [] nft_match_destroy+0x45/0x4c Feb 12 18:20:42 nfdev kernel: [] nf_tables_rule_destroy+0x28/0x70 Reported-by: Arturo Borrero Gonzalez Signed-off-by: Pablo Neira Ayuso Tested-by: Arturo Borrero Gonzalez --- net/netfilter/nft_compat.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/net/netfilter/nft_compat.c b/net/netfilter/nft_compat.c index 265e190f2218..b6364869c2e0 100644 --- a/net/netfilter/nft_compat.c +++ b/net/netfilter/nft_compat.c @@ -578,8 +578,12 @@ nft_match_select_ops(const struct nft_ctx *ctx, struct xt_match *match = nft_match->ops.data; if (strcmp(match->name, mt_name) == 0 && - match->revision == rev && match->family == family) + match->revision == rev && match->family == family) { + if (!try_module_get(match->me)) + return ERR_PTR(-ENOENT); + return &nft_match->ops; + } } match = xt_request_find_match(family, mt_name, rev); @@ -648,8 +652,12 @@ nft_target_select_ops(const struct nft_ctx *ctx, struct xt_target *target = nft_target->ops.data; if (strcmp(target->name, tg_name) == 0 && - target->revision == rev && target->family == family) + target->revision == rev && target->family == family) { + if (!try_module_get(target->me)) + return ERR_PTR(-ENOENT); + return &nft_target->ops; + } } target = xt_request_find_target(family, tg_name, rev); -- cgit v1.2.3-59-g8ed1b From cef9ed86ed62eeffcd017882278bbece32001f86 Mon Sep 17 00:00:00 2001 From: Florian Westphal Date: Fri, 13 Feb 2015 12:47:50 +0100 Subject: netfilter: xt_recent: don't reject rule if new hitcount exceeds table max given: -A INPUT -m recent --update --seconds 30 --hitcount 4 and iptables-save > foo then iptables-restore < foo will fail with: kernel: xt_recent: hitcount (4) is larger than packets to be remembered (4) for table DEFAULT Even when the check is fixed, the restore won't work if the hitcount is increased to e.g. 6, since by the time checkentry runs it will find the 'old' incarnation of the table. We can avoid this by increasing the maximum threshold silently; we only have to rm all the current entries of the table (these entries would not have enough room to handle the increased hitcount). This even makes (not-very-useful) -A INPUT -m recent --update --seconds 30 --hitcount 4 -A INPUT -m recent --update --seconds 30 --hitcount 42 work. Fixes: abc86d0f99242b7f142b (netfilter: xt_recent: relax ip_pkt_list_tot restrictions) Tracked-down-by: Chris Vine Signed-off-by: Florian Westphal Signed-off-by: Pablo Neira Ayuso --- net/netfilter/xt_recent.c | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-) diff --git a/net/netfilter/xt_recent.c b/net/netfilter/xt_recent.c index 30dbe34915ae..45e1b30e4fb2 100644 --- a/net/netfilter/xt_recent.c +++ b/net/netfilter/xt_recent.c @@ -378,12 +378,11 @@ static int recent_mt_check(const struct xt_mtchk_param *par, mutex_lock(&recent_mutex); t = recent_table_lookup(recent_net, info->name); if (t != NULL) { - if (info->hit_count > t->nstamps_max_mask) { - pr_info("hitcount (%u) is larger than packets to be remembered (%u) for table %s\n", - info->hit_count, t->nstamps_max_mask + 1, - info->name); - ret = -EINVAL; - goto out; + if (nstamp_mask > t->nstamps_max_mask) { + spin_lock_bh(&recent_lock); + recent_table_flush(t); + t->nstamps_max_mask = nstamp_mask; + spin_unlock_bh(&recent_lock); } t->refcnt++; -- cgit v1.2.3-59-g8ed1b From 78296c97ca1fd3b104f12e1f1fbc06c46635990b Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Sun, 15 Feb 2015 19:03:45 -0800 Subject: netfilter: xt_socket: fix a stack corruption bug As soon as extract_icmp6_fields() returns, its local storage (automatic variables) is deallocated and can be overwritten. Lets add an additional parameter to make sure storage is valid long enough. While we are at it, adds some const qualifiers. Signed-off-by: Eric Dumazet Fixes: b64c9256a9b76 ("tproxy: added IPv6 support to the socket match") Signed-off-by: Pablo Neira Ayuso --- net/netfilter/xt_socket.c | 21 ++++++++++++--------- 1 file changed, 12 insertions(+), 9 deletions(-) diff --git a/net/netfilter/xt_socket.c b/net/netfilter/xt_socket.c index 1ba67931eb1b..13332dbf291d 100644 --- a/net/netfilter/xt_socket.c +++ b/net/netfilter/xt_socket.c @@ -243,12 +243,13 @@ static int extract_icmp6_fields(const struct sk_buff *skb, unsigned int outside_hdrlen, int *protocol, - struct in6_addr **raddr, - struct in6_addr **laddr, + const struct in6_addr **raddr, + const struct in6_addr **laddr, __be16 *rport, - __be16 *lport) + __be16 *lport, + struct ipv6hdr *ipv6_var) { - struct ipv6hdr *inside_iph, _inside_iph; + const struct ipv6hdr *inside_iph; struct icmp6hdr *icmph, _icmph; __be16 *ports, _ports[2]; u8 inside_nexthdr; @@ -263,12 +264,14 @@ extract_icmp6_fields(const struct sk_buff *skb, if (icmph->icmp6_type & ICMPV6_INFOMSG_MASK) return 1; - inside_iph = skb_header_pointer(skb, outside_hdrlen + sizeof(_icmph), sizeof(_inside_iph), &_inside_iph); + inside_iph = skb_header_pointer(skb, outside_hdrlen + sizeof(_icmph), + sizeof(*ipv6_var), ipv6_var); if (inside_iph == NULL) return 1; inside_nexthdr = inside_iph->nexthdr; - inside_hdrlen = ipv6_skip_exthdr(skb, outside_hdrlen + sizeof(_icmph) + sizeof(_inside_iph), + inside_hdrlen = ipv6_skip_exthdr(skb, outside_hdrlen + sizeof(_icmph) + + sizeof(*ipv6_var), &inside_nexthdr, &inside_fragoff); if (inside_hdrlen < 0) return 1; /* hjm: Packet has no/incomplete transport layer headers. */ @@ -315,10 +318,10 @@ xt_socket_get_sock_v6(struct net *net, const u8 protocol, static bool socket_mt6_v1_v2(const struct sk_buff *skb, struct xt_action_param *par) { - struct ipv6hdr *iph = ipv6_hdr(skb); + struct ipv6hdr ipv6_var, *iph = ipv6_hdr(skb); struct udphdr _hdr, *hp = NULL; struct sock *sk = skb->sk; - struct in6_addr *daddr = NULL, *saddr = NULL; + const struct in6_addr *daddr = NULL, *saddr = NULL; __be16 uninitialized_var(dport), uninitialized_var(sport); int thoff = 0, uninitialized_var(tproto); const struct xt_socket_mtinfo1 *info = (struct xt_socket_mtinfo1 *) par->matchinfo; @@ -342,7 +345,7 @@ socket_mt6_v1_v2(const struct sk_buff *skb, struct xt_action_param *par) } else if (tproto == IPPROTO_ICMPV6) { if (extract_icmp6_fields(skb, thoff, &tproto, &saddr, &daddr, - &sport, &dport)) + &sport, &dport, &ipv6_var)) return false; } else { return false; -- cgit v1.2.3-59-g8ed1b From f2de746c3f03de4d33a9e69a91e821bd4c2c1030 Mon Sep 17 00:00:00 2001 From: Mika Westerberg Date: Mon, 26 Jan 2015 16:29:32 +0200 Subject: HID: i2c-hid: The interrupt should be level sensitive The Microsoft HID over I2C specification says two things regarding the interrupt: 1) The interrupt should be level sensitive 2) The device keeps the interrupt asserted as long as it has more reports available. We've seen that at least some Atmel and N-Trig panels keep the line low as long as they have something to send. The current version of the driver only detects the first edge but then fails to read rest of the reports (as the line is still asserted). Make the driver follow the specification and configure the HID interrupt to be level sensitive. The Windows HID over I2C driver also seems to do the same. Signed-off-by: Mika Westerberg Acked-by: Benjamin Tissoires Signed-off-by: Jiri Kosina --- drivers/hid/i2c-hid/i2c-hid.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hid/i2c-hid/i2c-hid.c b/drivers/hid/i2c-hid/i2c-hid.c index d43e967e7533..8f1dfc5c5d9c 100644 --- a/drivers/hid/i2c-hid/i2c-hid.c +++ b/drivers/hid/i2c-hid/i2c-hid.c @@ -785,7 +785,7 @@ static int i2c_hid_init_irq(struct i2c_client *client) dev_dbg(&client->dev, "Requesting IRQ: %d\n", client->irq); ret = request_threaded_irq(client->irq, NULL, i2c_hid_irq, - IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + IRQF_TRIGGER_LOW | IRQF_ONESHOT, client->name, ihid); if (ret < 0) { dev_warn(&client->dev, -- cgit v1.2.3-59-g8ed1b From afe98939b37933ee8c3d0b5c42199d624d0408a6 Mon Sep 17 00:00:00 2001 From: Darren Salt Date: Thu, 29 Jan 2015 13:58:09 +0000 Subject: HID: saitek: add USB ID for older R.A.T. 7 Signed-off-by: Darren Salt Signed-off-by: Jiri Kosina --- drivers/hid/hid-core.c | 1 + drivers/hid/hid-ids.h | 1 + drivers/hid/hid-saitek.c | 2 ++ 3 files changed, 4 insertions(+) diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c index db4fb6e1cc5b..40b27ea28deb 100644 --- a/drivers/hid/hid-core.c +++ b/drivers/hid/hid-core.c @@ -1926,6 +1926,7 @@ static const struct hid_device_id hid_have_special_driver[] = { #endif #if IS_ENABLED(CONFIG_HID_SAITEK) { HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_PS1000) }, + { HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_RAT7_OLD) }, { HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_RAT7) }, { HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_MMO7) }, { HID_USB_DEVICE(USB_VENDOR_ID_MADCATZ, USB_DEVICE_ID_MADCATZ_RAT9) }, diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h index 46edb4d3ed28..b1ae48cdc0de 100644 --- a/drivers/hid/hid-ids.h +++ b/drivers/hid/hid-ids.h @@ -802,6 +802,7 @@ #define USB_VENDOR_ID_SAITEK 0x06a3 #define USB_DEVICE_ID_SAITEK_RUMBLEPAD 0xff17 #define USB_DEVICE_ID_SAITEK_PS1000 0x0621 +#define USB_DEVICE_ID_SAITEK_RAT7_OLD 0x0ccb #define USB_DEVICE_ID_SAITEK_RAT7 0x0cd7 #define USB_DEVICE_ID_SAITEK_MMO7 0x0cd0 diff --git a/drivers/hid/hid-saitek.c b/drivers/hid/hid-saitek.c index 5632c54eadf0..a014f21275d8 100644 --- a/drivers/hid/hid-saitek.c +++ b/drivers/hid/hid-saitek.c @@ -177,6 +177,8 @@ static int saitek_event(struct hid_device *hdev, struct hid_field *field, static const struct hid_device_id saitek_devices[] = { { HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_PS1000), .driver_data = SAITEK_FIX_PS1000 }, + { HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_RAT7_OLD), + .driver_data = SAITEK_RELEASE_MODE_RAT7 }, { HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_RAT7), .driver_data = SAITEK_RELEASE_MODE_RAT7 }, { HID_USB_DEVICE(USB_VENDOR_ID_MADCATZ, USB_DEVICE_ID_MADCATZ_RAT9), -- cgit v1.2.3-59-g8ed1b From f9d904acb3e7e9edb470cd824fe2a21bb0df86b8 Mon Sep 17 00:00:00 2001 From: Srinivas Pandruvada Date: Wed, 7 Jan 2015 10:14:43 -0800 Subject: HID: hid-sensor-hub: Correct documentation During changes to the interface, some documentation field comments were missed. Added missing comments. Signed-off-by: Srinivas Pandruvada Signed-off-by: Jiri Kosina --- include/linux/hid-sensor-hub.h | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/include/linux/hid-sensor-hub.h b/include/linux/hid-sensor-hub.h index 51f7ccadf923..4173a8fdad9e 100644 --- a/include/linux/hid-sensor-hub.h +++ b/include/linux/hid-sensor-hub.h @@ -33,6 +33,8 @@ * @units: Measurment unit for this attribute. * @unit_expo: Exponent used in the data. * @size: Size in bytes for data size. + * @logical_minimum: Logical minimum value for this attribute. + * @logical_maximum: Logical maximum value for this attribute. */ struct hid_sensor_hub_attribute_info { u32 usage_id; @@ -146,6 +148,7 @@ int sensor_hub_input_get_attribute_info(struct hid_sensor_hub_device *hsdev, /** * sensor_hub_input_attr_get_raw_value() - Synchronous read request +* @hsdev: Hub device instance. * @usage_id: Attribute usage id of parent physical device as per spec * @attr_usage_id: Attribute usage id as per spec * @report_id: Report id to look for @@ -160,6 +163,7 @@ int sensor_hub_input_attr_get_raw_value(struct hid_sensor_hub_device *hsdev, u32 attr_usage_id, u32 report_id); /** * sensor_hub_set_feature() - Feature set request +* @hsdev: Hub device instance. * @report_id: Report id to look for * @field_index: Field index inside a report * @value: Value to set @@ -172,6 +176,7 @@ int sensor_hub_set_feature(struct hid_sensor_hub_device *hsdev, u32 report_id, /** * sensor_hub_get_feature() - Feature get request +* @hsdev: Hub device instance. * @report_id: Report id to look for * @field_index: Field index inside a report * @value: Place holder for return value -- cgit v1.2.3-59-g8ed1b From ed1197709504c3641cbad32843667539cc912ea1 Mon Sep 17 00:00:00 2001 From: Srinivas Pandruvada Date: Wed, 7 Jan 2015 10:14:44 -0800 Subject: HID: sensor-hub: correct dyn_callback_lock IRQ-safe change Commit 0ccf091d1fbc1f99bb7f93bff8cf346769a9b0cd ("HID: sensor-hub: make dyn_callback_lock IRQ-safe) was supposed to change locks in sensor_hub_get_callback(), but missed. Signed-off-by: Srinivas Pandruvada Signed-off-by: Jiri Kosina --- drivers/hid/hid-sensor-hub.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/hid/hid-sensor-hub.c b/drivers/hid/hid-sensor-hub.c index 6a58b6c723aa..e54ce1097e2c 100644 --- a/drivers/hid/hid-sensor-hub.c +++ b/drivers/hid/hid-sensor-hub.c @@ -135,8 +135,9 @@ static struct hid_sensor_hub_callbacks *sensor_hub_get_callback( { struct hid_sensor_hub_callbacks_list *callback; struct sensor_hub_data *pdata = hid_get_drvdata(hdev); + unsigned long flags; - spin_lock(&pdata->dyn_callback_lock); + spin_lock_irqsave(&pdata->dyn_callback_lock, flags); list_for_each_entry(callback, &pdata->dyn_callback_list, list) if (callback->usage_id == usage_id && (collection_index >= @@ -145,10 +146,11 @@ static struct hid_sensor_hub_callbacks *sensor_hub_get_callback( callback->hsdev->end_collection_index)) { *priv = callback->priv; *hsdev = callback->hsdev; - spin_unlock(&pdata->dyn_callback_lock); + spin_unlock_irqrestore(&pdata->dyn_callback_lock, + flags); return callback->usage_callback; } - spin_unlock(&pdata->dyn_callback_lock); + spin_unlock_irqrestore(&pdata->dyn_callback_lock, flags); return NULL; } -- cgit v1.2.3-59-g8ed1b From a1d1e9be5a1dafe0ddc2181a9201c2ae29c71eff Mon Sep 17 00:00:00 2001 From: David Ramos Date: Fri, 13 Feb 2015 13:11:51 -0800 Subject: svcrpc: fix memory leak in gssp_accept_sec_context_upcall MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Our UC-KLEE tool found a kernel memory leak of 512 bytes (on x86_64) for each call to gssp_accept_sec_context_upcall() (net/sunrpc/auth_gss/gss_rpc_upcall.c). Since it appears that this call can be triggered by remote connections (at least, from a cursory a glance at the call chain), it may be exploitable to cause kernel memory exhaustion. We found the bug in kernel 3.16.3, but it appears to date back to commit 9dfd87da1aeb0fd364167ad199f40fe96a6a87be (2013-08-20). The gssp_accept_sec_context_upcall() function performs a pair of calls to gssp_alloc_receive_pages() and gssp_free_receive_pages(). The first allocates memory for arg->pages. The second then frees the pages pointed to by the arg->pages array, but not the array itself. Reported-by: David A. Ramos Fixes: 9dfd87da1aeb ("rpc: fix huge kmalloc's in gss-proxy”) Signed-off-by: David A. Ramos Signed-off-by: J. Bruce Fields --- net/sunrpc/auth_gss/gss_rpc_upcall.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/sunrpc/auth_gss/gss_rpc_upcall.c b/net/sunrpc/auth_gss/gss_rpc_upcall.c index abbb7dcd1689..59eeed43eda2 100644 --- a/net/sunrpc/auth_gss/gss_rpc_upcall.c +++ b/net/sunrpc/auth_gss/gss_rpc_upcall.c @@ -217,6 +217,8 @@ static void gssp_free_receive_pages(struct gssx_arg_accept_sec_context *arg) for (i = 0; i < arg->npages && arg->pages[i]; i++) __free_page(arg->pages[i]); + + kfree(arg->pages); } static int gssp_alloc_receive_pages(struct gssx_arg_accept_sec_context *arg) -- cgit v1.2.3-59-g8ed1b From ce204e9a4bd82e9e6e7479bca8057e45aaac5c42 Mon Sep 17 00:00:00 2001 From: Ivan Khoronzhuk Date: Wed, 18 Feb 2015 15:51:41 +0200 Subject: firmware: dmi_scan: Fix dmi scan to handle "End of Table" structure The dmi-sysfs should create "End of Table" entry, that is type 127. But after adding initial SMBIOS v3 support fc43026278b2 ("dmi: add support for SMBIOS 3.0 64-bit entry point") the 127-0 entry is not handled any more, as result it's not created in dmi sysfs for instance. This is important because the size of whole DMI table must correspond to sum of all DMI entry sizes. So move the end-of-table check after it's handled by dmi_table. Reviewed-by: Ard Biesheuvel Signed-off-by: Ivan Khoronzhuk Cc: # v3.19 Signed-off-by: Matt Fleming --- drivers/firmware/dmi_scan.c | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-) diff --git a/drivers/firmware/dmi_scan.c b/drivers/firmware/dmi_scan.c index c5f7b4e9eb6c..a44b87c7b45c 100644 --- a/drivers/firmware/dmi_scan.c +++ b/drivers/firmware/dmi_scan.c @@ -92,12 +92,6 @@ static void dmi_table(u8 *buf, int len, int num, while ((i < num) && (data - buf + sizeof(struct dmi_header)) <= len) { const struct dmi_header *dm = (const struct dmi_header *)data; - /* - * 7.45 End-of-Table (Type 127) [SMBIOS reference spec v3.0.0] - */ - if (dm->type == DMI_ENTRY_END_OF_TABLE) - break; - /* * We want to know the total length (formatted area and * strings) before decoding to make sure we won't run off the @@ -108,6 +102,13 @@ static void dmi_table(u8 *buf, int len, int num, data++; if (data - buf < len - 1) decode(dm, private_data); + + /* + * 7.45 End-of-Table (Type 127) [SMBIOS reference spec v3.0.0] + */ + if (dm->type == DMI_ENTRY_END_OF_TABLE) + break; + data += 2; i++; } -- cgit v1.2.3-59-g8ed1b From 6c40065fc107cae29ab965f162406fcfd1525f1d Mon Sep 17 00:00:00 2001 From: Antonio Ospite Date: Mon, 16 Feb 2015 22:58:24 +0100 Subject: HID: sony: Fix a WARNING shown when rmmod-ing the driver ida_destroy() must be called _after_ all the devices have been unregistered; otherwise, when calling "rmmod hid_sony" with devices still plugged in, the following warning would show up because of calls to ida_simple_remove() on a destroyed ID allocator: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 5509 at lib/idr.c:1052 ida_simple_remove+0x26/0x50() ida_remove called for id=0 which is not allocated. Modules linked in: ... CPU: 0 PID: 5509 Comm: rmmod Not tainted 3.19.0-rc6-ao2 #35 Hardware name: System manufacturer System Product Name/M2N-MX SE, BIOS 0501 03/20/2008 0000000000000000 ffffffff8176320d ffffffff815b3a88 ffff880036f7fdd8 ffffffff8106ce01 0000000000000000 ffffffffa07658e0 0000000000000246 ffff88005077d8b8 ffff88005077d8d0 ffffffff8106ce7a ffffffff81763260 Call Trace: [] ? dump_stack+0x40/0x50 [] ? warn_slowpath_common+0x81/0xb0 [] ? warn_slowpath_fmt+0x4a/0x50 [] ? ida_simple_remove+0x26/0x50 [] ? sony_remove+0x58/0xe0 [hid_sony] [] ? hid_device_remove+0x65/0xd0 [hid] [] ? __device_release_driver+0x7e/0x100 [] ? driver_detach+0xa0/0xb0 [] ? bus_remove_driver+0x55/0xe0 [] ? hid_unregister_driver+0x2f/0xa0 [hid] [] ? SyS_delete_module+0x1bf/0x270 [] ? do_notify_resume+0x69/0xa0 [] ? system_call_fastpath+0x16/0x1b ---[ end trace bc794b3d22c30ede ]--- Signed-off-by: Antonio Ospite Acked-by: Frank Praznik Signed-off-by: Jiri Kosina --- drivers/hid/hid-sony.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hid/hid-sony.c b/drivers/hid/hid-sony.c index 31e9d2561106..38d8af558d72 100644 --- a/drivers/hid/hid-sony.c +++ b/drivers/hid/hid-sony.c @@ -2147,8 +2147,8 @@ static void __exit sony_exit(void) { dbg_hid("Sony:%s\n", __func__); - ida_destroy(&sony_device_id_allocator); hid_unregister_driver(&sony_driver); + ida_destroy(&sony_device_id_allocator); } module_init(sony_init); module_exit(sony_exit); -- cgit v1.2.3-59-g8ed1b From b0bd96fe9a1428a04c82f8c3834db69468869d65 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 19 Feb 2015 12:30:49 +1030 Subject: lguest: now depends on PCI Reported-by: Randy Dunlap Signed-off-by: Rusty Russell --- arch/x86/lguest/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/lguest/Kconfig b/arch/x86/lguest/Kconfig index 4a0890f815c4..21e89807244c 100644 --- a/arch/x86/lguest/Kconfig +++ b/arch/x86/lguest/Kconfig @@ -1,6 +1,6 @@ config LGUEST_GUEST bool "Lguest guest support" - depends on X86_32 && PARAVIRT + depends on X86_32 && PARAVIRT && PCI select TTY select VIRTUALIZATION select VIRTIO -- cgit v1.2.3-59-g8ed1b From f476893459318cb2eff3ecd2a05d4ceacf82e73e Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 19 Feb 2015 14:43:21 +1030 Subject: lguest: update help text. We now add about 10k, not 6k, when lguest support is compiled in. Signed-off-by: Rusty Russell --- arch/x86/lguest/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/lguest/Kconfig b/arch/x86/lguest/Kconfig index 21e89807244c..08f41caada45 100644 --- a/arch/x86/lguest/Kconfig +++ b/arch/x86/lguest/Kconfig @@ -8,7 +8,7 @@ config LGUEST_GUEST help Lguest is a tiny in-kernel hypervisor. Selecting this will allow your kernel to boot under lguest. This option will increase - your kernel size by about 6k. If in doubt, say N. + your kernel size by about 10k. If in doubt, say N. If you say Y here, make sure you say Y (or M) to the virtio block and net drivers which lguest needs. -- cgit v1.2.3-59-g8ed1b From c03bf1bfd3a5448a4474f02b839f2195e3719cd9 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Wed, 18 Feb 2015 10:34:08 +0100 Subject: drm/tegra: hdmi: Explicitly set clock rate Recent changes in the clock framework have caused a behavioural change in that clocks that have not had their rate set explicitly will now be reset to their initial rate (or 0) when the clock is released. This is triggered in the deferred probing path, resulting in the clock running at a wrong frequency after the successful probe. This can be easily fixed by setting the rate explicitly rather than by relying on the implicit rate inherited by the parent. Tested-by: Tomeu Vizoso Signed-off-by: Thierry Reding --- drivers/gpu/drm/tegra/hdmi.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/gpu/drm/tegra/hdmi.c b/drivers/gpu/drm/tegra/hdmi.c index 7e06657ae58b..7eaaee74a039 100644 --- a/drivers/gpu/drm/tegra/hdmi.c +++ b/drivers/gpu/drm/tegra/hdmi.c @@ -851,6 +851,14 @@ static void tegra_hdmi_encoder_mode_set(struct drm_encoder *encoder, h_back_porch = mode->htotal - mode->hsync_end; h_front_porch = mode->hsync_start - mode->hdisplay; + err = clk_set_rate(hdmi->clk, pclk); + if (err < 0) { + dev_err(hdmi->dev, "failed to set HDMI clock frequency: %d\n", + err); + } + + DRM_DEBUG_KMS("HDMI clock rate: %lu Hz\n", clk_get_rate(hdmi->clk)); + /* power up sequence */ value = tegra_hdmi_readl(hdmi, HDMI_NV_PDISP_SOR_PLL0); value &= ~SOR_PLL_PDBG; -- cgit v1.2.3-59-g8ed1b From 567a3cd1d75e3f282759af3bd05a7369daef2b2a Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Thu, 19 Feb 2015 12:35:56 +0100 Subject: drm/tegra: dc: Reset state's active_changed field Commit eab3bbeffd15 ("drm/atomic: Add drm_crtc_state->active") added the field to track the DPMS state. However, the Tegra driver was in modified in parallel and subclasses the CRTC atomic state, so needed to duplicate the code in the atomic helpers. After the addition of the active_changed field it became out of sync and doesn't reset it when duplicating state. This causes a full modeset on things like page-flips, which will in turn cause warnings due to the VBLANK machinery being disabled when it really should remain on. Tested-by: Tomeu Vizoso Signed-off-by: Thierry Reding --- drivers/gpu/drm/tegra/dc.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/gpu/drm/tegra/dc.c b/drivers/gpu/drm/tegra/dc.c index 3aaa84ae2681..ec84bd486561 100644 --- a/drivers/gpu/drm/tegra/dc.c +++ b/drivers/gpu/drm/tegra/dc.c @@ -1012,6 +1012,7 @@ tegra_crtc_atomic_duplicate_state(struct drm_crtc *crtc) return NULL; copy->base.mode_changed = false; + copy->base.active_changed = false; copy->base.planes_changed = false; copy->base.event = NULL; -- cgit v1.2.3-59-g8ed1b From 332bbe7003badae01fed55b11820fcd467b3bbf4 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Wed, 28 Jan 2015 15:03:31 +0100 Subject: drm/tegra: dc: Wire up CRTC parent of atomic state Store a pointer to the CRTC in its atomic state to make it easy for state handling code to get at the CRTC. Tested-by: Tomeu Vizoso Signed-off-by: Thierry Reding --- drivers/gpu/drm/tegra/dc.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/tegra/dc.c b/drivers/gpu/drm/tegra/dc.c index ec84bd486561..2fd229366bb2 100644 --- a/drivers/gpu/drm/tegra/dc.c +++ b/drivers/gpu/drm/tegra/dc.c @@ -997,8 +997,10 @@ static void tegra_crtc_reset(struct drm_crtc *crtc) crtc->state = NULL; state = kzalloc(sizeof(*state), GFP_KERNEL); - if (state) + if (state) { crtc->state = &state->base; + crtc->state->crtc = crtc; + } } static struct drm_crtc_state * -- cgit v1.2.3-59-g8ed1b From 07d05cbf60ed8f06c61484d3d85c06c1aa7edf38 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Wed, 28 Jan 2015 15:17:44 +0100 Subject: drm/tegra: dc: Move more code into ->init() The code in tegra_crtc_prepare() really belongs in tegra_dc_init(), or at least most of it. This fixes an issue with VBLANK handling because tegra_crtc_prepare() would overwrite the interrupt mask register that tegra_crtc_enable_vblank() had written to to enable VBLANK interrupts. Tested-by: Tomeu Vizoso Signed-off-by: Thierry Reding --- drivers/gpu/drm/tegra/dc.c | 74 ++++++++++++++++++++++------------------------ 1 file changed, 36 insertions(+), 38 deletions(-) diff --git a/drivers/gpu/drm/tegra/dc.c b/drivers/gpu/drm/tegra/dc.c index 2fd229366bb2..1a52522f5da7 100644 --- a/drivers/gpu/drm/tegra/dc.c +++ b/drivers/gpu/drm/tegra/dc.c @@ -1230,9 +1230,6 @@ static void tegra_crtc_mode_set_nofb(struct drm_crtc *crtc) /* program display mode */ tegra_dc_set_timings(dc, mode); - if (dc->soc->supports_border_color) - tegra_dc_writel(dc, 0, DC_DISP_BORDER_COLOR); - /* interlacing isn't supported yet, so disable it */ if (dc->soc->supports_interlacing) { value = tegra_dc_readl(dc, DC_DISP_INTERLACE_CONTROL); @@ -1255,42 +1252,7 @@ static void tegra_crtc_mode_set_nofb(struct drm_crtc *crtc) static void tegra_crtc_prepare(struct drm_crtc *crtc) { - struct tegra_dc *dc = to_tegra_dc(crtc); - unsigned int syncpt; - unsigned long value; - drm_crtc_vblank_off(crtc); - - if (dc->pipe) - syncpt = SYNCPT_VBLANK1; - else - syncpt = SYNCPT_VBLANK0; - - /* initialize display controller */ - tegra_dc_writel(dc, 0x00000100, DC_CMD_GENERAL_INCR_SYNCPT_CNTRL); - tegra_dc_writel(dc, 0x100 | syncpt, DC_CMD_CONT_SYNCPT_VSYNC); - - value = WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT | WIN_A_OF_INT; - tegra_dc_writel(dc, value, DC_CMD_INT_TYPE); - - value = WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT | - WIN_A_OF_INT | WIN_B_OF_INT | WIN_C_OF_INT; - tegra_dc_writel(dc, value, DC_CMD_INT_POLARITY); - - /* initialize timer */ - value = CURSOR_THRESHOLD(0) | WINDOW_A_THRESHOLD(0x20) | - WINDOW_B_THRESHOLD(0x20) | WINDOW_C_THRESHOLD(0x20); - tegra_dc_writel(dc, value, DC_DISP_DISP_MEM_HIGH_PRIORITY); - - value = CURSOR_THRESHOLD(0) | WINDOW_A_THRESHOLD(1) | - WINDOW_B_THRESHOLD(1) | WINDOW_C_THRESHOLD(1); - tegra_dc_writel(dc, value, DC_DISP_DISP_MEM_HIGH_PRIORITY_TIMER); - - value = VBLANK_INT | WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT; - tegra_dc_writel(dc, value, DC_CMD_INT_ENABLE); - - value = WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT; - tegra_dc_writel(dc, value, DC_CMD_INT_MASK); } static void tegra_crtc_commit(struct drm_crtc *crtc) @@ -1667,6 +1629,8 @@ static int tegra_dc_init(struct host1x_client *client) struct tegra_drm *tegra = drm->dev_private; struct drm_plane *primary = NULL; struct drm_plane *cursor = NULL; + unsigned int syncpt; + u32 value; int err; if (tegra->domain) { @@ -1733,6 +1697,40 @@ static int tegra_dc_init(struct host1x_client *client) goto cleanup; } + /* initialize display controller */ + if (dc->pipe) + syncpt = SYNCPT_VBLANK1; + else + syncpt = SYNCPT_VBLANK0; + + tegra_dc_writel(dc, 0x00000100, DC_CMD_GENERAL_INCR_SYNCPT_CNTRL); + tegra_dc_writel(dc, 0x100 | syncpt, DC_CMD_CONT_SYNCPT_VSYNC); + + value = WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT | WIN_A_OF_INT; + tegra_dc_writel(dc, value, DC_CMD_INT_TYPE); + + value = WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT | + WIN_A_OF_INT | WIN_B_OF_INT | WIN_C_OF_INT; + tegra_dc_writel(dc, value, DC_CMD_INT_POLARITY); + + /* initialize timer */ + value = CURSOR_THRESHOLD(0) | WINDOW_A_THRESHOLD(0x20) | + WINDOW_B_THRESHOLD(0x20) | WINDOW_C_THRESHOLD(0x20); + tegra_dc_writel(dc, value, DC_DISP_DISP_MEM_HIGH_PRIORITY); + + value = CURSOR_THRESHOLD(0) | WINDOW_A_THRESHOLD(1) | + WINDOW_B_THRESHOLD(1) | WINDOW_C_THRESHOLD(1); + tegra_dc_writel(dc, value, DC_DISP_DISP_MEM_HIGH_PRIORITY_TIMER); + + value = VBLANK_INT | WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT; + tegra_dc_writel(dc, value, DC_CMD_INT_ENABLE); + + value = WIN_A_UF_INT | WIN_B_UF_INT | WIN_C_UF_INT; + tegra_dc_writel(dc, value, DC_CMD_INT_MASK); + + if (dc->soc->supports_border_color) + tegra_dc_writel(dc, 0, DC_DISP_BORDER_COLOR); + return 0; cleanup: -- cgit v1.2.3-59-g8ed1b From 1c4cff0cf55011792125b6041bc4e9713e46240f Mon Sep 17 00:00:00 2001 From: Ignacy Gawędzki Date: Fri, 13 Feb 2015 14:47:05 -0800 Subject: gen_stats.c: Duplicate xstats buffer for later use MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The gnet_stats_copy_app() function gets called, more often than not, with its second argument a pointer to an automatic variable in the caller's stack. Therefore, to avoid copying garbage afterwards when calling gnet_stats_finish_copy(), this data is better copied to a dynamically allocated memory that gets freed after use. [xiyou.wangcong@gmail.com: remove a useless kfree()] Signed-off-by: Ignacy Gawędzki Signed-off-by: Cong Wang Signed-off-by: David S. Miller --- net/core/gen_stats.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) diff --git a/net/core/gen_stats.c b/net/core/gen_stats.c index 0c08062d1796..1e2f46a69d50 100644 --- a/net/core/gen_stats.c +++ b/net/core/gen_stats.c @@ -32,6 +32,9 @@ gnet_stats_copy(struct gnet_dump *d, int type, void *buf, int size) return 0; nla_put_failure: + kfree(d->xstats); + d->xstats = NULL; + d->xstats_len = 0; spin_unlock_bh(d->lock); return -1; } @@ -305,7 +308,9 @@ int gnet_stats_copy_app(struct gnet_dump *d, void *st, int len) { if (d->compat_xstats) { - d->xstats = st; + d->xstats = kmemdup(st, len, GFP_ATOMIC); + if (!d->xstats) + goto err_out; d->xstats_len = len; } @@ -313,6 +318,11 @@ gnet_stats_copy_app(struct gnet_dump *d, void *st, int len) return gnet_stats_copy(d, TCA_STATS_APP, st, len); return 0; + +err_out: + d->xstats_len = 0; + spin_unlock_bh(d->lock); + return -1; } EXPORT_SYMBOL(gnet_stats_copy_app); @@ -345,6 +355,9 @@ gnet_stats_finish_copy(struct gnet_dump *d) return -1; } + kfree(d->xstats); + d->xstats = NULL; + d->xstats_len = 0; spin_unlock_bh(d->lock); return 0; } -- cgit v1.2.3-59-g8ed1b From aa183323312dbd1457096b4b94ca274b35fc462b Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Sun, 15 Feb 2015 17:44:20 -0200 Subject: ehea: Register memory hotplug, reboot and crash hooks on adapter probe ehea creates memory hotplug, reboot and crash hooks even if there are no adapters in the box. Just create them when we probe our first adapter. [cascardo: use ehea_register_memory_hooks return code] Signed-off-by: Anton Blanchard Tested-by: Thadeu Lima de Souza Cascardo Signed-off-by: Thadeu Lima de Souza Cascardo Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/ehea/ehea_main.c | 246 +++++++++++++++++------------- 1 file changed, 141 insertions(+), 105 deletions(-) diff --git a/drivers/net/ethernet/ibm/ehea/ehea_main.c b/drivers/net/ethernet/ibm/ehea/ehea_main.c index e8a1adb7a962..c05e50759621 100644 --- a/drivers/net/ethernet/ibm/ehea/ehea_main.c +++ b/drivers/net/ethernet/ibm/ehea/ehea_main.c @@ -3262,6 +3262,139 @@ static void ehea_remove_device_sysfs(struct platform_device *dev) device_remove_file(&dev->dev, &dev_attr_remove_port); } +static int ehea_reboot_notifier(struct notifier_block *nb, + unsigned long action, void *unused) +{ + if (action == SYS_RESTART) { + pr_info("Reboot: freeing all eHEA resources\n"); + ibmebus_unregister_driver(&ehea_driver); + } + return NOTIFY_DONE; +} + +static struct notifier_block ehea_reboot_nb = { + .notifier_call = ehea_reboot_notifier, +}; + +static int ehea_mem_notifier(struct notifier_block *nb, + unsigned long action, void *data) +{ + int ret = NOTIFY_BAD; + struct memory_notify *arg = data; + + mutex_lock(&dlpar_mem_lock); + + switch (action) { + case MEM_CANCEL_OFFLINE: + pr_info("memory offlining canceled"); + /* Fall through: re-add canceled memory block */ + + case MEM_ONLINE: + pr_info("memory is going online"); + set_bit(__EHEA_STOP_XFER, &ehea_driver_flags); + if (ehea_add_sect_bmap(arg->start_pfn, arg->nr_pages)) + goto out_unlock; + ehea_rereg_mrs(); + break; + + case MEM_GOING_OFFLINE: + pr_info("memory is going offline"); + set_bit(__EHEA_STOP_XFER, &ehea_driver_flags); + if (ehea_rem_sect_bmap(arg->start_pfn, arg->nr_pages)) + goto out_unlock; + ehea_rereg_mrs(); + break; + + default: + break; + } + + ehea_update_firmware_handles(); + ret = NOTIFY_OK; + +out_unlock: + mutex_unlock(&dlpar_mem_lock); + return ret; +} + +static struct notifier_block ehea_mem_nb = { + .notifier_call = ehea_mem_notifier, +}; + +static void ehea_crash_handler(void) +{ + int i; + + if (ehea_fw_handles.arr) + for (i = 0; i < ehea_fw_handles.num_entries; i++) + ehea_h_free_resource(ehea_fw_handles.arr[i].adh, + ehea_fw_handles.arr[i].fwh, + FORCE_FREE); + + if (ehea_bcmc_regs.arr) + for (i = 0; i < ehea_bcmc_regs.num_entries; i++) + ehea_h_reg_dereg_bcmc(ehea_bcmc_regs.arr[i].adh, + ehea_bcmc_regs.arr[i].port_id, + ehea_bcmc_regs.arr[i].reg_type, + ehea_bcmc_regs.arr[i].macaddr, + 0, H_DEREG_BCMC); +} + +static atomic_t ehea_memory_hooks_registered; + +/* Register memory hooks on probe of first adapter */ +static int ehea_register_memory_hooks(void) +{ + int ret = 0; + + if (atomic_inc_and_test(&ehea_memory_hooks_registered)) + return 0; + + ret = ehea_create_busmap(); + if (ret) { + pr_info("ehea_create_busmap failed\n"); + goto out; + } + + ret = register_reboot_notifier(&ehea_reboot_nb); + if (ret) { + pr_info("register_reboot_notifier failed\n"); + goto out; + } + + ret = register_memory_notifier(&ehea_mem_nb); + if (ret) { + pr_info("register_memory_notifier failed\n"); + goto out2; + } + + ret = crash_shutdown_register(ehea_crash_handler); + if (ret) { + pr_info("crash_shutdown_register failed\n"); + goto out3; + } + + return 0; + +out3: + unregister_memory_notifier(&ehea_mem_nb); +out2: + unregister_reboot_notifier(&ehea_reboot_nb); +out: + return ret; +} + +static void ehea_unregister_memory_hooks(void) +{ + if (atomic_read(&ehea_memory_hooks_registered)) + return; + + unregister_reboot_notifier(&ehea_reboot_nb); + if (crash_shutdown_unregister(ehea_crash_handler)) + pr_info("failed unregistering crash handler\n"); + unregister_memory_notifier(&ehea_mem_nb); +} + static int ehea_probe_adapter(struct platform_device *dev) { struct ehea_adapter *adapter; @@ -3269,6 +3402,10 @@ static int ehea_probe_adapter(struct platform_device *dev) int ret; int i; + ret = ehea_register_memory_hooks(); + if (ret) + return ret; + if (!dev || !dev->dev.of_node) { pr_err("Invalid ibmebus device probed\n"); return -EINVAL; @@ -3392,81 +3529,6 @@ static int ehea_remove(struct platform_device *dev) return 0; } -static void ehea_crash_handler(void) -{ - int i; - - if (ehea_fw_handles.arr) - for (i = 0; i < ehea_fw_handles.num_entries; i++) - ehea_h_free_resource(ehea_fw_handles.arr[i].adh, - ehea_fw_handles.arr[i].fwh, - FORCE_FREE); - - if (ehea_bcmc_regs.arr) - for (i = 0; i < ehea_bcmc_regs.num_entries; i++) - ehea_h_reg_dereg_bcmc(ehea_bcmc_regs.arr[i].adh, - ehea_bcmc_regs.arr[i].port_id, - ehea_bcmc_regs.arr[i].reg_type, - ehea_bcmc_regs.arr[i].macaddr, - 0, H_DEREG_BCMC); -} - -static int ehea_mem_notifier(struct notifier_block *nb, - unsigned long action, void *data) -{ - int ret = NOTIFY_BAD; - struct memory_notify *arg = data; - - mutex_lock(&dlpar_mem_lock); - - switch (action) { - case MEM_CANCEL_OFFLINE: - pr_info("memory offlining canceled"); - /* Readd canceled memory block */ - case MEM_ONLINE: - pr_info("memory is going online"); - set_bit(__EHEA_STOP_XFER, &ehea_driver_flags); - if (ehea_add_sect_bmap(arg->start_pfn, arg->nr_pages)) - goto out_unlock; - ehea_rereg_mrs(); - break; - case MEM_GOING_OFFLINE: - pr_info("memory is going offline"); - set_bit(__EHEA_STOP_XFER, &ehea_driver_flags); - if (ehea_rem_sect_bmap(arg->start_pfn, arg->nr_pages)) - goto out_unlock; - ehea_rereg_mrs(); - break; - default: - break; - } - - ehea_update_firmware_handles(); - ret = NOTIFY_OK; - -out_unlock: - mutex_unlock(&dlpar_mem_lock); - return ret; -} - -static struct notifier_block ehea_mem_nb = { - .notifier_call = ehea_mem_notifier, -}; - -static int ehea_reboot_notifier(struct notifier_block *nb, - unsigned long action, void *unused) -{ - if (action == SYS_RESTART) { - pr_info("Reboot: freeing all eHEA resources\n"); - ibmebus_unregister_driver(&ehea_driver); - } - return NOTIFY_DONE; -} - -static struct notifier_block ehea_reboot_nb = { - .notifier_call = ehea_reboot_notifier, -}; - static int check_module_parm(void) { int ret = 0; @@ -3520,26 +3582,10 @@ static int __init ehea_module_init(void) if (ret) goto out; - ret = ehea_create_busmap(); - if (ret) - goto out; - - ret = register_reboot_notifier(&ehea_reboot_nb); - if (ret) - pr_info("failed registering reboot notifier\n"); - - ret = register_memory_notifier(&ehea_mem_nb); - if (ret) - pr_info("failed registering memory remove notifier\n"); - - ret = crash_shutdown_register(ehea_crash_handler); - if (ret) - pr_info("failed registering crash handler\n"); - ret = ibmebus_register_driver(&ehea_driver); if (ret) { pr_err("failed registering eHEA device driver on ebus\n"); - goto out2; + goto out; } ret = driver_create_file(&ehea_driver.driver, @@ -3547,32 +3593,22 @@ static int __init ehea_module_init(void) if (ret) { pr_err("failed to register capabilities attribute, ret=%d\n", ret); - goto out3; + goto out2; } return ret; -out3: - ibmebus_unregister_driver(&ehea_driver); out2: - unregister_memory_notifier(&ehea_mem_nb); - unregister_reboot_notifier(&ehea_reboot_nb); - crash_shutdown_unregister(ehea_crash_handler); + ibmebus_unregister_driver(&ehea_driver); out: return ret; } static void __exit ehea_module_exit(void) { - int ret; - driver_remove_file(&ehea_driver.driver, &driver_attr_capabilities); ibmebus_unregister_driver(&ehea_driver); - unregister_reboot_notifier(&ehea_reboot_nb); - ret = crash_shutdown_unregister(ehea_crash_handler); - if (ret) - pr_info("failed unregistering crash handler\n"); - unregister_memory_notifier(&ehea_mem_nb); + ehea_unregister_memory_hooks(); kfree(ehea_fw_handles.arr); kfree(ehea_bcmc_regs.arr); ehea_destroy_busmap(); -- cgit v1.2.3-59-g8ed1b From e57cf21e9787c081db4db6afa02e6e70112ee410 Mon Sep 17 00:00:00 2001 From: Chris Mason Date: Thu, 19 Feb 2015 17:51:39 -0800 Subject: Btrfs: fix allocation size calculations in alloc_btrfs_bio Since commit 8e5cfb55d3f (Btrfs: Make raid_map array be inlined in btrfs_bio structure), the raid map array is allocated along with the btrfs bio in alloc_btrfs_bio. The calculation used to decide how much we need to allocate was using the wrong parameter passed into the allocation function. The passed in real_stripes will be zero if a target replace operation is not currently running. We want to use total_stripes instead. Signed-off-by: Chris Mason Reported-by: David Sterba Tested-by: David Sterba --- fs/btrfs/volumes.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c index cd4d1315aaa9..8222f6f74147 100644 --- a/fs/btrfs/volumes.c +++ b/fs/btrfs/volumes.c @@ -4903,10 +4903,17 @@ static void sort_parity_stripes(struct btrfs_bio *bbio, int num_stripes) static struct btrfs_bio *alloc_btrfs_bio(int total_stripes, int real_stripes) { struct btrfs_bio *bbio = kzalloc( + /* the size of the btrfs_bio */ sizeof(struct btrfs_bio) + + /* plus the variable array for the stripes */ sizeof(struct btrfs_bio_stripe) * (total_stripes) + + /* plus the variable array for the tgt dev */ sizeof(int) * (real_stripes) + - sizeof(u64) * (real_stripes), + /* + * plus the raid_map, which includes both the tgt dev + * and the stripes + */ + sizeof(u64) * (total_stripes), GFP_NOFS); if (!bbio) return NULL; -- cgit v1.2.3-59-g8ed1b From 42c972a1f390e3bc51ca1e434b7e28764992067f Mon Sep 17 00:00:00 2001 From: Ben Shelton Date: Mon, 16 Feb 2015 13:47:06 -0600 Subject: usb: plusb: Add support for National Instruments host-to-host cable The National Instruments USB Host-to-Host Cable is based on the Prolific PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it. Signed-off-by: Ben Shelton Signed-off-by: David S. Miller --- drivers/net/usb/plusb.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/net/usb/plusb.c b/drivers/net/usb/plusb.c index 3d18bb0eee85..1bfe0fcaccf5 100644 --- a/drivers/net/usb/plusb.c +++ b/drivers/net/usb/plusb.c @@ -134,6 +134,11 @@ static const struct usb_device_id products [] = { }, { USB_DEVICE(0x050d, 0x258a), /* Belkin F5U258/F5U279 (PL-25A1) */ .driver_info = (unsigned long) &prolific_info, +}, { + USB_DEVICE(0x3923, 0x7825), /* National Instruments USB + * Host-to-Host Cable + */ + .driver_info = (unsigned long) &prolific_info, }, { }, // END -- cgit v1.2.3-59-g8ed1b From fba04a9e0c869498889b6445fd06cbe7da9bb834 Mon Sep 17 00:00:00 2001 From: Alexander Drozdov Date: Tue, 17 Feb 2015 13:33:46 +0300 Subject: ipv4: ip_check_defrag should correctly check return value of skb_copy_bits skb_copy_bits() returns zero on success and negative value on error, so it is needed to invert the condition in ip_check_defrag(). Fixes: 1bf3751ec90c ("ipv4: ip_check_defrag must not modify skb before unsharing") Signed-off-by: Alexander Drozdov Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- net/ipv4/ip_fragment.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/ipv4/ip_fragment.c b/net/ipv4/ip_fragment.c index e5b6d0ddcb58..2c8d98e728c0 100644 --- a/net/ipv4/ip_fragment.c +++ b/net/ipv4/ip_fragment.c @@ -664,7 +664,7 @@ struct sk_buff *ip_check_defrag(struct sk_buff *skb, u32 user) if (skb->protocol != htons(ETH_P_IP)) return skb; - if (!skb_copy_bits(skb, 0, &iph, sizeof(iph))) + if (skb_copy_bits(skb, 0, &iph, sizeof(iph)) < 0) return skb; if (iph.ihl < 5 || iph.version != 4) -- cgit v1.2.3-59-g8ed1b From 54da5a8be3c1e924c35480eb44c6e9b275f6444e Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Tue, 17 Feb 2015 09:36:22 -0800 Subject: net: phy: Fix verification of EEE support in phy_init_eee phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex) to find a valid entry in the settings array for the given speed and duplex value. For full duplex 1000baseT, this will return the first matching entry, which is the entry for 1000baseKX_Full. If the phy eee does not support 1000baseKX_Full, this entry will not match, causing phy_init_eee to fail for no good reason. Fixes: 9a9c56cb34e6 ("net: phy: fix a bug when verify the EEE support") Fixes: 3e7077067e80c ("phy: Expand phy speed/duplex settings array") Cc: Giuseppe Cavallaro Signed-off-by: Guenter Roeck Acked-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/phy/phy.c | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-) diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index cdcac6aa4260..52cd8db2c57d 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -235,6 +235,25 @@ static inline unsigned int phy_find_valid(unsigned int idx, u32 features) return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; } +/** + * phy_check_valid - check if there is a valid PHY setting which matches + * speed, duplex, and feature mask + * @speed: speed to match + * @duplex: duplex to match + * @features: A mask of the valid settings + * + * Description: Returns true if there is a valid setting, false otherwise. + */ +static inline bool phy_check_valid(int speed, int duplex, u32 features) +{ + unsigned int idx; + + idx = phy_find_valid(phy_find_setting(speed, duplex), features); + + return settings[idx].speed == speed && settings[idx].duplex == duplex && + (settings[idx].setting & features); +} + /** * phy_sanitize_settings - make sure the PHY is set to supported speed and duplex * @phydev: the target phy_device struct @@ -1045,7 +1064,6 @@ int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable) int eee_lp, eee_cap, eee_adv; u32 lp, cap, adv; int status; - unsigned int idx; /* Read phy status to properly get the right settings */ status = phy_read_status(phydev); @@ -1077,8 +1095,7 @@ int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable) adv = mmd_eee_adv_to_ethtool_adv_t(eee_adv); lp = mmd_eee_adv_to_ethtool_adv_t(eee_lp); - idx = phy_find_setting(phydev->speed, phydev->duplex); - if (!(lp & adv & settings[idx].setting)) + if (!phy_check_valid(phydev->speed, phydev->duplex, lp & adv)) goto eee_exit_err; if (clk_stop_enable) { -- cgit v1.2.3-59-g8ed1b From 34eea79e2664b314cab6a30fc582fdfa7a1bb1df Mon Sep 17 00:00:00 2001 From: Ignacy Gawędzki Date: Tue, 17 Feb 2015 20:15:20 +0100 Subject: ematch: Fix auto-loading of ematch modules. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit In tcf_em_validate(), after calling request_module() to load the kind-specific module, set em->ops to NULL before returning -EAGAIN, so that module_put() is not called again by tcf_em_tree_destroy(). Signed-off-by: Ignacy Gawędzki Acked-by: Cong Wang Signed-off-by: David S. Miller --- net/sched/ematch.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/sched/ematch.c b/net/sched/ematch.c index 6742200b1307..fbb7ebfc58c6 100644 --- a/net/sched/ematch.c +++ b/net/sched/ematch.c @@ -228,6 +228,7 @@ static int tcf_em_validate(struct tcf_proto *tp, * to replay the request. */ module_put(em->ops->owner); + em->ops = NULL; err = -EAGAIN; } #endif -- cgit v1.2.3-59-g8ed1b From 7b4577a9da3702049650f7095506e9afd9f68849 Mon Sep 17 00:00:00 2001 From: Pravin B Shelar Date: Tue, 17 Feb 2015 11:23:10 -0800 Subject: openvswitch: Fix net exit. Open vSwitch allows moving internal vport to different namespace while still connected to the bridge. But when namespace deleted OVS does not detach these vports, that results in dangling pointer to netdevice which causes kernel panic as follows. This issue is fixed by detaching all ovs ports from the deleted namespace at net-exit. BUG: unable to handle kernel NULL pointer dereference at 0000000000000028 IP: [] ovs_vport_locate+0x35/0x80 [openvswitch] Oops: 0000 [#1] SMP Call Trace: [] lookup_vport+0x21/0xd0 [openvswitch] [] ovs_vport_cmd_get+0x59/0xf0 [openvswitch] [] genl_family_rcv_msg+0x1bc/0x3e0 [] genl_rcv_msg+0x79/0xc0 [] netlink_rcv_skb+0xb9/0xe0 [] genl_rcv+0x2c/0x40 [] netlink_unicast+0x12d/0x1c0 [] netlink_sendmsg+0x34a/0x6b0 [] sock_sendmsg+0xa0/0xe0 [] ___sys_sendmsg+0x408/0x420 [] __sys_sendmsg+0x51/0x90 [] SyS_sendmsg+0x12/0x20 [] system_call_fastpath+0x12/0x17 Reported-by: Assaf Muller Fixes: 46df7b81454("openvswitch: Add support for network namespaces.") Signed-off-by: Pravin B Shelar Reviewed-by: Thomas Graf Signed-off-by: David S. Miller --- net/openvswitch/datapath.c | 45 +++++++++++++++++++++++++++++++++++++++++++-- net/openvswitch/vport.h | 2 ++ 2 files changed, 45 insertions(+), 2 deletions(-) diff --git a/net/openvswitch/datapath.c b/net/openvswitch/datapath.c index ae5e77cdc0ca..5bae7243c577 100644 --- a/net/openvswitch/datapath.c +++ b/net/openvswitch/datapath.c @@ -2194,14 +2194,55 @@ static int __net_init ovs_init_net(struct net *net) return 0; } -static void __net_exit ovs_exit_net(struct net *net) +static void __net_exit list_vports_from_net(struct net *net, struct net *dnet, + struct list_head *head) { - struct datapath *dp, *dp_next; struct ovs_net *ovs_net = net_generic(net, ovs_net_id); + struct datapath *dp; + + list_for_each_entry(dp, &ovs_net->dps, list_node) { + int i; + + for (i = 0; i < DP_VPORT_HASH_BUCKETS; i++) { + struct vport *vport; + + hlist_for_each_entry(vport, &dp->ports[i], dp_hash_node) { + struct netdev_vport *netdev_vport; + + if (vport->ops->type != OVS_VPORT_TYPE_INTERNAL) + continue; + + netdev_vport = netdev_vport_priv(vport); + if (dev_net(netdev_vport->dev) == dnet) + list_add(&vport->detach_list, head); + } + } + } +} + +static void __net_exit ovs_exit_net(struct net *dnet) +{ + struct datapath *dp, *dp_next; + struct ovs_net *ovs_net = net_generic(dnet, ovs_net_id); + struct vport *vport, *vport_next; + struct net *net; + LIST_HEAD(head); ovs_lock(); list_for_each_entry_safe(dp, dp_next, &ovs_net->dps, list_node) __dp_destroy(dp); + + rtnl_lock(); + for_each_net(net) + list_vports_from_net(net, dnet, &head); + rtnl_unlock(); + + /* Detach all vports from given namespace. */ + list_for_each_entry_safe(vport, vport_next, &head, detach_list) { + list_del(&vport->detach_list); + ovs_dp_detach_port(vport); + } + ovs_unlock(); cancel_work_sync(&ovs_net->dp_notify_work); diff --git a/net/openvswitch/vport.h b/net/openvswitch/vport.h index f8ae295fb001..bc85331a6c60 100644 --- a/net/openvswitch/vport.h +++ b/net/openvswitch/vport.h @@ -103,6 +103,7 @@ struct vport_portids { * @ops: Class structure. * @percpu_stats: Points to per-CPU statistics used and maintained by vport * @err_stats: Points to error statistics used and maintained by vport + * @detach_list: list used for detaching vport in net-exit call. */ struct vport { struct rcu_head rcu; @@ -117,6 +118,7 @@ struct vport { struct pcpu_sw_netstats __percpu *percpu_stats; struct vport_err_stats err_stats; + struct list_head detach_list; }; /** -- cgit v1.2.3-59-g8ed1b From f81edc6ac1e1e2e2cbe98bcd6ef5ebb7afb00807 Mon Sep 17 00:00:00 2001 From: Derrick Pallas Date: Wed, 18 Feb 2015 00:50:25 -0800 Subject: ethernet/ixp4xx: prevent allmulti from clobbering promisc If both promisc and allmulti are set, promisc should trump allmulti and disable the MAC filter; otherwise, the interface is not really promisc. Previously, this code checked IFF_ALLMULTI prior to and without regard for IFF_PROMISC; if both were set, only multicast and direct unicast traffic would make it through the filter. Signed-off-by: Derrick Pallas Signed-off-by: David S. Miller --- drivers/net/ethernet/xscale/ixp4xx_eth.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/xscale/ixp4xx_eth.c b/drivers/net/ethernet/xscale/ixp4xx_eth.c index f7e0f0f7c2e2..9e16a2819d48 100644 --- a/drivers/net/ethernet/xscale/ixp4xx_eth.c +++ b/drivers/net/ethernet/xscale/ixp4xx_eth.c @@ -938,7 +938,7 @@ static void eth_set_mcast_list(struct net_device *dev) int i; static const u8 allmulti[] = { 0x01, 0x00, 0x00, 0x00, 0x00, 0x00 }; - if (dev->flags & IFF_ALLMULTI) { + if ((dev->flags & IFF_ALLMULTI) && !(dev->flags & IFF_PROMISC)) { for (i = 0; i < ETH_ALEN; i++) { __raw_writel(allmulti[i], &port->regs->mcast_addr[i]); __raw_writel(allmulti[i], &port->regs->mcast_mask[i]); -- cgit v1.2.3-59-g8ed1b From 846cd66788b11105a62785078360c8854aa98310 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Wed, 18 Feb 2015 11:38:06 +0100 Subject: net: Initialize all members in skb_gro_remcsum_init() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit skb_gro_remcsum_init() initializes the gro_remcsum.delta member only, leading to compiler warnings about a possibly uninitialized gro_remcsum.offset member: drivers/net/vxlan.c: In function ‘vxlan_gro_receive’: drivers/net/vxlan.c:602: warning: ‘grc.offset’ may be used uninitialized in this function net/ipv4/fou.c: In function ‘gue_gro_receive’: net/ipv4/fou.c:262: warning: ‘grc.offset’ may be used uninitialized in this function While these are harmless for now: - skb_gro_remcsum_process() sets offset before changing delta, - skb_gro_remcsum_cleanup() checks if delta is non-zero before accessing offset, it's safer to let the initialization function initialize all members. Signed-off-by: Geert Uytterhoeven Acked-by: Tom Herbert Signed-off-by: David S. Miller --- include/linux/netdevice.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 5897b4ea5a3f..429d1790a27e 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -2342,6 +2342,7 @@ struct gro_remcsum { static inline void skb_gro_remcsum_init(struct gro_remcsum *grc) { + grc->offset = 0; grc->delta = 0; } -- cgit v1.2.3-59-g8ed1b From 997d5c3f4427f38562cbe207ce05bb25fdcb993b Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Wed, 18 Feb 2015 05:47:55 -0800 Subject: sock: sock_dequeue_err_skb() needs hard irq safety Non NAPI drivers can call skb_tstamp_tx() and then sock_queue_err_skb() from hard IRQ context. Therefore, sock_dequeue_err_skb() needs to block hard irq or corruptions or hangs can happen. Signed-off-by: Eric Dumazet Fixes: 364a9e93243d1 ("sock: deduplicate errqueue dequeue") Fixes: cb820f8e4b7f7 ("net: Provide a generic socket error queue delivery method for Tx time stamps.") Signed-off-by: David S. Miller --- net/core/skbuff.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/net/core/skbuff.c b/net/core/skbuff.c index 88c613eab142..f80507823531 100644 --- a/net/core/skbuff.c +++ b/net/core/skbuff.c @@ -3621,13 +3621,14 @@ struct sk_buff *sock_dequeue_err_skb(struct sock *sk) { struct sk_buff_head *q = &sk->sk_error_queue; struct sk_buff *skb, *skb_next; + unsigned long flags; int err = 0; - spin_lock_bh(&q->lock); + spin_lock_irqsave(&q->lock, flags); skb = __skb_dequeue(q); if (skb && (skb_next = skb_peek(q))) err = SKB_EXT_ERR(skb_next)->ee.ee_errno; - spin_unlock_bh(&q->lock); + spin_unlock_irqrestore(&q->lock, flags); sk->sk_err = err; if (err) -- cgit v1.2.3-59-g8ed1b From 15added6a5940454e225c09b78837514d35fcf70 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 18 Feb 2015 20:47:30 +0100 Subject: net: smc91x: improve neponset hack The smc91x driver tries to support multiple platforms at compile time, but they are mutually exclusive at runtime, and not clearly defined. Trying to build for CONFIG_SA1100_ASSABET without CONFIG_ASSABET_NEPONSET results in this link error: drivers/built-in.o: In function `smc_drv_probe': :(.text+0x33310c): undefined reference to `neponset_ncr_frob' since the neponset_ncr_set function is not defined otherwise. Similarly, building for both CONFIG_SA1100_ASSABET and CONFIG_SA1100_PLEB results in a different build error: smsc/smc91x.c: In function 'smc_drv_probe': smsc/smc91x.c:2299:2: error: implicit declaration of function 'neponset_ncr_set' [-Werror=implicit-function-declaration] neponset_ncr_set(NCR_ENET_OSC_EN); ^ smsc/smc91x.c:2299:19: error: 'NCR_ENET_OSC_EN' undeclared (first use in this function) neponset_ncr_set(NCR_ENET_OSC_EN); ^ This is an attempt to fix the call site responsible for both errors, making sure we call the function exactly when the driver is actually trying to run on the assabet/neponset machine. With this patch, I no longer see randconfig build errors in this file. Signed-off-by: Arnd Bergmann Signed-off-by: David S. Miller --- drivers/net/ethernet/smsc/smc91x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/smsc/smc91x.c b/drivers/net/ethernet/smsc/smc91x.c index 88a55f95fe09..fa3f193b5f4d 100644 --- a/drivers/net/ethernet/smsc/smc91x.c +++ b/drivers/net/ethernet/smsc/smc91x.c @@ -2355,7 +2355,7 @@ static int smc_drv_probe(struct platform_device *pdev) ret = smc_request_attrib(pdev, ndev); if (ret) goto out_release_io; -#if defined(CONFIG_SA1100_ASSABET) +#if defined(CONFIG_ASSABET_NEPONSET) && !defined(CONFIG_SA1100_PLEB) neponset_ncr_set(NCR_ENET_OSC_EN); #endif platform_set_drvdata(pdev, ndev); -- cgit v1.2.3-59-g8ed1b From bf60e50cb3ed50ae536f7655c8af1acda137ea5b Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 18 Feb 2015 20:48:54 +0100 Subject: net/appletalk: LTPC needs virt_to_bus The ltpc driver is rather outdated and does not get built on most platforms because it requires the ISA_DMA_API symbol. However there are some ARM platforms that have ISA_DMA_API but no virt_to_bus, and they get this build error when enabling the ltpc driver. drivers/net/appletalk/ltpc.c: In function 'handlefc': drivers/net/appletalk/ltpc.c:380:2: error: implicit declaration of function 'virt_to_bus' [-Werror=implicit-function-declaration] set_dma_addr(dma,virt_to_bus(ltdmacbuf)); ^ This adds another dependency in Kconfig to avoid that configuration. Signed-off-by: Arnd Bergmann Signed-off-by: David S. Miller --- drivers/net/appletalk/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/appletalk/Kconfig b/drivers/net/appletalk/Kconfig index 4ce6ca5f3d36..dc6b78e5342f 100644 --- a/drivers/net/appletalk/Kconfig +++ b/drivers/net/appletalk/Kconfig @@ -40,7 +40,7 @@ config DEV_APPLETALK config LTPC tristate "Apple/Farallon LocalTalk PC support" - depends on DEV_APPLETALK && (ISA || EISA) && ISA_DMA_API + depends on DEV_APPLETALK && (ISA || EISA) && ISA_DMA_API && VIRT_TO_BUS help This allows you to use the AppleTalk PC card to connect to LocalTalk networks. The card is also known as the Farallon PhoneNet PC card. -- cgit v1.2.3-59-g8ed1b From b7f5e5c7f8cedf6b69c9702d448cdf78ffc45c7b Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Fri, 20 Feb 2015 21:14:21 +0100 Subject: rhashtable: don't allocate ht structure on stack in test_rht_init With object runtime debugging enabled, the rhashtable test suite will rightfully throw a warning "ODEBUG: object is on stack, but not annotated" from rhashtable_init(). This is because run_work is (correctly) being initialized via INIT_WORK(), and not annotated by INIT_WORK_ONSTACK(). Meaning, rhashtable_init() is okay as is, we just need to move ht e.g., into global scope. It never triggered anything, since test_rhashtable is rather a controlled environment and effectively runs to completion, so that stack memory is not vanishing underneath us, we shouldn't confuse any testers with it though. Fixes: 7e1e77636e36 ("lib: Resizable, Scalable, Concurrent Hash Table") Signed-off-by: Daniel Borkmann Acked-by: Thomas Graf Signed-off-by: David S. Miller --- lib/test_rhashtable.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/lib/test_rhashtable.c b/lib/test_rhashtable.c index 1dfeba73fc74..f6ce291b68e7 100644 --- a/lib/test_rhashtable.c +++ b/lib/test_rhashtable.c @@ -191,9 +191,10 @@ error: return err; } +static struct rhashtable ht; + static int __init test_rht_init(void) { - struct rhashtable ht; struct rhashtable_params params = { .nelem_hint = TEST_HT_SIZE, .head_offset = offsetof(struct test_obj, node), -- cgit v1.2.3-59-g8ed1b From f4c2b7a08170dc4e442c4566486e4597af8d72a3 Mon Sep 17 00:00:00 2001 From: Mahesh Bandewar Date: Wed, 18 Feb 2015 15:15:57 -0800 Subject: ipvlan: Fix text that talks about ip util support ipvlan was added into 3.19 release and iproute2 added support for the same in iproute2-3.19 package. Signed-off-by: Mahesh Bandewar CC: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 84673ebcf428..df51d6025a90 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -157,7 +157,7 @@ config IPVLAN making it transparent to the connected L2 switch. Ipvlan devices can be added using the "ip" command from the - iproute2 package starting with the iproute2-X.Y.ZZ release: + iproute2 package starting with the iproute2-3.19 release: "ip link add link [ NAME ] type ipvlan" -- cgit v1.2.3-59-g8ed1b From 65e9256c4ec569ed62bb89023daab7b72368b89f Mon Sep 17 00:00:00 2001 From: Rami Rosen Date: Fri, 20 Feb 2015 21:34:58 +0200 Subject: ethtool: Add hw-switch-offload to netdev_features_strings. commit aafb3e98b279 (netdev: introduce new NETIF_F_HW_SWITCH_OFFLOAD feature flag for switch device offloads) add a new feature without adding it to netdev_features_strings array; this patch fixes this. Signed-off-by: Rami Rosen Signed-off-by: David S. Miller --- net/core/ethtool.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/core/ethtool.c b/net/core/ethtool.c index 91f74f3eb204..aa378ecef186 100644 --- a/net/core/ethtool.c +++ b/net/core/ethtool.c @@ -98,6 +98,7 @@ static const char netdev_features_strings[NETDEV_FEATURE_COUNT][ETH_GSTRING_LEN] [NETIF_F_RXALL_BIT] = "rx-all", [NETIF_F_HW_L2FW_DOFFLOAD_BIT] = "l2-fwd-offload", [NETIF_F_BUSY_POLL_BIT] = "busy-poll", + [NETIF_F_HW_SWITCH_OFFLOAD_BIT] = "hw-switch-offload", }; static const char -- cgit v1.2.3-59-g8ed1b From 5a8eeec468f229558322926f28c61bb0769793e9 Mon Sep 17 00:00:00 2001 From: Anish Bhatt Date: Wed, 18 Feb 2015 15:29:45 -0800 Subject: cxgb4: Fix incorrect 'c' suffix to %pI4, use %pISc instead Issue caught by 0-day kernel test infrastructure. Code changed to use sockaddr members so that %pISc can be used instead. Fixes: b5a02f503caa ('cxgb4 : Update ipv6 address handling api') Signed-off-by: Anish Bhatt Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/clip_tbl.c | 57 ++++++++++++++------------- drivers/net/ethernet/chelsio/cxgb4/clip_tbl.h | 6 ++- 2 files changed, 33 insertions(+), 30 deletions(-) diff --git a/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.c b/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.c index 9062a8434246..c308429dd9c7 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.c +++ b/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.c @@ -35,10 +35,10 @@ static inline unsigned int ipv6_clip_hash(struct clip_tbl *d, const u32 *key) } static unsigned int clip_addr_hash(struct clip_tbl *ctbl, const u32 *addr, - int addr_len) + u8 v6) { - return addr_len == 4 ? ipv4_clip_hash(ctbl, addr) : - ipv6_clip_hash(ctbl, addr); + return v6 ? ipv6_clip_hash(ctbl, addr) : + ipv4_clip_hash(ctbl, addr); } static int clip6_get_mbox(const struct net_device *dev, @@ -78,23 +78,22 @@ int cxgb4_clip_get(const struct net_device *dev, const u32 *lip, u8 v6) struct clip_entry *ce, *cte; u32 *addr = (u32 *)lip; int hash; - int addr_len; - int ret = 0; + int ret = -1; if (!ctbl) return 0; - if (v6) - addr_len = 16; - else - addr_len = 4; - - hash = clip_addr_hash(ctbl, addr, addr_len); + hash = clip_addr_hash(ctbl, addr, v6); read_lock_bh(&ctbl->lock); list_for_each_entry(cte, &ctbl->hash_list[hash], list) { - if (addr_len == cte->addr_len && - memcmp(lip, cte->addr, cte->addr_len) == 0) { + if (cte->addr6.sin6_family == AF_INET6 && v6) + ret = memcmp(lip, cte->addr6.sin6_addr.s6_addr, + sizeof(struct in6_addr)); + else if (cte->addr.sin_family == AF_INET && !v6) + ret = memcmp(lip, (char *)(&cte->addr.sin_addr), + sizeof(struct in_addr)); + if (!ret) { ce = cte; read_unlock_bh(&ctbl->lock); goto found; @@ -111,15 +110,20 @@ int cxgb4_clip_get(const struct net_device *dev, const u32 *lip, u8 v6) spin_lock_init(&ce->lock); atomic_set(&ce->refcnt, 0); atomic_dec(&ctbl->nfree); - ce->addr_len = addr_len; - memcpy(ce->addr, lip, addr_len); list_add_tail(&ce->list, &ctbl->hash_list[hash]); if (v6) { + ce->addr6.sin6_family = AF_INET6; + memcpy(ce->addr6.sin6_addr.s6_addr, + lip, sizeof(struct in6_addr)); ret = clip6_get_mbox(dev, (const struct in6_addr *)lip); if (ret) { write_unlock_bh(&ctbl->lock); return ret; } + } else { + ce->addr.sin_family = AF_INET; + memcpy((char *)(&ce->addr.sin_addr), lip, + sizeof(struct in_addr)); } } else { write_unlock_bh(&ctbl->lock); @@ -140,19 +144,19 @@ void cxgb4_clip_release(const struct net_device *dev, const u32 *lip, u8 v6) struct clip_entry *ce, *cte; u32 *addr = (u32 *)lip; int hash; - int addr_len; - - if (v6) - addr_len = 16; - else - addr_len = 4; + int ret = -1; - hash = clip_addr_hash(ctbl, addr, addr_len); + hash = clip_addr_hash(ctbl, addr, v6); read_lock_bh(&ctbl->lock); list_for_each_entry(cte, &ctbl->hash_list[hash], list) { - if (addr_len == cte->addr_len && - memcmp(lip, cte->addr, cte->addr_len) == 0) { + if (cte->addr6.sin6_family == AF_INET6 && v6) + ret = memcmp(lip, cte->addr6.sin6_addr.s6_addr, + sizeof(struct in6_addr)); + else if (cte->addr.sin_family == AF_INET && !v6) + ret = memcmp(lip, (char *)(&cte->addr.sin_addr), + sizeof(struct in_addr)); + if (!ret) { ce = cte; read_unlock_bh(&ctbl->lock); goto found; @@ -249,10 +253,7 @@ int clip_tbl_show(struct seq_file *seq, void *v) for (i = 0 ; i < ctbl->clipt_size; ++i) { list_for_each_entry(ce, &ctbl->hash_list[i], list) { ip[0] = '\0'; - if (ce->addr_len == 16) - sprintf(ip, "%pI6c", ce->addr); - else - sprintf(ip, "%pI4c", ce->addr); + sprintf(ip, "%pISc", &ce->addr); seq_printf(seq, "%-25s %u\n", ip, atomic_read(&ce->refcnt)); } diff --git a/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.h b/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.h index 2eaba0161cf8..35eb43c6bcbb 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.h +++ b/drivers/net/ethernet/chelsio/cxgb4/clip_tbl.h @@ -14,8 +14,10 @@ struct clip_entry { spinlock_t lock; /* Hold while modifying clip reference */ atomic_t refcnt; struct list_head list; - u32 addr[4]; - int addr_len; + union { + struct sockaddr_in addr; + struct sockaddr_in6 addr6; + }; }; struct clip_tbl { -- cgit v1.2.3-59-g8ed1b From 278f7b4fffce9ad267406cf8800df271d14f4a16 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Thu, 19 Feb 2015 12:13:13 +0300 Subject: caif: fix a signedness bug in cfpkt_iterate() The cfpkt_iterate() function can return -EPROTO on error, but the function is a u16 so the negative value gets truncated to a positive unsigned short. This causes a static checker warning. The only caller which might care is cffrml_receive(), when it's checking the frame checksum. I modified cffrml_receive() so that it never says -EPROTO is a valid checksum. Also this isn't ever going to be inlined so I removed the "inline". Signed-off-by: Dan Carpenter Signed-off-by: David S. Miller --- include/net/caif/cfpkt.h | 2 +- net/caif/cffrml.c | 2 +- net/caif/cfpkt_skbuff.c | 6 +++--- 3 files changed, 5 insertions(+), 5 deletions(-) diff --git a/include/net/caif/cfpkt.h b/include/net/caif/cfpkt.h index 1c1ad46250d5..fe328c52c46b 100644 --- a/include/net/caif/cfpkt.h +++ b/include/net/caif/cfpkt.h @@ -171,7 +171,7 @@ struct cfpkt *cfpkt_split(struct cfpkt *pkt, u16 pos); * @return Checksum of buffer. */ -u16 cfpkt_iterate(struct cfpkt *pkt, +int cfpkt_iterate(struct cfpkt *pkt, u16 (*iter_func)(u16 chks, void *buf, u16 len), u16 data); diff --git a/net/caif/cffrml.c b/net/caif/cffrml.c index 8bc7caa28e64..434ba8557826 100644 --- a/net/caif/cffrml.c +++ b/net/caif/cffrml.c @@ -84,7 +84,7 @@ static int cffrml_receive(struct cflayer *layr, struct cfpkt *pkt) u16 tmp; u16 len; u16 hdrchks; - u16 pktchks; + int pktchks; struct cffrml *this; this = container_obj(layr); diff --git a/net/caif/cfpkt_skbuff.c b/net/caif/cfpkt_skbuff.c index 1be0b521ac49..f6c3b2137eea 100644 --- a/net/caif/cfpkt_skbuff.c +++ b/net/caif/cfpkt_skbuff.c @@ -255,9 +255,9 @@ inline u16 cfpkt_getlen(struct cfpkt *pkt) return skb->len; } -inline u16 cfpkt_iterate(struct cfpkt *pkt, - u16 (*iter_func)(u16, void *, u16), - u16 data) +int cfpkt_iterate(struct cfpkt *pkt, + u16 (*iter_func)(u16, void *, u16), + u16 data) { /* * Don't care about the performance hit of linearizing, -- cgit v1.2.3-59-g8ed1b From 342100d937ed6e5faf1e7ee7dcd7b3935fec8877 Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Fri, 20 Feb 2015 00:53:37 +0100 Subject: rhashtable: don't test for shrink on insert, expansion on delete Restore pre 54c5b7d311c8 behaviour and only probe for expansions on inserts and shrinks on deletes. Currently, it will happen that on initial inserts into a sparse hash table, we may i.e. shrink it first simply because it's not fully populated yet, only to later realize that we need to grow again. This however is counter intuitive, e.g. an initial default size of 64 elements is already small enough, and in case an elements size hint is given to the hash table by a user, we should avoid unnecessary expansion steps, so a shrink is clearly unintended here. Fixes: 54c5b7d311c8 ("rhashtable: introduce rhashtable_wakeup_worker helper function") Signed-off-by: Daniel Borkmann Cc: Ying Xue Acked-by: Thomas Graf Signed-off-by: David S. Miller --- lib/rhashtable.c | 27 ++++++++++++++++++--------- 1 file changed, 18 insertions(+), 9 deletions(-) diff --git a/lib/rhashtable.c b/lib/rhashtable.c index 9cc4c4a90d00..38f7879df0d8 100644 --- a/lib/rhashtable.c +++ b/lib/rhashtable.c @@ -537,16 +537,25 @@ unlock: mutex_unlock(&ht->mutex); } -static void rhashtable_wakeup_worker(struct rhashtable *ht) +static void rhashtable_probe_expand(struct rhashtable *ht) { - struct bucket_table *tbl = rht_dereference_rcu(ht->tbl, ht); - struct bucket_table *new_tbl = rht_dereference_rcu(ht->future_tbl, ht); - size_t size = tbl->size; + const struct bucket_table *new_tbl = rht_dereference_rcu(ht->future_tbl, ht); + const struct bucket_table *tbl = rht_dereference_rcu(ht->tbl, ht); /* Only adjust the table if no resizing is currently in progress. */ - if (tbl == new_tbl && - ((ht->p.grow_decision && ht->p.grow_decision(ht, size)) || - (ht->p.shrink_decision && ht->p.shrink_decision(ht, size)))) + if (tbl == new_tbl && ht->p.grow_decision && + ht->p.grow_decision(ht, tbl->size)) + schedule_work(&ht->run_work); +} + +static void rhashtable_probe_shrink(struct rhashtable *ht) +{ + const struct bucket_table *new_tbl = rht_dereference_rcu(ht->future_tbl, ht); + const struct bucket_table *tbl = rht_dereference_rcu(ht->tbl, ht); + + /* Only adjust the table if no resizing is currently in progress. */ + if (tbl == new_tbl && ht->p.shrink_decision && + ht->p.shrink_decision(ht, tbl->size)) schedule_work(&ht->run_work); } @@ -569,7 +578,7 @@ static void __rhashtable_insert(struct rhashtable *ht, struct rhash_head *obj, atomic_inc(&ht->nelems); - rhashtable_wakeup_worker(ht); + rhashtable_probe_expand(ht); } /** @@ -682,7 +691,7 @@ found: if (ret) { atomic_dec(&ht->nelems); - rhashtable_wakeup_worker(ht); + rhashtable_probe_shrink(ht); } rcu_read_unlock(); -- cgit v1.2.3-59-g8ed1b From eb6d1abf1bd8bf1beb45b5401c8324bdb8f893c4 Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Fri, 20 Feb 2015 00:53:38 +0100 Subject: rhashtable: better high order allocation attempts When trying to allocate future tables via bucket_table_alloc(), it seems overkill on large table shifts that we probe for kzalloc() unconditionally first, as it's likely to fail. Only probe with kzalloc() for more reasonable table sizes and use vzalloc() either as a fallback on failure or directly in case of large table sizes. Fixes: 7e1e77636e36 ("lib: Resizable, Scalable, Concurrent Hash Table") Signed-off-by: Daniel Borkmann Acked-by: Thomas Graf Signed-off-by: David S. Miller --- lib/rhashtable.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/lib/rhashtable.c b/lib/rhashtable.c index 38f7879df0d8..b41a5c09832a 100644 --- a/lib/rhashtable.c +++ b/lib/rhashtable.c @@ -217,15 +217,15 @@ static void bucket_table_free(const struct bucket_table *tbl) static struct bucket_table *bucket_table_alloc(struct rhashtable *ht, size_t nbuckets) { - struct bucket_table *tbl; + struct bucket_table *tbl = NULL; size_t size; int i; size = sizeof(*tbl) + nbuckets * sizeof(tbl->buckets[0]); - tbl = kzalloc(size, GFP_KERNEL | __GFP_NOWARN); + if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) + tbl = kzalloc(size, GFP_KERNEL | __GFP_NOWARN | __GFP_NORETRY); if (tbl == NULL) tbl = vzalloc(size); - if (tbl == NULL) return NULL; -- cgit v1.2.3-59-g8ed1b From 6dd0c1655be26345960a6bae574c7dc4648611d3 Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Fri, 20 Feb 2015 00:53:39 +0100 Subject: rhashtable: allow to unload test module There's no good reason why to disallow unloading of the rhashtable test case module. Commit 9d6dbe1bbaf8 moved the code from a boot test into a stand-alone module, but only converted the subsys_initcall() handler into a module_init() function without a related exit handler, and thus preventing the test module from unloading. Fixes: 9d6dbe1bbaf8 ("rhashtable: Make selftest modular") Signed-off-by: Daniel Borkmann Acked-by: Thomas Graf Signed-off-by: David S. Miller --- lib/test_rhashtable.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/lib/test_rhashtable.c b/lib/test_rhashtable.c index f6ce291b68e7..58b995323c44 100644 --- a/lib/test_rhashtable.c +++ b/lib/test_rhashtable.c @@ -223,6 +223,11 @@ static int __init test_rht_init(void) return err; } +static void __exit test_rht_exit(void) +{ +} + module_init(test_rht_init); +module_exit(test_rht_exit); MODULE_LICENSE("GPL v2"); -- cgit v1.2.3-59-g8ed1b From ddede6d536d70c4ef2193ca14208db90740fcd22 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Thu, 19 Feb 2015 11:09:27 -0800 Subject: net: dsa: bcm_sf2: fix 64-bits register reads Reading 64-bits register was not working because we inverted the steps between reading the lower 32-bits of the register and reading the upper 32-bits. Swapping these operations is how the HW guarantees that 64-bits reads are latched correctly. We only have a handful of 64-bits registers for now, mostly MIB counters, so the imapct is low. Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/dsa/bcm_sf2.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/dsa/bcm_sf2.h b/drivers/net/dsa/bcm_sf2.h index ee9f650d5026..7b7053d3c5fa 100644 --- a/drivers/net/dsa/bcm_sf2.h +++ b/drivers/net/dsa/bcm_sf2.h @@ -105,8 +105,8 @@ static inline u64 name##_readq(struct bcm_sf2_priv *priv, u32 off) \ { \ u32 indir, dir; \ spin_lock(&priv->indir_lock); \ - indir = reg_readl(priv, REG_DIR_DATA_READ); \ dir = __raw_readl(priv->name + off); \ + indir = reg_readl(priv, REG_DIR_DATA_READ); \ spin_unlock(&priv->indir_lock); \ return (u64)indir << 32 | dir; \ } \ -- cgit v1.2.3-59-g8ed1b From e7a961c9578ce227d3c62c4cce9463b763a1e0c0 Mon Sep 17 00:00:00 2001 From: Bard Liao Date: Tue, 17 Feb 2015 13:59:27 +0800 Subject: ASoC: rt5670: Fix the speaker mono output issue We need to set left/right control for the speaker amp to get stereo output on speaker. Signed-off-by: Bard Liao Signed-off-by: Mark Brown --- sound/soc/codecs/rt5670.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/sound/soc/codecs/rt5670.c b/sound/soc/codecs/rt5670.c index 8a0833de1665..d33f33ce865a 100644 --- a/sound/soc/codecs/rt5670.c +++ b/sound/soc/codecs/rt5670.c @@ -2591,6 +2591,12 @@ static int rt5670_i2c_probe(struct i2c_client *i2c, regmap_write(rt5670->regmap, RT5670_RESET, 0); + regmap_read(rt5670->regmap, RT5670_VENDOR_ID, &val); + if (val >= 4) + regmap_write(rt5670->regmap, RT5670_GPIO_CTRL3, 0x0980); + else + regmap_write(rt5670->regmap, RT5670_GPIO_CTRL3, 0x0d00); + ret = regmap_register_patch(rt5670->regmap, init_list, ARRAY_SIZE(init_list)); if (ret != 0) -- cgit v1.2.3-59-g8ed1b From 650b7b23cb1e32d77daeefbac1ceb1329abf3b23 Mon Sep 17 00:00:00 2001 From: Petr Mladek Date: Fri, 20 Feb 2015 15:07:29 +0100 Subject: kprobes/x86: Use 5-byte NOP when the code might be modified by ftrace can_probe() checks if the given address points to the beginning of an instruction. It analyzes all the instructions from the beginning of the function until the given address. The code might be modified by another Kprobe. In this case, the current code is read into a buffer, int3 breakpoint is replaced by the saved opcode in the buffer, and can_probe() analyzes the buffer instead. There is a bug that __recover_probed_insn() tries to restore the original code even for Kprobes using the ftrace framework. But in this case, the opcode is not stored. See the difference between arch_prepare_kprobe() and arch_prepare_kprobe_ftrace(). The opcode is stored by arch_copy_kprobe() only from arch_prepare_kprobe(). This patch makes Kprobe to use the ideal 5-byte NOP when the code can be modified by ftrace. It is the original instruction, see ftrace_make_nop() and ftrace_nop_replace(). Note that we always need to use the NOP for ftrace locations. Kprobes do not block ftrace and the instruction might get modified at anytime. It might even be in an inconsistent state because it is modified step by step using the int3 breakpoint. The patch also fixes indentation of the touched comment. Note that I found this problem when playing with Kprobes. I did it on x86_64 with gcc-4.8.3 that supported -mfentry. I modified samples/kprobes/kprobe_example.c and added offset 5 to put the probe right after the fentry area: static struct kprobe kp = { .symbol_name = "do_fork", + .offset = 5, }; Then I was able to load kprobe_example before jprobe_example but not the other way around: $> modprobe jprobe_example $> modprobe kprobe_example modprobe: ERROR: could not insert 'kprobe_example': Invalid or incomplete multibyte or wide character It did not make much sense and debugging pointed to the bug described above. Signed-off-by: Petr Mladek Acked-by: Masami Hiramatsu Cc: Ananth NMavinakayanahalli Cc: Anil S Keshavamurthy Cc: David S. Miller Cc: Frederic Weisbecker Cc: Jiri Kosina Cc: Steven Rostedt Link: http://lkml.kernel.org/r/1424441250-27146-2-git-send-email-pmladek@suse.cz Signed-off-by: Ingo Molnar --- arch/x86/kernel/kprobes/core.c | 42 ++++++++++++++++++++++++++++-------------- 1 file changed, 28 insertions(+), 14 deletions(-) diff --git a/arch/x86/kernel/kprobes/core.c b/arch/x86/kernel/kprobes/core.c index 6a1146ea4d4d..c3b4b46b4797 100644 --- a/arch/x86/kernel/kprobes/core.c +++ b/arch/x86/kernel/kprobes/core.c @@ -223,27 +223,41 @@ static unsigned long __recover_probed_insn(kprobe_opcode_t *buf, unsigned long addr) { struct kprobe *kp; + unsigned long faddr; kp = get_kprobe((void *)addr); - /* There is no probe, return original address */ - if (!kp) + faddr = ftrace_location(addr); + /* + * Use the current code if it is not modified by Kprobe + * and it cannot be modified by ftrace. + */ + if (!kp && !faddr) return addr; /* - * Basically, kp->ainsn.insn has an original instruction. - * However, RIP-relative instruction can not do single-stepping - * at different place, __copy_instruction() tweaks the displacement of - * that instruction. In that case, we can't recover the instruction - * from the kp->ainsn.insn. + * Basically, kp->ainsn.insn has an original instruction. + * However, RIP-relative instruction can not do single-stepping + * at different place, __copy_instruction() tweaks the displacement of + * that instruction. In that case, we can't recover the instruction + * from the kp->ainsn.insn. * - * On the other hand, kp->opcode has a copy of the first byte of - * the probed instruction, which is overwritten by int3. And - * the instruction at kp->addr is not modified by kprobes except - * for the first byte, we can recover the original instruction - * from it and kp->opcode. + * On the other hand, in case on normal Kprobe, kp->opcode has a copy + * of the first byte of the probed instruction, which is overwritten + * by int3. And the instruction at kp->addr is not modified by kprobes + * except for the first byte, we can recover the original instruction + * from it and kp->opcode. + * + * In case of Kprobes using ftrace, we do not have a copy of + * the original instruction. In fact, the ftrace location might + * be modified at anytime and even could be in an inconsistent state. + * Fortunately, we know that the original code is the ideal 5-byte + * long NOP. */ - memcpy(buf, kp->addr, MAX_INSN_SIZE * sizeof(kprobe_opcode_t)); - buf[0] = kp->opcode; + memcpy(buf, (void *)addr, MAX_INSN_SIZE * sizeof(kprobe_opcode_t)); + if (faddr) + memcpy(buf, ideal_nops[NOP_ATOMIC5], 5); + else + buf[0] = kp->opcode; return (unsigned long)buf; } -- cgit v1.2.3-59-g8ed1b From 2a6730c8b6e075adf826a89a3e2caa705807afdb Mon Sep 17 00:00:00 2001 From: Petr Mladek Date: Fri, 20 Feb 2015 15:07:30 +0100 Subject: kprobes/x86: Check for invalid ftrace location in __recover_probed_insn() __recover_probed_insn() should always be called from an address where an instructions starts. The check for ftrace_location() might help to discover a potential inconsistency. This patch adds WARN_ON() when the inconsistency is detected. Also it adds handling of the situation when the original code can not get recovered. Suggested-by: Masami Hiramatsu Signed-off-by: Petr Mladek Cc: Ananth NMavinakayanahalli Cc: Anil S Keshavamurthy Cc: David S. Miller Cc: Frederic Weisbecker Cc: Jiri Kosina Cc: Steven Rostedt Link: http://lkml.kernel.org/r/1424441250-27146-3-git-send-email-pmladek@suse.cz Signed-off-by: Ingo Molnar --- arch/x86/kernel/kprobes/core.c | 12 ++++++++++++ arch/x86/kernel/kprobes/opt.c | 2 ++ 2 files changed, 14 insertions(+) diff --git a/arch/x86/kernel/kprobes/core.c b/arch/x86/kernel/kprobes/core.c index c3b4b46b4797..4e3d5a9621fe 100644 --- a/arch/x86/kernel/kprobes/core.c +++ b/arch/x86/kernel/kprobes/core.c @@ -227,6 +227,13 @@ __recover_probed_insn(kprobe_opcode_t *buf, unsigned long addr) kp = get_kprobe((void *)addr); faddr = ftrace_location(addr); + /* + * Addresses inside the ftrace location are refused by + * arch_check_ftrace_location(). Something went terribly wrong + * if such an address is checked here. + */ + if (WARN_ON(faddr && faddr != addr)) + return 0UL; /* * Use the current code if it is not modified by Kprobe * and it cannot be modified by ftrace. @@ -265,6 +272,7 @@ __recover_probed_insn(kprobe_opcode_t *buf, unsigned long addr) * Recover the probed instruction at addr for further analysis. * Caller must lock kprobes by kprobe_mutex, or disable preemption * for preventing to release referencing kprobes. + * Returns zero if the instruction can not get recovered. */ unsigned long recover_probed_instruction(kprobe_opcode_t *buf, unsigned long addr) { @@ -299,6 +307,8 @@ static int can_probe(unsigned long paddr) * normally used, we just go through if there is no kprobe. */ __addr = recover_probed_instruction(buf, addr); + if (!__addr) + return 0; kernel_insn_init(&insn, (void *)__addr, MAX_INSN_SIZE); insn_get_length(&insn); @@ -347,6 +357,8 @@ int __copy_instruction(u8 *dest, u8 *src) unsigned long recovered_insn = recover_probed_instruction(buf, (unsigned long)src); + if (!recovered_insn) + return 0; kernel_insn_init(&insn, (void *)recovered_insn, MAX_INSN_SIZE); insn_get_length(&insn); /* Another subsystem puts a breakpoint, failed to recover */ diff --git a/arch/x86/kernel/kprobes/opt.c b/arch/x86/kernel/kprobes/opt.c index 7c523bbf3dc8..3aef248ec1ee 100644 --- a/arch/x86/kernel/kprobes/opt.c +++ b/arch/x86/kernel/kprobes/opt.c @@ -259,6 +259,8 @@ static int can_optimize(unsigned long paddr) */ return 0; recovered_insn = recover_probed_instruction(buf, addr); + if (!recovered_insn) + return 0; kernel_insn_init(&insn, (void *)recovered_insn, MAX_INSN_SIZE); insn_get_length(&insn); /* Another subsystem puts a breakpoint */ -- cgit v1.2.3-59-g8ed1b From 014c4d637604c9af2f7f2ff4fd91b725a0c58a5c Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 18 Feb 2015 21:35:08 +0100 Subject: ASoC: Samsung: add missing I2C/SPI dependencies A few sound drivers for the samsung platforms are missing dependencies on I2C or SPI, which can lead to build errors like codecs/rt5631.c:1737:1: warning: data definition has no type or storage class 31_i2c_driver); codecs/rt5631.c:1737:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int] codecs/rt5631.c:1737:1: warning: parameter names (without types) in function declaration codecs/rt5631.c:1726:26: warning: 'rt5631_i2c_driver' defined but not used [-Wunused-variable] I have gone through all the ones that did not already have an I2C dependency and added the ones that I found missing, namely arndale, odroid-x2, littlemill, bells and speyside and this patch adds all the dependencies. Signed-off-by: Arnd Bergmann Signed-off-by: Mark Brown --- sound/soc/samsung/Kconfig | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/sound/soc/samsung/Kconfig b/sound/soc/samsung/Kconfig index fc67f97f19f6..e0c4a4ec4280 100644 --- a/sound/soc/samsung/Kconfig +++ b/sound/soc/samsung/Kconfig @@ -185,7 +185,7 @@ config SND_SOC_SMDK_WM8994_PCM config SND_SOC_SPEYSIDE tristate "Audio support for Wolfson Speyside" - depends on SND_SOC_SAMSUNG && MACH_WLF_CRAGG_6410 + depends on SND_SOC_SAMSUNG && MACH_WLF_CRAGG_6410 && I2C && SPI_MASTER select SND_SAMSUNG_I2S select SND_SOC_WM8996 select SND_SOC_WM9081 @@ -200,7 +200,7 @@ config SND_SOC_TOBERMORY config SND_SOC_BELLS tristate "Audio support for Wolfson Bells" - depends on SND_SOC_SAMSUNG && MACH_WLF_CRAGG_6410 && MFD_ARIZONA + depends on SND_SOC_SAMSUNG && MACH_WLF_CRAGG_6410 && MFD_ARIZONA && I2C && SPI_MASTER select SND_SAMSUNG_I2S select SND_SOC_WM5102 select SND_SOC_WM5110 @@ -217,7 +217,7 @@ config SND_SOC_LOWLAND config SND_SOC_LITTLEMILL tristate "Audio support for Wolfson Littlemill" - depends on SND_SOC_SAMSUNG && MACH_WLF_CRAGG_6410 + depends on SND_SOC_SAMSUNG && MACH_WLF_CRAGG_6410 && I2C select SND_SAMSUNG_I2S select MFD_WM8994 select SND_SOC_WM8994 @@ -234,7 +234,7 @@ config SND_SOC_SNOW config SND_SOC_ODROIDX2 tristate "Audio support for Odroid-X2 and Odroid-U3" - depends on SND_SOC_SAMSUNG + depends on SND_SOC_SAMSUNG && I2C select SND_SOC_MAX98090 select SND_SAMSUNG_I2S help @@ -242,6 +242,6 @@ config SND_SOC_ODROIDX2 config SND_SOC_ARNDALE_RT5631_ALC5631 tristate "Audio support for RT5631(ALC5631) on Arndale Board" - depends on SND_SOC_SAMSUNG + depends on SND_SOC_SAMSUNG && I2C select SND_SAMSUNG_I2S select SND_SOC_RT5631 -- cgit v1.2.3-59-g8ed1b From 52554fbd2f88a432a16e9e88e14c4b02ccb7cdb6 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 18 Feb 2015 21:43:13 +0100 Subject: ASoC: cirrus: tlv320aic23 needs I2C The tlv320aic23 codec is selected by the ep93xx snapper platform, which are missing a dependency on I2C, and that can result in this build error, as found during randconfig builds: .../codecs/tlv320aic23-i2c.c: In function 'tlv320aic23_i2c_probe': .../codecs/tlv320aic23-i2c.c:27:2: error: implicit declaration of function 'i2c_check_functionality' [-Werror=implicit-function-declaration] if (!i2c_check_functionality(i2c->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) ^ This adds the missing dependency. Signed-off-by: Arnd Bergmann Signed-off-by: Mark Brown --- sound/soc/cirrus/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/cirrus/Kconfig b/sound/soc/cirrus/Kconfig index 7b7fbcd49e5e..c7cd60f009e9 100644 --- a/sound/soc/cirrus/Kconfig +++ b/sound/soc/cirrus/Kconfig @@ -16,7 +16,7 @@ config SND_EP93XX_SOC_AC97 config SND_EP93XX_SOC_SNAPPERCL15 tristate "SoC Audio support for Bluewater Systems Snapper CL15 module" - depends on SND_EP93XX_SOC && MACH_SNAPPER_CL15 + depends on SND_EP93XX_SOC && MACH_SNAPPER_CL15 && I2C select SND_EP93XX_SOC_I2S select SND_SOC_TLV320AIC23_I2C help -- cgit v1.2.3-59-g8ed1b From 08d0a55c33393e6dc838e37b7a8657c28a6de10d Mon Sep 17 00:00:00 2001 From: Kenneth Westfield Date: Tue, 17 Feb 2015 00:53:11 -0800 Subject: ASoC: max98357a: Add missing header files Add missing header files to avoid implicit declarations and indirect inclusions. Signed-off-by: Kenneth Westfield Signed-off-by: Mark Brown --- sound/soc/codecs/max98357a.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/sound/soc/codecs/max98357a.c b/sound/soc/codecs/max98357a.c index f493fb6fd4ea..e9e6efbc21dd 100644 --- a/sound/soc/codecs/max98357a.c +++ b/sound/soc/codecs/max98357a.c @@ -12,10 +12,19 @@ * max98357a.c -- MAX98357A ALSA SoC Codec driver */ -#include +#include +#include #include #include +#include +#include +#include +#include +#include +#include #include +#include +#include #define DRV_NAME "max98357a" -- cgit v1.2.3-59-g8ed1b From a4176a9391868bfa87705bcd2e3b49e9b9dd2996 Mon Sep 17 00:00:00 2001 From: Matthew Thode Date: Tue, 17 Feb 2015 18:31:57 -0600 Subject: net: reject creation of netdev names with colons colons are used as a separator in netdev device lookup in dev_ioctl.c Specific functions are SIOCGIFTXQLEN SIOCETHTOOL SIOCSIFNAME Signed-off-by: Matthew Thode Signed-off-by: David S. Miller --- net/core/dev.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/core/dev.c b/net/core/dev.c index 8f9710c62e20..962ee9d71964 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -946,7 +946,7 @@ bool dev_valid_name(const char *name) return false; while (*name) { - if (*name == '/' || isspace(*name)) + if (*name == '/' || *name == ':' || isspace(*name)) return false; name++; } -- cgit v1.2.3-59-g8ed1b From b9ebafbe8cfeeddec881504c446cccd0d87a51b6 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 20 Feb 2015 06:48:57 -0800 Subject: rhashtable: ensure cache line alignment on bucket_table struct bucket_table contains mostly read fields : size, locks_mask, locks. Make sure these are not sharing a cache line with buckets[] Signed-off-by: Eric Dumazet Acked-by: Daniel Borkmann Acked-by: Thomas Graf Signed-off-by: David S. Miller --- include/linux/rhashtable.h | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/include/linux/rhashtable.h b/include/linux/rhashtable.h index 58851275fed9..cb2104be2135 100644 --- a/include/linux/rhashtable.h +++ b/include/linux/rhashtable.h @@ -54,10 +54,11 @@ struct rhash_head { * @buckets: size * hash buckets */ struct bucket_table { - size_t size; - unsigned int locks_mask; - spinlock_t *locks; - struct rhash_head __rcu *buckets[]; + size_t size; + unsigned int locks_mask; + spinlock_t *locks; + + struct rhash_head __rcu *buckets[] ____cacheline_aligned_in_smp; }; typedef u32 (*rht_hashfn_t)(const void *data, u32 len, u32 seed); -- cgit v1.2.3-59-g8ed1b From 3f34b24a732bab9635c4b32823268c37c01b40f0 Mon Sep 17 00:00:00 2001 From: Alexander Drozdov Date: Fri, 20 Feb 2015 08:24:27 +0300 Subject: af_packet: allow packets defragmentation not only for hash fanout type Packets defragmentation was introduced for PACKET_FANOUT_HASH only, see 7736d33f4262 ("packet: Add pre-defragmentation support for ipv4 fanouts") It may be useful to have defragmentation enabled regardless of fanout type. Without that, the AF_PACKET user may have to: 1. Collect fragments from different rings 2. Defragment by itself Signed-off-by: Alexander Drozdov Signed-off-by: David S. Miller --- net/packet/af_packet.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/net/packet/af_packet.c b/net/packet/af_packet.c index 9c28cec1a083..99fc628f7372 100644 --- a/net/packet/af_packet.c +++ b/net/packet/af_packet.c @@ -1349,14 +1349,14 @@ static int packet_rcv_fanout(struct sk_buff *skb, struct net_device *dev, return 0; } + if (fanout_has_flag(f, PACKET_FANOUT_FLAG_DEFRAG)) { + skb = ip_check_defrag(skb, IP_DEFRAG_AF_PACKET); + if (!skb) + return 0; + } switch (f->type) { case PACKET_FANOUT_HASH: default: - if (fanout_has_flag(f, PACKET_FANOUT_FLAG_DEFRAG)) { - skb = ip_check_defrag(skb, IP_DEFRAG_AF_PACKET); - if (!skb) - return 0; - } idx = fanout_demux_hash(f, skb, num); break; case PACKET_FANOUT_LB: -- cgit v1.2.3-59-g8ed1b From a927792c196f1c24410f3c12ccf45238a353783a Mon Sep 17 00:00:00 2001 From: Yannick Guerrini Date: Sat, 21 Feb 2015 23:41:50 +0100 Subject: x86/cpu/intel: Fix trivial typo in intel_tlb_table[] Change 'ssociative' to 'associative' Signed-off-by: Yannick Guerrini Cc: Borislav Petkov Cc: Bryan O'Donoghue Cc: Chris Bainbridge Cc: Dave Hansen Cc: Steven Honeyman Cc: trivial@kernel.org Link: http://lkml.kernel.org/r/1424558510-1420-1-git-send-email-yguerrini@tomshardware.fr Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/intel.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/cpu/intel.c b/arch/x86/kernel/cpu/intel.c index 94d7dcb12145..50163fa9034f 100644 --- a/arch/x86/kernel/cpu/intel.c +++ b/arch/x86/kernel/cpu/intel.c @@ -565,8 +565,8 @@ static const struct _tlb_table intel_tlb_table[] = { { 0xb2, TLB_INST_4K, 64, " TLB_INST 4KByte pages, 4-way set associative" }, { 0xb3, TLB_DATA_4K, 128, " TLB_DATA 4 KByte pages, 4-way set associative" }, { 0xb4, TLB_DATA_4K, 256, " TLB_DATA 4 KByte pages, 4-way associative" }, - { 0xb5, TLB_INST_4K, 64, " TLB_INST 4 KByte pages, 8-way set ssociative" }, - { 0xb6, TLB_INST_4K, 128, " TLB_INST 4 KByte pages, 8-way set ssociative" }, + { 0xb5, TLB_INST_4K, 64, " TLB_INST 4 KByte pages, 8-way set associative" }, + { 0xb6, TLB_INST_4K, 128, " TLB_INST 4 KByte pages, 8-way set associative" }, { 0xba, TLB_DATA_4K, 64, " TLB_DATA 4 KByte pages, 4-way associative" }, { 0xc0, TLB_DATA_4K_4M, 8, " TLB_DATA 4 KByte and 4 MByte pages, 4-way associative" }, { 0xc1, STLB_4K_2M, 1024, " STLB 4 KByte and 2 MByte pages, 8-way associative" }, -- cgit v1.2.3-59-g8ed1b From b841118ee6c0917004e7e763c4f6bf8eb10a6d93 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Wed, 18 Feb 2015 12:39:46 +0100 Subject: iio: common: ssp_sensors: Protect PM-only functions to kill warning MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit If CONFIG_PM_SLEEP=n: drivers/iio/common/ssp_sensors/ssp_dev.c:644: warning: ‘ssp_suspend’ defined but not used drivers/iio/common/ssp_sensors/ssp_dev.c:669: warning: ‘ssp_resume’ defined but not used Protect the unused functions by #ifdef CONFIG_PM_SLEEP to fix this. Signed-off-by: Geert Uytterhoeven Acked-by: Karol Wrona Signed-off-by: Jonathan Cameron --- drivers/iio/common/ssp_sensors/ssp_dev.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/iio/common/ssp_sensors/ssp_dev.c b/drivers/iio/common/ssp_sensors/ssp_dev.c index 52d70435f5a1..55a90082a29b 100644 --- a/drivers/iio/common/ssp_sensors/ssp_dev.c +++ b/drivers/iio/common/ssp_sensors/ssp_dev.c @@ -640,6 +640,7 @@ static int ssp_remove(struct spi_device *spi) return 0; } +#ifdef CONFIG_PM_SLEEP static int ssp_suspend(struct device *dev) { int ret; @@ -688,6 +689,7 @@ static int ssp_resume(struct device *dev) return 0; } +#endif /* CONFIG_PM_SLEEP */ static const struct dev_pm_ops ssp_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(ssp_suspend, ssp_resume) -- cgit v1.2.3-59-g8ed1b From 45cee4f594bcb3083c2d8475462af2f2ddf29aff Mon Sep 17 00:00:00 2001 From: Fabian Frederick Date: Fri, 20 Feb 2015 19:12:52 +0100 Subject: mISDN: replace current->state by set_current_state() Use helper function to access current->state. Direct assignments are prone to races and therefore buggy. Thanks to Peter Zijlstra for the exact definition of the problem. Signed-off-by: Fabian Frederick Signed-off-by: David S. Miller --- drivers/isdn/hardware/mISDN/hfcpci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/isdn/hardware/mISDN/hfcpci.c b/drivers/isdn/hardware/mISDN/hfcpci.c index 3c92780bda09..ff48da61c94c 100644 --- a/drivers/isdn/hardware/mISDN/hfcpci.c +++ b/drivers/isdn/hardware/mISDN/hfcpci.c @@ -1755,7 +1755,7 @@ init_card(struct hfc_pci *hc) enable_hwirq(hc); spin_unlock_irqrestore(&hc->lock, flags); /* Timeout 80ms */ - current->state = TASK_UNINTERRUPTIBLE; + set_current_state(TASK_UNINTERRUPTIBLE); schedule_timeout((80 * HZ) / 1000); printk(KERN_INFO "HFC PCI: IRQ %d count %d\n", hc->irq, hc->irqcnt); -- cgit v1.2.3-59-g8ed1b From 50462ce0052c67b5a06f19fb7c7f308813006879 Mon Sep 17 00:00:00 2001 From: Fabian Frederick Date: Fri, 20 Feb 2015 19:12:55 +0100 Subject: hso: replace current->state by __set_current_state() Use helper functions to access current->state. Direct assignments are prone to races and therefore buggy. Thanks to Peter Zijlstra for the exact definition of the problem. Suggested-By: Peter Zijlstra Signed-off-by: Fabian Frederick Signed-off-by: David S. Miller --- drivers/net/usb/hso.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c index 9cdfb3fe9c15..778e91531fac 100644 --- a/drivers/net/usb/hso.c +++ b/drivers/net/usb/hso.c @@ -1594,7 +1594,7 @@ hso_wait_modem_status(struct hso_serial *serial, unsigned long arg) } cprev = cnow; } - current->state = TASK_RUNNING; + __set_current_state(TASK_RUNNING); remove_wait_queue(&tiocmget->waitq, &wait); return ret; -- cgit v1.2.3-59-g8ed1b From 2c45015a66a171de306e23991fec998667b49acf Mon Sep 17 00:00:00 2001 From: Fabian Frederick Date: Fri, 20 Feb 2015 19:12:56 +0100 Subject: wan: cosa: replace current->state by set_current_state() Use helper functions to access current->state. Direct assignments are prone to races and therefore buggy. current->state = TASK_RUNNING is replaced by __set_current_state() Thanks to Peter Zijlstra for the exact definition of the problem. Suggested-By: Peter Zijlstra Signed-off-by: Fabian Frederick Acked-By: Jan "Yenya" Kasprzak Signed-off-by: David S. Miller --- drivers/net/wan/cosa.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/wan/cosa.c b/drivers/net/wan/cosa.c index 83c39e2858bf..88d121d43c08 100644 --- a/drivers/net/wan/cosa.c +++ b/drivers/net/wan/cosa.c @@ -806,21 +806,21 @@ static ssize_t cosa_read(struct file *file, spin_lock_irqsave(&cosa->lock, flags); add_wait_queue(&chan->rxwaitq, &wait); while (!chan->rx_status) { - current->state = TASK_INTERRUPTIBLE; + set_current_state(TASK_INTERRUPTIBLE); spin_unlock_irqrestore(&cosa->lock, flags); schedule(); spin_lock_irqsave(&cosa->lock, flags); if (signal_pending(current) && chan->rx_status == 0) { chan->rx_status = 1; remove_wait_queue(&chan->rxwaitq, &wait); - current->state = TASK_RUNNING; + __set_current_state(TASK_RUNNING); spin_unlock_irqrestore(&cosa->lock, flags); mutex_unlock(&chan->rlock); return -ERESTARTSYS; } } remove_wait_queue(&chan->rxwaitq, &wait); - current->state = TASK_RUNNING; + __set_current_state(TASK_RUNNING); kbuf = chan->rxdata; count = chan->rxsize; spin_unlock_irqrestore(&cosa->lock, flags); @@ -890,14 +890,14 @@ static ssize_t cosa_write(struct file *file, spin_lock_irqsave(&cosa->lock, flags); add_wait_queue(&chan->txwaitq, &wait); while (!chan->tx_status) { - current->state = TASK_INTERRUPTIBLE; + set_current_state(TASK_INTERRUPTIBLE); spin_unlock_irqrestore(&cosa->lock, flags); schedule(); spin_lock_irqsave(&cosa->lock, flags); if (signal_pending(current) && chan->tx_status == 0) { chan->tx_status = 1; remove_wait_queue(&chan->txwaitq, &wait); - current->state = TASK_RUNNING; + __set_current_state(TASK_RUNNING); chan->tx_status = 1; spin_unlock_irqrestore(&cosa->lock, flags); up(&chan->wsem); @@ -905,7 +905,7 @@ static ssize_t cosa_write(struct file *file, } } remove_wait_queue(&chan->txwaitq, &wait); - current->state = TASK_RUNNING; + __set_current_state(TASK_RUNNING); up(&chan->wsem); spin_unlock_irqrestore(&cosa->lock, flags); kfree(kbuf); -- cgit v1.2.3-59-g8ed1b From 87cda7cb4380fa05b70485b0a57b07d020f5204b Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 22 Feb 2015 15:54:29 -0500 Subject: r8169: Revert BQL and xmit_more support. There are certain regressions which are pointing to these two commits which we are having a hard time resolving. So revert them for now. Specifically this reverts: commit 0bec3b700d106a8b0a34227b2976d1a582f1aab7 Author: Florian Westphal Date: Wed Jan 7 10:49:49 2015 +0100 r8169: add support for xmit_more and commit 1e918876853aa85435e0f17fd8b4a92dcfff53d6 Author: Florian Westphal Date: Wed Oct 1 13:38:03 2014 +0200 r8169: add support for Byte Queue Limits There were some attempts by Eric Dumazet to address some obvious problems in the TX flow, to see if they would fix the problems, but none of them seem to help for the regression reporters. Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 30 +++++++----------------------- 1 file changed, 7 insertions(+), 23 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index ad0020af2193..b1560927abd4 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -5067,8 +5067,6 @@ static void rtl_hw_reset(struct rtl8169_private *tp) RTL_W8(ChipCmd, CmdReset); rtl_udelay_loop_wait_low(tp, &rtl_chipcmd_cond, 100, 100); - - netdev_reset_queue(tp->dev); } static void rtl_request_uncached_firmware(struct rtl8169_private *tp) @@ -7049,7 +7047,6 @@ static netdev_tx_t rtl8169_start_xmit(struct sk_buff *skb, u32 status, len; u32 opts[2]; int frags; - bool stop_queue; if (unlikely(!TX_FRAGS_READY_FOR(tp, skb_shinfo(skb)->nr_frags))) { netif_err(tp, drv, dev, "BUG! Tx Ring full when queue awake!\n"); @@ -7090,8 +7087,6 @@ static netdev_tx_t rtl8169_start_xmit(struct sk_buff *skb, txd->opts2 = cpu_to_le32(opts[1]); - netdev_sent_queue(dev, skb->len); - skb_tx_timestamp(skb); /* Force memory writes to complete before releasing descriptor */ @@ -7106,16 +7101,11 @@ static netdev_tx_t rtl8169_start_xmit(struct sk_buff *skb, tp->cur_tx += frags + 1; - stop_queue = !TX_FRAGS_READY_FOR(tp, MAX_SKB_FRAGS); + RTL_W8(TxPoll, NPQ); - if (!skb->xmit_more || stop_queue || - netif_xmit_stopped(netdev_get_tx_queue(dev, 0))) { - RTL_W8(TxPoll, NPQ); - - mmiowb(); - } + mmiowb(); - if (stop_queue) { + if (!TX_FRAGS_READY_FOR(tp, MAX_SKB_FRAGS)) { /* Avoid wrongly optimistic queue wake-up: rtl_tx thread must * not miss a ring update when it notices a stopped queue. */ @@ -7198,7 +7188,6 @@ static void rtl8169_pcierr_interrupt(struct net_device *dev) static void rtl_tx(struct net_device *dev, struct rtl8169_private *tp) { unsigned int dirty_tx, tx_left; - unsigned int bytes_compl = 0, pkts_compl = 0; dirty_tx = tp->dirty_tx; smp_rmb(); @@ -7222,8 +7211,10 @@ static void rtl_tx(struct net_device *dev, struct rtl8169_private *tp) rtl8169_unmap_tx_skb(&tp->pci_dev->dev, tx_skb, tp->TxDescArray + entry); if (status & LastFrag) { - pkts_compl++; - bytes_compl += tx_skb->skb->len; + u64_stats_update_begin(&tp->tx_stats.syncp); + tp->tx_stats.packets++; + tp->tx_stats.bytes += tx_skb->skb->len; + u64_stats_update_end(&tp->tx_stats.syncp); dev_kfree_skb_any(tx_skb->skb); tx_skb->skb = NULL; } @@ -7232,13 +7223,6 @@ static void rtl_tx(struct net_device *dev, struct rtl8169_private *tp) } if (tp->dirty_tx != dirty_tx) { - netdev_completed_queue(tp->dev, pkts_compl, bytes_compl); - - u64_stats_update_begin(&tp->tx_stats.syncp); - tp->tx_stats.packets += pkts_compl; - tp->tx_stats.bytes += bytes_compl; - u64_stats_update_end(&tp->tx_stats.syncp); - tp->dirty_tx = dirty_tx; /* Sync with rtl8169_start_xmit: * - publish dirty_tx ring index (write barrier) -- cgit v1.2.3-59-g8ed1b From c4ce0da8ec62d83c96e29db7dadd6d3985344bb3 Mon Sep 17 00:00:00 2001 From: Petr Mladek Date: Wed, 18 Feb 2015 18:02:13 +0100 Subject: livepatch: RCU protect struct klp_func all the time when used in klp_ftrace_handler() func->new_func has been accessed after rcu_read_unlock() in klp_ftrace_handler() and therefore the access was not protected. Signed-off-by: Petr Mladek Acked-by: Josh Poimboeuf Signed-off-by: Jiri Kosina --- kernel/livepatch/core.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/kernel/livepatch/core.c b/kernel/livepatch/core.c index 69bf3aa3bde8..782172f073c5 100644 --- a/kernel/livepatch/core.c +++ b/kernel/livepatch/core.c @@ -314,12 +314,12 @@ static void notrace klp_ftrace_handler(unsigned long ip, rcu_read_lock(); func = list_first_or_null_rcu(&ops->func_stack, struct klp_func, stack_node); - rcu_read_unlock(); - if (WARN_ON_ONCE(!func)) - return; + goto unlock; klp_arch_set_pc(regs, (unsigned long)func->new_func); +unlock: + rcu_read_unlock(); } static int klp_disable_func(struct klp_func *func) -- cgit v1.2.3-59-g8ed1b From e17fdaeaec066c725f73cd3cda1feae52b2646f5 Mon Sep 17 00:00:00 2001 From: Bruce Merry Date: Thu, 15 Jan 2015 11:20:22 +0200 Subject: perf bench: Fix order of arguments to memcpy_alloc_mem This was causing the destination instead of the source to be filled. As a result, the source was typically all mapped to one zero page, and hence very cacheable. Signed-off-by: Bruce Merry Acked-by: Ingo Molnar Cc: Paul Mackerras Cc: Peter Zijlstra Link: http://lkml.kernel.org/r/20150115092022.GA11292@kryton Signed-off-by: Arnaldo Carvalho de Melo --- tools/perf/bench/mem-memcpy.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/tools/perf/bench/mem-memcpy.c b/tools/perf/bench/mem-memcpy.c index 6c14afe8c1b1..db1d3a29d97f 100644 --- a/tools/perf/bench/mem-memcpy.c +++ b/tools/perf/bench/mem-memcpy.c @@ -289,7 +289,7 @@ static u64 do_memcpy_cycle(const struct routine *r, size_t len, bool prefault) memcpy_t fn = r->fn.memcpy; int i; - memcpy_alloc_mem(&src, &dst, len); + memcpy_alloc_mem(&dst, &src, len); if (prefault) fn(dst, src, len); @@ -312,7 +312,7 @@ static double do_memcpy_gettimeofday(const struct routine *r, size_t len, void *src = NULL, *dst = NULL; int i; - memcpy_alloc_mem(&src, &dst, len); + memcpy_alloc_mem(&dst, &src, len); if (prefault) fn(dst, src, len); -- cgit v1.2.3-59-g8ed1b From 52d6c8c6ca125872459054daa70f2f1c698c8e75 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Sun, 22 Feb 2015 17:03:41 -0800 Subject: net: pktgen: disable xmit_clone on virtual devices Trying to use burst capability (aka xmit_more) on a virtual device like bonding is not supported. For example, skb might be queued multiple times on a qdisc, with various list corruptions. Fixes: 38b2cf2982dc ("net: pktgen: packet bursting via skb->xmit_more") Signed-off-by: Eric Dumazet Cc: Alexei Starovoitov Acked-by: Alexei Starovoitov Signed-off-by: David S. Miller --- net/core/pktgen.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/net/core/pktgen.c b/net/core/pktgen.c index b4899f5b7388..508155b283dd 100644 --- a/net/core/pktgen.c +++ b/net/core/pktgen.c @@ -1134,6 +1134,9 @@ static ssize_t pktgen_if_write(struct file *file, return len; i += len; + if ((value > 1) && + (!(pkt_dev->odev->priv_flags & IFF_TX_SKB_SHARING))) + return -ENOTSUPP; pkt_dev->burst = value < 1 ? 1 : value; sprintf(pg_result, "OK: burst=%d", pkt_dev->burst); return count; -- cgit v1.2.3-59-g8ed1b From fea559f303567e558bfab9c8ba4a2af5b309205a Mon Sep 17 00:00:00 2001 From: Paul Clarke Date: Fri, 20 Feb 2015 11:13:33 -0600 Subject: powerpc: Re-enable dynticks Implement arch_irq_work_has_interrupt() for powerpc Commit 9b01f5bf3 introduced a dependency on "IRQ work self-IPIs" for full dynamic ticks to be enabled, by expecting architectures to implement a suitable arch_irq_work_has_interrupt() routine. Several arches have implemented this routine, including x86 (3010279f) and arm (09f6edd4), but powerpc was omitted. This patch implements this routine for powerpc. The symptom, at boot (on powerpc systems) with "nohz_full=" is displayed: NO_HZ: Can't run full dynticks because arch doesn't support irq work self-IPIs after this patch: NO_HZ: Full dynticks CPUs: . Tested against 3.19. powerpc implements "IRQ work self-IPIs" by setting the decrementer to 1 in arch_irq_work_raise(), which causes a decrementer exception on the next timebase tick. We then handle the work in __timer_interrupt(). CC: Frederic Weisbecker Signed-off-by: Paul A. Clarke Reviewed-by: Paul E. McKenney [mpe: Flesh out change log, fix ws & include guards, remove include of processor.h] Signed-off-by: Michael Ellerman --- arch/powerpc/include/asm/irq_work.h | 9 +++++++++ 1 file changed, 9 insertions(+) create mode 100644 arch/powerpc/include/asm/irq_work.h diff --git a/arch/powerpc/include/asm/irq_work.h b/arch/powerpc/include/asm/irq_work.h new file mode 100644 index 000000000000..744fd54de374 --- /dev/null +++ b/arch/powerpc/include/asm/irq_work.h @@ -0,0 +1,9 @@ +#ifndef _ASM_POWERPC_IRQ_WORK_H +#define _ASM_POWERPC_IRQ_WORK_H + +static inline bool arch_irq_work_has_interrupt(void) +{ + return true; +} + +#endif /* _ASM_POWERPC_IRQ_WORK_H */ -- cgit v1.2.3-59-g8ed1b From 6514890f7aa8dd75fa46e282a1c7a8615e86f363 Mon Sep 17 00:00:00 2001 From: Neal Cardwell Date: Fri, 20 Feb 2015 13:33:16 -0500 Subject: tcp: fix tcp_should_expand_sndbuf() to use tcp_packets_in_flight() tcp_should_expand_sndbuf() does not expand the send buffer if we have filled the congestion window. However, it should use tcp_packets_in_flight() instead of tp->packets_out to make this check. Testing has established that the difference matters a lot if there are many SACKed packets, causing a needless performance shortfall. Signed-off-by: Neal Cardwell Signed-off-by: Yuchung Cheng Signed-off-by: Eric Dumazet Signed-off-by: Nandita Dukkipati Signed-off-by: David S. Miller --- net/ipv4/tcp_input.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/ipv4/tcp_input.c b/net/ipv4/tcp_input.c index 8fdd27b17306..fb4cf8b8e121 100644 --- a/net/ipv4/tcp_input.c +++ b/net/ipv4/tcp_input.c @@ -4770,7 +4770,7 @@ static bool tcp_should_expand_sndbuf(const struct sock *sk) return false; /* If we filled the congestion window, do not expand. */ - if (tp->packets_out >= tp->snd_cwnd) + if (tcp_packets_in_flight(tp) >= tp->snd_cwnd) return false; return true; -- cgit v1.2.3-59-g8ed1b From d9ef72cd1c15c2fc1f7131cd78304dd21bc15953 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Tue, 10 Feb 2015 18:24:07 +0800 Subject: hwmon: (ads7828) Check return value of devm_regmap_init_i2c devm_regmap_init_i2c() can fail, thus add return value checking. Signed-off-by: Axel Lin Signed-off-by: Guenter Roeck --- drivers/hwmon/ads7828.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/hwmon/ads7828.c b/drivers/hwmon/ads7828.c index bce4e9ff21bf..6c99ee7bafa3 100644 --- a/drivers/hwmon/ads7828.c +++ b/drivers/hwmon/ads7828.c @@ -147,6 +147,9 @@ static int ads7828_probe(struct i2c_client *client, &ads2830_regmap_config); } + if (IS_ERR(data->regmap)) + return PTR_ERR(data->regmap); + data->cmd_byte = ext_vref ? ADS7828_CMD_PD1 : ADS7828_CMD_PD3; if (!diff_input) data->cmd_byte |= ADS7828_CMD_SD_SE; -- cgit v1.2.3-59-g8ed1b From 2035772010db634ec8566b658fb1cd87ec47ac77 Mon Sep 17 00:00:00 2001 From: George Cherian Date: Wed, 5 Mar 2014 14:01:43 +0530 Subject: usb: musb: musb_host: Enable HCD_BH flag to handle urb return in bottom half Enable HCD_BH flag for musb host controller driver. This improves the MSC/UVC through put. With this enabled even 640x480@30fps webcam streaming is also supported. Signed-off-by: George Cherian Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_host.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c index 883a9adfdfff..c3d5fc9dfb5b 100644 --- a/drivers/usb/musb/musb_host.c +++ b/drivers/usb/musb/musb_host.c @@ -2613,7 +2613,7 @@ static const struct hc_driver musb_hc_driver = { .description = "musb-hcd", .product_desc = "MUSB HDRC host driver", .hcd_priv_size = sizeof(struct musb *), - .flags = HCD_USB2 | HCD_MEMORY, + .flags = HCD_USB2 | HCD_MEMORY | HCD_BH, /* not using irq handler or reset hooks from usbcore, since * those must be shared with peripheral code for OTG configs -- cgit v1.2.3-59-g8ed1b From 9ec36f7fe20ef919cc15171e1da1b6739222541a Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Mon, 2 Feb 2015 16:24:17 -0600 Subject: usb: gadget: function: phonet: balance usb_ep_disable calls MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit f_phonet's ->set_alt() method will call usb_ep_disable() potentially on an endpoint which is already disabled. That's something the gadget/function driver must guarantee that it's always balanced. In order to balance the calls, just make sure the endpoint was enabled before by means of checking the validity of driver_data. Reported-by: Pali Rohár Signed-off-by: Felipe Balbi --- drivers/usb/gadget/function/f_phonet.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/usb/gadget/function/f_phonet.c b/drivers/usb/gadget/function/f_phonet.c index c89e96cfa3e4..c0c3ef272714 100644 --- a/drivers/usb/gadget/function/f_phonet.c +++ b/drivers/usb/gadget/function/f_phonet.c @@ -417,7 +417,10 @@ static int pn_set_alt(struct usb_function *f, unsigned intf, unsigned alt) return -EINVAL; spin_lock(&port->lock); - __pn_reset(f); + + if (fp->in_ep->driver_data) + __pn_reset(f); + if (alt == 1) { int i; -- cgit v1.2.3-59-g8ed1b From 3e43a0725637299a14369e3ef109c25a8ec5c008 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Mon, 2 Feb 2015 17:12:00 -0600 Subject: usb: musb: core: add pm_runtime_irq_safe() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit We need a pm_runtime_get_sync() call from within musb_gadget_pullup() to make sure registers are accessible at that time. The problem is that musb_gadget_pullup() is called with IRQs disabled and, because of that, we need to tell pm_runtime that this pm_runtime_get_sync() is IRQ safe. We can simply add pm_runtime_irq_safe(), however, because we need to make our read/write accessor function pointers have been initialized before trying to use them. This means that all pm_runtime initialization for musb_core needs to be moved down so that when we call pm_runtime_irq_safe(), the pm_runtime_get_sync() that it calls on the parent, won't cause a crash due to NULL musb_read/write accessors. Reported-by: Pali Rohár Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_core.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index e6f4cbfeed97..067920f2d570 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -1969,10 +1969,6 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) goto fail0; } - pm_runtime_use_autosuspend(musb->controller); - pm_runtime_set_autosuspend_delay(musb->controller, 200); - pm_runtime_enable(musb->controller); - spin_lock_init(&musb->lock); musb->board_set_power = plat->set_power; musb->min_power = plat->min_power; @@ -1991,6 +1987,12 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) musb_readl = musb_default_readl; musb_writel = musb_default_writel; + /* We need musb_read/write functions initialized for PM */ + pm_runtime_use_autosuspend(musb->controller); + pm_runtime_set_autosuspend_delay(musb->controller, 200); + pm_runtime_irq_safe(musb->controller); + pm_runtime_enable(musb->controller); + /* The musb_platform_init() call: * - adjusts musb->mregs * - sets the musb->isr -- cgit v1.2.3-59-g8ed1b From 407550fe2ccfca3fa0ac4bcdb0a412adeabf84ba Mon Sep 17 00:00:00 2001 From: Marcel Holtmann Date: Sun, 22 Feb 2015 15:41:18 -0800 Subject: Bluetooth: btusb: Fix issue with CSR based Intel Wireless controllers Older Wireless controllers from Intel used CSR chips to provide support for Bluetooth. The commit d0ac9eb72 (Bluetooth: btusb: Ignore unknown Intel devices with generic descriptor) disabled these older controllers. To enable them again, put them into the blacklist and mark them clearly as CSR based controllers. T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=07da Rev=78.69 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Reported-by: Kenneth R. Crudup Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg --- drivers/bluetooth/btusb.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index b87688881143..8bfc4c2bba87 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -272,6 +272,7 @@ static const struct usb_device_id blacklist_table[] = { { USB_DEVICE(0x1286, 0x2046), .driver_info = BTUSB_MARVELL }, /* Intel Bluetooth devices */ + { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR }, { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL }, { USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL }, { USB_DEVICE(0x8087, 0x0a2b), .driver_info = BTUSB_INTEL_NEW }, -- cgit v1.2.3-59-g8ed1b From ca5b50501d6486bfbb73a07ed8b8821fb31dc065 Mon Sep 17 00:00:00 2001 From: Takashi Sakamoto Date: Sat, 21 Feb 2015 11:50:17 +0900 Subject: ALSA: firewire-lib: fix an unexpected byte sequence for micro sign The sign for microsecond (U+0085, MICRO SIGN) was encoded to '0x c2 b5' by UTF-8 character encoding scheme. But the byte sequence was converted to '0x c3 82 c2 b5' in a previous commit. As a result, the byte sequence cannot represent microsecond sign in UTF-8 or ASCII. This may confuse developers. This commit replaces the sign to string expression with 'microseconds' to purge superfluous troubles. Fixes: 5c697e5b46ef("ALSA: firewire-lib: remove rx_blocks_for_midi quirk") Signed-off-by: Takashi Sakamoto Signed-off-by: Takashi Iwai --- sound/firewire/amdtp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/firewire/amdtp.c b/sound/firewire/amdtp.c index 0d580186ef1a..7b7b18303cac 100644 --- a/sound/firewire/amdtp.c +++ b/sound/firewire/amdtp.c @@ -33,7 +33,7 @@ */ #define MAX_MIDI_RX_BLOCKS 8 -#define TRANSFER_DELAY_TICKS 0x2e00 /* 479.17 µs */ +#define TRANSFER_DELAY_TICKS 0x2e00 /* 479.17 microseconds */ /* isochronous header parameters */ #define ISO_DATA_LENGTH_SHIFT 16 -- cgit v1.2.3-59-g8ed1b From 6426460e5d87810e042962281fe3c1e8fc256162 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 19 Feb 2015 13:01:37 +0100 Subject: ALSA: hda - Add pin configs for ASUS mobo with IDT 92HD73XX codec BIOS doesn't seem to set up pins for 5.1 and the SPDIF out, so we need to give explicitly here. Reported-and-tested-by: Misan Thropos Cc: Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_sigmatel.c | 17 ++++++++++++++++- 1 file changed, 16 insertions(+), 1 deletion(-) diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index 6d36c5b78805..87eff3173ce9 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -79,6 +79,7 @@ enum { STAC_ALIENWARE_M17X, STAC_92HD89XX_HP_FRONT_JACK, STAC_92HD89XX_HP_Z1_G2_RIGHT_MIC_JACK, + STAC_92HD73XX_ASUS_MOBO, STAC_92HD73XX_MODELS }; @@ -1911,7 +1912,18 @@ static const struct hda_fixup stac92hd73xx_fixups[] = { [STAC_92HD89XX_HP_Z1_G2_RIGHT_MIC_JACK] = { .type = HDA_FIXUP_PINS, .v.pins = stac92hd89xx_hp_z1_g2_right_mic_jack_pin_configs, - } + }, + [STAC_92HD73XX_ASUS_MOBO] = { + .type = HDA_FIXUP_PINS, + .v.pins = (const struct hda_pintbl[]) { + /* enable 5.1 and SPDIF out */ + { 0x0c, 0x01014411 }, + { 0x0d, 0x01014410 }, + { 0x0e, 0x01014412 }, + { 0x22, 0x014b1180 }, + { } + } + }, }; static const struct hda_model_fixup stac92hd73xx_models[] = { @@ -1923,6 +1935,7 @@ static const struct hda_model_fixup stac92hd73xx_models[] = { { .id = STAC_DELL_M6_BOTH, .name = "dell-m6" }, { .id = STAC_DELL_EQ, .name = "dell-eq" }, { .id = STAC_ALIENWARE_M17X, .name = "alienware" }, + { .id = STAC_92HD73XX_ASUS_MOBO, .name = "asus-mobo" }, {} }; @@ -1975,6 +1988,8 @@ static const struct snd_pci_quirk stac92hd73xx_fixup_tbl[] = { "HP Z1 G2", STAC_92HD89XX_HP_Z1_G2_RIGHT_MIC_JACK), SND_PCI_QUIRK(PCI_VENDOR_ID_HP, 0x2b17, "unknown HP", STAC_92HD89XX_HP_FRONT_JACK), + SND_PCI_QUIRK(PCI_VENDOR_ID_ASUSTEK, 0x83f8, "ASUS AT4NM10", + STAC_92HD73XX_ASUS_MOBO), {} /* terminator */ }; -- cgit v1.2.3-59-g8ed1b From 12ed719291a953d443921f9cdb0ffee41066c340 Mon Sep 17 00:00:00 2001 From: Takashi Sakamoto Date: Sat, 21 Feb 2015 23:54:57 +0900 Subject: ALSA: fireworks/bebob/dice/oxfw: add reference-counting for FireWire unit Fireworks and Dice drivers try to touch instances of FireWire unit after sound card object is released, while references to the unit is decremented in .remove(). When unplugging during streaming, sound card object is released after .remove(), thus Fireworks and Dice drivers causes GPF or Null-pointer-dereferencing to application processes because an instance of FireWire unit was already released. This commit adds reference-counting for FireWire unit in drivers to allow them to touch an instance of FireWire unit after .remove(). In most case, any operations after .remove() may be failed safely. Signed-off-by: Takashi Sakamoto Cc: # 3.19+ Signed-off-by: Takashi Iwai --- sound/firewire/bebob/bebob.c | 12 +++++++++++- sound/firewire/dice/dice.c | 11 ++++++++++- sound/firewire/fireworks/fireworks.c | 12 +++++++++++- sound/firewire/oxfw/oxfw.c | 11 ++++++++++- 4 files changed, 42 insertions(+), 4 deletions(-) diff --git a/sound/firewire/bebob/bebob.c b/sound/firewire/bebob/bebob.c index fc19c99654aa..b612599fb543 100644 --- a/sound/firewire/bebob/bebob.c +++ b/sound/firewire/bebob/bebob.c @@ -116,11 +116,19 @@ end: return err; } +/* + * This module releases the FireWire unit data after all ALSA character devices + * are released by applications. This is for releasing stream data or finishing + * transactions safely. Thus at returning from .remove(), this module still keep + * references for the unit. + */ static void bebob_card_free(struct snd_card *card) { struct snd_bebob *bebob = card->private_data; + fw_unit_put(bebob->unit); + if (bebob->card_index >= 0) { mutex_lock(&devices_mutex); clear_bit(bebob->card_index, devices_used); @@ -205,7 +213,7 @@ bebob_probe(struct fw_unit *unit, card->private_free = bebob_card_free; bebob->card = card; - bebob->unit = unit; + bebob->unit = fw_unit_get(unit); bebob->spec = spec; mutex_init(&bebob->mutex); spin_lock_init(&bebob->lock); @@ -310,6 +318,8 @@ static void bebob_remove(struct fw_unit *unit) snd_bebob_stream_destroy_duplex(bebob); snd_card_disconnect(bebob->card); + + /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(bebob->card); } diff --git a/sound/firewire/dice/dice.c b/sound/firewire/dice/dice.c index 90d8f40ff727..797f0726fc74 100644 --- a/sound/firewire/dice/dice.c +++ b/sound/firewire/dice/dice.c @@ -226,11 +226,19 @@ static void dice_card_strings(struct snd_dice *dice) strcpy(card->mixername, "DICE"); } +/* + * This module releases the FireWire unit data after all ALSA character devices + * are released by applications. This is for releasing stream data or finishing + * transactions safely. Thus at returning from .remove(), this module still keep + * references for the unit. + */ static void dice_card_free(struct snd_card *card) { struct snd_dice *dice = card->private_data; snd_dice_transaction_destroy(dice); + fw_unit_put(dice->unit); + mutex_destroy(&dice->mutex); } @@ -251,7 +259,7 @@ static int dice_probe(struct fw_unit *unit, const struct ieee1394_device_id *id) dice = card->private_data; dice->card = card; - dice->unit = unit; + dice->unit = fw_unit_get(unit); card->private_free = dice_card_free; spin_lock_init(&dice->lock); @@ -309,6 +317,7 @@ static void dice_remove(struct fw_unit *unit) snd_dice_stream_destroy_duplex(dice); + /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(dice->card); } diff --git a/sound/firewire/fireworks/fireworks.c b/sound/firewire/fireworks/fireworks.c index 3e2ed8e82cbc..1e33394d8a93 100644 --- a/sound/firewire/fireworks/fireworks.c +++ b/sound/firewire/fireworks/fireworks.c @@ -173,11 +173,19 @@ end: return err; } +/* + * This module releases the FireWire unit data after all ALSA character devices + * are released by applications. This is for releasing stream data or finishing + * transactions safely. Thus at returning from .remove(), this module still keep + * references for the unit. + */ static void efw_card_free(struct snd_card *card) { struct snd_efw *efw = card->private_data; + fw_unit_put(efw->unit); + if (efw->card_index >= 0) { mutex_lock(&devices_mutex); clear_bit(efw->card_index, devices_used); @@ -218,7 +226,7 @@ efw_probe(struct fw_unit *unit, card->private_free = efw_card_free; efw->card = card; - efw->unit = unit; + efw->unit = fw_unit_get(unit); mutex_init(&efw->mutex); spin_lock_init(&efw->lock); init_waitqueue_head(&efw->hwdep_wait); @@ -293,6 +301,8 @@ static void efw_remove(struct fw_unit *unit) snd_efw_transaction_remove_instance(efw); snd_card_disconnect(efw->card); + + /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(efw->card); } diff --git a/sound/firewire/oxfw/oxfw.c b/sound/firewire/oxfw/oxfw.c index 60e5cad0531a..1607b26404c3 100644 --- a/sound/firewire/oxfw/oxfw.c +++ b/sound/firewire/oxfw/oxfw.c @@ -104,11 +104,19 @@ end: return err; } +/* + * This module releases the FireWire unit data after all ALSA character devices + * are released by applications. This is for releasing stream data or finishing + * transactions safely. Thus at returning from .remove(), this module still keep + * references for the unit. + */ static void oxfw_card_free(struct snd_card *card) { struct snd_oxfw *oxfw = card->private_data; unsigned int i; + fw_unit_put(oxfw->unit); + for (i = 0; i < SND_OXFW_STREAM_FORMAT_ENTRIES; i++) { kfree(oxfw->tx_stream_formats[i]); kfree(oxfw->rx_stream_formats[i]); @@ -136,7 +144,7 @@ static int oxfw_probe(struct fw_unit *unit, oxfw = card->private_data; oxfw->card = card; mutex_init(&oxfw->mutex); - oxfw->unit = unit; + oxfw->unit = fw_unit_get(unit); oxfw->device_info = (const struct device_info *)id->driver_data; spin_lock_init(&oxfw->lock); init_waitqueue_head(&oxfw->hwdep_wait); @@ -218,6 +226,7 @@ static void oxfw_remove(struct fw_unit *unit) if (oxfw->has_output) snd_oxfw_stream_destroy_simplex(oxfw, &oxfw->tx_stream); + /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(oxfw->card); } -- cgit v1.2.3-59-g8ed1b From c6f224dc20ad959175c2dfec70b5a61c6503a793 Mon Sep 17 00:00:00 2001 From: Takashi Sakamoto Date: Sat, 21 Feb 2015 23:54:58 +0900 Subject: ALSA: firewire-lib: remove reference counting AMDTP helper functions increment/decrement reference counter for an instance of FireWire unit, while it's complicated for each driver to process error state. In previous commit, each driver has the role of reference counting. This commit removes this role from the helper function. Signed-off-by: Takashi Sakamoto Cc: # 3.19+ Signed-off-by: Takashi Iwai --- sound/firewire/amdtp.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/sound/firewire/amdtp.c b/sound/firewire/amdtp.c index 7b7b18303cac..5cc356db5351 100644 --- a/sound/firewire/amdtp.c +++ b/sound/firewire/amdtp.c @@ -78,7 +78,7 @@ static void pcm_period_tasklet(unsigned long data); int amdtp_stream_init(struct amdtp_stream *s, struct fw_unit *unit, enum amdtp_stream_direction dir, enum cip_flags flags) { - s->unit = fw_unit_get(unit); + s->unit = unit; s->direction = dir; s->flags = flags; s->context = ERR_PTR(-1); @@ -102,7 +102,6 @@ void amdtp_stream_destroy(struct amdtp_stream *s) { WARN_ON(amdtp_stream_running(s)); mutex_destroy(&s->mutex); - fw_unit_put(s->unit); } EXPORT_SYMBOL(amdtp_stream_destroy); -- cgit v1.2.3-59-g8ed1b From d23c2cc4485d10f0cedfef99dd2961d9652b1b3f Mon Sep 17 00:00:00 2001 From: Takashi Sakamoto Date: Sat, 21 Feb 2015 23:54:59 +0900 Subject: ALSA: fireworks/bebob/dice/oxfw: allow stream destructor after releasing runtime Currently stream destructor in each driver has a problem to be called in a context in which sound card object is released, because the destructors call amdtp_stream_pcm_abort() and touch PCM runtime data. The PCM runtime data is destroyed in application's context with snd_pcm_close(), on the other hand PCM substream data is destroyed after sound card object is released, in most case after all of ALSA character devices are released. When PCM runtime is destroyed and PCM substream is remained, amdtp_stream_pcm_abort() touches PCM runtime data and causes Null-pointer-dereference. This commit changes stream destructors and allows each driver to call it after releasing runtime. Signed-off-by: Takashi Sakamoto Cc: # 3.19+ Signed-off-by: Takashi Iwai --- sound/firewire/bebob/bebob_stream.c | 12 ++++-------- sound/firewire/dice/dice-stream.c | 18 ++++++++++++------ sound/firewire/fireworks/fireworks_stream.c | 15 ++++++++++----- sound/firewire/oxfw/oxfw-stream.c | 6 ++++-- 4 files changed, 30 insertions(+), 21 deletions(-) diff --git a/sound/firewire/bebob/bebob_stream.c b/sound/firewire/bebob/bebob_stream.c index 0ebcabfdc7ce..fcca3eebc91f 100644 --- a/sound/firewire/bebob/bebob_stream.c +++ b/sound/firewire/bebob/bebob_stream.c @@ -410,8 +410,6 @@ break_both_connections(struct snd_bebob *bebob) static void destroy_both_connections(struct snd_bebob *bebob) { - break_both_connections(bebob); - cmp_connection_destroy(&bebob->in_conn); cmp_connection_destroy(&bebob->out_conn); } @@ -712,16 +710,14 @@ void snd_bebob_stream_update_duplex(struct snd_bebob *bebob) mutex_unlock(&bebob->mutex); } +/* + * This function should be called before starting streams or after stopping + * streams. + */ void snd_bebob_stream_destroy_duplex(struct snd_bebob *bebob) { mutex_lock(&bebob->mutex); - amdtp_stream_pcm_abort(&bebob->rx_stream); - amdtp_stream_pcm_abort(&bebob->tx_stream); - - amdtp_stream_stop(&bebob->rx_stream); - amdtp_stream_stop(&bebob->tx_stream); - amdtp_stream_destroy(&bebob->rx_stream); amdtp_stream_destroy(&bebob->tx_stream); diff --git a/sound/firewire/dice/dice-stream.c b/sound/firewire/dice/dice-stream.c index fa9cf761b610..07dbd01d7a6b 100644 --- a/sound/firewire/dice/dice-stream.c +++ b/sound/firewire/dice/dice-stream.c @@ -311,14 +311,21 @@ end: return err; } +/* + * This function should be called before starting streams or after stopping + * streams. + */ static void destroy_stream(struct snd_dice *dice, struct amdtp_stream *stream) { - amdtp_stream_destroy(stream); + struct fw_iso_resources *resources; if (stream == &dice->tx_stream) - fw_iso_resources_destroy(&dice->tx_resources); + resources = &dice->tx_resources; else - fw_iso_resources_destroy(&dice->rx_resources); + resources = &dice->rx_resources; + + amdtp_stream_destroy(stream); + fw_iso_resources_destroy(resources); } int snd_dice_stream_init_duplex(struct snd_dice *dice) @@ -332,6 +339,8 @@ int snd_dice_stream_init_duplex(struct snd_dice *dice) goto end; err = init_stream(dice, &dice->rx_stream); + if (err < 0) + destroy_stream(dice, &dice->tx_stream); end: return err; } @@ -340,10 +349,7 @@ void snd_dice_stream_destroy_duplex(struct snd_dice *dice) { snd_dice_transaction_clear_enable(dice); - stop_stream(dice, &dice->tx_stream); destroy_stream(dice, &dice->tx_stream); - - stop_stream(dice, &dice->rx_stream); destroy_stream(dice, &dice->rx_stream); dice->substreams_counter = 0; diff --git a/sound/firewire/fireworks/fireworks_stream.c b/sound/firewire/fireworks/fireworks_stream.c index 4f440e163667..f817b7ae097e 100644 --- a/sound/firewire/fireworks/fireworks_stream.c +++ b/sound/firewire/fireworks/fireworks_stream.c @@ -100,17 +100,22 @@ end: return err; } +/* + * This function should be called before starting the stream or after stopping + * the streams. + */ static void destroy_stream(struct snd_efw *efw, struct amdtp_stream *stream) { - stop_stream(efw, stream); - - amdtp_stream_destroy(stream); + struct cmp_connection *conn; if (stream == &efw->tx_stream) - cmp_connection_destroy(&efw->out_conn); + conn = &efw->out_conn; else - cmp_connection_destroy(&efw->in_conn); + conn = &efw->in_conn; + + amdtp_stream_destroy(stream); + cmp_connection_destroy(&efw->out_conn); } static int diff --git a/sound/firewire/oxfw/oxfw-stream.c b/sound/firewire/oxfw/oxfw-stream.c index bda845afb470..29ccb3637164 100644 --- a/sound/firewire/oxfw/oxfw-stream.c +++ b/sound/firewire/oxfw/oxfw-stream.c @@ -337,6 +337,10 @@ void snd_oxfw_stream_stop_simplex(struct snd_oxfw *oxfw, stop_stream(oxfw, stream); } +/* + * This function should be called before starting the stream or after stopping + * the streams. + */ void snd_oxfw_stream_destroy_simplex(struct snd_oxfw *oxfw, struct amdtp_stream *stream) { @@ -347,8 +351,6 @@ void snd_oxfw_stream_destroy_simplex(struct snd_oxfw *oxfw, else conn = &oxfw->in_conn; - stop_stream(oxfw, stream); - amdtp_stream_destroy(stream); cmp_connection_destroy(conn); } -- cgit v1.2.3-59-g8ed1b From dec84316dd53c90e93b4ee849483bd4bd1e9a585 Mon Sep 17 00:00:00 2001 From: Takashi Sakamoto Date: Sat, 21 Feb 2015 23:55:00 +0900 Subject: ALSA: fireworks/bebob/dice/oxfw: make it possible to shutdown safely A part of these drivers, especially BeBoB driver, are programmed to wait some events. Thus the drivers should not destroy any data in .remove() context. This commit moves some destructors from 'struct fw_driver.remove()' to 'struct snd_card.private_free()' to shutdown safely. Signed-off-by: Takashi Sakamoto Cc: # 3.19+ Signed-off-by: Takashi Iwai --- sound/firewire/bebob/bebob.c | 10 ++++++---- sound/firewire/bebob/bebob_stream.c | 4 ---- sound/firewire/dice/dice.c | 5 +---- sound/firewire/fireworks/fireworks.c | 10 ++++------ sound/firewire/fireworks/fireworks_stream.c | 4 ---- sound/firewire/oxfw/oxfw.c | 10 ++++------ 6 files changed, 15 insertions(+), 28 deletions(-) diff --git a/sound/firewire/bebob/bebob.c b/sound/firewire/bebob/bebob.c index b612599fb543..611b7dae7ee5 100644 --- a/sound/firewire/bebob/bebob.c +++ b/sound/firewire/bebob/bebob.c @@ -127,8 +127,11 @@ bebob_card_free(struct snd_card *card) { struct snd_bebob *bebob = card->private_data; + snd_bebob_stream_destroy_duplex(bebob); fw_unit_put(bebob->unit); + kfree(bebob->maudio_special_quirk); + if (bebob->card_index >= 0) { mutex_lock(&devices_mutex); clear_bit(bebob->card_index, devices_used); @@ -314,10 +317,9 @@ static void bebob_remove(struct fw_unit *unit) if (bebob == NULL) return; - kfree(bebob->maudio_special_quirk); - - snd_bebob_stream_destroy_duplex(bebob); - snd_card_disconnect(bebob->card); + /* Awake bus-reset waiters. */ + if (!completion_done(&bebob->bus_reset)) + complete_all(&bebob->bus_reset); /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(bebob->card); diff --git a/sound/firewire/bebob/bebob_stream.c b/sound/firewire/bebob/bebob_stream.c index fcca3eebc91f..98e4fc8121a1 100644 --- a/sound/firewire/bebob/bebob_stream.c +++ b/sound/firewire/bebob/bebob_stream.c @@ -716,14 +716,10 @@ void snd_bebob_stream_update_duplex(struct snd_bebob *bebob) */ void snd_bebob_stream_destroy_duplex(struct snd_bebob *bebob) { - mutex_lock(&bebob->mutex); - amdtp_stream_destroy(&bebob->rx_stream); amdtp_stream_destroy(&bebob->tx_stream); destroy_both_connections(bebob); - - mutex_unlock(&bebob->mutex); } /* diff --git a/sound/firewire/dice/dice.c b/sound/firewire/dice/dice.c index 797f0726fc74..70a111d7f428 100644 --- a/sound/firewire/dice/dice.c +++ b/sound/firewire/dice/dice.c @@ -236,6 +236,7 @@ static void dice_card_free(struct snd_card *card) { struct snd_dice *dice = card->private_data; + snd_dice_stream_destroy_duplex(dice); snd_dice_transaction_destroy(dice); fw_unit_put(dice->unit); @@ -313,10 +314,6 @@ static void dice_remove(struct fw_unit *unit) { struct snd_dice *dice = dev_get_drvdata(&unit->device); - snd_card_disconnect(dice->card); - - snd_dice_stream_destroy_duplex(dice); - /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(dice->card); } diff --git a/sound/firewire/fireworks/fireworks.c b/sound/firewire/fireworks/fireworks.c index 1e33394d8a93..2682e7e3e5c9 100644 --- a/sound/firewire/fireworks/fireworks.c +++ b/sound/firewire/fireworks/fireworks.c @@ -184,8 +184,12 @@ efw_card_free(struct snd_card *card) { struct snd_efw *efw = card->private_data; + snd_efw_stream_destroy_duplex(efw); + snd_efw_transaction_remove_instance(efw); fw_unit_put(efw->unit); + kfree(efw->resp_buf); + if (efw->card_index >= 0) { mutex_lock(&devices_mutex); clear_bit(efw->card_index, devices_used); @@ -193,7 +197,6 @@ efw_card_free(struct snd_card *card) } mutex_destroy(&efw->mutex); - kfree(efw->resp_buf); } static int @@ -297,11 +300,6 @@ static void efw_remove(struct fw_unit *unit) { struct snd_efw *efw = dev_get_drvdata(&unit->device); - snd_efw_stream_destroy_duplex(efw); - snd_efw_transaction_remove_instance(efw); - - snd_card_disconnect(efw->card); - /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(efw->card); } diff --git a/sound/firewire/fireworks/fireworks_stream.c b/sound/firewire/fireworks/fireworks_stream.c index f817b7ae097e..c55db1bddc80 100644 --- a/sound/firewire/fireworks/fireworks_stream.c +++ b/sound/firewire/fireworks/fireworks_stream.c @@ -324,12 +324,8 @@ void snd_efw_stream_update_duplex(struct snd_efw *efw) void snd_efw_stream_destroy_duplex(struct snd_efw *efw) { - mutex_lock(&efw->mutex); - destroy_stream(efw, &efw->rx_stream); destroy_stream(efw, &efw->tx_stream); - - mutex_unlock(&efw->mutex); } void snd_efw_stream_lock_changed(struct snd_efw *efw) diff --git a/sound/firewire/oxfw/oxfw.c b/sound/firewire/oxfw/oxfw.c index 1607b26404c3..8c6ce019f437 100644 --- a/sound/firewire/oxfw/oxfw.c +++ b/sound/firewire/oxfw/oxfw.c @@ -115,6 +115,10 @@ static void oxfw_card_free(struct snd_card *card) struct snd_oxfw *oxfw = card->private_data; unsigned int i; + snd_oxfw_stream_destroy_simplex(oxfw, &oxfw->rx_stream); + if (oxfw->has_output) + snd_oxfw_stream_destroy_simplex(oxfw, &oxfw->tx_stream); + fw_unit_put(oxfw->unit); for (i = 0; i < SND_OXFW_STREAM_FORMAT_ENTRIES; i++) { @@ -220,12 +224,6 @@ static void oxfw_remove(struct fw_unit *unit) { struct snd_oxfw *oxfw = dev_get_drvdata(&unit->device); - snd_card_disconnect(oxfw->card); - - snd_oxfw_stream_destroy_simplex(oxfw, &oxfw->rx_stream); - if (oxfw->has_output) - snd_oxfw_stream_destroy_simplex(oxfw, &oxfw->tx_stream); - /* No need to wait for releasing card object in this context. */ snd_card_free_when_closed(oxfw->card); } -- cgit v1.2.3-59-g8ed1b From 1365aa6266fad0669487240af3f098593796172c Mon Sep 17 00:00:00 2001 From: Oded Gabbay Date: Tue, 17 Feb 2015 11:58:27 +0200 Subject: drm/amdkfd: Initialize only amdkfd's assigned pipelines MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This patch fixes a bug in the initialization of the pipelines. The init_pipelines() function was called with a constant value of 0 in the first_pipe argument. This is an error because amdkfd doesn't handle pipe 0. The correct way is to pass the value that get_first_pipe() returns as the argument for first_pipe. This bug appeared in 3.19 (first version with amdkfd) and it causes around 15% drop in CPU performance of Kaveri (A10-7850). v2: Don't set get_first_pipe() as inline because it calls BUG_ON() Signed-off-by: Oded Gabbay Cc: stable@vger.kernel.org Tested-by: Michel Dänzer --- drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c | 4 ++-- drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h | 1 + drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager_cik.c | 2 +- 3 files changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c index b3589d0e39b9..1b58f331afee 100644 --- a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c +++ b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c @@ -62,9 +62,9 @@ enum KFD_MQD_TYPE get_mqd_type_from_queue_type(enum kfd_queue_type type) return KFD_MQD_TYPE_CP; } -static inline unsigned int get_first_pipe(struct device_queue_manager *dqm) +unsigned int get_first_pipe(struct device_queue_manager *dqm) { - BUG_ON(!dqm); + BUG_ON(!dqm || !dqm->dev); return dqm->dev->shared_resources.first_compute_pipe; } diff --git a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h index d64f86cda34f..386bd7df7c30 100644 --- a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h +++ b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h @@ -163,6 +163,7 @@ void program_sh_mem_settings(struct device_queue_manager *dqm, struct qcm_process_device *qpd); int init_pipelines(struct device_queue_manager *dqm, unsigned int pipes_num, unsigned int first_pipe); +unsigned int get_first_pipe(struct device_queue_manager *dqm); extern inline unsigned int get_sh_mem_bases_32(struct kfd_process_device *pdd) { diff --git a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager_cik.c b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager_cik.c index 6b072466e2a6..5469efe0523e 100644 --- a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager_cik.c +++ b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager_cik.c @@ -131,5 +131,5 @@ static int register_process_cik(struct device_queue_manager *dqm, static int initialize_cpsch_cik(struct device_queue_manager *dqm) { - return init_pipelines(dqm, get_pipes_num(dqm), 0); + return init_pipelines(dqm, get_pipes_num(dqm), get_first_pipe(dqm)); } -- cgit v1.2.3-59-g8ed1b From 64ea8f4af57cee9f8b0bf542819b41ee82acfcb9 Mon Sep 17 00:00:00 2001 From: Oded Gabbay Date: Tue, 17 Feb 2015 11:30:31 +0200 Subject: drm/amdkfd: don't set get_pipes_num() as inline get_pipes_num() calls BUG_ON so we can't set it as inline because it produces a warning as BUG_ON() uses static variables when it is expanded. Signed-off-by: Oded Gabbay --- drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c | 6 ++++++ drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h | 7 +------ 2 files changed, 7 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c index 1b58f331afee..910ff8ab9c9c 100644 --- a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c +++ b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c @@ -68,6 +68,12 @@ unsigned int get_first_pipe(struct device_queue_manager *dqm) return dqm->dev->shared_resources.first_compute_pipe; } +unsigned int get_pipes_num(struct device_queue_manager *dqm) +{ + BUG_ON(!dqm || !dqm->dev); + return dqm->dev->shared_resources.compute_pipe_count; +} + static inline unsigned int get_pipes_num_cpsch(void) { return PIPE_PER_ME_CP_SCHEDULING; diff --git a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h index 386bd7df7c30..488f51d19427 100644 --- a/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h +++ b/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h @@ -164,6 +164,7 @@ void program_sh_mem_settings(struct device_queue_manager *dqm, int init_pipelines(struct device_queue_manager *dqm, unsigned int pipes_num, unsigned int first_pipe); unsigned int get_first_pipe(struct device_queue_manager *dqm); +unsigned int get_pipes_num(struct device_queue_manager *dqm); extern inline unsigned int get_sh_mem_bases_32(struct kfd_process_device *pdd) { @@ -176,10 +177,4 @@ get_sh_mem_bases_nybble_64(struct kfd_process_device *pdd) return (pdd->lds_base >> 60) & 0x0E; } -extern inline unsigned int get_pipes_num(struct device_queue_manager *dqm) -{ - BUG_ON(!dqm || !dqm->dev); - return dqm->dev->shared_resources.compute_pipe_count; -} - #endif /* KFD_DEVICE_QUEUE_MANAGER_H_ */ -- cgit v1.2.3-59-g8ed1b From d0d62230185e9d1a683bfa5cdfe5e520577f68d1 Mon Sep 17 00:00:00 2001 From: Pratyush Anand Date: Fri, 13 Feb 2015 04:06:21 +0000 Subject: arm64: ftrace: fix ftrace_modify_graph_caller for branch replace ftrace_enable_ftrace_graph_caller and ftrace_disable_ftrace_graph_caller should replace B(jmp) instruction and not BL(call) instruction. Commit 9f1ae7596aad("arm64: Correct ftrace calls to aarch64_insn_gen_branch_imm()") had a typo and used AARCH64_INSN_BRANCH_LINK instead of AARCH64_INSN_BRANCH_NOLINK. Either instruction will work, as the link register is saved/restored across the branch but this better matches the intention of the code. Signed-off-by: Pratyush Anand Signed-off-by: Will Deacon --- arch/arm64/kernel/ftrace.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/kernel/ftrace.c b/arch/arm64/kernel/ftrace.c index cf8556ae09d0..c851be795080 100644 --- a/arch/arm64/kernel/ftrace.c +++ b/arch/arm64/kernel/ftrace.c @@ -156,7 +156,7 @@ static int ftrace_modify_graph_caller(bool enable) branch = aarch64_insn_gen_branch_imm(pc, (unsigned long)ftrace_graph_caller, - AARCH64_INSN_BRANCH_LINK); + AARCH64_INSN_BRANCH_NOLINK); nop = aarch64_insn_gen_nop(); if (enable) -- cgit v1.2.3-59-g8ed1b From 115386f89b5415fcdf641faad0d459cd5c07d225 Mon Sep 17 00:00:00 2001 From: Robin Murphy Date: Wed, 18 Feb 2015 15:40:17 +0000 Subject: arm64: insn: fix compare-and-branch encodings Fix cbz/cbnz having the mask offset by a bit, and add encodings for tbz/tbnz so that all branch forms are represented. Signed-off-by: Robin Murphy Acked-by: Will Deacon Acked-by: Zi Shen Lim Signed-off-by: Will Deacon --- arch/arm64/include/asm/insn.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/arm64/include/asm/insn.h b/arch/arm64/include/asm/insn.h index e2ff32a93b5c..d2f49423c5dc 100644 --- a/arch/arm64/include/asm/insn.h +++ b/arch/arm64/include/asm/insn.h @@ -264,8 +264,10 @@ __AARCH64_INSN_FUNCS(ands, 0x7F200000, 0x6A000000) __AARCH64_INSN_FUNCS(bics, 0x7F200000, 0x6A200000) __AARCH64_INSN_FUNCS(b, 0xFC000000, 0x14000000) __AARCH64_INSN_FUNCS(bl, 0xFC000000, 0x94000000) -__AARCH64_INSN_FUNCS(cbz, 0xFE000000, 0x34000000) -__AARCH64_INSN_FUNCS(cbnz, 0xFE000000, 0x35000000) +__AARCH64_INSN_FUNCS(cbz, 0x7F000000, 0x34000000) +__AARCH64_INSN_FUNCS(cbnz, 0x7F000000, 0x35000000) +__AARCH64_INSN_FUNCS(tbz, 0x7F000000, 0x36000000) +__AARCH64_INSN_FUNCS(tbnz, 0x7F000000, 0x37000000) __AARCH64_INSN_FUNCS(bcond, 0xFF000010, 0x54000000) __AARCH64_INSN_FUNCS(svc, 0xFFE0001F, 0xD4000001) __AARCH64_INSN_FUNCS(hvc, 0xFFE0001F, 0xD4000002) -- cgit v1.2.3-59-g8ed1b From f3e39273e0a9a5c9dc78cd667ec3663e97e0e989 Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Fri, 20 Feb 2015 13:53:13 +0000 Subject: arm64: guard asm/assembler.h against multiple inclusions asm/assembler.h lacks the usual guard against multiple inclusion, leading to a compilation failure if it is accidentally included twice. Using the classic #ifndef/#define/#endif construct solves the issue. Signed-off-by: Marc Zyngier Signed-off-by: Will Deacon --- arch/arm64/include/asm/assembler.h | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm64/include/asm/assembler.h b/arch/arm64/include/asm/assembler.h index 5901480bfdca..750bac4e637e 100644 --- a/arch/arm64/include/asm/assembler.h +++ b/arch/arm64/include/asm/assembler.h @@ -20,6 +20,9 @@ #error "Only include this from assembly code" #endif +#ifndef __ASM_ASSEMBLER_H +#define __ASM_ASSEMBLER_H + #include #include @@ -155,3 +158,5 @@ lr .req x30 // link register #endif orr \rd, \lbits, \hbits, lsl #32 .endm + +#endif /* __ASM_ASSEMBLER_H */ -- cgit v1.2.3-59-g8ed1b From 0dc6f20b9803f09726bbb682649d35cda8ef5b5d Mon Sep 17 00:00:00 2001 From: Rodrigo Vivi Date: Wed, 21 Jan 2015 11:46:32 -0800 Subject: drm/i915/bdw: PCI IDs ending in 0xb are ULT. When reviewing patch that fixes VGA on BDW Halo Jani noticed that we also had other ULT IDs that weren't listed there. So this follow-up patch add these pci-ids as halo and fix comments on i915_pciids.h Cc: Jani Nikula Cc: stable@vger.kernel.org Signed-off-by: Rodrigo Vivi Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/i915_drv.h | 1 + include/drm/i915_pciids.h | 4 ++-- 2 files changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index f2a825e39646..b38c770a22f5 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -2374,6 +2374,7 @@ struct drm_i915_cmd_table { (INTEL_DEVID(dev) & 0xFF00) == 0x0C00) #define IS_BDW_ULT(dev) (IS_BROADWELL(dev) && \ ((INTEL_DEVID(dev) & 0xf) == 0x6 || \ + (INTEL_DEVID(dev) & 0xf) == 0xb || \ (INTEL_DEVID(dev) & 0xf) == 0xe)) #define IS_BDW_GT3(dev) (IS_BROADWELL(dev) && \ (INTEL_DEVID(dev) & 0x00F0) == 0x0020) diff --git a/include/drm/i915_pciids.h b/include/drm/i915_pciids.h index 180ad0e6de21..d016dc57f007 100644 --- a/include/drm/i915_pciids.h +++ b/include/drm/i915_pciids.h @@ -214,9 +214,9 @@ INTEL_VGA_DEVICE((((gt) - 1) << 4) | (id), info) #define _INTEL_BDW_M_IDS(gt, info) \ - _INTEL_BDW_M(gt, 0x1602, info), /* ULT */ \ + _INTEL_BDW_M(gt, 0x1602, info), /* Halo */ \ _INTEL_BDW_M(gt, 0x1606, info), /* ULT */ \ - _INTEL_BDW_M(gt, 0x160B, info), /* Iris */ \ + _INTEL_BDW_M(gt, 0x160B, info), /* ULT */ \ _INTEL_BDW_M(gt, 0x160E, info) /* ULX */ #define _INTEL_BDW_D_IDS(gt, info) \ -- cgit v1.2.3-59-g8ed1b From 8b402c929d21a18e9a228d4ad6f0a076577cd63c Mon Sep 17 00:00:00 2001 From: Jiri Kosina Date: Mon, 23 Feb 2015 11:15:44 +0100 Subject: HID: sony: initialize sony_dev_list_lock properly sony_dev_list_lock spinlock (which was introduced in d2d782fccee ("HID: sony: Prevent duplicate controller connections") is not being initialized properly. Fix that. Reported-by: Pavel Machek Signed-off-by: Jiri Kosina --- drivers/hid/hid-sony.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hid/hid-sony.c b/drivers/hid/hid-sony.c index 38d8af558d72..e87148dbeb1b 100644 --- a/drivers/hid/hid-sony.c +++ b/drivers/hid/hid-sony.c @@ -804,7 +804,7 @@ union sixaxis_output_report_01 { #define DS4_REPORT_0x81_SIZE 7 #define SIXAXIS_REPORT_0xF2_SIZE 18 -static spinlock_t sony_dev_list_lock; +static DEFINE_SPINLOCK(sony_dev_list_lock); static LIST_HEAD(sony_device_list); static DEFINE_IDA(sony_device_id_allocator); -- cgit v1.2.3-59-g8ed1b From dfcc70a8c868fe03276fa59864149708fb41930b Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Mon, 23 Feb 2015 22:34:17 +1100 Subject: xfs: Fix quota type in quota structures when reusing quota file For filesystems without separate project quota inode field in the superblock we just reuse project quota file for group quotas (and vice versa) if project quota file is allocated and we need group quota file. When we reuse the file, quota structures on disk suddenly have wrong type stored in d_flags though. Nobody really cares about this (although structure type reported to userspace was wrong as well) except that after commit 14bf61ffe6ac (quota: Switch ->get_dqblk() and ->set_dqblk() to use bytes as space units) assertion in xfs_qm_scall_getquota() started to trigger on xfs/106 test (apparently I was testing without XFS_DEBUG so I didn't notice when submitting the above commit). Fix the problem by properly resetting ddq->d_flags when running quotacheck for a quota file. CC: stable@vger.kernel.org Reported-by: Al Viro Signed-off-by: Jan Kara Reviewed-by: Dave Chinner Signed-off-by: Dave Chinner --- fs/xfs/xfs_qm.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/fs/xfs/xfs_qm.c b/fs/xfs/xfs_qm.c index 53cc2aaf8d2b..fbbb9e62e274 100644 --- a/fs/xfs/xfs_qm.c +++ b/fs/xfs/xfs_qm.c @@ -836,6 +836,11 @@ xfs_qm_reset_dqcounts( */ xfs_dqcheck(mp, ddq, id+j, type, XFS_QMOPT_DQREPAIR, "xfs_quotacheck"); + /* + * Reset type in case we are reusing group quota file for + * project quotas or vice versa + */ + ddq->d_flags = type; ddq->d_bcount = 0; ddq->d_icount = 0; ddq->d_rtbcount = 0; -- cgit v1.2.3-59-g8ed1b From 5885ebda878b47c4b4602d4b0410cb4b282af024 Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Mon, 23 Feb 2015 22:37:08 +1100 Subject: xfs: ensure truncate forces zeroed blocks to disk A new fsync vs power fail test in xfstests indicated that XFS can have unreliable data consistency when doing extending truncates that require block zeroing. The blocks beyond EOF get zeroed in memory, but we never force those changes to disk before we run the transaction that extends the file size and exposes those blocks to userspace. This can result in the blocks not being correctly zeroed after a crash. Because in-memory behaviour is correct, tools like fsx don't pick up any coherency problems - it's not until the filesystem is shutdown or the system crashes after writing the truncate transaction to the journal but before the zeroed data in the page cache is flushed that the issue is exposed. Fix this by also flushing the dirty data in memory region between the old size and new size when we've found blocks that need zeroing in the truncate process. Reported-by: Liu Bo cc: Signed-off-by: Dave Chinner Reviewed-by: Brian Foster Signed-off-by: Dave Chinner --- fs/xfs/xfs_file.c | 14 ++++++++++---- fs/xfs/xfs_inode.h | 9 +++++---- fs/xfs/xfs_iops.c | 36 ++++++++++++++---------------------- 3 files changed, 29 insertions(+), 30 deletions(-) diff --git a/fs/xfs/xfs_file.c b/fs/xfs/xfs_file.c index ce615d12fb44..a2e1cb8a568b 100644 --- a/fs/xfs/xfs_file.c +++ b/fs/xfs/xfs_file.c @@ -397,7 +397,8 @@ STATIC int /* error (positive) */ xfs_zero_last_block( struct xfs_inode *ip, xfs_fsize_t offset, - xfs_fsize_t isize) + xfs_fsize_t isize, + bool *did_zeroing) { struct xfs_mount *mp = ip->i_mount; xfs_fileoff_t last_fsb = XFS_B_TO_FSBT(mp, isize); @@ -425,6 +426,7 @@ xfs_zero_last_block( zero_len = mp->m_sb.sb_blocksize - zero_offset; if (isize + zero_len > offset) zero_len = offset - isize; + *did_zeroing = true; return xfs_iozero(ip, isize, zero_len); } @@ -443,7 +445,8 @@ int /* error (positive) */ xfs_zero_eof( struct xfs_inode *ip, xfs_off_t offset, /* starting I/O offset */ - xfs_fsize_t isize) /* current inode size */ + xfs_fsize_t isize, /* current inode size */ + bool *did_zeroing) { struct xfs_mount *mp = ip->i_mount; xfs_fileoff_t start_zero_fsb; @@ -465,7 +468,7 @@ xfs_zero_eof( * We only zero a part of that block so it is handled specially. */ if (XFS_B_FSB_OFFSET(mp, isize) != 0) { - error = xfs_zero_last_block(ip, offset, isize); + error = xfs_zero_last_block(ip, offset, isize, did_zeroing); if (error) return error; } @@ -525,6 +528,7 @@ xfs_zero_eof( if (error) return error; + *did_zeroing = true; start_zero_fsb = imap.br_startoff + imap.br_blockcount; ASSERT(start_zero_fsb <= (end_zero_fsb + 1)); } @@ -567,13 +571,15 @@ restart: * having to redo all checks before. */ if (*pos > i_size_read(inode)) { + bool zero = false; + if (*iolock == XFS_IOLOCK_SHARED) { xfs_rw_iunlock(ip, *iolock); *iolock = XFS_IOLOCK_EXCL; xfs_rw_ilock(ip, *iolock); goto restart; } - error = xfs_zero_eof(ip, *pos, i_size_read(inode)); + error = xfs_zero_eof(ip, *pos, i_size_read(inode), &zero); if (error) return error; } diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index 86cd6b39bed7..a1cd55f3f351 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -384,10 +384,11 @@ enum xfs_prealloc_flags { XFS_PREALLOC_INVISIBLE = (1 << 4), }; -int xfs_update_prealloc_flags(struct xfs_inode *, - enum xfs_prealloc_flags); -int xfs_zero_eof(struct xfs_inode *, xfs_off_t, xfs_fsize_t); -int xfs_iozero(struct xfs_inode *, loff_t, size_t); +int xfs_update_prealloc_flags(struct xfs_inode *ip, + enum xfs_prealloc_flags flags); +int xfs_zero_eof(struct xfs_inode *ip, xfs_off_t offset, + xfs_fsize_t isize, bool *did_zeroing); +int xfs_iozero(struct xfs_inode *ip, loff_t pos, size_t count); #define IHOLD(ip) \ diff --git a/fs/xfs/xfs_iops.c b/fs/xfs/xfs_iops.c index d919ad7b16bf..e53a90331422 100644 --- a/fs/xfs/xfs_iops.c +++ b/fs/xfs/xfs_iops.c @@ -751,6 +751,7 @@ xfs_setattr_size( int error; uint lock_flags = 0; uint commit_flags = 0; + bool did_zeroing = false; trace_xfs_setattr(ip); @@ -794,20 +795,16 @@ xfs_setattr_size( return error; /* - * Now we can make the changes. Before we join the inode to the - * transaction, take care of the part of the truncation that must be - * done without the inode lock. This needs to be done before joining - * the inode to the transaction, because the inode cannot be unlocked - * once it is a part of the transaction. + * File data changes must be complete before we start the transaction to + * modify the inode. This needs to be done before joining the inode to + * the transaction because the inode cannot be unlocked once it is a + * part of the transaction. + * + * Start with zeroing any data block beyond EOF that we may expose on + * file extension. */ if (newsize > oldsize) { - /* - * Do the first part of growing a file: zero any data in the - * last block that is beyond the old EOF. We need to do this - * before the inode is joined to the transaction to modify - * i_size. - */ - error = xfs_zero_eof(ip, newsize, oldsize); + error = xfs_zero_eof(ip, newsize, oldsize, &did_zeroing); if (error) return error; } @@ -817,23 +814,18 @@ xfs_setattr_size( * any previous writes that are beyond the on disk EOF and the new * EOF that have not been written out need to be written here. If we * do not write the data out, we expose ourselves to the null files - * problem. - * - * Only flush from the on disk size to the smaller of the in memory - * file size or the new size as that's the range we really care about - * here and prevents waiting for other data not within the range we - * care about here. + * problem. Note that this includes any block zeroing we did above; + * otherwise those blocks may not be zeroed after a crash. */ - if (oldsize != ip->i_d.di_size && newsize > ip->i_d.di_size) { + if (newsize > ip->i_d.di_size && + (oldsize != ip->i_d.di_size || did_zeroing)) { error = filemap_write_and_wait_range(VFS_I(ip)->i_mapping, ip->i_d.di_size, newsize); if (error) return error; } - /* - * Wait for all direct I/O to complete. - */ + /* Now wait for all direct I/O to complete. */ inode_dio_wait(inode); /* -- cgit v1.2.3-59-g8ed1b From b94993f6fb3452628bb4678ea86df33ffbfdde8d Mon Sep 17 00:00:00 2001 From: Frank Praznik Date: Sun, 22 Feb 2015 20:42:46 -0500 Subject: HID: sony: fix uninitialized per-controller spinlock Per-controller spinlock needs to be properly initialized during device probe. [jkosina@suse.cz: massage changelog] [jkosina@suse.cz: drop hunk that has already been applied by previous patch] Signed-off-by: Frank Praznik Signed-off-by: Jiri Kosina --- drivers/hid/hid-sony.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/hid/hid-sony.c b/drivers/hid/hid-sony.c index e87148dbeb1b..1896c019e302 100644 --- a/drivers/hid/hid-sony.c +++ b/drivers/hid/hid-sony.c @@ -1944,6 +1944,8 @@ static int sony_probe(struct hid_device *hdev, const struct hid_device_id *id) return -ENOMEM; } + spin_lock_init(&sc->lock); + sc->quirks = quirks; hid_set_drvdata(hdev, sc); sc->hdev = hdev; -- cgit v1.2.3-59-g8ed1b From f75fb42a6164a4c7f5bb6cbaae65555db89904a8 Mon Sep 17 00:00:00 2001 From: Jani Nikula Date: Tue, 10 Feb 2015 13:15:49 +0200 Subject: drm/i915/skl: handle all pixel formats in skylake_update_primary_plane() skylake_update_primary_plane() did not handle all pixel formats returned by skl_format_to_fourcc(). Handle alpha similar to skl_update_plane(). Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89052 Reviewed-by: Damien Lespiau Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/intel_display.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 3d220a67f865..f392e182184b 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -2725,10 +2725,19 @@ static void skylake_update_primary_plane(struct drm_crtc *crtc, case DRM_FORMAT_XRGB8888: plane_ctl |= PLANE_CTL_FORMAT_XRGB_8888; break; + case DRM_FORMAT_ARGB8888: + plane_ctl |= PLANE_CTL_FORMAT_XRGB_8888; + plane_ctl |= PLANE_CTL_ALPHA_SW_PREMULTIPLY; + break; case DRM_FORMAT_XBGR8888: plane_ctl |= PLANE_CTL_ORDER_RGBX; plane_ctl |= PLANE_CTL_FORMAT_XRGB_8888; break; + case DRM_FORMAT_ABGR8888: + plane_ctl |= PLANE_CTL_ORDER_RGBX; + plane_ctl |= PLANE_CTL_FORMAT_XRGB_8888; + plane_ctl |= PLANE_CTL_ALPHA_SW_PREMULTIPLY; + break; case DRM_FORMAT_XRGB2101010: plane_ctl |= PLANE_CTL_FORMAT_XRGB_2101010; break; -- cgit v1.2.3-59-g8ed1b From cf6f0af9fbdd90b81af14fa6375387131cd8adf1 Mon Sep 17 00:00:00 2001 From: Jani Nikula Date: Thu, 19 Feb 2015 10:53:39 +0200 Subject: drm/i915: Dell Chromebook 11 has PWM backlight Add quirk for Dell Chromebook 11 backlight. Reported-and-tested-by: Owen Garland Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93451 Acked-by: Damien Lespiau Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/intel_display.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index f392e182184b..2adedee7e52a 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -13105,6 +13105,9 @@ static struct intel_quirk intel_quirks[] = { /* HP Chromebook 14 (Celeron 2955U) */ { 0x0a06, 0x103c, 0x21ed, quirk_backlight_present }, + + /* Dell Chromebook 11 */ + { 0x0a06, 0x1028, 0x0a35, quirk_backlight_present }, }; static void intel_init_quirks(struct drm_device *dev) -- cgit v1.2.3-59-g8ed1b From 6d00f37e49d95e640a3937a4a1ae07dbe92a10cb Mon Sep 17 00:00:00 2001 From: Seth Forshee Date: Fri, 20 Feb 2015 11:45:11 -0600 Subject: HID: i2c-hid: Limit reads to wMaxInputLength bytes for input events d1c7e29e8d27 (HID: i2c-hid: prevent buffer overflow in early IRQ) changed hid_get_input() to read ihid->bufsize bytes, which can be more than wMaxInputLength. This is the case with the Dell XPS 13 9343, and it is causing events to be missed. In some cases the missed events are releases, which can cause the cursor to jump or freeze, among other problems. Limit the number of bytes read to min(wMaxInputLength, ihid->bufsize) to prevent such problems. Fixes: d1c7e29e8d27 "HID: i2c-hid: prevent buffer overflow in early IRQ" Signed-off-by: Seth Forshee Reviewed-by: Benjamin Tissoires Signed-off-by: Jiri Kosina --- drivers/hid/i2c-hid/i2c-hid.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/hid/i2c-hid/i2c-hid.c b/drivers/hid/i2c-hid/i2c-hid.c index 8f1dfc5c5d9c..36053f33d6d9 100644 --- a/drivers/hid/i2c-hid/i2c-hid.c +++ b/drivers/hid/i2c-hid/i2c-hid.c @@ -370,7 +370,10 @@ static int i2c_hid_hwreset(struct i2c_client *client) static void i2c_hid_get_input(struct i2c_hid *ihid) { int ret, ret_size; - int size = ihid->bufsize; + int size = le16_to_cpu(ihid->hdesc.wMaxInputLength); + + if (size > ihid->bufsize) + size = ihid->bufsize; ret = i2c_master_recv(ihid->client, ihid->inbuf, size); if (ret != size) { -- cgit v1.2.3-59-g8ed1b From ef567cf9ddb682dbfa840bf4a2600931299f9555 Mon Sep 17 00:00:00 2001 From: Jakub Sitnicki Date: Sat, 21 Feb 2015 20:51:08 +0100 Subject: HID: microsoft: Add ID for NE7K wireless keyboard Microsoft Natural Wireless Ergonomic Keyboard 7000 has special My Favorites 1..5 keys which are handled through a vendor-defined usage page (0xff05). Apply MS_ERGONOMY quirks handling to USB PID 0x071d (Microsoft Microsoft 2.4GHz Transceiver V1.0) so that the My Favorites 1..5 keys are reported as KEY_F14..18 events. Link: https://bugzilla.kernel.org/show_bug.cgi?id=52841 Signed-off-by: Jakub Sitnicki Signed-off-by: Jiri Kosina --- drivers/hid/hid-core.c | 1 + drivers/hid/hid-ids.h | 1 + drivers/hid/hid-microsoft.c | 2 ++ 3 files changed, 4 insertions(+) diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c index 40b27ea28deb..7c669c328c4c 100644 --- a/drivers/hid/hid-core.c +++ b/drivers/hid/hid-core.c @@ -1872,6 +1872,7 @@ static const struct hid_device_id hid_have_special_driver[] = { { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K_JP) }, + { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE7K) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_PRESENTER_8K_USB) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_DIGITAL_MEDIA_3K) }, diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h index b1ae48cdc0de..204312bfab2c 100644 --- a/drivers/hid/hid-ids.h +++ b/drivers/hid/hid-ids.h @@ -654,6 +654,7 @@ #define USB_DEVICE_ID_MS_LK6K 0x00f9 #define USB_DEVICE_ID_MS_PRESENTER_8K_BT 0x0701 #define USB_DEVICE_ID_MS_PRESENTER_8K_USB 0x0713 +#define USB_DEVICE_ID_MS_NE7K 0x071d #define USB_DEVICE_ID_MS_DIGITAL_MEDIA_3K 0x0730 #define USB_DEVICE_ID_MS_COMFORT_MOUSE_4500 0x076c #define USB_DEVICE_ID_MS_SURFACE_PRO_2 0x0799 diff --git a/drivers/hid/hid-microsoft.c b/drivers/hid/hid-microsoft.c index fbaea6eb882e..af935eb198c9 100644 --- a/drivers/hid/hid-microsoft.c +++ b/drivers/hid/hid-microsoft.c @@ -264,6 +264,8 @@ static const struct hid_device_id ms_devices[] = { .driver_data = MS_ERGONOMY }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K_JP), .driver_data = MS_ERGONOMY }, + { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE7K), + .driver_data = MS_ERGONOMY }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K), .driver_data = MS_ERGONOMY | MS_RDESC }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_PRESENTER_8K_USB), -- cgit v1.2.3-59-g8ed1b From 9cf75e9e4ddd587ac12e88e8751c358b7b27e95f Mon Sep 17 00:00:00 2001 From: Hans Holmberg Date: Tue, 10 Feb 2015 09:48:27 +0100 Subject: gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node The change: 7b8792bbdffdff3abda704f89c6a45ea97afdc62 gpiolib: of: Correct error handling in of_get_named_gpiod_flags assumed that only one gpio-chip is registred per of-node. Some drivers register more than one chip per of-node, so adjust the matching function of_gpiochip_find_and_xlate to not stop looking for chips if a node-match is found and the translation fails. Cc: Stable Fixes: 7b8792bbdffd ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags") Signed-off-by: Hans Holmberg Acked-by: Alexandre Courbot Tested-by: Robert Jarzmik Tested-by: Tyler Hall Signed-off-by: Linus Walleij --- drivers/gpio/gpiolib-of.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c index 8cad8e400b44..4650bf830d6b 100644 --- a/drivers/gpio/gpiolib-of.c +++ b/drivers/gpio/gpiolib-of.c @@ -46,12 +46,13 @@ static int of_gpiochip_find_and_xlate(struct gpio_chip *gc, void *data) ret = gc->of_xlate(gc, &gg_data->gpiospec, gg_data->flags); if (ret < 0) { - /* We've found the gpio chip, but the translation failed. - * Return true to stop looking and return the translation - * error via out_gpio + /* We've found a gpio chip, but the translation failed. + * Store translation error in out_gpio. + * Return false to keep looking, as more than one gpio chip + * could be registered per of-node. */ gg_data->out_gpio = ERR_PTR(ret); - return true; + return false; } gg_data->out_gpio = gpiochip_get_desc(gc, ret); -- cgit v1.2.3-59-g8ed1b From 2f97c20e5f7c3582c7310f65a04465bfb0fd0e85 Mon Sep 17 00:00:00 2001 From: Nicolas Saenz Julienne Date: Thu, 19 Feb 2015 01:52:25 +0000 Subject: gpio: tps65912: fix wrong container_of arguments The gpio_chip operations receive a pointer the gpio_chip struct which is contained in the driver's private struct, yet the container_of call in those functions point to the mfd struct defined in include/linux/mfd/tps65912.h. Cc: Stable Signed-off-by: Nicolas Saenz Julienne Signed-off-by: Linus Walleij --- drivers/gpio/gpio-tps65912.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) diff --git a/drivers/gpio/gpio-tps65912.c b/drivers/gpio/gpio-tps65912.c index 472fb5b8779f..9cdbc0c9cb2d 100644 --- a/drivers/gpio/gpio-tps65912.c +++ b/drivers/gpio/gpio-tps65912.c @@ -26,9 +26,12 @@ struct tps65912_gpio_data { struct gpio_chip gpio_chip; }; +#define to_tgd(gc) container_of(gc, struct tps65912_gpio_data, gpio_chip) + static int tps65912_gpio_get(struct gpio_chip *gc, unsigned offset) { - struct tps65912 *tps65912 = container_of(gc, struct tps65912, gpio); + struct tps65912_gpio_data *tps65912_gpio = to_tgd(gc); + struct tps65912 *tps65912 = tps65912_gpio->tps65912; int val; val = tps65912_reg_read(tps65912, TPS65912_GPIO1 + offset); @@ -42,7 +45,8 @@ static int tps65912_gpio_get(struct gpio_chip *gc, unsigned offset) static void tps65912_gpio_set(struct gpio_chip *gc, unsigned offset, int value) { - struct tps65912 *tps65912 = container_of(gc, struct tps65912, gpio); + struct tps65912_gpio_data *tps65912_gpio = to_tgd(gc); + struct tps65912 *tps65912 = tps65912_gpio->tps65912; if (value) tps65912_set_bits(tps65912, TPS65912_GPIO1 + offset, @@ -55,7 +59,8 @@ static void tps65912_gpio_set(struct gpio_chip *gc, unsigned offset, static int tps65912_gpio_output(struct gpio_chip *gc, unsigned offset, int value) { - struct tps65912 *tps65912 = container_of(gc, struct tps65912, gpio); + struct tps65912_gpio_data *tps65912_gpio = to_tgd(gc); + struct tps65912 *tps65912 = tps65912_gpio->tps65912; /* Set the initial value */ tps65912_gpio_set(gc, offset, value); @@ -66,7 +71,8 @@ static int tps65912_gpio_output(struct gpio_chip *gc, unsigned offset, static int tps65912_gpio_input(struct gpio_chip *gc, unsigned offset) { - struct tps65912 *tps65912 = container_of(gc, struct tps65912, gpio); + struct tps65912_gpio_data *tps65912_gpio = to_tgd(gc); + struct tps65912 *tps65912 = tps65912_gpio->tps65912; return tps65912_clear_bits(tps65912, TPS65912_GPIO1 + offset, GPIO_CFG_MASK); -- cgit v1.2.3-59-g8ed1b From 606bf4d5d630781c0e626b6811ac3aabb57fdf1b Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 4 Feb 2015 06:28:49 -0800 Subject: usb: musb: Fix use for of_property_read_bool for disabled multipoint The value for the multipoint dts property is ignored when parsing with of_property_read_bool, so we currently have multipoint always set as 1 even if value 0 is specified in the dts file. Let's fix this to read the value too instead of just the property like the binding documentation says as otherwise MUSB will fail to work on devices with Mentor configuration that does not support multipoint. Cc: Brian Hutchinson Signed-off-by: Tony Lindgren Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_dsps.c | 7 +++++-- drivers/usb/musb/omap2430.c | 7 +++++-- 2 files changed, 10 insertions(+), 4 deletions(-) diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c index 53bd0e71d19f..5872accb0fd3 100644 --- a/drivers/usb/musb/musb_dsps.c +++ b/drivers/usb/musb/musb_dsps.c @@ -687,7 +687,7 @@ static int dsps_create_musb_pdev(struct dsps_glue *glue, struct musb_hdrc_config *config; struct platform_device *musb; struct device_node *dn = parent->dev.of_node; - int ret; + int ret, val; memset(resources, 0, sizeof(resources)); res = platform_get_resource_byname(parent, IORESOURCE_MEM, "mc"); @@ -739,7 +739,10 @@ static int dsps_create_musb_pdev(struct dsps_glue *glue, pdata.mode = get_musb_port_mode(dev); /* DT keeps this entry in mA, musb expects it as per USB spec */ pdata.power = get_int_prop(dn, "mentor,power") / 2; - config->multipoint = of_property_read_bool(dn, "mentor,multipoint"); + + ret = of_property_read_u32(dn, "mentor,multipoint", &val); + if (!ret && val) + config->multipoint = true; ret = platform_device_add_data(musb, &pdata, sizeof(pdata)); if (ret) { diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c index 763649eb4987..cc752d8c7773 100644 --- a/drivers/usb/musb/omap2430.c +++ b/drivers/usb/musb/omap2430.c @@ -516,7 +516,7 @@ static int omap2430_probe(struct platform_device *pdev) struct omap2430_glue *glue; struct device_node *np = pdev->dev.of_node; struct musb_hdrc_config *config; - int ret = -ENOMEM; + int ret = -ENOMEM, val; glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL); if (!glue) @@ -559,7 +559,10 @@ static int omap2430_probe(struct platform_device *pdev) of_property_read_u32(np, "num-eps", (u32 *)&config->num_eps); of_property_read_u32(np, "ram-bits", (u32 *)&config->ram_bits); of_property_read_u32(np, "power", (u32 *)&pdata->power); - config->multipoint = of_property_read_bool(np, "multipoint"); + + ret = of_property_read_u32(np, "multipoint", &val); + if (!ret && val) + config->multipoint = true; pdata->board_data = data; pdata->config = config; -- cgit v1.2.3-59-g8ed1b From eed97ef39a30e3301c5a7f0c94db63130bbe785b Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 18 Feb 2015 22:07:07 +0100 Subject: usb: renesas: fix extcon dependency The renesas usbhs driver calls extcon_get_edev_by_phandle(), which is defined in drivers/extcon/extcon-class.c, and that can be a loadable module. If the extcon-class support is disabled, usbhs will work correctly for all devices that do not need extcon. However, if extcon-class is a loadable module, and usbhs is built-in, the kernel fails to link. In order to solve that, we need a Kconfig dependency that allows extcon to be disabled but does not allow usbhs built-in if extcon is a module. Signed-off-by: Arnd Bergmann Signed-off-by: Felipe Balbi --- drivers/usb/renesas_usbhs/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/renesas_usbhs/Kconfig b/drivers/usb/renesas_usbhs/Kconfig index de83b9d0cd5c..ebc99ee076ce 100644 --- a/drivers/usb/renesas_usbhs/Kconfig +++ b/drivers/usb/renesas_usbhs/Kconfig @@ -6,6 +6,7 @@ config USB_RENESAS_USBHS tristate 'Renesas USBHS controller' depends on USB_GADGET depends on ARCH_SHMOBILE || SUPERH || COMPILE_TEST + depends on EXTCON || !EXTCON # if EXTCON=m, USBHS cannot be built-in default n help Renesas USBHS is a discrete USB host and peripheral controller chip -- cgit v1.2.3-59-g8ed1b From bb90600d5cdd3a59053e0843f165e2ee49009c54 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 4 Feb 2015 06:28:49 -0800 Subject: usb: musb: Fix getting a generic phy for musb_dsps We still have a combination of legacy phys and generic phys in use so we need to support both types of phy for musb_dsps.c. Cc: Brian Hutchinson Signed-off-by: Tony Lindgren Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_dsps.c | 25 ++++++++++++++++++++++++- 1 file changed, 24 insertions(+), 1 deletion(-) diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c index 5872accb0fd3..a900c9877195 100644 --- a/drivers/usb/musb/musb_dsps.c +++ b/drivers/usb/musb/musb_dsps.c @@ -457,12 +457,27 @@ static int dsps_musb_init(struct musb *musb) if (IS_ERR(musb->xceiv)) return PTR_ERR(musb->xceiv); + musb->phy = devm_phy_get(dev->parent, "usb2-phy"); + /* Returns zero if e.g. not clocked */ rev = dsps_readl(reg_base, wrp->revision); if (!rev) return -ENODEV; usb_phy_init(musb->xceiv); + if (IS_ERR(musb->phy)) { + musb->phy = NULL; + } else { + ret = phy_init(musb->phy); + if (ret < 0) + return ret; + ret = phy_power_on(musb->phy); + if (ret) { + phy_exit(musb->phy); + return ret; + } + } + setup_timer(&glue->timer, otg_timer, (unsigned long) musb); /* Reset the musb */ @@ -502,6 +517,8 @@ static int dsps_musb_exit(struct musb *musb) del_timer_sync(&glue->timer); usb_phy_shutdown(musb->xceiv); + phy_power_off(musb->phy); + phy_exit(musb->phy); debugfs_remove_recursive(glue->dbgfs_root); return 0; @@ -610,7 +627,7 @@ static int dsps_musb_reset(struct musb *musb) struct device *dev = musb->controller; struct dsps_glue *glue = dev_get_drvdata(dev->parent); const struct dsps_musb_wrapper *wrp = glue->wrp; - int session_restart = 0; + int session_restart = 0, error; if (glue->sw_babble_enabled) session_restart = sw_babble_control(musb); @@ -624,8 +641,14 @@ static int dsps_musb_reset(struct musb *musb) dsps_writel(musb->ctrl_base, wrp->control, (1 << wrp->reset)); usleep_range(100, 200); usb_phy_shutdown(musb->xceiv); + error = phy_power_off(musb->phy); + if (error) + dev_err(dev, "phy shutdown failed: %i\n", error); usleep_range(100, 200); usb_phy_init(musb->xceiv); + error = phy_power_on(musb->phy); + if (error) + dev_err(dev, "phy powerup failed: %i\n", error); session_restart = 1; } -- cgit v1.2.3-59-g8ed1b From 4d3db7d78425c469d328d460e3b69dfb80dd309c Mon Sep 17 00:00:00 2001 From: Nicholas Mc Guire Date: Fri, 6 Feb 2015 05:08:53 -0500 Subject: usb: isp1760: use msecs_to_jiffies for time conversion This is only an API consolidation and should make things more readable it replaces var * HZ / 1000 by msecs_to_jiffies(var). Acked-by: Laurent Pinchart Signed-off-by: Nicholas Mc Guire Signed-off-by: Felipe Balbi --- drivers/usb/isp1760/isp1760-hcd.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/usb/isp1760/isp1760-hcd.c b/drivers/usb/isp1760/isp1760-hcd.c index eba9b82e2d70..3cb98b1d5d29 100644 --- a/drivers/usb/isp1760/isp1760-hcd.c +++ b/drivers/usb/isp1760/isp1760-hcd.c @@ -1274,7 +1274,7 @@ static void errata2_function(unsigned long data) for (slot = 0; slot < 32; slot++) if (priv->atl_slots[slot].qh && time_after(jiffies, priv->atl_slots[slot].timestamp + - SLOT_TIMEOUT * HZ / 1000)) { + msecs_to_jiffies(SLOT_TIMEOUT))) { ptd_read(hcd->regs, ATL_PTD_OFFSET, slot, &ptd); if (!FROM_DW0_VALID(ptd.dw0) && !FROM_DW3_ACTIVE(ptd.dw3)) @@ -1286,7 +1286,7 @@ static void errata2_function(unsigned long data) spin_unlock_irqrestore(&priv->lock, spinflags); - errata2_timer.expires = jiffies + SLOT_CHECK_PERIOD * HZ / 1000; + errata2_timer.expires = jiffies + msecs_to_jiffies(SLOT_CHECK_PERIOD); add_timer(&errata2_timer); } @@ -1336,7 +1336,7 @@ static int isp1760_run(struct usb_hcd *hcd) return retval; setup_timer(&errata2_timer, errata2_function, (unsigned long)hcd); - errata2_timer.expires = jiffies + SLOT_CHECK_PERIOD * HZ / 1000; + errata2_timer.expires = jiffies + msecs_to_jiffies(SLOT_CHECK_PERIOD); add_timer(&errata2_timer); chipid = reg_read32(hcd->regs, HC_CHIP_ID_REG); -- cgit v1.2.3-59-g8ed1b From 7a3cc4618497e1c6b2f9cd4c8c20759ad8ceb2d1 Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Wed, 4 Feb 2015 17:49:36 +0000 Subject: usb: gadget: function: f_hid: fix sparse warning this patch fixes following sparse warning: f_hid.c:572:30: warning: symbol 'f_hidg_fops' was not declared. Should it be static? Signed-off-by: Lad, Prabhakar Signed-off-by: Felipe Balbi --- drivers/usb/gadget/function/f_hid.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/gadget/function/f_hid.c b/drivers/usb/gadget/function/f_hid.c index 426d69a9c018..a2612fb79eff 100644 --- a/drivers/usb/gadget/function/f_hid.c +++ b/drivers/usb/gadget/function/f_hid.c @@ -569,7 +569,7 @@ fail: return status; } -const struct file_operations f_hidg_fops = { +static const struct file_operations f_hidg_fops = { .owner = THIS_MODULE, .open = f_hidg_open, .release = f_hidg_release, -- cgit v1.2.3-59-g8ed1b From ef16e7c8ba9cee07d2295de01bbdf921d20c4902 Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Wed, 4 Feb 2015 18:01:11 +0000 Subject: usb: gadget: function: f_uac2: fix sparse warnings this patch fixes following sparse warnings: f_uac2.c:57:12: warning: symbol 'uac2_name' was not declared. Should it be static? f_uac2.c:637:36: warning: symbol 'in_clk_src_desc' was not declared. Should it be static? f_uac2.c:649:36: warning: symbol 'out_clk_src_desc' was not declared. Should it be static? f_uac2.c:661:39: warning: symbol 'usb_out_it_desc' was not declared. Should it be static? f_uac2.c:675:39: warning: symbol 'io_in_it_desc' was not declared. Should it be static? f_uac2.c:689:40: warning: symbol 'usb_in_ot_desc' was not declared. Should it be static? f_uac2.c:703:40: warning: symbol 'io_out_ot_desc' was not declared. Should it be static? f_uac2.c:716:34: warning: symbol 'ac_hdr_desc' was not declared. Should it be static? f_uac2.c:754:34: warning: symbol 'as_out_hdr_desc' was not declared. Should it be static? f_uac2.c:767:38: warning: symbol 'as_out_fmt1_desc' was not declared. Should it be static? f_uac2.c:775:32: warning: symbol 'fs_epout_desc' was not declared. Should it be static? f_uac2.c:785:32: warning: symbol 'hs_epout_desc' was not declared. Should it be static? f_uac2.c:831:34: warning: symbol 'as_in_hdr_desc' was not declared. Should it be static? f_uac2.c:844:38: warning: symbol 'as_in_fmt1_desc' was not declared. Should it be static? f_uac2.c:852:32: warning: symbol 'fs_epin_desc' was not declared. Should it be static? f_uac2.c:862:32: warning: symbol 'hs_epin_desc' was not declared. Should it be static? f_uac2.c:1566:21: warning: symbol 'afunc_alloc' was not declared. Should it be static? Signed-off-by: Lad, Prabhakar Signed-off-by: Felipe Balbi --- drivers/usb/gadget/function/f_uac2.c | 34 +++++++++++++++++----------------- 1 file changed, 17 insertions(+), 17 deletions(-) diff --git a/drivers/usb/gadget/function/f_uac2.c b/drivers/usb/gadget/function/f_uac2.c index 33e16658e5cf..6d3eb8b00a48 100644 --- a/drivers/usb/gadget/function/f_uac2.c +++ b/drivers/usb/gadget/function/f_uac2.c @@ -54,7 +54,7 @@ #define UNFLW_CTRL 8 #define OVFLW_CTRL 10 -const char *uac2_name = "snd_uac2"; +static const char *uac2_name = "snd_uac2"; struct uac2_req { struct uac2_rtd_params *pp; /* parent param */ @@ -634,7 +634,7 @@ static struct usb_interface_descriptor std_ac_if_desc = { }; /* Clock source for IN traffic */ -struct uac_clock_source_descriptor in_clk_src_desc = { +static struct uac_clock_source_descriptor in_clk_src_desc = { .bLength = sizeof in_clk_src_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -646,7 +646,7 @@ struct uac_clock_source_descriptor in_clk_src_desc = { }; /* Clock source for OUT traffic */ -struct uac_clock_source_descriptor out_clk_src_desc = { +static struct uac_clock_source_descriptor out_clk_src_desc = { .bLength = sizeof out_clk_src_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -658,7 +658,7 @@ struct uac_clock_source_descriptor out_clk_src_desc = { }; /* Input Terminal for USB_OUT */ -struct uac2_input_terminal_descriptor usb_out_it_desc = { +static struct uac2_input_terminal_descriptor usb_out_it_desc = { .bLength = sizeof usb_out_it_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -672,7 +672,7 @@ struct uac2_input_terminal_descriptor usb_out_it_desc = { }; /* Input Terminal for I/O-In */ -struct uac2_input_terminal_descriptor io_in_it_desc = { +static struct uac2_input_terminal_descriptor io_in_it_desc = { .bLength = sizeof io_in_it_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -686,7 +686,7 @@ struct uac2_input_terminal_descriptor io_in_it_desc = { }; /* Ouput Terminal for USB_IN */ -struct uac2_output_terminal_descriptor usb_in_ot_desc = { +static struct uac2_output_terminal_descriptor usb_in_ot_desc = { .bLength = sizeof usb_in_ot_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -700,7 +700,7 @@ struct uac2_output_terminal_descriptor usb_in_ot_desc = { }; /* Ouput Terminal for I/O-Out */ -struct uac2_output_terminal_descriptor io_out_ot_desc = { +static struct uac2_output_terminal_descriptor io_out_ot_desc = { .bLength = sizeof io_out_ot_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -713,7 +713,7 @@ struct uac2_output_terminal_descriptor io_out_ot_desc = { .bmControls = (CONTROL_RDWR << COPY_CTRL), }; -struct uac2_ac_header_descriptor ac_hdr_desc = { +static struct uac2_ac_header_descriptor ac_hdr_desc = { .bLength = sizeof ac_hdr_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -751,7 +751,7 @@ static struct usb_interface_descriptor std_as_out_if1_desc = { }; /* Audio Stream OUT Intface Desc */ -struct uac2_as_header_descriptor as_out_hdr_desc = { +static struct uac2_as_header_descriptor as_out_hdr_desc = { .bLength = sizeof as_out_hdr_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -764,7 +764,7 @@ struct uac2_as_header_descriptor as_out_hdr_desc = { }; /* Audio USB_OUT Format */ -struct uac2_format_type_i_descriptor as_out_fmt1_desc = { +static struct uac2_format_type_i_descriptor as_out_fmt1_desc = { .bLength = sizeof as_out_fmt1_desc, .bDescriptorType = USB_DT_CS_INTERFACE, .bDescriptorSubtype = UAC_FORMAT_TYPE, @@ -772,7 +772,7 @@ struct uac2_format_type_i_descriptor as_out_fmt1_desc = { }; /* STD AS ISO OUT Endpoint */ -struct usb_endpoint_descriptor fs_epout_desc = { +static struct usb_endpoint_descriptor fs_epout_desc = { .bLength = USB_DT_ENDPOINT_SIZE, .bDescriptorType = USB_DT_ENDPOINT, @@ -782,7 +782,7 @@ struct usb_endpoint_descriptor fs_epout_desc = { .bInterval = 1, }; -struct usb_endpoint_descriptor hs_epout_desc = { +static struct usb_endpoint_descriptor hs_epout_desc = { .bLength = USB_DT_ENDPOINT_SIZE, .bDescriptorType = USB_DT_ENDPOINT, @@ -828,7 +828,7 @@ static struct usb_interface_descriptor std_as_in_if1_desc = { }; /* Audio Stream IN Intface Desc */ -struct uac2_as_header_descriptor as_in_hdr_desc = { +static struct uac2_as_header_descriptor as_in_hdr_desc = { .bLength = sizeof as_in_hdr_desc, .bDescriptorType = USB_DT_CS_INTERFACE, @@ -841,7 +841,7 @@ struct uac2_as_header_descriptor as_in_hdr_desc = { }; /* Audio USB_IN Format */ -struct uac2_format_type_i_descriptor as_in_fmt1_desc = { +static struct uac2_format_type_i_descriptor as_in_fmt1_desc = { .bLength = sizeof as_in_fmt1_desc, .bDescriptorType = USB_DT_CS_INTERFACE, .bDescriptorSubtype = UAC_FORMAT_TYPE, @@ -849,7 +849,7 @@ struct uac2_format_type_i_descriptor as_in_fmt1_desc = { }; /* STD AS ISO IN Endpoint */ -struct usb_endpoint_descriptor fs_epin_desc = { +static struct usb_endpoint_descriptor fs_epin_desc = { .bLength = USB_DT_ENDPOINT_SIZE, .bDescriptorType = USB_DT_ENDPOINT, @@ -859,7 +859,7 @@ struct usb_endpoint_descriptor fs_epin_desc = { .bInterval = 1, }; -struct usb_endpoint_descriptor hs_epin_desc = { +static struct usb_endpoint_descriptor hs_epin_desc = { .bLength = USB_DT_ENDPOINT_SIZE, .bDescriptorType = USB_DT_ENDPOINT, @@ -1563,7 +1563,7 @@ static void afunc_unbind(struct usb_configuration *c, struct usb_function *f) agdev->out_ep->driver_data = NULL; } -struct usb_function *afunc_alloc(struct usb_function_instance *fi) +static struct usb_function *afunc_alloc(struct usb_function_instance *fi) { struct audio_dev *agdev; struct f_uac2_opts *opts; -- cgit v1.2.3-59-g8ed1b From fcaddc5d7efbee24a6e324672a7f4118c2686648 Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Wed, 4 Feb 2015 18:09:59 +0000 Subject: usb: gadget: function: f_sourcesink: fix sparse warning this patch fixes following sparse warnings: f_sourcesink.c:347:34: warning: symbol 'ss_int_source_comp_desc' was not declared. Should it be static? f_sourcesink.c:365:34: warning: symbol 'ss_int_sink_comp_desc' was not declared. Should it be static? Signed-off-by: Lad, Prabhakar Signed-off-by: Felipe Balbi --- drivers/usb/gadget/function/f_sourcesink.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/gadget/function/f_sourcesink.c b/drivers/usb/gadget/function/f_sourcesink.c index e07c50ced64d..e3dae47baef3 100644 --- a/drivers/usb/gadget/function/f_sourcesink.c +++ b/drivers/usb/gadget/function/f_sourcesink.c @@ -344,7 +344,7 @@ static struct usb_endpoint_descriptor ss_int_source_desc = { .bInterval = USB_MS_TO_SS_INTERVAL(GZERO_INT_INTERVAL), }; -struct usb_ss_ep_comp_descriptor ss_int_source_comp_desc = { +static struct usb_ss_ep_comp_descriptor ss_int_source_comp_desc = { .bLength = USB_DT_SS_EP_COMP_SIZE, .bDescriptorType = USB_DT_SS_ENDPOINT_COMP, @@ -362,7 +362,7 @@ static struct usb_endpoint_descriptor ss_int_sink_desc = { .bInterval = USB_MS_TO_SS_INTERVAL(GZERO_INT_INTERVAL), }; -struct usb_ss_ep_comp_descriptor ss_int_sink_comp_desc = { +static struct usb_ss_ep_comp_descriptor ss_int_sink_comp_desc = { .bLength = USB_DT_SS_EP_COMP_SIZE, .bDescriptorType = USB_DT_SS_ENDPOINT_COMP, -- cgit v1.2.3-59-g8ed1b From 70685711f2fead61817785169587b8914df416bf Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Thu, 5 Feb 2015 13:02:18 +0000 Subject: usb: gadget: function: uvc: fix sparse warnings this patch fixes following sparse warnings: uvc_video.c:283:5: warning: symbol 'uvcg_video_pump' was not declared. Should it be static? uvc_video.c:342:5: warning: symbol 'uvcg_video_enable' was not declared. Should it be static? uvc_video.c:381:5: warning: symbol 'uvcg_video_init' was not declared. Should it be static? Signed-off-by: Lad, Prabhakar Signed-off-by: Felipe Balbi --- drivers/usb/gadget/function/uvc_video.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/gadget/function/uvc_video.c b/drivers/usb/gadget/function/uvc_video.c index 9cb86bc1a9a5..50a5e637ca35 100644 --- a/drivers/usb/gadget/function/uvc_video.c +++ b/drivers/usb/gadget/function/uvc_video.c @@ -21,6 +21,7 @@ #include "uvc.h" #include "uvc_queue.h" +#include "uvc_video.h" /* -------------------------------------------------------------------------- * Video codecs -- cgit v1.2.3-59-g8ed1b From 2b87cd24c3451608d728862d4d62ff27f2d82e93 Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Thu, 5 Feb 2015 13:11:47 +0000 Subject: usb: gadget: gadgetfs: fix sparse warnings this patch fixes following sparse warnings: g_ffs.c:136:3: warning: symbol 'gfs_configurations' was not declared. Should it be static? g_ffs.c:281:16: warning: Using plain integer as NULL pointer Signed-off-by: Lad, Prabhakar Signed-off-by: Felipe Balbi --- drivers/usb/gadget/legacy/g_ffs.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/usb/gadget/legacy/g_ffs.c b/drivers/usb/gadget/legacy/g_ffs.c index 06acfa55864a..b01b88e1b716 100644 --- a/drivers/usb/gadget/legacy/g_ffs.c +++ b/drivers/usb/gadget/legacy/g_ffs.c @@ -133,7 +133,9 @@ struct gfs_configuration { struct usb_configuration c; int (*eth)(struct usb_configuration *c); int num; -} gfs_configurations[] = { +}; + +static struct gfs_configuration gfs_configurations[] = { #ifdef CONFIG_USB_FUNCTIONFS_RNDIS { .eth = bind_rndis_config, @@ -278,7 +280,7 @@ static void *functionfs_acquire_dev(struct ffs_dev *dev) if (!try_module_get(THIS_MODULE)) return ERR_PTR(-ENOENT); - return 0; + return NULL; } static void functionfs_release_dev(struct ffs_dev *dev) -- cgit v1.2.3-59-g8ed1b From 1f754ef10350681f3dc1980d357e77487d308c52 Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Thu, 5 Feb 2015 13:16:26 +0000 Subject: usb: gadget: function: uvc_v4l2.c: fix sparse warnings this patch fixes following sparse warnings: uvc_v4l2.c:264:29: warning: symbol 'uvc_v4l2_ioctl_ops' was not declared. Should it be static? uvc_v4l2.c:355:29: warning: symbol 'uvc_v4l2_fops' was not declared. Should it be static? Acked-by: Laurent Pinchart Signed-off-by: Lad, Prabhakar Signed-off-by: Felipe Balbi --- drivers/usb/gadget/function/uvc_v4l2.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/gadget/function/uvc_v4l2.c b/drivers/usb/gadget/function/uvc_v4l2.c index 5aad7fededa5..8b818fd027b3 100644 --- a/drivers/usb/gadget/function/uvc_v4l2.c +++ b/drivers/usb/gadget/function/uvc_v4l2.c @@ -27,6 +27,7 @@ #include "uvc.h" #include "uvc_queue.h" #include "uvc_video.h" +#include "uvc_v4l2.h" /* -------------------------------------------------------------------------- * Requests handling -- cgit v1.2.3-59-g8ed1b From 96e5d31244c5542f5b2ea81d76f14ba4b8a7d440 Mon Sep 17 00:00:00 2001 From: George Cherian Date: Fri, 13 Feb 2015 10:13:24 +0530 Subject: usb: dwc3: dwc3-omap: Fix disable IRQ In the wrapper the IRQ disable should be done by writing 1's to the IRQ*_CLR register. Existing code is broken because it instead writes zeros to IRQ*_SET register. Fix this by adding functions dwc3_omap_write_irqmisc_clr() and dwc3_omap_write_irq0_clr() which do the right thing. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: # v3.2+ Signed-off-by: George Cherian Signed-off-by: Felipe Balbi --- drivers/usb/dwc3/dwc3-omap.c | 30 ++++++++++++++++++++++++++++-- 1 file changed, 28 insertions(+), 2 deletions(-) diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c index 172d64e585b6..52e0c4e5e48e 100644 --- a/drivers/usb/dwc3/dwc3-omap.c +++ b/drivers/usb/dwc3/dwc3-omap.c @@ -205,6 +205,18 @@ static void dwc3_omap_write_irq0_set(struct dwc3_omap *omap, u32 value) omap->irq0_offset, value); } +static void dwc3_omap_write_irqmisc_clr(struct dwc3_omap *omap, u32 value) +{ + dwc3_omap_writel(omap->base, USBOTGSS_IRQENABLE_CLR_MISC + + omap->irqmisc_offset, value); +} + +static void dwc3_omap_write_irq0_clr(struct dwc3_omap *omap, u32 value) +{ + dwc3_omap_writel(omap->base, USBOTGSS_IRQENABLE_CLR_0 - + omap->irq0_offset, value); +} + static void dwc3_omap_set_mailbox(struct dwc3_omap *omap, enum omap_dwc3_vbus_id_status status) { @@ -345,9 +357,23 @@ static void dwc3_omap_enable_irqs(struct dwc3_omap *omap) static void dwc3_omap_disable_irqs(struct dwc3_omap *omap) { + u32 reg; + /* disable all IRQs */ - dwc3_omap_write_irqmisc_set(omap, 0x00); - dwc3_omap_write_irq0_set(omap, 0x00); + reg = USBOTGSS_IRQO_COREIRQ_ST; + dwc3_omap_write_irq0_clr(omap, reg); + + reg = (USBOTGSS_IRQMISC_OEVT | + USBOTGSS_IRQMISC_DRVVBUS_RISE | + USBOTGSS_IRQMISC_CHRGVBUS_RISE | + USBOTGSS_IRQMISC_DISCHRGVBUS_RISE | + USBOTGSS_IRQMISC_IDPULLUP_RISE | + USBOTGSS_IRQMISC_DRVVBUS_FALL | + USBOTGSS_IRQMISC_CHRGVBUS_FALL | + USBOTGSS_IRQMISC_DISCHRGVBUS_FALL | + USBOTGSS_IRQMISC_IDPULLUP_FALL); + + dwc3_omap_write_irqmisc_clr(omap, reg); } static u64 dwc3_omap_dma_mask = DMA_BIT_MASK(32); -- cgit v1.2.3-59-g8ed1b From a0456399fb07155637a2b597b91cc1c63bc25141 Mon Sep 17 00:00:00 2001 From: Andrzej Pietrasiewicz Date: Fri, 13 Feb 2015 12:12:53 +0100 Subject: usb: gadget: configfs: don't NUL-terminate (sub)compatible ids The "Extended Compat ID OS Feature Descriptor Specification" does not require the (sub)compatible ids to be NUL-terminated, because they are placed in a fixed-size buffer and only unused parts of it should contain NULs. If the buffer is fully utilized, there is no place for NULs. Consequently, the code which uses desc->ext_compat_id never expects the data contained to be NUL terminated. If the compatible id is stored after sub-compatible id, and the compatible id is full length (8 bytes), the (useless) NUL terminator overwrites the first byte of the sub-compatible id. If the sub-compatible id is full length (8 bytes), the (useless) NUL terminator ends up out of the buffer. The situation can happen in the RNDIS function, where the buffer is a part of struct f_rndis_opts. The next member of struct f_rndis_opts is a mutex, so its first byte gets overwritten. The said byte is a part of a mutex'es member which contains the information on whether the muext is locked or not. This can lead to a deadlock, because, in a configfs-composed gadget when a function is linked into a configuration with config_usb_cfg_link(), usb_get_function() is called, which then calls rndis_alloc(), which tries locking the same mutex and (wrongly) finds it already locked. This patch eliminates NUL terminating of the (sub)compatible id. Cc: # v3.16+ Fixes: da4243145fb1: "usb: gadget: configfs: OS Extended Compatibility descriptors support" Reported-by: Dan Carpenter Signed-off-by: Andrzej Pietrasiewicz Signed-off-by: Felipe Balbi --- drivers/usb/gadget/configfs.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/usb/gadget/configfs.c b/drivers/usb/gadget/configfs.c index 75648145dc1b..c42765b3a060 100644 --- a/drivers/usb/gadget/configfs.c +++ b/drivers/usb/gadget/configfs.c @@ -1161,7 +1161,6 @@ static ssize_t interf_grp_compatible_id_store(struct usb_os_desc *desc, if (desc->opts_mutex) mutex_lock(desc->opts_mutex); memcpy(desc->ext_compat_id, page, l); - desc->ext_compat_id[l] = '\0'; if (desc->opts_mutex) mutex_unlock(desc->opts_mutex); @@ -1192,7 +1191,6 @@ static ssize_t interf_grp_sub_compatible_id_store(struct usb_os_desc *desc, if (desc->opts_mutex) mutex_lock(desc->opts_mutex); memcpy(desc->ext_compat_id + 8, page, l); - desc->ext_compat_id[l + 8] = '\0'; if (desc->opts_mutex) mutex_unlock(desc->opts_mutex); -- cgit v1.2.3-59-g8ed1b From b3ec1c35385a16ddd98fdf104dcf4623a66e042a Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Thu, 12 Feb 2015 09:59:55 +0530 Subject: ASoC: Intel: update MMX ID to 3 The updated firmware expects the MMX ID to be used as 3, so update the driver as well Signed-off-by: Vinod Koul Signed-off-by: Mark Brown --- sound/soc/intel/sst-atom-controls.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/intel/sst-atom-controls.h b/sound/soc/intel/sst-atom-controls.h index dfebfdd5eb2a..daecc58f28af 100644 --- a/sound/soc/intel/sst-atom-controls.h +++ b/sound/soc/intel/sst-atom-controls.h @@ -150,7 +150,7 @@ enum sst_cmd_type { enum sst_task { SST_TASK_SBA = 1, - SST_TASK_MMX, + SST_TASK_MMX = 3, }; enum sst_type { -- cgit v1.2.3-59-g8ed1b From a825ac7678a43f7a22ff19842baebcf4aa14e950 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Thu, 12 Feb 2015 09:59:59 +0530 Subject: ASoC: Intel: save and restore the CSR register The IPC driver saved only IMR register, we need to save the CSR as well, so add it Signed-off-by: Vinod Koul Signed-off-by: Mark Brown --- sound/soc/intel/sst/sst.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/sound/soc/intel/sst/sst.c b/sound/soc/intel/sst/sst.c index d6ea80076ea2..97234ec4e416 100644 --- a/sound/soc/intel/sst/sst.c +++ b/sound/soc/intel/sst/sst.c @@ -350,7 +350,9 @@ static inline void sst_save_shim64(struct intel_sst_drv *ctx, spin_lock_irqsave(&ctx->ipc_spin_lock, irq_flags); - shim_regs->imrx = sst_shim_read64(shim, SST_IMRX), + shim_regs->imrx = sst_shim_read64(shim, SST_IMRX); + shim_regs->csr = sst_shim_read64(shim, SST_CSR); + spin_unlock_irqrestore(&ctx->ipc_spin_lock, irq_flags); } @@ -367,6 +369,7 @@ static inline void sst_restore_shim64(struct intel_sst_drv *ctx, */ spin_lock_irqsave(&ctx->ipc_spin_lock, irq_flags); sst_shim_write64(shim, SST_IMRX, shim_regs->imrx), + sst_shim_write64(shim, SST_CSR, shim_regs->csr), spin_unlock_irqrestore(&ctx->ipc_spin_lock, irq_flags); } -- cgit v1.2.3-59-g8ed1b From de251d773bb214fa5e7666a0da1225528e07da5e Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Thu, 12 Feb 2015 10:00:00 +0530 Subject: ASoC: Intel: reset the DSP while suspending The manual recommends that we reset the DSP when we suspend so add that in runtime suspend handler Signed-off-by: Vinod Koul Signed-off-by: Mark Brown --- sound/soc/intel/sst/sst.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/intel/sst/sst.c b/sound/soc/intel/sst/sst.c index 97234ec4e416..11c578651c1c 100644 --- a/sound/soc/intel/sst/sst.c +++ b/sound/soc/intel/sst/sst.c @@ -416,6 +416,7 @@ static int intel_sst_runtime_suspend(struct device *dev) synchronize_irq(ctx->irq_num); flush_workqueue(ctx->post_msg_wq); + ctx->ops->reset(ctx); /* save the shim registers because PMC doesn't save state */ sst_save_shim64(ctx, ctx->shim, ctx->shim_regs64); -- cgit v1.2.3-59-g8ed1b From 70372a7566b5e552dbe48abdac08c275081d8558 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 18 Dec 2014 10:02:41 +0100 Subject: ALSA: pcm: Don't leave PREPARED state after draining When a PCM draining is performed to an empty stream that has been already in PREPARED state, the current code just ignores and leaves as it is, although the drain is supposed to set all such streams to SETUP state. This patch covers that overlooked case. Cc: Signed-off-by: Takashi Iwai --- sound/core/pcm_native.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/sound/core/pcm_native.c b/sound/core/pcm_native.c index b03a638b420c..279e24f61305 100644 --- a/sound/core/pcm_native.c +++ b/sound/core/pcm_native.c @@ -1552,6 +1552,8 @@ static int snd_pcm_do_drain_init(struct snd_pcm_substream *substream, int state) if (! snd_pcm_playback_empty(substream)) { snd_pcm_do_start(substream, SNDRV_PCM_STATE_DRAINING); snd_pcm_post_start(substream, SNDRV_PCM_STATE_DRAINING); + } else { + runtime->status->state = SNDRV_PCM_STATE_SETUP; } break; case SNDRV_PCM_STATE_RUNNING: -- cgit v1.2.3-59-g8ed1b From 89ce4b0f4e7adda75ac7eec6aaa9b3516390cef2 Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Thu, 8 Jan 2015 00:04:04 +0100 Subject: gpu: ipu-v3: do not divide by zero if the pixel clock is too large Even if an unsupported mode with a pixel clock larger than two times the 264 MHz IPU HSP clock is set, don't divide by zero. Signed-off-by: Philipp Zabel --- drivers/gpu/ipu-v3/ipu-di.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/gpu/ipu-v3/ipu-di.c b/drivers/gpu/ipu-v3/ipu-di.c index b61d6be97602..3ddfb3d0b64d 100644 --- a/drivers/gpu/ipu-v3/ipu-di.c +++ b/drivers/gpu/ipu-v3/ipu-di.c @@ -459,6 +459,8 @@ static void ipu_di_config_clock(struct ipu_di *di, clkrate = clk_get_rate(di->clk_ipu); div = DIV_ROUND_CLOSEST(clkrate, sig->mode.pixelclock); + if (div == 0) + div = 1; rate = clkrate / div; error = rate / (sig->mode.pixelclock / 1000); -- cgit v1.2.3-59-g8ed1b From 081c80e85feabe9a0081f4db940fccb6443b81fb Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Wed, 7 Jan 2015 23:52:15 +0100 Subject: drm/imx: dw_hdmi-imx: add mode_valid callback prune unsupported modes This patch limits the pixel clock to 13.4 MHz - 266 MHz for i.MX6Q and 13.5 MHz - 270 MHz for i.MX6DL, which is the range documented in the HDMI Transmitter chapter of the respective reference manuals. Without this patch, when connected to a monitor capable of 2160p60 modes, dw_hdmi will happily report this mode and the IPU code will cause a division by zero in ipu_di_config_clock when trying to figure out how to divide the 264 MHz HSP clock down to ~600 MHz. Signed-off-by: Philipp Zabel --- drivers/gpu/drm/imx/dw_hdmi-imx.c | 32 ++++++++++++++++++++++++++++---- 1 file changed, 28 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/imx/dw_hdmi-imx.c b/drivers/gpu/drm/imx/dw_hdmi-imx.c index 121d30ca2d44..d25aaef3cba6 100644 --- a/drivers/gpu/drm/imx/dw_hdmi-imx.c +++ b/drivers/gpu/drm/imx/dw_hdmi-imx.c @@ -136,11 +136,34 @@ static struct drm_encoder_funcs dw_hdmi_imx_encoder_funcs = { .destroy = drm_encoder_cleanup, }; +static enum drm_mode_status imx6q_hdmi_mode_valid(struct drm_connector *con, + struct drm_display_mode *mode) +{ + if (mode->clock < 13500) + return MODE_CLOCK_LOW; + if (mode->clock > 266000) + return MODE_CLOCK_HIGH; + + return MODE_OK; +} + +static enum drm_mode_status imx6dl_hdmi_mode_valid(struct drm_connector *con, + struct drm_display_mode *mode) +{ + if (mode->clock < 13500) + return MODE_CLOCK_LOW; + if (mode->clock > 270000) + return MODE_CLOCK_HIGH; + + return MODE_OK; +} + static struct dw_hdmi_plat_data imx6q_hdmi_drv_data = { - .mpll_cfg = imx_mpll_cfg, - .cur_ctr = imx_cur_ctr, - .sym_term = imx_sym_term, - .dev_type = IMX6Q_HDMI, + .mpll_cfg = imx_mpll_cfg, + .cur_ctr = imx_cur_ctr, + .sym_term = imx_sym_term, + .dev_type = IMX6Q_HDMI, + .mode_valid = imx6q_hdmi_mode_valid, }; static struct dw_hdmi_plat_data imx6dl_hdmi_drv_data = { @@ -148,6 +171,7 @@ static struct dw_hdmi_plat_data imx6dl_hdmi_drv_data = { .cur_ctr = imx_cur_ctr, .sym_term = imx_sym_term, .dev_type = IMX6DL_HDMI, + .mode_valid = imx6dl_hdmi_mode_valid, }; static const struct of_device_id dw_hdmi_imx_dt_ids[] = { -- cgit v1.2.3-59-g8ed1b From 6e8958ec0ecfd83691e6854839f917d3eaca236b Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Wed, 7 Jan 2015 23:49:41 +0100 Subject: drm/imx: dw_hdmi-imx: add end of array element to current control array The loop iterating over curr_ctrl in dw_hdmi terminates on mpixelclock == ~0UL, so there needs to be an end of list element here in case a mode with a pixel clock larger than 216 MHz is set. Signed-off-by: Philipp Zabel --- drivers/gpu/drm/imx/dw_hdmi-imx.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/imx/dw_hdmi-imx.c b/drivers/gpu/drm/imx/dw_hdmi-imx.c index d25aaef3cba6..87fe8ed92ebe 100644 --- a/drivers/gpu/drm/imx/dw_hdmi-imx.c +++ b/drivers/gpu/drm/imx/dw_hdmi-imx.c @@ -70,7 +70,9 @@ static const struct dw_hdmi_curr_ctrl imx_cur_ctr[] = { 118800000, { 0x091c, 0x091c, 0x06dc }, }, { 216000000, { 0x06dc, 0x0b5c, 0x091c }, - } + }, { + ~0UL, { 0x0000, 0x0000, 0x0000 }, + }, }; static const struct dw_hdmi_sym_term imx_sym_term[] = { -- cgit v1.2.3-59-g8ed1b From 51dac94e801fb779789fa8e38bac7df306ac4fa7 Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Fri, 23 Jan 2015 17:10:01 +0100 Subject: drm/imx: imx-ldb: enable DI clock in encoder_mode_set Commit eb10d6355532 ("imx-drm: encoder prepare/mode_set must use adjusted mode") broke the first LVDS modeset by using crtc->hwmode before crtc mode_set is called. In fact, encoder prepare is not supposed to prepare the display clock at all. Rather encoder mode_set should be used to set the DI clock rate, before it is enabled by crtc commit. Reported-by: Liu Ying Tested-by: Fabio Estevam Signed-off-by: Philipp Zabel --- drivers/gpu/drm/imx/imx-ldb.c | 28 +++++++++++++--------------- 1 file changed, 13 insertions(+), 15 deletions(-) diff --git a/drivers/gpu/drm/imx/imx-ldb.c b/drivers/gpu/drm/imx/imx-ldb.c index 1b86aac0b341..2d6dc94e1e64 100644 --- a/drivers/gpu/drm/imx/imx-ldb.c +++ b/drivers/gpu/drm/imx/imx-ldb.c @@ -163,22 +163,7 @@ static void imx_ldb_encoder_prepare(struct drm_encoder *encoder) { struct imx_ldb_channel *imx_ldb_ch = enc_to_imx_ldb_ch(encoder); struct imx_ldb *ldb = imx_ldb_ch->ldb; - struct drm_display_mode *mode = &encoder->crtc->hwmode; u32 pixel_fmt; - unsigned long serial_clk; - unsigned long di_clk = mode->clock * 1000; - int mux = imx_drm_encoder_get_mux_id(imx_ldb_ch->child, encoder); - - if (ldb->ldb_ctrl & LDB_SPLIT_MODE_EN) { - /* dual channel LVDS mode */ - serial_clk = 3500UL * mode->clock; - imx_ldb_set_clock(ldb, mux, 0, serial_clk, di_clk); - imx_ldb_set_clock(ldb, mux, 1, serial_clk, di_clk); - } else { - serial_clk = 7000UL * mode->clock; - imx_ldb_set_clock(ldb, mux, imx_ldb_ch->chno, serial_clk, - di_clk); - } switch (imx_ldb_ch->chno) { case 0: @@ -247,6 +232,9 @@ static void imx_ldb_encoder_mode_set(struct drm_encoder *encoder, struct imx_ldb_channel *imx_ldb_ch = enc_to_imx_ldb_ch(encoder); struct imx_ldb *ldb = imx_ldb_ch->ldb; int dual = ldb->ldb_ctrl & LDB_SPLIT_MODE_EN; + unsigned long serial_clk; + unsigned long di_clk = mode->clock * 1000; + int mux = imx_drm_encoder_get_mux_id(imx_ldb_ch->child, encoder); if (mode->clock > 170000) { dev_warn(ldb->dev, @@ -257,6 +245,16 @@ static void imx_ldb_encoder_mode_set(struct drm_encoder *encoder, "%s: mode exceeds 85 MHz pixel clock\n", __func__); } + if (dual) { + serial_clk = 3500UL * mode->clock; + imx_ldb_set_clock(ldb, mux, 0, serial_clk, di_clk); + imx_ldb_set_clock(ldb, mux, 1, serial_clk, di_clk); + } else { + serial_clk = 7000UL * mode->clock; + imx_ldb_set_clock(ldb, mux, imx_ldb_ch->chno, serial_clk, + di_clk); + } + /* FIXME - assumes straight connections DI0 --> CH0, DI1 --> CH1 */ if (imx_ldb_ch == &ldb->channel[0]) { if (mode->flags & DRM_MODE_FLAG_NVSYNC) -- cgit v1.2.3-59-g8ed1b From d70e96ae05928643a7b10b8a519dc27afe4750d0 Mon Sep 17 00:00:00 2001 From: Liu Ying Date: Mon, 23 Feb 2015 11:09:51 +0800 Subject: DRM: i.MX: parallel display: Support probe deferral for finding DRM panel Signed-off-by: Liu Ying Signed-off-by: Philipp Zabel --- drivers/gpu/drm/imx/parallel-display.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/imx/parallel-display.c b/drivers/gpu/drm/imx/parallel-display.c index 5e83e007080f..900dda6a8e71 100644 --- a/drivers/gpu/drm/imx/parallel-display.c +++ b/drivers/gpu/drm/imx/parallel-display.c @@ -236,8 +236,11 @@ static int imx_pd_bind(struct device *dev, struct device *master, void *data) } panel_node = of_parse_phandle(np, "fsl,panel", 0); - if (panel_node) + if (panel_node) { imxpd->panel = of_drm_find_panel(panel_node); + if (!imxpd->panel) + return -EPROBE_DEFER; + } imxpd->dev = dev; -- cgit v1.2.3-59-g8ed1b From 31795b470b0872b66f7fa26f791b695c79821220 Mon Sep 17 00:00:00 2001 From: Boris Ostrovsky Date: Wed, 11 Feb 2015 14:39:18 -0500 Subject: x86/xen: Make sure X2APIC_ENABLE bit of MSR_IA32_APICBASE is not set Commit d524165cb8db ("x86/apic: Check x2apic early") tests X2APIC_ENABLE bit of MSR_IA32_APICBASE when CONFIG_X86_X2APIC is off and panics the kernel when this bit is set. Xen's PV guests will pass this MSR read to the hypervisor which will return its version of the MSR, where this bit might be set. Make sure we clear it before returning MSR value to the caller. Signed-off-by: Boris Ostrovsky Signed-off-by: David Vrabel --- arch/x86/xen/enlighten.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-) diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c index bd8b8459c3d0..efee14db009b 100644 --- a/arch/x86/xen/enlighten.c +++ b/arch/x86/xen/enlighten.c @@ -1070,6 +1070,23 @@ static inline void xen_write_cr8(unsigned long val) BUG_ON(val); } #endif + +static u64 xen_read_msr_safe(unsigned int msr, int *err) +{ + u64 val; + + val = native_read_msr_safe(msr, err); + switch (msr) { + case MSR_IA32_APICBASE: +#ifdef CONFIG_X86_X2APIC + if (!(cpuid_ecx(1) & (1 << (X86_FEATURE_X2APIC & 31)))) +#endif + val &= ~X2APIC_ENABLE; + break; + } + return val; +} + static int xen_write_msr_safe(unsigned int msr, unsigned low, unsigned high) { int ret; @@ -1240,7 +1257,7 @@ static const struct pv_cpu_ops xen_cpu_ops __initconst = { .wbinvd = native_wbinvd, - .read_msr = native_read_msr_safe, + .read_msr = xen_read_msr_safe, .write_msr = xen_write_msr_safe, .read_tsc = native_read_tsc, -- cgit v1.2.3-59-g8ed1b From fdfd811ddde3678247248ca9a27faa999ca4cd51 Mon Sep 17 00:00:00 2001 From: David Vrabel Date: Thu, 19 Feb 2015 15:23:17 +0000 Subject: x86/xen: allow privcmd hypercalls to be preempted Hypercalls submitted by user space tools via the privcmd driver can take a long time (potentially many 10s of seconds) if the hypercall has many sub-operations. A fully preemptible kernel may deschedule such as task in any upcall called from a hypercall continuation. However, in a kernel with voluntary or no preemption, hypercall continuations in Xen allow event handlers to be run but the task issuing the hypercall will not be descheduled until the hypercall is complete and the ioctl returns to user space. These long running tasks may also trigger the kernel's soft lockup detection. Add xen_preemptible_hcall_begin() and xen_preemptible_hcall_end() to bracket hypercalls that may be preempted. Use these in the privcmd driver. When returning from an upcall, call xen_maybe_preempt_hcall() which adds a schedule point if if the current task was within a preemptible hypercall. Since _cond_resched() can move the task to a different CPU, clear and set xen_in_preemptible_hcall around the call. Signed-off-by: David Vrabel Reviewed-by: Boris Ostrovsky --- arch/x86/kernel/entry_32.S | 3 +++ arch/x86/kernel/entry_64.S | 3 +++ drivers/xen/Makefile | 2 +- drivers/xen/preempt.c | 44 ++++++++++++++++++++++++++++++++++++++++++++ drivers/xen/privcmd.c | 2 ++ include/xen/xen-ops.h | 26 ++++++++++++++++++++++++++ 6 files changed, 79 insertions(+), 1 deletion(-) create mode 100644 drivers/xen/preempt.c diff --git a/arch/x86/kernel/entry_32.S b/arch/x86/kernel/entry_32.S index 000d4199b03e..31e2d5bf3e38 100644 --- a/arch/x86/kernel/entry_32.S +++ b/arch/x86/kernel/entry_32.S @@ -982,6 +982,9 @@ ENTRY(xen_hypervisor_callback) ENTRY(xen_do_upcall) 1: mov %esp, %eax call xen_evtchn_do_upcall +#ifndef CONFIG_PREEMPT + call xen_maybe_preempt_hcall +#endif jmp ret_from_intr CFI_ENDPROC ENDPROC(xen_hypervisor_callback) diff --git a/arch/x86/kernel/entry_64.S b/arch/x86/kernel/entry_64.S index db13655c3a2a..10074ad9ebf8 100644 --- a/arch/x86/kernel/entry_64.S +++ b/arch/x86/kernel/entry_64.S @@ -1208,6 +1208,9 @@ ENTRY(xen_do_hypervisor_callback) # do_hypervisor_callback(struct *pt_regs) popq %rsp CFI_DEF_CFA_REGISTER rsp decl PER_CPU_VAR(irq_count) +#ifndef CONFIG_PREEMPT + call xen_maybe_preempt_hcall +#endif jmp error_exit CFI_ENDPROC END(xen_do_hypervisor_callback) diff --git a/drivers/xen/Makefile b/drivers/xen/Makefile index 2140398a2a8c..2ccd3592d41f 100644 --- a/drivers/xen/Makefile +++ b/drivers/xen/Makefile @@ -2,7 +2,7 @@ ifeq ($(filter y, $(CONFIG_ARM) $(CONFIG_ARM64)),) obj-$(CONFIG_HOTPLUG_CPU) += cpu_hotplug.o endif obj-$(CONFIG_X86) += fallback.o -obj-y += grant-table.o features.o balloon.o manage.o +obj-y += grant-table.o features.o balloon.o manage.o preempt.o obj-y += events/ obj-y += xenbus/ diff --git a/drivers/xen/preempt.c b/drivers/xen/preempt.c new file mode 100644 index 000000000000..a1800c150839 --- /dev/null +++ b/drivers/xen/preempt.c @@ -0,0 +1,44 @@ +/* + * Preemptible hypercalls + * + * Copyright (C) 2014 Citrix Systems R&D ltd. + * + * This source code is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + */ + +#include +#include + +#ifndef CONFIG_PREEMPT + +/* + * Some hypercalls issued by the toolstack can take many 10s of + * seconds. Allow tasks running hypercalls via the privcmd driver to + * be voluntarily preempted even if full kernel preemption is + * disabled. + * + * Such preemptible hypercalls are bracketed by + * xen_preemptible_hcall_begin() and xen_preemptible_hcall_end() + * calls. + */ + +DEFINE_PER_CPU(bool, xen_in_preemptible_hcall); +EXPORT_SYMBOL_GPL(xen_in_preemptible_hcall); + +asmlinkage __visible void xen_maybe_preempt_hcall(void) +{ + if (unlikely(__this_cpu_read(xen_in_preemptible_hcall) + && should_resched())) { + /* + * Clear flag as we may be rescheduled on a different + * cpu. + */ + __this_cpu_write(xen_in_preemptible_hcall, false); + _cond_resched(); + __this_cpu_write(xen_in_preemptible_hcall, true); + } +} +#endif /* CONFIG_PREEMPT */ diff --git a/drivers/xen/privcmd.c b/drivers/xen/privcmd.c index 569a13b9e856..59ac71c4a043 100644 --- a/drivers/xen/privcmd.c +++ b/drivers/xen/privcmd.c @@ -56,10 +56,12 @@ static long privcmd_ioctl_hypercall(void __user *udata) if (copy_from_user(&hypercall, udata, sizeof(hypercall))) return -EFAULT; + xen_preemptible_hcall_begin(); ret = privcmd_call(hypercall.op, hypercall.arg[0], hypercall.arg[1], hypercall.arg[2], hypercall.arg[3], hypercall.arg[4]); + xen_preemptible_hcall_end(); return ret; } diff --git a/include/xen/xen-ops.h b/include/xen/xen-ops.h index 7491ee5d8164..83338210ee04 100644 --- a/include/xen/xen-ops.h +++ b/include/xen/xen-ops.h @@ -46,4 +46,30 @@ static inline efi_system_table_t __init *xen_efi_probe(void) } #endif +#ifdef CONFIG_PREEMPT + +static inline void xen_preemptible_hcall_begin(void) +{ +} + +static inline void xen_preemptible_hcall_end(void) +{ +} + +#else + +DECLARE_PER_CPU(bool, xen_in_preemptible_hcall); + +static inline void xen_preemptible_hcall_begin(void) +{ + __this_cpu_write(xen_in_preemptible_hcall, true); +} + +static inline void xen_preemptible_hcall_end(void) +{ + __this_cpu_write(xen_in_preemptible_hcall, false); +} + +#endif /* CONFIG_PREEMPT */ + #endif /* INCLUDE_XEN_OPS_H */ -- cgit v1.2.3-59-g8ed1b From facb5732b0bb59ebbc11b5d5abc249e677ddbeb6 Mon Sep 17 00:00:00 2001 From: Juergen Gross Date: Tue, 17 Feb 2015 08:02:47 +0100 Subject: xen-scsiback: mark pvscsi frontend request consumed only after last read A request in the ring buffer mustn't be read after it has been marked as consumed. Otherwise it might already have been reused by the frontend without violating the ring protocol. To avoid inconsistencies in the backend only work on a private copy of the request. This will ensure a malicious guest not being able to bypass consistency checks of the backend by modifying an active request. Signed-off-by: Juergen Gross Cc: Signed-off-by: David Vrabel --- drivers/xen/xen-scsiback.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-) diff --git a/drivers/xen/xen-scsiback.c b/drivers/xen/xen-scsiback.c index 61653a03a8f5..9faca6a60bb0 100644 --- a/drivers/xen/xen-scsiback.c +++ b/drivers/xen/xen-scsiback.c @@ -709,12 +709,11 @@ static int prepare_pending_reqs(struct vscsibk_info *info, static int scsiback_do_cmd_fn(struct vscsibk_info *info) { struct vscsiif_back_ring *ring = &info->ring; - struct vscsiif_request *ring_req; + struct vscsiif_request ring_req; struct vscsibk_pend *pending_req; RING_IDX rc, rp; int err, more_to_do; uint32_t result; - uint8_t act; rc = ring->req_cons; rp = ring->sring->req_prod; @@ -735,11 +734,10 @@ static int scsiback_do_cmd_fn(struct vscsibk_info *info) if (!pending_req) return 1; - ring_req = RING_GET_REQUEST(ring, rc); + ring_req = *RING_GET_REQUEST(ring, rc); ring->req_cons = ++rc; - act = ring_req->act; - err = prepare_pending_reqs(info, ring_req, pending_req); + err = prepare_pending_reqs(info, &ring_req, pending_req); if (err) { switch (err) { case -ENODEV: @@ -755,9 +753,9 @@ static int scsiback_do_cmd_fn(struct vscsibk_info *info) return 1; } - switch (act) { + switch (ring_req.act) { case VSCSIIF_ACT_SCSI_CDB: - if (scsiback_gnttab_data_map(ring_req, pending_req)) { + if (scsiback_gnttab_data_map(&ring_req, pending_req)) { scsiback_fast_flush_area(pending_req); scsiback_do_resp_with_sense(NULL, DRIVER_ERROR << 24, 0, pending_req); @@ -768,7 +766,7 @@ static int scsiback_do_cmd_fn(struct vscsibk_info *info) break; case VSCSIIF_ACT_SCSI_ABORT: scsiback_device_action(pending_req, TMR_ABORT_TASK, - ring_req->ref_rqid); + ring_req.ref_rqid); break; case VSCSIIF_ACT_SCSI_RESET: scsiback_device_action(pending_req, TMR_LUN_RESET, 0); -- cgit v1.2.3-59-g8ed1b From 5054daa285beaf706f051fbd395dc36c9f0f907f Mon Sep 17 00:00:00 2001 From: Boris Ostrovsky Date: Mon, 23 Feb 2015 11:01:00 -0500 Subject: x86/xen: Initialize cr4 shadow for 64-bit PV(H) guests Commit 1e02ce4cccdc ("x86: Store a per-cpu shadow copy of CR4") introduced CR4 shadows. These shadows are initialized in early boot code. The commit missed initialization for 64-bit PV(H) guests that this patch adds. Signed-off-by: Boris Ostrovsky Signed-off-by: David Vrabel --- arch/x86/xen/enlighten.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c index efee14db009b..5240f563076d 100644 --- a/arch/x86/xen/enlighten.c +++ b/arch/x86/xen/enlighten.c @@ -1758,6 +1758,7 @@ asmlinkage __visible void __init xen_start_kernel(void) #ifdef CONFIG_X86_32 i386_start_kernel(); #else + cr4_init_shadow(); /* 32b kernel does this in i386_start_kernel() */ x86_64_start_reservations((char *)__pa_symbol(&boot_params)); #endif } -- cgit v1.2.3-59-g8ed1b From 3a314f143d82603bd697d7eb6c76518afc3595bc Mon Sep 17 00:00:00 2001 From: Qiao Zhou Date: Wed, 4 Feb 2015 14:16:03 +0800 Subject: dmaenegine: mmp-pdma: fix irq handler overwrite physical chan issue Some dma channels may be reserved for other purpose in other layer, like secure driver in EL2/EL3. PDMA driver can see the interrupt status, but it should not try to handle related interrupt, since it doesn't belong to PDMA driver in kernel. These interrupts should be handled by corresponding client/module.Otherwise, it will overwrite illegal memory and cause unexpected issues, since pdma driver only requests resources for pdma channels. In PDMA driver, the reserved channels are at the end of total 32 channels. If we find interrupt bit index is not smaller than total dma channels, we should ignore it. Signed-off-by: Qiao Zhou Acked-by: Zhangfei Gao Signed-off-by: Vinod Koul --- drivers/dma/mmp_pdma.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/dma/mmp_pdma.c b/drivers/dma/mmp_pdma.c index 8926f271904e..abf1450bb25d 100644 --- a/drivers/dma/mmp_pdma.c +++ b/drivers/dma/mmp_pdma.c @@ -219,6 +219,9 @@ static irqreturn_t mmp_pdma_int_handler(int irq, void *dev_id) while (dint) { i = __ffs(dint); + /* only handle interrupts belonging to pdma driver*/ + if (i >= pdev->dma_channels) + break; dint &= (dint - 1); phy = &pdev->phy[i]; ret = mmp_pdma_chan_handler(irq, phy); -- cgit v1.2.3-59-g8ed1b From 52b68d7ef8838b4322da3dc35a05e02c63b05a0d Mon Sep 17 00:00:00 2001 From: Keith Busch Date: Mon, 23 Feb 2015 09:16:21 -0700 Subject: NVMe: Fix for BLK_DEV_INTEGRITY not set Need to define and use appropriate functions for when BLK_DEV_INTEGRITY is not set. Reported-by: Fengguang Wu Signed-off-by: Keith Busch Signed-off-by: Jens Axboe --- drivers/block/nvme-core.c | 99 +++++++++++++++++++++++++++-------------------- 1 file changed, 58 insertions(+), 41 deletions(-) diff --git a/drivers/block/nvme-core.c b/drivers/block/nvme-core.c index b64bccbb78c9..ceb32dd52a6c 100644 --- a/drivers/block/nvme-core.c +++ b/drivers/block/nvme-core.c @@ -482,6 +482,7 @@ static int nvme_error_status(u16 status) } } +#ifdef CONFIG_BLK_DEV_INTEGRITY static void nvme_dif_prep(u32 p, u32 v, struct t10_pi_tuple *pi) { if (be32_to_cpu(pi->ref_tag) == v) @@ -538,6 +539,58 @@ static void nvme_dif_remap(struct request *req, kunmap_atomic(pmap); } +static int nvme_noop_verify(struct blk_integrity_iter *iter) +{ + return 0; +} + +static int nvme_noop_generate(struct blk_integrity_iter *iter) +{ + return 0; +} + +struct blk_integrity nvme_meta_noop = { + .name = "NVME_META_NOOP", + .generate_fn = nvme_noop_generate, + .verify_fn = nvme_noop_verify, +}; + +static void nvme_init_integrity(struct nvme_ns *ns) +{ + struct blk_integrity integrity; + + switch (ns->pi_type) { + case NVME_NS_DPS_PI_TYPE3: + integrity = t10_pi_type3_crc; + break; + case NVME_NS_DPS_PI_TYPE1: + case NVME_NS_DPS_PI_TYPE2: + integrity = t10_pi_type1_crc; + break; + default: + integrity = nvme_meta_noop; + break; + } + integrity.tuple_size = ns->ms; + blk_integrity_register(ns->disk, &integrity); + blk_queue_max_integrity_segments(ns->queue, 1); +} +#else /* CONFIG_BLK_DEV_INTEGRITY */ +static void nvme_dif_remap(struct request *req, + void (*dif_swap)(u32 p, u32 v, struct t10_pi_tuple *pi)) +{ +} +static void nvme_dif_prep(u32 p, u32 v, struct t10_pi_tuple *pi) +{ +} +static void nvme_dif_complete(u32 p, u32 v, struct t10_pi_tuple *pi) +{ +} +static void nvme_init_integrity(struct nvme_ns *ns) +{ +} +#endif + static void req_completion(struct nvme_queue *nvmeq, void *ctx, struct nvme_completion *cqe) { @@ -1959,43 +2012,6 @@ static void nvme_config_discard(struct nvme_ns *ns) queue_flag_set_unlocked(QUEUE_FLAG_DISCARD, ns->queue); } -static int nvme_noop_verify(struct blk_integrity_iter *iter) -{ - return 0; -} - -static int nvme_noop_generate(struct blk_integrity_iter *iter) -{ - return 0; -} - -struct blk_integrity nvme_meta_noop = { - .name = "NVME_META_NOOP", - .generate_fn = nvme_noop_generate, - .verify_fn = nvme_noop_verify, -}; - -static void nvme_init_integrity(struct nvme_ns *ns) -{ - struct blk_integrity integrity; - - switch (ns->pi_type) { - case NVME_NS_DPS_PI_TYPE3: - integrity = t10_pi_type3_crc; - break; - case NVME_NS_DPS_PI_TYPE1: - case NVME_NS_DPS_PI_TYPE2: - integrity = t10_pi_type1_crc; - break; - default: - integrity = nvme_meta_noop; - break; - } - integrity.tuple_size = ns->ms; - blk_integrity_register(ns->disk, &integrity); - blk_queue_max_integrity_segments(ns->queue, 1); -} - static int nvme_revalidate_disk(struct gendisk *disk) { struct nvme_ns *ns = disk->private_data; @@ -2036,7 +2052,8 @@ static int nvme_revalidate_disk(struct gendisk *disk) pi_type = ns->ms == sizeof(struct t10_pi_tuple) ? id->dps & NVME_NS_DPS_PI_MASK : 0; - if (disk->integrity && (ns->pi_type != pi_type || ns->ms != old_ms || + if (blk_get_integrity(disk) && (ns->pi_type != pi_type || + ns->ms != old_ms || bs != queue_logical_block_size(disk->queue) || (ns->ms && id->flbas & NVME_NS_FLBAS_META_EXT))) blk_integrity_unregister(disk); @@ -2044,11 +2061,11 @@ static int nvme_revalidate_disk(struct gendisk *disk) ns->pi_type = pi_type; blk_queue_logical_block_size(ns->queue, bs); - if (ns->ms && !disk->integrity && (disk->flags & GENHD_FL_UP) && + if (ns->ms && !blk_get_integrity(disk) && (disk->flags & GENHD_FL_UP) && !(id->flbas & NVME_NS_FLBAS_META_EXT)) nvme_init_integrity(ns); - if (id->ncap == 0 || (ns->ms && !disk->integrity)) + if (id->ncap == 0 || (ns->ms && !blk_get_integrity(disk))) set_capacity(disk, 0); else set_capacity(disk, le64_to_cpup(&id->nsze) << (ns->lba_shift - 9)); @@ -2652,7 +2669,7 @@ static void nvme_dev_remove(struct nvme_dev *dev) list_for_each_entry(ns, &dev->namespaces, list) { if (ns->disk->flags & GENHD_FL_UP) { - if (ns->disk->integrity) + if (blk_get_integrity(ns->disk)) blk_integrity_unregister(ns->disk); del_gendisk(ns->disk); } -- cgit v1.2.3-59-g8ed1b From f0774d884bad7007b54cfffb5c93c23420c75aa6 Mon Sep 17 00:00:00 2001 From: Sasha Levin Date: Mon, 23 Feb 2015 05:38:00 -0500 Subject: mm: shmem: check for mapping owner before dereferencing mapping->host can be NULL and shouldn't be dereferenced before being checked. [ 1295.741844] GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] SMP KASAN [ 1295.746387] Dumping ftrace buffer: [ 1295.748217] (ftrace buffer empty) [ 1295.749527] Modules linked in: [ 1295.750268] CPU: 62 PID: 23410 Comm: trinity-c70 Not tainted 3.19.0-next-20150219-sasha-00045-g9130270f #1939 [ 1295.750268] task: ffff8803a49db000 ti: ffff8803a4dc8000 task.ti: ffff8803a4dc8000 [ 1295.750268] RIP: shmem_mapping (mm/shmem.c:1458) [ 1295.750268] RSP: 0000:ffff8803a4dcfbf8 EFLAGS: 00010206 [ 1295.750268] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 00000000000f2804 [ 1295.750268] RDX: 0000000000000005 RSI: 0400000000000794 RDI: 0000000000000028 [ 1295.750268] RBP: ffff8803a4dcfc08 R08: 0000000000000000 R09: 00000000031de000 [ 1295.750268] R10: dffffc0000000000 R11: 00000000031c1000 R12: 0400000000000794 [ 1295.750268] R13: 00000000031c2000 R14: 00000000031de000 R15: ffff880e3bdc1000 [ 1295.750268] FS: 00007f8703c7e700(0000) GS:ffff881164800000(0000) knlGS:0000000000000000 [ 1295.750268] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1295.750268] CR2: 0000000004e58000 CR3: 00000003a9f3c000 CR4: 00000000000007a0 [ 1295.750268] DR0: ffffffff81000000 DR1: 0000009494949494 DR2: 0000000000000000 [ 1295.750268] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 00000000000d0602 [ 1295.750268] Stack: [ 1295.750268] ffff8803a4dcfec8 ffffffffbb1dc770 ffff8803a4dcfc38 ffffffffad6f230b [ 1295.750268] ffffffffad6f2b0d 0000014100000000 ffff88001e17c08b ffff880d9453fe08 [ 1295.750268] ffff8803a4dcfd18 ffffffffad6f2ce2 ffff8803a49dbcd8 ffff8803a49dbce0 [ 1295.750268] Call Trace: [ 1295.750268] mincore_page (mm/mincore.c:61) [ 1295.750268] ? mincore_pte_range (include/linux/spinlock.h:312 mm/mincore.c:131) [ 1295.750268] mincore_pte_range (mm/mincore.c:151) [ 1295.750268] ? mincore_unmapped_range (mm/mincore.c:113) [ 1295.750268] __walk_page_range (mm/pagewalk.c:51 mm/pagewalk.c:90 mm/pagewalk.c:116 mm/pagewalk.c:204) [ 1295.750268] walk_page_range (mm/pagewalk.c:275) [ 1295.750268] SyS_mincore (mm/mincore.c:191 mm/mincore.c:253 mm/mincore.c:220) [ 1295.750268] ? mincore_pte_range (mm/mincore.c:220) [ 1295.750268] ? mincore_unmapped_range (mm/mincore.c:113) [ 1295.750268] ? __mincore_unmapped_range (mm/mincore.c:105) [ 1295.750268] ? ptlock_free (mm/mincore.c:24) [ 1295.750268] ? syscall_trace_enter (arch/x86/kernel/ptrace.c:1610) [ 1295.750268] ia32_do_call (arch/x86/ia32/ia32entry.S:446) [ 1295.750268] Code: e5 48 c1 ea 03 53 48 89 fb 48 83 ec 08 80 3c 02 00 75 4f 48 b8 00 00 00 00 00 fc ff df 48 8b 1b 48 8d 7b 28 48 89 fa 48 c1 ea 03 <80> 3c 02 00 75 3f 48 b8 00 00 00 00 00 fc ff df 48 8b 5b 28 48 All code ======== 0: e5 48 in $0x48,%eax 2: c1 ea 03 shr $0x3,%edx 5: 53 push %rbx 6: 48 89 fb mov %rdi,%rbx 9: 48 83 ec 08 sub $0x8,%rsp d: 80 3c 02 00 cmpb $0x0,(%rdx,%rax,1) 11: 75 4f jne 0x62 13: 48 b8 00 00 00 00 00 movabs $0xdffffc0000000000,%rax 1a: fc ff df 1d: 48 8b 1b mov (%rbx),%rbx 20: 48 8d 7b 28 lea 0x28(%rbx),%rdi 24: 48 89 fa mov %rdi,%rdx 27: 48 c1 ea 03 shr $0x3,%rdx 2b:* 80 3c 02 00 cmpb $0x0,(%rdx,%rax,1) <-- trapping instruction 2f: 75 3f jne 0x70 31: 48 b8 00 00 00 00 00 movabs $0xdffffc0000000000,%rax 38: fc ff df 3b: 48 8b 5b 28 mov 0x28(%rbx),%rbx 3f: 48 rex.W ... Code starting with the faulting instruction =========================================== 0: 80 3c 02 00 cmpb $0x0,(%rdx,%rax,1) 4: 75 3f jne 0x45 6: 48 b8 00 00 00 00 00 movabs $0xdffffc0000000000,%rax d: fc ff df 10: 48 8b 5b 28 mov 0x28(%rbx),%rbx 14: 48 rex.W ... [ 1295.750268] RIP shmem_mapping (mm/shmem.c:1458) [ 1295.750268] RSP Fixes: 97b713ba3e ("fs: kill BDI_CAP_SWAP_BACKED") Signed-off-by: Sasha Levin Reviewed-by: Christoph Hellwig Signed-off-by: Jens Axboe --- mm/shmem.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/mm/shmem.c b/mm/shmem.c index 2f17cb5f00a4..cf2d0ca010bc 100644 --- a/mm/shmem.c +++ b/mm/shmem.c @@ -1455,6 +1455,9 @@ static struct inode *shmem_get_inode(struct super_block *sb, const struct inode bool shmem_mapping(struct address_space *mapping) { + if (!mapping->host) + return false; + return mapping->host->i_sb->s_op == &shmem_ops; } -- cgit v1.2.3-59-g8ed1b From 71bb0012c38fbd090a56b3cb96e9f626c415d264 Mon Sep 17 00:00:00 2001 From: Sasha Levin Date: Mon, 23 Feb 2015 04:35:06 -0500 Subject: rhashtable: initialize all rhashtable walker members Commit f2dba9c6ff ("rhashtable: Introduce rhashtable_walk_*") forgot to initialize the members of struct rhashtable_walker after allocating it, which caused an undefined value for 'resize' which is used later on. Fixes: f2dba9c6ff ("rhashtable: Introduce rhashtable_walk_*") Signed-off-by: Sasha Levin Signed-off-by: David S. Miller --- lib/rhashtable.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/lib/rhashtable.c b/lib/rhashtable.c index b41a5c09832a..e3a04e4b3ec5 100644 --- a/lib/rhashtable.c +++ b/lib/rhashtable.c @@ -903,6 +903,9 @@ int rhashtable_walk_init(struct rhashtable *ht, struct rhashtable_iter *iter) if (!iter->walker) return -ENOMEM; + INIT_LIST_HEAD(&iter->walker->list); + iter->walker->resize = false; + mutex_lock(&ht->mutex); list_add(&iter->walker->list, &ht->walkers); mutex_unlock(&ht->mutex); -- cgit v1.2.3-59-g8ed1b From 46b9e4bb76ee26f1e024e048bb95af41b763f48f Mon Sep 17 00:00:00 2001 From: Rasmus Villemoes Date: Mon, 23 Feb 2015 12:02:51 +0100 Subject: decnet: Fix obvious o/0 typo Signed-off-by: Rasmus Villemoes Signed-off-by: David S. Miller --- net/decnet/dn_route.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/decnet/dn_route.c b/net/decnet/dn_route.c index 1d7c1256e845..3b81092771f8 100644 --- a/net/decnet/dn_route.c +++ b/net/decnet/dn_route.c @@ -1062,7 +1062,7 @@ source_ok: if (decnet_debug_level & 16) printk(KERN_DEBUG "dn_route_output_slow: initial checks complete." - " dst=%o4x src=%04x oif=%d try_hard=%d\n", + " dst=%04x src=%04x oif=%d try_hard=%d\n", le16_to_cpu(fld.daddr), le16_to_cpu(fld.saddr), fld.flowidn_oif, try_hard); -- cgit v1.2.3-59-g8ed1b From 57e595631904c827cfa1a0f7bbd7cc9a49da5745 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Mon, 23 Feb 2015 14:02:54 +0100 Subject: team: fix possible null pointer dereference in team_handle_frame Currently following race is possible in team: CPU0 CPU1 team_port_del team_upper_dev_unlink priv_flags &= ~IFF_TEAM_PORT team_handle_frame team_port_get_rcu team_port_exists priv_flags & IFF_TEAM_PORT == 0 return NULL (instead of port got from rx_handler_data) netdev_rx_handler_unregister The thing is that the flag is removed before rx_handler is unregistered. If team_handle_frame is called in between, team_port_exists returns 0 and team_port_get_rcu will return NULL. So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister that team_handle_frame will always see valid rx_handler_data pointer. Signed-off-by: Jiri Pirko Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Signed-off-by: David S. Miller --- drivers/net/team/team.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/net/team/team.c b/drivers/net/team/team.c index 0e62274e884a..f1ee71e22241 100644 --- a/drivers/net/team/team.c +++ b/drivers/net/team/team.c @@ -43,9 +43,7 @@ static struct team_port *team_port_get_rcu(const struct net_device *dev) { - struct team_port *port = rcu_dereference(dev->rx_handler_data); - - return team_port_exists(dev) ? port : NULL; + return rcu_dereference(dev->rx_handler_data); } static struct team_port *team_port_get_rtnl(const struct net_device *dev) -- cgit v1.2.3-59-g8ed1b From a050dfb21cc22ac0c666d52531040c1bc48184cc Mon Sep 17 00:00:00 2001 From: Jan Kiszka Date: Sat, 7 Feb 2015 22:21:20 +0100 Subject: ARM: KVM: Fix size check in __coherent_cache_guest_page The check is supposed to catch page-unaligned sizes, not the inverse. Signed-off-by: Jan Kiszka Signed-off-by: Christoffer Dall --- arch/arm/include/asm/kvm_mmu.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/include/asm/kvm_mmu.h b/arch/arm/include/asm/kvm_mmu.h index 37ca2a4c6f09..bf0fe99e8ca9 100644 --- a/arch/arm/include/asm/kvm_mmu.h +++ b/arch/arm/include/asm/kvm_mmu.h @@ -207,7 +207,7 @@ static inline void __coherent_cache_guest_page(struct kvm_vcpu *vcpu, pfn_t pfn, bool need_flush = !vcpu_has_cache_enabled(vcpu) || ipa_uncached; - VM_BUG_ON(size & PAGE_MASK); + VM_BUG_ON(size & ~PAGE_MASK); if (!need_flush && !icache_is_pipt()) goto vipt_cache; -- cgit v1.2.3-59-g8ed1b From 91314cb0053877991fd7b4749bb4b54d6bd6992f Mon Sep 17 00:00:00 2001 From: Wei Huang Date: Fri, 30 Jan 2015 13:09:26 -0500 Subject: arm/arm64: KVM: Add exit reaons to kvm_exit event tracing This patch extends trace_kvm_exit() to include KVM exit reasons (i.e. EC of HSR). The tracing function then dumps both exit reason and PC of vCPU, shown as the following. Tracing tools can use this new exit_reason field to better understand the behavior of guest VMs. 886.301252: kvm_exit: HSR_EC: 0x0024, PC: 0xfffffe0000506b28 Signed-off-by: Wei Huang Signed-off-by: Christoffer Dall --- arch/arm/kvm/arm.c | 2 +- arch/arm/kvm/trace.h | 10 +++++++--- 2 files changed, 8 insertions(+), 4 deletions(-) diff --git a/arch/arm/kvm/arm.c b/arch/arm/kvm/arm.c index 07e7eb1d7ab6..5560f74f9eee 100644 --- a/arch/arm/kvm/arm.c +++ b/arch/arm/kvm/arm.c @@ -540,7 +540,7 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu, struct kvm_run *run) vcpu->mode = OUTSIDE_GUEST_MODE; kvm_guest_exit(); - trace_kvm_exit(*vcpu_pc(vcpu)); + trace_kvm_exit(kvm_vcpu_trap_get_class(vcpu), *vcpu_pc(vcpu)); /* * We may have taken a host interrupt in HYP mode (ie * while executing the guest). This interrupt is still diff --git a/arch/arm/kvm/trace.h b/arch/arm/kvm/trace.h index 881874b1a036..6817664b46b8 100644 --- a/arch/arm/kvm/trace.h +++ b/arch/arm/kvm/trace.h @@ -25,18 +25,22 @@ TRACE_EVENT(kvm_entry, ); TRACE_EVENT(kvm_exit, - TP_PROTO(unsigned long vcpu_pc), - TP_ARGS(vcpu_pc), + TP_PROTO(unsigned int exit_reason, unsigned long vcpu_pc), + TP_ARGS(exit_reason, vcpu_pc), TP_STRUCT__entry( + __field( unsigned int, exit_reason ) __field( unsigned long, vcpu_pc ) ), TP_fast_assign( + __entry->exit_reason = exit_reason; __entry->vcpu_pc = vcpu_pc; ), - TP_printk("PC: 0x%08lx", __entry->vcpu_pc) + TP_printk("HSR_EC: 0x%04x, PC: 0x%08lx", + __entry->exit_reason, + __entry->vcpu_pc) ); TRACE_EVENT(kvm_guest_fault, -- cgit v1.2.3-59-g8ed1b From 21bc8dc5b729dbeecb43adff23b74b51321e1897 Mon Sep 17 00:00:00 2001 From: Radim Krčmář Date: Mon, 16 Feb 2015 15:36:33 +0100 Subject: KVM: VMX: fix build without CONFIG_SMP MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit 'apic' is not defined if !CONFIG_X86_64 && !CONFIG_X86_LOCAL_APIC. Posted interrupt makes no sense without CONFIG_SMP, and CONFIG_X86_LOCAL_APIC will be set with it. Reported-by: kbuild test robot Signed-off-by: Radim Krčmář Signed-off-by: Paolo Bonzini --- arch/x86/kvm/vmx.c | 23 ++++++++++++++--------- 1 file changed, 14 insertions(+), 9 deletions(-) diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c index 14c1a18d206a..f7b20b417a3a 100644 --- a/arch/x86/kvm/vmx.c +++ b/arch/x86/kvm/vmx.c @@ -4367,6 +4367,18 @@ static int vmx_complete_nested_posted_interrupt(struct kvm_vcpu *vcpu) return 0; } +static inline bool kvm_vcpu_trigger_posted_interrupt(struct kvm_vcpu *vcpu) +{ +#ifdef CONFIG_SMP + if (vcpu->mode == IN_GUEST_MODE) { + apic->send_IPI_mask(get_cpu_mask(vcpu->cpu), + POSTED_INTR_VECTOR); + return true; + } +#endif + return false; +} + static int vmx_deliver_nested_posted_interrupt(struct kvm_vcpu *vcpu, int vector) { @@ -4375,9 +4387,7 @@ static int vmx_deliver_nested_posted_interrupt(struct kvm_vcpu *vcpu, if (is_guest_mode(vcpu) && vector == vmx->nested.posted_intr_nv) { /* the PIR and ON have been set by L1. */ - if (vcpu->mode == IN_GUEST_MODE) - apic->send_IPI_mask(get_cpu_mask(vcpu->cpu), - POSTED_INTR_VECTOR); + kvm_vcpu_trigger_posted_interrupt(vcpu); /* * If a posted intr is not recognized by hardware, * we will accomplish it in the next vmentry. @@ -4409,12 +4419,7 @@ static void vmx_deliver_posted_interrupt(struct kvm_vcpu *vcpu, int vector) r = pi_test_and_set_on(&vmx->pi_desc); kvm_make_request(KVM_REQ_EVENT, vcpu); -#ifdef CONFIG_SMP - if (!r && (vcpu->mode == IN_GUEST_MODE)) - apic->send_IPI_mask(get_cpu_mask(vcpu->cpu), - POSTED_INTR_VECTOR); - else -#endif + if (r || !kvm_vcpu_trigger_posted_interrupt(vcpu)) kvm_vcpu_kick(vcpu); } -- cgit v1.2.3-59-g8ed1b From 4ff6f8e61eb7f96d3ca535c6d240f863ccd6fb7d Mon Sep 17 00:00:00 2001 From: Paolo Bonzini Date: Thu, 12 Feb 2015 17:04:47 +0100 Subject: KVM: emulate: fix CMPXCHG8B on 32-bit hosts This has been broken for a long time: it broke first in 2.6.35, then was almost fixed in 2.6.36 but this one-liner slipped through the cracks. The bug shows up as an infinite loop in Windows 7 (and newer) boot on 32-bit hosts without EPT. Windows uses CMPXCHG8B to write to page tables, which causes a page fault if running without EPT; the emulator is then called from kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are not 0; the common case for this is that the NX bit (bit 63) is 1. Fixes: 6550e1f165f384f3a46b60a1be9aba4bc3c2adad Fixes: 16518d5ada690643453eb0aef3cc7841d3623c2d Cc: stable@vger.kernel.org # 2.6.35+ Reported-by: Erik Rull Tested-by: Erik Rull Signed-off-by: Paolo Bonzini --- arch/x86/kvm/emulate.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/x86/kvm/emulate.c b/arch/x86/kvm/emulate.c index e0b794a84c35..106c01557f2b 100644 --- a/arch/x86/kvm/emulate.c +++ b/arch/x86/kvm/emulate.c @@ -4950,7 +4950,8 @@ int x86_emulate_insn(struct x86_emulate_ctxt *ctxt) goto done; } } - ctxt->dst.orig_val = ctxt->dst.val; + /* Copy full 64-bit value for CMPXCHG8B. */ + ctxt->dst.orig_val64 = ctxt->dst.val64; special_insn: -- cgit v1.2.3-59-g8ed1b From 30ff54765976e132674e3eae2071ed8ed494665c Mon Sep 17 00:00:00 2001 From: Jamal Hadi Salim Date: Mon, 23 Feb 2015 08:17:12 -0500 Subject: net: sched: export tc_connmark.h so it is uapi accessible Signed-off-by: Jamal Hadi Salim Signed-off-by: David S. Miller --- include/uapi/linux/tc_act/Kbuild | 1 + 1 file changed, 1 insertion(+) diff --git a/include/uapi/linux/tc_act/Kbuild b/include/uapi/linux/tc_act/Kbuild index 19d5219b0b99..242cf0c6e33d 100644 --- a/include/uapi/linux/tc_act/Kbuild +++ b/include/uapi/linux/tc_act/Kbuild @@ -9,3 +9,4 @@ header-y += tc_pedit.h header-y += tc_skbedit.h header-y += tc_vlan.h header-y += tc_bpf.h +header-y += tc_connmark.h -- cgit v1.2.3-59-g8ed1b From 9b1dcbc8cf4679ecf090b343ac31bda6e55ddabe Mon Sep 17 00:00:00 2001 From: Chuck Lever Date: Thu, 12 Feb 2015 10:14:51 -0500 Subject: xprtrdma: Store RDMA credits in unsigned variables Dan Carpenter's static checker pointed out: net/sunrpc/xprtrdma/rpc_rdma.c:879 rpcrdma_reply_handler() warn: can 'credits' be negative? "credits" is defined as an int. The credits value comes from the server as a 32-bit unsigned integer. A malicious or broken server can plant a large unsigned integer in that field which would result in an underflow in the following logic, potentially triggering a deadlock of the mount point by blocking the client from issuing more RPC requests. net/sunrpc/xprtrdma/rpc_rdma.c: 876 credits = be32_to_cpu(headerp->rm_credit); 877 if (credits == 0) 878 credits = 1; /* don't deadlock */ 879 else if (credits > r_xprt->rx_buf.rb_max_requests) 880 credits = r_xprt->rx_buf.rb_max_requests; 881 882 cwnd = xprt->cwnd; 883 xprt->cwnd = credits << RPC_CWNDSHIFT; 884 if (xprt->cwnd > cwnd) 885 xprt_release_rqst_cong(rqst->rq_task); Reported-by: Dan Carpenter Fixes: eba8ff660b2d ("xprtrdma: Move credit update to RPC . . .") Signed-off-by: Chuck Lever Signed-off-by: Anna Schumaker --- net/sunrpc/xprtrdma/rpc_rdma.c | 3 ++- net/sunrpc/xprtrdma/xprt_rdma.h | 2 +- 2 files changed, 3 insertions(+), 2 deletions(-) diff --git a/net/sunrpc/xprtrdma/rpc_rdma.c b/net/sunrpc/xprtrdma/rpc_rdma.c index 7e9acd9361c5..91ffde82fa0c 100644 --- a/net/sunrpc/xprtrdma/rpc_rdma.c +++ b/net/sunrpc/xprtrdma/rpc_rdma.c @@ -738,8 +738,9 @@ rpcrdma_reply_handler(struct rpcrdma_rep *rep) struct rpc_xprt *xprt = rep->rr_xprt; struct rpcrdma_xprt *r_xprt = rpcx_to_rdmax(xprt); __be32 *iptr; - int credits, rdmalen, status; + int rdmalen, status; unsigned long cwnd; + u32 credits; /* Check status. If bad, signal disconnect and return rep to pool */ if (rep->rr_len == ~0U) { diff --git a/net/sunrpc/xprtrdma/xprt_rdma.h b/net/sunrpc/xprtrdma/xprt_rdma.h index d1b70397c60f..0a16fb6f0885 100644 --- a/net/sunrpc/xprtrdma/xprt_rdma.h +++ b/net/sunrpc/xprtrdma/xprt_rdma.h @@ -285,7 +285,7 @@ rpcr_to_rdmar(struct rpc_rqst *rqst) */ struct rpcrdma_buffer { spinlock_t rb_lock; /* protects indexes */ - int rb_max_requests;/* client max requests */ + u32 rb_max_requests;/* client max requests */ struct list_head rb_mws; /* optional memory windows/fmrs/frmrs */ struct list_head rb_all; int rb_send_index; -- cgit v1.2.3-59-g8ed1b From a948f8ce771a1f07c17ed8bcb51f59f69129a51c Mon Sep 17 00:00:00 2001 From: Fabian Frederick Date: Mon, 23 Feb 2015 18:38:24 +0100 Subject: irda: replace current->state by set_current_state() Use helper functions to access current->state. Direct assignments are prone to races and therefore buggy. current->state = TASK_RUNNING can be replaced by __set_current_state() Thanks to Peter Zijlstra for the exact definition of the problem. Suggested-By: Peter Zijlstra Signed-off-by: Fabian Frederick Signed-off-by: David S. Miller --- net/irda/ircomm/ircomm_tty.c | 2 +- net/irda/irnet/irnet_ppp.c | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/net/irda/ircomm/ircomm_tty.c b/net/irda/ircomm/ircomm_tty.c index 40695b9751c1..9940a41efca1 100644 --- a/net/irda/ircomm/ircomm_tty.c +++ b/net/irda/ircomm/ircomm_tty.c @@ -811,7 +811,7 @@ static void ircomm_tty_wait_until_sent(struct tty_struct *tty, int timeout) break; } spin_unlock_irqrestore(&self->spinlock, flags); - current->state = TASK_RUNNING; + __set_current_state(TASK_RUNNING); } /* diff --git a/net/irda/irnet/irnet_ppp.c b/net/irda/irnet/irnet_ppp.c index 3c83a1e5ab03..1215693fdd22 100644 --- a/net/irda/irnet/irnet_ppp.c +++ b/net/irda/irnet/irnet_ppp.c @@ -305,7 +305,7 @@ irnet_ctrl_read(irnet_socket * ap, /* Put ourselves on the wait queue to be woken up */ add_wait_queue(&irnet_events.rwait, &wait); - current->state = TASK_INTERRUPTIBLE; + set_current_state(TASK_INTERRUPTIBLE); for(;;) { /* If there is unread events */ @@ -321,7 +321,7 @@ irnet_ctrl_read(irnet_socket * ap, /* Yield and wait to be woken up */ schedule(); } - current->state = TASK_RUNNING; + __set_current_state(TASK_RUNNING); remove_wait_queue(&irnet_events.rwait, &wait); /* Did we got it ? */ -- cgit v1.2.3-59-g8ed1b From d720d8cec563ce4e4fa44a613d4f2dcb1caf2998 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Mon, 23 Feb 2015 18:12:56 +0000 Subject: net: compat: Ignore MSG_CMSG_COMPAT in compat_sys_{send, recv}msg With commit a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg), the MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points, changing the kernel compat behaviour from the one before the commit it was trying to fix (1be374a0518a, net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg). On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native 32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by the kernel). However, on a 64-bit kernel, the compat ABI is different with commit a7526eb5d06b. This patch changes the compat_sys_{send,recv}msg behaviour to the one prior to commit 1be374a0518a. The problem was found running 32-bit LTP (sendmsg01) binary on an arm64 kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg() but the general rule is not to break user ABI (even when the user behaviour is not entirely sane). Fixes: a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg) Cc: Andy Lutomirski Cc: David S. Miller Signed-off-by: Catalin Marinas Signed-off-by: David S. Miller --- net/compat.c | 9 --------- 1 file changed, 9 deletions(-) diff --git a/net/compat.c b/net/compat.c index 3236b4167a32..94d3d5e97883 100644 --- a/net/compat.c +++ b/net/compat.c @@ -711,24 +711,18 @@ static unsigned char nas[21] = { COMPAT_SYSCALL_DEFINE3(sendmsg, int, fd, struct compat_msghdr __user *, msg, unsigned int, flags) { - if (flags & MSG_CMSG_COMPAT) - return -EINVAL; return __sys_sendmsg(fd, (struct user_msghdr __user *)msg, flags | MSG_CMSG_COMPAT); } COMPAT_SYSCALL_DEFINE4(sendmmsg, int, fd, struct compat_mmsghdr __user *, mmsg, unsigned int, vlen, unsigned int, flags) { - if (flags & MSG_CMSG_COMPAT) - return -EINVAL; return __sys_sendmmsg(fd, (struct mmsghdr __user *)mmsg, vlen, flags | MSG_CMSG_COMPAT); } COMPAT_SYSCALL_DEFINE3(recvmsg, int, fd, struct compat_msghdr __user *, msg, unsigned int, flags) { - if (flags & MSG_CMSG_COMPAT) - return -EINVAL; return __sys_recvmsg(fd, (struct user_msghdr __user *)msg, flags | MSG_CMSG_COMPAT); } @@ -751,9 +745,6 @@ COMPAT_SYSCALL_DEFINE5(recvmmsg, int, fd, struct compat_mmsghdr __user *, mmsg, int datagrams; struct timespec ktspec; - if (flags & MSG_CMSG_COMPAT) - return -EINVAL; - if (timeout == NULL) return __sys_recvmmsg(fd, (struct mmsghdr __user *)mmsg, vlen, flags | MSG_CMSG_COMPAT, NULL); -- cgit v1.2.3-59-g8ed1b From a5cb514f1f689a48595370a368b568e2f551ddfd Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Wed, 3 Dec 2014 14:41:47 +0100 Subject: drivers: sh: Disable PM runtime for multi-platform r8a7740 with genpd If the default PM domain using PM_CLK is used for PM runtime, the real PM domain(s) cannot be registered from DT later. Hence do not enable it when running a multi-platform kernel with genpd support on an r8a7740. The R-Mobile PM domain driver will take care of PM runtime management of the module clocks. The default PM domain is still needed for: - platforms without genpd support, - the legacy (non-DT) case, where genpd may take over later, except for the C5 "always on" PM domain. Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- drivers/sh/pm_runtime.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/sh/pm_runtime.c b/drivers/sh/pm_runtime.c index f3ee439d6f0e..cd4c293f0dd0 100644 --- a/drivers/sh/pm_runtime.c +++ b/drivers/sh/pm_runtime.c @@ -81,7 +81,9 @@ static int __init sh_pm_runtime_init(void) if (!of_machine_is_compatible("renesas,emev2") && !of_machine_is_compatible("renesas,r7s72100") && !of_machine_is_compatible("renesas,r8a73a4") && +#ifndef CONFIG_PM_GENERIC_DOMAINS_OF !of_machine_is_compatible("renesas,r8a7740") && +#endif !of_machine_is_compatible("renesas,r8a7778") && !of_machine_is_compatible("renesas,r8a7779") && !of_machine_is_compatible("renesas,r8a7790") && -- cgit v1.2.3-59-g8ed1b From fe6e4081a626d2987b73c9b15ed520b4f22d585f Mon Sep 17 00:00:00 2001 From: Vlastimil Setka Date: Mon, 23 Feb 2015 11:27:37 -0600 Subject: altera_tse: Correct typo in obtaining tx_fifo_depth from devicetree This patch corrects a typo in the way tx_fifo_depth is read from the devicetree. This patch was submitted by Vlastimil about a week ago, and is now cleaned up and resubmitted. Signed-off-by: Vlastimil Setka Signed-off-by: Vince Bridgers Signed-off-by: David S. Miller --- drivers/net/ethernet/altera/altera_tse_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/altera/altera_tse_main.c b/drivers/net/ethernet/altera/altera_tse_main.c index 760c72c6e2ac..f3d784a3463d 100644 --- a/drivers/net/ethernet/altera/altera_tse_main.c +++ b/drivers/net/ethernet/altera/altera_tse_main.c @@ -1399,7 +1399,7 @@ static int altera_tse_probe(struct platform_device *pdev) } if (of_property_read_u32(pdev->dev.of_node, "tx-fifo-depth", - &priv->rx_fifo_depth)) { + &priv->tx_fifo_depth)) { dev_err(&pdev->dev, "cannot obtain tx-fifo-depth\n"); ret = -ENXIO; goto err_free_netdev; -- cgit v1.2.3-59-g8ed1b From 8d4ac39df09c6f8078af60cd0ddd7b2435728e72 Mon Sep 17 00:00:00 2001 From: Vlastimil Setka Date: Mon, 23 Feb 2015 11:30:29 -0600 Subject: altera_tse: Fixes in NAPI and interrupt handling paths Incorrect NAPI polling caused WARNING at net/core/dev.c net_rx_action. Some stability issues were also seen at high throughput and system load before this patch. This patch contains several changes in altera_tse_main.c: - tse_rx() is fixed to not process more than `limit` frames - tse_poll() is refactored to match NAPI logic - only received frames are counted for return value - removed bogus condition `(rxcomplete >= budget || txcomplete > 0)` - replace by: if (rxcomplete < budget) -> call __napi_complete and enable irq - altera_isr() - replace spin_lock_irqsave() by spin_lock() - we are in isr - use spinlocks just over irq manipulation, not over __napi_schedule - reset IRQ first, then disable and schedule napi This is a cleaned up resubmission from Vlastimil's recent submission. Signed-off-by: Vlastimil Setka Signed-off-by: Roman Pisl Signed-off-by: Vince Bridgers Signed-off-by: David S. Miller --- drivers/net/ethernet/altera/altera_tse_main.c | 45 +++++++++++++-------------- 1 file changed, 22 insertions(+), 23 deletions(-) diff --git a/drivers/net/ethernet/altera/altera_tse_main.c b/drivers/net/ethernet/altera/altera_tse_main.c index f3d784a3463d..6725dc00750b 100644 --- a/drivers/net/ethernet/altera/altera_tse_main.c +++ b/drivers/net/ethernet/altera/altera_tse_main.c @@ -376,7 +376,8 @@ static int tse_rx(struct altera_tse_private *priv, int limit) u16 pktlength; u16 pktstatus; - while ((rxstatus = priv->dmaops->get_rx_status(priv)) != 0) { + while (((rxstatus = priv->dmaops->get_rx_status(priv)) != 0) && + (count < limit)) { pktstatus = rxstatus >> 16; pktlength = rxstatus & 0xffff; @@ -491,28 +492,27 @@ static int tse_poll(struct napi_struct *napi, int budget) struct altera_tse_private *priv = container_of(napi, struct altera_tse_private, napi); int rxcomplete = 0; - int txcomplete = 0; unsigned long int flags; - txcomplete = tse_tx_complete(priv); + tse_tx_complete(priv); rxcomplete = tse_rx(priv, budget); - if (rxcomplete >= budget || txcomplete > 0) - return rxcomplete; + if (rxcomplete < budget) { - napi_gro_flush(napi, false); - __napi_complete(napi); + napi_gro_flush(napi, false); + __napi_complete(napi); - netdev_dbg(priv->dev, - "NAPI Complete, did %d packets with budget %d\n", - txcomplete+rxcomplete, budget); + netdev_dbg(priv->dev, + "NAPI Complete, did %d packets with budget %d\n", + rxcomplete, budget); - spin_lock_irqsave(&priv->rxdma_irq_lock, flags); - priv->dmaops->enable_rxirq(priv); - priv->dmaops->enable_txirq(priv); - spin_unlock_irqrestore(&priv->rxdma_irq_lock, flags); - return rxcomplete + txcomplete; + spin_lock_irqsave(&priv->rxdma_irq_lock, flags); + priv->dmaops->enable_rxirq(priv); + priv->dmaops->enable_txirq(priv); + spin_unlock_irqrestore(&priv->rxdma_irq_lock, flags); + } + return rxcomplete; } /* DMA TX & RX FIFO interrupt routing @@ -521,7 +521,6 @@ static irqreturn_t altera_isr(int irq, void *dev_id) { struct net_device *dev = dev_id; struct altera_tse_private *priv; - unsigned long int flags; if (unlikely(!dev)) { pr_err("%s: invalid dev pointer\n", __func__); @@ -529,20 +528,20 @@ static irqreturn_t altera_isr(int irq, void *dev_id) } priv = netdev_priv(dev); - /* turn off desc irqs and enable napi rx */ - spin_lock_irqsave(&priv->rxdma_irq_lock, flags); + spin_lock(&priv->rxdma_irq_lock); + /* reset IRQs */ + priv->dmaops->clear_rxirq(priv); + priv->dmaops->clear_txirq(priv); + spin_unlock(&priv->rxdma_irq_lock); if (likely(napi_schedule_prep(&priv->napi))) { + spin_lock(&priv->rxdma_irq_lock); priv->dmaops->disable_rxirq(priv); priv->dmaops->disable_txirq(priv); + spin_unlock(&priv->rxdma_irq_lock); __napi_schedule(&priv->napi); } - /* reset IRQs */ - priv->dmaops->clear_rxirq(priv); - priv->dmaops->clear_txirq(priv); - - spin_unlock_irqrestore(&priv->rxdma_irq_lock, flags); return IRQ_HANDLED; } -- cgit v1.2.3-59-g8ed1b From fc921566f4fcf4499e9a6d010391c00be199ab85 Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Tue, 24 Feb 2015 10:12:55 +1100 Subject: xfs: Ensure we have target_ip for RENAME_EXCHANGE We shouldn't get here with RENAME_EXCHANGE set and no target_ip, but let's be defensive, because xfs_cross_rename() will dereference it. Spotted by Coverity. Signed-off-by: Eric Sandeen Reviewed-by: Christoph Hellwig Signed-off-by: Dave Chinner --- fs/xfs/xfs_inode.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index daafa1f6d260..6163767aa856 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -2867,6 +2867,10 @@ xfs_rename( * Handle RENAME_EXCHANGE flags */ if (flags & RENAME_EXCHANGE) { + if (target_ip == NULL) { + error = -EINVAL; + goto error_return; + } error = xfs_cross_rename(tp, src_dp, src_name, src_ip, target_dp, target_name, target_ip, &free_list, &first_block, spaceres); -- cgit v1.2.3-59-g8ed1b From 83d5f01858b56db69c8e4ca5389ef7c29bfdb5dd Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Tue, 24 Feb 2015 10:15:18 +1100 Subject: xfs: cancel failed transaction in xfs_fs_commit_blocks() If xfs_trans_reserve fails we don't cancel the transaction, and we'll leak the allocated transaction pointer. Spotted by Coverity. Signed-off-by: Eric Sandeen Reviewed-by: Christoph Hellwig Signed-off-by: Dave Chinner --- fs/xfs/xfs_pnfs.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/xfs/xfs_pnfs.c b/fs/xfs/xfs_pnfs.c index 4b33ef112400..365dd57ea760 100644 --- a/fs/xfs/xfs_pnfs.c +++ b/fs/xfs/xfs_pnfs.c @@ -300,8 +300,10 @@ xfs_fs_commit_blocks( tp = xfs_trans_alloc(mp, XFS_TRANS_SETATTR_NOT_SIZE); error = xfs_trans_reserve(tp, &M_RES(mp)->tr_ichange, 0, 0); - if (error) + if (error) { + xfs_trans_cancel(tp, 0); goto out_drop_iolock; + } xfs_ilock(ip, XFS_ILOCK_EXCL); xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL); -- cgit v1.2.3-59-g8ed1b From 77751427a1ff25b27d47a4c36b12c3c8667855ac Mon Sep 17 00:00:00 2001 From: Marcelo Leitner Date: Mon, 23 Feb 2015 11:17:13 -0300 Subject: ipv6: addrconf: validate new MTU before applying it Currently we don't check if the new MTU is valid or not and this allows one to configure a smaller than minimum allowed by RFCs or even bigger than interface own MTU, which is a problem as it may lead to packet drops. If you have a daemon like NetworkManager running, this may be exploited by remote attackers by forging RA packets with an invalid MTU, possibly leading to a DoS. (NetworkManager currently only validates for values too small, but not for too big ones.) The fix is just to make sure the new value is valid. That is, between IPV6_MIN_MTU and interface's MTU. Note that similar check is already performed at ndisc_router_discovery(), for when kernel itself parses the RA. Signed-off-by: Marcelo Ricardo Leitner Signed-off-by: Sabrina Dubroca Signed-off-by: David S. Miller --- net/ipv6/addrconf.c | 17 ++++++++++++++++- 1 file changed, 16 insertions(+), 1 deletion(-) diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c index 98e4a63d72bb..b6030025f411 100644 --- a/net/ipv6/addrconf.c +++ b/net/ipv6/addrconf.c @@ -4903,6 +4903,21 @@ int addrconf_sysctl_forward(struct ctl_table *ctl, int write, return ret; } +static +int addrconf_sysctl_mtu(struct ctl_table *ctl, int write, + void __user *buffer, size_t *lenp, loff_t *ppos) +{ + struct inet6_dev *idev = ctl->extra1; + int min_mtu = IPV6_MIN_MTU; + struct ctl_table lctl; + + lctl = *ctl; + lctl.extra1 = &min_mtu; + lctl.extra2 = idev ? &idev->dev->mtu : NULL; + + return proc_dointvec_minmax(&lctl, write, buffer, lenp, ppos); +} + static void dev_disable_change(struct inet6_dev *idev) { struct netdev_notifier_info info; @@ -5054,7 +5069,7 @@ static struct addrconf_sysctl_table .data = &ipv6_devconf.mtu6, .maxlen = sizeof(int), .mode = 0644, - .proc_handler = proc_dointvec, + .proc_handler = addrconf_sysctl_mtu, }, { .procname = "accept_ra", -- cgit v1.2.3-59-g8ed1b From 2caa80e72b57c6216aec6f6a11fcfb4fec46daa0 Mon Sep 17 00:00:00 2001 From: Daniel Vetter Date: Sun, 22 Feb 2015 11:38:36 +0100 Subject: drm: Fix deadlock due to getconnector locking changes In commit ccfc08655d5fd5076828f45fb09194c070f2f63a Author: Rob Clark Date: Thu Dec 18 16:01:48 2014 -0500 drm: tweak getconnector locking We need to extend the locking to cover connector->state reading for atomic drivers, but the above commit was a bit too eager and also included the fill_modes callback. Which on i915 on old platforms using load detection needs to acquire modeset locks, resulting in a deadlock on output probing. Reported-by: Marc Finet Cc: Marc Finet Cc: robdclark@gmail.com Signed-off-by: Daniel Vetter Reviewed-by: Rob Clark Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_crtc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c index 6b00173d1be4..6b6b07ff720b 100644 --- a/drivers/gpu/drm/drm_crtc.c +++ b/drivers/gpu/drm/drm_crtc.c @@ -2127,7 +2127,6 @@ int drm_mode_getconnector(struct drm_device *dev, void *data, DRM_DEBUG_KMS("[CONNECTOR:%d:?]\n", out_resp->connector_id); mutex_lock(&dev->mode_config.mutex); - drm_modeset_lock(&dev->mode_config.connection_mutex, NULL); connector = drm_connector_find(dev, out_resp->connector_id); if (!connector) { @@ -2157,6 +2156,8 @@ int drm_mode_getconnector(struct drm_device *dev, void *data, out_resp->mm_height = connector->display_info.height_mm; out_resp->subpixel = connector->display_info.subpixel_order; out_resp->connection = connector->status; + + drm_modeset_lock(&dev->mode_config.connection_mutex, NULL); encoder = drm_connector_get_encoder(connector); if (encoder) out_resp->encoder_id = encoder->base.id; -- cgit v1.2.3-59-g8ed1b From 579deee571a755c485ad702ef82c77a98a2ccc05 Mon Sep 17 00:00:00 2001 From: Yannick Guerrini Date: Mon, 23 Feb 2015 17:52:38 +0100 Subject: x86/platform/intel-mid: Fix trivial printk message typo in intel_mid_arch_setup() Change 'Uknown' to 'Unknown' Signed-off-by: Yannick Guerrini Cc: trivial@kernel.org Link: http://lkml.kernel.org/r/1424710358-10140-1-git-send-email-yguerrini@tomshardware.fr Signed-off-by: Ingo Molnar --- arch/x86/platform/intel-mid/intel-mid.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/platform/intel-mid/intel-mid.c b/arch/x86/platform/intel-mid/intel-mid.c index 1bbedc4b0f88..3005f0c89f2e 100644 --- a/arch/x86/platform/intel-mid/intel-mid.c +++ b/arch/x86/platform/intel-mid/intel-mid.c @@ -130,7 +130,7 @@ static void intel_mid_arch_setup(void) intel_mid_ops = get_intel_mid_ops[__intel_mid_cpu_chip](); else { intel_mid_ops = get_intel_mid_ops[INTEL_MID_CPU_CHIP_PENWELL](); - pr_info("ARCH: Uknown SoC, assuming PENWELL!\n"); + pr_info("ARCH: Unknown SoC, assuming PENWELL!\n"); } out: -- cgit v1.2.3-59-g8ed1b From 850529249d7cce02e9bfae9476d09c8c51410d28 Mon Sep 17 00:00:00 2001 From: Bard Liao Date: Mon, 16 Feb 2015 13:06:45 +0800 Subject: ASoC: rt5670: Set RT5670_IRQ_CTRL1 non volatile RT5670_IRQ_CTRL1(0xbd) is a non volatile register. And we need to restore its value after suspend/resume. Signed-off-by: Bard Liao Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- sound/soc/codecs/rt5670.c | 1 - 1 file changed, 1 deletion(-) diff --git a/sound/soc/codecs/rt5670.c b/sound/soc/codecs/rt5670.c index d33f33ce865a..b651bc06cfdf 100644 --- a/sound/soc/codecs/rt5670.c +++ b/sound/soc/codecs/rt5670.c @@ -223,7 +223,6 @@ static bool rt5670_volatile_register(struct device *dev, unsigned int reg) case RT5670_ADC_EQ_CTRL1: case RT5670_EQ_CTRL1: case RT5670_ALC_CTRL_1: - case RT5670_IRQ_CTRL1: case RT5670_IRQ_CTRL2: case RT5670_INT_IRQ_ST: case RT5670_IL_CMD: -- cgit v1.2.3-59-g8ed1b From 148388f375394ac1afed543cb653c94be5faa810 Mon Sep 17 00:00:00 2001 From: Thomas Niederprüm Date: Sat, 21 Feb 2015 17:22:38 +0100 Subject: ASoC: sta32x: fix register range in regmap. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The STA32X_AUTO3 is a writable register that currently does not appear in the regmap ranges(neither read nor write). By adding this register to the register ranges there is no gap anymore and the existing register ranges can be joined. This fixes a regression introduced in commit a1be4cead9b9504aa6fc93b624975601cec8c188 where the driver was moved to direct regmap usage and the STA32X_AUTO3 register was missed. That made it impossible to choose the preset EQ mode set through the STA32X_AUTO3 register. Fixes: a1be4cead9 (ASoC: sta32x: Convert to direct regmap API usage) Signed-off-by: Thomas Niederprüm Signed-off-by: Mark Brown --- sound/soc/codecs/sta32x.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/sound/soc/codecs/sta32x.c b/sound/soc/codecs/sta32x.c index 3a1343fa109b..007a0e3bc273 100644 --- a/sound/soc/codecs/sta32x.c +++ b/sound/soc/codecs/sta32x.c @@ -106,13 +106,11 @@ static const struct reg_default sta32x_regs[] = { }; static const struct regmap_range sta32x_write_regs_range[] = { - regmap_reg_range(STA32X_CONFA, STA32X_AUTO2), - regmap_reg_range(STA32X_C1CFG, STA32X_FDRC2), + regmap_reg_range(STA32X_CONFA, STA32X_FDRC2), }; static const struct regmap_range sta32x_read_regs_range[] = { - regmap_reg_range(STA32X_CONFA, STA32X_AUTO2), - regmap_reg_range(STA32X_C1CFG, STA32X_FDRC2), + regmap_reg_range(STA32X_CONFA, STA32X_FDRC2), }; static const struct regmap_range sta32x_volatile_regs_range[] = { -- cgit v1.2.3-59-g8ed1b From f2831e2007810b690f93a26128058a193eadf393 Mon Sep 17 00:00:00 2001 From: Bob Copeland Date: Thu, 5 Feb 2015 08:45:43 -0500 Subject: mac80211_hwsim: fix error handling in tx_frame_nl Correct two problems with the error handling when using the netlink forwarding API: first, the netlink skb is never freed if nla_put() fails; and second, genlmsg_unicast() can fail if the netlink socket is full. In the latter case, the corresponding data skb is not counted as a drop and userspace programs like wmediumd will see TCP stalls due to lost packets. Signed-off-by: Bob Copeland Signed-off-by: Johannes Berg --- drivers/net/wireless/mac80211_hwsim.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c index 4a4c6586a8d2..8908be6dbc48 100644 --- a/drivers/net/wireless/mac80211_hwsim.c +++ b/drivers/net/wireless/mac80211_hwsim.c @@ -946,7 +946,8 @@ static void mac80211_hwsim_tx_frame_nl(struct ieee80211_hw *hw, goto nla_put_failure; genlmsg_end(skb, msg_head); - genlmsg_unicast(&init_net, skb, dst_portid); + if (genlmsg_unicast(&init_net, skb, dst_portid)) + goto err_free_txskb; /* Enqueue the packet */ skb_queue_tail(&data->pending, my_skb); @@ -955,6 +956,8 @@ static void mac80211_hwsim_tx_frame_nl(struct ieee80211_hw *hw, return; nla_put_failure: + nlmsg_free(skb); +err_free_txskb: printk(KERN_DEBUG "mac80211_hwsim: error occurred in %s\n", __func__); ieee80211_free_txskb(hw, my_skb); data->tx_failed++; -- cgit v1.2.3-59-g8ed1b From 104f5a6206f4b3133c675e3d41eca2ca4c41406b Mon Sep 17 00:00:00 2001 From: Eliad Peller Date: Sun, 8 Feb 2015 12:36:07 +0200 Subject: mac80211: clear sdata->radar_required If ieee80211_vif_use_channel() fails, we have to clear sdata->radar_required (which we might have just set). Failing to do it results in stale radar_required field which prevents starting new scan requests. Reported-by: Jouni Malinen Signed-off-by: Eliad Peller [use false instead of 0] Signed-off-by: Johannes Berg --- net/mac80211/chan.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/net/mac80211/chan.c b/net/mac80211/chan.c index ff0d2db09df9..5bcd4e5589d3 100644 --- a/net/mac80211/chan.c +++ b/net/mac80211/chan.c @@ -1508,6 +1508,8 @@ static void __ieee80211_vif_release_channel(struct ieee80211_sub_if_data *sdata) if (ieee80211_chanctx_refcount(local, ctx) == 0) ieee80211_free_chanctx(local, ctx); + sdata->radar_required = false; + /* Unreserving may ready an in-place reservation. */ if (use_reserved_switch) ieee80211_vif_use_reserved_switch(local); @@ -1566,6 +1568,9 @@ int ieee80211_vif_use_channel(struct ieee80211_sub_if_data *sdata, ieee80211_recalc_smps_chanctx(local, ctx); ieee80211_recalc_radar_chanctx(local, ctx); out: + if (ret) + sdata->radar_required = false; + mutex_unlock(&local->chanctx_mtx); return ret; } -- cgit v1.2.3-59-g8ed1b From 5528fae88697268a7176dd6c8d7ab368c04368be Mon Sep 17 00:00:00 2001 From: Samuel Tan Date: Mon, 9 Feb 2015 21:29:15 +0200 Subject: nl80211: use loop index as type for net detect frequency results We currently add nested members of the NL80211_ATTR_SCAN_FREQUENCIES as NLA_U32 attributes of type NL80211_ATTR_WIPHY_FREQ in cfg80211_net_detect_results. However, since there can be an arbitrary number of frequency results, we should use the loop index of the loop used to add the frequency results to NL80211_ATTR_SCAN_FREQUENCIES as the type (i.e. nla_type) for each result attribute, rather than a fixed type. This change is in line with how nested members are added to NL80211_ATTR_SCAN_FREQUENCIES in the functions nl80211_send_wowlan_nd and nl80211_add_scan_req. Signed-off-by: Samuel Tan Signed-off-by: Luciano Coelho Signed-off-by: Johannes Berg --- net/wireless/nl80211.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index d78fd8b54515..3c7fb0459e58 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -12528,9 +12528,7 @@ static int cfg80211_net_detect_results(struct sk_buff *msg, } for (j = 0; j < match->n_channels; j++) { - if (nla_put_u32(msg, - NL80211_ATTR_WIPHY_FREQ, - match->channels[j])) { + if (nla_put_u32(msg, j, match->channels[j])) { nla_nest_cancel(msg, nl_freqs); nla_nest_cancel(msg, nl_match); goto out; -- cgit v1.2.3-59-g8ed1b From a18c7192aabac73078f35e5ef4ce28ad5f8cfe8e Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Tue, 24 Feb 2015 10:56:42 +0100 Subject: nl80211: fix memory leak in monitor flags parsing If monitor flags parsing results in active monitor but that isn't supported, the already allocated message is leaked. Fix this by moving the allocation after this check. Reported-by: Christian Engelmayer Signed-off-by: Johannes Berg --- net/wireless/nl80211.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index 3c7fb0459e58..be2501538011 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -2654,10 +2654,6 @@ static int nl80211_new_interface(struct sk_buff *skb, struct genl_info *info) return err; } - msg = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_KERNEL); - if (!msg) - return -ENOMEM; - err = parse_monitor_flags(type == NL80211_IFTYPE_MONITOR ? info->attrs[NL80211_ATTR_MNTR_FLAGS] : NULL, &flags); @@ -2666,6 +2662,10 @@ static int nl80211_new_interface(struct sk_buff *skb, struct genl_info *info) !(rdev->wiphy.features & NL80211_FEATURE_ACTIVE_MONITOR)) return -EOPNOTSUPP; + msg = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_KERNEL); + if (!msg) + return -ENOMEM; + wdev = rdev_add_virtual_intf(rdev, nla_data(info->attrs[NL80211_ATTR_IFNAME]), type, err ? NULL : &flags, ¶ms); -- cgit v1.2.3-59-g8ed1b From 28981e5eb45fe13e1d2c9e0e2e189dc5c8682006 Mon Sep 17 00:00:00 2001 From: Jason Abele Date: Tue, 17 Feb 2015 16:10:41 -0800 Subject: cfg80211: fix n_reg_rules to match world_regdom There are currently 8 rules in the world_regdom, but only the first 6 are applied due to an incorrect value for n_reg_rules. This causes channels 149-165 and 60GHz to be disabled. Signed-off-by: Jason Abele Signed-off-by: Johannes Berg --- net/wireless/reg.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/wireless/reg.c b/net/wireless/reg.c index b586d0dcb09e..48dfc7b4e981 100644 --- a/net/wireless/reg.c +++ b/net/wireless/reg.c @@ -228,7 +228,7 @@ static DECLARE_DELAYED_WORK(reg_timeout, reg_timeout_work); /* We keep a static world regulatory domain in case of the absence of CRDA */ static const struct ieee80211_regdomain world_regdom = { - .n_reg_rules = 6, + .n_reg_rules = 8, .alpha2 = "00", .reg_rules = { /* IEEE 802.11b/g, channels 1..11 */ -- cgit v1.2.3-59-g8ed1b From 81daf735f9fe35ef6bc4073068748b221d64fb47 Mon Sep 17 00:00:00 2001 From: Junjie Mao Date: Wed, 28 Jan 2015 10:03:26 +0800 Subject: cfg80211: calls nl80211_exit on error nl80211_exit should be called in cfg80211_init if nl80211_init succeeds but regulatory_init or create_singlethread_workqueue fails. Signed-off-by: Junjie Mao Signed-off-by: Johannes Berg --- net/wireless/core.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/wireless/core.c b/net/wireless/core.c index 3af0ecf1cc16..2a0bbd22854b 100644 --- a/net/wireless/core.c +++ b/net/wireless/core.c @@ -1199,6 +1199,7 @@ out_fail_wq: regulatory_exit(); out_fail_reg: debugfs_remove(ieee80211_debugfs_dir); + nl80211_exit(); out_fail_nl80211: unregister_netdevice_notifier(&cfg80211_netdev_notifier); out_fail_notifier: -- cgit v1.2.3-59-g8ed1b From bd4248bb5e8b41f88a2789ee124dce3e9ec4f227 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Fri, 6 Feb 2015 16:04:08 +0100 Subject: drm: atmel-hlcdc: reset layer A2Q and UPDATE bits when disabling it The A2Q (Add To Queue) and UPDATE bits are left in their previous state when resetting the layer. This lead to weird behavior when enabling the plane again: the framebuffer previously queued is dequeued and we end up with access to an old memory region. Reset those bits when resetting the channel. Signed-off-by: Boris Brezillon --- drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.c index 063d2a7b941f..e79bd9ba474b 100644 --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.c +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.c @@ -311,7 +311,8 @@ int atmel_hlcdc_layer_disable(struct atmel_hlcdc_layer *layer) /* Disable the layer */ regmap_write(regmap, desc->regs_offset + ATMEL_HLCDC_LAYER_CHDR, - ATMEL_HLCDC_LAYER_RST); + ATMEL_HLCDC_LAYER_RST | ATMEL_HLCDC_LAYER_A2Q | + ATMEL_HLCDC_LAYER_UPDATE); /* Clear all pending interrupts */ regmap_read(regmap, desc->regs_offset + ATMEL_HLCDC_LAYER_ISR, &isr); -- cgit v1.2.3-59-g8ed1b From 0f2cfa81161359a7be255f7bd5aec2ff3460a5c9 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Tue, 10 Feb 2015 16:23:00 +0100 Subject: drm: atmel-hlcdc: remove useless pm_runtime_put_sync in probe Remove a useless pm_runtime_put_sync leading to unbalanced usage_count. Signed-off-by: Boris Brezillon Reported-by: Sylvain Rochet --- drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.c index 7320a6c6613f..c1cb17493e0d 100644 --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.c +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.c @@ -311,8 +311,6 @@ static int atmel_hlcdc_dc_load(struct drm_device *dev) pm_runtime_enable(dev->dev); - pm_runtime_put_sync(dev->dev); - ret = atmel_hlcdc_dc_modeset_init(dev); if (ret < 0) { dev_err(dev->dev, "failed to initialize mode setting\n"); -- cgit v1.2.3-59-g8ed1b From c2996cb29bfb73927a79dc96e598a718e843f01a Mon Sep 17 00:00:00 2001 From: James Hogan Date: Tue, 24 Feb 2015 12:25:25 +0000 Subject: metag: Fix KSTK_EIP() and KSTK_ESP() macros The KSTK_EIP() and KSTK_ESP() macros should return the user program counter (PC) and stack pointer (A0StP) of the given task. These are used to determine which VMA corresponds to the user stack in /proc//maps, and for the user PC & A0StP in /proc//stat. However for Meta the PC & A0StP from the task's kernel context are used, resulting in broken output. For example in following /proc//maps output, the 3afff000-3b021000 VMA should be described as the stack: # cat /proc/self/maps ... 100b0000-100b1000 rwxp 00000000 00:00 0 [heap] 3afff000-3b021000 rwxp 00000000 00:00 0 And in the following /proc//stat output, the PC is in kernel code (1074234964 = 0x40078654) and the A0StP is in the kernel heap (1335981392 = 0x4fa17550): # cat /proc/self/stat 51 (cat) R ... 1335981392 1074234964 ... Fix the definitions of KSTK_EIP() and KSTK_ESP() to use task_pt_regs(tsk)->ctx rather than (tsk)->thread.kernel_context. This gets the registers from the user context stored after the thread info at the base of the kernel stack, which is from the last entry into the kernel from userland, regardless of where in the kernel the task may have been interrupted, which results in the following more correct /proc//maps output: # cat /proc/self/maps ... 0800b000-08070000 r-xp 00000000 00:02 207 /lib/libuClibc-0.9.34-git.so ... 100b0000-100b1000 rwxp 00000000 00:00 0 [heap] 3afff000-3b021000 rwxp 00000000 00:00 0 [stack] And /proc//stat now correctly reports the PC in libuClibc (134320308 = 0x80190b4) and the A0StP in the [stack] region (989864576 = 0x3b002280): # cat /proc/self/stat 51 (cat) R ... 989864576 134320308 ... Reported-by: Alexey Brodkin Reported-by: Vineet Gupta Signed-off-by: James Hogan Cc: linux-metag@vger.kernel.org Cc: # v3.9+ --- arch/metag/include/asm/processor.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/metag/include/asm/processor.h b/arch/metag/include/asm/processor.h index 881071c07942..13272fd5a5ba 100644 --- a/arch/metag/include/asm/processor.h +++ b/arch/metag/include/asm/processor.h @@ -149,8 +149,8 @@ extern void exit_thread(void); unsigned long get_wchan(struct task_struct *p); -#define KSTK_EIP(tsk) ((tsk)->thread.kernel_context->CurrPC) -#define KSTK_ESP(tsk) ((tsk)->thread.kernel_context->AX[0].U0) +#define KSTK_EIP(tsk) (task_pt_regs(tsk)->ctx.CurrPC) +#define KSTK_ESP(tsk) (task_pt_regs(tsk)->ctx.AX[0].U0) #define user_stack_pointer(regs) ((regs)->ctx.AX[0].U0) -- cgit v1.2.3-59-g8ed1b From 37ed398839fa3e0d2de77925097db7a370abb096 Mon Sep 17 00:00:00 2001 From: Jaroslav Kysela Date: Tue, 24 Feb 2015 12:04:57 +0100 Subject: ALSA: hda: controller code - do not export static functions It is a bad idea to export static functions. GCC for some platforms shows errors like: error: __ksymtab_azx_get_response causes a section type conflict Signed-off-by: Jaroslav Kysela Cc: # v3.15+ Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_controller.c | 5 ----- 1 file changed, 5 deletions(-) diff --git a/sound/pci/hda/hda_controller.c b/sound/pci/hda/hda_controller.c index dfcb5e929f9f..a2ce773bdc62 100644 --- a/sound/pci/hda/hda_controller.c +++ b/sound/pci/hda/hda_controller.c @@ -961,7 +961,6 @@ static int azx_alloc_cmd_io(struct azx *chip) dev_err(chip->card->dev, "cannot allocate CORB/RIRB\n"); return err; } -EXPORT_SYMBOL_GPL(azx_alloc_cmd_io); static void azx_init_cmd_io(struct azx *chip) { @@ -1026,7 +1025,6 @@ static void azx_init_cmd_io(struct azx *chip) azx_writeb(chip, RIRBCTL, AZX_RBCTL_DMA_EN | AZX_RBCTL_IRQ_EN); spin_unlock_irq(&chip->reg_lock); } -EXPORT_SYMBOL_GPL(azx_init_cmd_io); static void azx_free_cmd_io(struct azx *chip) { @@ -1036,7 +1034,6 @@ static void azx_free_cmd_io(struct azx *chip) azx_writeb(chip, CORBCTL, 0); spin_unlock_irq(&chip->reg_lock); } -EXPORT_SYMBOL_GPL(azx_free_cmd_io); static unsigned int azx_command_addr(u32 cmd) { @@ -1316,7 +1313,6 @@ static int azx_send_cmd(struct hda_bus *bus, unsigned int val) else return azx_corb_send_cmd(bus, val); } -EXPORT_SYMBOL_GPL(azx_send_cmd); /* get a response */ static unsigned int azx_get_response(struct hda_bus *bus, @@ -1330,7 +1326,6 @@ static unsigned int azx_get_response(struct hda_bus *bus, else return azx_rirb_get_response(bus, addr); } -EXPORT_SYMBOL_GPL(azx_get_response); #ifdef CONFIG_SND_HDA_DSP_LOADER /* -- cgit v1.2.3-59-g8ed1b From b3a38998f042b862f5ba4d7f2268f3a8dfb4883a Mon Sep 17 00:00:00 2001 From: Nick Hoath Date: Thu, 19 Feb 2015 16:30:47 +0000 Subject: drm/i915: Fix a use after free, and unbalanced refcounting When converting from implicitly tracked execlist queue items to ref counted requests, not all frees of requests were replaced with unrefs, and extraneous refs/unrefs of contexts were added. Correct the unbalanced refcount & replace the frees. Remove a noisy warning when hitting the request creation path. drm_i915_gem_request and intel_context are both kref reference counted structures. Upon allocation, drm_i915_gem_request's ref count should be bumped using kref_init. When a context is assigned to the request, the context's reference count should be bumped using i915_gem_context_reference. i915_gem_request_reference will reduce the context reference count when the request is freed. Problem introduced in commit 6d3d8274bc45de4babb62d64562d92af984dd238 Author: Nick Hoath AuthorDate: Thu Jan 15 13:10:39 2015 +0000 drm/i915: Subsume intel_ctx_submit_request in to drm_i915_gem_request v2: Added comments explaining how the ctx pointer and the request object should be ref-counted. Removed noisy warning. v3: Cleaned up the language used in the commit & the header description (Thanks David Gordon) Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88652 Signed-off-by: Nick Hoath Reviewed-by: Thomas Daniel Reviewed-by: Daniel Vetter Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/i915_drv.h | 14 +++++++++++++- drivers/gpu/drm/i915/i915_gem.c | 3 +-- drivers/gpu/drm/i915/intel_lrc.c | 8 ++++---- 3 files changed, 18 insertions(+), 7 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index b38c770a22f5..8727086cf48c 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -2114,6 +2114,9 @@ void i915_gem_track_fb(struct drm_i915_gem_object *old, * number comparisons on buffer last_read|write_seqno. It also allows an * emission time to be associated with the request for tracking how far ahead * of the GPU the submission is. + * + * The requests are reference counted, so upon creation they should have an + * initial reference taken using kref_init */ struct drm_i915_gem_request { struct kref ref; @@ -2137,7 +2140,16 @@ struct drm_i915_gem_request { /** Position in the ringbuffer of the end of the whole request */ u32 tail; - /** Context related to this request */ + /** + * Context related to this request + * Contexts are refcounted, so when this request is associated with a + * context, we must increment the context's refcount, to guarantee that + * it persists while any request is linked to it. Requests themselves + * are also refcounted, so the request will only be freed when the last + * reference to it is dismissed, and the code in + * i915_gem_request_free() will then decrement the refcount on the + * context. + */ struct intel_context *ctx; /** Batch buffer related to this request if any */ diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c index c26d36cc4b31..e5daad5f75fb 100644 --- a/drivers/gpu/drm/i915/i915_gem.c +++ b/drivers/gpu/drm/i915/i915_gem.c @@ -2659,8 +2659,7 @@ static void i915_gem_reset_ring_cleanup(struct drm_i915_private *dev_priv, if (submit_req->ctx != ring->default_context) intel_lr_context_unpin(ring, submit_req->ctx); - i915_gem_context_unreference(submit_req->ctx); - kfree(submit_req); + i915_gem_request_unreference(submit_req); } /* diff --git a/drivers/gpu/drm/i915/intel_lrc.c b/drivers/gpu/drm/i915/intel_lrc.c index 0f358c5999ec..e8d3da9f3373 100644 --- a/drivers/gpu/drm/i915/intel_lrc.c +++ b/drivers/gpu/drm/i915/intel_lrc.c @@ -503,18 +503,19 @@ static int execlists_context_queue(struct intel_engine_cs *ring, * If there isn't a request associated with this submission, * create one as a temporary holder. */ - WARN(1, "execlist context submission without request"); request = kzalloc(sizeof(*request), GFP_KERNEL); if (request == NULL) return -ENOMEM; request->ring = ring; request->ctx = to; + kref_init(&request->ref); + request->uniq = dev_priv->request_uniq++; + i915_gem_context_reference(request->ctx); } else { + i915_gem_request_reference(request); WARN_ON(to != request->ctx); } request->tail = tail; - i915_gem_request_reference(request); - i915_gem_context_reference(request->ctx); intel_runtime_pm_get(dev_priv); @@ -731,7 +732,6 @@ void intel_execlists_retire_requests(struct intel_engine_cs *ring) if (ctx_obj && (ctx != ring->default_context)) intel_lr_context_unpin(ring, ctx); intel_runtime_pm_put(dev_priv); - i915_gem_context_unreference(ctx); list_del(&req->execlist_link); i915_gem_request_unreference(req); } -- cgit v1.2.3-59-g8ed1b From 6c31a614c43ae274546f736b2a33363e149c3dc2 Mon Sep 17 00:00:00 2001 From: Chris Wilson Date: Thu, 12 Feb 2015 07:53:18 +0000 Subject: drm/i915: Check obj->vma_list under the struct_mutex When we walk the list of vma, or even for protecting against concurrent framebuffer creation, we must hold the struct_mutex or else a second thread can corrupt the list as we walk it. Fixes regression from commit d7f46fc4e7323887494db13f063a8e59861fefb0 Author: Ben Widawsky Date: Fri Dec 6 14:10:55 2013 -0800 drm/i915: Make pin count per VMA References: https://bugs.freedesktop.org/show_bug.cgi?id=89085 Signed-off-by: Chris Wilson Reviewed-by: Daniel Vetter Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/i915_gem_tiling.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_gem_tiling.c b/drivers/gpu/drm/i915/i915_gem_tiling.c index 7a24bd1a51f6..6377b22269ad 100644 --- a/drivers/gpu/drm/i915/i915_gem_tiling.c +++ b/drivers/gpu/drm/i915/i915_gem_tiling.c @@ -335,9 +335,10 @@ i915_gem_set_tiling(struct drm_device *dev, void *data, return -EINVAL; } + mutex_lock(&dev->struct_mutex); if (i915_gem_obj_is_pinned(obj) || obj->framebuffer_references) { - drm_gem_object_unreference_unlocked(&obj->base); - return -EBUSY; + ret = -EBUSY; + goto err; } if (args->tiling_mode == I915_TILING_NONE) { @@ -369,7 +370,6 @@ i915_gem_set_tiling(struct drm_device *dev, void *data, } } - mutex_lock(&dev->struct_mutex); if (args->tiling_mode != obj->tiling_mode || args->stride != obj->stride) { /* We need to rebind the object if its current allocation @@ -424,6 +424,7 @@ i915_gem_set_tiling(struct drm_device *dev, void *data, obj->bit_17 = NULL; } +err: drm_gem_object_unreference(&obj->base); mutex_unlock(&dev->struct_mutex); -- cgit v1.2.3-59-g8ed1b From 2dd2a883aad7c852400027c2261bcab69d9e238e Mon Sep 17 00:00:00 2001 From: Imre Deak Date: Tue, 24 Feb 2015 11:14:30 +0200 Subject: drm/i915: avoid processing spurious/shared interrupts in low-power states Atm, it's possible that the interrupt handler is called when the device is in D3 or some other low-power state. It can be due to another device that is still in D0 state and shares the interrupt line with i915, or on some platforms there could be spurious interrupts even without sharing the interrupt line. The latter case was reported by Klaus Ethgen using a Lenovo x61p machine (gen 4). He noticed this issue via a system suspend/resume hang and bisected it to the following commit: commit e11aa362308f5de467ce355a2a2471321b15a35c Author: Jesse Barnes Date: Wed Jun 18 09:52:55 2014 -0700 drm/i915: use runtime irq suspend/resume in freeze/thaw This is a problem, since in low-power states IIR will always read 0xffffffff resulting in an endless IRQ servicing loop. Fix this by handling interrupts only when the driver explicitly enables them and so it's guaranteed that the interrupt registers return a valid value. Note that this issue existed even before the above commit, since during runtime suspend/resume we never unregistered the handler. v2: - clarify the purpose of smp_mb() vs. synchronize_irq() in the code comment (Chris) v3: - no need for an explicit smp_mb(), we can assume that synchronize_irq() and the mmio read/writes in the install hooks provide for this (Daniel) - remove code comment as the remaining synchronize_irq() is self explanatory (Daniel) v4: - drm_irq_uninstall() implies synchronize_irq(), so no need to call it explicitly (Daniel) Reference: https://lkml.org/lkml/2015/2/11/205 Reported-and-bisected-by: Klaus Ethgen Cc: stable@vger.kernel.org Signed-off-by: Imre Deak Reviewed-by: Daniel Vetter Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/i915_irq.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index 4145d95902f5..ede5bbbd8a08 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -1892,6 +1892,9 @@ static irqreturn_t valleyview_irq_handler(int irq, void *arg) u32 iir, gt_iir, pm_iir; irqreturn_t ret = IRQ_NONE; + if (!intel_irqs_enabled(dev_priv)) + return IRQ_NONE; + while (true) { /* Find, clear, then process each source of interrupt */ @@ -1936,6 +1939,9 @@ static irqreturn_t cherryview_irq_handler(int irq, void *arg) u32 master_ctl, iir; irqreturn_t ret = IRQ_NONE; + if (!intel_irqs_enabled(dev_priv)) + return IRQ_NONE; + for (;;) { master_ctl = I915_READ(GEN8_MASTER_IRQ) & ~GEN8_MASTER_IRQ_CONTROL; iir = I915_READ(VLV_IIR); @@ -2208,6 +2214,9 @@ static irqreturn_t ironlake_irq_handler(int irq, void *arg) u32 de_iir, gt_iir, de_ier, sde_ier = 0; irqreturn_t ret = IRQ_NONE; + if (!intel_irqs_enabled(dev_priv)) + return IRQ_NONE; + /* We get interrupts on unclaimed registers, so check for this before we * do any I915_{READ,WRITE}. */ intel_uncore_check_errors(dev); @@ -2279,6 +2288,9 @@ static irqreturn_t gen8_irq_handler(int irq, void *arg) enum pipe pipe; u32 aux_mask = GEN8_AUX_CHANNEL_A; + if (!intel_irqs_enabled(dev_priv)) + return IRQ_NONE; + if (IS_GEN9(dev)) aux_mask |= GEN9_AUX_CHANNEL_B | GEN9_AUX_CHANNEL_C | GEN9_AUX_CHANNEL_D; @@ -3771,6 +3783,9 @@ static irqreturn_t i8xx_irq_handler(int irq, void *arg) I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT | I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT; + if (!intel_irqs_enabled(dev_priv)) + return IRQ_NONE; + iir = I915_READ16(IIR); if (iir == 0) return IRQ_NONE; @@ -3951,6 +3966,9 @@ static irqreturn_t i915_irq_handler(int irq, void *arg) I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT; int pipe, ret = IRQ_NONE; + if (!intel_irqs_enabled(dev_priv)) + return IRQ_NONE; + iir = I915_READ(IIR); do { bool irq_received = (iir & ~flip_mask) != 0; @@ -4171,6 +4189,9 @@ static irqreturn_t i965_irq_handler(int irq, void *arg) I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT | I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT; + if (!intel_irqs_enabled(dev_priv)) + return IRQ_NONE; + iir = I915_READ(IIR); for (;;) { @@ -4520,6 +4541,7 @@ void intel_runtime_pm_disable_interrupts(struct drm_i915_private *dev_priv) { dev_priv->dev->driver->irq_uninstall(dev_priv->dev); dev_priv->pm.irqs_enabled = false; + synchronize_irq(dev_priv->dev->irq); } /** -- cgit v1.2.3-59-g8ed1b From f37b5c2be8979993efee2da50b51126e3908eb8b Mon Sep 17 00:00:00 2001 From: Daniel Vetter Date: Tue, 10 Feb 2015 23:12:27 +0100 Subject: drm/i915: Align initial plane backing objects correctly Some bios really like to joke and start the planes at an offset ... hooray! Align start and end to fix this. v2: Fixup calculation of size, spotted by Chris Wilson. v3: Fix serious fumble I've just spotted. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86883 Cc: stable@vger.kernel.org Cc: Johannes W Cc: Chris Wilson Cc: Jani Nikula Reported-and-tested-by: Johannes W Signed-off-by: Daniel Vetter [Jani: split WARN_ONs, rebase on v4.0-rc1] Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/i915_gem_stolen.c | 6 ++---- drivers/gpu/drm/i915/intel_display.c | 18 ++++++++++++------ 2 files changed, 14 insertions(+), 10 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_gem_stolen.c b/drivers/gpu/drm/i915/i915_gem_stolen.c index a2045848bd1a..9c6f93ec886b 100644 --- a/drivers/gpu/drm/i915/i915_gem_stolen.c +++ b/drivers/gpu/drm/i915/i915_gem_stolen.c @@ -485,10 +485,8 @@ i915_gem_object_create_stolen_for_preallocated(struct drm_device *dev, stolen_offset, gtt_offset, size); /* KISS and expect everything to be page-aligned */ - BUG_ON(stolen_offset & 4095); - BUG_ON(size & 4095); - - if (WARN_ON(size == 0)) + if (WARN_ON(size == 0) || WARN_ON(size & 4095) || + WARN_ON(stolen_offset & 4095)) return NULL; stolen = kzalloc(sizeof(*stolen), GFP_KERNEL); diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 2adedee7e52a..bf19a5cce4a8 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -2371,13 +2371,19 @@ intel_alloc_plane_obj(struct intel_crtc *crtc, struct drm_device *dev = crtc->base.dev; struct drm_i915_gem_object *obj = NULL; struct drm_mode_fb_cmd2 mode_cmd = { 0 }; - u32 base = plane_config->base; + u32 base_aligned = round_down(plane_config->base, PAGE_SIZE); + u32 size_aligned = round_up(plane_config->base + plane_config->size, + PAGE_SIZE); + + size_aligned -= base_aligned; if (plane_config->size == 0) return false; - obj = i915_gem_object_create_stolen_for_preallocated(dev, base, base, - plane_config->size); + obj = i915_gem_object_create_stolen_for_preallocated(dev, + base_aligned, + base_aligned, + size_aligned); if (!obj) return false; @@ -6636,7 +6642,7 @@ i9xx_get_initial_plane_config(struct intel_crtc *crtc, aligned_height = intel_fb_align_height(dev, fb->height, plane_config->tiling); - plane_config->size = PAGE_ALIGN(fb->pitches[0] * aligned_height); + plane_config->size = fb->pitches[0] * aligned_height; DRM_DEBUG_KMS("pipe/plane %c/%d with fb: size=%dx%d@%d, offset=%x, pitch %d, size 0x%x\n", pipe_name(pipe), plane, fb->width, fb->height, @@ -7673,7 +7679,7 @@ skylake_get_initial_plane_config(struct intel_crtc *crtc, aligned_height = intel_fb_align_height(dev, fb->height, plane_config->tiling); - plane_config->size = ALIGN(fb->pitches[0] * aligned_height, PAGE_SIZE); + plane_config->size = fb->pitches[0] * aligned_height; DRM_DEBUG_KMS("pipe %c with fb: size=%dx%d@%d, offset=%x, pitch %d, size 0x%x\n", pipe_name(pipe), fb->width, fb->height, @@ -7764,7 +7770,7 @@ ironlake_get_initial_plane_config(struct intel_crtc *crtc, aligned_height = intel_fb_align_height(dev, fb->height, plane_config->tiling); - plane_config->size = PAGE_ALIGN(fb->pitches[0] * aligned_height); + plane_config->size = fb->pitches[0] * aligned_height; DRM_DEBUG_KMS("pipe %c with fb: size=%dx%d@%d, offset=%x, pitch %d, size 0x%x\n", pipe_name(pipe), fb->width, fb->height, -- cgit v1.2.3-59-g8ed1b From 773c5a0fca5b08af7cce87785e4a99b4c1ac36bf Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 13 Jan 2015 14:23:21 +0200 Subject: ARM: dts: DRA7: Fix SATA PHY node The sata_ref_clk is a reference clock to the SATA phy. This fixes SATA malfunction across suspend/resume or when SATA driver is used as a module. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 5827fedafd43..853d37d96007 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -1090,8 +1090,8 @@ <0x4A096800 0x40>; /* pll_ctrl */ reg-names = "phy_rx", "phy_tx", "pll_ctrl"; ctrl-module = <&omap_control_sata>; - clocks = <&sys_clkin1>; - clock-names = "sysclk"; + clocks = <&sys_clkin1>, <&sata_ref_clk>; + clock-names = "sysclk", "refclk"; #phy-cells = <0>; }; -- cgit v1.2.3-59-g8ed1b From a0182724abd82ad90e0312db0da60a2f2d0442f1 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 13 Jan 2015 14:23:22 +0200 Subject: ARM: dts: OMAP5: Fix SATA PHY node The sata_ref_clk is a reference clock to the SATA phy. This fixes SATA malfunction across suspend/resume or when SATA driver is used as a module. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index b321fdf42c9f..bb498e7cc0f1 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -929,8 +929,8 @@ <0x4A096800 0x40>; /* pll_ctrl */ reg-names = "phy_rx", "phy_tx", "pll_ctrl"; ctrl-module = <&omap_control_sata>; - clocks = <&sys_clkin>; - clock-names = "sysclk"; + clocks = <&sys_clkin>, <&sata_ref_clk>; + clock-names = "sysclk", "refclk"; #phy-cells = <0>; }; }; -- cgit v1.2.3-59-g8ed1b From 1e7e4fb66489cc84366656ca5318f1cb61afd4ba Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Tue, 24 Feb 2015 18:27:00 +0200 Subject: usb: XHCI: platform: Move the Marvell quirks after the enabling the clocks The commit 973747928514 ("usb: host: xhci-plat: add support for the Armada 375/38x XHCI controllers") extended the xhci-plat driver to support the Armada 375/38x SoCs, mostly by adding a quirk configuring the MBUS window. However, that quirk was run before the clock the controllers needs has been enabled. This usually worked because the clock was first enabled by the bootloader, and left as such until the driver is probe, where it tries to access the MBUS configuration registers before enabling the clock. Things get messy when EPROBE_DEFER is involved during the probe, since as part of its error path, the driver will rightfully disable the clock. When the driver will be reprobed, it will retry to access the MBUS registers, but this time with the clock disabled, which hangs forever. Fix this by running the quirks after the clock has been enabled by the driver. Signed-off-by: Maxime Ripard Cc: # v3.16+ Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-plat.c | 19 +++++++++---------- 1 file changed, 9 insertions(+), 10 deletions(-) diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c index 08d402b15482..0e11d61408ff 100644 --- a/drivers/usb/host/xhci-plat.c +++ b/drivers/usb/host/xhci-plat.c @@ -83,16 +83,6 @@ static int xhci_plat_probe(struct platform_device *pdev) if (irq < 0) return -ENODEV; - - if (of_device_is_compatible(pdev->dev.of_node, - "marvell,armada-375-xhci") || - of_device_is_compatible(pdev->dev.of_node, - "marvell,armada-380-xhci")) { - ret = xhci_mvebu_mbus_init_quirk(pdev); - if (ret) - return ret; - } - /* Initialize dma_mask and coherent_dma_mask to 32-bits */ ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)); if (ret) @@ -127,6 +117,15 @@ static int xhci_plat_probe(struct platform_device *pdev) goto put_hcd; } + if (of_device_is_compatible(pdev->dev.of_node, + "marvell,armada-375-xhci") || + of_device_is_compatible(pdev->dev.of_node, + "marvell,armada-380-xhci")) { + ret = xhci_mvebu_mbus_init_quirk(pdev); + if (ret) + goto disable_clk; + } + ret = usb_add_hcd(hcd, irq, IRQF_SHARED); if (ret) goto disable_clk; -- cgit v1.2.3-59-g8ed1b From 6596a926b0b6c80b730a1dd2fa91908e0a539c37 Mon Sep 17 00:00:00 2001 From: Mathias Nyman Date: Tue, 24 Feb 2015 18:27:01 +0200 Subject: xhci: Allocate correct amount of scratchpad buffers Include the high order bit fields for Max scratchpad buffers when calculating how many scratchpad buffers are needed. I'm suprised this hasn't caused more issues, we never allocated more than 32 buffers even if xhci needed more. Either we got lucky and xhci never really used past that area, or then we got enough zeroed dma memory anyway. Should be backported as far back as possible Reported-by: Tim Chen Tested-by: Tim Chen Signed-off-by: Mathias Nyman Cc: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci.h | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 974514762a14..68956b13b8d1 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -88,9 +88,10 @@ struct xhci_cap_regs { #define HCS_IST(p) (((p) >> 0) & 0xf) /* bits 4:7, max number of Event Ring segments */ #define HCS_ERST_MAX(p) (((p) >> 4) & 0xf) +/* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */ /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */ -/* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */ -#define HCS_MAX_SCRATCHPAD(p) (((p) >> 27) & 0x1f) +/* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */ +#define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f)) /* HCSPARAMS3 - hcs_params3 - bitmasks */ /* bits 0:7, Max U1 to U0 latency for the roothub ports */ -- cgit v1.2.3-59-g8ed1b From 27082e2654dc148078b0abdfc3c8e5ccbde0ebfa Mon Sep 17 00:00:00 2001 From: Mathias Nyman Date: Tue, 24 Feb 2015 18:27:02 +0200 Subject: xhci: Clear the host side toggle manually when endpoint is 'soft reset' Main benefit of this is to get xhci connected USB scanners to work. Some devices use a clear endpoint halt request as a 'soft reset' even if the endpoint is not halted. This will clear the toggle and sequence on the device side. xHCI however refuses to reset a non-halted endpoint, so instead we need to issue a configure endpoint command on xHCI to clear its host side toggle and sequence, and get it in sync with the device side. Tested-by: Mike Mammarella Cc: # v3.18 Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 2 +- drivers/usb/host/xhci.c | 100 +++++++++++++++++++++++++++++++++++++++---- drivers/usb/host/xhci.h | 2 + 3 files changed, 94 insertions(+), 10 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 88da8d629820..b46b5b98a943 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1729,7 +1729,7 @@ static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci, if (!command) return; - ep->ep_state |= EP_HALTED; + ep->ep_state |= EP_HALTED | EP_RECENTLY_HALTED; ep->stopped_stream = stream_id; xhci_queue_reset_ep(xhci, command, slot_id, ep_index); diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index ec8ac1674854..b06d1a53652d 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -1338,6 +1338,12 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) goto exit; } + /* Reject urb if endpoint is in soft reset, queue must stay empty */ + if (xhci->devs[slot_id]->eps[ep_index].ep_state & EP_CONFIG_PENDING) { + xhci_warn(xhci, "Can't enqueue URB while ep is in soft reset\n"); + ret = -EINVAL; + } + if (usb_endpoint_xfer_isoc(&urb->ep->desc)) size = urb->number_of_packets; else @@ -2948,23 +2954,36 @@ void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci, } } -/* Called when clearing halted device. The core should have sent the control +/* Called after clearing a halted device. USB core should have sent the control * message to clear the device halt condition. The host side of the halt should - * already be cleared with a reset endpoint command issued when the STALL tx - * event was received. - * - * Context: in_interrupt + * already be cleared with a reset endpoint command issued immediately when the + * STALL tx event was received. */ void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep) { struct xhci_hcd *xhci; + struct usb_device *udev; + struct xhci_virt_device *virt_dev; + struct xhci_virt_ep *virt_ep; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_command *command; + unsigned int ep_index, ep_state; + unsigned long flags; + u32 ep_flag; xhci = hcd_to_xhci(hcd); + udev = (struct usb_device *) ep->hcpriv; + if (!ep->hcpriv) + return; + virt_dev = xhci->devs[udev->slot_id]; + ep_index = xhci_get_endpoint_index(&ep->desc); + virt_ep = &virt_dev->eps[ep_index]; + ep_state = virt_ep->ep_state; /* - * We might need to implement the config ep cmd in xhci 4.8.1 note: + * Implement the config ep command in xhci 4.6.8 additional note: * The Reset Endpoint Command may only be issued to endpoints in the * Halted state. If software wishes reset the Data Toggle or Sequence * Number of an endpoint that isn't in the Halted state, then software @@ -2972,9 +2991,72 @@ void xhci_endpoint_reset(struct usb_hcd *hcd, * for the target endpoint. that is in the Stopped state. */ - /* For now just print debug to follow the situation */ - xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n", - ep->desc.bEndpointAddress); + if (ep_state & SET_DEQ_PENDING || ep_state & EP_RECENTLY_HALTED) { + virt_ep->ep_state &= ~EP_RECENTLY_HALTED; + xhci_dbg(xhci, "ep recently halted, no toggle reset needed\n"); + return; + } + + /* Only interrupt and bulk ep's use Data toggle, USB2 spec 5.5.4-> */ + if (usb_endpoint_xfer_control(&ep->desc) || + usb_endpoint_xfer_isoc(&ep->desc)) + return; + + ep_flag = xhci_get_endpoint_flag(&ep->desc); + + if (ep_flag == SLOT_FLAG || ep_flag == EP0_FLAG) + return; + + command = xhci_alloc_command(xhci, true, true, GFP_NOWAIT); + if (!command) { + xhci_err(xhci, "Could not allocate xHCI command structure.\n"); + return; + } + + spin_lock_irqsave(&xhci->lock, flags); + + /* block ringing ep doorbell */ + virt_ep->ep_state |= EP_CONFIG_PENDING; + + /* + * Make sure endpoint ring is empty before resetting the toggle/seq. + * Driver is required to synchronously cancel all transfer request. + * + * xhci 4.6.6 says we can issue a configure endpoint command on a + * running endpoint ring as long as it's idle (queue empty) + */ + + if (!list_empty(&virt_ep->ring->td_list)) { + dev_err(&udev->dev, "EP not empty, refuse reset\n"); + spin_unlock_irqrestore(&xhci->lock, flags); + goto cleanup; + } + + xhci_dbg(xhci, "Reset toggle/seq for slot %d, ep_index: %d\n", + udev->slot_id, ep_index); + + ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx); + if (!ctrl_ctx) { + xhci_err(xhci, "Could not get input context, bad type. virt_dev: %p, in_ctx %p\n", + virt_dev, virt_dev->in_ctx); + spin_unlock_irqrestore(&xhci->lock, flags); + goto cleanup; + } + xhci_setup_input_ctx_for_config_ep(xhci, command->in_ctx, + virt_dev->out_ctx, ctrl_ctx, + ep_flag, ep_flag); + xhci_endpoint_copy(xhci, command->in_ctx, virt_dev->out_ctx, ep_index); + + xhci_queue_configure_endpoint(xhci, command, command->in_ctx->dma, + udev->slot_id, false); + xhci_ring_cmd_db(xhci); + spin_unlock_irqrestore(&xhci->lock, flags); + + wait_for_completion(command->completion); + +cleanup: + virt_ep->ep_state &= ~EP_CONFIG_PENDING; + xhci_free_command(xhci, command); } static int xhci_check_streams_endpoint(struct xhci_hcd *xhci, diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 68956b13b8d1..3b97f0582155 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -864,6 +864,8 @@ struct xhci_virt_ep { #define EP_HAS_STREAMS (1 << 4) /* Transitioning the endpoint to not using streams, don't enqueue URBs */ #define EP_GETTING_NO_STREAMS (1 << 5) +#define EP_RECENTLY_HALTED (1 << 6) +#define EP_CONFIG_PENDING (1 << 7) /* ---- Related to URB cancellation ---- */ struct list_head cancelled_td_list; struct xhci_td *stopped_td; -- cgit v1.2.3-59-g8ed1b From f0c2b68198589249afd2b1f2c4e8de8c03e19c16 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Fri, 13 Feb 2015 10:54:53 -0500 Subject: USB: usbfs: don't leak kernel data in siginfo When a signal is delivered, the information in the siginfo structure is copied to userspace. Good security practice dicatates that the unused fields in this structure should be initialized to 0 so that random kernel stack data isn't exposed to the user. This patch adds such an initialization to the two places where usbfs raises signals. Signed-off-by: Alan Stern Reported-by: Dave Mielke CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 66abdbcfbfa5..11635537c052 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -501,6 +501,7 @@ static void async_completed(struct urb *urb) as->status = urb->status; signr = as->signr; if (signr) { + memset(&sinfo, 0, sizeof(sinfo)); sinfo.si_signo = as->signr; sinfo.si_errno = as->status; sinfo.si_code = SI_ASYNCIO; @@ -2382,6 +2383,7 @@ static void usbdev_remove(struct usb_device *udev) wake_up_all(&ps->wait); list_del_init(&ps->list); if (ps->discsignr) { + memset(&sinfo, 0, sizeof(sinfo)); sinfo.si_signo = ps->discsignr; sinfo.si_errno = EPIPE; sinfo.si_code = SI_ASYNCIO; -- cgit v1.2.3-59-g8ed1b From 59e980efafd27df83a5c85c054f906d82bcbf752 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Mon, 23 Feb 2015 13:41:14 +0100 Subject: uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539 Like the JMicron JMS567 enclosures with the JMS539 choke on report-opcodes, so avoid it. Tested-and-reported-by: Tom Arild Naess Cc: stable@vger.kernel.org # 3.16 Signed-off-by: Hans de Goede Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_uas.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/usb/storage/unusual_uas.h b/drivers/usb/storage/unusual_uas.h index dbc00e56c7f5..82570425fdfe 100644 --- a/drivers/usb/storage/unusual_uas.h +++ b/drivers/usb/storage/unusual_uas.h @@ -113,6 +113,13 @@ UNUSUAL_DEV(0x0bc2, 0xab2a, 0x0000, 0x9999, USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NO_ATA_1X), +/* Reported-by: Tom Arild Naess */ +UNUSUAL_DEV(0x152d, 0x0539, 0x0000, 0x9999, + "JMicron", + "JMS539", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_NO_REPORT_OPCODES), + /* Reported-by: Claudio Bizzarri */ UNUSUAL_DEV(0x152d, 0x0567, 0x0000, 0x9999, "JMicron", -- cgit v1.2.3-59-g8ed1b From ec371326d47385dd3fc8e6c7e0d9e89118d94dd8 Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Tue, 10 Feb 2015 09:27:59 +0100 Subject: usb-storage: support for more than 8 LUNs This is necessary to make some storage arrays work. Some storage devices have more than 8 LUNs. In addition you can hook up a WideSCSI bus to USB. In these cases even level 2 devices can have more than 8 LUNs. For them it is necessary to simply believe the class specific command and report its result back to the SCSI layer. Off by one Alan noticed is fixed. Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/usb.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c index d468d02179f4..5600c33fcadb 100644 --- a/drivers/usb/storage/usb.c +++ b/drivers/usb/storage/usb.c @@ -889,6 +889,12 @@ static void usb_stor_scan_dwork(struct work_struct *work) !(us->fflags & US_FL_SCM_MULT_TARG)) { mutex_lock(&us->dev_mutex); us->max_lun = usb_stor_Bulk_max_lun(us); + /* + * Allow proper scanning of devices that present more than 8 LUNs + * While not affecting other devices that may need the previous behavior + */ + if (us->max_lun >= 8) + us_to_host(us)->max_lun = us->max_lun+1; mutex_unlock(&us->dev_mutex); } scsi_scan_host(us_to_host(us)); -- cgit v1.2.3-59-g8ed1b From b20b1618b8fca858c83e52da4aa22cd6b13b0359 Mon Sep 17 00:00:00 2001 From: Björn Gerhart Date: Wed, 18 Feb 2015 07:19:44 +0100 Subject: cdc-acm: Add support for Denso cradle CU-321 In order to support an older USB cradle by Denso, I added its vendor- and product-ID to the array of usb_device_id acm_ids. In this way cdc-acm feels responsible for this cradle. The related /dev/ttyACM node is being created properly, and the data transfer works. However, later cradle models by Denso do have proper descriptors, so the patch is not required for these. At the same time both the older and the later model have the same vendor- and product-ID, but they both work with the patched driver. Declaration of the Denso cradles I tested: - both models have the same IDs: vendorID 0x076d, productID 0x0006 - older model: Denso CU-321 (descriptors not properly set) - later model: Denso CU-821 (with proper descriptors) Signed-off-by: Bjoern Gerhart Acked-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index e78720b59d67..683617714e7c 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -1650,6 +1650,8 @@ static int acm_reset_resume(struct usb_interface *intf) static const struct usb_device_id acm_ids[] = { /* quirky and broken devices */ + { USB_DEVICE(0x076d, 0x0006), /* Denso Cradle CU-321 */ + .driver_info = NO_UNION_NORMAL, },/* has no union descriptor */ { USB_DEVICE(0x17ef, 0x7000), /* Lenovo USB modem */ .driver_info = NO_UNION_NORMAL, },/* has no union descriptor */ { USB_DEVICE(0x0870, 0x0001), /* Metricom GS Modem */ -- cgit v1.2.3-59-g8ed1b From a54879a0085993c06be5630321d962d6b48e134f Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 24 Feb 2015 08:48:52 -0800 Subject: ARM: dts: Fix USB dts configuration for dm816x Commit 7800064ba507 ("ARM: dts: Add basic dm816x device tree configuration") added basic devices for dm816x, but I was not able to test the USB completely because of an unconfigured USB phy, and I only tested it to make sure the Mentor chips are detected and clocked without a phy. After testing the USB with actual devices I noticed a few issues that should be fixed to avoid confusion: - The USB id pin on dm8168-evm is hardwired and can be changed only by software. As there are two USB-A type connectors, let's start both in host mode instead of otg. - The Mentor core is configured in such a way on dm8168-evm that it's not capable of multipoint at least on revision c board that I have. - We need ranges for the syscon to properly set up the phy as children of the SCM syscon area. - Let's not disable the second interface, the board specific dts files can do that if really needed. Most boards should just keep it enabled to ensure the device is idled properly. Note that also a phy and several musb fixes are still needed to make the USB to work properly in addition to this fix. Cc: Brian Hutchinson Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm8168-evm.dts | 25 +++++++++++++++++++++++++ arch/arm/boot/dts/dm816x.dtsi | 34 ++++++++++++++++++++++++++++++---- 2 files changed, 55 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts index 857d0289ad4d..d3a29c1b8417 100644 --- a/arch/arm/boot/dts/dm8168-evm.dts +++ b/arch/arm/boot/dts/dm8168-evm.dts @@ -35,6 +35,18 @@ DM816X_IOPAD(0x0aac, PIN_INPUT | MUX_MODE0) /* SPI_D1 */ >; }; + + usb0_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM816X_IOPAD(0x0d00, MUX_MODE0) /* USB0_DRVVBUS */ + >; + }; + + usb1_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM816X_IOPAD(0x0d04, MUX_MODE0) /* USB1_DRVVBUS */ + >; + }; }; &i2c1 { @@ -127,3 +139,16 @@ &mmc1 { vmmc-supply = <&vmmcsd_fixed>; }; + +/* At least dm8168-evm rev c won't support multipoint, later may */ +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; + mentor,multipoint = <0>; +}; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; + mentor,multipoint = <0>; +}; diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index d98d0f7de380..3c97b5f2addc 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -97,10 +97,31 @@ /* Device Configuration Registers */ scm_conf: syscon@600 { - compatible = "syscon"; + compatible = "syscon", "simple-bus"; reg = <0x600 0x110>; #address-cells = <1>; #size-cells = <1>; + ranges = <0 0x600 0x110>; + + usb_phy0: usb-phy@20 { + compatible = "ti,dm8168-usb-phy"; + reg = <0x20 0x8>; + reg-names = "phy"; + clocks = <&main_fapll 6>; + clock-names = "refclk"; + #phy-cells = <0>; + syscon = <&scm_conf>; + }; + + usb_phy1: usb-phy@28 { + compatible = "ti,dm8168-usb-phy"; + reg = <0x28 0x8>; + reg-names = "phy"; + clocks = <&main_fapll 6>; + clock-names = "refclk"; + #phy-cells = <0>; + syscon = <&scm_conf>; + }; }; scrm_clocks: clocks { @@ -357,7 +378,10 @@ reg-names = "mc", "control"; interrupts = <18>; interrupt-names = "mc"; - dr_mode = "otg"; + dr_mode = "host"; + interface-type = <0>; + phys = <&usb_phy0>; + phy-names = "usb2-phy"; mentor,multipoint = <1>; mentor,num-eps = <16>; mentor,ram-bits = <12>; @@ -366,13 +390,15 @@ usb1: usb@47401800 { compatible = "ti,musb-am33xx"; - status = "disabled"; reg = <0x47401c00 0x400 0x47401800 0x200>; reg-names = "mc", "control"; interrupts = <19>; interrupt-names = "mc"; - dr_mode = "otg"; + dr_mode = "host"; + interface-type = <0>; + phys = <&usb_phy1>; + phy-names = "usb2-phy"; mentor,multipoint = <1>; mentor,num-eps = <16>; mentor,ram-bits = <12>; -- cgit v1.2.3-59-g8ed1b From 3992b62da72d124698bf6157889ab45197ddec69 Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Fri, 6 Feb 2015 16:55:46 +0200 Subject: thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP Fix following build warning if CONFIG_PM_SLEEP is not set: drivers/thermal/ti-soc-thermal/ti-bandgap.c:1478:12: warning: 'ti_bandgap_suspend' defined but not used [-Wunused-function] static int ti_bandgap_suspend(struct device *dev) ^ drivers/thermal/ti-soc-thermal/ti-bandgap.c:1492:12: warning: 'ti_bandgap_resume' defined but not used [-Wunused-function] static int ti_bandgap_resume(struct device *dev) ^ Acked-by: Nishanth Menon Signed-off-by: Grygorii Strashko Signed-off-by: Eduardo Valentin --- drivers/thermal/ti-soc-thermal/ti-bandgap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c index 634b6ce0e63a..62a5d449c388 100644 --- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c +++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c @@ -1402,7 +1402,7 @@ int ti_bandgap_remove(struct platform_device *pdev) return 0; } -#ifdef CONFIG_PM +#ifdef CONFIG_PM_SLEEP static int ti_bandgap_save_ctxt(struct ti_bandgap *bgp) { int i; -- cgit v1.2.3-59-g8ed1b From 9ca9be2b09ea1b5289b936e917c8a93119a65736 Mon Sep 17 00:00:00 2001 From: Markus Elfring Date: Tue, 3 Feb 2015 11:15:14 +0100 Subject: ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister" The cpufreq_cooling_unregister() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring Signed-off-by: Eduardo Valentin --- drivers/thermal/ti-soc-thermal/ti-thermal-common.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/thermal/ti-soc-thermal/ti-thermal-common.c b/drivers/thermal/ti-soc-thermal/ti-thermal-common.c index 3fb054a10f6a..a38c1756442a 100644 --- a/drivers/thermal/ti-soc-thermal/ti-thermal-common.c +++ b/drivers/thermal/ti-soc-thermal/ti-thermal-common.c @@ -429,7 +429,7 @@ int ti_thermal_unregister_cpu_cooling(struct ti_bandgap *bgp, int id) data = ti_bandgap_get_sensor_data(bgp, id); - if (data && data->cool_dev) + if (data) cpufreq_cooling_unregister(data->cool_dev); return 0; -- cgit v1.2.3-59-g8ed1b From 1861cda0de66d02688a9b3cba658ff9ab847e26d Mon Sep 17 00:00:00 2001 From: Ivaylo Dimitrov Date: Sun, 8 Feb 2015 17:48:56 +0200 Subject: ARM: dts: n900: fix i2c bus numbering MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit With legacy boot i2c buses on Nokia N900 are numbered i2c1, i2c2 and i2c3. Commit 20b80942ef4e ("ARM: dts: OMAP3+: Add i2c aliases") fixed the numbering with DT boot, but introduced a regression on N900 - aliases become i2c0, i2c1 and i2c2. Fix that by providing the correct aliases in the board dts. Signed-off-by: Ivaylo Dimitrov Tested-by: Pali Rohár Acked-by: Nishanth Menon [tony@atomide.com: this is needed for legacy user space to work] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-n900.dts | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index 60403273f83e..bef131d1aef1 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -16,6 +16,13 @@ model = "Nokia N900"; compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3"; + aliases { + i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + }; + cpus { cpu@0 { cpu0-supply = <&vcc>; -- cgit v1.2.3-59-g8ed1b From cb9071d4bb0d61cc5a375cc9ed5fefed5bb65e09 Mon Sep 17 00:00:00 2001 From: Pali Rohár Date: Thu, 19 Feb 2015 17:49:50 +0100 Subject: ARM: dts: n900: Fix offset for smc91x ethernet MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Offset for smc91x must be zero otherwise smc91x linux kernel driver does not detect smc91x ethernet hardware in qemu N900 machine. The 0x300 offset was used to supress a warning the smsc911x driver produces about non-standard offset as 0x300 seems to be the EEPROM default. As only three address lines are connected both 0 and 0x300 will work just fine with 0 being correct. The warning about the non-standard offset can be fixed by writing to EEPROM as that's needed in any case to set the MAC address. Signed-off-by: Pali Rohár [tony@atomide.com: updated comments, just use 0 instead of 0x0] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-n900.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index bef131d1aef1..db80f9d376fa 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -711,7 +711,7 @@ compatible = "smsc,lan91c94"; interrupt-parent = <&gpio2>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */ - reg = <1 0x300 0xf>; /* 16 byte IO range at offset 0x300 */ + reg = <1 0 0xf>; /* 16 byte IO range */ bank-width = <2>; pinctrl-names = "default"; pinctrl-0 = <ðernet_pins>; -- cgit v1.2.3-59-g8ed1b From 123604482599631137cfae027d6475a04b854f8c Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 19 Feb 2015 12:03:54 -0600 Subject: ARM: dts: am437x-idk: fix TPS62362 i2c bus As it turns out, tps62362 is actually on I2C bus0, not bus1. This has gone unnoticed because Linux doesn't use (as of now) that regulator at all, it's setup by the bootloader and left as is. While at that, also add missing reg property for our regulator. Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-idk-evm.dts | 23 +---------------------- 1 file changed, 1 insertion(+), 22 deletions(-) diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/am437x-idk-evm.dts index f9a17e2ca8cb..2471f1ebd4ed 100644 --- a/arch/arm/boot/dts/am437x-idk-evm.dts +++ b/arch/arm/boot/dts/am437x-idk-evm.dts @@ -133,20 +133,6 @@ >; }; - i2c1_pins_default: i2c1_pins_default { - pinctrl-single,pins = < - 0x15c (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c1_scl */ - 0x158 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_d1.i2c1_sda */ - >; - }; - - i2c1_pins_sleep: i2c1_pins_sleep { - pinctrl-single,pins = < - 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_cs0.i2c1_scl */ - 0x158 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d1.i2c1_sda */ - >; - }; - mmc1_pins_default: pinmux_mmc1_pins_default { pinctrl-single,pins = < 0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ @@ -262,17 +248,10 @@ pagesize = <64>; reg = <0x50>; }; -}; - -&i2c1 { - status = "okay"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c1_pins_default>; - pinctrl-1 = <&i2c1_pins_default>; - clock-frequency = <400000>; tps: tps62362@60 { compatible = "ti,tps62362"; + reg = <0x60>; regulator-name = "VDD_MPU"; regulator-min-microvolt = <950000>; regulator-max-microvolt = <1330000>; -- cgit v1.2.3-59-g8ed1b From 57fd4e5d380fcb4d2f1641a7b2ad26632a448282 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 19 Feb 2015 12:03:55 -0600 Subject: ARM: omap2plus_defconfig: enable TPS62362 regulator This regulator is used on AM437x Industrial Development Kit. Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index b7386524c356..8ff1a988c0f4 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -248,6 +248,7 @@ CONFIG_TWL6040_CORE=y CONFIG_REGULATOR_PALMAS=y CONFIG_REGULATOR_PBIAS=y CONFIG_REGULATOR_TI_ABB=y +CONFIG_REGULATOR_TPS62360=m CONFIG_REGULATOR_TPS65023=y CONFIG_REGULATOR_TPS6507X=y CONFIG_REGULATOR_TPS65217=y -- cgit v1.2.3-59-g8ed1b From ee5d9cd2b31df90aba7812c8c9ce5a70948a28f8 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 19 Feb 2015 13:57:08 -0600 Subject: ARM: dts: am437x-idk: fix sleep pinctrl state we have i2c0 sleep pinctrl state but were passing default state anyhow. Fix that. Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-idk-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/am437x-idk-evm.dts index 2471f1ebd4ed..0198f5a62b96 100644 --- a/arch/arm/boot/dts/am437x-idk-evm.dts +++ b/arch/arm/boot/dts/am437x-idk-evm.dts @@ -240,7 +240,7 @@ status = "okay"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c0_pins_default>; - pinctrl-1 = <&i2c0_pins_default>; + pinctrl-1 = <&i2c0_pins_sleep>; clock-frequency = <400000>; at24@50 { -- cgit v1.2.3-59-g8ed1b From caa73a46888f00b12202406f93f36c5c8feaa8fb Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Fri, 20 Feb 2015 15:42:02 +0200 Subject: ARM: dts: omap2: Correct the dma controller's property names According to the Documentation/devicetree/bindings/dma/dma.txt the dma-channels and dma-requests property should not have '#'. Signed-off-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap2.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi index 59d1c297bb30..578fa2a54dce 100644 --- a/arch/arm/boot/dts/omap2.dtsi +++ b/arch/arm/boot/dts/omap2.dtsi @@ -87,8 +87,8 @@ <14>, <15>; #dma-cells = <1>; - #dma-channels = <32>; - #dma-requests = <64>; + dma-channels = <32>; + dma-requests = <64>; }; i2c1: i2c@48070000 { -- cgit v1.2.3-59-g8ed1b From 7e8d25d5960badb10ba739a1b8a5f33e2cbd988a Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Fri, 20 Feb 2015 15:42:03 +0200 Subject: ARM: dts: omap3: Correct the dma controller's property names According to the Documentation/devicetree/bindings/dma/dma.txt the dma-channels and dma-requests property should not have '#'. Signed-off-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 01b71111bd55..f4f78c40b564 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -155,8 +155,8 @@ <14>, <15>; #dma-cells = <1>; - #dma-channels = <32>; - #dma-requests = <96>; + dma-channels = <32>; + dma-requests = <96>; }; omap3_pmx_core: pinmux@48002030 { -- cgit v1.2.3-59-g8ed1b From 24ac17704943aaa2fb5e5d4b9dffc911aec41d88 Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Fri, 20 Feb 2015 15:42:04 +0200 Subject: ARM: dts: omap4: Correct the dma controller's property names According to the Documentation/devicetree/bindings/dma/dma.txt the dma-channels and dma-requests property should not have '#'. Signed-off-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 074147cebae4..87401d9f4d8b 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -223,8 +223,8 @@ , ; #dma-cells = <1>; - #dma-channels = <32>; - #dma-requests = <127>; + dma-channels = <32>; + dma-requests = <127>; }; gpio1: gpio@4a310000 { -- cgit v1.2.3-59-g8ed1b From 951c1c04c63906d7ba9462741d42a947ea838bf7 Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Fri, 20 Feb 2015 15:42:05 +0200 Subject: ARM: dts: omap5: Correct the dma controller's property names According to the Documentation/devicetree/bindings/dma/dma.txt the dma-channels and dma-requests property should not have '#'. Signed-off-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index bb498e7cc0f1..ddff674bd05e 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -238,8 +238,8 @@ , ; #dma-cells = <1>; - #dma-channels = <32>; - #dma-requests = <127>; + dma-channels = <32>; + dma-requests = <127>; }; gpio1: gpio@4ae10000 { -- cgit v1.2.3-59-g8ed1b From 08d9b327e6289a9fdf6c3fe9830053bb099d820a Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Fri, 20 Feb 2015 15:42:06 +0200 Subject: ARM: dts: dra7: Correct the dma controller's property names According to the Documentation/devicetree/bindings/dma/dma.txt the dma-channels and dma-requests property should not have '#'. Signed-off-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 853d37d96007..127608d79033 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -249,8 +249,8 @@ , ; #dma-cells = <1>; - #dma-channels = <32>; - #dma-requests = <127>; + dma-channels = <32>; + dma-requests = <127>; }; gpio1: gpio@4ae10000 { -- cgit v1.2.3-59-g8ed1b From f8c360588ccdaa80b8878688653d41417589cdc7 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 23 Feb 2015 17:18:36 +0200 Subject: ARM: omap2plus_defconfig: Enable OMAP NAND BCH driver Without this NAND doesn't work on most EVMs. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 8ff1a988c0f4..c090989b042f 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -114,6 +114,7 @@ CONFIG_MTD_PHYSMAP_OF=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_ECC_BCH=y CONFIG_MTD_NAND_OMAP2=y +CONFIG_MTD_NAND_OMAP_BCH=y CONFIG_MTD_ONENAND=y CONFIG_MTD_ONENAND_VERIFY_WRITE=y CONFIG_MTD_ONENAND_OMAP2=y -- cgit v1.2.3-59-g8ed1b From acd83a1652dc60cfb5b3e6f061f48b87044c9b20 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 23 Feb 2015 17:18:37 +0200 Subject: ARM: omap2plus_defconfig: Fix SATA boot SATA operation depends on PIPE3 PHY and if we want to boot from SATA drives, we have to have the PIPE3 PHY driver built-in. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index c090989b042f..a097cffa1231 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -376,7 +376,7 @@ CONFIG_PWM_TIEHRPWM=m CONFIG_PWM_TWL=m CONFIG_PWM_TWL_LED=m CONFIG_OMAP_USB2=m -CONFIG_TI_PIPE3=m +CONFIG_TI_PIPE3=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -- cgit v1.2.3-59-g8ed1b From addfcde7c485781c9bc076bb7a20faf3e07554ad Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 24 Feb 2015 14:37:07 +0200 Subject: ARM: dts: dra7x-evm: beagle-x15: Fix USB Host In commit 87517d26d888 ("ARM: dts: dra7-evm: Add extcon nodes for USB") we enabled Extcon USB gpio to tackle the USB ID pin and get peripheral mode to work. But the extcon-gpio-usb driver [1] didn't make it into v4.0 and this makes the USB driver defer probe indefinitely breaking USB Host functionality. As a temporary fix we remove the extcon handle from the USB controller and add it back when the extcon driver merges in v4.1. [1] - https://lkml.org/lkml/2015/2/2/187 Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-beagle-x15.dts | 8 -------- arch/arm/boot/dts/dra7-evm.dts | 8 -------- arch/arm/boot/dts/dra72-evm.dts | 8 -------- 3 files changed, 24 deletions(-) diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index 03750af3b49a..6463f9ef2b54 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -549,14 +549,6 @@ pinctrl-0 = <&usb1_pins>; }; -&omap_dwc3_1 { - extcon = <&extcon_usb1>; -}; - -&omap_dwc3_2 { - extcon = <&extcon_usb2>; -}; - &usb2 { dr_mode = "peripheral"; }; diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 746cddb1b8f5..3290a96ba586 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -543,14 +543,6 @@ }; }; -&omap_dwc3_1 { - extcon = <&extcon_usb1>; -}; - -&omap_dwc3_2 { - extcon = <&extcon_usb2>; -}; - &usb1 { dr_mode = "peripheral"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 4d8711713610..e0264d0bf7b9 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -380,14 +380,6 @@ phy-supply = <&ldo4_reg>; }; -&omap_dwc3_1 { - extcon = <&extcon_usb1>; -}; - -&omap_dwc3_2 { - extcon = <&extcon_usb2>; -}; - &usb1 { dr_mode = "peripheral"; pinctrl-names = "default"; -- cgit v1.2.3-59-g8ed1b From 67fd14b3eca63b14429350e9eadc5fab709a8821 Mon Sep 17 00:00:00 2001 From: Robert Nelson Date: Tue, 24 Feb 2015 10:10:43 -0600 Subject: ARM: dts: am335x-bone*: usb0 is hardwired for peripheral Fixes: http://bugs.elinux.org/issues/127 the bb.org community was seeing random reboots before this change. Signed-off-by: Robert Nelson Reviewed-by: Felipe Balbi Acked-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-bone-common.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 6cc25ed912ee..2c6248d9a9ef 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -195,6 +195,7 @@ &usb0 { status = "okay"; + dr_mode = "peripheral"; }; &usb1 { -- cgit v1.2.3-59-g8ed1b From 12ca7188468ee29c4e717f73db4bf43c90954fc7 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Fri, 13 Feb 2015 19:28:02 -0600 Subject: thermal: Introduce dummy functions when thermal is not defined When CONFIG_THERMAL is not enabled, it is better to introduce equivalent dummy functions in the exported header than to introduce #ifdeffery in drivers using the function. This will prevent issues such as that reported in: http://www.spinics.net/lists/linux-next/msg31573.html While at it switch over to IS_ENABLED for thermal macros to allow for thermal framework to be built as framework and relevant APIs be usable by relevant drivers as a result. Reported-by: Guenter Roeck Signed-off-by: Nishanth Menon Signed-off-by: Eduardo Valentin --- include/linux/thermal.h | 56 +++++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 54 insertions(+), 2 deletions(-) diff --git a/include/linux/thermal.h b/include/linux/thermal.h index fc52e307efab..5eac316490ea 100644 --- a/include/linux/thermal.h +++ b/include/linux/thermal.h @@ -314,6 +314,8 @@ void thermal_zone_of_sensor_unregister(struct device *dev, } #endif + +#if IS_ENABLED(CONFIG_THERMAL) struct thermal_zone_device *thermal_zone_device_register(const char *, int, int, void *, struct thermal_zone_device_ops *, const struct thermal_zone_params *, int, int); @@ -340,8 +342,58 @@ struct thermal_instance *get_thermal_instance(struct thermal_zone_device *, struct thermal_cooling_device *, int); void thermal_cdev_update(struct thermal_cooling_device *); void thermal_notify_framework(struct thermal_zone_device *, int); - -#ifdef CONFIG_NET +#else +static inline struct thermal_zone_device *thermal_zone_device_register( + const char *type, int trips, int mask, void *devdata, + struct thermal_zone_device_ops *ops, + const struct thermal_zone_params *tzp, + int passive_delay, int polling_delay) +{ return ERR_PTR(-ENODEV); } +static inline void thermal_zone_device_unregister( + struct thermal_zone_device *tz) +{ } +static inline int thermal_zone_bind_cooling_device( + struct thermal_zone_device *tz, int trip, + struct thermal_cooling_device *cdev, + unsigned long upper, unsigned long lower) +{ return -ENODEV; } +static inline int thermal_zone_unbind_cooling_device( + struct thermal_zone_device *tz, int trip, + struct thermal_cooling_device *cdev) +{ return -ENODEV; } +static inline void thermal_zone_device_update(struct thermal_zone_device *tz) +{ } +static inline struct thermal_cooling_device * +thermal_cooling_device_register(char *type, void *devdata, + const struct thermal_cooling_device_ops *ops) +{ return ERR_PTR(-ENODEV); } +static inline struct thermal_cooling_device * +thermal_of_cooling_device_register(struct device_node *np, + char *type, void *devdata, const struct thermal_cooling_device_ops *ops) +{ return ERR_PTR(-ENODEV); } +static inline void thermal_cooling_device_unregister( + struct thermal_cooling_device *cdev) +{ } +static inline struct thermal_zone_device *thermal_zone_get_zone_by_name( + const char *name) +{ return ERR_PTR(-ENODEV); } +static inline int thermal_zone_get_temp( + struct thermal_zone_device *tz, unsigned long *temp) +{ return -ENODEV; } +static inline int get_tz_trend(struct thermal_zone_device *tz, int trip) +{ return -ENODEV; } +static inline struct thermal_instance * +get_thermal_instance(struct thermal_zone_device *tz, + struct thermal_cooling_device *cdev, int trip) +{ return ERR_PTR(-ENODEV); } +static inline void thermal_cdev_update(struct thermal_cooling_device *cdev) +{ } +static inline void thermal_notify_framework(struct thermal_zone_device *tz, + int trip) +{ } +#endif /* CONFIG_THERMAL */ + +#if defined(CONFIG_NET) && IS_ENABLED(CONFIG_THERMAL) extern int thermal_generate_netlink_event(struct thermal_zone_device *tz, enum events event); #else -- cgit v1.2.3-59-g8ed1b From 7ed620bb343f434f8a85f830020c04988df2a140 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Thu, 19 Feb 2015 20:18:03 -0800 Subject: efi/libstub: Fix boundary checking in efi_high_alloc() While adding support loading kernel and initrd above 4G to grub2 in legacy mode, I was referring to efi_high_alloc(). That will allocate buffer for kernel and then initrd, and initrd will use kernel buffer start as limit. During testing found two buffers will be overlapped when initrd size is very big like 400M. It turns out efi_high_alloc() boundary checking is not right. end - size will be the new start, and should not compare new start with max, we need to make sure end is smaller than max. [ Basically, with the current efi_high_alloc() code it's possible to allocate memory above 'max', because efi_high_alloc() doesn't check that the tail of the allocation is below 'max'. If you have an EFI memory map with a single entry that looks like so, [0xc0000000-0xc0004000] And want to allocate 0x3000 bytes below 0xc0003000 the current code will allocate [0xc0001000-0xc0004000], not [0xc0000000-0xc0003000] like you would expect. - Matt ] Signed-off-by: Yinghai Lu Reviewed-by: Ard Biesheuvel Reviewed-by: Mark Rutland Tested-by: Mark Rutland Cc: Signed-off-by: Matt Fleming --- drivers/firmware/efi/libstub/efi-stub-helper.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/firmware/efi/libstub/efi-stub-helper.c b/drivers/firmware/efi/libstub/efi-stub-helper.c index 9bd9fbb5bea8..c927bccd92bd 100644 --- a/drivers/firmware/efi/libstub/efi-stub-helper.c +++ b/drivers/firmware/efi/libstub/efi-stub-helper.c @@ -170,12 +170,12 @@ again: start = desc->phys_addr; end = start + desc->num_pages * (1UL << EFI_PAGE_SHIFT); - if ((start + size) > end || (start + size) > max) - continue; - - if (end - size > max) + if (end > max) end = max; + if ((start + size) > end) + continue; + if (round_down(end - size, align) < start) continue; -- cgit v1.2.3-59-g8ed1b From 6d9ff473317245e3e5cd9922b4520411c2296388 Mon Sep 17 00:00:00 2001 From: Ivan Khoronzhuk Date: Wed, 18 Feb 2015 13:33:19 +0200 Subject: firmware: dmi_scan: Fix dmi_len type According to SMBIOSv3 specification the length of DMI table can be up to 32bits wide. So use appropriate type to avoid overflow. It's obvious that dmi_num theoretically can be more than u16 also, so it's can be changed to u32 or at least it's better to use int instead of u16, but on that moment I cannot imagine dmi structure count more than 65535 and it can require changing type of vars that work with it. So I didn't correct it. Acked-by: Ard Biesheuvel Signed-off-by: Ivan Khoronzhuk Cc: Signed-off-by: Matt Fleming --- drivers/firmware/dmi_scan.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/firmware/dmi_scan.c b/drivers/firmware/dmi_scan.c index a44b87c7b45c..69fac068669f 100644 --- a/drivers/firmware/dmi_scan.c +++ b/drivers/firmware/dmi_scan.c @@ -78,7 +78,7 @@ static const char * __init dmi_string(const struct dmi_header *dm, u8 s) * We have to be cautious here. We have seen BIOSes with DMI pointers * pointing to completely the wrong place for example */ -static void dmi_table(u8 *buf, int len, int num, +static void dmi_table(u8 *buf, u32 len, int num, void (*decode)(const struct dmi_header *, void *), void *private_data) { @@ -115,7 +115,7 @@ static void dmi_table(u8 *buf, int len, int num, } static phys_addr_t dmi_base; -static u16 dmi_len; +static u32 dmi_len; static u16 dmi_num; static int __init dmi_walk_early(void (*decode)(const struct dmi_header *, -- cgit v1.2.3-59-g8ed1b From 0b37a83a91e885250c68546ce7271ce722120c99 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 23 Feb 2015 16:37:24 +0100 Subject: thermal: rcar: Fix race condition between init and interrupt As soon as the interrupt has been enabled by devm_request_irq(), the interrupt routine may be called, depending on the current status of the hardware. However, at that point rcar_thermal_common hasn't been initialized complely yet. E.g. rcar_thermal_common.base is still NULL, causing a NULL pointer dereference: Unable to handle kernel NULL pointer dereference at virtual address 0000000c pgd = c0004000 [0000000c] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc7-ape6evm-04564-gb6e46cb7cbe82389 #30 Hardware name: Generic R8A73A4 (Flattened Device Tree) task: ee8953c0 ti: ee896000 task.ti: ee896000 PC is at rcar_thermal_irq+0x1c/0xf0 LR is at _raw_spin_lock_irqsave+0x48/0x54 Postpone the call to devm_request_irq() until all initialization has been done to fix this. Signed-off-by: Geert Uytterhoeven Acked-by: Kuninori Morimoto Signed-off-by: Eduardo Valentin --- drivers/thermal/rcar_thermal.c | 22 +++++++++------------- 1 file changed, 9 insertions(+), 13 deletions(-) diff --git a/drivers/thermal/rcar_thermal.c b/drivers/thermal/rcar_thermal.c index 2580a4872f90..3c2c1720ba4a 100644 --- a/drivers/thermal/rcar_thermal.c +++ b/drivers/thermal/rcar_thermal.c @@ -387,21 +387,9 @@ static int rcar_thermal_probe(struct platform_device *pdev) irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); if (irq) { - int ret; - /* * platform has IRQ support. * Then, driver uses common registers - */ - - ret = devm_request_irq(dev, irq->start, rcar_thermal_irq, 0, - dev_name(dev), common); - if (ret) { - dev_err(dev, "irq request failed\n "); - return ret; - } - - /* * rcar_has_irq_support() will be enabled */ res = platform_get_resource(pdev, IORESOURCE_MEM, mres++); @@ -456,8 +444,16 @@ static int rcar_thermal_probe(struct platform_device *pdev) } /* enable temperature comparation */ - if (irq) + if (irq) { + ret = devm_request_irq(dev, irq->start, rcar_thermal_irq, 0, + dev_name(dev), common); + if (ret) { + dev_err(dev, "irq request failed\n "); + goto error_unregister; + } + rcar_thermal_common_write(common, ENR, enr_bits); + } platform_set_drvdata(pdev, common); -- cgit v1.2.3-59-g8ed1b From ac71c7025ebc1ed25114b1be77dc60b7f8cb8544 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 23 Feb 2015 16:37:25 +0100 Subject: thermal: rcar: Make error and remove paths symmetrical with init Swap interrupt disable and thermal zone unregistration in the error and remove paths, to make them more symmetrical with the initialization path. Signed-off-by: Geert Uytterhoeven Acked-by: Kuninori Morimoto Signed-off-by: Eduardo Valentin --- drivers/thermal/rcar_thermal.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/thermal/rcar_thermal.c b/drivers/thermal/rcar_thermal.c index 3c2c1720ba4a..fe4e767018c4 100644 --- a/drivers/thermal/rcar_thermal.c +++ b/drivers/thermal/rcar_thermal.c @@ -463,9 +463,9 @@ static int rcar_thermal_probe(struct platform_device *pdev) error_unregister: rcar_thermal_for_each_priv(priv, common) { - thermal_zone_device_unregister(priv->zone); if (rcar_has_irq_support(priv)) rcar_thermal_irq_disable(priv); + thermal_zone_device_unregister(priv->zone); } pm_runtime_put(dev); @@ -481,9 +481,9 @@ static int rcar_thermal_remove(struct platform_device *pdev) struct rcar_thermal_priv *priv; rcar_thermal_for_each_priv(priv, common) { - thermal_zone_device_unregister(priv->zone); if (rcar_has_irq_support(priv)) rcar_thermal_irq_disable(priv); + thermal_zone_device_unregister(priv->zone); } pm_runtime_put(dev); -- cgit v1.2.3-59-g8ed1b From b71d399c7f2fe06b60b96155ec0b9ae167334e4a Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Tue, 24 Feb 2015 13:56:55 +0900 Subject: thermal: exynos: Clean-up code to use oneline entry for exynos compatible table This patch cleanup the code to use oneline for entry of exynos compatible table. Cc: Zhang Rui Cc: Eduardo Valentin Signed-off-by: Chanwoo Choi Acked-by: Lukasz Majewski Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 38 ++++++++++-------------------------- 1 file changed, 10 insertions(+), 28 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 933cd80a6bc5..1fc54ab911d2 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -918,34 +918,16 @@ static irqreturn_t exynos_tmu_irq(int irq, void *id) } static const struct of_device_id exynos_tmu_match[] = { - { - .compatible = "samsung,exynos3250-tmu", - }, - { - .compatible = "samsung,exynos4210-tmu", - }, - { - .compatible = "samsung,exynos4412-tmu", - }, - { - .compatible = "samsung,exynos5250-tmu", - }, - { - .compatible = "samsung,exynos5260-tmu", - }, - { - .compatible = "samsung,exynos5420-tmu", - }, - { - .compatible = "samsung,exynos5420-tmu-ext-triminfo", - }, - { - .compatible = "samsung,exynos5440-tmu", - }, - { - .compatible = "samsung,exynos7-tmu", - }, - {}, + { .compatible = "samsung,exynos3250-tmu", }, + { .compatible = "samsung,exynos4210-tmu", }, + { .compatible = "samsung,exynos4412-tmu", }, + { .compatible = "samsung,exynos5250-tmu", }, + { .compatible = "samsung,exynos5260-tmu", }, + { .compatible = "samsung,exynos5420-tmu", }, + { .compatible = "samsung,exynos5420-tmu-ext-triminfo", }, + { .compatible = "samsung,exynos5440-tmu", }, + { .compatible = "samsung,exynos7-tmu", }, + { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, exynos_tmu_match); -- cgit v1.2.3-59-g8ed1b From 17dce15801d5602719936045a7e84ff7dc6b6da2 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Thu, 19 Feb 2015 12:57:40 +0100 Subject: mac80211/minstrel: fix !x!=0 confusion Commit 06d961a8e210 ("mac80211/minstrel: use the new rate control API") inverted the condition 'if (msr->sample_limit != 0)' to 'if (!msr->sample_limit != 0)'. But it is confusing both to people and compilers (gcc5): net/mac80211/rc80211_minstrel.c: In function 'minstrel_get_rate': net/mac80211/rc80211_minstrel.c:376:26: warning: logical not is only applied to the left hand side of comparison if (!msr->sample_limit != 0) ^ Let there be only 'if (!msr->sample_limit)'. Fixes: 06d961a8e210 ("mac80211/minstrel: use the new rate control API") Signed-off-by: Jiri Slaby Signed-off-by: Johannes Berg --- net/mac80211/rc80211_minstrel.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/mac80211/rc80211_minstrel.c b/net/mac80211/rc80211_minstrel.c index 7c86a002df95..ef6e8a6c4253 100644 --- a/net/mac80211/rc80211_minstrel.c +++ b/net/mac80211/rc80211_minstrel.c @@ -373,7 +373,7 @@ minstrel_get_rate(void *priv, struct ieee80211_sta *sta, rate++; mi->sample_deferred++; } else { - if (!msr->sample_limit != 0) + if (!msr->sample_limit) return; mi->sample_packets++; -- cgit v1.2.3-59-g8ed1b From 4e10fd5b4a7f4100007147558c304da3e73b25cf Mon Sep 17 00:00:00 2001 From: Sasha Levin Date: Tue, 24 Feb 2015 14:14:35 -0500 Subject: rtnetlink: avoid 0 sized arrays Arrays (when not in a struct) "shall have a value greater than zero". GCC complains when it's not the case here. Fixes: ba7d49b1f0 ("rtnetlink: provide api for getting and setting slave info") Signed-off-by: Sasha Levin Signed-off-by: David S. Miller --- net/core/rtnetlink.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/core/rtnetlink.c b/net/core/rtnetlink.c index ab293a3066b3..1385de0fa080 100644 --- a/net/core/rtnetlink.c +++ b/net/core/rtnetlink.c @@ -2012,8 +2012,8 @@ replay: } if (1) { - struct nlattr *attr[ops ? ops->maxtype + 1 : 0]; - struct nlattr *slave_attr[m_ops ? m_ops->slave_maxtype + 1 : 0]; + struct nlattr *attr[ops ? ops->maxtype + 1 : 1]; + struct nlattr *slave_attr[m_ops ? m_ops->slave_maxtype + 1 : 1]; struct nlattr **data = NULL; struct nlattr **slave_data = NULL; struct net *dest_net, *link_net = NULL; -- cgit v1.2.3-59-g8ed1b From 41a50d621a321b4c15273cc1b5ed41437f4acdfb Mon Sep 17 00:00:00 2001 From: Alexander Drozdov Date: Tue, 24 Feb 2015 08:18:28 +0300 Subject: af_packet: don't pass empty blocks for PACKET_V3 Before da413eec729d ("packet: Fixed TPACKET V3 to signal poll when block is closed rather than every packet") poll listening for an af_packet socket was not signaled if there was no packets to process. After the patch poll is signaled evety time when block retire timer expires. That happens because af_packet closes the current block on timeout even if the block is empty. Passing empty blocks to the user not only wastes CPU but also wastes ring buffer space increasing probability of packets dropping on small timeouts. Signed-off-by: Alexander Drozdov Cc: Dan Collins Cc: Willem de Bruijn Cc: Guy Harris Signed-off-by: David S. Miller --- net/packet/af_packet.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) diff --git a/net/packet/af_packet.c b/net/packet/af_packet.c index 99fc628f7372..5bf1e968a728 100644 --- a/net/packet/af_packet.c +++ b/net/packet/af_packet.c @@ -698,6 +698,10 @@ static void prb_retire_rx_blk_timer_expired(unsigned long data) if (pkc->last_kactive_blk_num == pkc->kactive_blk_num) { if (!frozen) { + if (!BLOCK_NUM_PKTS(pbd)) { + /* An empty block. Just refresh the timer. */ + goto refresh_timer; + } prb_retire_current_block(pkc, po, TP_STATUS_BLK_TMO); if (!prb_dispatch_next_block(pkc, po)) goto refresh_timer; @@ -798,7 +802,11 @@ static void prb_close_block(struct tpacket_kbdq_core *pkc1, h1->ts_last_pkt.ts_sec = last_pkt->tp_sec; h1->ts_last_pkt.ts_nsec = last_pkt->tp_nsec; } else { - /* Ok, we tmo'd - so get the current time */ + /* Ok, we tmo'd - so get the current time. + * + * It shouldn't really happen as we don't close empty + * blocks. See prb_retire_rx_blk_timer_expired(). + */ struct timespec ts; getnstimeofday(&ts); h1->ts_last_pkt.ts_sec = ts.tv_sec; -- cgit v1.2.3-59-g8ed1b From 7fbb9d8415d4a51cf542e87cf3a717a9f7e6aedc Mon Sep 17 00:00:00 2001 From: David Vrabel Date: Tue, 24 Feb 2015 11:17:59 +0000 Subject: xen-netback: release pending index before pushing Tx responses If the pending indexes are released /after/ pushing the Tx response then a stale pending index may be used if a new Tx request is immediately pushed by the frontend. The may cause various WARNINGs or BUGs if the stale pending index is actually still in use. Fix this by releasing the pending index before pushing the Tx response. The full barrier for the pending ring update is not required since the the Tx response push already has a suitable write barrier. Signed-off-by: David Vrabel Reviewed-by: Wei Liu Signed-off-by: David S. Miller --- drivers/net/xen-netback/netback.c | 29 +++++++++++++++++++++-------- 1 file changed, 21 insertions(+), 8 deletions(-) diff --git a/drivers/net/xen-netback/netback.c b/drivers/net/xen-netback/netback.c index f7a31d2cb3f1..c4d68d768408 100644 --- a/drivers/net/xen-netback/netback.c +++ b/drivers/net/xen-netback/netback.c @@ -655,9 +655,15 @@ static void xenvif_tx_err(struct xenvif_queue *queue, unsigned long flags; do { + int notify; + spin_lock_irqsave(&queue->response_lock, flags); make_tx_response(queue, txp, XEN_NETIF_RSP_ERROR); + RING_PUSH_RESPONSES_AND_CHECK_NOTIFY(&queue->tx, notify); spin_unlock_irqrestore(&queue->response_lock, flags); + if (notify) + notify_remote_via_irq(queue->tx_irq); + if (cons == end) break; txp = RING_GET_REQUEST(&queue->tx, cons++); @@ -1649,17 +1655,28 @@ static void xenvif_idx_release(struct xenvif_queue *queue, u16 pending_idx, { struct pending_tx_info *pending_tx_info; pending_ring_idx_t index; + int notify; unsigned long flags; pending_tx_info = &queue->pending_tx_info[pending_idx]; + spin_lock_irqsave(&queue->response_lock, flags); + make_tx_response(queue, &pending_tx_info->req, status); - index = pending_index(queue->pending_prod); + + /* Release the pending index before pusing the Tx response so + * its available before a new Tx request is pushed by the + * frontend. + */ + index = pending_index(queue->pending_prod++); queue->pending_ring[index] = pending_idx; - /* TX shouldn't use the index before we give it back here */ - mb(); - queue->pending_prod++; + + RING_PUSH_RESPONSES_AND_CHECK_NOTIFY(&queue->tx, notify); + spin_unlock_irqrestore(&queue->response_lock, flags); + + if (notify) + notify_remote_via_irq(queue->tx_irq); } @@ -1669,7 +1686,6 @@ static void make_tx_response(struct xenvif_queue *queue, { RING_IDX i = queue->tx.rsp_prod_pvt; struct xen_netif_tx_response *resp; - int notify; resp = RING_GET_RESPONSE(&queue->tx, i); resp->id = txp->id; @@ -1679,9 +1695,6 @@ static void make_tx_response(struct xenvif_queue *queue, RING_GET_RESPONSE(&queue->tx, ++i)->status = XEN_NETIF_RSP_NULL; queue->tx.rsp_prod_pvt = ++i; - RING_PUSH_RESPONSES_AND_CHECK_NOTIFY(&queue->tx, notify); - if (notify) - notify_remote_via_irq(queue->tx_irq); } static struct xen_netif_rx_response *make_rx_response(struct xenvif_queue *queue, -- cgit v1.2.3-59-g8ed1b From 5c2d2b148b35a995f0c0e76a3a37902ec98f164c Mon Sep 17 00:00:00 2001 From: Yannick Guerrini Date: Tue, 24 Feb 2015 13:03:51 +0100 Subject: r8169: Fix trivial typo in rtl_check_firmware Change 'firwmare' to 'firmware' Signed-off-by: Yannick Guerrini Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index b1560927abd4..c70ab40d8698 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -2561,7 +2561,7 @@ static int rtl_check_firmware(struct rtl8169_private *tp, struct rtl_fw *rtl_fw) int rc = -EINVAL; if (!rtl_fw_format_ok(tp, rtl_fw)) { - netif_err(tp, ifup, dev, "invalid firwmare\n"); + netif_err(tp, ifup, dev, "invalid firmware\n"); goto out; } -- cgit v1.2.3-59-g8ed1b From d1901ef099c38afd11add4cfb3312c02ef21ec4a Mon Sep 17 00:00:00 2001 From: Tomáš Hodek Date: Mon, 23 Feb 2015 11:00:38 +1100 Subject: md/raid1: fix read balance when a drive is write-mostly. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When a drive is marked write-mostly it should only be the target of reads if there is no other option. This behaviour was broken by commit 9dedf60313fa4dddfd5b9b226a0ef12a512bf9dc md/raid1: read balance chooses idlest disk for SSD which causes a write-mostly device to be *preferred* is some cases. Restore correct behaviour by checking and setting best_dist_disk and best_pending_disk rather than best_disk. We only need to test one of these as they are both changed from -1 or >=0 at the same time. As we leave min_pending and best_dist unchanged, any non-write-mostly device will appear better than the write-mostly device. Reported-by: Tomáš Hodek Reported-by: Dark Penguin Signed-off-by: NeilBrown Link: http://marc.info/?l=linux-raid&m=135982797322422 Fixes: 9dedf60313fa4dddfd5b9b226a0ef12a512bf9dc Cc: stable@vger.kernel.org (3.6+) --- drivers/md/raid1.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c index 4153da5d4011..d34e238afa54 100644 --- a/drivers/md/raid1.c +++ b/drivers/md/raid1.c @@ -560,7 +560,7 @@ static int read_balance(struct r1conf *conf, struct r1bio *r1_bio, int *max_sect if (test_bit(WriteMostly, &rdev->flags)) { /* Don't balance among write-mostly, just * use the first as a last resort */ - if (best_disk < 0) { + if (best_dist_disk < 0) { if (is_badblock(rdev, this_sector, sectors, &first_bad, &bad_sectors)) { if (first_bad < this_sector) @@ -569,7 +569,8 @@ static int read_balance(struct r1conf *conf, struct r1bio *r1_bio, int *max_sect best_good_sectors = first_bad - this_sector; } else best_good_sectors = sectors; - best_disk = disk; + best_dist_disk = disk; + best_pending_disk = disk; } continue; } -- cgit v1.2.3-59-g8ed1b From 16d9cfab930bb6f4946cff8ba7429701fd15b414 Mon Sep 17 00:00:00 2001 From: Eric Mei Date: Tue, 6 Jan 2015 09:35:02 -0800 Subject: raid5: check faulty flag for array status during recovery. When we have more than 1 drive failure, it's possible we start rebuild one drive while leaving another faulty drive in array. To determine whether array will be optimal after building, current code only check whether a drive is missing, which could potentially lead to data corruption. This patch is to add checking Faulty flag. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index e75d48c0421a..cd2f96b2c572 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -5121,12 +5121,17 @@ static inline sector_t sync_request(struct mddev *mddev, sector_t sector_nr, int schedule_timeout_uninterruptible(1); } /* Need to check if array will still be degraded after recovery/resync - * We don't need to check the 'failed' flag as when that gets set, - * recovery aborts. + * Note in case of > 1 drive failures it's possible we're rebuilding + * one drive while leaving another faulty drive in array. */ - for (i = 0; i < conf->raid_disks; i++) - if (conf->disks[i].rdev == NULL) + rcu_read_lock(); + for (i = 0; i < conf->raid_disks; i++) { + struct md_rdev *rdev = ACCESS_ONCE(conf->disks[i].rdev); + + if (rdev == NULL || test_bit(Faulty, &rdev->flags)) still_degraded = 1; + } + rcu_read_unlock(); bitmap_start_sync(mddev->bitmap, sector_nr, &sync_blocks, still_degraded); -- cgit v1.2.3-59-g8ed1b From 750f199ee8b578062341e6ddfe36c59ac8ff2dcb Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 30 Sep 2014 08:53:05 +1000 Subject: md: mark some attributes as pre-alloc Since __ATTR_PREALLOC was introduced in v3.19-rc1~78^2~18 it can now be used by md. This ensure that writing to these sysfs attributes will never block due to a memory allocation. Such blocking could become a deadlock if mdmon is trying to reconfigure an array after a failure prior to re-enabling writes. Signed-off-by: NeilBrown --- drivers/md/md.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index c8d2bac4e28b..cadf9cc02b25 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -2555,7 +2555,7 @@ state_store(struct md_rdev *rdev, const char *buf, size_t len) return err ? err : len; } static struct rdev_sysfs_entry rdev_state = -__ATTR(state, S_IRUGO|S_IWUSR, state_show, state_store); +__ATTR_PREALLOC(state, S_IRUGO|S_IWUSR, state_show, state_store); static ssize_t errors_show(struct md_rdev *rdev, char *page) @@ -3638,7 +3638,8 @@ resync_start_store(struct mddev *mddev, const char *buf, size_t len) return err ?: len; } static struct md_sysfs_entry md_resync_start = -__ATTR(resync_start, S_IRUGO|S_IWUSR, resync_start_show, resync_start_store); +__ATTR_PREALLOC(resync_start, S_IRUGO|S_IWUSR, + resync_start_show, resync_start_store); /* * The array state can be: @@ -3851,7 +3852,7 @@ array_state_store(struct mddev *mddev, const char *buf, size_t len) return err ?: len; } static struct md_sysfs_entry md_array_state = -__ATTR(array_state, S_IRUGO|S_IWUSR, array_state_show, array_state_store); +__ATTR_PREALLOC(array_state, S_IRUGO|S_IWUSR, array_state_show, array_state_store); static ssize_t max_corrected_read_errors_show(struct mddev *mddev, char *page) { @@ -4101,7 +4102,7 @@ out_unlock: } static struct md_sysfs_entry md_metadata = -__ATTR(metadata_version, S_IRUGO|S_IWUSR, metadata_show, metadata_store); +__ATTR_PREALLOC(metadata_version, S_IRUGO|S_IWUSR, metadata_show, metadata_store); static ssize_t action_show(struct mddev *mddev, char *page) @@ -4189,7 +4190,7 @@ action_store(struct mddev *mddev, const char *page, size_t len) } static struct md_sysfs_entry md_scan_mode = -__ATTR(sync_action, S_IRUGO|S_IWUSR, action_show, action_store); +__ATTR_PREALLOC(sync_action, S_IRUGO|S_IWUSR, action_show, action_store); static ssize_t last_sync_action_show(struct mddev *mddev, char *page) @@ -4335,7 +4336,8 @@ sync_completed_show(struct mddev *mddev, char *page) return sprintf(page, "%llu / %llu\n", resync, max_sectors); } -static struct md_sysfs_entry md_sync_completed = __ATTR_RO(sync_completed); +static struct md_sysfs_entry md_sync_completed = + __ATTR_PREALLOC(sync_completed, S_IRUGO, sync_completed_show, NULL); static ssize_t min_sync_show(struct mddev *mddev, char *page) -- cgit v1.2.3-59-g8ed1b From 2a559a8bdeae853b6a8abb477c88875e1d4de591 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Mon, 23 Feb 2015 11:34:10 +0000 Subject: eCryptfs: ensure copy to crypt_stat->cipher does not overrun The patch 237fead61998: "[PATCH] ecryptfs: fs/Makefile and fs/Kconfig" from Oct 4, 2006, leads to the following static checker warning: fs/ecryptfs/crypto.c:846 ecryptfs_new_file_context() error: off-by-one overflow 'crypt_stat->cipher' size 32. rl = '0-32' There is a mismatch between the size of ecryptfs_crypt_stat.cipher and ecryptfs_mount_crypt_stat.global_default_cipher_name causing the copy of the cipher name to cause a off-by-one string copy error. This fix ensures the space reserved for this string is the same size including the trailing zero at the end throughout ecryptfs. This fix avoids increasing the size of ecryptfs_crypt_stat.cipher and also ecryptfs_parse_tag_70_packet_silly_stack.cipher_string and instead reduces the of ECRYPTFS_MAX_CIPHER_NAME_SIZE to 31 and includes the + 1 for the end of string terminator. NOTE: An overflow is not possible in practice since the value copied into global_default_cipher_name is validated by ecryptfs_code_for_cipher_string() at mount time. None of the allowed cipher strings are long enough to cause the potential buffer overflow fixed by this patch. Signed-off-by: Colin Ian King Reported-by: Dan Carpenter [tyhicks: Added the NOTE about the overflow not being triggerable] Signed-off-by: Tyler Hicks --- fs/ecryptfs/ecryptfs_kernel.h | 4 ++-- fs/ecryptfs/keystore.c | 2 +- fs/ecryptfs/main.c | 2 +- 3 files changed, 4 insertions(+), 4 deletions(-) diff --git a/fs/ecryptfs/ecryptfs_kernel.h b/fs/ecryptfs/ecryptfs_kernel.h index 90d1882b306f..5ba029e627cc 100644 --- a/fs/ecryptfs/ecryptfs_kernel.h +++ b/fs/ecryptfs/ecryptfs_kernel.h @@ -124,7 +124,7 @@ ecryptfs_get_key_payload_data(struct key *key) } #define ECRYPTFS_MAX_KEYSET_SIZE 1024 -#define ECRYPTFS_MAX_CIPHER_NAME_SIZE 32 +#define ECRYPTFS_MAX_CIPHER_NAME_SIZE 31 #define ECRYPTFS_MAX_NUM_ENC_KEYS 64 #define ECRYPTFS_MAX_IV_BYTES 16 /* 128 bits */ #define ECRYPTFS_SALT_BYTES 2 @@ -237,7 +237,7 @@ struct ecryptfs_crypt_stat { struct crypto_ablkcipher *tfm; struct crypto_hash *hash_tfm; /* Crypto context for generating * the initialization vectors */ - unsigned char cipher[ECRYPTFS_MAX_CIPHER_NAME_SIZE]; + unsigned char cipher[ECRYPTFS_MAX_CIPHER_NAME_SIZE + 1]; unsigned char key[ECRYPTFS_MAX_KEY_BYTES]; unsigned char root_iv[ECRYPTFS_MAX_IV_BYTES]; struct list_head keysig_list; diff --git a/fs/ecryptfs/keystore.c b/fs/ecryptfs/keystore.c index 917bd5c9776a..6bd67e2011f0 100644 --- a/fs/ecryptfs/keystore.c +++ b/fs/ecryptfs/keystore.c @@ -891,7 +891,7 @@ struct ecryptfs_parse_tag_70_packet_silly_stack { struct blkcipher_desc desc; char fnek_sig_hex[ECRYPTFS_SIG_SIZE_HEX + 1]; char iv[ECRYPTFS_MAX_IV_BYTES]; - char cipher_string[ECRYPTFS_MAX_CIPHER_NAME_SIZE]; + char cipher_string[ECRYPTFS_MAX_CIPHER_NAME_SIZE + 1]; }; /** diff --git a/fs/ecryptfs/main.c b/fs/ecryptfs/main.c index 1895d60f4122..c095d3264259 100644 --- a/fs/ecryptfs/main.c +++ b/fs/ecryptfs/main.c @@ -407,7 +407,7 @@ static int ecryptfs_parse_options(struct ecryptfs_sb_info *sbi, char *options, if (!cipher_name_set) { int cipher_name_len = strlen(ECRYPTFS_DEFAULT_CIPHER); - BUG_ON(cipher_name_len >= ECRYPTFS_MAX_CIPHER_NAME_SIZE); + BUG_ON(cipher_name_len > ECRYPTFS_MAX_CIPHER_NAME_SIZE); strcpy(mount_crypt_stat->global_default_cipher_name, ECRYPTFS_DEFAULT_CIPHER); } -- cgit v1.2.3-59-g8ed1b From de5d0ad506cb10ab143e2ffb9def7607e3671f83 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Wed, 25 Feb 2015 07:53:31 +0100 Subject: ALSA: hda - Disable runtime PM for Panther Point again This is essentially a partial revert of the commit [b1920c21102a: 'ALSA: hda - Enable runtime PM on Panther Point']. There was a bug report showing the HD-audio bus hang during runtime PM on HP Spectre XT. Reported-by: Dang Sananikone Cc: Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_intel.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 36d2f20db7a4..4ca3d5d02436 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -1966,7 +1966,7 @@ static const struct pci_device_id azx_ids[] = { .driver_data = AZX_DRIVER_PCH | AZX_DCAPS_INTEL_PCH_NOPM }, /* Panther Point */ { PCI_DEVICE(0x8086, 0x1e20), - .driver_data = AZX_DRIVER_PCH | AZX_DCAPS_INTEL_PCH }, + .driver_data = AZX_DRIVER_PCH | AZX_DCAPS_INTEL_PCH_NOPM }, /* Lynx Point */ { PCI_DEVICE(0x8086, 0x8c20), .driver_data = AZX_DRIVER_PCH | AZX_DCAPS_INTEL_PCH }, -- cgit v1.2.3-59-g8ed1b From 62e537f8d568347bbe4e00d7803a838750cdc618 Mon Sep 17 00:00:00 2001 From: Rodrigo Vivi Date: Tue, 24 Feb 2015 13:37:54 -0800 Subject: drm/i915: Fix frontbuffer false positve. This return 0 without setting atomic bits on fb == crtc->cursor->fb where causing frontbuffer false positives. According to Daniel: The original regression seems to have been introduced in the original check/commit split: commit 757f9a3e5b8a812af0c213099a5b31cb423f4d3c Author: Gustavo Padovan Date: Wed Sep 24 14:20:24 2014 -0300 drm/i915: move check of intel_crtc_cursor_set_obj() out Which already cause other trouble, resulting in the check getting moved in commit e391ea882b1a04fb3f559287ac694652a3cd9da9 Author: Gustavo Padovan Date: Wed Sep 24 14:20:25 2014 -0300 drm/i915: Fix not checking cursor and object sizes The frontbuffer tracking itself only was broken when we shifted it into the check/commit logic with: commit 32b7eeec4d1e861230b09d437e95d76c86ff4a68 Author: Matt Roper Date: Wed Dec 24 07:59:06 2014 -0800 drm/i915: Refactor work that can sleep out of commit (v7) v2: When putting more debug prints I notice the solution was simpler than I thought. AMS design is solid, just this return was wrong. Sorry for the noise. v3: Remove the entire chunck that would probably be removed by gcc anyway. (by Daniel) Cc: Jani Nikula Cc: Gustavo Padovan Cc: Matt Roper Signed-off-by: Rodrigo Vivi Reviewed-by: Matt Roper Reviewed-by: Daniel Vetter Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/intel_display.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index bf19a5cce4a8..3117679299a6 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -12197,9 +12197,6 @@ intel_check_cursor_plane(struct drm_plane *plane, return -ENOMEM; } - if (fb == crtc->cursor->fb) - return 0; - /* we only need to pin inside GTT if cursor is non-phy */ mutex_lock(&dev->struct_mutex); if (!INTEL_INFO(dev)->cursor_needs_physical && obj->tiling_mode) { -- cgit v1.2.3-59-g8ed1b From a8b1b9fc927400045fb7631d5b12093aaf5d939d Mon Sep 17 00:00:00 2001 From: Daniel Lezcano Date: Mon, 23 Feb 2015 19:54:16 +0100 Subject: clockevents: asm9260: Fix compilation error with sparc/sparc64 allyesconfig The Kconfig options for the asm9260 timer is wrong as it can be selected by another platform with allyes config and thus leading to a compilation failure as some non arch related code is pulled by the compilation. Fix this by having the platform Kconfig to select the timer as it is done for the others drivers. Signed-off-by: Daniel Lezcano Acked-by: Guenter Roeck Acked-by: Oleksij Rempel Conflicts: drivers/clocksource/Kconfig --- arch/arm/mach-asm9260/Kconfig | 2 ++ drivers/clocksource/Kconfig | 16 +++++----------- 2 files changed, 7 insertions(+), 11 deletions(-) diff --git a/arch/arm/mach-asm9260/Kconfig b/arch/arm/mach-asm9260/Kconfig index 8423be76080e..52241207a82a 100644 --- a/arch/arm/mach-asm9260/Kconfig +++ b/arch/arm/mach-asm9260/Kconfig @@ -2,5 +2,7 @@ config MACH_ASM9260 bool "Alphascale ASM9260" depends on ARCH_MULTI_V5 select CPU_ARM926T + select ASM9260_TIMER + select GENERIC_CLOCKEVENTS help Support for Alphascale ASM9260 based platform. diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig index 1c2506f68122..68161f7a07d6 100644 --- a/drivers/clocksource/Kconfig +++ b/drivers/clocksource/Kconfig @@ -63,6 +63,11 @@ config VT8500_TIMER config CADENCE_TTC_TIMER bool +config ASM9260_TIMER + bool + select CLKSRC_MMIO + select CLKSRC_OF + config CLKSRC_NOMADIK_MTU bool depends on (ARCH_NOMADIK || ARCH_U8500) @@ -245,15 +250,4 @@ config CLKSRC_PXA help This enables OST0 support available on PXA and SA-11x0 platforms. - -config ASM9260_TIMER - bool "Alphascale ASM9260 timer driver" - depends on GENERIC_CLOCKEVENTS - select CLKSRC_MMIO - select CLKSRC_OF - default y if MACH_ASM9260 - help - This enables build of a clocksource and clockevent driver for - the 32-bit System Timer hardware available on a Alphascale ASM9260. - endmenu -- cgit v1.2.3-59-g8ed1b From d4a19eb3b15a4ba98f627182f48d5bc0cffae670 Mon Sep 17 00:00:00 2001 From: Matthias Brugger Date: Thu, 19 Feb 2015 11:41:33 +0100 Subject: clocksource: mtk: Fix race conditions in probe code We have two race conditions in the probe code which could lead to a null pointer dereference in the interrupt handler. The interrupt handler accesses the clockevent device, which may not yet be registered. First race condition happens when the interrupt handler gets registered before the interrupts get disabled. The second race condition happens when the interrupts get enabled, but the clockevent device is not yet registered. Fix that by disabling the interrupts before we register the interrupt and enable the interrupts after the clockevent device got registered. Reported-by: Gongbae Park Signed-off-by: Matthias Brugger Cc: stable@vger.kernel.org Signed-off-by: Daniel Lezcano --- drivers/clocksource/mtk_timer.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/clocksource/mtk_timer.c b/drivers/clocksource/mtk_timer.c index 32a3d25795d3..68ab42356d0e 100644 --- a/drivers/clocksource/mtk_timer.c +++ b/drivers/clocksource/mtk_timer.c @@ -224,6 +224,8 @@ static void __init mtk_timer_init(struct device_node *node) } rate = clk_get_rate(clk); + mtk_timer_global_reset(evt); + if (request_irq(evt->dev.irq, mtk_timer_interrupt, IRQF_TIMER | IRQF_IRQPOLL, "mtk_timer", evt)) { pr_warn("failed to setup irq %d\n", evt->dev.irq); @@ -232,8 +234,6 @@ static void __init mtk_timer_init(struct device_node *node) evt->ticks_per_jiffy = DIV_ROUND_UP(rate, HZ); - mtk_timer_global_reset(evt); - /* Configure clock source */ mtk_timer_setup(evt, GPT_CLK_SRC, TIMER_CTRL_OP_FREERUN); clocksource_mmio_init(evt->gpt_base + TIMER_CNT_REG(GPT_CLK_SRC), @@ -241,10 +241,11 @@ static void __init mtk_timer_init(struct device_node *node) /* Configure clock event */ mtk_timer_setup(evt, GPT_CLK_EVT, TIMER_CTRL_OP_REPEAT); - mtk_timer_enable_irq(evt, GPT_CLK_EVT); - clockevents_config_and_register(&evt->dev, rate, 0x3, 0xffffffff); + + mtk_timer_enable_irq(evt, GPT_CLK_EVT); + return; err_clk_disable: -- cgit v1.2.3-59-g8ed1b From 6f2116ebe24f9f0f0d90ad17e405ea181f2499eb Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Sat, 31 Jan 2015 23:40:40 +0100 Subject: clocksource: pxa: Fix section mismatch As pxa_timer_common_init() is only called in init context, mark it as such, and quiesce the compiler warnings : WARNING: vmlinux.o(.text.unlikely+0x45d4): Section mismatch in reference from the function pxa_timer_common_init() to the function .init.text:sched_clock_register() WARNING: vmlinux.o(.text.unlikely+0x4610): Section mismatch in reference from the function pxa_timer_common_init() to the function .init.text:clocksource_mmio_init() Signed-off-by: Robert Jarzmik Signed-off-by: Daniel Lezcano --- drivers/clocksource/pxa_timer.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/clocksource/pxa_timer.c b/drivers/clocksource/pxa_timer.c index 941f3f344e08..d9438af2bbd6 100644 --- a/drivers/clocksource/pxa_timer.c +++ b/drivers/clocksource/pxa_timer.c @@ -163,7 +163,7 @@ static struct irqaction pxa_ost0_irq = { .dev_id = &ckevt_pxa_osmr0, }; -static void pxa_timer_common_init(int irq, unsigned long clock_tick_rate) +static void __init pxa_timer_common_init(int irq, unsigned long clock_tick_rate) { timer_writel(0, OIER); timer_writel(OSSR_M0 | OSSR_M1 | OSSR_M2 | OSSR_M3, OSSR); -- cgit v1.2.3-59-g8ed1b From 8eb733829cd17b9b66971f08110df7224d391d65 Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Wed, 11 Feb 2015 11:24:05 -0500 Subject: perf tools: Define _GNU_SOURCE on pthread_attr_setaffinity_np feature check The man page for pthread_attr_set_affinity_np states that _GNU_SOURCE must be defined before pthread.h is included in order to get the proper function declaration. Define this in the Makefile. Without this defined, the feature check fails on a Fedora system with gcc5 and then the perf build later fails with conflicting prototypes for the function. Signed-off-by: Josh Boyer Cc: Jiri Olsa Cc: Peter Zijlstra Cc: Vineet Gupta Link: http://lkml.kernel.org/r/20150211162404.GA15522@hansolo.redhat.com Signed-off-by: Arnaldo Carvalho de Melo --- tools/perf/config/feature-checks/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/config/feature-checks/Makefile b/tools/perf/config/feature-checks/Makefile index 42ac05aaf8ac..b32ff3372514 100644 --- a/tools/perf/config/feature-checks/Makefile +++ b/tools/perf/config/feature-checks/Makefile @@ -49,7 +49,7 @@ test-hello.bin: $(BUILD) test-pthread-attr-setaffinity-np.bin: - $(BUILD) -Werror -lpthread + $(BUILD) -D_GNU_SOURCE -Werror -lpthread test-stackprotector-all.bin: $(BUILD) -Werror -fstack-protector-all -- cgit v1.2.3-59-g8ed1b From 95a09cfa3cdf94231ce511f1697754482b918d39 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Tue, 24 Feb 2015 12:46:06 +0200 Subject: perf tools: Fix pthread_attr_setaffinity_np build error MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Feature detection for pthread_attr_setaffinity_np was failing, producing this error: In file included from bench/futex-hash.c:17:0: bench/futex.h:73:19: error: conflicting types for ‘pthread_attr_setaffinity_np’ static inline int pthread_attr_setaffinity_np(pthread_attr_t *attr, ^ In file included from bench/futex.h:72:0, from bench/futex-hash.c:17: /usr/include/pthread.h:407:12: note: previous declaration of ‘pthread_attr_setaffinity_np’ was here extern int pthread_attr_setaffinity_np (pthread_attr_t *__attr, ^ make[3]: *** [bench/futex-hash.o] Error 1 make[2]: *** [bench] Error 2 make[2]: *** Waiting for unfinished jobs.... This was because compiling test-pthread-attr-setaffinity-np.c failed due to the function arguments: test-pthread-attr-setaffinity-np.c: In function ‘main’: test-pthread-attr-setaffinity-np.c:11:2: warning: null argument where non-null required (argument 3) [-Wnonnull] ret = pthread_attr_setaffinity_np(&thread_attr, 0, NULL); ^ So fix the arguments. Signed-off-by: Adrian Hunter Tested-by: Stephane Eranian Cc: Jiri Olsa Link: http://lkml.kernel.org/r/1424774766-24194-1-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo --- tools/perf/config/feature-checks/test-pthread-attr-setaffinity-np.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/tools/perf/config/feature-checks/test-pthread-attr-setaffinity-np.c b/tools/perf/config/feature-checks/test-pthread-attr-setaffinity-np.c index 0a0d3ecb4e8a..2b81b72eca23 100644 --- a/tools/perf/config/feature-checks/test-pthread-attr-setaffinity-np.c +++ b/tools/perf/config/feature-checks/test-pthread-attr-setaffinity-np.c @@ -5,10 +5,11 @@ int main(void) { int ret = 0; pthread_attr_t thread_attr; + cpu_set_t cs; pthread_attr_init(&thread_attr); /* don't care abt exact args, just the API itself in libpthread */ - ret = pthread_attr_setaffinity_np(&thread_attr, 0, NULL); + ret = pthread_attr_setaffinity_np(&thread_attr, sizeof(cs), &cs); return ret; } -- cgit v1.2.3-59-g8ed1b From 7934d69abfa98392433c03136025b71972851733 Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Wed, 21 Jan 2015 12:02:30 +0000 Subject: arm64: Add L2 cache topology to ARM Ltd boards/models Commit 5d425c18653731af6 ("arm64: kernel: add support for cpu cache information") adds cacheinfo support for ARM64. Since there's no architectural way of detecting the cpus that share particular cache, device tree can be used and the core cacheinfo already supports the same. This patch adds the L2 cache topology on Juno board, FVP/RTSM and foundation models. Signed-off-by: Sudeep Holla Cc: Mark Rutland Cc: Liviu Dudau Cc: Lorenzo Pieralisi Signed-off-by: Arnd Bergmann --- arch/arm64/boot/dts/arm/foundation-v8.dts | 8 ++++++++ arch/arm64/boot/dts/arm/juno.dts | 14 ++++++++++++++ arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts | 8 ++++++++ 3 files changed, 30 insertions(+) diff --git a/arch/arm64/boot/dts/arm/foundation-v8.dts b/arch/arm64/boot/dts/arm/foundation-v8.dts index 27f32962e55c..4eac8dcea423 100644 --- a/arch/arm64/boot/dts/arm/foundation-v8.dts +++ b/arch/arm64/boot/dts/arm/foundation-v8.dts @@ -34,6 +34,7 @@ reg = <0x0 0x0>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; }; cpu@1 { device_type = "cpu"; @@ -41,6 +42,7 @@ reg = <0x0 0x1>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; }; cpu@2 { device_type = "cpu"; @@ -48,6 +50,7 @@ reg = <0x0 0x2>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; }; cpu@3 { device_type = "cpu"; @@ -55,6 +58,11 @@ reg = <0x0 0x3>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache0 { + compatible = "cache"; }; }; diff --git a/arch/arm64/boot/dts/arm/juno.dts b/arch/arm64/boot/dts/arm/juno.dts index d429129ecb3d..133ee59de2d7 100644 --- a/arch/arm64/boot/dts/arm/juno.dts +++ b/arch/arm64/boot/dts/arm/juno.dts @@ -39,6 +39,7 @@ reg = <0x0 0x0>; device_type = "cpu"; enable-method = "psci"; + next-level-cache = <&A57_L2>; }; A57_1: cpu@1 { @@ -46,6 +47,7 @@ reg = <0x0 0x1>; device_type = "cpu"; enable-method = "psci"; + next-level-cache = <&A57_L2>; }; A53_0: cpu@100 { @@ -53,6 +55,7 @@ reg = <0x0 0x100>; device_type = "cpu"; enable-method = "psci"; + next-level-cache = <&A53_L2>; }; A53_1: cpu@101 { @@ -60,6 +63,7 @@ reg = <0x0 0x101>; device_type = "cpu"; enable-method = "psci"; + next-level-cache = <&A53_L2>; }; A53_2: cpu@102 { @@ -67,6 +71,7 @@ reg = <0x0 0x102>; device_type = "cpu"; enable-method = "psci"; + next-level-cache = <&A53_L2>; }; A53_3: cpu@103 { @@ -74,6 +79,15 @@ reg = <0x0 0x103>; device_type = "cpu"; enable-method = "psci"; + next-level-cache = <&A53_L2>; + }; + + A57_L2: l2-cache0 { + compatible = "cache"; + }; + + A53_L2: l2-cache1 { + compatible = "cache"; }; }; diff --git a/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts b/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts index efc59b3baf63..20addabbd127 100644 --- a/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts +++ b/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts @@ -37,6 +37,7 @@ reg = <0x0 0x0>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; }; cpu@1 { device_type = "cpu"; @@ -44,6 +45,7 @@ reg = <0x0 0x1>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; }; cpu@2 { device_type = "cpu"; @@ -51,6 +53,7 @@ reg = <0x0 0x2>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; }; cpu@3 { device_type = "cpu"; @@ -58,6 +61,11 @@ reg = <0x0 0x3>; enable-method = "spin-table"; cpu-release-addr = <0x0 0x8000fff8>; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache0 { + compatible = "cache"; }; }; -- cgit v1.2.3-59-g8ed1b From 48536c9195ae8c2a00fd8f400bac72ab613feaab Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Tue, 24 Feb 2015 13:20:59 +0200 Subject: perf tools: Fix probing for PERF_FLAG_FD_CLOEXEC flag Commit f6edb53c4993ffe92ce521fb449d1c146cea6ec2 converted the probe to a CPU wide event first (pid == -1). For kernels that do not support the PERF_FLAG_FD_CLOEXEC flag the probe fails with EINVAL. Since this errno is not handled pid is not reset to 0 and the subsequent use of pid = -1 as an argument brings in an additional failure path if perf_event_paranoid > 0: $ perf record -- sleep 1 perf_event_open(..., 0) failed unexpectedly with error 13 (Permission denied) [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.007 MB /tmp/perf.data (11 samples) ] Also, ensure the fd of the confirmation check is closed and comment why pid = -1 is used. Needs to go to 3.18 stable tree as well. Signed-off-by: Adrian Hunter Based-on-patch-by: David Ahern Acked-by: David Ahern Cc: David Ahern Link: http://lkml.kernel.org/r/54EC610C.8000403@intel.com Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Arnaldo Carvalho de Melo --- tools/perf/util/cloexec.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) diff --git a/tools/perf/util/cloexec.c b/tools/perf/util/cloexec.c index 47b78b3f0325..6da965bdbc2c 100644 --- a/tools/perf/util/cloexec.c +++ b/tools/perf/util/cloexec.c @@ -25,6 +25,10 @@ static int perf_flag_probe(void) if (cpu < 0) cpu = 0; + /* + * Using -1 for the pid is a workaround to avoid gratuitous jump label + * changes. + */ while (1) { /* check cloexec flag */ fd = sys_perf_event_open(&attr, pid, cpu, -1, @@ -47,16 +51,24 @@ static int perf_flag_probe(void) err, strerror_r(err, sbuf, sizeof(sbuf))); /* not supported, confirm error related to PERF_FLAG_FD_CLOEXEC */ - fd = sys_perf_event_open(&attr, pid, cpu, -1, 0); + while (1) { + fd = sys_perf_event_open(&attr, pid, cpu, -1, 0); + if (fd < 0 && pid == -1 && errno == EACCES) { + pid = 0; + continue; + } + break; + } err = errno; + if (fd >= 0) + close(fd); + if (WARN_ONCE(fd < 0 && err != EBUSY, "perf_event_open(..., 0) failed unexpectedly with error %d (%s)\n", err, strerror_r(err, sbuf, sizeof(sbuf)))) return -1; - close(fd); - return 0; } -- cgit v1.2.3-59-g8ed1b From a73b6c199a663d64a38198f547d5c5be42163193 Mon Sep 17 00:00:00 2001 From: David Ahern Date: Wed, 18 Feb 2015 19:03:18 -0500 Subject: perf top: Fix SIGBUS on sparc64 perf-top is terminating due to SIGBUS on sparc64. git bisect points to: commit 82396986032915c1572bfb74b224fcc2e4e8ba7c Author: Arnaldo Carvalho de Melo Date: Mon Sep 8 13:26:35 2014 -0300 perf evlist: Refcount mmaps We need to know how many fds are using a perf mmap via PERF_EVENT_IOC_SET_OUTPUT, so that we can know when to ditch an mmap, refcount it. This commit added 'int refcnt' to struct perf_mmap and the addition makes the event_copy element no longer 8-byte aligned. Fix by adding __attribute__((aligned(8))) to the event_copy struct member. Signed-off-by: David Ahern Link: http://lkml.kernel.org/r/1424304198-92028-1-git-send-email-david.ahern@oracle.com [ Switched from 'int pad;' to using __attribute__, David tested/acked that ] Signed-off-by: Arnaldo Carvalho de Melo --- tools/perf/util/evlist.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/util/evlist.h b/tools/perf/util/evlist.h index c94a9e03ecf1..e99a67632831 100644 --- a/tools/perf/util/evlist.h +++ b/tools/perf/util/evlist.h @@ -28,7 +28,7 @@ struct perf_mmap { int mask; int refcnt; unsigned int prev; - char event_copy[PERF_SAMPLE_MAX_SIZE]; + char event_copy[PERF_SAMPLE_MAX_SIZE] __attribute__((aligned(8))); }; struct perf_evlist { -- cgit v1.2.3-59-g8ed1b From e370a3d57664cd5e39c0b95d157ebc841b568409 Mon Sep 17 00:00:00 2001 From: David Ahern Date: Wed, 18 Feb 2015 19:33:37 -0500 Subject: perf symbols: Define EM_AARCH64 for older OSes 4886f2ca19f6f added an arm-64 check, but the EM_AARCH64 macro is not defined in older releases (e.g., RHEL6). Define if it is not defined. Signed-off-by: David Ahern Cc: Victor Kamensky Link: http://lkml.kernel.org/r/1424306017-96797-1-git-send-email-david.ahern@oracle.com Signed-off-by: Arnaldo Carvalho de Melo --- tools/perf/util/symbol-elf.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/tools/perf/util/symbol-elf.c b/tools/perf/util/symbol-elf.c index b24f9d8727a8..33b7a2aef713 100644 --- a/tools/perf/util/symbol-elf.c +++ b/tools/perf/util/symbol-elf.c @@ -11,6 +11,11 @@ #include #include "debug.h" +#ifndef EM_AARCH64 +#define EM_AARCH64 183 /* ARM 64 bit */ +#endif + + #ifdef HAVE_CPLUS_DEMANGLE_SUPPORT extern char *cplus_demangle(const char *, int); -- cgit v1.2.3-59-g8ed1b From 4861f87cd3d133f03e3b39b6650f4e12f1a9e421 Mon Sep 17 00:00:00 2001 From: David Ahern Date: Wed, 18 Feb 2015 19:37:02 -0500 Subject: perf tools: Make sparc64 arch point to sparc The recent build changes cause perf to not compile for sparc64 since the arch/sparc64/Build file does not exist: /home/dahern/kernels/linux.git/tools/build/Makefile.build:40: arch/sparc64/Build: No such file or directory Fix by converting the sparc64 RAW_ARCH to sparc ARCH -- similar to what is done for x86_64. Signed-off-by: David Ahern Cc: Jiri Olsa Link: http://lkml.kernel.org/r/1424306222-96843-1-git-send-email-david.ahern@oracle.com Signed-off-by: Arnaldo Carvalho de Melo --- tools/perf/config/Makefile.arch | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/tools/perf/config/Makefile.arch b/tools/perf/config/Makefile.arch index ff95a68741d1..ac8721ffa6c8 100644 --- a/tools/perf/config/Makefile.arch +++ b/tools/perf/config/Makefile.arch @@ -21,6 +21,10 @@ ifeq ($(RAW_ARCH),x86_64) endif endif +ifeq ($(RAW_ARCH),sparc64) + ARCH ?= sparc +endif + ARCH ?= $(RAW_ARCH) LP64 := $(shell echo __LP64__ | ${CC} ${CFLAGS} -E -x c - | tail -n 1) -- cgit v1.2.3-59-g8ed1b From 7a26f9ad1b5badfd0200ce2262ad696e2a6b7fbb Mon Sep 17 00:00:00 2001 From: "Nathan-J. Hirschauer" Date: Wed, 18 Feb 2015 02:01:19 +0100 Subject: drm/radeon: enable native backlight control on old macs Commit b7bc596ebbe0 ("drm/radeon: disable native backlight control on pre-r6xx asics (v2)") accidently broke backlight control on old mac laptops that use the on-GPU backlight controller. Signed-off-by: Nathan-J. Hirschauer Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/radeon_encoders.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/radeon/radeon_encoders.c b/drivers/gpu/drm/radeon/radeon_encoders.c index 6b670b0bc47b..3a297037cc17 100644 --- a/drivers/gpu/drm/radeon/radeon_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_encoders.c @@ -179,9 +179,12 @@ static void radeon_encoder_add_backlight(struct radeon_encoder *radeon_encoder, (rdev->pdev->subsystem_vendor == 0x1734) && (rdev->pdev->subsystem_device == 0x1107)) use_bl = false; +/* Older PPC macs use on-GPU backlight controller */ +#ifndef CONFIG_PPC_PMAC /* disable native backlight control on older asics */ else if (rdev->family < CHIP_R600) use_bl = false; +#endif else use_bl = true; } -- cgit v1.2.3-59-g8ed1b From 3d2d98ee1af0cf6eebfbd6bff4c17d3601ac1284 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 18 Feb 2015 01:05:30 -0500 Subject: drm/radeon: use drm_mode_vrefresh() rather than mode->vrefresh Just in case it hasn't been calculated for the mode. Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/r600_dpm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/r600_dpm.c b/drivers/gpu/drm/radeon/r600_dpm.c index 843b65f46ece..fa2154493cf1 100644 --- a/drivers/gpu/drm/radeon/r600_dpm.c +++ b/drivers/gpu/drm/radeon/r600_dpm.c @@ -188,7 +188,7 @@ u32 r600_dpm_get_vrefresh(struct radeon_device *rdev) list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) { radeon_crtc = to_radeon_crtc(crtc); if (crtc->enabled && radeon_crtc->enabled && radeon_crtc->hw_mode.clock) { - vrefresh = radeon_crtc->hw_mode.vrefresh; + vrefresh = drm_mode_vrefresh(&radeon_crtc->hw_mode); break; } } -- cgit v1.2.3-59-g8ed1b From 951caa6acf7121f88a9e8e04ef75bd0ac323a033 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 18 Feb 2015 00:59:45 -0500 Subject: drm/radeon: disable mclk switching with 120hz+ monitors These tend to be problematic even if the vblank period is long enough. This needs more investigation across a wider range of displays. Disable for now. bugs: https://bugs.freedesktop.org/show_bug.cgi?id=87796 https://bugs.freedesktop.org/show_bug.cgi?id=89198 Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/radeon_pm.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/gpu/drm/radeon/radeon_pm.c b/drivers/gpu/drm/radeon/radeon_pm.c index 9f758d39420d..33cf4108386d 100644 --- a/drivers/gpu/drm/radeon/radeon_pm.c +++ b/drivers/gpu/drm/radeon/radeon_pm.c @@ -852,6 +852,12 @@ static struct radeon_ps *radeon_dpm_pick_power_state(struct radeon_device *rdev, single_display = false; } + /* 120hz tends to be problematic even if they are under the + * vblank limit. + */ + if (single_display && (r600_dpm_get_vrefresh(rdev) >= 120)) + single_display = false; + /* certain older asics have a separare 3D performance state, * so try that first if the user selected performance */ -- cgit v1.2.3-59-g8ed1b From e1b4e722f7b401bdf90f2ac397b89c20d096eb04 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 18 Feb 2015 10:15:10 -0500 Subject: drm/radeon: dump full IB if we hit a packet error Dump the whole IB if we run into an invalid packet. This makes things much easier to debug. bug: https://bugs.freedesktop.org/show_bug.cgi?id=89148 Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/radeon_cs.c | 16 ++++++++++++++-- drivers/gpu/drm/radeon/si.c | 15 ++++++++------- 2 files changed, 22 insertions(+), 9 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_cs.c b/drivers/gpu/drm/radeon/radeon_cs.c index c830863bc98a..a579ed379f20 100644 --- a/drivers/gpu/drm/radeon/radeon_cs.c +++ b/drivers/gpu/drm/radeon/radeon_cs.c @@ -715,6 +715,7 @@ int radeon_cs_packet_parse(struct radeon_cs_parser *p, struct radeon_cs_chunk *ib_chunk = p->chunk_ib; struct radeon_device *rdev = p->rdev; uint32_t header; + int ret = 0, i; if (idx >= ib_chunk->length_dw) { DRM_ERROR("Can not parse packet at %d after CS end %d !\n", @@ -743,14 +744,25 @@ int radeon_cs_packet_parse(struct radeon_cs_parser *p, break; default: DRM_ERROR("Unknown packet type %d at %d !\n", pkt->type, idx); - return -EINVAL; + ret = -EINVAL; + goto dump_ib; } if ((pkt->count + 1 + pkt->idx) >= ib_chunk->length_dw) { DRM_ERROR("Packet (%d:%d:%d) end after CS buffer (%d) !\n", pkt->idx, pkt->type, pkt->count, ib_chunk->length_dw); - return -EINVAL; + ret = -EINVAL; + goto dump_ib; } return 0; + +dump_ib: + for (i = 0; i < ib_chunk->length_dw; i++) { + if (i == idx) + printk("\t0x%08x <---\n", radeon_get_ib_value(p, i)); + else + printk("\t0x%08x\n", radeon_get_ib_value(p, i)); + } + return ret; } /** diff --git a/drivers/gpu/drm/radeon/si.c b/drivers/gpu/drm/radeon/si.c index 73107fe9e46f..ad26973733af 100644 --- a/drivers/gpu/drm/radeon/si.c +++ b/drivers/gpu/drm/radeon/si.c @@ -4699,12 +4699,6 @@ int si_ib_parse(struct radeon_device *rdev, struct radeon_ib *ib) switch (pkt.type) { case RADEON_PACKET_TYPE0: dev_err(rdev->dev, "Packet0 not allowed!\n"); - for (i = 0; i < ib->length_dw; i++) { - if (i == idx) - printk("\t0x%08x <---\n", ib->ptr[i]); - else - printk("\t0x%08x\n", ib->ptr[i]); - } ret = -EINVAL; break; case RADEON_PACKET_TYPE2: @@ -4736,8 +4730,15 @@ int si_ib_parse(struct radeon_device *rdev, struct radeon_ib *ib) ret = -EINVAL; break; } - if (ret) + if (ret) { + for (i = 0; i < ib->length_dw; i++) { + if (i == idx) + printk("\t0x%08x <---\n", ib->ptr[i]); + else + printk("\t0x%08x\n", ib->ptr[i]); + } break; + } } while (idx < ib->length_dw); return ret; -- cgit v1.2.3-59-g8ed1b From dc12a3ec712de225da48b35bd602e60397f25f2d Mon Sep 17 00:00:00 2001 From: Leo Liu Date: Wed, 18 Feb 2015 13:19:26 +0100 Subject: drm/radeon: enable SRBM timeout interrupt on CIK v2 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit v2: disable it on suspend Signed-off-by: Christian König Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/cik.c | 8 ++++++++ drivers/gpu/drm/radeon/cikd.h | 4 ++++ 2 files changed, 12 insertions(+) diff --git a/drivers/gpu/drm/radeon/cik.c b/drivers/gpu/drm/radeon/cik.c index e6a4ba236c70..0c993da9c8fb 100644 --- a/drivers/gpu/drm/radeon/cik.c +++ b/drivers/gpu/drm/radeon/cik.c @@ -3613,6 +3613,8 @@ static void cik_gpu_init(struct radeon_device *rdev) } WREG32(GRBM_CNTL, GRBM_READ_TIMEOUT(0xff)); + WREG32(SRBM_INT_CNTL, 0x1); + WREG32(SRBM_INT_ACK, 0x1); WREG32(BIF_FB_EN, FB_READ_EN | FB_WRITE_EN); @@ -7230,6 +7232,8 @@ static void cik_disable_interrupt_state(struct radeon_device *rdev) WREG32(CP_ME2_PIPE3_INT_CNTL, 0); /* grbm */ WREG32(GRBM_INT_CNTL, 0); + /* SRBM */ + WREG32(SRBM_INT_CNTL, 0); /* vline/vblank, etc. */ WREG32(LB_INTERRUPT_MASK + EVERGREEN_CRTC0_REGISTER_OFFSET, 0); WREG32(LB_INTERRUPT_MASK + EVERGREEN_CRTC1_REGISTER_OFFSET, 0); @@ -8046,6 +8050,10 @@ restart_ih: break; } break; + case 96: + DRM_ERROR("SRBM_READ_ERROR: 0x%x\n", RREG32(SRBM_READ_ERROR)); + WREG32(SRBM_INT_ACK, 0x1); + break; case 124: /* UVD */ DRM_DEBUG("IH: UVD int: 0x%08x\n", src_data); radeon_fence_process(rdev, R600_RING_TYPE_UVD_INDEX); diff --git a/drivers/gpu/drm/radeon/cikd.h b/drivers/gpu/drm/radeon/cikd.h index 03003f8a6de6..c648e1996dab 100644 --- a/drivers/gpu/drm/radeon/cikd.h +++ b/drivers/gpu/drm/radeon/cikd.h @@ -482,6 +482,10 @@ #define SOFT_RESET_ORB (1 << 23) #define SOFT_RESET_VCE (1 << 24) +#define SRBM_READ_ERROR 0xE98 +#define SRBM_INT_CNTL 0xEA0 +#define SRBM_INT_ACK 0xEA8 + #define VM_L2_CNTL 0x1400 #define ENABLE_L2_CACHE (1 << 0) #define ENABLE_L2_FRAGMENT_PROCESSING (1 << 1) -- cgit v1.2.3-59-g8ed1b From 18ad01effefe9c16454f2dfe045a9b5252d08d7a Mon Sep 17 00:00:00 2001 From: Christian König Date: Wed, 18 Feb 2015 13:19:27 +0100 Subject: drm/radeon: enable SRBM timeout interrupt on SI MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Christian König Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/si.c | 7 +++++++ drivers/gpu/drm/radeon/sid.h | 4 ++++ 2 files changed, 11 insertions(+) diff --git a/drivers/gpu/drm/radeon/si.c b/drivers/gpu/drm/radeon/si.c index ad26973733af..bcf516a8a2f1 100644 --- a/drivers/gpu/drm/radeon/si.c +++ b/drivers/gpu/drm/radeon/si.c @@ -3162,6 +3162,8 @@ static void si_gpu_init(struct radeon_device *rdev) } WREG32(GRBM_CNTL, GRBM_READ_TIMEOUT(0xff)); + WREG32(SRBM_INT_CNTL, 1); + WREG32(SRBM_INT_ACK, 1); evergreen_fix_pci_max_read_req_size(rdev); @@ -5911,6 +5913,7 @@ static void si_disable_interrupt_state(struct radeon_device *rdev) tmp = RREG32(DMA_CNTL + DMA1_REGISTER_OFFSET) & ~TRAP_ENABLE; WREG32(DMA_CNTL + DMA1_REGISTER_OFFSET, tmp); WREG32(GRBM_INT_CNTL, 0); + WREG32(SRBM_INT_CNTL, 0); if (rdev->num_crtc >= 2) { WREG32(INT_MASK + EVERGREEN_CRTC0_REGISTER_OFFSET, 0); WREG32(INT_MASK + EVERGREEN_CRTC1_REGISTER_OFFSET, 0); @@ -6610,6 +6613,10 @@ restart_ih: break; } break; + case 96: + DRM_ERROR("SRBM_READ_ERROR: 0x%x\n", RREG32(SRBM_READ_ERROR)); + WREG32(SRBM_INT_ACK, 0x1); + break; case 124: /* UVD */ DRM_DEBUG("IH: UVD int: 0x%08x\n", src_data); radeon_fence_process(rdev, R600_RING_TYPE_UVD_INDEX); diff --git a/drivers/gpu/drm/radeon/sid.h b/drivers/gpu/drm/radeon/sid.h index cbd91d226f3c..c27118cab16a 100644 --- a/drivers/gpu/drm/radeon/sid.h +++ b/drivers/gpu/drm/radeon/sid.h @@ -358,6 +358,10 @@ #define CC_SYS_RB_BACKEND_DISABLE 0xe80 #define GC_USER_SYS_RB_BACKEND_DISABLE 0xe84 +#define SRBM_READ_ERROR 0xE98 +#define SRBM_INT_CNTL 0xEA0 +#define SRBM_INT_ACK 0xEA8 + #define SRBM_STATUS2 0x0EC4 #define DMA_BUSY (1 << 5) #define DMA1_BUSY (1 << 6) -- cgit v1.2.3-59-g8ed1b From acc1522a54a3ff4dc250b6e94c55c53c5240e234 Mon Sep 17 00:00:00 2001 From: Christian König Date: Wed, 18 Feb 2015 13:19:28 +0100 Subject: drm/radeon: enable SRBM timeout interrupt on EG/NI MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Christian König Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/evergreen.c | 7 +++++++ drivers/gpu/drm/radeon/evergreend.h | 4 ++++ drivers/gpu/drm/radeon/ni.c | 2 ++ drivers/gpu/drm/radeon/nid.h | 4 ++++ 4 files changed, 17 insertions(+) diff --git a/drivers/gpu/drm/radeon/evergreen.c b/drivers/gpu/drm/radeon/evergreen.c index 78600f534c80..4c0e24b3bb90 100644 --- a/drivers/gpu/drm/radeon/evergreen.c +++ b/drivers/gpu/drm/radeon/evergreen.c @@ -3253,6 +3253,8 @@ static void evergreen_gpu_init(struct radeon_device *rdev) } WREG32(GRBM_CNTL, GRBM_READ_TIMEOUT(0xff)); + WREG32(SRBM_INT_CNTL, 0x1); + WREG32(SRBM_INT_ACK, 0x1); evergreen_fix_pci_max_read_req_size(rdev); @@ -4324,6 +4326,7 @@ void evergreen_disable_interrupt_state(struct radeon_device *rdev) tmp = RREG32(DMA_CNTL) & ~TRAP_ENABLE; WREG32(DMA_CNTL, tmp); WREG32(GRBM_INT_CNTL, 0); + WREG32(SRBM_INT_CNTL, 0); WREG32(INT_MASK + EVERGREEN_CRTC0_REGISTER_OFFSET, 0); WREG32(INT_MASK + EVERGREEN_CRTC1_REGISTER_OFFSET, 0); if (rdev->num_crtc >= 4) { @@ -5066,6 +5069,10 @@ restart_ih: DRM_ERROR("Unhandled interrupt: %d %d\n", src_id, src_data); break; } + case 96: + DRM_ERROR("SRBM_READ_ERROR: 0x%x\n", RREG32(SRBM_READ_ERROR)); + WREG32(SRBM_INT_ACK, 0x1); + break; case 124: /* UVD */ DRM_DEBUG("IH: UVD int: 0x%08x\n", src_data); radeon_fence_process(rdev, R600_RING_TYPE_UVD_INDEX); diff --git a/drivers/gpu/drm/radeon/evergreend.h b/drivers/gpu/drm/radeon/evergreend.h index ee83d2a88750..a8d1d5240fcb 100644 --- a/drivers/gpu/drm/radeon/evergreend.h +++ b/drivers/gpu/drm/radeon/evergreend.h @@ -1191,6 +1191,10 @@ #define SOFT_RESET_REGBB (1 << 22) #define SOFT_RESET_ORB (1 << 23) +#define SRBM_READ_ERROR 0xE98 +#define SRBM_INT_CNTL 0xEA0 +#define SRBM_INT_ACK 0xEA8 + /* display watermarks */ #define DC_LB_MEMORY_SPLIT 0x6b0c #define PRIORITY_A_CNT 0x6b18 diff --git a/drivers/gpu/drm/radeon/ni.c b/drivers/gpu/drm/radeon/ni.c index 24242a7f0ac3..ebe68dd8e06a 100644 --- a/drivers/gpu/drm/radeon/ni.c +++ b/drivers/gpu/drm/radeon/ni.c @@ -962,6 +962,8 @@ static void cayman_gpu_init(struct radeon_device *rdev) } WREG32(GRBM_CNTL, GRBM_READ_TIMEOUT(0xff)); + WREG32(SRBM_INT_CNTL, 0x1); + WREG32(SRBM_INT_ACK, 0x1); evergreen_fix_pci_max_read_req_size(rdev); diff --git a/drivers/gpu/drm/radeon/nid.h b/drivers/gpu/drm/radeon/nid.h index ad7125486894..6b44580440d0 100644 --- a/drivers/gpu/drm/radeon/nid.h +++ b/drivers/gpu/drm/radeon/nid.h @@ -82,6 +82,10 @@ #define SOFT_RESET_REGBB (1 << 22) #define SOFT_RESET_ORB (1 << 23) +#define SRBM_READ_ERROR 0xE98 +#define SRBM_INT_CNTL 0xEA0 +#define SRBM_INT_ACK 0xEA8 + #define SRBM_STATUS2 0x0EC4 #define DMA_BUSY (1 << 5) #define DMA1_BUSY (1 << 6) -- cgit v1.2.3-59-g8ed1b From dbfb00c3e7e18439f2ebf67fe99bf7a50b5bae1e Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Thu, 19 Feb 2015 16:02:15 -0500 Subject: drm/radeon: fix 1 RB harvest config setup for TN/RL The logic was reversed from what the hw actually exposed. Fixes graphics corruption in certain harvest configurations. Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/ni.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/radeon/ni.c b/drivers/gpu/drm/radeon/ni.c index ebe68dd8e06a..dab00812abaa 100644 --- a/drivers/gpu/drm/radeon/ni.c +++ b/drivers/gpu/drm/radeon/ni.c @@ -1088,12 +1088,12 @@ static void cayman_gpu_init(struct radeon_device *rdev) if ((rdev->config.cayman.max_backends_per_se == 1) && (rdev->flags & RADEON_IS_IGP)) { - if ((disabled_rb_mask & 3) == 1) { - /* RB0 disabled, RB1 enabled */ - tmp = 0x11111111; - } else { + if ((disabled_rb_mask & 3) == 2) { /* RB1 disabled, RB0 enabled */ tmp = 0x00000000; + } else { + /* RB0 disabled, RB1 enabled */ + tmp = 0x11111111; } } else { tmp = gb_addr_config & NUM_PIPES_MASK; -- cgit v1.2.3-59-g8ed1b From 94a47c49fe5dc0c4d1e56bc1286623df3ea53b23 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 20 Feb 2015 11:51:38 -0500 Subject: drm/radeon: fix atom aux payload size check for writes (v2) MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The atom aux param interface only supports 4 bits for the total write transfer size (header + payload). This limits us to 12 bytes of payload rather than 16. Add a check for this. Reads are not affected. v2: switch to WARN_ON_ONCE Reviewed-by: Michel Dänzer Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/atombios_dp.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/gpu/drm/radeon/atombios_dp.c b/drivers/gpu/drm/radeon/atombios_dp.c index 5bf825dfaa09..8d74de82456e 100644 --- a/drivers/gpu/drm/radeon/atombios_dp.c +++ b/drivers/gpu/drm/radeon/atombios_dp.c @@ -178,6 +178,13 @@ radeon_dp_aux_transfer(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg) switch (msg->request & ~DP_AUX_I2C_MOT) { case DP_AUX_NATIVE_WRITE: case DP_AUX_I2C_WRITE: + /* The atom implementation only supports writes with a max payload of + * 12 bytes since it uses 4 bits for the total count (header + payload) + * in the parameter space. The atom interface supports 16 byte + * payloads for reads. The hw itself supports up to 16 bytes of payload. + */ + if (WARN_ON_ONCE(msg->size > 12)) + return -E2BIG; /* tx_size needs to be 4 even for bare address packets since the atom * table needs the info in tx_buf[3]. */ -- cgit v1.2.3-59-g8ed1b From 3473f542ab707afbb6e6057ddb6f3b40ef22e093 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 23 Feb 2015 17:45:54 -0500 Subject: drm/radeon: only enable DP audio if the monitor supports it We were enabling DP secondary streams even if the monitor didn't support them. Fixes display problems on some DP monitors. Tested-by: Jim Boz Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/atombios_encoders.c | 21 +++++++++++++++------ 1 file changed, 15 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/radeon/atombios_encoders.c b/drivers/gpu/drm/radeon/atombios_encoders.c index 7c9df1eac065..7fe7b749e182 100644 --- a/drivers/gpu/drm/radeon/atombios_encoders.c +++ b/drivers/gpu/drm/radeon/atombios_encoders.c @@ -731,7 +731,9 @@ atombios_get_encoder_mode(struct drm_encoder *encoder) dig_connector = radeon_connector->con_priv; if ((dig_connector->dp_sink_type == CONNECTOR_OBJECT_ID_DISPLAYPORT) || (dig_connector->dp_sink_type == CONNECTOR_OBJECT_ID_eDP)) { - if (radeon_audio != 0 && ASIC_IS_DCE4(rdev) && !ASIC_IS_DCE5(rdev)) + if (radeon_audio != 0 && + drm_detect_monitor_audio(radeon_connector_edid(connector)) && + ASIC_IS_DCE4(rdev) && !ASIC_IS_DCE5(rdev)) return ATOM_ENCODER_MODE_DP_AUDIO; return ATOM_ENCODER_MODE_DP; } else if (radeon_audio != 0) { @@ -747,7 +749,9 @@ atombios_get_encoder_mode(struct drm_encoder *encoder) } break; case DRM_MODE_CONNECTOR_eDP: - if (radeon_audio != 0 && ASIC_IS_DCE4(rdev) && !ASIC_IS_DCE5(rdev)) + if (radeon_audio != 0 && + drm_detect_monitor_audio(radeon_connector_edid(connector)) && + ASIC_IS_DCE4(rdev) && !ASIC_IS_DCE5(rdev)) return ATOM_ENCODER_MODE_DP_AUDIO; return ATOM_ENCODER_MODE_DP; case DRM_MODE_CONNECTOR_DVIA: @@ -1720,8 +1724,10 @@ radeon_atom_encoder_dpms_dig(struct drm_encoder *encoder, int mode) } encoder_mode = atombios_get_encoder_mode(encoder); - if (radeon_audio != 0 && - (encoder_mode == ATOM_ENCODER_MODE_HDMI || ENCODER_MODE_IS_DP(encoder_mode))) + if (connector && (radeon_audio != 0) && + ((encoder_mode == ATOM_ENCODER_MODE_HDMI) || + (ENCODER_MODE_IS_DP(encoder_mode) && + drm_detect_monitor_audio(radeon_connector_edid(connector))))) radeon_audio_dpms(encoder, mode); } @@ -2136,6 +2142,7 @@ radeon_atom_encoder_mode_set(struct drm_encoder *encoder, struct drm_device *dev = encoder->dev; struct radeon_device *rdev = dev->dev_private; struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); + struct drm_connector *connector = radeon_get_connector_for_encoder(encoder); int encoder_mode; radeon_encoder->pixel_clock = adjusted_mode->clock; @@ -2164,8 +2171,10 @@ radeon_atom_encoder_mode_set(struct drm_encoder *encoder, case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA: /* handled in dpms */ encoder_mode = atombios_get_encoder_mode(encoder); - if (radeon_audio != 0 && - (encoder_mode == ATOM_ENCODER_MODE_HDMI || ENCODER_MODE_IS_DP(encoder_mode))) + if (connector && (radeon_audio != 0) && + ((encoder_mode == ATOM_ENCODER_MODE_HDMI) || + (ENCODER_MODE_IS_DP(encoder_mode) && + drm_detect_monitor_audio(radeon_connector_edid(connector))))) radeon_audio_mode_set(encoder, adjusted_mode); break; case ENCODER_OBJECT_ID_INTERNAL_DDI: -- cgit v1.2.3-59-g8ed1b From 74ad752442d9488cf02ee2a9243d6c6b5c943efb Mon Sep 17 00:00:00 2001 From: Tom Lendacky Date: Tue, 24 Feb 2015 10:47:49 -0600 Subject: amd-xgbe-phy: PHY KX/KR mode differences The PHY requires different settings for the Decision Feedback Analyzer (DFE) when running in KX mode vs. KR mode. Update the code to change these settings when changing modes in order to provide a more stable link. Additionally, adjust the 10GbE PQ skew default setting to a more sane value. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- .../devicetree/bindings/net/amd-xgbe-phy.txt | 4 ++ drivers/net/phy/amd-xgbe-phy.c | 82 +++++++++++++++++++++- 2 files changed, 84 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt index 33df3932168e..8db32384a486 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -27,6 +27,8 @@ property is used. - amd,serdes-cdr-rate: CDR rate speed selection - amd,serdes-pq-skew: PQ (data sampling) skew - amd,serdes-tx-amp: TX amplitude boost +- amd,serdes-dfe-tap-config: DFE taps available to run +- amd,serdes-dfe-tap-enable: DFE taps to enable Example: xgbe_phy@e1240800 { @@ -41,4 +43,6 @@ Example: amd,serdes-cdr-rate = <2>, <2>, <7>; amd,serdes-pq-skew = <10>, <10>, <30>; amd,serdes-tx-amp = <15>, <15>, <10>; + amd,serdes-dfe-tap-config = <3>, <3>, <1>; + amd,serdes-dfe-tap-enable = <0>, <0>, <127>; }; diff --git a/drivers/net/phy/amd-xgbe-phy.c b/drivers/net/phy/amd-xgbe-phy.c index 9e3af54c9010..32efbd48f326 100644 --- a/drivers/net/phy/amd-xgbe-phy.c +++ b/drivers/net/phy/amd-xgbe-phy.c @@ -92,6 +92,8 @@ MODULE_DESCRIPTION("AMD 10GbE (amd-xgbe) PHY driver"); #define XGBE_PHY_CDR_RATE_PROPERTY "amd,serdes-cdr-rate" #define XGBE_PHY_PQ_SKEW_PROPERTY "amd,serdes-pq-skew" #define XGBE_PHY_TX_AMP_PROPERTY "amd,serdes-tx-amp" +#define XGBE_PHY_DFE_CFG_PROPERTY "amd,serdes-dfe-tap-config" +#define XGBE_PHY_DFE_ENA_PROPERTY "amd,serdes-dfe-tap-enable" #define XGBE_PHY_SPEEDS 3 #define XGBE_PHY_SPEED_1000 0 @@ -177,10 +179,12 @@ MODULE_DESCRIPTION("AMD 10GbE (amd-xgbe) PHY driver"); #define SPEED_10000_BLWC 0 #define SPEED_10000_CDR 0x7 #define SPEED_10000_PLL 0x1 -#define SPEED_10000_PQ 0x1e +#define SPEED_10000_PQ 0x12 #define SPEED_10000_RATE 0x0 #define SPEED_10000_TXAMP 0xa #define SPEED_10000_WORD 0x7 +#define SPEED_10000_DFE_TAP_CONFIG 0x1 +#define SPEED_10000_DFE_TAP_ENABLE 0x7f #define SPEED_2500_BLWC 1 #define SPEED_2500_CDR 0x2 @@ -189,6 +193,8 @@ MODULE_DESCRIPTION("AMD 10GbE (amd-xgbe) PHY driver"); #define SPEED_2500_RATE 0x1 #define SPEED_2500_TXAMP 0xf #define SPEED_2500_WORD 0x1 +#define SPEED_2500_DFE_TAP_CONFIG 0x3 +#define SPEED_2500_DFE_TAP_ENABLE 0x0 #define SPEED_1000_BLWC 1 #define SPEED_1000_CDR 0x2 @@ -197,16 +203,25 @@ MODULE_DESCRIPTION("AMD 10GbE (amd-xgbe) PHY driver"); #define SPEED_1000_RATE 0x3 #define SPEED_1000_TXAMP 0xf #define SPEED_1000_WORD 0x1 +#define SPEED_1000_DFE_TAP_CONFIG 0x3 +#define SPEED_1000_DFE_TAP_ENABLE 0x0 /* SerDes RxTx register offsets */ +#define RXTX_REG6 0x0018 #define RXTX_REG20 0x0050 +#define RXTX_REG22 0x0058 #define RXTX_REG114 0x01c8 +#define RXTX_REG129 0x0204 /* SerDes RxTx register entry bit positions and sizes */ +#define RXTX_REG6_RESETB_RXD_INDEX 8 +#define RXTX_REG6_RESETB_RXD_WIDTH 1 #define RXTX_REG20_BLWC_ENA_INDEX 2 #define RXTX_REG20_BLWC_ENA_WIDTH 1 #define RXTX_REG114_PQ_REG_INDEX 9 #define RXTX_REG114_PQ_REG_WIDTH 7 +#define RXTX_REG129_RXDFE_CONFIG_INDEX 14 +#define RXTX_REG129_RXDFE_CONFIG_WIDTH 2 /* Bit setting and getting macros * The get macro will extract the current bit field value from within @@ -333,6 +348,18 @@ static const u32 amd_xgbe_phy_serdes_tx_amp[] = { SPEED_10000_TXAMP, }; +static const u32 amd_xgbe_phy_serdes_dfe_tap_cfg[] = { + SPEED_1000_DFE_TAP_CONFIG, + SPEED_2500_DFE_TAP_CONFIG, + SPEED_10000_DFE_TAP_CONFIG, +}; + +static const u32 amd_xgbe_phy_serdes_dfe_tap_ena[] = { + SPEED_1000_DFE_TAP_ENABLE, + SPEED_2500_DFE_TAP_ENABLE, + SPEED_10000_DFE_TAP_ENABLE, +}; + enum amd_xgbe_phy_an { AMD_XGBE_AN_READY = 0, AMD_XGBE_AN_PAGE_RECEIVED, @@ -393,6 +420,8 @@ struct amd_xgbe_phy_priv { u32 serdes_cdr_rate[XGBE_PHY_SPEEDS]; u32 serdes_pq_skew[XGBE_PHY_SPEEDS]; u32 serdes_tx_amp[XGBE_PHY_SPEEDS]; + u32 serdes_dfe_tap_cfg[XGBE_PHY_SPEEDS]; + u32 serdes_dfe_tap_ena[XGBE_PHY_SPEEDS]; /* Auto-negotiation state machine support */ struct mutex an_mutex; @@ -481,11 +510,16 @@ static void amd_xgbe_phy_serdes_complete_ratechange(struct phy_device *phydev) status = XSIR0_IOREAD(priv, SIR0_STATUS); if (XSIR_GET_BITS(status, SIR0_STATUS, RX_READY) && XSIR_GET_BITS(status, SIR0_STATUS, TX_READY)) - return; + goto rx_reset; } netdev_dbg(phydev->attached_dev, "SerDes rx/tx not ready (%#hx)\n", status); + +rx_reset: + /* Perform Rx reset for the DFE changes */ + XRXTX_IOWRITE_BITS(priv, RXTX_REG6, RESETB_RXD, 0); + XRXTX_IOWRITE_BITS(priv, RXTX_REG6, RESETB_RXD, 1); } static int amd_xgbe_phy_xgmii_mode(struct phy_device *phydev) @@ -534,6 +568,10 @@ static int amd_xgbe_phy_xgmii_mode(struct phy_device *phydev) priv->serdes_blwc[XGBE_PHY_SPEED_10000]); XRXTX_IOWRITE_BITS(priv, RXTX_REG114, PQ_REG, priv->serdes_pq_skew[XGBE_PHY_SPEED_10000]); + XRXTX_IOWRITE_BITS(priv, RXTX_REG129, RXDFE_CONFIG, + priv->serdes_dfe_tap_cfg[XGBE_PHY_SPEED_10000]); + XRXTX_IOWRITE(priv, RXTX_REG22, + priv->serdes_dfe_tap_ena[XGBE_PHY_SPEED_10000]); amd_xgbe_phy_serdes_complete_ratechange(phydev); @@ -586,6 +624,10 @@ static int amd_xgbe_phy_gmii_2500_mode(struct phy_device *phydev) priv->serdes_blwc[XGBE_PHY_SPEED_2500]); XRXTX_IOWRITE_BITS(priv, RXTX_REG114, PQ_REG, priv->serdes_pq_skew[XGBE_PHY_SPEED_2500]); + XRXTX_IOWRITE_BITS(priv, RXTX_REG129, RXDFE_CONFIG, + priv->serdes_dfe_tap_cfg[XGBE_PHY_SPEED_2500]); + XRXTX_IOWRITE(priv, RXTX_REG22, + priv->serdes_dfe_tap_ena[XGBE_PHY_SPEED_2500]); amd_xgbe_phy_serdes_complete_ratechange(phydev); @@ -638,6 +680,10 @@ static int amd_xgbe_phy_gmii_mode(struct phy_device *phydev) priv->serdes_blwc[XGBE_PHY_SPEED_1000]); XRXTX_IOWRITE_BITS(priv, RXTX_REG114, PQ_REG, priv->serdes_pq_skew[XGBE_PHY_SPEED_1000]); + XRXTX_IOWRITE_BITS(priv, RXTX_REG129, RXDFE_CONFIG, + priv->serdes_dfe_tap_cfg[XGBE_PHY_SPEED_1000]); + XRXTX_IOWRITE(priv, RXTX_REG22, + priv->serdes_dfe_tap_ena[XGBE_PHY_SPEED_1000]); amd_xgbe_phy_serdes_complete_ratechange(phydev); @@ -1668,6 +1714,38 @@ static int amd_xgbe_phy_probe(struct phy_device *phydev) sizeof(priv->serdes_tx_amp)); } + if (device_property_present(phy_dev, XGBE_PHY_DFE_CFG_PROPERTY)) { + ret = device_property_read_u32_array(phy_dev, + XGBE_PHY_DFE_CFG_PROPERTY, + priv->serdes_dfe_tap_cfg, + XGBE_PHY_SPEEDS); + if (ret) { + dev_err(dev, "invalid %s property\n", + XGBE_PHY_DFE_CFG_PROPERTY); + goto err_sir1; + } + } else { + memcpy(priv->serdes_dfe_tap_cfg, + amd_xgbe_phy_serdes_dfe_tap_cfg, + sizeof(priv->serdes_dfe_tap_cfg)); + } + + if (device_property_present(phy_dev, XGBE_PHY_DFE_ENA_PROPERTY)) { + ret = device_property_read_u32_array(phy_dev, + XGBE_PHY_DFE_ENA_PROPERTY, + priv->serdes_dfe_tap_ena, + XGBE_PHY_SPEEDS); + if (ret) { + dev_err(dev, "invalid %s property\n", + XGBE_PHY_DFE_ENA_PROPERTY); + goto err_sir1; + } + } else { + memcpy(priv->serdes_dfe_tap_ena, + amd_xgbe_phy_serdes_dfe_tap_ena, + sizeof(priv->serdes_dfe_tap_ena)); + } + phydev->priv = priv; if (!priv->adev || acpi_disabled) -- cgit v1.2.3-59-g8ed1b From 31639b94cadc03727d0ae1f048e9688dd508883f Mon Sep 17 00:00:00 2001 From: Andy Gospodarek Date: Wed, 25 Feb 2015 17:00:16 -0500 Subject: MAINTAINERS: update my email address I have been signing off on patches with this address so I'll change it. Signed-off-by: Andy Gospodarek Signed-off-by: David S. Miller --- MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index 4f4915cbeab9..5d1606e9f558 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2065,7 +2065,7 @@ F: include/net/bluetooth/ BONDING DRIVER M: Jay Vosburgh M: Veaceslav Falico -M: Andy Gospodarek +M: Andy Gospodarek L: netdev@vger.kernel.org W: http://sourceforge.net/projects/bonding/ S: Supported -- cgit v1.2.3-59-g8ed1b From 737eb0301f296d55c22350c6968ff1ef51bacb5f Mon Sep 17 00:00:00 2001 From: Mark Rutland Date: Fri, 20 Feb 2015 14:53:46 +0000 Subject: genirq / PM: better describe IRQF_NO_SUSPEND semantics The IRQF_NO_SUSPEND flag is intended to be used for interrupts required to be enabled during the suspend-resume cycle. This mostly consists of IPIs and timer interrupts, potentially including chained irqchip interrupts if these are necessary to handle timers or IPIs. If an interrupt does not fall into one of the aforementioned categories, requesting it with IRQF_NO_SUSPEND is likely incorrect. Using IRQF_NO_SUSPEND does not guarantee that the interrupt can wake the system from a suspended state. For an interrupt to be able to trigger a wakeup, it may be necessary to program various components of the system. In these cases it is necessary to use {enable,disabled}_irq_wake. Unfortunately, several drivers assume that IRQF_NO_SUSPEND ensures that an IRQ can wake up the system, and the documentation can be read ambiguously w.r.t. this property. This patch updates the documentation regarding IRQF_NO_SUSPEND to make this caveat explicit, hopefully making future misuse rarer. Cleanup of existing misuse will occur as part of later patch series. Signed-off-by: Mark Rutland Acked-by: Peter Zijlstra (Intel) Signed-off-by: Rafael J. Wysocki --- Documentation/power/suspend-and-interrupts.txt | 6 ++++-- include/linux/interrupt.h | 4 +++- 2 files changed, 7 insertions(+), 3 deletions(-) diff --git a/Documentation/power/suspend-and-interrupts.txt b/Documentation/power/suspend-and-interrupts.txt index 2f9c5a5fcb25..50493c9284b4 100644 --- a/Documentation/power/suspend-and-interrupts.txt +++ b/Documentation/power/suspend-and-interrupts.txt @@ -40,8 +40,10 @@ but also to IPIs and to some other special-purpose interrupts. The IRQF_NO_SUSPEND flag is used to indicate that to the IRQ subsystem when requesting a special-purpose interrupt. It causes suspend_device_irqs() to -leave the corresponding IRQ enabled so as to allow the interrupt to work all -the time as expected. +leave the corresponding IRQ enabled so as to allow the interrupt to work as +expected during the suspend-resume cycle, but does not guarantee that the +interrupt will wake the system from a suspended state -- for such cases it is +necessary to use enable_irq_wake(). Note that the IRQF_NO_SUSPEND flag affects the entire IRQ and not just one user of it. Thus, if the IRQ is shared, all of the interrupt handlers installed diff --git a/include/linux/interrupt.h b/include/linux/interrupt.h index d9b05b5bf8c7..606771c7cac2 100644 --- a/include/linux/interrupt.h +++ b/include/linux/interrupt.h @@ -52,7 +52,9 @@ * IRQF_ONESHOT - Interrupt is not reenabled after the hardirq handler finished. * Used by threaded interrupts which need to keep the * irq line disabled until the threaded handler has been run. - * IRQF_NO_SUSPEND - Do not disable this IRQ during suspend + * IRQF_NO_SUSPEND - Do not disable this IRQ during suspend. Does not guarantee + * that this interrupt will wake the system from a suspended + * state. See Documentation/power/suspend-and-interrupts.txt * IRQF_FORCE_RESUME - Force enable it on resume even if IRQF_NO_SUSPEND is set * IRQF_NO_THREAD - Interrupt cannot be threaded * IRQF_EARLY_RESUME - Resume IRQ early during syscore instead of at device -- cgit v1.2.3-59-g8ed1b From 70068776c49b37fe0c8f9115cec068d07375c6fb Mon Sep 17 00:00:00 2001 From: Oder Chiou Date: Wed, 25 Feb 2015 17:36:13 +0800 Subject: ASoC: rt5677: Correct the routing paths of that after IF1/2 DACx Mux The patch corrects the routing paths of that after IF1/2 DACx Mux Signed-off-by: Oder Chiou Signed-off-by: Mark Brown --- sound/soc/codecs/rt5677.c | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c index 5d0bb8748dd1..fb9c20eace3f 100644 --- a/sound/soc/codecs/rt5677.c +++ b/sound/soc/codecs/rt5677.c @@ -3284,8 +3284,8 @@ static const struct snd_soc_dapm_route rt5677_dapm_routes[] = { { "IB45 Bypass Mux", "Bypass", "IB45 Mux" }, { "IB45 Bypass Mux", "Pass SRC", "IB45 Mux" }, - { "IB6 Mux", "IF1 DAC 6", "IF1 DAC6" }, - { "IB6 Mux", "IF2 DAC 6", "IF2 DAC6" }, + { "IB6 Mux", "IF1 DAC 6", "IF1 DAC6 Mux" }, + { "IB6 Mux", "IF2 DAC 6", "IF2 DAC6 Mux" }, { "IB6 Mux", "SLB DAC 6", "SLB DAC6" }, { "IB6 Mux", "STO4 ADC MIX L", "Stereo4 ADC MIXL" }, { "IB6 Mux", "IF4 DAC L", "IF4 DAC L" }, @@ -3293,8 +3293,8 @@ static const struct snd_soc_dapm_route rt5677_dapm_routes[] = { { "IB6 Mux", "STO2 ADC MIX L", "Stereo2 ADC MIXL" }, { "IB6 Mux", "STO3 ADC MIX L", "Stereo3 ADC MIXL" }, - { "IB7 Mux", "IF1 DAC 7", "IF1 DAC7" }, - { "IB7 Mux", "IF2 DAC 7", "IF2 DAC7" }, + { "IB7 Mux", "IF1 DAC 7", "IF1 DAC7 Mux" }, + { "IB7 Mux", "IF2 DAC 7", "IF2 DAC7 Mux" }, { "IB7 Mux", "SLB DAC 7", "SLB DAC7" }, { "IB7 Mux", "STO4 ADC MIX R", "Stereo4 ADC MIXR" }, { "IB7 Mux", "IF4 DAC R", "IF4 DAC R" }, @@ -3635,15 +3635,15 @@ static const struct snd_soc_dapm_route rt5677_dapm_routes[] = { { "DAC1 FS", NULL, "DAC1 MIXL" }, { "DAC1 FS", NULL, "DAC1 MIXR" }, - { "DAC2 L Mux", "IF1 DAC 2", "IF1 DAC2" }, - { "DAC2 L Mux", "IF2 DAC 2", "IF2 DAC2" }, + { "DAC2 L Mux", "IF1 DAC 2", "IF1 DAC2 Mux" }, + { "DAC2 L Mux", "IF2 DAC 2", "IF2 DAC2 Mux" }, { "DAC2 L Mux", "IF3 DAC L", "IF3 DAC L" }, { "DAC2 L Mux", "IF4 DAC L", "IF4 DAC L" }, { "DAC2 L Mux", "SLB DAC 2", "SLB DAC2" }, { "DAC2 L Mux", "OB 2", "OutBound2" }, - { "DAC2 R Mux", "IF1 DAC 3", "IF1 DAC3" }, - { "DAC2 R Mux", "IF2 DAC 3", "IF2 DAC3" }, + { "DAC2 R Mux", "IF1 DAC 3", "IF1 DAC3 Mux" }, + { "DAC2 R Mux", "IF2 DAC 3", "IF2 DAC3 Mux" }, { "DAC2 R Mux", "IF3 DAC R", "IF3 DAC R" }, { "DAC2 R Mux", "IF4 DAC R", "IF4 DAC R" }, { "DAC2 R Mux", "SLB DAC 3", "SLB DAC3" }, @@ -3651,29 +3651,29 @@ static const struct snd_soc_dapm_route rt5677_dapm_routes[] = { { "DAC2 R Mux", "Haptic Generator", "Haptic Generator" }, { "DAC2 R Mux", "VAD ADC", "VAD ADC Mux" }, - { "DAC3 L Mux", "IF1 DAC 4", "IF1 DAC4" }, - { "DAC3 L Mux", "IF2 DAC 4", "IF2 DAC4" }, + { "DAC3 L Mux", "IF1 DAC 4", "IF1 DAC4 Mux" }, + { "DAC3 L Mux", "IF2 DAC 4", "IF2 DAC4 Mux" }, { "DAC3 L Mux", "IF3 DAC L", "IF3 DAC L" }, { "DAC3 L Mux", "IF4 DAC L", "IF4 DAC L" }, { "DAC3 L Mux", "SLB DAC 4", "SLB DAC4" }, { "DAC3 L Mux", "OB 4", "OutBound4" }, - { "DAC3 R Mux", "IF1 DAC 5", "IF1 DAC4" }, - { "DAC3 R Mux", "IF2 DAC 5", "IF2 DAC4" }, + { "DAC3 R Mux", "IF1 DAC 5", "IF1 DAC5 Mux" }, + { "DAC3 R Mux", "IF2 DAC 5", "IF2 DAC5 Mux" }, { "DAC3 R Mux", "IF3 DAC R", "IF3 DAC R" }, { "DAC3 R Mux", "IF4 DAC R", "IF4 DAC R" }, { "DAC3 R Mux", "SLB DAC 5", "SLB DAC5" }, { "DAC3 R Mux", "OB 5", "OutBound5" }, - { "DAC4 L Mux", "IF1 DAC 6", "IF1 DAC6" }, - { "DAC4 L Mux", "IF2 DAC 6", "IF2 DAC6" }, + { "DAC4 L Mux", "IF1 DAC 6", "IF1 DAC6 Mux" }, + { "DAC4 L Mux", "IF2 DAC 6", "IF2 DAC6 Mux" }, { "DAC4 L Mux", "IF3 DAC L", "IF3 DAC L" }, { "DAC4 L Mux", "IF4 DAC L", "IF4 DAC L" }, { "DAC4 L Mux", "SLB DAC 6", "SLB DAC6" }, { "DAC4 L Mux", "OB 6", "OutBound6" }, - { "DAC4 R Mux", "IF1 DAC 7", "IF1 DAC7" }, - { "DAC4 R Mux", "IF2 DAC 7", "IF2 DAC7" }, + { "DAC4 R Mux", "IF1 DAC 7", "IF1 DAC7 Mux" }, + { "DAC4 R Mux", "IF2 DAC 7", "IF2 DAC7 Mux" }, { "DAC4 R Mux", "IF3 DAC R", "IF3 DAC R" }, { "DAC4 R Mux", "IF4 DAC R", "IF4 DAC R" }, { "DAC4 R Mux", "SLB DAC 7", "SLB DAC7" }, -- cgit v1.2.3-59-g8ed1b From 8af4baa7087a0ae74c6ee29d4d979a60e14b119e Mon Sep 17 00:00:00 2001 From: Thomas Niederprüm Date: Sat, 21 Feb 2015 18:11:29 +0100 Subject: ASoC: OMAP: mcbsp: Fix CLKX and CLKR pinmux when used as inputs MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This patch fixes faulty behaviour in a setup where the input clock for the SRG is fed through the CLKR/CLKX pin but the McBSP is configured to be master (SND_SOC_DAIFMT_CBS_CFS). In that case of course CLKR/CLKX must not be configured as output pin. Otherwise the input clock is messed up horribly. This patch makes it possible to use the CLKR/CLKX pin rather than CLKS to inject a reference clock in setups where McBSP is master and not both rx and tx are used. However for this to work it has to be ensured that set_dai_sysclk() is called after set_dai_fmt(). This was tested on a beagleboard-xm using McBSP1 to drive a i2s DAC through the tx lines (CLKX,FSX,DX). Using this patch the CLKR pin is used to inject an external reference clock. Signed-off-by: Thomas Niederprüm Acked-by: Peter Ujfalusi Signed-off-by: Mark Brown --- sound/soc/omap/omap-mcbsp.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/sound/soc/omap/omap-mcbsp.c b/sound/soc/omap/omap-mcbsp.c index c7eb9dd67f60..fd99d89de6a8 100644 --- a/sound/soc/omap/omap-mcbsp.c +++ b/sound/soc/omap/omap-mcbsp.c @@ -530,8 +530,19 @@ static int omap_mcbsp_dai_set_dai_sysclk(struct snd_soc_dai *cpu_dai, case OMAP_MCBSP_SYSCLK_CLKX_EXT: regs->srgr2 |= CLKSM; + regs->pcr0 |= SCLKME; + /* + * If McBSP is master but yet the CLKX/CLKR pin drives the SRG, + * disable output on those pins. This enables to inject the + * reference clock through CLKX/CLKR. For this to work + * set_dai_sysclk() _needs_ to be called after set_dai_fmt(). + */ + regs->pcr0 &= ~CLKXM; + break; case OMAP_MCBSP_SYSCLK_CLKR_EXT: regs->pcr0 |= SCLKME; + /* Disable ouput on CLKR pin in master mode */ + regs->pcr0 &= ~CLKRM; break; default: err = -ENODEV; -- cgit v1.2.3-59-g8ed1b From dda094a312dbb2cd96e3e46fce7784aca999bcf1 Mon Sep 17 00:00:00 2001 From: Alexey Khoroshilov Date: Sat, 21 Feb 2015 07:32:47 +0000 Subject: i40e: Fix memory leak at failure path in i40e_dbg_command_write() The patch fixes a leak of 'cmd_buf' when copy_from_user() failed in i40e_dbg_command_write(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_debugfs.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_debugfs.c b/drivers/net/ethernet/intel/i40e/i40e_debugfs.c index 61236f983971..c17ee77100d3 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_debugfs.c +++ b/drivers/net/ethernet/intel/i40e/i40e_debugfs.c @@ -989,8 +989,10 @@ static ssize_t i40e_dbg_command_write(struct file *filp, if (!cmd_buf) return count; bytes_not_copied = copy_from_user(cmd_buf, buffer, count); - if (bytes_not_copied < 0) + if (bytes_not_copied < 0) { + kfree(cmd_buf); return bytes_not_copied; + } if (bytes_not_copied > 0) count -= bytes_not_copied; cmd_buf[count] = '\0'; -- cgit v1.2.3-59-g8ed1b From de78fc5ac1702059ca13203010fd0a3dd20d426f Mon Sep 17 00:00:00 2001 From: Shannon Nelson Date: Sat, 21 Feb 2015 06:41:47 +0000 Subject: i40e: fix shift precedence issue Add parens to make sure the shift and bitwise precedences don't work backwards for us. Change-ID: I60c10ef4fad6bc654522b9d8a53da2e270a0f268 Reported-by: Joe Perches Signed-off-by: Shannon Nelson Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_common.c | 5 +++-- drivers/net/ethernet/intel/i40e/i40e_dcb_nl.c | 2 +- 2 files changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_common.c b/drivers/net/ethernet/intel/i40e/i40e_common.c index 11a9ffebf8d8..2a705a116227 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_common.c +++ b/drivers/net/ethernet/intel/i40e/i40e_common.c @@ -868,8 +868,9 @@ i40e_status i40e_pf_reset(struct i40e_hw *hw) * The grst delay value is in 100ms units, and we'll wait a * couple counts longer to be sure we don't just miss the end. */ - grst_del = rd32(hw, I40E_GLGEN_RSTCTL) & I40E_GLGEN_RSTCTL_GRSTDEL_MASK - >> I40E_GLGEN_RSTCTL_GRSTDEL_SHIFT; + grst_del = (rd32(hw, I40E_GLGEN_RSTCTL) & + I40E_GLGEN_RSTCTL_GRSTDEL_MASK) >> + I40E_GLGEN_RSTCTL_GRSTDEL_SHIFT; for (cnt = 0; cnt < grst_del + 2; cnt++) { reg = rd32(hw, I40E_GLGEN_RSTAT); if (!(reg & I40E_GLGEN_RSTAT_DEVSTATE_MASK)) diff --git a/drivers/net/ethernet/intel/i40e/i40e_dcb_nl.c b/drivers/net/ethernet/intel/i40e/i40e_dcb_nl.c index 183dcb63ce98..a11c70ca5a28 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_dcb_nl.c +++ b/drivers/net/ethernet/intel/i40e/i40e_dcb_nl.c @@ -40,7 +40,7 @@ static void i40e_get_pfc_delay(struct i40e_hw *hw, u16 *delay) u32 val; val = rd32(hw, I40E_PRTDCB_GENC); - *delay = (u16)(val & I40E_PRTDCB_GENC_PFCLDA_MASK >> + *delay = (u16)((val & I40E_PRTDCB_GENC_PFCLDA_MASK) >> I40E_PRTDCB_GENC_PFCLDA_SHIFT); } -- cgit v1.2.3-59-g8ed1b From b67a03357cab0ccb91d641fead6f167c697a24cb Mon Sep 17 00:00:00 2001 From: Akeem G Abodunrin Date: Sat, 21 Feb 2015 06:42:15 +0000 Subject: i40e: Don't check for Tx hang when PF down This patch adds check to bail out if device is already down when checking for Tx hang subtask. Change-ID: I3853fb7a6d11cb9a4c349b687cb25c15b19977a0 Signed-off-by: Akeem G Abodunrin Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_main.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index cbe281be1c9f..6bb637653d12 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -5587,7 +5587,8 @@ static void i40e_check_hang_subtask(struct i40e_pf *pf) int i, v; /* If we're down or resetting, just bail */ - if (test_bit(__I40E_CONFIG_BUSY, &pf->state)) + if (test_bit(__I40E_DOWN, &pf->state) || + test_bit(__I40E_CONFIG_BUSY, &pf->state)) return; /* for each VSI/netdev -- cgit v1.2.3-59-g8ed1b From 71da61976ec18fb57b3ba9a1dd846b747cc7c884 Mon Sep 17 00:00:00 2001 From: Anjali Singhai Date: Sat, 21 Feb 2015 06:42:35 +0000 Subject: i40e: Fix TSO with more than 8 frags per segment issue The hardware has some limitations the driver needs to adhere to, that we found in extended testing. 1) no more than 8 descriptors per packet on the wire 2) no header can span more than 3 descriptors If one of these events occurs, the hardware will generate an internal error and freeze the Tx queue. This patch linearizes the skb to avoid these situations. Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115 Signed-off-by: Anjali Singhai Jain Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_txrx.c | 65 +++++++++++++++++++++++++++ drivers/net/ethernet/intel/i40e/i40e_txrx.h | 1 + drivers/net/ethernet/intel/i40evf/i40e_txrx.c | 65 +++++++++++++++++++++++++++ drivers/net/ethernet/intel/i40evf/i40e_txrx.h | 1 + 4 files changed, 132 insertions(+) diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c index 2206d2d36f0f..0aad61170f75 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c @@ -2139,6 +2139,67 @@ static int i40e_maybe_stop_tx(struct i40e_ring *tx_ring, int size) return __i40e_maybe_stop_tx(tx_ring, size); } +/** + * i40e_chk_linearize - Check if there are more than 8 fragments per packet + * @skb: send buffer + * @tx_flags: collected send information + * @hdr_len: size of the packet header + * + * Note: Our HW can't scatter-gather more than 8 fragments to build + * a packet on the wire and so we need to figure out the cases where we + * need to linearize the skb. + **/ +static bool i40e_chk_linearize(struct sk_buff *skb, u32 tx_flags, + const u8 hdr_len) +{ + struct skb_frag_struct *frag; + bool linearize = false; + unsigned int size = 0; + u16 num_frags; + u16 gso_segs; + + num_frags = skb_shinfo(skb)->nr_frags; + gso_segs = skb_shinfo(skb)->gso_segs; + + if (tx_flags & (I40E_TX_FLAGS_TSO | I40E_TX_FLAGS_FSO)) { + u16 j = 1; + + if (num_frags < (I40E_MAX_BUFFER_TXD)) + goto linearize_chk_done; + /* try the simple math, if we have too many frags per segment */ + if (DIV_ROUND_UP((num_frags + gso_segs), gso_segs) > + I40E_MAX_BUFFER_TXD) { + linearize = true; + goto linearize_chk_done; + } + frag = &skb_shinfo(skb)->frags[0]; + size = hdr_len; + /* we might still have more fragments per segment */ + do { + size += skb_frag_size(frag); + frag++; j++; + if (j == I40E_MAX_BUFFER_TXD) { + if (size < skb_shinfo(skb)->gso_size) { + linearize = true; + break; + } + j = 1; + size -= skb_shinfo(skb)->gso_size; + if (size) + j++; + size += hdr_len; + } + num_frags--; + } while (num_frags); + } else { + if (num_frags >= I40E_MAX_BUFFER_TXD) + linearize = true; + } + +linearize_chk_done: + return linearize; +} + /** * i40e_tx_map - Build the Tx descriptor * @tx_ring: ring to send buffer on @@ -2396,6 +2457,10 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb, if (tsyn) tx_flags |= I40E_TX_FLAGS_TSYN; + if (i40e_chk_linearize(skb, tx_flags, hdr_len)) + if (skb_linearize(skb)) + goto out_drop; + skb_tx_timestamp(skb); /* always enable CRC insertion offload */ diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.h b/drivers/net/ethernet/intel/i40e/i40e_txrx.h index 18b00231d2f1..dff0baeb1ecc 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_txrx.h +++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.h @@ -112,6 +112,7 @@ enum i40e_dyn_idx_t { #define i40e_rx_desc i40e_32byte_rx_desc +#define I40E_MAX_BUFFER_TXD 8 #define I40E_MIN_TX_LEN 17 #define I40E_MAX_DATA_PER_TXD 8192 diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c index 29004382f462..1320a433b8ed 100644 --- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c @@ -1380,6 +1380,67 @@ static void i40e_create_tx_ctx(struct i40e_ring *tx_ring, context_desc->type_cmd_tso_mss = cpu_to_le64(cd_type_cmd_tso_mss); } + /** + * i40e_chk_linearize - Check if there are more than 8 fragments per packet + * @skb: send buffer + * @tx_flags: collected send information + * @hdr_len: size of the packet header + * + * Note: Our HW can't scatter-gather more than 8 fragments to build + * a packet on the wire and so we need to figure out the cases where we + * need to linearize the skb. + **/ +static bool i40e_chk_linearize(struct sk_buff *skb, u32 tx_flags, + const u8 hdr_len) +{ + struct skb_frag_struct *frag; + bool linearize = false; + unsigned int size = 0; + u16 num_frags; + u16 gso_segs; + + num_frags = skb_shinfo(skb)->nr_frags; + gso_segs = skb_shinfo(skb)->gso_segs; + + if (tx_flags & (I40E_TX_FLAGS_TSO | I40E_TX_FLAGS_FSO)) { + u16 j = 1; + + if (num_frags < (I40E_MAX_BUFFER_TXD)) + goto linearize_chk_done; + /* try the simple math, if we have too many frags per segment */ + if (DIV_ROUND_UP((num_frags + gso_segs), gso_segs) > + I40E_MAX_BUFFER_TXD) { + linearize = true; + goto linearize_chk_done; + } + frag = &skb_shinfo(skb)->frags[0]; + size = hdr_len; + /* we might still have more fragments per segment */ + do { + size += skb_frag_size(frag); + frag++; j++; + if (j == I40E_MAX_BUFFER_TXD) { + if (size < skb_shinfo(skb)->gso_size) { + linearize = true; + break; + } + j = 1; + size -= skb_shinfo(skb)->gso_size; + if (size) + j++; + size += hdr_len; + } + num_frags--; + } while (num_frags); + } else { + if (num_frags >= I40E_MAX_BUFFER_TXD) + linearize = true; + } + +linearize_chk_done: + return linearize; +} + /** * i40e_tx_map - Build the Tx descriptor * @tx_ring: ring to send buffer on @@ -1654,6 +1715,10 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb, else if (tso) tx_flags |= I40E_TX_FLAGS_TSO; + if (i40e_chk_linearize(skb, tx_flags, hdr_len)) + if (skb_linearize(skb)) + goto out_drop; + skb_tx_timestamp(skb); /* always enable CRC insertion offload */ diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h index 4e15903b2b6d..c950a038237c 100644 --- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h +++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h @@ -112,6 +112,7 @@ enum i40e_dyn_idx_t { #define i40e_rx_desc i40e_32byte_rx_desc +#define I40E_MAX_BUFFER_TXD 8 #define I40E_MIN_TX_LEN 17 #define I40E_MAX_DATA_PER_TXD 8192 -- cgit v1.2.3-59-g8ed1b From a68de58d2791dd9f2b159703b70377011b35a568 Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Tue, 24 Feb 2015 05:26:03 +0000 Subject: i40e: fix race in hang check The driver was having some issues with false Tx hang detection. This makes the driver a little more direct with the checks for progress forward by directly checking the head write back address and tail register when determining progress. This avoids Tx hangs where the software gets behind, because we are directly checking hardware state when determining hang state. Change-ID: I774f0e861c9e8ab5ccb213634100fe15440ae24a Signed-off-by: Jesse Brandeburg Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_txrx.c | 54 +++++++++++++++------------ drivers/net/ethernet/intel/i40evf/i40e_txrx.c | 54 +++++++++++++++------------ 2 files changed, 60 insertions(+), 48 deletions(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c index 0aad61170f75..bbf1b1247ac4 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c @@ -585,6 +585,20 @@ void i40e_free_tx_resources(struct i40e_ring *tx_ring) } } +/** + * i40e_get_head - Retrieve head from head writeback + * @tx_ring: tx ring to fetch head of + * + * Returns value of Tx ring head based on value stored + * in head write-back location + **/ +static inline u32 i40e_get_head(struct i40e_ring *tx_ring) +{ + void *head = (struct i40e_tx_desc *)tx_ring->desc + tx_ring->count; + + return le32_to_cpu(*(volatile __le32 *)head); +} + /** * i40e_get_tx_pending - how many tx descriptors not processed * @tx_ring: the ring of descriptors @@ -594,10 +608,16 @@ void i40e_free_tx_resources(struct i40e_ring *tx_ring) **/ static u32 i40e_get_tx_pending(struct i40e_ring *ring) { - u32 ntu = ((ring->next_to_clean <= ring->next_to_use) - ? ring->next_to_use - : ring->next_to_use + ring->count); - return ntu - ring->next_to_clean; + u32 head, tail; + + head = i40e_get_head(ring); + tail = readl(ring->tail); + + if (head != tail) + return (head < tail) ? + tail - head : (tail + ring->count - head); + + return 0; } /** @@ -606,6 +626,8 @@ static u32 i40e_get_tx_pending(struct i40e_ring *ring) **/ static bool i40e_check_tx_hang(struct i40e_ring *tx_ring) { + u32 tx_done = tx_ring->stats.packets; + u32 tx_done_old = tx_ring->tx_stats.tx_done_old; u32 tx_pending = i40e_get_tx_pending(tx_ring); struct i40e_pf *pf = tx_ring->vsi->back; bool ret = false; @@ -623,41 +645,25 @@ static bool i40e_check_tx_hang(struct i40e_ring *tx_ring) * run the check_tx_hang logic with a transmit completion * pending but without time to complete it yet. */ - if ((tx_ring->tx_stats.tx_done_old == tx_ring->stats.packets) && - (tx_pending >= I40E_MIN_DESC_PENDING)) { + if ((tx_done_old == tx_done) && tx_pending) { /* make sure it is true for two checks in a row */ ret = test_and_set_bit(__I40E_HANG_CHECK_ARMED, &tx_ring->state); - } else if ((tx_ring->tx_stats.tx_done_old == tx_ring->stats.packets) && - (tx_pending < I40E_MIN_DESC_PENDING) && - (tx_pending > 0)) { + } else if (tx_done_old == tx_done && + (tx_pending < I40E_MIN_DESC_PENDING) && (tx_pending > 0)) { if (I40E_DEBUG_FLOW & pf->hw.debug_mask) dev_info(tx_ring->dev, "HW needs some more descs to do a cacheline flush. tx_pending %d, queue %d", tx_pending, tx_ring->queue_index); pf->tx_sluggish_count++; } else { /* update completed stats and disarm the hang check */ - tx_ring->tx_stats.tx_done_old = tx_ring->stats.packets; + tx_ring->tx_stats.tx_done_old = tx_done; clear_bit(__I40E_HANG_CHECK_ARMED, &tx_ring->state); } return ret; } -/** - * i40e_get_head - Retrieve head from head writeback - * @tx_ring: tx ring to fetch head of - * - * Returns value of Tx ring head based on value stored - * in head write-back location - **/ -static inline u32 i40e_get_head(struct i40e_ring *tx_ring) -{ - void *head = (struct i40e_tx_desc *)tx_ring->desc + tx_ring->count; - - return le32_to_cpu(*(volatile __le32 *)head); -} - #define WB_STRIDE 0x3 /** diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c index 1320a433b8ed..be05829ba619 100644 --- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c @@ -125,6 +125,20 @@ void i40evf_free_tx_resources(struct i40e_ring *tx_ring) } } +/** + * i40e_get_head - Retrieve head from head writeback + * @tx_ring: tx ring to fetch head of + * + * Returns value of Tx ring head based on value stored + * in head write-back location + **/ +static inline u32 i40e_get_head(struct i40e_ring *tx_ring) +{ + void *head = (struct i40e_tx_desc *)tx_ring->desc + tx_ring->count; + + return le32_to_cpu(*(volatile __le32 *)head); +} + /** * i40e_get_tx_pending - how many tx descriptors not processed * @tx_ring: the ring of descriptors @@ -134,10 +148,16 @@ void i40evf_free_tx_resources(struct i40e_ring *tx_ring) **/ static u32 i40e_get_tx_pending(struct i40e_ring *ring) { - u32 ntu = ((ring->next_to_clean <= ring->next_to_use) - ? ring->next_to_use - : ring->next_to_use + ring->count); - return ntu - ring->next_to_clean; + u32 head, tail; + + head = i40e_get_head(ring); + tail = readl(ring->tail); + + if (head != tail) + return (head < tail) ? + tail - head : (tail + ring->count - head); + + return 0; } /** @@ -146,6 +166,8 @@ static u32 i40e_get_tx_pending(struct i40e_ring *ring) **/ static bool i40e_check_tx_hang(struct i40e_ring *tx_ring) { + u32 tx_done = tx_ring->stats.packets; + u32 tx_done_old = tx_ring->tx_stats.tx_done_old; u32 tx_pending = i40e_get_tx_pending(tx_ring); bool ret = false; @@ -162,36 +184,20 @@ static bool i40e_check_tx_hang(struct i40e_ring *tx_ring) * run the check_tx_hang logic with a transmit completion * pending but without time to complete it yet. */ - if ((tx_ring->tx_stats.tx_done_old == tx_ring->stats.packets) && - (tx_pending >= I40E_MIN_DESC_PENDING)) { + if ((tx_done_old == tx_done) && tx_pending) { /* make sure it is true for two checks in a row */ ret = test_and_set_bit(__I40E_HANG_CHECK_ARMED, &tx_ring->state); - } else if (!(tx_ring->tx_stats.tx_done_old == tx_ring->stats.packets) || - !(tx_pending < I40E_MIN_DESC_PENDING) || - !(tx_pending > 0)) { + } else if (tx_done_old == tx_done && + (tx_pending < I40E_MIN_DESC_PENDING) && (tx_pending > 0)) { /* update completed stats and disarm the hang check */ - tx_ring->tx_stats.tx_done_old = tx_ring->stats.packets; + tx_ring->tx_stats.tx_done_old = tx_done; clear_bit(__I40E_HANG_CHECK_ARMED, &tx_ring->state); } return ret; } -/** - * i40e_get_head - Retrieve head from head writeback - * @tx_ring: tx ring to fetch head of - * - * Returns value of Tx ring head based on value stored - * in head write-back location - **/ -static inline u32 i40e_get_head(struct i40e_ring *tx_ring) -{ - void *head = (struct i40e_tx_desc *)tx_ring->desc + tx_ring->count; - - return le32_to_cpu(*(volatile __le32 *)head); -} - #define WB_STRIDE 0x3 /** -- cgit v1.2.3-59-g8ed1b From 7f9ff47683cb7441e6d0496365bcf64738f6d2d4 Mon Sep 17 00:00:00 2001 From: Anjali Singhai Date: Sat, 21 Feb 2015 06:43:19 +0000 Subject: i40e: Fix the case where per TC queue count was higher than queues enabled When the driver or hardware gets less interrupt vectors than the actual number of CPU cores, limit the queue count for the priority queue traffic class (TC) queues. This will fix a warning with multiple function mode where systems regularly have more cores than vectors. Also add extra comment for readability. Change-ID: I4f02226263aa3995e1f5ee5503eac0cd6ee12fbd Signed-off-by: Anjali Singhai Jain Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_main.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index 6bb637653d12..a926e3bf1d6d 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -1512,7 +1512,12 @@ static void i40e_vsi_setup_queue_map(struct i40e_vsi *vsi, vsi->tc_config.numtc = numtc; vsi->tc_config.enabled_tc = enabled_tc ? enabled_tc : 1; /* Number of queues per enabled TC */ - num_tc_qps = vsi->alloc_queue_pairs/numtc; + /* In MFP case we can have a much lower count of MSIx + * vectors available and so we need to lower the used + * q count. + */ + qcount = min_t(int, vsi->alloc_queue_pairs, pf->num_lan_msix); + num_tc_qps = qcount / numtc; num_tc_qps = min_t(int, num_tc_qps, I40E_MAX_QUEUES_PER_TC); /* Setup queue offset/count for all TCs for given VSI */ -- cgit v1.2.3-59-g8ed1b From cd238a3ecf2bf7f3d1a155a32b4bddd87dbd3d23 Mon Sep 17 00:00:00 2001 From: "Parikh, Neerav" Date: Sat, 21 Feb 2015 06:43:37 +0000 Subject: i40e: Fix the Tx ring qset handle when DCB reconfigures When DCB is reconfigured to single TC the driver did not reset the Tx ring Qset handle to the correct mapping; which caused Tx queue disable timeouts. Change-ID: I4da5915ec92a83c281b478d653fae6ef1b72edfe Signed-off-by: Neerav Parikh Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_main.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index a926e3bf1d6d..bd4494d727a6 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -2689,8 +2689,15 @@ static void i40e_vsi_config_dcb_rings(struct i40e_vsi *vsi) u16 qoffset, qcount; int i, n; - if (!(vsi->back->flags & I40E_FLAG_DCB_ENABLED)) - return; + if (!(vsi->back->flags & I40E_FLAG_DCB_ENABLED)) { + /* Reset the TC information */ + for (i = 0; i < vsi->num_queue_pairs; i++) { + rx_ring = vsi->rx_rings[i]; + tx_ring = vsi->tx_rings[i]; + rx_ring->dcb_tc = 0; + tx_ring->dcb_tc = 0; + } + } for (n = 0; n < I40E_MAX_TRAFFIC_CLASS; n++) { if (!(vsi->tc_config.enabled_tc & (1 << n))) -- cgit v1.2.3-59-g8ed1b From 11e4770842d4917b1cad52d901b758a6d1997735 Mon Sep 17 00:00:00 2001 From: "Parikh, Neerav" Date: Sat, 21 Feb 2015 06:43:55 +0000 Subject: i40e: Issue a PF reset if Tx queue disable timeout As part of DCB reconfiguration flow if the Tx queue disable times out then issue a PF reset to do some level of recovery. Change-ID: I7550021c55bff355351c0365e61e1f05fcaff46d Signed-off-by: Neerav Parikh Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_main.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index bd4494d727a6..9751465f29c7 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -5266,8 +5266,14 @@ static int i40e_handle_lldp_event(struct i40e_pf *pf, /* Wait for the PF's Tx queues to be disabled */ ret = i40e_pf_wait_txq_disabled(pf); - if (!ret) + if (ret) { + /* Schedule PF reset to recover */ + set_bit(__I40E_PF_RESET_REQUESTED, &pf->state); + i40e_service_event_schedule(pf); + } else { i40e_pf_unquiesce_all_vsi(pf); + } + exit: return ret; } -- cgit v1.2.3-59-g8ed1b From 85e76d0312a373a1268b88a7a442c6004e0c6063 Mon Sep 17 00:00:00 2001 From: Anjali Singhai Date: Sat, 21 Feb 2015 06:44:16 +0000 Subject: i40evf: TCP/IPv6 over Vxlan Tx checksum offload fix We were checking the outer Protocol flags and deciding the flow for inner header. This patch fixes that. This fixes the Tx checksum offload for TCP/IPv6 over vxlan. Change-ID: I837aaea921d34f71b24c2bc32aaadea5001ddf78 Signed-off-by: Anjali Singhai Jain Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40evf/i40e_txrx.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c index be05829ba619..708891571dae 100644 --- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c @@ -1212,17 +1212,16 @@ static int i40e_tso(struct i40e_ring *tx_ring, struct sk_buff *skb, if (err < 0) return err; - if (protocol == htons(ETH_P_IP)) { - iph = skb->encapsulation ? inner_ip_hdr(skb) : ip_hdr(skb); + iph = skb->encapsulation ? inner_ip_hdr(skb) : ip_hdr(skb); + ipv6h = skb->encapsulation ? inner_ipv6_hdr(skb) : ipv6_hdr(skb); + + if (iph->version == 4) { tcph = skb->encapsulation ? inner_tcp_hdr(skb) : tcp_hdr(skb); iph->tot_len = 0; iph->check = 0; tcph->check = ~csum_tcpudp_magic(iph->saddr, iph->daddr, 0, IPPROTO_TCP, 0); - } else if (skb_is_gso_v6(skb)) { - - ipv6h = skb->encapsulation ? inner_ipv6_hdr(skb) - : ipv6_hdr(skb); + } else if (ipv6h->version == 6) { tcph = skb->encapsulation ? inner_tcp_hdr(skb) : tcp_hdr(skb); ipv6h->payload_len = 0; tcph->check = ~csum_ipv6_magic(&ipv6h->saddr, &ipv6h->daddr, @@ -1280,13 +1279,9 @@ static void i40e_tx_enable_csum(struct sk_buff *skb, u32 tx_flags, I40E_TX_CTX_EXT_IP_IPV4_NO_CSUM; } } else if (tx_flags & I40E_TX_FLAGS_IPV6) { - if (tx_flags & I40E_TX_FLAGS_TSO) { - *cd_tunneling |= I40E_TX_CTX_EXT_IP_IPV6; + *cd_tunneling |= I40E_TX_CTX_EXT_IP_IPV6; + if (tx_flags & I40E_TX_FLAGS_TSO) ip_hdr(skb)->check = 0; - } else { - *cd_tunneling |= - I40E_TX_CTX_EXT_IP_IPV4_NO_CSUM; - } } /* Now set the ctx descriptor fields */ @@ -1296,6 +1291,11 @@ static void i40e_tx_enable_csum(struct sk_buff *skb, u32 tx_flags, ((skb_inner_network_offset(skb) - skb_transport_offset(skb)) >> 1) << I40E_TXD_CTX_QW0_NATLEN_SHIFT; + if (this_ip_hdr->version == 6) { + tx_flags &= ~I40E_TX_FLAGS_IPV4; + tx_flags |= I40E_TX_FLAGS_IPV6; + } + } else { network_hdr_len = skb_network_header_len(skb); -- cgit v1.2.3-59-g8ed1b From e147758d9aef1e41dad331b21df206200cf16e80 Mon Sep 17 00:00:00 2001 From: Shannon Nelson Date: Sat, 21 Feb 2015 06:44:33 +0000 Subject: i40e: disconnect irqs on shutdown Combine the ICR0 shutdown with the standard interrupt shutdown, and add the interrupt clearing to the PCI shutdown path. This prevents the driver from allowing stray interrupts or causing system logs from un-handled interrupts. Change-ID: I48f6ab95cad7f8ca77c1f26c92a51cc1034ced43 Signed-off-by: Shannon Nelson Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_main.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index 9751465f29c7..8bfd2545122d 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -3842,6 +3842,12 @@ static void i40e_clear_interrupt_scheme(struct i40e_pf *pf) { int i; + i40e_stop_misc_vector(pf); + if (pf->flags & I40E_FLAG_MSIX_ENABLED) { + synchronize_irq(pf->msix_entries[0].vector); + free_irq(pf->msix_entries[0].vector, pf); + } + i40e_put_lump(pf->irq_pile, 0, I40E_PILE_VALID_BIT-1); for (i = 0; i < pf->num_alloc_vsi; i++) if (pf->vsi[i]) @@ -9578,12 +9584,6 @@ static void i40e_remove(struct pci_dev *pdev) if (pf->vsi[pf->lan_vsi]) i40e_vsi_release(pf->vsi[pf->lan_vsi]); - i40e_stop_misc_vector(pf); - if (pf->flags & I40E_FLAG_MSIX_ENABLED) { - synchronize_irq(pf->msix_entries[0].vector); - free_irq(pf->msix_entries[0].vector, pf); - } - /* shutdown and destroy the HMC */ if (pf->hw.hmc.hmc_obj) { ret_code = i40e_shutdown_lan_hmc(&pf->hw); @@ -9737,6 +9737,8 @@ static void i40e_shutdown(struct pci_dev *pdev) wr32(hw, I40E_PFPM_APM, (pf->wol_en ? I40E_PFPM_APM_APME_MASK : 0)); wr32(hw, I40E_PFPM_WUFC, (pf->wol_en ? I40E_PFPM_WUFC_MAG_MASK : 0)); + i40e_clear_interrupt_scheme(pf); + if (system_state == SYSTEM_POWER_OFF) { pci_wake_from_d3(pdev, pf->wol_en); pci_set_power_state(pdev, PCI_D3hot); -- cgit v1.2.3-59-g8ed1b From 33c62b34e5a3d57eb8a487140ca46631fc76e10c Mon Sep 17 00:00:00 2001 From: Mitch A Williams Date: Sat, 21 Feb 2015 06:44:51 +0000 Subject: i40e: stop flow director on shutdown In some cases, the hardware would continue to try to access the FDIR ring after entering D3Hot state, which would cause either PCIe errors or NMIs, depending upon system configuration. Explicitly stop FDIR in our shutdown routine to eliminate this possibility. Change-ID: I1bd9fc7fd8f151fe24cad132ac9adddab923e3af Signed-off-by: Mitch Williams Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_main.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index 8bfd2545122d..dadda3c5d658 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -9558,6 +9558,7 @@ static void i40e_remove(struct pci_dev *pdev) set_bit(__I40E_DOWN, &pf->state); del_timer_sync(&pf->service_timer); cancel_work_sync(&pf->service_task); + i40e_fdir_teardown(pf); if (pf->flags & I40E_FLAG_SRIOV_ENABLED) { i40e_free_vfs(pf); -- cgit v1.2.3-59-g8ed1b From 2c47e351f61b66f2e870bfd634e471a6ab1af920 Mon Sep 17 00:00:00 2001 From: Shannon Nelson Date: Sat, 21 Feb 2015 06:45:10 +0000 Subject: i40e: catch NVM write semaphore timeout and retry In some circumstances, a multi-write transaction takes longer than the default 3 minute timeout on the write semaphore. If the write failed with an EBUSY status, this is likely the problem, so here we try to reacquire the semaphore then retry the write. We only do one retry, then give up. Change-ID: I1c8be60688acc2f39573839579baf601207c4a36 Signed-off-by: Shannon Nelson Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_nvm.c | 35 ++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) diff --git a/drivers/net/ethernet/intel/i40e/i40e_nvm.c b/drivers/net/ethernet/intel/i40e/i40e_nvm.c index 3e70f2e45a47..5defe0d63514 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_nvm.c +++ b/drivers/net/ethernet/intel/i40e/i40e_nvm.c @@ -679,9 +679,11 @@ static i40e_status i40e_nvmupd_state_writing(struct i40e_hw *hw, { i40e_status status; enum i40e_nvmupd_cmd upd_cmd; + bool retry_attempt = false; upd_cmd = i40e_nvmupd_validate_command(hw, cmd, errno); +retry: switch (upd_cmd) { case I40E_NVMUPD_WRITE_CON: status = i40e_nvmupd_nvm_write(hw, cmd, bytes, errno); @@ -725,6 +727,39 @@ static i40e_status i40e_nvmupd_state_writing(struct i40e_hw *hw, *errno = -ESRCH; break; } + + /* In some circumstances, a multi-write transaction takes longer + * than the default 3 minute timeout on the write semaphore. If + * the write failed with an EBUSY status, this is likely the problem, + * so here we try to reacquire the semaphore then retry the write. + * We only do one retry, then give up. + */ + if (status && (hw->aq.asq_last_status == I40E_AQ_RC_EBUSY) && + !retry_attempt) { + i40e_status old_status = status; + u32 old_asq_status = hw->aq.asq_last_status; + u32 gtime; + + gtime = rd32(hw, I40E_GLVFGEN_TIMER); + if (gtime >= hw->nvm.hw_semaphore_timeout) { + i40e_debug(hw, I40E_DEBUG_ALL, + "NVMUPD: write semaphore expired (%d >= %lld), retrying\n", + gtime, hw->nvm.hw_semaphore_timeout); + i40e_release_nvm(hw); + status = i40e_acquire_nvm(hw, I40E_RESOURCE_WRITE); + if (status) { + i40e_debug(hw, I40E_DEBUG_ALL, + "NVMUPD: write semaphore reacquire failed aq_err = %d\n", + hw->aq.asq_last_status); + status = old_status; + hw->aq.asq_last_status = old_asq_status; + } else { + retry_attempt = true; + goto retry; + } + } + } + return status; } -- cgit v1.2.3-59-g8ed1b From 65d13461d7c3fa822ff2000d2c0fe5f5b1943cb9 Mon Sep 17 00:00:00 2001 From: Shannon Nelson Date: Sat, 21 Feb 2015 06:45:28 +0000 Subject: i40e: check pointers before use Make sure we don't try to dereference NULL pointers when returning values from the AdminQ calls. Change-ID: Ia6694f2f415d50acf0aba063c863568742799aff Signed-off-by: Shannon Nelson Tested-by: Jim Young Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/i40e/i40e_common.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_common.c b/drivers/net/ethernet/intel/i40e/i40e_common.c index 2a705a116227..6aea65dae5ed 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_common.c +++ b/drivers/net/ethernet/intel/i40e/i40e_common.c @@ -2847,7 +2847,7 @@ i40e_status i40e_aq_add_udp_tunnel(struct i40e_hw *hw, status = i40e_asq_send_command(hw, &desc, NULL, 0, cmd_details); - if (!status) + if (!status && filter_index) *filter_index = resp->index; return status; -- cgit v1.2.3-59-g8ed1b From 0bb59cb00e002d17bb337410a45c62023ee78fc9 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Wed, 25 Feb 2015 18:44:51 +0100 Subject: drm: atmel-hlcdc: remove clock polarity from crtc driver Remove this configuration bit in crtc driver as the rising edge clock is widely used. Signed-off-by: Boris Brezillon Signed-off-by: Nicolas Ferre --- drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c index 0409b907de5d..b3e3068c6ec0 100644 --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c @@ -153,7 +153,7 @@ static int atmel_hlcdc_crtc_mode_set(struct drm_crtc *c, (adj->crtc_hdisplay - 1) | ((adj->crtc_vdisplay - 1) << 16)); - cfg = ATMEL_HLCDC_CLKPOL; + cfg = 0; prate = clk_get_rate(crtc->dc->hlcdc->sys_clk); mode_rate = mode->crtc_clock * 1000; -- cgit v1.2.3-59-g8ed1b From 4a3a6f86693922b29cf829c63f652b057f14619e Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 24 Feb 2015 15:14:45 +0100 Subject: ARM: multi_v7_defconfig: Enable shmobile platforms Enable support for shmobile platforms that became multi-platform aware. Several non-critical drivers and subsystems are built as modules, to keep kernel size reasonable. Tested on: - r8a73a4/ape6evm: - U-Boot fails with "Error: unrecognized/unsupported machine ID", - kexec works. - r8a7740/armadillo: - Hermit boot loader fails (larger image, more memory corruption), - kexec works. - r8a7791/koelsch, - sh73a0/kzm9g: - zImage+DTB from U-Boot needs CONFIG_ARM_ATAG_DTB_COMPAT=n, - kexec works. - am335x/boneblack. Signed-off-by: Geert Uytterhoeven Acked-by: Simon Horman Signed-off-by: Arnd Bergmann --- arch/arm/configs/multi_v7_defconfig | 82 ++++++++++++++++++++++++++++++++++--- 1 file changed, 77 insertions(+), 5 deletions(-) diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index e8a4c955241b..b7e6b6fba5e0 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -62,6 +62,17 @@ CONFIG_MACH_SPEAR1340=y CONFIG_ARCH_STI=y CONFIG_ARCH_EXYNOS=y CONFIG_EXYNOS5420_MCPM=y +CONFIG_ARCH_SHMOBILE_MULTI=y +CONFIG_ARCH_EMEV2=y +CONFIG_ARCH_R7S72100=y +CONFIG_ARCH_R8A73A4=y +CONFIG_ARCH_R8A7740=y +CONFIG_ARCH_R8A7779=y +CONFIG_ARCH_R8A7790=y +CONFIG_ARCH_R8A7791=y +CONFIG_ARCH_R8A7794=y +CONFIG_ARCH_SH73A0=y +CONFIG_MACH_MARZEN=y CONFIG_ARCH_SUNXI=y CONFIG_ARCH_SIRF=y CONFIG_ARCH_TEGRA=y @@ -84,6 +95,8 @@ CONFIG_PCI_KEYSTONE=y CONFIG_PCI_MSI=y CONFIG_PCI_MVEBU=y CONFIG_PCI_TEGRA=y +CONFIG_PCI_RCAR_GEN2=y +CONFIG_PCI_RCAR_GEN2_PCIE=y CONFIG_PCIEPORTBUS=y CONFIG_SMP=y CONFIG_NR_CPUS=8 @@ -130,6 +143,7 @@ CONFIG_DEVTMPFS_MOUNT=y CONFIG_DMA_CMA=y CONFIG_CMA_SIZE_MBYTES=64 CONFIG_OMAP_OCP2SCP=y +CONFIG_SIMPLE_PM_BUS=y CONFIG_MTD=y CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_BLOCK=y @@ -157,6 +171,7 @@ CONFIG_AHCI_SUNXI=y CONFIG_AHCI_TEGRA=y CONFIG_SATA_HIGHBANK=y CONFIG_SATA_MV=y +CONFIG_SATA_RCAR=y CONFIG_NETDEVICES=y CONFIG_HIX5HD2_GMAC=y CONFIG_SUN4I_EMAC=y @@ -167,14 +182,17 @@ CONFIG_MV643XX_ETH=y CONFIG_MVNETA=y CONFIG_KS8851=y CONFIG_R8169=y +CONFIG_SH_ETH=y CONFIG_SMSC911X=y CONFIG_STMMAC_ETH=y CONFIG_TI_CPSW=y CONFIG_XILINX_EMACLITE=y CONFIG_AT803X_PHY=y CONFIG_MARVELL_PHY=y +CONFIG_SMSC_PHY=y CONFIG_BROADCOM_PHY=y CONFIG_ICPLUS_PHY=y +CONFIG_MICREL_PHY=y CONFIG_USB_PEGASUS=y CONFIG_USB_USBNET=y CONFIG_USB_NET_SMSC75XX=y @@ -192,15 +210,18 @@ CONFIG_KEYBOARD_CROS_EC=y CONFIG_MOUSE_PS2_ELANTECH=y CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_ATMEL_MXT=y +CONFIG_TOUCHSCREEN_ST1232=m CONFIG_TOUCHSCREEN_STMPE=y CONFIG_TOUCHSCREEN_SUN4I=y CONFIG_INPUT_MISC=y CONFIG_INPUT_MPU3050=y CONFIG_INPUT_AXP20X_PEK=y +CONFIG_INPUT_ADXL34X=m CONFIG_SERIO_AMBAKMI=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_DW=y +CONFIG_SERIAL_8250_EM=y CONFIG_SERIAL_8250_MT6577=y CONFIG_SERIAL_AMBA_PL011=y CONFIG_SERIAL_AMBA_PL011_CONSOLE=y @@ -213,6 +234,9 @@ CONFIG_SERIAL_SIRFSOC_CONSOLE=y CONFIG_SERIAL_TEGRA=y CONFIG_SERIAL_IMX=y CONFIG_SERIAL_IMX_CONSOLE=y +CONFIG_SERIAL_SH_SCI=y +CONFIG_SERIAL_SH_SCI_NR_UARTS=20 +CONFIG_SERIAL_SH_SCI_CONSOLE=y CONFIG_SERIAL_MSM=y CONFIG_SERIAL_MSM_CONSOLE=y CONFIG_SERIAL_VT8500=y @@ -233,19 +257,26 @@ CONFIG_I2C_MUX_PCA954x=y CONFIG_I2C_MUX_PINCTRL=y CONFIG_I2C_CADENCE=y CONFIG_I2C_DESIGNWARE_PLATFORM=y +CONFIG_I2C_GPIO=m CONFIG_I2C_EXYNOS5=y CONFIG_I2C_MV64XXX=y +CONFIG_I2C_RIIC=y CONFIG_I2C_S3C2410=y +CONFIG_I2C_SH_MOBILE=y CONFIG_I2C_SIRF=y -CONFIG_I2C_TEGRA=y CONFIG_I2C_ST=y -CONFIG_SPI=y +CONFIG_I2C_TEGRA=y CONFIG_I2C_XILINX=y -CONFIG_SPI_DAVINCI=y +CONFIG_I2C_RCAR=y +CONFIG_SPI=y CONFIG_SPI_CADENCE=y +CONFIG_SPI_DAVINCI=y CONFIG_SPI_OMAP24XX=y CONFIG_SPI_ORION=y CONFIG_SPI_PL022=y +CONFIG_SPI_RSPI=y +CONFIG_SPI_SH_MSIOF=m +CONFIG_SPI_SH_HSPI=y CONFIG_SPI_SIRF=y CONFIG_SPI_SUN4I=y CONFIG_SPI_SUN6I=y @@ -259,12 +290,15 @@ CONFIG_PINCTRL_PALMAS=y CONFIG_PINCTRL_APQ8084=y CONFIG_GPIO_SYSFS=y CONFIG_GPIO_GENERIC_PLATFORM=y -CONFIG_GPIO_DWAPB=y CONFIG_GPIO_DAVINCI=y +CONFIG_GPIO_DWAPB=y +CONFIG_GPIO_EM=y +CONFIG_GPIO_RCAR=y CONFIG_GPIO_XILINX=y CONFIG_GPIO_ZYNQ=y CONFIG_GPIO_PCA953X=y CONFIG_GPIO_PCA953X_IRQ=y +CONFIG_GPIO_PCF857X=y CONFIG_GPIO_TWL4030=y CONFIG_GPIO_PALMAS=y CONFIG_GPIO_SYSCON=y @@ -276,10 +310,12 @@ CONFIG_POWER_RESET_AS3722=y CONFIG_POWER_RESET_GPIO=y CONFIG_POWER_RESET_KEYSTONE=y CONFIG_POWER_RESET_SUN6I=y +CONFIG_POWER_RESET_RMOBILE=y CONFIG_SENSORS_LM90=y CONFIG_SENSORS_LM95245=y CONFIG_THERMAL=y CONFIG_CPU_THERMAL=y +CONFIG_RCAR_THERMAL=y CONFIG_ARMADA_THERMAL=y CONFIG_DAVINCI_WATCHDOG CONFIG_ST_THERMAL_SYSCFG=y @@ -290,6 +326,7 @@ CONFIG_ARM_SP805_WATCHDOG=y CONFIG_ORION_WATCHDOG=y CONFIG_SUNXI_WATCHDOG=y CONFIG_MESON_WATCHDOG=y +CONFIG_MFD_AS3711=y CONFIG_MFD_AS3722=y CONFIG_MFD_BCM590XX=y CONFIG_MFD_AXP20X=y @@ -304,13 +341,16 @@ CONFIG_MFD_TPS65090=y CONFIG_MFD_TPS6586X=y CONFIG_MFD_TPS65910=y CONFIG_REGULATOR_AB8500=y +CONFIG_REGULATOR_AS3711=y CONFIG_REGULATOR_AS3722=y CONFIG_REGULATOR_AXP20X=y CONFIG_REGULATOR_BCM590XX=y +CONFIG_REGULATOR_DA9210=y CONFIG_REGULATOR_GPIO=y CONFIG_MFD_SYSCON=y CONFIG_POWER_RESET_SYSCON=y CONFIG_REGULATOR_MAX8907=y +CONFIG_REGULATOR_MAX8973=y CONFIG_REGULATOR_MAX77686=y CONFIG_REGULATOR_PALMAS=y CONFIG_REGULATOR_S2MPS11=y @@ -324,18 +364,32 @@ CONFIG_REGULATOR_TWL4030=y CONFIG_REGULATOR_VEXPRESS=y CONFIG_MEDIA_SUPPORT=y CONFIG_MEDIA_CAMERA_SUPPORT=y +CONFIG_MEDIA_CONTROLLER=y +CONFIG_VIDEO_V4L2_SUBDEV_API=y CONFIG_MEDIA_USB_SUPPORT=y CONFIG_USB_VIDEO_CLASS=y CONFIG_USB_GSPCA=y +CONFIG_V4L_PLATFORM_DRIVERS=y +CONFIG_SOC_CAMERA=m +CONFIG_SOC_CAMERA_PLATFORM=m +CONFIG_VIDEO_RCAR_VIN=m +CONFIG_V4L_MEM2MEM_DRIVERS=y +CONFIG_VIDEO_RENESAS_VSP1=m +# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set +CONFIG_VIDEO_ADV7180=m CONFIG_DRM=y +CONFIG_DRM_RCAR_DU=m CONFIG_DRM_TEGRA=y CONFIG_DRM_PANEL_SIMPLE=y CONFIG_FB_ARMCLCD=y CONFIG_FB_WM8505=y +CONFIG_FB_SH_MOBILE_LCDC=y CONFIG_FB_SIMPLE=y +CONFIG_FB_SH_MOBILE_MERAM=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=y CONFIG_BACKLIGHT_PWM=y +CONFIG_BACKLIGHT_AS3711=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y CONFIG_SOUND=y @@ -343,6 +397,8 @@ CONFIG_SND=y CONFIG_SND_DYNAMIC_MINORS=y CONFIG_SND_USB_AUDIO=y CONFIG_SND_SOC=y +CONFIG_SND_SOC_SH4_FSI=m +CONFIG_SND_SOC_RCAR=m CONFIG_SND_SOC_TEGRA=y CONFIG_SND_SOC_TEGRA_RT5640=y CONFIG_SND_SOC_TEGRA_WM8753=y @@ -350,6 +406,8 @@ CONFIG_SND_SOC_TEGRA_WM8903=y CONFIG_SND_SOC_TEGRA_TRIMSLICE=y CONFIG_SND_SOC_TEGRA_ALC5632=y CONFIG_SND_SOC_TEGRA_MAX98090=y +CONFIG_SND_SOC_AK4642=m +CONFIG_SND_SOC_WM8978=m CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_MVEBU=y @@ -362,6 +420,8 @@ CONFIG_USB_ISP1760_HCD=y CONFIG_USB_OHCI_HCD=y CONFIG_USB_OHCI_HCD_STI=y CONFIG_USB_OHCI_HCD_PLATFORM=y +CONFIG_USB_R8A66597_HCD=m +CONFIG_USB_RENESAS_USBHS=m CONFIG_USB_STORAGE=y CONFIG_USB_DWC3=y CONFIG_USB_CHIPIDEA=y @@ -374,6 +434,10 @@ CONFIG_SAMSUNG_USB3PHY=y CONFIG_USB_GPIO_VBUS=y CONFIG_USB_ISP1301=y CONFIG_USB_MXS_PHY=y +CONFIG_USB_RCAR_PHY=m +CONFIG_USB_RCAR_GEN2_PHY=m +CONFIG_USB_GADGET=y +CONFIG_USB_RENESAS_USBHS_UDC=m CONFIG_MMC=y CONFIG_MMC_BLOCK_MINORS=16 CONFIG_MMC_ARMMMCI=y @@ -392,12 +456,14 @@ CONFIG_MMC_SDHCI_ST=y CONFIG_MMC_OMAP=y CONFIG_MMC_OMAP_HS=y CONFIG_MMC_MVSDIO=y -CONFIG_MMC_SUNXI=y +CONFIG_MMC_SDHI=y CONFIG_MMC_DW=y CONFIG_MMC_DW_IDMAC=y CONFIG_MMC_DW_PLTFM=y CONFIG_MMC_DW_EXYNOS=y CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SH_MMCIF=y +CONFIG_MMC_SUNXI=y CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y CONFIG_LEDS_GPIO=y @@ -421,10 +487,12 @@ CONFIG_RTC_DRV_AS3722=y CONFIG_RTC_DRV_DS1307=y CONFIG_RTC_DRV_MAX8907=y CONFIG_RTC_DRV_MAX77686=y +CONFIG_RTC_DRV_RS5C372=m CONFIG_RTC_DRV_PALMAS=y CONFIG_RTC_DRV_TWL4030=y CONFIG_RTC_DRV_TPS6586X=y CONFIG_RTC_DRV_TPS65910=y +CONFIG_RTC_DRV_S35390A=m CONFIG_RTC_DRV_EM3027=y CONFIG_RTC_DRV_PL031=y CONFIG_RTC_DRV_VT8500=y @@ -436,6 +504,9 @@ CONFIG_DMADEVICES=y CONFIG_DW_DMAC=y CONFIG_MV_XOR=y CONFIG_TEGRA20_APB_DMA=y +CONFIG_SH_DMAE=y +CONFIG_RCAR_AUDMAC_PP=m +CONFIG_RCAR_DMAC=y CONFIG_STE_DMA40=y CONFIG_SIRF_DMA=y CONFIG_TI_EDMA=y @@ -468,6 +539,7 @@ CONFIG_IIO=y CONFIG_XILINX_XADC=y CONFIG_AK8975=y CONFIG_PWM=y +CONFIG_PWM_RENESAS_TPU=y CONFIG_PWM_TEGRA=y CONFIG_PWM_VT8500=y CONFIG_PHY_HIX5HD2_SATA=y -- cgit v1.2.3-59-g8ed1b From bc4b1f486fe69b86769e07c8edce472327a8462b Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Sun, 15 Feb 2015 11:57:53 +0700 Subject: Revert "USB: serial: make bulk_out_size a lower limit" This reverts commit 5083fd7bdfe6760577235a724cf6dccae13652c2. A bulk-out size smaller than the end-point size is indeed valid. The offending commit broke the usb-debug driver for EHCI debug devices, which use 8-byte buffers. Fixes: 5083fd7bdfe6 ("USB: serial: make bulk_out_size a lower limit") Reported-by: "Li, Elvin" Cc: stable # v3.15 Signed-off-by: Johan Hovold --- drivers/usb/serial/usb-serial.c | 5 +++-- include/linux/usb/serial.h | 3 +-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 475723c006f9..19842370a07f 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -940,8 +940,9 @@ static int usb_serial_probe(struct usb_interface *interface, port = serial->port[i]; if (kfifo_alloc(&port->write_fifo, PAGE_SIZE, GFP_KERNEL)) goto probe_error; - buffer_size = max_t(int, serial->type->bulk_out_size, - usb_endpoint_maxp(endpoint)); + buffer_size = serial->type->bulk_out_size; + if (!buffer_size) + buffer_size = usb_endpoint_maxp(endpoint); port->bulk_out_size = buffer_size; port->bulk_out_endpointAddress = endpoint->bEndpointAddress; diff --git a/include/linux/usb/serial.h b/include/linux/usb/serial.h index 9bb547c7bce7..704a1ab8240c 100644 --- a/include/linux/usb/serial.h +++ b/include/linux/usb/serial.h @@ -190,8 +190,7 @@ static inline void usb_set_serial_data(struct usb_serial *serial, void *data) * @num_ports: the number of different ports this device will have. * @bulk_in_size: minimum number of bytes to allocate for bulk-in buffer * (0 = end-point size) - * @bulk_out_size: minimum number of bytes to allocate for bulk-out buffer - * (0 = end-point size) + * @bulk_out_size: bytes to allocate for bulk-out buffer (0 = end-point size) * @calc_num_ports: pointer to a function to determine how many ports this * device has dynamically. It will be called after the probe() * callback is called, but before attach() -- cgit v1.2.3-59-g8ed1b From f6950344d3cf4a1e231b5828b50c4ac168db3886 Mon Sep 17 00:00:00 2001 From: Mark Glover Date: Fri, 13 Feb 2015 09:04:39 +0000 Subject: USB: ftdi_sio: add PIDs for Actisense USB devices These product identifiers (PID) all deal with marine NMEA format data used on motor boats and yachts. We supply the programmed devices to Chetco, for use inside their equipment. The PIDs are a direct copy of our Windows device drivers (FTDI drivers with altered PIDs). Signed-off-by: Mark Glover Cc: stable [johan: edit commit message slightly ] Signed-off-by: Johan Hovold --- drivers/usb/serial/ftdi_sio.c | 17 +++++++++++++++++ drivers/usb/serial/ftdi_sio_ids.h | 20 ++++++++++++++++++++ 2 files changed, 37 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 1ebb351b9e9a..651dc1ba46c3 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -978,6 +978,23 @@ static const struct usb_device_id id_table_combined[] = { { USB_DEVICE_INTERFACE_NUMBER(INFINEON_VID, INFINEON_TRIBOARD_PID, 1) }, /* GE Healthcare devices */ { USB_DEVICE(GE_HEALTHCARE_VID, GE_HEALTHCARE_NEMO_TRACKER_PID) }, + /* Active Research (Actisense) devices */ + { USB_DEVICE(FTDI_VID, ACTISENSE_NDC_PID) }, + { USB_DEVICE(FTDI_VID, ACTISENSE_USG_PID) }, + { USB_DEVICE(FTDI_VID, ACTISENSE_NGT_PID) }, + { USB_DEVICE(FTDI_VID, ACTISENSE_NGW_PID) }, + { USB_DEVICE(FTDI_VID, ACTISENSE_D9AC_PID) }, + { USB_DEVICE(FTDI_VID, ACTISENSE_D9AD_PID) }, + { USB_DEVICE(FTDI_VID, ACTISENSE_D9AE_PID) }, + { USB_DEVICE(FTDI_VID, ACTISENSE_D9AF_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEAGAUGE_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEASWITCH_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEASMART_NMEA2000_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEASMART_ETHERNET_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEASMART_WIFI_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEASMART_DISPLAY_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEASMART_LITE_PID) }, + { USB_DEVICE(FTDI_VID, CHETCO_SEASMART_ANALOG_PID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index e52409c9be99..4d3da89cd8dd 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -1438,3 +1438,23 @@ */ #define GE_HEALTHCARE_VID 0x1901 #define GE_HEALTHCARE_NEMO_TRACKER_PID 0x0015 + +/* + * Active Research (Actisense) devices + */ +#define ACTISENSE_NDC_PID 0xD9A8 /* NDC USB Serial Adapter */ +#define ACTISENSE_USG_PID 0xD9A9 /* USG USB Serial Adapter */ +#define ACTISENSE_NGT_PID 0xD9AA /* NGT NMEA2000 Interface */ +#define ACTISENSE_NGW_PID 0xD9AB /* NGW NMEA2000 Gateway */ +#define ACTISENSE_D9AC_PID 0xD9AC /* Actisense Reserved */ +#define ACTISENSE_D9AD_PID 0xD9AD /* Actisense Reserved */ +#define ACTISENSE_D9AE_PID 0xD9AE /* Actisense Reserved */ +#define ACTISENSE_D9AF_PID 0xD9AF /* Actisense Reserved */ +#define CHETCO_SEAGAUGE_PID 0xA548 /* SeaGauge USB Adapter */ +#define CHETCO_SEASWITCH_PID 0xA549 /* SeaSwitch USB Adapter */ +#define CHETCO_SEASMART_NMEA2000_PID 0xA54A /* SeaSmart NMEA2000 Gateway */ +#define CHETCO_SEASMART_ETHERNET_PID 0xA54B /* SeaSmart Ethernet Gateway */ +#define CHETCO_SEASMART_WIFI_PID 0xA5AC /* SeaSmart Wifi Gateway */ +#define CHETCO_SEASMART_DISPLAY_PID 0xA5AD /* SeaSmart NMEA2000 Display */ +#define CHETCO_SEASMART_LITE_PID 0xA5AE /* SeaSmart Lite USB Adapter */ +#define CHETCO_SEASMART_ANALOG_PID 0xA5AF /* SeaSmart Analog Adapter */ -- cgit v1.2.3-59-g8ed1b From 5ee0089b1f7057d8f783db37b2a8116cd114f6e5 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 16 Feb 2015 13:17:33 +0700 Subject: USB: console: add dummy __module_get Add call to __module_get when initialising the fake tty in usb_console_setup to match the module_put in release_one_tty. Note that the tty-driver (i.e. usb-serial core) must be compiled-in to enable the usb console so the __module_get is essentially a noop as driver->owner will be null. Reported-by: Ben Hutchings Signed-off-by: Johan Hovold --- drivers/usb/serial/console.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c index 29fa1c3d0089..3806e7014199 100644 --- a/drivers/usb/serial/console.c +++ b/drivers/usb/serial/console.c @@ -14,6 +14,7 @@ #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include +#include #include #include #include @@ -144,6 +145,7 @@ static int usb_console_setup(struct console *co, char *options) init_ldsem(&tty->ldisc_sem); INIT_LIST_HEAD(&tty->tty_files); kref_get(&tty->driver->kref); + __module_get(tty->driver->owner); tty->ops = &usb_console_fake_tty_ops; if (tty_init_termios(tty)) { retval = -ENOMEM; -- cgit v1.2.3-59-g8ed1b From 07fdfc5e9f1c966be8722e8fa927e5ea140df5ce Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 18 Feb 2015 10:34:50 +0700 Subject: USB: serial: fix potential use-after-free after failed probe Fix return value in probe error path, which could end up returning success (0) on errors. This could in turn lead to use-after-free or double free (e.g. in port_remove) when the port device is removed. Fixes: c706ebdfc895 ("USB: usb-serial: call port_probe and port_remove at the right times") Cc: stable # v2.6.31 Signed-off-by: Johan Hovold Acked-by: Greg Kroah-Hartman --- drivers/usb/serial/bus.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c index 9374bd2aba20..5d8d86666b90 100644 --- a/drivers/usb/serial/bus.c +++ b/drivers/usb/serial/bus.c @@ -75,7 +75,7 @@ static int usb_serial_device_probe(struct device *dev) retval = device_create_file(dev, &dev_attr_port_number); if (retval) { if (driver->port_remove) - retval = driver->port_remove(port); + driver->port_remove(port); goto exit_with_autopm; } -- cgit v1.2.3-59-g8ed1b From ca4383a3947a83286bc9b9c598a1f55e867871d7 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 18 Feb 2015 10:34:51 +0700 Subject: USB: serial: fix tty-device error handling at probe Add missing error handling when registering the tty device at port probe. This avoids trying to remove an uninitialised character device when the port device is removed. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Takashi Iwai Cc: stable # v2.6.12 Signed-off-by: Johan Hovold Acked-by: Greg Kroah-Hartman --- drivers/usb/serial/bus.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c index 5d8d86666b90..6f91eb9ae81a 100644 --- a/drivers/usb/serial/bus.c +++ b/drivers/usb/serial/bus.c @@ -51,6 +51,7 @@ static int usb_serial_device_probe(struct device *dev) { struct usb_serial_driver *driver; struct usb_serial_port *port; + struct device *tty_dev; int retval = 0; int minor; @@ -80,7 +81,15 @@ static int usb_serial_device_probe(struct device *dev) } minor = port->minor; - tty_register_device(usb_serial_tty_driver, minor, dev); + tty_dev = tty_register_device(usb_serial_tty_driver, minor, dev); + if (IS_ERR(tty_dev)) { + retval = PTR_ERR(tty_dev); + device_remove_file(dev, &dev_attr_port_number); + if (driver->port_remove) + driver->port_remove(port); + goto exit_with_autopm; + } + dev_info(&port->serial->dev->dev, "%s converter now attached to ttyUSB%d\n", driver->description, minor); -- cgit v1.2.3-59-g8ed1b From 2deb96b5d4bb20a33bfaf80e30f38f3433653054 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 18 Feb 2015 10:34:52 +0700 Subject: USB: serial: fix port attribute-creation race Fix attribute-creation race with userspace by using the port device groups field to create the port attributes. Also use %u when printing the port number, which is unsigned, even though we do not currently support more than 128 ports per device. Reported-by: Takashi Iwai Signed-off-by: Johan Hovold Acked-by: Greg Kroah-Hartman --- drivers/usb/serial/bus.c | 19 ------------------- drivers/usb/serial/usb-serial.c | 16 ++++++++++++++++ 2 files changed, 16 insertions(+), 19 deletions(-) diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c index 6f91eb9ae81a..b53a28692226 100644 --- a/drivers/usb/serial/bus.c +++ b/drivers/usb/serial/bus.c @@ -38,15 +38,6 @@ static int usb_serial_device_match(struct device *dev, return 0; } -static ssize_t port_number_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct usb_serial_port *port = to_usb_serial_port(dev); - - return sprintf(buf, "%d\n", port->port_number); -} -static DEVICE_ATTR_RO(port_number); - static int usb_serial_device_probe(struct device *dev) { struct usb_serial_driver *driver; @@ -73,18 +64,10 @@ static int usb_serial_device_probe(struct device *dev) goto exit_with_autopm; } - retval = device_create_file(dev, &dev_attr_port_number); - if (retval) { - if (driver->port_remove) - driver->port_remove(port); - goto exit_with_autopm; - } - minor = port->minor; tty_dev = tty_register_device(usb_serial_tty_driver, minor, dev); if (IS_ERR(tty_dev)) { retval = PTR_ERR(tty_dev); - device_remove_file(dev, &dev_attr_port_number); if (driver->port_remove) driver->port_remove(port); goto exit_with_autopm; @@ -123,8 +106,6 @@ static int usb_serial_device_remove(struct device *dev) minor = port->minor; tty_unregister_device(usb_serial_tty_driver, minor); - device_remove_file(&port->dev, &dev_attr_port_number); - driver = port->serial->type; if (driver->port_remove) retval = driver->port_remove(port); diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 19842370a07f..529066bbc7e8 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -687,6 +687,21 @@ static void serial_port_dtr_rts(struct tty_port *port, int on) drv->dtr_rts(p, on); } +static ssize_t port_number_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct usb_serial_port *port = to_usb_serial_port(dev); + + return sprintf(buf, "%u\n", port->port_number); +} +static DEVICE_ATTR_RO(port_number); + +static struct attribute *usb_serial_port_attrs[] = { + &dev_attr_port_number.attr, + NULL +}; +ATTRIBUTE_GROUPS(usb_serial_port); + static const struct tty_port_operations serial_port_ops = { .carrier_raised = serial_port_carrier_raised, .dtr_rts = serial_port_dtr_rts, @@ -902,6 +917,7 @@ static int usb_serial_probe(struct usb_interface *interface, port->dev.driver = NULL; port->dev.bus = &usb_serial_bus_type; port->dev.release = &usb_serial_port_release; + port->dev.groups = usb_serial_port_groups; device_initialize(&port->dev); } -- cgit v1.2.3-59-g8ed1b From d6f7f41274b548435ab5de1041a492fc4a714196 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 18 Feb 2015 11:04:46 +0700 Subject: USB: serial: clean up bus probe error handling Clean up bus probe error handling by separating success and error paths. Signed-off-by: Johan Hovold --- drivers/usb/serial/bus.c | 25 ++++++++++++++----------- 1 file changed, 14 insertions(+), 11 deletions(-) diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c index b53a28692226..8936a83c96cd 100644 --- a/drivers/usb/serial/bus.c +++ b/drivers/usb/serial/bus.c @@ -47,39 +47,42 @@ static int usb_serial_device_probe(struct device *dev) int minor; port = to_usb_serial_port(dev); - if (!port) { - retval = -ENODEV; - goto exit; - } + if (!port) + return -ENODEV; /* make sure suspend/resume doesn't race against port_probe */ retval = usb_autopm_get_interface(port->serial->interface); if (retval) - goto exit; + return retval; driver = port->serial->type; if (driver->port_probe) { retval = driver->port_probe(port); if (retval) - goto exit_with_autopm; + goto err_autopm_put; } minor = port->minor; tty_dev = tty_register_device(usb_serial_tty_driver, minor, dev); if (IS_ERR(tty_dev)) { retval = PTR_ERR(tty_dev); - if (driver->port_remove) - driver->port_remove(port); - goto exit_with_autopm; + goto err_port_remove; } + usb_autopm_put_interface(port->serial->interface); + dev_info(&port->serial->dev->dev, "%s converter now attached to ttyUSB%d\n", driver->description, minor); -exit_with_autopm: + return 0; + +err_port_remove: + if (driver->port_remove) + driver->port_remove(port); +err_autopm_put: usb_autopm_put_interface(port->serial->interface); -exit: + return retval; } -- cgit v1.2.3-59-g8ed1b From db81de767e375743ebb0ad2bcad3326962c2b67e Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 18 Feb 2015 11:51:07 +0700 Subject: USB: mxuport: fix null deref when used as a console Fix null-pointer dereference at probe when the device is used as a console, in which case the tty argument to open will be NULL. Fixes: ee467a1f2066 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX driver") Cc: stable # v3.14 Signed-off-by: Johan Hovold Acked-by: Greg Kroah-Hartman --- drivers/usb/serial/mxuport.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/usb/serial/mxuport.c b/drivers/usb/serial/mxuport.c index ab1d690274ae..460a40669967 100644 --- a/drivers/usb/serial/mxuport.c +++ b/drivers/usb/serial/mxuport.c @@ -1284,7 +1284,8 @@ static int mxuport_open(struct tty_struct *tty, struct usb_serial_port *port) } /* Initial port termios */ - mxuport_set_termios(tty, port, NULL); + if (tty) + mxuport_set_termios(tty, port, NULL); /* * TODO: use RQ_VENDOR_GET_MSR, once we know what it -- cgit v1.2.3-59-g8ed1b From 52772a7fd3d354ec1b88d85c83e98cbdcfb02787 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Thu, 26 Feb 2015 16:50:24 +0100 Subject: USB: pl2303: disable break on shutdown Currently an enabled break state is not disabled on final close nor on re-open and has to be disabled manually. Fix this by disabling break on port shutdown. Reported-by: Jari Ruusu Tested-by: Jari Ruusu Signed-off-by: Johan Hovold --- drivers/usb/serial/pl2303.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-) diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 0f872e6b2c87..829604d11f3f 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -132,6 +132,7 @@ MODULE_DEVICE_TABLE(usb, id_table); #define UART_OVERRUN_ERROR 0x40 #define UART_CTS 0x80 +static void pl2303_set_break(struct usb_serial_port *port, bool enable); enum pl2303_type { TYPE_01, /* Type 0 and 1 (difference unknown) */ @@ -615,6 +616,7 @@ static void pl2303_close(struct usb_serial_port *port) { usb_serial_generic_close(port); usb_kill_urb(port->interrupt_in_urb); + pl2303_set_break(port, false); } static int pl2303_open(struct tty_struct *tty, struct usb_serial_port *port) @@ -741,17 +743,16 @@ static int pl2303_ioctl(struct tty_struct *tty, return -ENOIOCTLCMD; } -static void pl2303_break_ctl(struct tty_struct *tty, int break_state) +static void pl2303_set_break(struct usb_serial_port *port, bool enable) { - struct usb_serial_port *port = tty->driver_data; struct usb_serial *serial = port->serial; u16 state; int result; - if (break_state == 0) - state = BREAK_OFF; - else + if (enable) state = BREAK_ON; + else + state = BREAK_OFF; dev_dbg(&port->dev, "%s - turning break %s\n", __func__, state == BREAK_OFF ? "off" : "on"); @@ -763,6 +764,13 @@ static void pl2303_break_ctl(struct tty_struct *tty, int break_state) dev_err(&port->dev, "error sending break = %d\n", result); } +static void pl2303_break_ctl(struct tty_struct *tty, int state) +{ + struct usb_serial_port *port = tty->driver_data; + + pl2303_set_break(port, state); +} + static void pl2303_update_line_status(struct usb_serial_port *port, unsigned char *data, unsigned int actual_length) -- cgit v1.2.3-59-g8ed1b From e1b6b6ce55a0a25c8aa8af019095253b2133a41a Mon Sep 17 00:00:00 2001 From: Nathan Lynch Date: Tue, 24 Feb 2015 17:21:07 -0600 Subject: arm64: vdso: minor ABI fix for clock_getres The vdso implementation of clock_getres currently returns 0 (success) whenever a null timespec is provided by the caller, regardless of the clock id supplied. This behavior is incorrect. It should fall back to syscall when an unrecognized clock id is passed, even when the timespec argument is null. This ensures that clock_getres always returns an error for invalid clock ids. Signed-off-by: Nathan Lynch Acked-by: Will Deacon Signed-off-by: Catalin Marinas --- arch/arm64/kernel/vdso/gettimeofday.S | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm64/kernel/vdso/gettimeofday.S b/arch/arm64/kernel/vdso/gettimeofday.S index fe652ffd34c2..efa79e8d4196 100644 --- a/arch/arm64/kernel/vdso/gettimeofday.S +++ b/arch/arm64/kernel/vdso/gettimeofday.S @@ -174,8 +174,6 @@ ENDPROC(__kernel_clock_gettime) /* int __kernel_clock_getres(clockid_t clock_id, struct timespec *res); */ ENTRY(__kernel_clock_getres) .cfi_startproc - cbz w1, 3f - cmp w0, #CLOCK_REALTIME ccmp w0, #CLOCK_MONOTONIC, #0x4, ne b.ne 1f @@ -188,6 +186,7 @@ ENTRY(__kernel_clock_getres) b.ne 4f ldr x2, 6f 2: + cbz w1, 3f stp xzr, x2, [x1] 3: /* res == NULL. */ -- cgit v1.2.3-59-g8ed1b From f5e0a12ca2d939e47995f73428d9bf1ad372b289 Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Wed, 25 Feb 2015 12:10:35 +0000 Subject: arm64: psci: move psci firmware calls out of line An arm64 allmodconfig fails to build with GCC 5 due to __asmeq assertions in the PSCI firmware calling code firing due to mcount preambles breaking our assumptions about register allocation of function arguments: /tmp/ccDqJsJ6.s: Assembler messages: /tmp/ccDqJsJ6.s:60: Error: .err encountered /tmp/ccDqJsJ6.s:61: Error: .err encountered /tmp/ccDqJsJ6.s:62: Error: .err encountered /tmp/ccDqJsJ6.s:99: Error: .err encountered /tmp/ccDqJsJ6.s:100: Error: .err encountered /tmp/ccDqJsJ6.s:101: Error: .err encountered This patch fixes the issue by moving the PSCI calls out-of-line into their own assembly files, which are safe from the compiler's meddling fingers. Reported-by: Andy Whitcroft Signed-off-by: Will Deacon Signed-off-by: Catalin Marinas --- arch/arm64/kernel/Makefile | 5 +++-- arch/arm64/kernel/psci-call.S | 28 ++++++++++++++++++++++++++++ arch/arm64/kernel/psci.c | 37 +++---------------------------------- 3 files changed, 34 insertions(+), 36 deletions(-) create mode 100644 arch/arm64/kernel/psci-call.S diff --git a/arch/arm64/kernel/Makefile b/arch/arm64/kernel/Makefile index bef04afd6031..5ee07eee80c2 100644 --- a/arch/arm64/kernel/Makefile +++ b/arch/arm64/kernel/Makefile @@ -15,8 +15,9 @@ CFLAGS_REMOVE_return_address.o = -pg arm64-obj-y := cputable.o debug-monitors.o entry.o irq.o fpsimd.o \ entry-fpsimd.o process.o ptrace.o setup.o signal.o \ sys.o stacktrace.o time.o traps.o io.o vdso.o \ - hyp-stub.o psci.o cpu_ops.o insn.o return_address.o \ - cpuinfo.o cpu_errata.o alternative.o cacheinfo.o + hyp-stub.o psci.o psci-call.o cpu_ops.o insn.o \ + return_address.o cpuinfo.o cpu_errata.o \ + alternative.o cacheinfo.o arm64-obj-$(CONFIG_COMPAT) += sys32.o kuser32.o signal32.o \ sys_compat.o entry32.o \ diff --git a/arch/arm64/kernel/psci-call.S b/arch/arm64/kernel/psci-call.S new file mode 100644 index 000000000000..cf83e61cd3b5 --- /dev/null +++ b/arch/arm64/kernel/psci-call.S @@ -0,0 +1,28 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Copyright (C) 2015 ARM Limited + * + * Author: Will Deacon + */ + +#include + +/* int __invoke_psci_fn_hvc(u64 function_id, u64 arg0, u64 arg1, u64 arg2) */ +ENTRY(__invoke_psci_fn_hvc) + hvc #0 + ret +ENDPROC(__invoke_psci_fn_hvc) + +/* int __invoke_psci_fn_smc(u64 function_id, u64 arg0, u64 arg1, u64 arg2) */ +ENTRY(__invoke_psci_fn_smc) + smc #0 + ret +ENDPROC(__invoke_psci_fn_smc) diff --git a/arch/arm64/kernel/psci.c b/arch/arm64/kernel/psci.c index 3425f311c49e..9b8a70ae64a1 100644 --- a/arch/arm64/kernel/psci.c +++ b/arch/arm64/kernel/psci.c @@ -57,6 +57,9 @@ static struct psci_operations psci_ops; static int (*invoke_psci_fn)(u64, u64, u64, u64); typedef int (*psci_initcall_t)(const struct device_node *); +asmlinkage int __invoke_psci_fn_hvc(u64, u64, u64, u64); +asmlinkage int __invoke_psci_fn_smc(u64, u64, u64, u64); + enum psci_function { PSCI_FN_CPU_SUSPEND, PSCI_FN_CPU_ON, @@ -109,40 +112,6 @@ static void psci_power_state_unpack(u32 power_state, PSCI_0_2_POWER_STATE_AFFL_SHIFT; } -/* - * The following two functions are invoked via the invoke_psci_fn pointer - * and will not be inlined, allowing us to piggyback on the AAPCS. - */ -static noinline int __invoke_psci_fn_hvc(u64 function_id, u64 arg0, u64 arg1, - u64 arg2) -{ - asm volatile( - __asmeq("%0", "x0") - __asmeq("%1", "x1") - __asmeq("%2", "x2") - __asmeq("%3", "x3") - "hvc #0\n" - : "+r" (function_id) - : "r" (arg0), "r" (arg1), "r" (arg2)); - - return function_id; -} - -static noinline int __invoke_psci_fn_smc(u64 function_id, u64 arg0, u64 arg1, - u64 arg2) -{ - asm volatile( - __asmeq("%0", "x0") - __asmeq("%1", "x1") - __asmeq("%2", "x2") - __asmeq("%3", "x3") - "smc #0\n" - : "+r" (function_id) - : "r" (arg0), "r" (arg1), "r" (arg2)); - - return function_id; -} - static int psci_get_version(void) { int err; -- cgit v1.2.3-59-g8ed1b From 06ff87bae8d30ab9c949ae8729355323e18107b4 Mon Sep 17 00:00:00 2001 From: Yingjoe Chen Date: Wed, 25 Feb 2015 10:47:45 +0800 Subject: arm64: mm: remove unused functions and variable protoypes The functions __cpu_flush_user_tlb_range and __cpu_flush_kern_tlb_range were removed in commit fa48e6f780 'arm64: mm: Optimise tlb flush logic where we have >4K granule'. Global variable cpu_tlb was never used in arm64. Remove them. Signed-off-by: Yingjoe Chen Acked-by: Will Deacon Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/tlbflush.h | 5 ----- 1 file changed, 5 deletions(-) diff --git a/arch/arm64/include/asm/tlbflush.h b/arch/arm64/include/asm/tlbflush.h index 73f0ce570fb3..4abe9b945f77 100644 --- a/arch/arm64/include/asm/tlbflush.h +++ b/arch/arm64/include/asm/tlbflush.h @@ -24,11 +24,6 @@ #include #include -extern void __cpu_flush_user_tlb_range(unsigned long, unsigned long, struct vm_area_struct *); -extern void __cpu_flush_kern_tlb_range(unsigned long, unsigned long); - -extern struct cpu_tlb_fns cpu_tlb; - /* * TLB Management * ============== -- cgit v1.2.3-59-g8ed1b From 6910fa16dbe142f6a0fd0fd7c249f9883ff7fc8a Mon Sep 17 00:00:00 2001 From: Feng Kan Date: Tue, 24 Feb 2015 15:40:21 -0800 Subject: arm64: enable PTE type bit in the mask for pte_modify Caught during Trinity testing. The pte_modify does not allow modification for PTE type bit. This cause the test to hang the system. It is found that the PTE can't transit from an inaccessible page (b00) to a valid page (b11) because the mask does not allow it. This happens when a big block of mmaped memory is set the PROT_NONE, then the a small piece is broken off and set to PROT_WRITE | PROT_READ cause a huge page split. Signed-off-by: Feng Kan Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/pgtable.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/include/asm/pgtable.h b/arch/arm64/include/asm/pgtable.h index 16449c535e50..800ec0e87ed9 100644 --- a/arch/arm64/include/asm/pgtable.h +++ b/arch/arm64/include/asm/pgtable.h @@ -460,7 +460,7 @@ static inline pud_t *pud_offset(pgd_t *pgd, unsigned long addr) static inline pte_t pte_modify(pte_t pte, pgprot_t newprot) { const pteval_t mask = PTE_USER | PTE_PXN | PTE_UXN | PTE_RDONLY | - PTE_PROT_NONE | PTE_VALID | PTE_WRITE; + PTE_PROT_NONE | PTE_WRITE | PTE_TYPE_MASK; pte_val(pte) = (pte_val(pte) & ~mask) | (pgprot_val(newprot) & mask); return pte; } -- cgit v1.2.3-59-g8ed1b From 0eee0fbd41c7b57d01136df2519c92ec1506e333 Mon Sep 17 00:00:00 2001 From: Ard Biesheuvel Date: Thu, 19 Feb 2015 17:25:16 +0000 Subject: arm64: crypto: increase AES interleave to 4x This patch increases the interleave factor for parallel AES modes to 4x. This improves performance on Cortex-A57 by ~35%. This is due to the 3-cycle latency of AES instructions on the A57's relatively deep pipeline (compared to Cortex-A53 where the AES instruction latency is only 2 cycles). At the same time, disable inline expansion of the core AES functions, as the performance benefit of this feature is negligible. Measured on AMD Seattle (using tcrypt.ko mode=500 sec=1): Baseline (2x interleave, inline expansion) ------------------------------------------ testing speed of async cbc(aes) (cbc-aes-ce) decryption test 4 (128 bit key, 8192 byte blocks): 95545 operations in 1 seconds test 14 (256 bit key, 8192 byte blocks): 68496 operations in 1 seconds This patch (4x interleave, no inline expansion) ----------------------------------------------- testing speed of async cbc(aes) (cbc-aes-ce) decryption test 4 (128 bit key, 8192 byte blocks): 124735 operations in 1 seconds test 14 (256 bit key, 8192 byte blocks): 92328 operations in 1 seconds Signed-off-by: Ard Biesheuvel Signed-off-by: Catalin Marinas --- arch/arm64/crypto/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/crypto/Makefile b/arch/arm64/crypto/Makefile index 5720608c50b1..abb79b3cfcfe 100644 --- a/arch/arm64/crypto/Makefile +++ b/arch/arm64/crypto/Makefile @@ -29,7 +29,7 @@ aes-ce-blk-y := aes-glue-ce.o aes-ce.o obj-$(CONFIG_CRYPTO_AES_ARM64_NEON_BLK) += aes-neon-blk.o aes-neon-blk-y := aes-glue-neon.o aes-neon.o -AFLAGS_aes-ce.o := -DINTERLEAVE=2 -DINTERLEAVE_INLINE +AFLAGS_aes-ce.o := -DINTERLEAVE=4 AFLAGS_aes-neon.o := -DINTERLEAVE=4 CFLAGS_aes-glue-ce.o := -DUSE_V8_CRYPTO_EXTENSIONS -- cgit v1.2.3-59-g8ed1b From f6242cac10427c546271050b31c891a078e490cd Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Tue, 24 Feb 2015 16:30:21 +0000 Subject: arm64: Fix text patching logic when using fixmap Patch 2f896d586610 ("arm64: use fixmap for text patching") changed the way we patch the kernel text, using a fixmap when the kernel or modules are flagged as read only. Unfortunately, a flaw in the logic makes it fall over when patching modules without CONFIG_DEBUG_SET_MODULE_RONX enabled: [...] [ 32.032636] Call trace: [ 32.032716] [] __copy_to_user+0x2c/0x60 [ 32.032837] [] __aarch64_insn_write+0x94/0xf8 [ 32.033027] [] aarch64_insn_patch_text_nosync+0x18/0x58 [ 32.033200] [] ftrace_modify_code+0x58/0x84 [ 32.033363] [] ftrace_make_nop+0x3c/0x58 [ 32.033532] [] ftrace_process_locs+0x3d0/0x5c8 [ 32.033709] [] ftrace_module_init+0x28/0x34 [ 32.033882] [] load_module+0xbb8/0xfc4 [ 32.034044] [] SyS_finit_module+0x94/0xc4 [...] This is triggered by the use of virt_to_page() on a module address, which ends to pointing to Nowhereland if you're lucky, or corrupt your precious data if not. This patch fixes the logic by mimicking what is done on arm: - If we're patching a module and CONFIG_DEBUG_SET_MODULE_RONX is set, use vmalloc_to_page(). - If we're patching the kernel and CONFIG_DEBUG_RODATA is set, use virt_to_page(). - Otherwise, use the provided address, as we can write to it directly. Tested on 4.0-rc1 as a KVM guest. Reported-by: Richard W.M. Jones Reviewed-by: Kees Cook Acked-by: Mark Rutland Acked-by: Laura Abbott Tested-by: Richard W.M. Jones Cc: Will Deacon Signed-off-by: Marc Zyngier Signed-off-by: Catalin Marinas --- arch/arm64/kernel/insn.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/arm64/kernel/insn.c b/arch/arm64/kernel/insn.c index 27d4864577e5..c8eca88f12e6 100644 --- a/arch/arm64/kernel/insn.c +++ b/arch/arm64/kernel/insn.c @@ -87,8 +87,10 @@ static void __kprobes *patch_map(void *addr, int fixmap) if (module && IS_ENABLED(CONFIG_DEBUG_SET_MODULE_RONX)) page = vmalloc_to_page(addr); - else + else if (!module && IS_ENABLED(CONFIG_DEBUG_RODATA)) page = virt_to_page(addr); + else + return addr; BUG_ON(!page); set_fixmap(fixmap, page_to_phys(page)); -- cgit v1.2.3-59-g8ed1b From 9c1c98a3bb7b7593b60264b9a07e001e68b46697 Mon Sep 17 00:00:00 2001 From: Jouni Malinen Date: Thu, 26 Feb 2015 15:50:50 +0200 Subject: mac80211: Send EAPOL frames at lowest rate The current minstrel_ht rate control behavior is somewhat optimistic in trying to find optimum TX rate. While this is usually fine for normal Data frames, there are cases where a more conservative set of retry parameters would be beneficial to make the connection more robust. EAPOL frames are critical to the authentication and especially the EAPOL-Key message 4/4 (the last message in the 4-way handshake) is important to get through to the AP. If that message is lost, the only recovery mechanism in many cases is to reassociate with the AP and start from scratch. This can often be avoided by trying to send the frame with more conservative rate and/or with more link layer retries. In most cases, minstrel_ht is currently using the initial EAPOL-Key frames for probing higher rates and this results in only five link layer transmission attempts (one at high(ish) MCS and four at MCS0). While this works with most APs, it looks like there are some deployed APs that may have issues with the EAPOL frames using HT MCS immediately after association. Similarly, there may be issues in cases where the signal strength or radio environment is not good enough to be able to get frames through even at couple of MCS 0 tries. The best approach for this would likely to be to reduce the TX rate for the last rate (3rd rate parameter in the set) to a low basic rate (say, 6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly requires some more effort. For now, we can start with a simple one-liner that forces the minimum rate to be used for EAPOL frames similarly how the TX rate is selected for the IEEE 802.11 Management frames. This does result in a small extra latency added to the cases where the AP would be able to receive the higher rate, but taken into account how small number of EAPOL frames are used, this is likely to be insignificant. A future optimization in the minstrel_ht design can also allow this patch to be reverted to get back to the more optimized initial TX rate. It should also be noted that many drivers that do not use minstrel as the rate control algorithm are already doing similar workarounds by forcing the lowest TX rate to be used for EAPOL frames. Cc: stable@vger.kernel.org Reported-by: Linus Torvalds Tested-by: Linus Torvalds Signed-off-by: Jouni Malinen Signed-off-by: Johannes Berg --- net/mac80211/tx.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c index 88a18ffe2975..07bd8db00af8 100644 --- a/net/mac80211/tx.c +++ b/net/mac80211/tx.c @@ -566,6 +566,7 @@ ieee80211_tx_h_check_control_port_protocol(struct ieee80211_tx_data *tx) if (tx->sdata->control_port_no_encrypt) info->flags |= IEEE80211_TX_INTFL_DONT_ENCRYPT; info->control.flags |= IEEE80211_TX_CTRL_PORT_CTRL_PROTO; + info->flags |= IEEE80211_TX_CTL_USE_MINRATE; } return TX_CONTINUE; -- cgit v1.2.3-59-g8ed1b From c876486be17aeefe0da569f3d111cbd8de6f675d Mon Sep 17 00:00:00 2001 From: Andrew Elble Date: Wed, 25 Feb 2015 17:46:27 -0500 Subject: nfsd: fix clp->cl_revoked list deletion causing softlock in nfsd commit 2d4a532d385f ("nfsd: ensure that clp->cl_revoked list is protected by clp->cl_lock") removed the use of the reaplist to clean out clp->cl_revoked. It failed to change list_entry() to walk clp->cl_revoked.next instead of reaplist.next Fixes: 2d4a532d385f ("nfsd: ensure that clp->cl_revoked list is protected by clp->cl_lock") Cc: stable@vger.kernel.org Reported-by: Eric Meddaugh Tested-by: Eric Meddaugh Signed-off-by: Andrew Elble Reviewed-by: Jeff Layton Signed-off-by: J. Bruce Fields --- fs/nfsd/nfs4state.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/nfsd/nfs4state.c b/fs/nfsd/nfs4state.c index f6b2a09f793f..d2f2c37dc2db 100644 --- a/fs/nfsd/nfs4state.c +++ b/fs/nfsd/nfs4state.c @@ -1638,7 +1638,7 @@ __destroy_client(struct nfs4_client *clp) nfs4_put_stid(&dp->dl_stid); } while (!list_empty(&clp->cl_revoked)) { - dp = list_entry(reaplist.next, struct nfs4_delegation, dl_recall_lru); + dp = list_entry(clp->cl_revoked.next, struct nfs4_delegation, dl_recall_lru); list_del_init(&dp->dl_recall_lru); nfs4_put_stid(&dp->dl_stid); } -- cgit v1.2.3-59-g8ed1b From 76cb4be993c03bf9ec65a58b13f12c679bb041e4 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Tue, 24 Feb 2015 18:34:01 +0300 Subject: sunrpc: integer underflow in rsc_parse() If we call groups_alloc() with invalid values then it's might lead to memory corruption. For example, with a negative value then we might not allocate enough for sizeof(struct group_info). (We're doing this in the caller for consistency with other callers of groups_alloc(). The other alternative might be to move the check out of all the callers into groups_alloc().) Signed-off-by: Dan Carpenter Reviewed-by: Simo Sorce Signed-off-by: J. Bruce Fields --- net/sunrpc/auth_gss/svcauth_gss.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/sunrpc/auth_gss/svcauth_gss.c b/net/sunrpc/auth_gss/svcauth_gss.c index 224a82f24d3c..1095be9c80ab 100644 --- a/net/sunrpc/auth_gss/svcauth_gss.c +++ b/net/sunrpc/auth_gss/svcauth_gss.c @@ -463,6 +463,8 @@ static int rsc_parse(struct cache_detail *cd, /* number of additional gid's */ if (get_int(&mesg, &N)) goto out; + if (N < 0 || N > NGROUPS_MAX) + goto out; status = -ENOMEM; rsci.cred.cr_group_info = groups_alloc(N); if (rsci.cred.cr_group_info == NULL) -- cgit v1.2.3-59-g8ed1b From 3a51d50f426cbb65add424baebe511dcf5ac45cc Mon Sep 17 00:00:00 2001 From: Vineet Gupta Date: Wed, 10 Jul 2013 16:03:45 +0200 Subject: ARC: Make arc_unwind_core accessible externally The arc unwinder can also be used for perf callchains. Signed-off-by: Mischa Jonker Signed-off-by: Vineet Gupta --- arch/arc/include/asm/stacktrace.h | 37 +++++++++++++++++++++++++++++++++++++ arch/arc/kernel/stacktrace.c | 15 ++++++++++++++- 2 files changed, 51 insertions(+), 1 deletion(-) create mode 100644 arch/arc/include/asm/stacktrace.h diff --git a/arch/arc/include/asm/stacktrace.h b/arch/arc/include/asm/stacktrace.h new file mode 100644 index 000000000000..b29b6064ea14 --- /dev/null +++ b/arch/arc/include/asm/stacktrace.h @@ -0,0 +1,37 @@ +/* + * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com) + * Copyright (C) 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_STACKTRACE_H +#define __ASM_STACKTRACE_H + +#include + +/** + * arc_unwind_core - Unwind the kernel mode stack for an execution context + * @tsk: NULL for current task, specific task otherwise + * @regs: pt_regs used to seed the unwinder {SP, FP, BLINK, PC} + * If NULL, use pt_regs of @tsk (if !NULL) otherwise + * use the current values of {SP, FP, BLINK, PC} + * @consumer_fn: Callback invoked for each frame unwound + * Returns 0 to continue unwinding, -1 to stop + * @arg: Arg to callback + * + * Returns the address of first function in stack + * + * Semantics: + * - synchronous unwinding (e.g. dump_stack): @tsk NULL, @regs NULL + * - Asynchronous unwinding of sleeping task: @tsk !NULL, @regs NULL + * - Asynchronous unwinding of intr/excp etc: @tsk !NULL, @regs !NULL + */ +notrace noinline unsigned int arc_unwind_core( + struct task_struct *tsk, struct pt_regs *regs, + int (*consumer_fn) (unsigned int, void *), + void *arg); + +#endif /* __ASM_STACKTRACE_H */ diff --git a/arch/arc/kernel/stacktrace.c b/arch/arc/kernel/stacktrace.c index 9ce47cfe2303..6492507a3d74 100644 --- a/arch/arc/kernel/stacktrace.c +++ b/arch/arc/kernel/stacktrace.c @@ -43,6 +43,10 @@ static void seed_unwind_frame_info(struct task_struct *tsk, struct pt_regs *regs, struct unwind_frame_info *frame_info) { + /* + * synchronous unwinding (e.g. dump_stack) + * - uses current values of SP and friends + */ if (tsk == NULL && regs == NULL) { unsigned long fp, sp, blink, ret; frame_info->task = current; @@ -61,6 +65,11 @@ static void seed_unwind_frame_info(struct task_struct *tsk, frame_info->regs.r63 = ret; frame_info->call_frame = 0; } else if (regs == NULL) { + /* + * Asynchronous unwinding of sleeping task + * - Gets SP etc from task's pt_regs (saved bottom of kernel + * mode stack of task) + */ frame_info->task = tsk; @@ -83,6 +92,10 @@ static void seed_unwind_frame_info(struct task_struct *tsk, frame_info->call_frame = 0; } else { + /* + * Asynchronous unwinding of intr/exception + * - Just uses the pt_regs passed + */ frame_info->task = tsk; frame_info->regs.r27 = regs->fp; @@ -95,7 +108,7 @@ static void seed_unwind_frame_info(struct task_struct *tsk, #endif -static noinline unsigned int +notrace noinline unsigned int arc_unwind_core(struct task_struct *tsk, struct pt_regs *regs, int (*consumer_fn) (unsigned int, void *), void *arg) { -- cgit v1.2.3-59-g8ed1b From ceed97ab4ff76cb5b1d616a810e941f8837dc440 Mon Sep 17 00:00:00 2001 From: Vineet Gupta Date: Thu, 2 Oct 2014 12:30:42 +0530 Subject: ARC: perf: Enable generic software events Signed-off-by: Vineet Gupta --- arch/arc/kernel/unaligned.c | 2 ++ arch/arc/mm/fault.c | 12 ++++++++++-- 2 files changed, 12 insertions(+), 2 deletions(-) diff --git a/arch/arc/kernel/unaligned.c b/arch/arc/kernel/unaligned.c index 7ff5b5c183bb..74db59b6f392 100644 --- a/arch/arc/kernel/unaligned.c +++ b/arch/arc/kernel/unaligned.c @@ -12,6 +12,7 @@ */ #include +#include #include #include #include @@ -253,6 +254,7 @@ int misaligned_fixup(unsigned long address, struct pt_regs *regs, } } + perf_sw_event(PERF_COUNT_SW_ALIGNMENT_FAULTS, 1, regs, address); return 0; fault: diff --git a/arch/arc/mm/fault.c b/arch/arc/mm/fault.c index 563cb27e37f5..6a2e006cbcce 100644 --- a/arch/arc/mm/fault.c +++ b/arch/arc/mm/fault.c @@ -14,6 +14,7 @@ #include #include #include +#include #include #include @@ -139,13 +140,20 @@ good_area: return; } + perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address); + if (likely(!(fault & VM_FAULT_ERROR))) { if (flags & FAULT_FLAG_ALLOW_RETRY) { /* To avoid updating stats twice for retry case */ - if (fault & VM_FAULT_MAJOR) + if (fault & VM_FAULT_MAJOR) { tsk->maj_flt++; - else + perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS_MAJ, 1, + regs, address); + } else { tsk->min_flt++; + perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS_MIN, 1, + regs, address); + } if (fault & VM_FAULT_RETRY) { flags &= ~FAULT_FLAG_ALLOW_RETRY; -- cgit v1.2.3-59-g8ed1b From 13648b0118a24f4fc76c34e6c7b6ccf447e46a2a Mon Sep 17 00:00:00 2001 From: Vineet Gupta Date: Fri, 27 Feb 2015 10:39:17 +0530 Subject: ARC: Fix KSTK_ESP() /proc//maps currently don't annotate stack vma with "[stack]" This is because KSTK_ESP ie expected to return usermode SP of tsk while currently it returns the kernel mode SP of a sleeping tsk. While the fix is trivial, we also need to adjust the ARC kernel stack unwinder to not use KSTK_SP and friends any more. Cc: Reported-and-suggested-by: Alexey Brodkin Signed-off-by: Vineet Gupta --- arch/arc/include/asm/processor.h | 9 +++++---- arch/arc/kernel/stacktrace.c | 6 +++--- 2 files changed, 8 insertions(+), 7 deletions(-) diff --git a/arch/arc/include/asm/processor.h b/arch/arc/include/asm/processor.h index 4e547296831d..88398caa3989 100644 --- a/arch/arc/include/asm/processor.h +++ b/arch/arc/include/asm/processor.h @@ -72,18 +72,19 @@ unsigned long thread_saved_pc(struct task_struct *t); #define release_segments(mm) do { } while (0) #define KSTK_EIP(tsk) (task_pt_regs(tsk)->ret) +#define KSTK_ESP(tsk) (task_pt_regs(tsk)->sp) /* * Where abouts of Task's sp, fp, blink when it was last seen in kernel mode. * Look in process.c for details of kernel stack layout */ -#define KSTK_ESP(tsk) (tsk->thread.ksp) +#define TSK_K_ESP(tsk) (tsk->thread.ksp) -#define KSTK_REG(tsk, off) (*((unsigned int *)(KSTK_ESP(tsk) + \ +#define TSK_K_REG(tsk, off) (*((unsigned int *)(TSK_K_ESP(tsk) + \ sizeof(struct callee_regs) + off))) -#define KSTK_BLINK(tsk) KSTK_REG(tsk, 4) -#define KSTK_FP(tsk) KSTK_REG(tsk, 0) +#define TSK_K_BLINK(tsk) TSK_K_REG(tsk, 4) +#define TSK_K_FP(tsk) TSK_K_REG(tsk, 0) extern void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long usp); diff --git a/arch/arc/kernel/stacktrace.c b/arch/arc/kernel/stacktrace.c index 6492507a3d74..92320d6f737c 100644 --- a/arch/arc/kernel/stacktrace.c +++ b/arch/arc/kernel/stacktrace.c @@ -73,9 +73,9 @@ static void seed_unwind_frame_info(struct task_struct *tsk, frame_info->task = tsk; - frame_info->regs.r27 = KSTK_FP(tsk); - frame_info->regs.r28 = KSTK_ESP(tsk); - frame_info->regs.r31 = KSTK_BLINK(tsk); + frame_info->regs.r27 = TSK_K_FP(tsk); + frame_info->regs.r28 = TSK_K_ESP(tsk); + frame_info->regs.r31 = TSK_K_BLINK(tsk); frame_info->regs.r63 = (unsigned int)__switch_to; /* In the prologue of __switch_to, first FP is saved on stack -- cgit v1.2.3-59-g8ed1b From 3240dd57e533da94998029af6e17008a1806c665 Mon Sep 17 00:00:00 2001 From: Vineet Gupta Date: Fri, 27 Feb 2015 10:59:31 +0530 Subject: ARC: Fix thread_saved_pc() The old implementation assumed that SP at the time of __switch_to() is right above pt_regs which is almost certainly not the case as there will be some stack build up between entry into kernel and leading up to __switch_to Signed-off-by: Vineet Gupta --- arch/arc/include/asm/processor.h | 5 ++--- arch/arc/kernel/process.c | 23 ----------------------- 2 files changed, 2 insertions(+), 26 deletions(-) diff --git a/arch/arc/include/asm/processor.h b/arch/arc/include/asm/processor.h index 88398caa3989..52312cb5dbe2 100644 --- a/arch/arc/include/asm/processor.h +++ b/arch/arc/include/asm/processor.h @@ -47,9 +47,6 @@ struct thread_struct { /* Forward declaration, a strange C thing */ struct task_struct; -/* Return saved PC of a blocked thread */ -unsigned long thread_saved_pc(struct task_struct *t); - #define task_pt_regs(p) \ ((struct pt_regs *)(THREAD_SIZE + (void *)task_stack_page(p)) - 1) @@ -86,6 +83,8 @@ unsigned long thread_saved_pc(struct task_struct *t); #define TSK_K_BLINK(tsk) TSK_K_REG(tsk, 4) #define TSK_K_FP(tsk) TSK_K_REG(tsk, 0) +#define thread_saved_pc(tsk) TSK_K_BLINK(tsk) + extern void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long usp); diff --git a/arch/arc/kernel/process.c b/arch/arc/kernel/process.c index fdd89715d2d3..98c00a2d4dd9 100644 --- a/arch/arc/kernel/process.c +++ b/arch/arc/kernel/process.c @@ -192,29 +192,6 @@ int dump_fpu(struct pt_regs *regs, elf_fpregset_t *fpu) return 0; } -/* - * API: expected by schedular Code: If thread is sleeping where is that. - * What is this good for? it will be always the scheduler or ret_from_fork. - * So we hard code that anyways. - */ -unsigned long thread_saved_pc(struct task_struct *t) -{ - struct pt_regs *regs = task_pt_regs(t); - unsigned long blink = 0; - - /* - * If the thread being queried for in not itself calling this, then it - * implies it is not executing, which in turn implies it is sleeping, - * which in turn implies it got switched OUT by the schedular. - * In that case, it's kernel mode blink can reliably retrieved as per - * the picture above (right above pt_regs). - */ - if (t != current && t->state != TASK_RUNNING) - blink = *((unsigned int *)regs - 1); - - return blink; -} - int elf_check_arch(const struct elf32_hdr *x) { unsigned int eflags; -- cgit v1.2.3-59-g8ed1b From 675af70856d7cc026be8b6ea7a8b9db10b8b38a1 Mon Sep 17 00:00:00 2001 From: Michiel vd Garde Date: Fri, 27 Feb 2015 02:08:29 +0100 Subject: USB: serial: cp210x: Adding Seletek device id's These device ID's are not associated with the cp210x module currently, but should be. This patch allows the devices to operate upon connecting them to the usb bus as intended. Signed-off-by: Michiel van de Garde Cc: stable Signed-off-by: Johan Hovold --- drivers/usb/serial/cp210x.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index f40c856ff758..84ce2d74894c 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -147,6 +147,8 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x166A, 0x0305) }, /* Clipsal C-5000CT2 C-Bus Spectrum Colour Touchscreen */ { USB_DEVICE(0x166A, 0x0401) }, /* Clipsal L51xx C-Bus Architectural Dimmer */ { USB_DEVICE(0x166A, 0x0101) }, /* Clipsal 5560884 C-Bus Multi-room Audio Matrix Switcher */ + { USB_DEVICE(0x16C0, 0x09B0) }, /* Lunatico Seletek */ + { USB_DEVICE(0x16C0, 0x09B1) }, /* Lunatico Seletek */ { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */ { USB_DEVICE(0x16DC, 0x0010) }, /* W-IE-NE-R Plein & Baus GmbH PL512 Power Supply */ { USB_DEVICE(0x16DC, 0x0011) }, /* W-IE-NE-R Plein & Baus GmbH RCM Remote Control for MARATON Power Supply */ -- cgit v1.2.3-59-g8ed1b From f2b14c0bc510c6a8f67a4f36049deefe5d99a537 Mon Sep 17 00:00:00 2001 From: Takashi Sakamoto Date: Fri, 27 Feb 2015 09:39:32 +0900 Subject: ALSA: oxfw: fix a condition and return code in start_stream() The amdtp_stream_wait_callback() doesn't return minus value and the return code is not for error code. This commit fixes with a propper condition and an error code. Fixes: f3699e2c7745 ('ALSA: oxfw: Change the way to start stream') Reported-by: Dan Carpenter Signed-off-by: Takashi Sakamoto Cc: # 3.19+ Signed-off-by: Takashi Iwai --- sound/firewire/oxfw/oxfw-stream.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/sound/firewire/oxfw/oxfw-stream.c b/sound/firewire/oxfw/oxfw-stream.c index 29ccb3637164..e6757cd85724 100644 --- a/sound/firewire/oxfw/oxfw-stream.c +++ b/sound/firewire/oxfw/oxfw-stream.c @@ -171,9 +171,10 @@ static int start_stream(struct snd_oxfw *oxfw, struct amdtp_stream *stream, } /* Wait first packet */ - err = amdtp_stream_wait_callback(stream, CALLBACK_TIMEOUT); - if (err < 0) + if (!amdtp_stream_wait_callback(stream, CALLBACK_TIMEOUT)) { stop_stream(oxfw, stream); + err = -ETIMEDOUT; + } end: return err; } -- cgit v1.2.3-59-g8ed1b From a1e50a82256ed2f1312e70c52a84323e2e378f49 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Thu, 5 Feb 2015 18:01:53 +0000 Subject: arm64: Increase the swiotlb buffer size 64MB With commit 3690951fc6d4 (arm64: Use swiotlb late initialisation), the swiotlb buffer size is limited to MAX_ORDER_NR_PAGES. However, there are platforms with 32-bit only devices that require bounce buffering via swiotlb. This patch changes the swiotlb initialisation to an early 64MB memblock allocation. In order to get the swiotlb buffer correctly allocated (via memblock_virt_alloc_low_nopanic), this patch also defines ARCH_LOW_ADDRESS_LIMIT to the maximum physical address capable of 32-bit DMA. Reported-by: Kefeng Wang Tested-by: Kefeng Wang Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/processor.h | 3 ++- arch/arm64/mm/dma-mapping.c | 16 +++------------- arch/arm64/mm/init.c | 14 +++++++++----- 3 files changed, 14 insertions(+), 19 deletions(-) diff --git a/arch/arm64/include/asm/processor.h b/arch/arm64/include/asm/processor.h index f9be30ea1cbd..20e9591a60cf 100644 --- a/arch/arm64/include/asm/processor.h +++ b/arch/arm64/include/asm/processor.h @@ -45,7 +45,8 @@ #define STACK_TOP STACK_TOP_MAX #endif /* CONFIG_COMPAT */ -#define ARCH_LOW_ADDRESS_LIMIT PHYS_MASK +extern phys_addr_t arm64_dma_phys_limit; +#define ARCH_LOW_ADDRESS_LIMIT (arm64_dma_phys_limit - 1) #endif /* __KERNEL__ */ struct debug_info { diff --git a/arch/arm64/mm/dma-mapping.c b/arch/arm64/mm/dma-mapping.c index 0a24b9b8c698..58e0c2bdde04 100644 --- a/arch/arm64/mm/dma-mapping.c +++ b/arch/arm64/mm/dma-mapping.c @@ -348,8 +348,6 @@ static struct dma_map_ops swiotlb_dma_ops = { .mapping_error = swiotlb_dma_mapping_error, }; -extern int swiotlb_late_init_with_default_size(size_t default_size); - static int __init atomic_pool_init(void) { pgprot_t prot = __pgprot(PROT_NORMAL_NC); @@ -411,21 +409,13 @@ out: return -ENOMEM; } -static int __init swiotlb_late_init(void) +static int __init arm64_dma_init(void) { - size_t swiotlb_size = min(SZ_64M, MAX_ORDER_NR_PAGES << PAGE_SHIFT); + int ret; dma_ops = &swiotlb_dma_ops; - return swiotlb_late_init_with_default_size(swiotlb_size); -} - -static int __init arm64_dma_init(void) -{ - int ret = 0; - - ret |= swiotlb_late_init(); - ret |= atomic_pool_init(); + ret = atomic_pool_init(); return ret; } diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c index 71145f952070..ae85da6307bb 100644 --- a/arch/arm64/mm/init.c +++ b/arch/arm64/mm/init.c @@ -33,6 +33,7 @@ #include #include #include +#include #include #include @@ -45,6 +46,7 @@ #include "mm.h" phys_addr_t memstart_addr __read_mostly = 0; +phys_addr_t arm64_dma_phys_limit __read_mostly; #ifdef CONFIG_BLK_DEV_INITRD static int __init early_initrd(char *p) @@ -85,7 +87,7 @@ static void __init zone_sizes_init(unsigned long min, unsigned long max) /* 4GB maximum for 32-bit only capable devices */ if (IS_ENABLED(CONFIG_ZONE_DMA)) { - max_dma = PFN_DOWN(max_zone_dma_phys()); + max_dma = PFN_DOWN(arm64_dma_phys_limit); zone_size[ZONE_DMA] = max_dma - min; } zone_size[ZONE_NORMAL] = max - max_dma; @@ -156,8 +158,6 @@ early_param("mem", early_mem); void __init arm64_memblock_init(void) { - phys_addr_t dma_phys_limit = 0; - memblock_enforce_memory_limit(memory_limit); /* @@ -174,8 +174,10 @@ void __init arm64_memblock_init(void) /* 4GB maximum for 32-bit only capable devices */ if (IS_ENABLED(CONFIG_ZONE_DMA)) - dma_phys_limit = max_zone_dma_phys(); - dma_contiguous_reserve(dma_phys_limit); + arm64_dma_phys_limit = max_zone_dma_phys(); + else + arm64_dma_phys_limit = PHYS_MASK + 1; + dma_contiguous_reserve(arm64_dma_phys_limit); memblock_allow_resize(); memblock_dump_all(); @@ -276,6 +278,8 @@ static void __init free_unused_memmap(void) */ void __init mem_init(void) { + swiotlb_init(1); + set_max_mapnr(pfn_to_page(max_pfn) - mem_map); #ifndef CONFIG_SPARSEMEM_VMEMMAP -- cgit v1.2.3-59-g8ed1b From 9d42d48a342aee208c1154696196497fdc556bbf Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Mon, 23 Feb 2015 15:13:40 +0000 Subject: arm64: compat Fix siginfo_t -> compat_siginfo_t conversion on big endian The native (64-bit) sigval_t union contains sival_int (32-bit) and sival_ptr (64-bit). When a compat application invokes a syscall that takes a sigval_t value (as part of a larger structure, e.g. compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t union is converted to the native sigval_t with sival_int overlapping with either the least or the most significant half of sival_ptr, depending on endianness. When the corresponding signal is delivered to a compat application, on big endian the current (compat_uptr_t)sival_ptr cast always returns 0 since sival_int corresponds to the top part of sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int is copied to the compat_siginfo_t structure. Cc: Reported-by: Bamvor Jian Zhang Tested-by: Bamvor Jian Zhang Signed-off-by: Catalin Marinas --- arch/arm64/kernel/signal32.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/arch/arm64/kernel/signal32.c b/arch/arm64/kernel/signal32.c index c20a300e2213..d26fcd4cd6e6 100644 --- a/arch/arm64/kernel/signal32.c +++ b/arch/arm64/kernel/signal32.c @@ -154,8 +154,7 @@ int copy_siginfo_to_user32(compat_siginfo_t __user *to, const siginfo_t *from) case __SI_TIMER: err |= __put_user(from->si_tid, &to->si_tid); err |= __put_user(from->si_overrun, &to->si_overrun); - err |= __put_user((compat_uptr_t)(unsigned long)from->si_ptr, - &to->si_ptr); + err |= __put_user(from->si_int, &to->si_int); break; case __SI_POLL: err |= __put_user(from->si_band, &to->si_band); @@ -184,7 +183,7 @@ int copy_siginfo_to_user32(compat_siginfo_t __user *to, const siginfo_t *from) case __SI_MESGQ: /* But this is */ err |= __put_user(from->si_pid, &to->si_pid); err |= __put_user(from->si_uid, &to->si_uid); - err |= __put_user((compat_uptr_t)(unsigned long)from->si_ptr, &to->si_ptr); + err |= __put_user(from->si_int, &to->si_int); break; case __SI_SYS: err |= __put_user((compat_uptr_t)(unsigned long) -- cgit v1.2.3-59-g8ed1b From af4819af8db05da4753b3b74a11cb00b381247e7 Mon Sep 17 00:00:00 2001 From: Lorenzo Pieralisi Date: Fri, 27 Feb 2015 17:54:31 +0000 Subject: arm64: cpuidle: add asm/proc-fns.h inclusion ARM64 CPUidle driver requires the cpu_do_idle function so that it can be used to enter the shallowest idle state, and it is declared in asm/proc-fns.h. The current ARM64 CPUidle driver does not include asm/proc-fns.h explicitly and it has so far relied on implicit inclusion from other header files. Owing to some header dependencies reshuffling this currently triggers build failures when CONFIG_ARM64_64K_PAGES=y: drivers/cpuidle/cpuidle-arm64.c: In function "arm64_enter_idle_state" drivers/cpuidle/cpuidle-arm64.c:42:3: error: implicit declaration of function "cpu_do_idle" [-Werror=implicit-function-declaration] cpu_do_idle(); ^ This patch adds the explicit inclusion of the asm/proc-fns.h header file in the arm64 asm/cpuidle.h header file, so that the build breakage is fixed and the required header inclusion is added to the appropriate arch back-end CPUidle header, already included by the CPUidle arm64 driver, where CPUidle arch related function declarations belong. Reported-by: Laura Abbott Signed-off-by: Lorenzo Pieralisi Acked-by: Will Deacon Tested-by: Mark Rutland Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/cpuidle.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/include/asm/cpuidle.h b/arch/arm64/include/asm/cpuidle.h index 0710654631e7..c60643f14cda 100644 --- a/arch/arm64/include/asm/cpuidle.h +++ b/arch/arm64/include/asm/cpuidle.h @@ -1,6 +1,8 @@ #ifndef __ASM_CPUIDLE_H #define __ASM_CPUIDLE_H +#include + #ifdef CONFIG_CPU_IDLE extern int cpu_init_idle(unsigned int cpu); extern int cpu_suspend(unsigned long arg); -- cgit v1.2.3-59-g8ed1b From ddbd2b7ad99a418c60397901a0f3c997d030c65e Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Fri, 27 Feb 2015 11:44:24 -0800 Subject: Code of Conflict This file provides a basic guide for how to handle conflict resolution when it comes up in the development process. Acked-by: Alex Deucher Acked-by: Arjan van de Ven Acked-by: Arnaldo Carvalho de Melo Acked-by: Arnd Bergmann Acked-by: Benjamin Herrenschmidt Acked-by: Chris Ball Acked-by: Chris Mason Acked-by: Chris Metcalf Acked-by: Dan Carpenter Acked-by: Daniel Vetter Acked-by: Dave Airlie Acked-by: David Herrmann Acked-by: Fabio Estevam Acked-by: Felipe Balbi Acked-by: Geert Uytterhoeven Acked-by: Gerd Hoffmann Acked-by: Grant Likely Acked-by: Guenter Roeck Acked-by: H Hartley Sweeten Acked-by: Hannes Reinecke Acked-by: Hans Verkuil Acked-by: Hans de Goede Acked-by: Hugh Dickins Acked-by: Ingo Molnar Acked-by: Jaegeuk Kim Acked-by: James Bottomley Acked-by: Jens Axboe Acked-by: Jes Sorensen Acked-by: Johan Hedberg Acked-by: Johan Hovold Acked-by: Johannes Berg Acked-by: John W. Linville Acked-by: Jonathan Corbet Acked-by: Josh Triplett Acked-by: Julia Lawall Acked-by: Kees Cook Acked-by: Kevin Hilman Acked-by: Konrad Rzeszutek Wilk Acked-by: Kristen Carlson Accardi Acked-by: Kyungmin Park Acked-by: Laurent Pinchart Acked-by: Linus Walleij Acked-by: Luis R. Rodriguez Acked-by: Magnus Damm Acked-by: Mark Brown Acked-by: Mauro Carvalho Chehab Acked-by: Maxime Ripard Acked-by: Mimi Zohar Acked-by: NeilBrown Acked-by: Olof Johansson Acked-by: Paul E. McKenney Acked-by: Rafael J. Wysocki Acked-by: Rik van Riel Acked-by: Sachin Prabhu Acked-by: Shuah Khan Acked-by: Simon Horman Acked-by: Stephen Rothwell Acked-by: Stephen Warren Acked-by: Steven Rostedt Acked-by: Takashi Iwai Acked-by: Tejun Heo Acked-by: Theodore Ts'o Acked-by: Tony Luck Acked-by: Will Deacon Acked-by: Willy Tarreau Acked-by: Zefan Li Signed-off-by: Greg Kroah-Hartman --- Documentation/CodeOfConflict | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+) create mode 100644 Documentation/CodeOfConflict diff --git a/Documentation/CodeOfConflict b/Documentation/CodeOfConflict new file mode 100644 index 000000000000..1684d0b4efa6 --- /dev/null +++ b/Documentation/CodeOfConflict @@ -0,0 +1,27 @@ +Code of Conflict +---------------- + +The Linux kernel development effort is a very personal process compared +to "traditional" ways of developing software. Your code and ideas +behind it will be carefully reviewed, often resulting in critique and +criticism. The review will almost always require improvements to the +code before it can be included in the kernel. Know that this happens +because everyone involved wants to see the best possible solution for +the overall success of Linux. This development process has been proven +to create the most robust operating system kernel ever, and we do not +want to do anything to cause the quality of submission and eventual +result to ever decrease. + +If however, anyone feels personally abused, threatened, or otherwise +uncomfortable due to this process, that is not acceptable. If so, +please contact the Linux Foundation's Technical Advisory Board at +, or the individual members, and they +will work to resolve the issue to the best of their ability. For more +information on who is on the Technical Advisory Board and what their +role is, please see: + http://www.linuxfoundation.org/programs/advisory-councils/tab + +As a reviewer of code, please strive to keep things civil and focused on +the technical issues involved. We are all humans, and frustrations can +be high on both sides of the process. Try to keep in mind the immortal +words of Bill and Ted, "Be excellent to each other." -- cgit v1.2.3-59-g8ed1b From 2b0c2e2d2a43357fc51d3499bc405d0d05df2451 Mon Sep 17 00:00:00 2001 From: Sujith Sankar Date: Wed, 25 Feb 2015 15:26:55 +0530 Subject: enic: do notify_check before returning credits We should complete notify_check before returning the credits. Once we return the credits, adaptor may access the notify data. Signed-off-by: Sujith Sankar Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller --- drivers/net/ethernet/cisco/enic/enic_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/cisco/enic/enic_main.c b/drivers/net/ethernet/cisco/enic/enic_main.c index 9cbe038a388e..a5179bfcdc2c 100644 --- a/drivers/net/ethernet/cisco/enic/enic_main.c +++ b/drivers/net/ethernet/cisco/enic/enic_main.c @@ -272,8 +272,8 @@ static irqreturn_t enic_isr_legacy(int irq, void *data) } if (ENIC_TEST_INTR(pba, notify_intr)) { - vnic_intr_return_all_credits(&enic->intr[notify_intr]); enic_notify_check(enic); + vnic_intr_return_all_credits(&enic->intr[notify_intr]); } if (ENIC_TEST_INTR(pba, err_intr)) { @@ -346,8 +346,8 @@ static irqreturn_t enic_isr_msix_notify(int irq, void *data) struct enic *enic = data; unsigned int intr = enic_msix_notify_intr(enic); - vnic_intr_return_all_credits(&enic->intr[intr]); enic_notify_check(enic); + vnic_intr_return_all_credits(&enic->intr[intr]); return IRQ_HANDLED; } -- cgit v1.2.3-59-g8ed1b From f01aa633e040e52603b8defd2263691d15b86cb0 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Wed, 25 Feb 2015 16:50:04 +0530 Subject: cxgb4: Fix PCI-E Memory window interface for big-endian systems When doing reads and writes to adapter memory via the PCI-E Memory Window interface, data gets swizzled on 4-byte boundaries on Big-Endian systems because we need to account for the register read/write interface which incorporates a swizzle onto the Little-Endian PCI-E Bus. Based on original work by Casey Leedom Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/cxgb4.h | 2 +- drivers/net/ethernet/chelsio/cxgb4/t4_hw.c | 54 ++++++++++++++++++++++++------ 2 files changed, 45 insertions(+), 11 deletions(-) diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h b/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h index d6cda17efe6e..97842d03675b 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h @@ -1103,7 +1103,7 @@ int t4_restart_aneg(struct adapter *adap, unsigned int mbox, unsigned int port); #define T4_MEMORY_WRITE 0 #define T4_MEMORY_READ 1 int t4_memory_rw(struct adapter *adap, int win, int mtype, u32 addr, u32 len, - __be32 *buf, int dir); + void *buf, int dir); static inline int t4_memory_write(struct adapter *adap, int mtype, u32 addr, u32 len, __be32 *buf) { diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c index 4d643b65265e..853c38997c82 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c @@ -449,7 +449,7 @@ int t4_edc_read(struct adapter *adap, int idx, u32 addr, __be32 *data, u64 *ecc) * @mtype: memory type: MEM_EDC0, MEM_EDC1 or MEM_MC * @addr: address within indicated memory type * @len: amount of memory to transfer - * @buf: host memory buffer + * @hbuf: host memory buffer * @dir: direction of transfer T4_MEMORY_READ (1) or T4_MEMORY_WRITE (0) * * Reads/writes an [almost] arbitrary memory region in the firmware: the @@ -460,15 +460,17 @@ int t4_edc_read(struct adapter *adap, int idx, u32 addr, __be32 *data, u64 *ecc) * caller's responsibility to perform appropriate byte order conversions. */ int t4_memory_rw(struct adapter *adap, int win, int mtype, u32 addr, - u32 len, __be32 *buf, int dir) + u32 len, void *hbuf, int dir) { u32 pos, offset, resid, memoffset; u32 edc_size, mc_size, win_pf, mem_reg, mem_aperture, mem_base; + u32 *buf; /* Argument sanity checks ... */ - if (addr & 0x3) + if (addr & 0x3 || (uintptr_t)hbuf & 0x3) return -EINVAL; + buf = (u32 *)hbuf; /* It's convenient to be able to handle lengths which aren't a * multiple of 32-bits because we often end up transferring files to @@ -532,14 +534,45 @@ int t4_memory_rw(struct adapter *adap, int win, int mtype, u32 addr, /* Transfer data to/from the adapter as long as there's an integral * number of 32-bit transfers to complete. + * + * A note on Endianness issues: + * + * The "register" reads and writes below from/to the PCI-E Memory + * Window invoke the standard adapter Big-Endian to PCI-E Link + * Little-Endian "swizzel." As a result, if we have the following + * data in adapter memory: + * + * Memory: ... | b0 | b1 | b2 | b3 | ... + * Address: i+0 i+1 i+2 i+3 + * + * Then a read of the adapter memory via the PCI-E Memory Window + * will yield: + * + * x = readl(i) + * 31 0 + * [ b3 | b2 | b1 | b0 ] + * + * If this value is stored into local memory on a Little-Endian system + * it will show up correctly in local memory as: + * + * ( ..., b0, b1, b2, b3, ... ) + * + * But on a Big-Endian system, the store will show up in memory + * incorrectly swizzled as: + * + * ( ..., b3, b2, b1, b0, ... ) + * + * So we need to account for this in the reads and writes to the + * PCI-E Memory Window below by undoing the register read/write + * swizzels. */ while (len > 0) { if (dir == T4_MEMORY_READ) - *buf++ = (__force __be32) t4_read_reg(adap, - mem_base + offset); + *buf++ = le32_to_cpu((__force __le32)t4_read_reg(adap, + mem_base + offset)); else t4_write_reg(adap, mem_base + offset, - (__force u32) *buf++); + (__force u32)cpu_to_le32(*buf++)); offset += sizeof(__be32); len -= sizeof(__be32); @@ -568,15 +601,16 @@ int t4_memory_rw(struct adapter *adap, int win, int mtype, u32 addr, */ if (resid) { union { - __be32 word; + u32 word; char byte[4]; } last; unsigned char *bp; int i; if (dir == T4_MEMORY_READ) { - last.word = (__force __be32) t4_read_reg(adap, - mem_base + offset); + last.word = le32_to_cpu( + (__force __le32)t4_read_reg(adap, + mem_base + offset)); for (bp = (unsigned char *)buf, i = resid; i < 4; i++) bp[i] = last.byte[i]; } else { @@ -584,7 +618,7 @@ int t4_memory_rw(struct adapter *adap, int win, int mtype, u32 addr, for (i = resid; i < 4; i++) last.byte[i] = 0; t4_write_reg(adap, mem_base + offset, - (__force u32) last.word); + (__force u32)cpu_to_le32(last.word)); } } -- cgit v1.2.3-59-g8ed1b From e65ad3be869b45f90a401d8ce4d4e7381c99ceb0 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Wed, 25 Feb 2015 16:35:32 +0300 Subject: rocker: add a check for NULL in rocker_probe_ports() Make sure kmalloc() succeeds. Signed-off-by: Dan Carpenter Acked-by: Scott Feldman Acked-by: Jiri Pirko Signed-off-by: David S. Miller --- drivers/net/ethernet/rocker/rocker.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/net/ethernet/rocker/rocker.c b/drivers/net/ethernet/rocker/rocker.c index 34389b6aa67c..713a13cb8c14 100644 --- a/drivers/net/ethernet/rocker/rocker.c +++ b/drivers/net/ethernet/rocker/rocker.c @@ -4201,6 +4201,8 @@ static int rocker_probe_ports(struct rocker *rocker) alloc_size = sizeof(struct rocker_port *) * rocker->port_count; rocker->ports = kmalloc(alloc_size, GFP_KERNEL); + if (!rocker->ports) + return -ENOMEM; for (i = 0; i < rocker->port_count; i++) { err = rocker_probe_port(rocker, i); if (err) -- cgit v1.2.3-59-g8ed1b From 5f2ebfbee68872762ad76f735277ed7afa074d76 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Wed, 25 Feb 2015 16:36:12 +0300 Subject: rocker: silence shift wrapping warning "val" is declared as a u64 so static checkers complain that this shift can wrap. I don't have the hardware but probably it's doesn't have over 31 ports. Still we may as well silence the warning even if it's not a real bug. Signed-off-by: Dan Carpenter Acked-by: Jiri Pirko Acked-by: Scott Feldman Signed-off-by: David S. Miller --- drivers/net/ethernet/rocker/rocker.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/rocker/rocker.c b/drivers/net/ethernet/rocker/rocker.c index 713a13cb8c14..9fb6948e14c6 100644 --- a/drivers/net/ethernet/rocker/rocker.c +++ b/drivers/net/ethernet/rocker/rocker.c @@ -1257,9 +1257,9 @@ static void rocker_port_set_enable(struct rocker_port *rocker_port, bool enable) u64 val = rocker_read64(rocker_port->rocker, PORT_PHYS_ENABLE); if (enable) - val |= 1 << rocker_port->lport; + val |= 1ULL << rocker_port->lport; else - val &= ~(1 << rocker_port->lport); + val &= ~(1ULL << rocker_port->lport); rocker_write64(rocker_port->rocker, PORT_PHYS_ENABLE, val); } -- cgit v1.2.3-59-g8ed1b From 4c5a84421c7d1c259c3883a404f9a67a2f55b003 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Wed, 25 Feb 2015 15:19:28 +0100 Subject: vhost: cleanup iterator update logic Recent iterator-related changes in vhost made it harder to follow the logic fixing up the header. In fact, the fixup always happens at the same offset: sizeof(virtio_net_hdr): sometimes the fixup iterator is updated by copy_to_iter, sometimes-by iov_iter_advance. Rearrange code to make this obvious. Signed-off-by: Michael S. Tsirkin Signed-off-by: David S. Miller --- drivers/vhost/net.c | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-) diff --git a/drivers/vhost/net.c b/drivers/vhost/net.c index afa06d28725d..ca7043459e2c 100644 --- a/drivers/vhost/net.c +++ b/drivers/vhost/net.c @@ -591,11 +591,6 @@ static void handle_rx(struct vhost_net *net) * TODO: support TSO. */ iov_iter_advance(&msg.msg_iter, vhost_hlen); - } else { - /* It'll come from socket; we'll need to patch - * ->num_buffers over if VIRTIO_NET_F_MRG_RXBUF - */ - iov_iter_advance(&fixup, sizeof(hdr)); } err = sock->ops->recvmsg(NULL, sock, &msg, sock_len, MSG_DONTWAIT | MSG_TRUNC); @@ -609,11 +604,18 @@ static void handle_rx(struct vhost_net *net) continue; } /* Supply virtio_net_hdr if VHOST_NET_F_VIRTIO_NET_HDR */ - if (unlikely(vhost_hlen) && - copy_to_iter(&hdr, sizeof(hdr), &fixup) != sizeof(hdr)) { - vq_err(vq, "Unable to write vnet_hdr at addr %p\n", - vq->iov->iov_base); - break; + if (unlikely(vhost_hlen)) { + if (copy_to_iter(&hdr, sizeof(hdr), + &fixup) != sizeof(hdr)) { + vq_err(vq, "Unable to write vnet_hdr " + "at addr %p\n", vq->iov->iov_base); + break; + } + } else { + /* Header came from socket; we'll need to patch + * ->num_buffers over if VIRTIO_NET_F_MRG_RXBUF + */ + iov_iter_advance(&fixup, sizeof(hdr)); } /* TODO: Should check and handle checksum. */ -- cgit v1.2.3-59-g8ed1b From 0d79a493e507437a2135e5ac1a447d4d503488d8 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Wed, 25 Feb 2015 15:20:01 +0100 Subject: vhost: drop hard-coded num_buffers size The 2 that we use for copy_to_iter comes from sizeof(u16), it used to be that way before the iov iter update. Fix it up, making it obvious the size of stack access is right. Signed-off-by: Michael S. Tsirkin Signed-off-by: David S. Miller --- drivers/vhost/net.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/vhost/net.c b/drivers/vhost/net.c index ca7043459e2c..2bbfc25e582c 100644 --- a/drivers/vhost/net.c +++ b/drivers/vhost/net.c @@ -621,7 +621,8 @@ static void handle_rx(struct vhost_net *net) num_buffers = cpu_to_vhost16(vq, headcount); if (likely(mergeable) && - copy_to_iter(&num_buffers, 2, &fixup) != 2) { + copy_to_iter(&num_buffers, sizeof num_buffers, + &fixup) != sizeof num_buffers) { vq_err(vq, "Failed num_buffers write"); vhost_discard_vq_desc(vq, headcount); break; -- cgit v1.2.3-59-g8ed1b From 8331de75cb13fc907ceba78e698c42150e61dda9 Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Wed, 25 Feb 2015 16:31:53 +0100 Subject: rhashtable: unconditionally grow when max_shift is not specified While commit c0c09bfdc415 ("rhashtable: avoid unnecessary wakeup for worker queue") rightfully moved part of the decision making of whether we should expand or shrink from the expand/shrink functions themselves into insert/delete functions in order to avoid unnecessary worker wake-ups, it however introduced a regression by doing so. Before that change, if no max_shift was specified (= 0) on rhashtable initialization, rhashtable_expand() would just grow unconditionally and lets the available memory be the limiting factor. After that change, if no max_shift was specified, there would be _no_ expansion step at all. Given that netlink and tipc have a max_shift specified, it was not visible there, but Josh Hunt reported that if nft that starts out with a default element hint of 3 if not otherwise provided, would slow i.e. inserts down trememdously as it cannot grow larger to relax table occupancy. Given that the test case verifies shrinks/expands manually, we also must remove pointer to the helper functions to explicitly avoid parallel resizing on insertions/deletions. test_bucket_stats() and test_rht_lookup() could also be wrapped around rhashtable mutex to explicitly synchronize a walk from resizing, but I think that defeats the actual test case which intended to have explicit test steps, i.e. 1) inserts, 2) expands, 3) shrinks, 4) deletions, with object verification after each stage. Reported-by: Josh Hunt Fixes: c0c09bfdc415 ("rhashtable: avoid unnecessary wakeup for worker queue") Signed-off-by: Daniel Borkmann Cc: Ying Xue Cc: Josh Hunt Acked-by: Thomas Graf Signed-off-by: David S. Miller --- lib/rhashtable.c | 2 +- lib/test_rhashtable.c | 2 -- 2 files changed, 1 insertion(+), 3 deletions(-) diff --git a/lib/rhashtable.c b/lib/rhashtable.c index e3a04e4b3ec5..bcf119bfdef4 100644 --- a/lib/rhashtable.c +++ b/lib/rhashtable.c @@ -251,7 +251,7 @@ bool rht_grow_above_75(const struct rhashtable *ht, size_t new_size) { /* Expand table when exceeding 75% load */ return atomic_read(&ht->nelems) > (new_size / 4 * 3) && - (ht->p.max_shift && atomic_read(&ht->shift) < ht->p.max_shift); + (!ht->p.max_shift || atomic_read(&ht->shift) < ht->p.max_shift); } EXPORT_SYMBOL_GPL(rht_grow_above_75); diff --git a/lib/test_rhashtable.c b/lib/test_rhashtable.c index 58b995323c44..f9e9d734446a 100644 --- a/lib/test_rhashtable.c +++ b/lib/test_rhashtable.c @@ -202,8 +202,6 @@ static int __init test_rht_init(void) .key_len = sizeof(int), .hashfn = jhash, .nulls_base = (3U << RHT_BASE_SHIFT), - .grow_decision = rht_grow_above_75, - .shrink_decision = rht_shrink_below_30, }; int err; -- cgit v1.2.3-59-g8ed1b From 4c4b52d9b2df45e8216d3e30b5452e4a364d2cac Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Wed, 25 Feb 2015 16:31:54 +0100 Subject: rhashtable: remove indirection for grow/shrink decision functions Currently, all real users of rhashtable default their grow and shrink decision functions to rht_grow_above_75() and rht_shrink_below_30(), so that there's currently no need to have this explicitly selectable. It can/should be generic and private inside rhashtable until a real use case pops up. Since we can make this private, we'll save us this additional indirection layer and can improve insertion/deletion time as well. Reference: http://patchwork.ozlabs.org/patch/443040/ Suggested-by: David S. Miller Signed-off-by: Daniel Borkmann Acked-by: Thomas Graf Signed-off-by: David S. Miller --- include/linux/rhashtable.h | 13 ----------- lib/rhashtable.c | 56 ++++++++++++++-------------------------------- lib/test_rhashtable.c | 1 + net/netfilter/nft_hash.c | 2 -- net/netlink/af_netlink.c | 2 -- net/tipc/socket.c | 2 -- 6 files changed, 18 insertions(+), 58 deletions(-) diff --git a/include/linux/rhashtable.h b/include/linux/rhashtable.h index cb2104be2135..d438eeb08bff 100644 --- a/include/linux/rhashtable.h +++ b/include/linux/rhashtable.h @@ -79,12 +79,6 @@ struct rhashtable; * @locks_mul: Number of bucket locks to allocate per cpu (default: 128) * @hashfn: Function to hash key * @obj_hashfn: Function to hash object - * @grow_decision: If defined, may return true if table should expand - * @shrink_decision: If defined, may return true if table should shrink - * - * Note: when implementing the grow and shrink decision function, min/max - * shift must be enforced, otherwise, resizing watermarks they set may be - * useless. */ struct rhashtable_params { size_t nelem_hint; @@ -98,10 +92,6 @@ struct rhashtable_params { size_t locks_mul; rht_hashfn_t hashfn; rht_obj_hashfn_t obj_hashfn; - bool (*grow_decision)(const struct rhashtable *ht, - size_t new_size); - bool (*shrink_decision)(const struct rhashtable *ht, - size_t new_size); }; /** @@ -193,9 +183,6 @@ int rhashtable_init(struct rhashtable *ht, struct rhashtable_params *params); void rhashtable_insert(struct rhashtable *ht, struct rhash_head *node); bool rhashtable_remove(struct rhashtable *ht, struct rhash_head *node); -bool rht_grow_above_75(const struct rhashtable *ht, size_t new_size); -bool rht_shrink_below_30(const struct rhashtable *ht, size_t new_size); - int rhashtable_expand(struct rhashtable *ht); int rhashtable_shrink(struct rhashtable *ht); diff --git a/lib/rhashtable.c b/lib/rhashtable.c index bcf119bfdef4..090641db4c0d 100644 --- a/lib/rhashtable.c +++ b/lib/rhashtable.c @@ -247,26 +247,24 @@ static struct bucket_table *bucket_table_alloc(struct rhashtable *ht, * @ht: hash table * @new_size: new table size */ -bool rht_grow_above_75(const struct rhashtable *ht, size_t new_size) +static bool rht_grow_above_75(const struct rhashtable *ht, size_t new_size) { /* Expand table when exceeding 75% load */ return atomic_read(&ht->nelems) > (new_size / 4 * 3) && (!ht->p.max_shift || atomic_read(&ht->shift) < ht->p.max_shift); } -EXPORT_SYMBOL_GPL(rht_grow_above_75); /** * rht_shrink_below_30 - returns true if nelems < 0.3 * table-size * @ht: hash table * @new_size: new table size */ -bool rht_shrink_below_30(const struct rhashtable *ht, size_t new_size) +static bool rht_shrink_below_30(const struct rhashtable *ht, size_t new_size) { /* Shrink table beneath 30% load */ return atomic_read(&ht->nelems) < (new_size * 3 / 10) && (atomic_read(&ht->shift) > ht->p.min_shift); } -EXPORT_SYMBOL_GPL(rht_shrink_below_30); static void lock_buckets(struct bucket_table *new_tbl, struct bucket_table *old_tbl, unsigned int hash) @@ -528,40 +526,19 @@ static void rht_deferred_worker(struct work_struct *work) list_for_each_entry(walker, &ht->walkers, list) walker->resize = true; - if (ht->p.grow_decision && ht->p.grow_decision(ht, tbl->size)) + if (rht_grow_above_75(ht, tbl->size)) rhashtable_expand(ht); - else if (ht->p.shrink_decision && ht->p.shrink_decision(ht, tbl->size)) + else if (rht_shrink_below_30(ht, tbl->size)) rhashtable_shrink(ht); - unlock: mutex_unlock(&ht->mutex); } -static void rhashtable_probe_expand(struct rhashtable *ht) -{ - const struct bucket_table *new_tbl = rht_dereference_rcu(ht->future_tbl, ht); - const struct bucket_table *tbl = rht_dereference_rcu(ht->tbl, ht); - - /* Only adjust the table if no resizing is currently in progress. */ - if (tbl == new_tbl && ht->p.grow_decision && - ht->p.grow_decision(ht, tbl->size)) - schedule_work(&ht->run_work); -} - -static void rhashtable_probe_shrink(struct rhashtable *ht) -{ - const struct bucket_table *new_tbl = rht_dereference_rcu(ht->future_tbl, ht); - const struct bucket_table *tbl = rht_dereference_rcu(ht->tbl, ht); - - /* Only adjust the table if no resizing is currently in progress. */ - if (tbl == new_tbl && ht->p.shrink_decision && - ht->p.shrink_decision(ht, tbl->size)) - schedule_work(&ht->run_work); -} - static void __rhashtable_insert(struct rhashtable *ht, struct rhash_head *obj, - struct bucket_table *tbl, u32 hash) + struct bucket_table *tbl, + const struct bucket_table *old_tbl, u32 hash) { + bool no_resize_running = tbl == old_tbl; struct rhash_head *head; hash = rht_bucket_index(tbl, hash); @@ -577,8 +554,8 @@ static void __rhashtable_insert(struct rhashtable *ht, struct rhash_head *obj, rcu_assign_pointer(tbl->buckets[hash], obj); atomic_inc(&ht->nelems); - - rhashtable_probe_expand(ht); + if (no_resize_running && rht_grow_above_75(ht, tbl->size)) + schedule_work(&ht->run_work); } /** @@ -608,7 +585,7 @@ void rhashtable_insert(struct rhashtable *ht, struct rhash_head *obj) hash = obj_raw_hashfn(ht, rht_obj(ht, obj)); lock_buckets(tbl, old_tbl, hash); - __rhashtable_insert(ht, obj, tbl, hash); + __rhashtable_insert(ht, obj, tbl, old_tbl, hash); unlock_buckets(tbl, old_tbl, hash); rcu_read_unlock(); @@ -690,8 +667,11 @@ found: unlock_buckets(new_tbl, old_tbl, new_hash); if (ret) { + bool no_resize_running = new_tbl == old_tbl; + atomic_dec(&ht->nelems); - rhashtable_probe_shrink(ht); + if (no_resize_running && rht_shrink_below_30(ht, new_tbl->size)) + schedule_work(&ht->run_work); } rcu_read_unlock(); @@ -861,7 +841,7 @@ bool rhashtable_lookup_compare_insert(struct rhashtable *ht, goto exit; } - __rhashtable_insert(ht, obj, new_tbl, new_hash); + __rhashtable_insert(ht, obj, new_tbl, old_tbl, new_hash); exit: unlock_buckets(new_tbl, old_tbl, new_hash); @@ -1123,8 +1103,7 @@ int rhashtable_init(struct rhashtable *ht, struct rhashtable_params *params) if (!ht->p.hash_rnd) get_random_bytes(&ht->p.hash_rnd, sizeof(ht->p.hash_rnd)); - if (ht->p.grow_decision || ht->p.shrink_decision) - INIT_WORK(&ht->run_work, rht_deferred_worker); + INIT_WORK(&ht->run_work, rht_deferred_worker); return 0; } @@ -1142,8 +1121,7 @@ void rhashtable_destroy(struct rhashtable *ht) { ht->being_destroyed = true; - if (ht->p.grow_decision || ht->p.shrink_decision) - cancel_work_sync(&ht->run_work); + cancel_work_sync(&ht->run_work); mutex_lock(&ht->mutex); bucket_table_free(rht_dereference(ht->tbl, ht)); diff --git a/lib/test_rhashtable.c b/lib/test_rhashtable.c index f9e9d734446a..67c7593d1dd6 100644 --- a/lib/test_rhashtable.c +++ b/lib/test_rhashtable.c @@ -201,6 +201,7 @@ static int __init test_rht_init(void) .key_offset = offsetof(struct test_obj, value), .key_len = sizeof(int), .hashfn = jhash, + .max_shift = 1, /* we expand/shrink manually here */ .nulls_base = (3U << RHT_BASE_SHIFT), }; int err; diff --git a/net/netfilter/nft_hash.c b/net/netfilter/nft_hash.c index 61e6c407476a..c82df0a48fcd 100644 --- a/net/netfilter/nft_hash.c +++ b/net/netfilter/nft_hash.c @@ -192,8 +192,6 @@ static int nft_hash_init(const struct nft_set *set, .key_offset = offsetof(struct nft_hash_elem, key), .key_len = set->klen, .hashfn = jhash, - .grow_decision = rht_grow_above_75, - .shrink_decision = rht_shrink_below_30, }; return rhashtable_init(priv, ¶ms); diff --git a/net/netlink/af_netlink.c b/net/netlink/af_netlink.c index 2702673f0f23..05919bf3f670 100644 --- a/net/netlink/af_netlink.c +++ b/net/netlink/af_netlink.c @@ -3126,8 +3126,6 @@ static int __init netlink_proto_init(void) .key_len = sizeof(u32), /* portid */ .hashfn = jhash, .max_shift = 16, /* 64K */ - .grow_decision = rht_grow_above_75, - .shrink_decision = rht_shrink_below_30, }; if (err != 0) diff --git a/net/tipc/socket.c b/net/tipc/socket.c index f73e975af80b..b4d4467d0bb0 100644 --- a/net/tipc/socket.c +++ b/net/tipc/socket.c @@ -2364,8 +2364,6 @@ int tipc_sk_rht_init(struct net *net) .hashfn = jhash, .max_shift = 20, /* 1M */ .min_shift = 8, /* 256 */ - .grow_decision = rht_grow_above_75, - .shrink_decision = rht_shrink_below_30, }; return rhashtable_init(&tn->sk_rht, &rht_params); -- cgit v1.2.3-59-g8ed1b From be36e185bd26388355d3ea1847278b96ab350792 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Fri, 27 Feb 2015 17:04:17 -0500 Subject: NFSv4: nfs4_open_recover_helper() must set share access The share access mode is now specified as an argument in the nfs4_opendata, and so nfs4_open_recover_helper() needs to call nfs4_map_atomic_open_share() in order to set it. Fixes: 6ae373394c42 ("NFSv4.1: Ask for no delegation on OPEN if using O_DIRECT") Signed-off-by: Trond Myklebust --- fs/nfs/nfs4proc.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index 88180ac5ea0e..4e41340e957d 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -1552,6 +1552,9 @@ static int nfs4_open_recover_helper(struct nfs4_opendata *opendata, fmode_t fmod opendata->o_arg.open_flags = 0; opendata->o_arg.fmode = fmode; + opendata->o_arg.share_access = nfs4_map_atomic_open_share( + NFS_SB(opendata->dentry->d_sb), + fmode, 0); memset(&opendata->o_res, 0, sizeof(opendata->o_res)); memset(&opendata->c_res, 0, sizeof(opendata->c_res)); nfs4_init_opendata_res(opendata); -- cgit v1.2.3-59-g8ed1b From 7488c3e3d8384e6a3d71c6a05645b3db8d82d275 Mon Sep 17 00:00:00 2001 From: Luca Ceresoli Date: Thu, 26 Feb 2015 00:58:12 +0100 Subject: net: asix: add support for the Sitecom LN-028 USB adapter Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one shows up in lsusb as: "Sitecom Europe B.V. LN-028 Network USB 2.0 Adapter". Signed-off-by: Luca Ceresoli Cc: Francois Romieu Cc: "David S. Miller" Cc: linux-usb@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller --- drivers/net/usb/Kconfig | 1 + drivers/net/usb/asix_devices.c | 4 ++++ 2 files changed, 5 insertions(+) diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig index 37eed4d84e9c..0732f9e16128 100644 --- a/drivers/net/usb/Kconfig +++ b/drivers/net/usb/Kconfig @@ -161,6 +161,7 @@ config USB_NET_AX8817X * Linksys USB200M * Netgear FA120 * Sitecom LN-029 + * Sitecom LN-028 * Intellinet USB 2.0 Ethernet * ST Lab USB 2.0 Ethernet * TrendNet TU2-ET100 diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c index bf49792062a2..1173a24feda3 100644 --- a/drivers/net/usb/asix_devices.c +++ b/drivers/net/usb/asix_devices.c @@ -978,6 +978,10 @@ static const struct usb_device_id products [] = { // Sitecom LN-031 "USB 2.0 10/100/1000 Ethernet adapter" USB_DEVICE (0x0df6, 0x0056), .driver_info = (unsigned long) &ax88178_info, +}, { + // Sitecom LN-028 "USB 2.0 10/100/1000 Ethernet adapter" + USB_DEVICE (0x0df6, 0x061c), + .driver_info = (unsigned long) &ax88178_info, }, { // corega FEther USB2-TX USB_DEVICE (0x07aa, 0x0017), -- cgit v1.2.3-59-g8ed1b From c30e76a728beb5bbfff0ddeb573e28927853d4b8 Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Wed, 25 Feb 2015 13:50:12 -0600 Subject: amd-xgbe: Request IRQs only after driver is fully setup It is possible that the hardware may not have been properly shutdown before this driver gets control, through use by firmware, for example. Until the driver is loaded, interrupts associated with the hardware could go pending. When the IRQs are requested napi support has not been initialized yet, but the ISR will get control and schedule napi processing resulting in a kernel panic because the poll routine has not been set. Adjust the code so that the driver is fully ready to handle and process interrupts as soon as the IRQs are requested. This involves requesting and freeing IRQs during start and stop processing and ordering the napi add and delete calls appropriately. Also adjust the powerup and powerdown routines to match the start and stop routines in regards to the ordering of tasks, including napi related calls. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-drv.c | 175 ++++++++++++++++--------------- 1 file changed, 93 insertions(+), 82 deletions(-) diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-drv.c b/drivers/net/ethernet/amd/xgbe/xgbe-drv.c index b93d4404d975..885b02b5be07 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-drv.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-drv.c @@ -609,6 +609,68 @@ static void xgbe_napi_disable(struct xgbe_prv_data *pdata, unsigned int del) } } +static int xgbe_request_irqs(struct xgbe_prv_data *pdata) +{ + struct xgbe_channel *channel; + struct net_device *netdev = pdata->netdev; + unsigned int i; + int ret; + + ret = devm_request_irq(pdata->dev, pdata->dev_irq, xgbe_isr, 0, + netdev->name, pdata); + if (ret) { + netdev_alert(netdev, "error requesting irq %d\n", + pdata->dev_irq); + return ret; + } + + if (!pdata->per_channel_irq) + return 0; + + channel = pdata->channel; + for (i = 0; i < pdata->channel_count; i++, channel++) { + snprintf(channel->dma_irq_name, + sizeof(channel->dma_irq_name) - 1, + "%s-TxRx-%u", netdev_name(netdev), + channel->queue_index); + + ret = devm_request_irq(pdata->dev, channel->dma_irq, + xgbe_dma_isr, 0, + channel->dma_irq_name, channel); + if (ret) { + netdev_alert(netdev, "error requesting irq %d\n", + channel->dma_irq); + goto err_irq; + } + } + + return 0; + +err_irq: + /* Using an unsigned int, 'i' will go to UINT_MAX and exit */ + for (i--, channel--; i < pdata->channel_count; i--, channel--) + devm_free_irq(pdata->dev, channel->dma_irq, channel); + + devm_free_irq(pdata->dev, pdata->dev_irq, pdata); + + return ret; +} + +static void xgbe_free_irqs(struct xgbe_prv_data *pdata) +{ + struct xgbe_channel *channel; + unsigned int i; + + devm_free_irq(pdata->dev, pdata->dev_irq, pdata); + + if (!pdata->per_channel_irq) + return; + + channel = pdata->channel; + for (i = 0; i < pdata->channel_count; i++, channel++) + devm_free_irq(pdata->dev, channel->dma_irq, channel); +} + void xgbe_init_tx_coalesce(struct xgbe_prv_data *pdata) { struct xgbe_hw_if *hw_if = &pdata->hw_if; @@ -810,20 +872,20 @@ int xgbe_powerdown(struct net_device *netdev, unsigned int caller) return -EINVAL; } - phy_stop(pdata->phydev); - spin_lock_irqsave(&pdata->lock, flags); if (caller == XGMAC_DRIVER_CONTEXT) netif_device_detach(netdev); netif_tx_stop_all_queues(netdev); - xgbe_napi_disable(pdata, 0); - /* Powerdown Tx/Rx */ hw_if->powerdown_tx(pdata); hw_if->powerdown_rx(pdata); + xgbe_napi_disable(pdata, 0); + + phy_stop(pdata->phydev); + pdata->power_down = 1; spin_unlock_irqrestore(&pdata->lock, flags); @@ -854,14 +916,14 @@ int xgbe_powerup(struct net_device *netdev, unsigned int caller) phy_start(pdata->phydev); - /* Enable Tx/Rx */ + xgbe_napi_enable(pdata, 0); + hw_if->powerup_tx(pdata); hw_if->powerup_rx(pdata); if (caller == XGMAC_DRIVER_CONTEXT) netif_device_attach(netdev); - xgbe_napi_enable(pdata, 0); netif_tx_start_all_queues(netdev); spin_unlock_irqrestore(&pdata->lock, flags); @@ -875,6 +937,7 @@ static int xgbe_start(struct xgbe_prv_data *pdata) { struct xgbe_hw_if *hw_if = &pdata->hw_if; struct net_device *netdev = pdata->netdev; + int ret; DBGPR("-->xgbe_start\n"); @@ -884,17 +947,31 @@ static int xgbe_start(struct xgbe_prv_data *pdata) phy_start(pdata->phydev); + xgbe_napi_enable(pdata, 1); + + ret = xgbe_request_irqs(pdata); + if (ret) + goto err_napi; + hw_if->enable_tx(pdata); hw_if->enable_rx(pdata); xgbe_init_tx_timers(pdata); - xgbe_napi_enable(pdata, 1); netif_tx_start_all_queues(netdev); DBGPR("<--xgbe_start\n"); return 0; + +err_napi: + xgbe_napi_disable(pdata, 1); + + phy_stop(pdata->phydev); + + hw_if->exit(pdata); + + return ret; } static void xgbe_stop(struct xgbe_prv_data *pdata) @@ -907,16 +984,21 @@ static void xgbe_stop(struct xgbe_prv_data *pdata) DBGPR("-->xgbe_stop\n"); - phy_stop(pdata->phydev); - netif_tx_stop_all_queues(netdev); - xgbe_napi_disable(pdata, 1); xgbe_stop_tx_timers(pdata); hw_if->disable_tx(pdata); hw_if->disable_rx(pdata); + xgbe_free_irqs(pdata); + + xgbe_napi_disable(pdata, 1); + + phy_stop(pdata->phydev); + + hw_if->exit(pdata); + channel = pdata->channel; for (i = 0; i < pdata->channel_count; i++, channel++) { if (!channel->tx_ring) @@ -931,10 +1013,6 @@ static void xgbe_stop(struct xgbe_prv_data *pdata) static void xgbe_restart_dev(struct xgbe_prv_data *pdata) { - struct xgbe_channel *channel; - struct xgbe_hw_if *hw_if = &pdata->hw_if; - unsigned int i; - DBGPR("-->xgbe_restart_dev\n"); /* If not running, "restart" will happen on open */ @@ -942,19 +1020,10 @@ static void xgbe_restart_dev(struct xgbe_prv_data *pdata) return; xgbe_stop(pdata); - synchronize_irq(pdata->dev_irq); - if (pdata->per_channel_irq) { - channel = pdata->channel; - for (i = 0; i < pdata->channel_count; i++, channel++) - synchronize_irq(channel->dma_irq); - } xgbe_free_tx_data(pdata); xgbe_free_rx_data(pdata); - /* Issue software reset to device */ - hw_if->exit(pdata); - xgbe_start(pdata); DBGPR("<--xgbe_restart_dev\n"); @@ -1283,10 +1352,7 @@ static void xgbe_packet_info(struct xgbe_prv_data *pdata, static int xgbe_open(struct net_device *netdev) { struct xgbe_prv_data *pdata = netdev_priv(netdev); - struct xgbe_hw_if *hw_if = &pdata->hw_if; struct xgbe_desc_if *desc_if = &pdata->desc_if; - struct xgbe_channel *channel = NULL; - unsigned int i = 0; int ret; DBGPR("-->xgbe_open\n"); @@ -1329,55 +1395,14 @@ static int xgbe_open(struct net_device *netdev) INIT_WORK(&pdata->restart_work, xgbe_restart); INIT_WORK(&pdata->tx_tstamp_work, xgbe_tx_tstamp); - /* Request interrupts */ - ret = devm_request_irq(pdata->dev, pdata->dev_irq, xgbe_isr, 0, - netdev->name, pdata); - if (ret) { - netdev_alert(netdev, "error requesting irq %d\n", - pdata->dev_irq); - goto err_rings; - } - - if (pdata->per_channel_irq) { - channel = pdata->channel; - for (i = 0; i < pdata->channel_count; i++, channel++) { - snprintf(channel->dma_irq_name, - sizeof(channel->dma_irq_name) - 1, - "%s-TxRx-%u", netdev_name(netdev), - channel->queue_index); - - ret = devm_request_irq(pdata->dev, channel->dma_irq, - xgbe_dma_isr, 0, - channel->dma_irq_name, channel); - if (ret) { - netdev_alert(netdev, - "error requesting irq %d\n", - channel->dma_irq); - goto err_irq; - } - } - } - ret = xgbe_start(pdata); if (ret) - goto err_start; + goto err_rings; DBGPR("<--xgbe_open\n"); return 0; -err_start: - hw_if->exit(pdata); - -err_irq: - if (pdata->per_channel_irq) { - /* Using an unsigned int, 'i' will go to UINT_MAX and exit */ - for (i--, channel--; i < pdata->channel_count; i--, channel--) - devm_free_irq(pdata->dev, channel->dma_irq, channel); - } - - devm_free_irq(pdata->dev, pdata->dev_irq, pdata); - err_rings: desc_if->free_ring_resources(pdata); @@ -1399,30 +1424,16 @@ err_phy_init: static int xgbe_close(struct net_device *netdev) { struct xgbe_prv_data *pdata = netdev_priv(netdev); - struct xgbe_hw_if *hw_if = &pdata->hw_if; struct xgbe_desc_if *desc_if = &pdata->desc_if; - struct xgbe_channel *channel; - unsigned int i; DBGPR("-->xgbe_close\n"); /* Stop the device */ xgbe_stop(pdata); - /* Issue software reset to device */ - hw_if->exit(pdata); - /* Free the ring descriptors and buffers */ desc_if->free_ring_resources(pdata); - /* Release the interrupts */ - devm_free_irq(pdata->dev, pdata->dev_irq, pdata); - if (pdata->per_channel_irq) { - channel = pdata->channel; - for (i = 0; i < pdata->channel_count; i++, channel++) - devm_free_irq(pdata->dev, channel->dma_irq, channel); - } - /* Free the channel and ring structures */ xgbe_free_channels(pdata); -- cgit v1.2.3-59-g8ed1b From 5beb5c90c1f54d745da040aa05634a5830ba4a4c Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 26 Feb 2015 07:20:34 -0800 Subject: rhashtable: use cond_resched() If a hash table has 128 slots and 16384 elems, expand to 256 slots takes more than one second. For larger sets, a soft lockup is detected. Holding cpu for that long, even in a work queue is a show stopper for non preemptable kernels. cond_resched() at strategic points to allow process scheduler to reschedule us. Signed-off-by: Eric Dumazet Acked-by: Daniel Borkmann Signed-off-by: David S. Miller --- lib/rhashtable.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/lib/rhashtable.c b/lib/rhashtable.c index 090641db4c0d..b5344ef4c684 100644 --- a/lib/rhashtable.c +++ b/lib/rhashtable.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include #include @@ -412,6 +413,7 @@ int rhashtable_expand(struct rhashtable *ht) } } unlock_buckets(new_tbl, old_tbl, new_hash); + cond_resched(); } /* Unzip interleaved hash chains */ @@ -435,6 +437,7 @@ int rhashtable_expand(struct rhashtable *ht) complete = false; unlock_buckets(new_tbl, old_tbl, old_hash); + cond_resched(); } } @@ -493,6 +496,7 @@ int rhashtable_shrink(struct rhashtable *ht) tbl->buckets[new_hash + new_tbl->size]); unlock_buckets(new_tbl, tbl, new_hash); + cond_resched(); } /* Publish the new, valid hash table */ -- cgit v1.2.3-59-g8ed1b From f1651a24280997c75836b4380bcbf60fd2aa34fd Mon Sep 17 00:00:00 2001 From: Joachim Nilsson Date: Wed, 25 Feb 2015 16:15:02 +0100 Subject: PCI: versatile: Update for list_for_each_entry() API change In Linux 4.0-rc1 ARM Versatile PCI build fails to build due to what appears to be an API update. This patch is a very simple correction, merely posted as a heads-up to the maintainers. Hopefully a better fix can be forwarded to Linus. [ arnd: the patch actually looks correct, so let's take this version ] Signed-off-by: Joachim Nilsson Signed-off-by: Arnd Bergmann Acked-by: Linus Walleij Acked-by: Bjorn Helgaas Signed-off-by: Rafael J. Wysocki --- drivers/pci/host/pci-versatile.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/pci/host/pci-versatile.c b/drivers/pci/host/pci-versatile.c index 1ec694a52379..464bf492ee2a 100644 --- a/drivers/pci/host/pci-versatile.c +++ b/drivers/pci/host/pci-versatile.c @@ -80,7 +80,7 @@ static int versatile_pci_parse_request_of_pci_ranges(struct device *dev, if (err) return err; - resource_list_for_each_entry(win, res, list) { + resource_list_for_each_entry(win, res) { struct resource *parent, *res = win->res; switch (resource_type(res)) { -- cgit v1.2.3-59-g8ed1b From 4cc32cb4e92622757685c8732bdfc400243a5644 Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:29 -0800 Subject: tools/thermal: tmon: add --target-temp parameter If we launch in daemon mode (--daemon), we don't have the ncurses UI, but we might want to set the target temperature still. For example, someone might stick the following in their boot script: tmon --control intel_powerclamp --target-temp 90 --log --daemon This would turn on CPU idle injection when we're around 90 degrees celsius, and would log temperature and throttling info to /var/tmp/tmon.log. Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/tmon.8 | 2 ++ tools/thermal/tmon/tmon.c | 14 ++++++++++++-- 2 files changed, 14 insertions(+), 2 deletions(-) diff --git a/tools/thermal/tmon/tmon.8 b/tools/thermal/tmon/tmon.8 index 0be727cb9892..02d5179803aa 100644 --- a/tools/thermal/tmon/tmon.8 +++ b/tools/thermal/tmon/tmon.8 @@ -55,6 +55,8 @@ The \fB-l --log\fP option write data to /var/tmp/tmon.log .PP The \fB-t --time-interval\fP option sets the polling interval in seconds .PP +The \fB-T --target-temp\fP option sets the initial target temperature +.PP The \fB-v --version\fP option shows the version of \fBtmon \fP .PP The \fB-z --zone\fP option sets the target therma zone instance to be controlled diff --git a/tools/thermal/tmon/tmon.c b/tools/thermal/tmon/tmon.c index 09b7c3218334..9aa19652e8e8 100644 --- a/tools/thermal/tmon/tmon.c +++ b/tools/thermal/tmon/tmon.c @@ -64,6 +64,7 @@ void usage() printf(" -h, --help show this help message\n"); printf(" -l, --log log data to /var/tmp/tmon.log\n"); printf(" -t, --time-interval sampling time interval, > 1 sec.\n"); + printf(" -T, --target-temp initial target temperature\n"); printf(" -v, --version show version\n"); printf(" -z, --zone target thermal zone id\n"); @@ -219,6 +220,7 @@ static struct option opts[] = { { "control", 1, NULL, 'c' }, { "daemon", 0, NULL, 'd' }, { "time-interval", 1, NULL, 't' }, + { "target-temp", 1, NULL, 'T' }, { "log", 0, NULL, 'l' }, { "help", 0, NULL, 'h' }, { "version", 0, NULL, 'v' }, @@ -231,7 +233,7 @@ int main(int argc, char **argv) { int err = 0; int id2 = 0, c; - double yk = 0.0; /* controller output */ + double yk = 0.0, temp; /* controller output */ int target_tz_index; if (geteuid() != 0) { @@ -239,7 +241,7 @@ int main(int argc, char **argv) exit(EXIT_FAILURE); } - while ((c = getopt_long(argc, argv, "c:dlht:vgz:", opts, &id2)) != -1) { + while ((c = getopt_long(argc, argv, "c:dlht:T:vgz:", opts, &id2)) != -1) { switch (c) { case 'c': no_control = 0; @@ -254,6 +256,14 @@ int main(int argc, char **argv) if (ticktime < 1) ticktime = 1; break; + case 'T': + temp = strtod(optarg, NULL); + if (temp < 0) { + fprintf(stderr, "error: temperature must be positive\n"); + return 1; + } + target_temp_user = temp; + break; case 'l': printf("Logging data to /var/tmp/tmon.log\n"); logging = 1; -- cgit v1.2.3-59-g8ed1b From a90b6b006c616f1a33f8ffb6939e31c8d66926a4 Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:30 -0800 Subject: tools/thermal: tmon: add min/max macros Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/tui.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/tools/thermal/tmon/tui.c b/tools/thermal/tmon/tui.c index 89f8ef0e15c8..43c5aecf71da 100644 --- a/tools/thermal/tmon/tui.c +++ b/tools/thermal/tmon/tui.c @@ -30,6 +30,18 @@ #include "tmon.h" +#define min(x, y) ({ \ + typeof(x) _min1 = (x); \ + typeof(y) _min2 = (y); \ + (void) (&_min1 == &_min2); \ + _min1 < _min2 ? _min1 : _min2; }) + +#define max(x, y) ({ \ + typeof(x) _max1 = (x); \ + typeof(y) _max2 = (y); \ + (void) (&_max1 == &_max2); \ + _max1 > _max2 ? _max1 : _max2; }) + static PANEL *data_panel; static PANEL *dialogue_panel; static PANEL *top; -- cgit v1.2.3-59-g8ed1b From 0e7b766dc0aeedd47c8264242e06f3a470f5d589 Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:31 -0800 Subject: tools/thermal: tmon: tui: don't hard-code dialog window size assumptions We can use the ncurses API to get the number of rows. Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/tui.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/tools/thermal/tmon/tui.c b/tools/thermal/tmon/tui.c index 43c5aecf71da..2779573a53cb 100644 --- a/tools/thermal/tmon/tui.c +++ b/tools/thermal/tmon/tui.c @@ -274,11 +274,14 @@ const char DIAG_TITLE[] = "[ TUNABLES ]"; void show_dialogue(void) { int j, x = 0, y = 0; + int rows, cols; WINDOW *w = dialogue_window; if (tui_disabled || !w) return; + getmaxyx(w, rows, cols); + werase(w); box(w, 0, 0); mvwprintw(w, 0, maxx/4, DIAG_TITLE); @@ -297,10 +300,8 @@ void show_dialogue(void) wattron(w, A_BOLD); mvwprintw(w, DIAG_DEV_ROWS+1, 1, "Enter Choice [A-Z]?"); wattroff(w, A_BOLD); - /* y size of dialogue win is nr cdev + 5, so print legend - * at the bottom line - */ - mvwprintw(w, ptdata.nr_cooling_dev+3, 1, + /* print legend at the bottom line */ + mvwprintw(w, rows - 2, 1, "Legend: A=Active, P=Passive, C=Critical"); wrefresh(dialogue_window); -- cgit v1.2.3-59-g8ed1b From 3bbcc529ee7f1d5807f3fe84cfdbdd1599530ad0 Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:32 -0800 Subject: tools/thermal: tmon: fixup tui windowing calculations The number of rows in the dialog vary according to the number of cooling devices. However, some of the windowing computations were assuming a fixed number of rows. This computation is OK when we have between 4 and 9 cooling devices (and they wrap to the next column), but with fewer devices, we end up printing off the end of the window. This unifies the row computation into a single function and uses that throughout the TUI code. This also accounts for increasing the number of rows when there are more than 9 total cooling devices. Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/tui.c | 21 ++++++++++++++++----- 1 file changed, 16 insertions(+), 5 deletions(-) diff --git a/tools/thermal/tmon/tui.c b/tools/thermal/tmon/tui.c index 2779573a53cb..36e1f86c8452 100644 --- a/tools/thermal/tmon/tui.c +++ b/tools/thermal/tmon/tui.c @@ -110,6 +110,18 @@ void write_status_bar(int x, char *line) wrefresh(status_bar_window); } +/* wrap at 5 */ +#define DIAG_DEV_ROWS 5 +/* + * list cooling devices + "set temp" entry; wraps after 5 rows, if they fit + */ +static int diag_dev_rows(void) +{ + int entries = ptdata.nr_cooling_dev + 1; + int rows = max(DIAG_DEV_ROWS, (entries + 1) / 2); + return min(rows, entries); +} + void setup_windows(void) { int y_begin = 1; @@ -134,7 +146,7 @@ void setup_windows(void) * dialogue window is a pop-up, when needed it lays on top of cdev win */ - dialogue_window = subwin(stdscr, ptdata.nr_cooling_dev+5, maxx-50, + dialogue_window = subwin(stdscr, diag_dev_rows() + 5, maxx-50, DIAG_Y, DIAG_X); thermal_data_window = subwin(stdscr, ptdata.nr_tz_sensor * @@ -270,7 +282,6 @@ void show_cooling_device(void) } const char DIAG_TITLE[] = "[ TUNABLES ]"; -#define DIAG_DEV_ROWS 5 void show_dialogue(void) { int j, x = 0, y = 0; @@ -287,7 +298,7 @@ void show_dialogue(void) mvwprintw(w, 0, maxx/4, DIAG_TITLE); /* list all the available tunables */ for (j = 0; j <= ptdata.nr_cooling_dev; j++) { - y = j % DIAG_DEV_ROWS; + y = j % diag_dev_rows(); if (y == 0 && j != 0) x += 20; if (j == ptdata.nr_cooling_dev) @@ -298,7 +309,7 @@ void show_dialogue(void) ptdata.cdi[j].type, ptdata.cdi[j].instance); } wattron(w, A_BOLD); - mvwprintw(w, DIAG_DEV_ROWS+1, 1, "Enter Choice [A-Z]?"); + mvwprintw(w, diag_dev_rows()+1, 1, "Enter Choice [A-Z]?"); wattroff(w, A_BOLD); /* print legend at the bottom line */ mvwprintw(w, rows - 2, 1, @@ -450,7 +461,7 @@ static void handle_input_choice(int ch) snprintf(buf, sizeof(buf), "New Value for %.10s-%2d: ", ptdata.cdi[cdev_id].type, ptdata.cdi[cdev_id].instance); - write_dialogue_win(buf, DIAG_DEV_ROWS+2, 2); + write_dialogue_win(buf, diag_dev_rows() + 2, 2); handle_input_val(cdev_id); } else { snprintf(buf, sizeof(buf), "Invalid selection %d", ch); -- cgit v1.2.3-59-g8ed1b From 3dc3712a823dcedf0c3218aeb2b1e271439cae1b Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:33 -0800 Subject: tools/thermal: tmon: add .gitignore Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/.gitignore | 1 + 1 file changed, 1 insertion(+) create mode 100644 tools/thermal/tmon/.gitignore diff --git a/tools/thermal/tmon/.gitignore b/tools/thermal/tmon/.gitignore new file mode 100644 index 000000000000..06e96be65276 --- /dev/null +++ b/tools/thermal/tmon/.gitignore @@ -0,0 +1 @@ +/tmon -- cgit v1.2.3-59-g8ed1b From 1b0eaa2cc2dc52dced546c1c8b0551cfc734d32d Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:34 -0800 Subject: tools/thermal: tmon: support cross-compiling We might want to prepare CFLAGS outside of this Makefile, so don't overwrite its initial value. Then, support $(CROSS_COMPILE), so we can use a cross-compile toolchain. Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/Makefile | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/tools/thermal/tmon/Makefile b/tools/thermal/tmon/Makefile index e775adcbd29f..13d1876c7889 100644 --- a/tools/thermal/tmon/Makefile +++ b/tools/thermal/tmon/Makefile @@ -2,8 +2,8 @@ VERSION = 1.0 BINDIR=usr/bin WARNFLAGS=-Wall -Wshadow -W -Wformat -Wimplicit-function-declaration -Wimplicit-int -CFLAGS= -O1 ${WARNFLAGS} -fstack-protector -CC=gcc +CFLAGS+= -O1 ${WARNFLAGS} -fstack-protector +CC=$(CROSS_COMPILE)gcc CFLAGS+=-D VERSION=\"$(VERSION)\" LDFLAGS+= -- cgit v1.2.3-59-g8ed1b From 96a0d99c72cc4eb4f1b2acb71580693b91b95b28 Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:35 -0800 Subject: tools/thermal: tmon: use pkg-config to determine library dependencies Some distros (e.g., Arch Linux) don't package the tinfo library separately from ncurses, so don't unconditionally include it. Instead, use pkg-config. The $(STATIC) ugliness is to handle the reported build case from commit 6b533269fb25 ("tools/thermal: tmon: fix compilation errors when building statically"), where a developer wants to be able to build with: make LDFLAGS=-static which requires an additional pkg-config flag. Finally, support a lowest common denominator fallback (-lpanel -lncurses) for build systems that don't have pkg-config entries for ncurses. Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/Makefile | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/tools/thermal/tmon/Makefile b/tools/thermal/tmon/Makefile index 13d1876c7889..0788621c8d76 100644 --- a/tools/thermal/tmon/Makefile +++ b/tools/thermal/tmon/Makefile @@ -16,12 +16,21 @@ INSTALL_CONFIGFILE=install -m 644 -p CONFIG_FILE= CONFIG_PATH= +# Static builds might require -ltinfo, for instance +ifneq ($(findstring -static, $(LDFLAGS)),) +STATIC := --static +endif + +TMON_LIBS=-lm -lpthread +TMON_LIBS += $(shell pkg-config --libs $(STATIC) panelw ncursesw 2> /dev/null || \ + pkg-config --libs $(STATIC) panel ncurses 2> /dev/null || \ + echo -lpanel -lncurses) OBJS = tmon.o tui.o sysfs.o pid.o OBJS += tmon: $(OBJS) Makefile tmon.h - $(CC) ${CFLAGS} $(LDFLAGS) $(OBJS) -o $(TARGET) -lm -lpanel -lncursesw -ltinfo -lpthread + $(CC) $(CFLAGS) $(LDFLAGS) $(OBJS) -o $(TARGET) $(TMON_LIBS) valgrind: tmon sudo valgrind -v --track-origins=yes --tool=memcheck --leak-check=yes --show-reachable=yes --num-callers=20 --track-fds=yes ./$(TARGET) 1> /dev/null -- cgit v1.2.3-59-g8ed1b From 986ffe0384c38606b94947fad04e5deacb515408 Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 17 Feb 2015 18:18:36 -0800 Subject: tools/thermal: tmon: silence 'set but not used' warnings MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit gcc complains about the 'cols' variable being unused. This is unavoidable, given the ncurses getmaxyx() macro-based API, which wants to assign to a variable directly, even when we're not going to use it. Warning: gcc -O1 -Wall -Wshadow -W -Wformat -Wimplicit-function-declaration -Wimplicit-int -fstack-protector -D VERSION=\"1.0\" -c -o tui.o tui.c tui.c: In function ‘show_dialogue’: tui.c:288:12: warning: variable ‘cols’ set but not used [-Wunused-but-set-variable] int rows, cols; ^ So, add a hack to get rid of that warning. Signed-off-by: Brian Norris Acked-by: Jacob Pan Reviewed-by: Florian Fainelli Signed-off-by: Zhang Rui --- tools/thermal/tmon/tui.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/tools/thermal/tmon/tui.c b/tools/thermal/tmon/tui.c index 36e1f86c8452..b5d1c6b22dd3 100644 --- a/tools/thermal/tmon/tui.c +++ b/tools/thermal/tmon/tui.c @@ -293,6 +293,9 @@ void show_dialogue(void) getmaxyx(w, rows, cols); + /* Silence compiler 'unused' warnings */ + (void)cols; + werase(w); box(w, 0, 0); mvwprintw(w, 0, maxx/4, DIAG_TITLE); -- cgit v1.2.3-59-g8ed1b From 3a4562a02856ceca516bb61945aec3a83b8826db Mon Sep 17 00:00:00 2001 From: Miguel Bernal Marin Date: Thu, 19 Feb 2015 12:40:58 -0600 Subject: thermal/intel_powerclamp: add id for Avoton SoC Enable Intel Powerclamp driver on Atom* Processor C2000 Product Family for Microservers (Avoton). Avoton - SoCs for micro-servers has package C-states which can be used for idle injection. Reported-by: Jose Navarro Suggested-by: Jacob Pan Tested-by: Jose Carlos Venegas Munoz Signed-off-by: Miguel Bernal Marin Signed-off-by: Zhang Rui --- drivers/thermal/intel_powerclamp.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/thermal/intel_powerclamp.c b/drivers/thermal/intel_powerclamp.c index 6ceebd659dd4..12623bc02f46 100644 --- a/drivers/thermal/intel_powerclamp.c +++ b/drivers/thermal/intel_powerclamp.c @@ -688,6 +688,7 @@ static const struct x86_cpu_id intel_powerclamp_ids[] = { { X86_VENDOR_INTEL, 6, 0x45}, { X86_VENDOR_INTEL, 6, 0x46}, { X86_VENDOR_INTEL, 6, 0x4c}, + { X86_VENDOR_INTEL, 6, 0x4d}, { X86_VENDOR_INTEL, 6, 0x56}, {} }; -- cgit v1.2.3-59-g8ed1b From f126079123f9d055c2304b8ab17bac11b0cd22fa Mon Sep 17 00:00:00 2001 From: Srinivas Pandruvada Date: Wed, 25 Feb 2015 18:31:50 -0800 Subject: thermal: int340x_thermal: Ignore missing _ART, _TRT tables It is possible that _ART/_TRT tables are missing or have errors. Ignore those failures, as INT3400 thermal zone is still required for _OSC or mode switch. Signed-off-by: Srinivas Pandruvada Signed-off-by: Zhang Rui --- drivers/thermal/int340x_thermal/int3400_thermal.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) diff --git a/drivers/thermal/int340x_thermal/int3400_thermal.c b/drivers/thermal/int340x_thermal/int3400_thermal.c index 25d244cbbe8f..031018e7a65b 100644 --- a/drivers/thermal/int340x_thermal/int3400_thermal.c +++ b/drivers/thermal/int340x_thermal/int3400_thermal.c @@ -262,13 +262,12 @@ static int int3400_thermal_probe(struct platform_device *pdev) result = acpi_parse_art(priv->adev->handle, &priv->art_count, &priv->arts, true); if (result) - goto free_priv; - + dev_dbg(&pdev->dev, "_ART table parsing error\n"); result = acpi_parse_trt(priv->adev->handle, &priv->trt_count, &priv->trts, true); if (result) - goto free_art; + dev_dbg(&pdev->dev, "_TRT table parsing error\n"); platform_set_drvdata(pdev, priv); @@ -281,7 +280,7 @@ static int int3400_thermal_probe(struct platform_device *pdev) &int3400_thermal_params, 0, 0); if (IS_ERR(priv->thermal)) { result = PTR_ERR(priv->thermal); - goto free_trt; + goto free_art_trt; } priv->rel_misc_dev_res = acpi_thermal_rel_misc_device_add( @@ -295,9 +294,8 @@ static int int3400_thermal_probe(struct platform_device *pdev) free_zone: thermal_zone_device_unregister(priv->thermal); -free_trt: +free_art_trt: kfree(priv->trts); -free_art: kfree(priv->arts); free_priv: kfree(priv); -- cgit v1.2.3-59-g8ed1b From 5b2bdbc84556774afbe11bcfd24c2f6411cfa92b Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Fri, 27 Feb 2015 14:50:19 -0500 Subject: x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too Commit: 1e02ce4cccdc ("x86: Store a per-cpu shadow copy of CR4") added a shadow CR4 such that reads and writes that do not modify the CR4 execute much faster than always reading the register itself. The change modified cpu_init() in common.c, so that the shadow CR4 gets initialized before anything uses it. Unfortunately, there's two cpu_init()s in common.c. There's one for 64-bit and one for 32-bit. The commit only added the shadow init to the 64-bit path, but the 32-bit path needs the init too. Link: http://lkml.kernel.org/r/20150227125208.71c36402@gandalf.local.home Fixes: 1e02ce4cccdc "x86: Store a per-cpu shadow copy of CR4" Signed-off-by: Steven Rostedt Acked-by: Andy Lutomirski Cc: Peter Zijlstra (Intel) Cc: Linus Torvalds Link: http://lkml.kernel.org/r/20150227145019.2bdd4354@gandalf.local.home Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/common.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/x86/kernel/cpu/common.c b/arch/x86/kernel/cpu/common.c index b5c8ff5e9dfc..2346c95c6ab1 100644 --- a/arch/x86/kernel/cpu/common.c +++ b/arch/x86/kernel/cpu/common.c @@ -1396,6 +1396,12 @@ void cpu_init(void) wait_for_master_cpu(cpu); + /* + * Initialize the CR4 shadow before doing anything that could + * try to read it. + */ + cr4_init_shadow(); + show_ucode_info_early(); printk(KERN_INFO "Initializing CPU#%d\n", cpu); -- cgit v1.2.3-59-g8ed1b From 3608688973e8c85fbcd9b7e72b90e224b8d01526 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 28 Jan 2015 14:58:44 +0100 Subject: iio: ak8975: fix AK09911 dependencies ak8975 depends on I2C and GPIOLIB, so any symbols that selects ak8975 must have the same dependency, or we get build errors: drivers/iio/magnetometer/ak8975.c: In function 'ak8975_who_i_am': drivers/iio/magnetometer/ak8975.c:393:2: error: implicit declaration of function 'i2c_smbus_read_i2c_block_data' [-Werror=implicit-function-declaration] ret = i2c_smbus_read_i2c_block_data(client, AK09912_REG_WIA1, ^ drivers/iio/magnetometer/ak8975.c: In function 'ak8975_set_mode': drivers/iio/magnetometer/ak8975.c:431:2: error: implicit declaration of function 'i2c_smbus_write_byte_data' [-Werror=implicit-function-declaration] ret = i2c_smbus_write_byte_data(data->client, Signed-off-by: Arnd Bergmann Fixes: 57e73a423b1e85 ("iio: ak8975: add ak09911 and ak09912 support") Signed-off-by: Jonathan Cameron --- drivers/iio/magnetometer/Kconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/iio/magnetometer/Kconfig b/drivers/iio/magnetometer/Kconfig index 4c7a4c52dd06..a5d6de72c523 100644 --- a/drivers/iio/magnetometer/Kconfig +++ b/drivers/iio/magnetometer/Kconfig @@ -18,6 +18,8 @@ config AK8975 config AK09911 tristate "Asahi Kasei AK09911 3-axis Compass" + depends on I2C + depends on GPIOLIB select AK8975 help Deprecated: AK09911 is now supported by AK8975 driver. -- cgit v1.2.3-59-g8ed1b From 7e4f1e777814c6916b513b5dc90e030ee4e25f04 Mon Sep 17 00:00:00 2001 From: H Hartley Sweeten Date: Mon, 23 Feb 2015 13:22:44 -0700 Subject: staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample() The "stalled" variable this function is used to detect if the DMA operation is stalled while trying to disable DMA on a full comedi sample. The reset of this variable should only occur when the remaining bytes of the DMA transfer does not equal the remaining bytes from the last check. Reported-by: coverity (CID 1271132) Signed-off-by: H Hartley Sweeten Reviewed-by: Ian Abbott Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/staging/comedi/drivers/comedi_isadma.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/staging/comedi/drivers/comedi_isadma.c b/drivers/staging/comedi/drivers/comedi_isadma.c index dbdea71d6b95..e856f01ca077 100644 --- a/drivers/staging/comedi/drivers/comedi_isadma.c +++ b/drivers/staging/comedi/drivers/comedi_isadma.c @@ -91,9 +91,10 @@ unsigned int comedi_isadma_disable_on_sample(unsigned int dma_chan, stalled++; if (stalled > 10) break; + } else { + residue = new_residue; + stalled = 0; } - residue = new_residue; - stalled = 0; } return residue; } -- cgit v1.2.3-59-g8ed1b From 981c1fe9ae20e5fb7c1ee7038efa03933e637925 Mon Sep 17 00:00:00 2001 From: H Hartley Sweeten Date: Mon, 23 Feb 2015 15:13:49 -0700 Subject: staging: comedi: vmk80xx: remove "firmware version" kernel messages During the attach of this driver a couple commands are sent to the hardware with usb_bulk_msg() to read the firmware version information. This information is then dumped as dev_info() kernel messages. Thee messages are just added noise and don't effect the operation of the driver. For simplicity, remove the messages as well as the then unused functions vmk80xx_read_eeprom() and vmk80xx_check_data_link(). This also fixes an issue reported by coverity about an out-of-bounds write in vmk80xx_read_eeprom(). Reported-by: coverity (CID 711413) Signed-off-by: H Hartley Sweeten Reviewed-by: Ian Abbott Signed-off-by: Greg Kroah-Hartman --- drivers/staging/comedi/drivers/vmk80xx.c | 71 -------------------------------- 1 file changed, 71 deletions(-) diff --git a/drivers/staging/comedi/drivers/vmk80xx.c b/drivers/staging/comedi/drivers/vmk80xx.c index e37118321a27..a0906685e27f 100644 --- a/drivers/staging/comedi/drivers/vmk80xx.c +++ b/drivers/staging/comedi/drivers/vmk80xx.c @@ -103,11 +103,6 @@ enum vmk80xx_model { VMK8061_MODEL }; -struct firmware_version { - unsigned char ic3_vers[32]; /* USB-Controller */ - unsigned char ic6_vers[32]; /* CPU */ -}; - static const struct comedi_lrange vmk8061_range = { 2, { UNI_RANGE(5), @@ -156,68 +151,12 @@ static const struct vmk80xx_board vmk80xx_boardinfo[] = { struct vmk80xx_private { struct usb_endpoint_descriptor *ep_rx; struct usb_endpoint_descriptor *ep_tx; - struct firmware_version fw; struct semaphore limit_sem; unsigned char *usb_rx_buf; unsigned char *usb_tx_buf; enum vmk80xx_model model; }; -static int vmk80xx_check_data_link(struct comedi_device *dev) -{ - struct vmk80xx_private *devpriv = dev->private; - struct usb_device *usb = comedi_to_usb_dev(dev); - unsigned int tx_pipe; - unsigned int rx_pipe; - unsigned char tx[1]; - unsigned char rx[2]; - - tx_pipe = usb_sndbulkpipe(usb, 0x01); - rx_pipe = usb_rcvbulkpipe(usb, 0x81); - - tx[0] = VMK8061_CMD_RD_PWR_STAT; - - /* - * Check that IC6 (PIC16F871) is powered and - * running and the data link between IC3 and - * IC6 is working properly - */ - usb_bulk_msg(usb, tx_pipe, tx, 1, NULL, devpriv->ep_tx->bInterval); - usb_bulk_msg(usb, rx_pipe, rx, 2, NULL, HZ * 10); - - return (int)rx[1]; -} - -static void vmk80xx_read_eeprom(struct comedi_device *dev, int flag) -{ - struct vmk80xx_private *devpriv = dev->private; - struct usb_device *usb = comedi_to_usb_dev(dev); - unsigned int tx_pipe; - unsigned int rx_pipe; - unsigned char tx[1]; - unsigned char rx[64]; - int cnt; - - tx_pipe = usb_sndbulkpipe(usb, 0x01); - rx_pipe = usb_rcvbulkpipe(usb, 0x81); - - tx[0] = VMK8061_CMD_RD_VERSION; - - /* - * Read the firmware version info of IC3 and - * IC6 from the internal EEPROM of the IC - */ - usb_bulk_msg(usb, tx_pipe, tx, 1, NULL, devpriv->ep_tx->bInterval); - usb_bulk_msg(usb, rx_pipe, rx, 64, &cnt, HZ * 10); - - rx[cnt] = '\0'; - - if (flag & IC3_VERSION) - strncpy(devpriv->fw.ic3_vers, rx + 1, 24); - else /* IC6_VERSION */ - strncpy(devpriv->fw.ic6_vers, rx + 25, 24); -} - static void vmk80xx_do_bulk_msg(struct comedi_device *dev) { struct vmk80xx_private *devpriv = dev->private; @@ -878,16 +817,6 @@ static int vmk80xx_auto_attach(struct comedi_device *dev, usb_set_intfdata(intf, devpriv); - if (devpriv->model == VMK8061_MODEL) { - vmk80xx_read_eeprom(dev, IC3_VERSION); - dev_info(&intf->dev, "%s\n", devpriv->fw.ic3_vers); - - if (vmk80xx_check_data_link(dev)) { - vmk80xx_read_eeprom(dev, IC6_VERSION); - dev_info(&intf->dev, "%s\n", devpriv->fw.ic6_vers); - } - } - if (devpriv->model == VMK8055_MODEL) vmk80xx_reset_device(dev); -- cgit v1.2.3-59-g8ed1b From b70661c70830d5c69aab6844f2d86d2daf124fbd Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 25 Feb 2015 16:31:57 +0100 Subject: net: smc91x: use run-time configuration on all ARM machines The smc91x driver traditionally gets configured at compile-time for whichever hardware it runs on. This no longer works on ARM as we continue to move to building all-in-one kernels. Most ARM configurations with this driver already use run-time configuration through DT or through platform_data, but a few have not been converted yet. I've checked all ARM boards that use this driver in their legacy board files, and converted the ones that were using compile-time configuration in smc91x.h to behave like the other ones and provide the interrupt polarity along with the MMIO configuration (width, stride) at platform device creation time. In particular, these combinations were previously selectable in Kconfig but in fact broken: - sa1100 assabet plus pleb - msm combined with any other armv6/v7 platform - pxa-idp combined with any non-DMA pxa variant - LogicPD PXA270 combined with any other pxa - nomadik combined with any other armv4/v5 platform, e.g. versatile. None of these seem critical enough to warrant a backport to stable, but it would be nice to clean this up for good. Signed-off-by: Arnd Bergmann ---- I would like the patch to get merged through netdev, after Robert and/or Linus have verified it on at least some hardware. There are a few other non-ARM platforms using this driver, I could do the same patch for those if we want to take it further. arch/arm/mach-msm/board-halibut.c | 8 ++++- arch/arm/mach-msm/board-qsd8x50.c | 8 ++++- arch/arm/mach-pxa/idp.c | 5 +++ arch/arm/mach-pxa/lpd270.c | 8 ++++- arch/arm/mach-realview/core.c | 7 ++++ arch/arm/mach-realview/realview_eb.c | 2 +- arch/arm/mach-sa1100/neponset.c | 6 ++++ arch/arm/mach-sa1100/pleb.c | 7 ++++ drivers/net/ethernet/smsc/smc91x.c | 9 +++-- drivers/net/ethernet/smsc/smc91x.h | 114 ++---------------------------------------------------------- 10 files changed, 57 insertions(+), 117 deletions(-) Tested-by: Robert Jarzmik Signed-off-by: David S. Miller --- arch/arm/mach-msm/board-halibut.c | 8 ++- arch/arm/mach-msm/board-qsd8x50.c | 8 ++- arch/arm/mach-pxa/idp.c | 5 ++ arch/arm/mach-pxa/lpd270.c | 8 ++- arch/arm/mach-realview/core.c | 7 +++ arch/arm/mach-realview/realview_eb.c | 2 +- arch/arm/mach-sa1100/neponset.c | 6 ++ arch/arm/mach-sa1100/pleb.c | 7 +++ drivers/net/ethernet/smsc/smc91x.c | 9 ++- drivers/net/ethernet/smsc/smc91x.h | 114 +---------------------------------- 10 files changed, 57 insertions(+), 117 deletions(-) diff --git a/arch/arm/mach-msm/board-halibut.c b/arch/arm/mach-msm/board-halibut.c index 61bfe584a9d7..fc832040c6e9 100644 --- a/arch/arm/mach-msm/board-halibut.c +++ b/arch/arm/mach-msm/board-halibut.c @@ -20,6 +20,7 @@ #include #include #include +#include #include #include @@ -46,15 +47,20 @@ static struct resource smc91x_resources[] = { [1] = { .start = MSM_GPIO_TO_INT(49), .end = MSM_GPIO_TO_INT(49), - .flags = IORESOURCE_IRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, }, }; +static struct smc91x_platdata smc91x_platdata = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev.platform_data = &smc91x_platdata, }; static struct platform_device *devices[] __initdata = { diff --git a/arch/arm/mach-msm/board-qsd8x50.c b/arch/arm/mach-msm/board-qsd8x50.c index 4c748616ef47..10016a3bc698 100644 --- a/arch/arm/mach-msm/board-qsd8x50.c +++ b/arch/arm/mach-msm/board-qsd8x50.c @@ -22,6 +22,7 @@ #include #include #include +#include #include #include @@ -49,15 +50,20 @@ static struct resource smc91x_resources[] = { .flags = IORESOURCE_MEM, }, [1] = { - .flags = IORESOURCE_IRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, }, }; +static struct smc91x_platdata smc91x_platdata = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev.platform_data = &smc91x_platdata, }; static int __init msm_init_smc91x(void) diff --git a/arch/arm/mach-pxa/idp.c b/arch/arm/mach-pxa/idp.c index 343c4e3a7c5d..7d8eab857a93 100644 --- a/arch/arm/mach-pxa/idp.c +++ b/arch/arm/mach-pxa/idp.c @@ -81,11 +81,16 @@ static struct resource smc91x_resources[] = { } }; +static struct smc91x_platdata smc91x_platdata = { + .flags = SMC91X_USE_32BIT | SMC91X_USE_DMA | SMC91X_NOWAIT, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev.platform_data = &smc91x_platdata, }; static void idp_backlight_power(int on) diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c index ad777b353bd5..28da319d389f 100644 --- a/arch/arm/mach-pxa/lpd270.c +++ b/arch/arm/mach-pxa/lpd270.c @@ -24,6 +24,7 @@ #include #include #include +#include #include #include @@ -189,15 +190,20 @@ static struct resource smc91x_resources[] = { [1] = { .start = LPD270_ETHERNET_IRQ, .end = LPD270_ETHERNET_IRQ, - .flags = IORESOURCE_IRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, }, }; +struct smc91x_platdata smc91x_platdata = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT; +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev.platform_data = &smc91x_platdata, }; static struct resource lpd270_flash_resources[] = { diff --git a/arch/arm/mach-realview/core.c b/arch/arm/mach-realview/core.c index 850e506926df..c309593abdb2 100644 --- a/arch/arm/mach-realview/core.c +++ b/arch/arm/mach-realview/core.c @@ -28,6 +28,7 @@ #include #include #include +#include #include #include #include @@ -94,6 +95,10 @@ static struct smsc911x_platform_config smsc911x_config = { .phy_interface = PHY_INTERFACE_MODE_MII, }; +static struct smc91x_platdata smc91x_platdata = { + .flags = SMC91X_USE_32BIT | SMC91X_NOWAIT, +}; + static struct platform_device realview_eth_device = { .name = "smsc911x", .id = 0, @@ -107,6 +112,8 @@ int realview_eth_register(const char *name, struct resource *res) realview_eth_device.resource = res; if (strcmp(realview_eth_device.name, "smsc911x") == 0) realview_eth_device.dev.platform_data = &smsc911x_config; + else + realview_eth_device.dev.platform_data = &smc91x_platdata; return platform_device_register(&realview_eth_device); } diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index 64c88d657f9e..b3869cbbcc68 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -234,7 +234,7 @@ static struct resource realview_eb_eth_resources[] = { [1] = { .start = IRQ_EB_ETH, .end = IRQ_EB_ETH, - .flags = IORESOURCE_IRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, }, }; diff --git a/arch/arm/mach-sa1100/neponset.c b/arch/arm/mach-sa1100/neponset.c index 169262e3040d..7b0cd3172354 100644 --- a/arch/arm/mach-sa1100/neponset.c +++ b/arch/arm/mach-sa1100/neponset.c @@ -12,6 +12,7 @@ #include #include #include +#include #include #include @@ -258,12 +259,17 @@ static int neponset_probe(struct platform_device *dev) 0x02000000, "smc91x-attrib"), { .flags = IORESOURCE_IRQ }, }; + struct smc91x_platdata smc91x_platdata = { + .flags = SMC91X_USE_8BIT | SMC91X_IO_SHIFT_2 | SMC91X_NOWAIT, + }; struct platform_device_info smc91x_devinfo = { .parent = &dev->dev, .name = "smc91x", .id = 0, .res = smc91x_resources, .num_res = ARRAY_SIZE(smc91x_resources), + .data = &smc91c_platdata, + .size_data = sizeof(smc91c_platdata), }; int ret, irq; diff --git a/arch/arm/mach-sa1100/pleb.c b/arch/arm/mach-sa1100/pleb.c index 091261878eff..696fd0fe4806 100644 --- a/arch/arm/mach-sa1100/pleb.c +++ b/arch/arm/mach-sa1100/pleb.c @@ -11,6 +11,7 @@ #include #include #include +#include #include #include @@ -43,12 +44,18 @@ static struct resource smc91x_resources[] = { #endif }; +static struct smc91x_platdata smc91x_platdata = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, +}; static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev = { + .platform_data = &smc91c_platdata, + }, }; static struct platform_device *devices[] __initdata = { diff --git a/drivers/net/ethernet/smsc/smc91x.c b/drivers/net/ethernet/smsc/smc91x.c index fa3f193b5f4d..209ee1b27f8d 100644 --- a/drivers/net/ethernet/smsc/smc91x.c +++ b/drivers/net/ethernet/smsc/smc91x.c @@ -91,6 +91,10 @@ static const char version[] = #include "smc91x.h" +#if defined(CONFIG_ASSABET_NEPONSET) +#include +#endif + #ifndef SMC_NOWAIT # define SMC_NOWAIT 0 #endif @@ -2355,8 +2359,9 @@ static int smc_drv_probe(struct platform_device *pdev) ret = smc_request_attrib(pdev, ndev); if (ret) goto out_release_io; -#if defined(CONFIG_ASSABET_NEPONSET) && !defined(CONFIG_SA1100_PLEB) - neponset_ncr_set(NCR_ENET_OSC_EN); +#if defined(CONFIG_ASSABET_NEPONSET) + if (machine_is_assabet() && machine_has_neponset()) + neponset_ncr_set(NCR_ENET_OSC_EN); #endif platform_set_drvdata(pdev, ndev); ret = smc_enable_device(pdev); diff --git a/drivers/net/ethernet/smsc/smc91x.h b/drivers/net/ethernet/smsc/smc91x.h index be67baf5f677..3a18501d1068 100644 --- a/drivers/net/ethernet/smsc/smc91x.h +++ b/drivers/net/ethernet/smsc/smc91x.h @@ -39,14 +39,7 @@ * Define your architecture specific bus configuration parameters here. */ -#if defined(CONFIG_ARCH_LUBBOCK) ||\ - defined(CONFIG_MACH_MAINSTONE) ||\ - defined(CONFIG_MACH_ZYLONITE) ||\ - defined(CONFIG_MACH_LITTLETON) ||\ - defined(CONFIG_MACH_ZYLONITE2) ||\ - defined(CONFIG_ARCH_VIPER) ||\ - defined(CONFIG_MACH_STARGATE2) ||\ - defined(CONFIG_ARCH_VERSATILE) +#if defined(CONFIG_ARM) #include @@ -74,95 +67,8 @@ /* We actually can't write halfwords properly if not word aligned */ static inline void SMC_outw(u16 val, void __iomem *ioaddr, int reg) { - if ((machine_is_mainstone() || machine_is_stargate2()) && reg & 2) { - unsigned int v = val << 16; - v |= readl(ioaddr + (reg & ~2)) & 0xffff; - writel(v, ioaddr + (reg & ~2)); - } else { - writew(val, ioaddr + reg); - } -} - -#elif defined(CONFIG_SA1100_PLEB) -/* We can only do 16-bit reads and writes in the static memory space. */ -#define SMC_CAN_USE_8BIT 1 -#define SMC_CAN_USE_16BIT 1 -#define SMC_CAN_USE_32BIT 0 -#define SMC_IO_SHIFT 0 -#define SMC_NOWAIT 1 - -#define SMC_inb(a, r) readb((a) + (r)) -#define SMC_insb(a, r, p, l) readsb((a) + (r), p, (l)) -#define SMC_inw(a, r) readw((a) + (r)) -#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) -#define SMC_outb(v, a, r) writeb(v, (a) + (r)) -#define SMC_outsb(a, r, p, l) writesb((a) + (r), p, (l)) -#define SMC_outw(v, a, r) writew(v, (a) + (r)) -#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) - -#define SMC_IRQ_FLAGS (-1) - -#elif defined(CONFIG_SA1100_ASSABET) - -#include - -/* We can only do 8-bit reads and writes in the static memory space. */ -#define SMC_CAN_USE_8BIT 1 -#define SMC_CAN_USE_16BIT 0 -#define SMC_CAN_USE_32BIT 0 -#define SMC_NOWAIT 1 - -/* The first two address lines aren't connected... */ -#define SMC_IO_SHIFT 2 - -#define SMC_inb(a, r) readb((a) + (r)) -#define SMC_outb(v, a, r) writeb(v, (a) + (r)) -#define SMC_insb(a, r, p, l) readsb((a) + (r), p, (l)) -#define SMC_outsb(a, r, p, l) writesb((a) + (r), p, (l)) -#define SMC_IRQ_FLAGS (-1) /* from resource */ - -#elif defined(CONFIG_MACH_LOGICPD_PXA270) || \ - defined(CONFIG_MACH_NOMADIK_8815NHK) - -#define SMC_CAN_USE_8BIT 0 -#define SMC_CAN_USE_16BIT 1 -#define SMC_CAN_USE_32BIT 0 -#define SMC_IO_SHIFT 0 -#define SMC_NOWAIT 1 - -#define SMC_inw(a, r) readw((a) + (r)) -#define SMC_outw(v, a, r) writew(v, (a) + (r)) -#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) -#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) - -#elif defined(CONFIG_ARCH_INNOKOM) || \ - defined(CONFIG_ARCH_PXA_IDP) || \ - defined(CONFIG_ARCH_RAMSES) || \ - defined(CONFIG_ARCH_PCM027) - -#define SMC_CAN_USE_8BIT 1 -#define SMC_CAN_USE_16BIT 1 -#define SMC_CAN_USE_32BIT 1 -#define SMC_IO_SHIFT 0 -#define SMC_NOWAIT 1 -#define SMC_USE_PXA_DMA 1 - -#define SMC_inb(a, r) readb((a) + (r)) -#define SMC_inw(a, r) readw((a) + (r)) -#define SMC_inl(a, r) readl((a) + (r)) -#define SMC_outb(v, a, r) writeb(v, (a) + (r)) -#define SMC_outl(v, a, r) writel(v, (a) + (r)) -#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l) -#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l) -#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) -#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) -#define SMC_IRQ_FLAGS (-1) /* from resource */ - -/* We actually can't write halfwords properly if not word aligned */ -static inline void -SMC_outw(u16 val, void __iomem *ioaddr, int reg) -{ - if (reg & 2) { + if ((machine_is_mainstone() || machine_is_stargate2() || + machine_is_pxa_idp()) && reg & 2) { unsigned int v = val << 16; v |= readl(ioaddr + (reg & ~2)) & 0xffff; writel(v, ioaddr + (reg & ~2)); @@ -237,20 +143,6 @@ SMC_outw(u16 val, void __iomem *ioaddr, int reg) #define RPC_LSA_DEFAULT RPC_LED_100_10 #define RPC_LSB_DEFAULT RPC_LED_TX_RX -#elif defined(CONFIG_ARCH_MSM) - -#define SMC_CAN_USE_8BIT 0 -#define SMC_CAN_USE_16BIT 1 -#define SMC_CAN_USE_32BIT 0 -#define SMC_NOWAIT 1 - -#define SMC_inw(a, r) readw((a) + (r)) -#define SMC_outw(v, a, r) writew(v, (a) + (r)) -#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) -#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) - -#define SMC_IRQ_FLAGS IRQF_TRIGGER_HIGH - #elif defined(CONFIG_COLDFIRE) #define SMC_CAN_USE_8BIT 0 -- cgit v1.2.3-59-g8ed1b From 01945fa248ff6d34f5fdb8106118910b77b76f91 Mon Sep 17 00:00:00 2001 From: Mark Fasheh Date: Fri, 27 Feb 2015 15:51:40 -0800 Subject: ocfs2: update web page + git tree in documentation We (the Ocfs2 project) recently moved the location of our ocfs2-tools git tree and project web page. The pertinent discussion can be seen here: https://oss.oracle.com/pipermail/ocfs2-devel/2015-February/010579.html The following patch updates the Ocfs2 documentation in MAINTAINERS, ocfs2.txt, and dlmfs.txt. I added our new official web page, changed the location of our tools git tree and removed the link to Joel's ancient kernel git tree - Andrew has handled our patches for a while now. Signed-off-by: Mark Fasheh Cc: Joel Becker Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/filesystems/dlmfs.txt | 4 ++-- Documentation/filesystems/ocfs2.txt | 4 ++-- MAINTAINERS | 3 +-- 3 files changed, 5 insertions(+), 6 deletions(-) diff --git a/Documentation/filesystems/dlmfs.txt b/Documentation/filesystems/dlmfs.txt index 1b528b2ad809..fcf4d509d118 100644 --- a/Documentation/filesystems/dlmfs.txt +++ b/Documentation/filesystems/dlmfs.txt @@ -5,8 +5,8 @@ system. dlmfs is built with OCFS2 as it requires most of its infrastructure. -Project web page: http://oss.oracle.com/projects/ocfs2 -Tools web page: http://oss.oracle.com/projects/ocfs2-tools +Project web page: http://ocfs2.wiki.kernel.org +Tools web page: https://github.com/markfasheh/ocfs2-tools OCFS2 mailing lists: http://oss.oracle.com/projects/ocfs2/mailman/ All code copyright 2005 Oracle except when otherwise noted. diff --git a/Documentation/filesystems/ocfs2.txt b/Documentation/filesystems/ocfs2.txt index 28f8c08201e2..4c49e5410595 100644 --- a/Documentation/filesystems/ocfs2.txt +++ b/Documentation/filesystems/ocfs2.txt @@ -8,8 +8,8 @@ also make it attractive for non-clustered use. You'll want to install the ocfs2-tools package in order to at least get "mount.ocfs2" and "ocfs2_hb_ctl". -Project web page: http://oss.oracle.com/projects/ocfs2 -Tools web page: http://oss.oracle.com/projects/ocfs2-tools +Project web page: http://ocfs2.wiki.kernel.org +Tools git tree: https://github.com/markfasheh/ocfs2-tools OCFS2 mailing lists: http://oss.oracle.com/projects/ocfs2/mailman/ All code copyright 2005 Oracle except when otherwise noted. diff --git a/MAINTAINERS b/MAINTAINERS index ddc5a8cf9a8a..eaf999638a65 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7213,8 +7213,7 @@ ORACLE CLUSTER FILESYSTEM 2 (OCFS2) M: Mark Fasheh M: Joel Becker L: ocfs2-devel@oss.oracle.com (moderated for non-subscribers) -W: http://oss.oracle.com/projects/ocfs2/ -T: git git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2.git +W: http://ocfs2.wiki.kernel.org S: Supported F: Documentation/filesystems/ocfs2.txt F: Documentation/filesystems/dlmfs.txt -- cgit v1.2.3-59-g8ed1b From da616534ed7f6e8ffaab699258b55c8d78d0b4ea Mon Sep 17 00:00:00 2001 From: Joonsoo Kim Date: Fri, 27 Feb 2015 15:51:43 -0800 Subject: mm/nommu: fix memory leak Maxime reported the following memory leak regression due to commit dbc8358c7237 ("mm/nommu: use alloc_pages_exact() rather than its own implementation"). On v3.19, I am facing a memory leak. Each time I run a command one page is lost. Here an example with busybox's free command: / # free total used free shared buffers cached Mem: 7928 1972 5956 0 0 492 -/+ buffers/cache: 1480 6448 / # free total used free shared buffers cached Mem: 7928 1976 5952 0 0 492 -/+ buffers/cache: 1484 6444 / # free total used free shared buffers cached Mem: 7928 1980 5948 0 0 492 -/+ buffers/cache: 1488 6440 / # free total used free shared buffers cached Mem: 7928 1984 5944 0 0 492 -/+ buffers/cache: 1492 6436 / # free total used free shared buffers cached Mem: 7928 1988 5940 0 0 492 -/+ buffers/cache: 1496 6432 At some point, the system fails to sastisfy 256KB allocations: free: page allocation failure: order:6, mode:0xd0 CPU: 0 PID: 67 Comm: free Not tainted 3.19.0-05389-gacf2cf1-dirty #64 Hardware name: STM32 (Device Tree Support) show_stack+0xb/0xc warn_alloc_failed+0x97/0xbc __alloc_pages_nodemask+0x295/0x35c __get_free_pages+0xb/0x24 alloc_pages_exact+0x19/0x24 do_mmap_pgoff+0x423/0x658 vm_mmap_pgoff+0x3f/0x4e load_flat_file+0x20d/0x4f8 load_flat_binary+0x3f/0x26c search_binary_handler+0x51/0xe4 do_execveat_common+0x271/0x35c do_execve+0x19/0x1c ret_fast_syscall+0x1/0x4a Mem-info: Normal per-cpu: CPU 0: hi: 0, btch: 1 usd: 0 active_anon:0 inactive_anon:0 isolated_anon:0 active_file:0 inactive_file:0 isolated_file:0 unevictable:123 dirty:0 writeback:0 unstable:0 free:1515 slab_reclaimable:17 slab_unreclaimable:139 mapped:0 shmem:0 pagetables:0 bounce:0 free_cma:0 Normal free:6060kB min:352kB low:440kB high:528kB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:492kB isolated(anon):0ks lowmem_reserve[]: 0 0 Normal: 23*4kB (U) 22*8kB (U) 24*16kB (U) 23*32kB (U) 23*64kB (U) 23*128kB (U) 1*256kB (U) 0*512kB 0*1024kB 0*2048kB 0*4096kB = 6060kB 123 total pagecache pages 2048 pages of RAM 1538 free pages 66 reserved pages 109 slab pages -46 pages shared 0 pages swap cached nommu: Allocation of length 221184 from process 67 (free) failed Normal per-cpu: CPU 0: hi: 0, btch: 1 usd: 0 active_anon:0 inactive_anon:0 isolated_anon:0 active_file:0 inactive_file:0 isolated_file:0 unevictable:123 dirty:0 writeback:0 unstable:0 free:1515 slab_reclaimable:17 slab_unreclaimable:139 mapped:0 shmem:0 pagetables:0 bounce:0 free_cma:0 Normal free:6060kB min:352kB low:440kB high:528kB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:492kB isolated(anon):0ks lowmem_reserve[]: 0 0 Normal: 23*4kB (U) 22*8kB (U) 24*16kB (U) 23*32kB (U) 23*64kB (U) 23*128kB (U) 1*256kB (U) 0*512kB 0*1024kB 0*2048kB 0*4096kB = 6060kB 123 total pagecache pages Unable to allocate RAM for process text/data, errno 12 SEGV This problem happens because we allocate ordered page through __get_free_pages() in do_mmap_private() in some cases and we try to free individual pages rather than ordered page in free_page_series(). In this case, freeing pages whose refcount is not 0 won't be freed to the page allocator so memory leak happens. To fix the problem, this patch changes __get_free_pages() to alloc_pages_exact() since alloc_pages_exact() returns physically-contiguous pages but each pages are refcounted. Fixes: dbc8358c7237 ("mm/nommu: use alloc_pages_exact() rather than its own implementation"). Reported-by: Maxime Coquelin Tested-by: Maxime Coquelin Signed-off-by: Joonsoo Kim Cc: [3.19] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/nommu.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/mm/nommu.c b/mm/nommu.c index 7296360fc057..3e67e7538ecf 100644 --- a/mm/nommu.c +++ b/mm/nommu.c @@ -1213,11 +1213,9 @@ static int do_mmap_private(struct vm_area_struct *vma, if (sysctl_nr_trim_pages && total - point >= sysctl_nr_trim_pages) { total = point; kdebug("try to alloc exact %lu pages", total); - base = alloc_pages_exact(len, GFP_KERNEL); - } else { - base = (void *)__get_free_pages(GFP_KERNEL, order); } + base = alloc_pages_exact(total << PAGE_SHIFT, GFP_KERNEL); if (!base) goto enomem; -- cgit v1.2.3-59-g8ed1b From 4e54dede38b45052a941bcf709f7d29f2e18174d Mon Sep 17 00:00:00 2001 From: Michal Hocko Date: Fri, 27 Feb 2015 15:51:46 -0800 Subject: memcg: fix low limit calculation A memcg is considered low limited even when the current usage is equal to the low limit. This leads to interesting side effects e.g. groups/hierarchies with no memory accounted are considered protected and so the reclaim will emit MEMCG_LOW event when encountering them. Another and much bigger issue was reported by Joonsoo Kim. He has hit a NULL ptr dereference with the legacy cgroup API which even doesn't have low limit exposed. The limit is 0 by default but the initial check fails for memcg with 0 consumption and parent_mem_cgroup() would return NULL if use_hierarchy is 0 and so page_counter_read would try to dereference NULL. I suppose that the current implementation is just an overlook because the documentation in Documentation/cgroups/unified-hierarchy.txt says: "The memory.low boundary on the other hand is a top-down allocated reserve. A cgroup enjoys reclaim protection when it and all its ancestors are below their low boundaries" Fix the usage and the low limit comparision in mem_cgroup_low accordingly. Fixes: 241994ed8649 (mm: memcontrol: default hierarchy interface for memory) Reported-by: Joonsoo Kim Signed-off-by: Michal Hocko Acked-by: Johannes Weiner Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/memcontrol.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/mm/memcontrol.c b/mm/memcontrol.c index d18d3a6e7337..76c5a1b1dd21 100644 --- a/mm/memcontrol.c +++ b/mm/memcontrol.c @@ -5426,7 +5426,7 @@ bool mem_cgroup_low(struct mem_cgroup *root, struct mem_cgroup *memcg) if (memcg == root_mem_cgroup) return false; - if (page_counter_read(&memcg->memory) > memcg->low) + if (page_counter_read(&memcg->memory) >= memcg->low) return false; while (memcg != root) { @@ -5435,7 +5435,7 @@ bool mem_cgroup_low(struct mem_cgroup *root, struct mem_cgroup *memcg) if (memcg == root_mem_cgroup) break; - if (page_counter_read(&memcg->memory) > memcg->low) + if (page_counter_read(&memcg->memory) >= memcg->low) return false; } return true; -- cgit v1.2.3-59-g8ed1b From 682354d4e0bf9a28f11b52ef9be7fb38b901bd5c Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 27 Feb 2015 15:51:48 -0800 Subject: rtc: ds1685: fix ds1685_rtc_alarm_irq_enable build error The newly added ds1685 driver causes a build error when enabled without CONFIG_RTC_INTF_DEV: drivers/rtc/rtc-ds1685.c:919:22: error: 'ds1685_rtc_alarm_irq_enable' undeclared here (not in a function) .alarm_irq_enable = ds1685_rtc_alarm_irq_enable, Apparently the driver was incorrectly changed to reflect the interface change from 16380c153a69c ("RTC: Convert rtc drivers to use the alarm_irq_enable method"), which removed the respective #ifdef from all other rtc drivers. This does the same change that was merged for the other drivers before and removes the #ifdef, allowing the interrupts to be enabled through the in-kernel rtc interface independent of the existence of /dev/rtc. Fixes: aaaf5fbf56f ("rtc: add driver for DS1685 family of real time clocks") Signed-off-by: Arnd Bergmann Acked-by: Joshua Kinard Cc: Ralf Baechle Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-ds1685.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/rtc/rtc-ds1685.c b/drivers/rtc/rtc-ds1685.c index 8c3bfcb115b7..5dc1ef9d0008 100644 --- a/drivers/rtc/rtc-ds1685.c +++ b/drivers/rtc/rtc-ds1685.c @@ -528,7 +528,6 @@ ds1685_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) /* ----------------------------------------------------------------------- */ /* /dev/rtcX Interface functions */ -#ifdef CONFIG_RTC_INTF_DEV /** * ds1685_rtc_alarm_irq_enable - replaces ioctl() RTC_AIE on/off. * @dev: pointer to device structure. @@ -557,7 +556,6 @@ ds1685_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled) return 0; } -#endif /* ----------------------------------------------------------------------- */ -- cgit v1.2.3-59-g8ed1b From 39ea34cc07fb1ca8059239290967e006bbdacceb Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 27 Feb 2015 15:51:51 -0800 Subject: rtc: ds1685: remove superfluous checks for out-of-range u8 values drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_read_alarm': drivers/rtc/rtc-ds1685.c:402: warning: comparison is always true due to limited range of data type drivers/rtc/rtc-ds1685.c:409: warning: comparison is always true due to limited range of data type drivers/rtc/rtc-ds1685.c:416: warning: comparison is always true due to limited range of data type drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_set_alarm': drivers/rtc/rtc-ds1685.c:475: warning: comparison is always true due to limited range of data type drivers/rtc/rtc-ds1685.c:478: warning: comparison is always true due to limited range of data type drivers/rtc/rtc-ds1685.c:481: warning: comparison is always true due to limited range of data type u8 cannot contain a value larger than 0xff, hence drop the checks. Wrapping the checks in unlikely() indicated some sense of humor, though ;-) Signed-off-by: Geert Uytterhoeven Acked-by: Joshua Kinard Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-ds1685.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/rtc/rtc-ds1685.c b/drivers/rtc/rtc-ds1685.c index 5dc1ef9d0008..29b461c76072 100644 --- a/drivers/rtc/rtc-ds1685.c +++ b/drivers/rtc/rtc-ds1685.c @@ -399,21 +399,21 @@ ds1685_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm) * of this RTC chip. We check for it anyways in case support is * added in the future. */ - if (unlikely((seconds >= 0xc0) && (seconds <= 0xff))) + if (unlikely(seconds >= 0xc0)) alrm->time.tm_sec = -1; else alrm->time.tm_sec = ds1685_rtc_bcd2bin(rtc, seconds, RTC_SECS_BCD_MASK, RTC_SECS_BIN_MASK); - if (unlikely((minutes >= 0xc0) && (minutes <= 0xff))) + if (unlikely(minutes >= 0xc0)) alrm->time.tm_min = -1; else alrm->time.tm_min = ds1685_rtc_bcd2bin(rtc, minutes, RTC_MINS_BCD_MASK, RTC_MINS_BIN_MASK); - if (unlikely((hours >= 0xc0) && (hours <= 0xff))) + if (unlikely(hours >= 0xc0)) alrm->time.tm_hour = -1; else alrm->time.tm_hour = ds1685_rtc_bcd2bin(rtc, hours, @@ -472,13 +472,13 @@ ds1685_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) * field, and we only support four fields. We put the support * here anyways for the future. */ - if (unlikely((seconds >= 0xc0) && (seconds <= 0xff))) + if (unlikely(seconds >= 0xc0)) seconds = 0xff; - if (unlikely((minutes >= 0xc0) && (minutes <= 0xff))) + if (unlikely(minutes >= 0xc0)) minutes = 0xff; - if (unlikely((hours >= 0xc0) && (hours <= 0xff))) + if (unlikely(hours >= 0xc0)) hours = 0xff; alrm->time.tm_mon = -1; -- cgit v1.2.3-59-g8ed1b From 586a1a125eb157f0c2b9925ba878f24f4fe0c667 Mon Sep 17 00:00:00 2001 From: Jan Kiszka Date: Fri, 27 Feb 2015 15:51:53 -0800 Subject: scripts/gdb: add empty package initialization script This got lost during the initial merge process: Python requires an __init__.py script, even if empty, in order to accept a directory as package. Add it, this time as a non-empty file. Signed-off-by: Jan Kiszka Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- scripts/gdb/linux/__init__.py | 1 + 1 file changed, 1 insertion(+) create mode 100644 scripts/gdb/linux/__init__.py diff --git a/scripts/gdb/linux/__init__.py b/scripts/gdb/linux/__init__.py new file mode 100644 index 000000000000..4680fb176337 --- /dev/null +++ b/scripts/gdb/linux/__init__.py @@ -0,0 +1 @@ +# nothing to do for the initialization of this package -- cgit v1.2.3-59-g8ed1b From 957ed60b53b519064a54988c4e31e0087e47d091 Mon Sep 17 00:00:00 2001 From: Ryusuke Konishi Date: Fri, 27 Feb 2015 15:51:56 -0800 Subject: nilfs2: fix potential memory overrun on inode Each inode of nilfs2 stores a root node of a b-tree, and it turned out to have a memory overrun issue: Each b-tree node of nilfs2 stores a set of key-value pairs and the number of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as a few other "bn_*" members. Since the value of "bn_nchildren" is used for operations on the key-values within the b-tree node, it can cause memory access overrun if a large number is incorrectly set to "bn_nchildren". For instance, nilfs_btree_node_lookup() function determines the range of binary search with it, and too large "bn_nchildren" leads nilfs_btree_node_get_key() in that function to overrun. As for intermediate b-tree nodes, this is prevented by a sanity check performed when each node is read from a drive, however, no sanity check has been done for root nodes stored in inodes. This patch fixes the issue by adding missing sanity check against b-tree root nodes so that it's called when on-memory inodes are read from ifile, inode metadata file. Signed-off-by: Ryusuke Konishi Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/nilfs2/btree.c | 47 ++++++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 44 insertions(+), 3 deletions(-) diff --git a/fs/nilfs2/btree.c b/fs/nilfs2/btree.c index b2e3ff347620..ecdbae19a766 100644 --- a/fs/nilfs2/btree.c +++ b/fs/nilfs2/btree.c @@ -31,6 +31,8 @@ #include "alloc.h" #include "dat.h" +static void __nilfs_btree_init(struct nilfs_bmap *bmap); + static struct nilfs_btree_path *nilfs_btree_alloc_path(void) { struct nilfs_btree_path *path; @@ -368,6 +370,34 @@ static int nilfs_btree_node_broken(const struct nilfs_btree_node *node, return ret; } +/** + * nilfs_btree_root_broken - verify consistency of btree root node + * @node: btree root node to be examined + * @ino: inode number + * + * Return Value: If node is broken, 1 is returned. Otherwise, 0 is returned. + */ +static int nilfs_btree_root_broken(const struct nilfs_btree_node *node, + unsigned long ino) +{ + int level, flags, nchildren; + int ret = 0; + + level = nilfs_btree_node_get_level(node); + flags = nilfs_btree_node_get_flags(node); + nchildren = nilfs_btree_node_get_nchildren(node); + + if (unlikely(level < NILFS_BTREE_LEVEL_NODE_MIN || + level > NILFS_BTREE_LEVEL_MAX || + nchildren < 0 || + nchildren > NILFS_BTREE_ROOT_NCHILDREN_MAX)) { + pr_crit("NILFS: bad btree root (inode number=%lu): level = %d, flags = 0x%x, nchildren = %d\n", + ino, level, flags, nchildren); + ret = 1; + } + return ret; +} + int nilfs_btree_broken_node_block(struct buffer_head *bh) { int ret; @@ -1713,7 +1743,7 @@ nilfs_btree_commit_convert_and_insert(struct nilfs_bmap *btree, /* convert and insert */ dat = NILFS_BMAP_USE_VBN(btree) ? nilfs_bmap_get_dat(btree) : NULL; - nilfs_btree_init(btree); + __nilfs_btree_init(btree); if (nreq != NULL) { nilfs_bmap_commit_alloc_ptr(btree, dreq, dat); nilfs_bmap_commit_alloc_ptr(btree, nreq, dat); @@ -2294,12 +2324,23 @@ static const struct nilfs_bmap_operations nilfs_btree_ops_gc = { .bop_gather_data = NULL, }; -int nilfs_btree_init(struct nilfs_bmap *bmap) +static void __nilfs_btree_init(struct nilfs_bmap *bmap) { bmap->b_ops = &nilfs_btree_ops; bmap->b_nchildren_per_block = NILFS_BTREE_NODE_NCHILDREN_MAX(nilfs_btree_node_size(bmap)); - return 0; +} + +int nilfs_btree_init(struct nilfs_bmap *bmap) +{ + int ret = 0; + + __nilfs_btree_init(bmap); + + if (nilfs_btree_root_broken(nilfs_btree_get_root(bmap), + bmap->b_inode->i_ino)) + ret = -EIO; + return ret; } void nilfs_btree_init_gc(struct nilfs_bmap *bmap) -- cgit v1.2.3-59-g8ed1b From b00eeaedece2e8cb1607cb015f10e572e2607c49 Mon Sep 17 00:00:00 2001 From: Joshua Kinard Date: Fri, 27 Feb 2015 15:51:59 -0800 Subject: drivers/rtc/rtc-ds1685.c: fix conditional in ds1685_rtc_sysfs_time_regs_{show,store} Fix a conditional statement checking for NULL in both ds1685_rtc_sysfs_time_regs_show and ds1685_rtc_sysfs_time_regs_store that was using a logical AND when it should be using a logical OR so that we fail out of the function properly if the condition ever evaluates to true. Fixes: aaaf5fbf56f1 ("rtc: add driver for DS1685 family of real time clocks") Signed-off-by: Joshua Kinard Reported-by: Dan Carpenter Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-ds1685.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/rtc/rtc-ds1685.c b/drivers/rtc/rtc-ds1685.c index 29b461c76072..803869c7d7c2 100644 --- a/drivers/rtc/rtc-ds1685.c +++ b/drivers/rtc/rtc-ds1685.c @@ -1610,7 +1610,7 @@ ds1685_rtc_sysfs_time_regs_show(struct device *dev, ds1685_rtc_sysfs_time_regs_lookup(attr->attr.name, false); /* Make sure we actually matched something. */ - if (!bcd_reg_info && !bin_reg_info) + if (!bcd_reg_info || !bin_reg_info) return -EINVAL; /* bcd_reg_info->reg == bin_reg_info->reg. */ @@ -1648,7 +1648,7 @@ ds1685_rtc_sysfs_time_regs_store(struct device *dev, return -EINVAL; /* Make sure we actually matched something. */ - if (!bcd_reg_info && !bin_reg_info) + if (!bcd_reg_info || !bin_reg_info) return -EINVAL; /* Check for a valid range. */ -- cgit v1.2.3-59-g8ed1b From 2ea55a2caee016daee511431217861fb04767b27 Mon Sep 17 00:00:00 2001 From: Joonsoo Kim Date: Fri, 27 Feb 2015 15:52:01 -0800 Subject: zram: use proper type to update max_used_pages max_used_pages is defined as atomic_long_t so we need to use unsigned long to keep temporary value for it rather than int which is smaller than unsigned long in a 64 bit system. Signed-off-by: Joonsoo Kim Cc: Minchan Kim Cc: Jerome Marchand Cc: Nitin Gupta Cc: Sergey Senozhatsky Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/block/zram/zram_drv.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/block/zram/zram_drv.c b/drivers/block/zram/zram_drv.c index 8e233edd7a09..871bd3550cb0 100644 --- a/drivers/block/zram/zram_drv.c +++ b/drivers/block/zram/zram_drv.c @@ -528,7 +528,7 @@ out_cleanup: static inline void update_used_max(struct zram *zram, const unsigned long pages) { - int old_max, cur_max; + unsigned long old_max, cur_max; old_max = atomic_long_read(&zram->stats.max_used_pages); -- cgit v1.2.3-59-g8ed1b From d2973697b377e8b061e179c6057e94151759a73d Mon Sep 17 00:00:00 2001 From: Johannes Weiner Date: Fri, 27 Feb 2015 15:52:04 -0800 Subject: mm: memcontrol: use "max" instead of "infinity" in control knobs The memcg control knobs indicate the highest possible value using the symbolic name "infinity", which is long and awkward to type. Switch to the string "max", which is just as descriptive but shorter and sweeter. This changes a user interface, so do it before the release and before the development flag is dropped from the default hierarchy. Signed-off-by: Johannes Weiner Cc: Michal Hocko Cc: Tejun Heo Cc: Vladimir Davydov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/cgroups/unified-hierarchy.txt | 4 ++-- mm/memcontrol.c | 12 ++++++------ 2 files changed, 8 insertions(+), 8 deletions(-) diff --git a/Documentation/cgroups/unified-hierarchy.txt b/Documentation/cgroups/unified-hierarchy.txt index 71daa35ec2d9..eb102fb72213 100644 --- a/Documentation/cgroups/unified-hierarchy.txt +++ b/Documentation/cgroups/unified-hierarchy.txt @@ -404,8 +404,8 @@ supported and the interface files "release_agent" and be understood as an underflow into the highest possible value, -2 or -10M etc. do not work, so it's not consistent. - memory.low, memory.high, and memory.max will use the string - "infinity" to indicate and set the highest possible value. + memory.low, memory.high, and memory.max will use the string "max" to + indicate and set the highest possible value. 5. Planned Changes diff --git a/mm/memcontrol.c b/mm/memcontrol.c index 76c5a1b1dd21..9fe07692eaad 100644 --- a/mm/memcontrol.c +++ b/mm/memcontrol.c @@ -5247,7 +5247,7 @@ static int memory_low_show(struct seq_file *m, void *v) unsigned long low = ACCESS_ONCE(memcg->low); if (low == PAGE_COUNTER_MAX) - seq_puts(m, "infinity\n"); + seq_puts(m, "max\n"); else seq_printf(m, "%llu\n", (u64)low * PAGE_SIZE); @@ -5262,7 +5262,7 @@ static ssize_t memory_low_write(struct kernfs_open_file *of, int err; buf = strstrip(buf); - err = page_counter_memparse(buf, "infinity", &low); + err = page_counter_memparse(buf, "max", &low); if (err) return err; @@ -5277,7 +5277,7 @@ static int memory_high_show(struct seq_file *m, void *v) unsigned long high = ACCESS_ONCE(memcg->high); if (high == PAGE_COUNTER_MAX) - seq_puts(m, "infinity\n"); + seq_puts(m, "max\n"); else seq_printf(m, "%llu\n", (u64)high * PAGE_SIZE); @@ -5292,7 +5292,7 @@ static ssize_t memory_high_write(struct kernfs_open_file *of, int err; buf = strstrip(buf); - err = page_counter_memparse(buf, "infinity", &high); + err = page_counter_memparse(buf, "max", &high); if (err) return err; @@ -5307,7 +5307,7 @@ static int memory_max_show(struct seq_file *m, void *v) unsigned long max = ACCESS_ONCE(memcg->memory.limit); if (max == PAGE_COUNTER_MAX) - seq_puts(m, "infinity\n"); + seq_puts(m, "max\n"); else seq_printf(m, "%llu\n", (u64)max * PAGE_SIZE); @@ -5322,7 +5322,7 @@ static ssize_t memory_max_write(struct kernfs_open_file *of, int err; buf = strstrip(buf); - err = page_counter_memparse(buf, "infinity", &max); + err = page_counter_memparse(buf, "max", &max); if (err) return err; -- cgit v1.2.3-59-g8ed1b From 39afb5ee4640b4ed2cdd9e12b2a67cf785cfced8 Mon Sep 17 00:00:00 2001 From: Jon DeVree Date: Fri, 27 Feb 2015 15:52:07 -0800 Subject: kernel/sys.c: fix UNAME26 for 4.0 There's a uname workaround for broken userspace which can't handle kernel versions of 3.x. Update it for 4.x. Signed-off-by: Jon DeVree Cc: Andi Kleen Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/sys.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/sys.c b/kernel/sys.c index 667b2e62fad2..a03d9cd23ed7 100644 --- a/kernel/sys.c +++ b/kernel/sys.c @@ -1108,6 +1108,7 @@ DECLARE_RWSEM(uts_sem); /* * Work around broken programs that cannot handle "Linux 3.0". * Instead we map 3.x to 2.6.40+x, so e.g. 3.0 would be 2.6.40 + * And we map 4.x to 2.6.60+x, so 4.0 would be 2.6.60. */ static int override_release(char __user *release, size_t len) { @@ -1127,7 +1128,7 @@ static int override_release(char __user *release, size_t len) break; rest++; } - v = ((LINUX_VERSION_CODE >> 8) & 0xff) + 40; + v = ((LINUX_VERSION_CODE >> 8) & 0xff) + 60; copy = clamp_t(size_t, len, 1, sizeof(buf)); copy = scnprintf(buf, copy, "2.6.%u%s", v, rest); ret = copy_to_user(release, buf, copy + 1); -- cgit v1.2.3-59-g8ed1b From cc87317726f851531ae8422e0c2d3d6e2d7b1955 Mon Sep 17 00:00:00 2001 From: Johannes Weiner Date: Fri, 27 Feb 2015 15:52:09 -0800 Subject: mm: page_alloc: revert inadvertent !__GFP_FS retry behavior change Historically, !__GFP_FS allocations were not allowed to invoke the OOM killer once reclaim had failed, but nevertheless kept looping in the allocator. Commit 9879de7373fc ("mm: page_alloc: embed OOM killing naturally into allocation slowpath"), which should have been a simple cleanup patch, accidentally changed the behavior to aborting the allocation at that point. This creates problems with filesystem callers (?) that currently rely on the allocator waiting for other tasks to intervene. Revert the behavior as it shouldn't have been changed as part of a cleanup patch. Fixes: 9879de7373fc ("mm: page_alloc: embed OOM killing naturally into allocation slowpath") Signed-off-by: Johannes Weiner Acked-by: Michal Hocko Reported-by: Tetsuo Handa Cc: Theodore Ts'o Cc: Dave Chinner Acked-by: David Rientjes Cc: Oleg Nesterov Cc: Mel Gorman Cc: [3.19.x] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/page_alloc.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/mm/page_alloc.c b/mm/page_alloc.c index a47f0b229a1a..7abfa70cdc1a 100644 --- a/mm/page_alloc.c +++ b/mm/page_alloc.c @@ -2353,8 +2353,15 @@ __alloc_pages_may_oom(gfp_t gfp_mask, unsigned int order, if (ac->high_zoneidx < ZONE_NORMAL) goto out; /* The OOM killer does not compensate for light reclaim */ - if (!(gfp_mask & __GFP_FS)) + if (!(gfp_mask & __GFP_FS)) { + /* + * XXX: Page reclaim didn't yield anything, + * and the OOM killer can't be invoked, but + * keep looping as per should_alloc_retry(). + */ + *did_some_progress = 1; goto out; + } /* * GFP_THISNODE contains __GFP_NORETRY and we never hit this. * Sanity check for bare calls of __GFP_THISNODE, not real OOM. -- cgit v1.2.3-59-g8ed1b From c07af4f1ce413d009ea76ee69099f06f73ce75b2 Mon Sep 17 00:00:00 2001 From: "Kirill A. Shutemov" Date: Fri, 27 Feb 2015 15:52:12 -0800 Subject: mm: add missing __PAGETABLE_{PUD,PMD}_FOLDED defines Core mm expects __PAGETABLE_{PUD,PMD}_FOLDED to be defined if these page table levels folded. Usually, these defines are provided by and . But some architectures fold page table levels in a custom way. They need to define these macros themself. This patch adds missing defines. The patch fixes mm->nr_pmds underflow and eliminates dead __pmd_alloc() and __pud_alloc() on architectures without these page table levels. Signed-off-by: Kirill A. Shutemov Cc: Aaro Koskinen Cc: David Howells Cc: Geert Uytterhoeven Cc: Heiko Carstens Cc: Helge Deller Cc: "James E.J. Bottomley" Cc: Koichi Yasutake Cc: Martin Schwidefsky Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/frv/include/asm/pgtable.h | 2 ++ arch/m32r/include/asm/pgtable-2level.h | 1 + arch/m68k/include/asm/pgtable_mm.h | 2 ++ arch/mn10300/include/asm/pgtable.h | 2 ++ arch/parisc/include/asm/pgtable.h | 1 + arch/s390/include/asm/pgtable.h | 2 ++ 6 files changed, 10 insertions(+) diff --git a/arch/frv/include/asm/pgtable.h b/arch/frv/include/asm/pgtable.h index 93bcf2abd1a1..07d7a7ef8bd5 100644 --- a/arch/frv/include/asm/pgtable.h +++ b/arch/frv/include/asm/pgtable.h @@ -123,12 +123,14 @@ extern unsigned long empty_zero_page; #define PGDIR_MASK (~(PGDIR_SIZE - 1)) #define PTRS_PER_PGD 64 +#define __PAGETABLE_PUD_FOLDED #define PUD_SHIFT 26 #define PTRS_PER_PUD 1 #define PUD_SIZE (1UL << PUD_SHIFT) #define PUD_MASK (~(PUD_SIZE - 1)) #define PUE_SIZE 256 +#define __PAGETABLE_PMD_FOLDED #define PMD_SHIFT 26 #define PMD_SIZE (1UL << PMD_SHIFT) #define PMD_MASK (~(PMD_SIZE - 1)) diff --git a/arch/m32r/include/asm/pgtable-2level.h b/arch/m32r/include/asm/pgtable-2level.h index 8fd8ee70266a..421e6ba3a173 100644 --- a/arch/m32r/include/asm/pgtable-2level.h +++ b/arch/m32r/include/asm/pgtable-2level.h @@ -13,6 +13,7 @@ * the M32R is two-level, so we don't really have any * PMD directory physically. */ +#define __PAGETABLE_PMD_FOLDED #define PMD_SHIFT 22 #define PTRS_PER_PMD 1 diff --git a/arch/m68k/include/asm/pgtable_mm.h b/arch/m68k/include/asm/pgtable_mm.h index 28a145bfbb71..35ed4a9981ae 100644 --- a/arch/m68k/include/asm/pgtable_mm.h +++ b/arch/m68k/include/asm/pgtable_mm.h @@ -54,10 +54,12 @@ */ #ifdef CONFIG_SUN3 #define PTRS_PER_PTE 16 +#define __PAGETABLE_PMD_FOLDED #define PTRS_PER_PMD 1 #define PTRS_PER_PGD 2048 #elif defined(CONFIG_COLDFIRE) #define PTRS_PER_PTE 512 +#define __PAGETABLE_PMD_FOLDED #define PTRS_PER_PMD 1 #define PTRS_PER_PGD 1024 #else diff --git a/arch/mn10300/include/asm/pgtable.h b/arch/mn10300/include/asm/pgtable.h index afab728ab65e..96d3f9deb59c 100644 --- a/arch/mn10300/include/asm/pgtable.h +++ b/arch/mn10300/include/asm/pgtable.h @@ -56,7 +56,9 @@ extern void paging_init(void); #define PGDIR_SHIFT 22 #define PTRS_PER_PGD 1024 #define PTRS_PER_PUD 1 /* we don't really have any PUD physically */ +#define __PAGETABLE_PUD_FOLDED #define PTRS_PER_PMD 1 /* we don't really have any PMD physically */ +#define __PAGETABLE_PMD_FOLDED #define PTRS_PER_PTE 1024 #define PGD_SIZE PAGE_SIZE diff --git a/arch/parisc/include/asm/pgtable.h b/arch/parisc/include/asm/pgtable.h index 8c966b2270aa..15207b9362bf 100644 --- a/arch/parisc/include/asm/pgtable.h +++ b/arch/parisc/include/asm/pgtable.h @@ -96,6 +96,7 @@ extern void purge_tlb_entries(struct mm_struct *, unsigned long); #if PT_NLEVELS == 3 #define BITS_PER_PMD (PAGE_SHIFT + PMD_ORDER - BITS_PER_PMD_ENTRY) #else +#define __PAGETABLE_PMD_FOLDED #define BITS_PER_PMD 0 #endif #define PTRS_PER_PMD (1UL << BITS_PER_PMD) diff --git a/arch/s390/include/asm/pgtable.h b/arch/s390/include/asm/pgtable.h index fbb5ee3ae57c..e08ec38f8c6e 100644 --- a/arch/s390/include/asm/pgtable.h +++ b/arch/s390/include/asm/pgtable.h @@ -91,7 +91,9 @@ extern unsigned long zero_page_mask; */ #define PTRS_PER_PTE 256 #ifndef CONFIG_64BIT +#define __PAGETABLE_PUD_FOLDED #define PTRS_PER_PMD 1 +#define __PAGETABLE_PMD_FOLDED #define PTRS_PER_PUD 1 #else /* CONFIG_64BIT */ #define PTRS_PER_PMD 2048 -- cgit v1.2.3-59-g8ed1b From f55ea3d932df06d82f37de5826063caf938c06f2 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Thu, 26 Feb 2015 19:56:56 +0300 Subject: niu: fix error handling in niu_class_to_ethflow() There is a discrepancy here because the niu_class_to_ethflow() returns zero on failure and one on success but the caller expected zero on success and negative on failure. The problem means that we allow the user to pass classes and flow_types which we don't want. I've looked at it a bit and I don't see it as a very serious bug. Signed-off-by: Dan Carpenter Signed-off-by: David S. Miller --- drivers/net/ethernet/sun/niu.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/drivers/net/ethernet/sun/niu.c b/drivers/net/ethernet/sun/niu.c index 4b51f903fb73..0c5842aeb807 100644 --- a/drivers/net/ethernet/sun/niu.c +++ b/drivers/net/ethernet/sun/niu.c @@ -6989,10 +6989,10 @@ static int niu_class_to_ethflow(u64 class, int *flow_type) *flow_type = IP_USER_FLOW; break; default: - return 0; + return -EINVAL; } - return 1; + return 0; } static int niu_ethflow_to_class(int flow_type, u64 *class) @@ -7198,11 +7198,9 @@ static int niu_get_ethtool_tcam_entry(struct niu *np, class = (tp->key[0] & TCAM_V4KEY0_CLASS_CODE) >> TCAM_V4KEY0_CLASS_CODE_SHIFT; ret = niu_class_to_ethflow(class, &fsp->flow_type); - if (ret < 0) { netdev_info(np->dev, "niu%d: niu_class_to_ethflow failed\n", parent->index); - ret = -EINVAL; goto out; } -- cgit v1.2.3-59-g8ed1b From 5688714977ebefa92e6dad8bd94bffaeaadc303d Mon Sep 17 00:00:00 2001 From: George McCollister Date: Thu, 26 Feb 2015 15:19:30 -0600 Subject: drivers: net: cpsw: Set SECURE for dual_emac ucast Prior to this patch, sending a packet with the source MAC address of one of the CPSW interfaces to one of the CPSW slave ports while it's configured in dual_emac mode would update the port_num field of the VLAN/Unicast Address Table Entry. This would cause it to discard all incoming traffic addressed to that MAC address, essentially rendering the port useless until the ALE table is cleared (by starting and stopping the interface or rebooting.) For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have an ALE table entry: 00 00 00 00 59 90 02 30 e9 43 8f af (VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9) If you configure another device with the same MAC address and connect it to the first CPSW slave port and send some traffic the ALE table entry becomes: 04 00 00 00 59 90 02 30 e9 43 8f af (VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9) >From this point forward all incoming traffic addressed to 90:59:af:8f:43:e9 will be dropped. Setting the SECURE bit for the VLAN/Unicast address table entry for each interface's MAC address corrects the problem. Signed-off-by: George McCollister Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 7d8dd0d2182e..49b03368f4b9 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -1103,7 +1103,7 @@ static inline void cpsw_add_dual_emac_def_ale_entries( cpsw_ale_add_mcast(priv->ale, priv->ndev->broadcast, port_mask, ALE_VLAN, slave->port_vlan, 0); cpsw_ale_add_ucast(priv->ale, priv->mac_addr, - priv->host_port, ALE_VLAN, slave->port_vlan); + priv->host_port, ALE_VLAN | ALE_SECURE, slave->port_vlan); } static void soft_reset_slave(struct cpsw_slave *slave) -- cgit v1.2.3-59-g8ed1b From 505ce4154ac86c250aa4a84a536dd9fc56479bb5 Mon Sep 17 00:00:00 2001 From: "Eric W. Biederman" Date: Thu, 26 Feb 2015 16:19:00 -0600 Subject: net: Verify permission to dest_net in newlink When applicable verify that the caller has permision to create a network device in another network namespace. This check is already present when moving a network device between network namespaces in setlink so all that is needed is to duplicate that check in newlink. This change almost backports cleanly, but there are context conflicts as the code that follows was added in v4.0-rc1 Fixes: b51642f6d77b net: Enable a userns root rtnl calls that are safe for unprivilged users Signed-off-by: "Eric W. Biederman" Acked-by: Nicolas Dichtel Signed-off-by: David S. Miller --- net/core/rtnetlink.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/net/core/rtnetlink.c b/net/core/rtnetlink.c index 1385de0fa080..b237959c7497 100644 --- a/net/core/rtnetlink.c +++ b/net/core/rtnetlink.c @@ -2122,6 +2122,10 @@ replay: if (IS_ERR(dest_net)) return PTR_ERR(dest_net); + err = -EPERM; + if (!netlink_ns_capable(skb, dest_net->user_ns, CAP_NET_ADMIN)) + goto out; + if (tb[IFLA_LINK_NETNSID]) { int id = nla_get_s32(tb[IFLA_LINK_NETNSID]); -- cgit v1.2.3-59-g8ed1b From 06615bed60c1fb7c37adddb75bdc80da873b5edb Mon Sep 17 00:00:00 2001 From: "Eric W. Biederman" Date: Thu, 26 Feb 2015 16:20:07 -0600 Subject: net: Verify permission to link_net in newlink When applicable verify that the caller has permisson to the underlying network namespace for a newly created network device. Similary checks exist for the network namespace a network device will be created in. Fixes: 317f4810e45e ("rtnl: allow to create device with IFLA_LINK_NETNSID set") Signed-off-by: "Eric W. Biederman" Acked-by: Nicolas Dichtel Signed-off-by: David S. Miller --- net/core/rtnetlink.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/net/core/rtnetlink.c b/net/core/rtnetlink.c index b237959c7497..2c49355d16c2 100644 --- a/net/core/rtnetlink.c +++ b/net/core/rtnetlink.c @@ -2134,6 +2134,9 @@ replay: err = -EINVAL; goto out; } + err = -EPERM; + if (!netlink_ns_capable(skb, link_net->user_ns, CAP_NET_ADMIN)) + goto out; } dev = rtnl_create_link(link_net ? : dest_net, ifname, -- cgit v1.2.3-59-g8ed1b From 01e04f466e12e883907937eb04a9010533363f55 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Fri, 27 Feb 2015 00:39:21 +0100 Subject: idle / sleep: Avoid excessive disabling and enabling interrupts Disabling interrupts at the end of cpuidle_enter_freeze() is not useful, because its caller, cpuidle_idle_call(), re-enables them right away after invoking it. To avoid that unnecessary back and forth dance with interrupts, make cpuidle_enter_freeze() enable interrupts after calling enter_freeze_proper() and drop the local_irq_disable() at its end, so that all of the code paths in it end up with interrupts enabled. Then, cpuidle_idle_call() will not need to re-enable interrupts after calling cpuidle_enter_freeze() any more, because the latter will return with interrupts enabled, in analogy with cpuidle_enter(). Reported-by: Lorenzo Pieralisi Signed-off-by: Rafael J. Wysocki Acked-by: Peter Zijlstra (Intel) --- drivers/cpuidle/cpuidle.c | 6 +++--- kernel/sched/idle.c | 1 - 2 files changed, 3 insertions(+), 4 deletions(-) diff --git a/drivers/cpuidle/cpuidle.c b/drivers/cpuidle/cpuidle.c index 4d534582514e..b573f584b15a 100644 --- a/drivers/cpuidle/cpuidle.c +++ b/drivers/cpuidle/cpuidle.c @@ -117,6 +117,8 @@ static void enter_freeze_proper(struct cpuidle_driver *drv, * If there are states with the ->enter_freeze callback, find the deepest of * them and enter it with frozen tick. Otherwise, find the deepest state * available and enter it normally. + * + * Returns with enabled interrupts. */ void cpuidle_enter_freeze(void) { @@ -132,6 +134,7 @@ void cpuidle_enter_freeze(void) index = cpuidle_find_deepest_state(drv, dev, true); if (index >= 0) { enter_freeze_proper(drv, dev, index); + local_irq_enable(); return; } @@ -144,9 +147,6 @@ void cpuidle_enter_freeze(void) cpuidle_enter(drv, dev, index); else arch_cpu_idle(); - - /* Interrupts are enabled again here. */ - local_irq_disable(); } /** diff --git a/kernel/sched/idle.c b/kernel/sched/idle.c index 94b2d7b88a27..f59198bda1bf 100644 --- a/kernel/sched/idle.c +++ b/kernel/sched/idle.c @@ -116,7 +116,6 @@ static void cpuidle_idle_call(void) */ if (idle_should_freeze()) { cpuidle_enter_freeze(); - local_irq_enable(); goto exit_idle; } -- cgit v1.2.3-59-g8ed1b From 31a3409065d1d5bf0f12ad76b8c7f471134bf596 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Fri, 27 Feb 2015 00:39:56 +0100 Subject: cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too Modify cpuidle_enter_freeze() to do the sanity checks done by cpuidle_select() to avoid crashing the suspend-to-idle code path in case something is missing. Fixes: 381063133246 (PM / sleep: Re-implement suspend-to-idle handling) Original-by: Lorenzo Pieralisi Signed-off-by: Rafael J. Wysocki Acked-by: Peter Zijlstra (Intel) --- drivers/cpuidle/cpuidle.c | 23 ++++++++++++++++------- 1 file changed, 16 insertions(+), 7 deletions(-) diff --git a/drivers/cpuidle/cpuidle.c b/drivers/cpuidle/cpuidle.c index b573f584b15a..8b3e132b6a01 100644 --- a/drivers/cpuidle/cpuidle.c +++ b/drivers/cpuidle/cpuidle.c @@ -44,6 +44,12 @@ void disable_cpuidle(void) off = 1; } +static bool cpuidle_not_available(struct cpuidle_driver *drv, + struct cpuidle_device *dev) +{ + return off || !initialized || !drv || !dev || !dev->enabled; +} + /** * cpuidle_play_dead - cpu off-lining * @@ -126,6 +132,9 @@ void cpuidle_enter_freeze(void) struct cpuidle_driver *drv = cpuidle_get_cpu_driver(dev); int index; + if (cpuidle_not_available(drv, dev)) + goto fallback; + /* * Find the deepest state with ->enter_freeze present, which guarantees * that interrupts won't be enabled when it exits and allows the tick to @@ -143,10 +152,13 @@ void cpuidle_enter_freeze(void) * at all and try to enter it normally. */ index = cpuidle_find_deepest_state(drv, dev, false); - if (index >= 0) + if (index >= 0) { cpuidle_enter(drv, dev, index); - else - arch_cpu_idle(); + return; + } + + fallback: + arch_cpu_idle(); } /** @@ -205,12 +217,9 @@ int cpuidle_enter_state(struct cpuidle_device *dev, struct cpuidle_driver *drv, */ int cpuidle_select(struct cpuidle_driver *drv, struct cpuidle_device *dev) { - if (off || !initialized) + if (cpuidle_not_available(drv, dev)) return -ENODEV; - if (!drv || !dev || !dev->enabled) - return -EBUSY; - return cpuidle_curr_governor->select(drv, dev); } -- cgit v1.2.3-59-g8ed1b From 2f1d8b9e8afa5a833d96afcd23abcb8cdf8d83ab Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 27 Feb 2015 18:35:35 -0800 Subject: macvtap: make sure neighbour code can push ethernet header Brian reported crashes using IPv6 traffic with macvtap/veth combo. I tracked the crashes in neigh_hh_output() -> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD); Neighbour code assumes headroom to push Ethernet header is at least 16 bytes. It appears macvtap has only 14 bytes available on arches where NET_IP_ALIGN is 0 (like x86) Effect is a corruption of 2 bytes right before skb->head, and possible crashes if accessing non existing memory. This fix should also increase IPv4 performance, as paranoid code in ip_finish_output2() wont have to call skb_realloc_headroom() Reported-by: Brian Rak Tested-by: Brian Rak Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/macvtap.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/drivers/net/macvtap.c b/drivers/net/macvtap.c index e40fdfccc9c1..27ecc5c4fa26 100644 --- a/drivers/net/macvtap.c +++ b/drivers/net/macvtap.c @@ -654,11 +654,14 @@ static void macvtap_skb_to_vnet_hdr(struct macvtap_queue *q, } /* else everything is zero */ } +/* Neighbour code has some assumptions on HH_DATA_MOD alignment */ +#define MACVTAP_RESERVE HH_DATA_OFF(ETH_HLEN) + /* Get packet from user space buffer */ static ssize_t macvtap_get_user(struct macvtap_queue *q, struct msghdr *m, struct iov_iter *from, int noblock) { - int good_linear = SKB_MAX_HEAD(NET_IP_ALIGN); + int good_linear = SKB_MAX_HEAD(MACVTAP_RESERVE); struct sk_buff *skb; struct macvlan_dev *vlan; unsigned long total_len = iov_iter_count(from); @@ -722,7 +725,7 @@ static ssize_t macvtap_get_user(struct macvtap_queue *q, struct msghdr *m, linear = macvtap16_to_cpu(q, vnet_hdr.hdr_len); } - skb = macvtap_alloc_skb(&q->sk, NET_IP_ALIGN, copylen, + skb = macvtap_alloc_skb(&q->sk, MACVTAP_RESERVE, copylen, linear, noblock, &err); if (!skb) goto err; -- cgit v1.2.3-59-g8ed1b From 4092e6acf5cb16f56154e2dd22d647023dc3d646 Mon Sep 17 00:00:00 2001 From: Jaedon Shin Date: Sat, 28 Feb 2015 11:48:26 +0900 Subject: net: bcmgenet: fix throughtput regression This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the interrupt load and send xmit in network stack on time. This also separated for the completion of tx_ring16 from bcmgenet_poll. The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt is to be not more than a certain number TxBDs. It is caused by too slowly reclaiming the transmitted skb. Therefore, performance degradation of xmit after 605ad7f ("tcp: refine TSO autosizing"). Signed-off-by: Jaedon Shin Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/genet/bcmgenet.c | 113 +++++++++++++++++++------ drivers/net/ethernet/broadcom/genet/bcmgenet.h | 2 + 2 files changed, 88 insertions(+), 27 deletions(-) diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c index ff83c46bc389..2874a004f815 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c @@ -971,13 +971,14 @@ static inline void bcmgenet_tx_ring_int_disable(struct bcmgenet_priv *priv, } /* Unlocked version of the reclaim routine */ -static void __bcmgenet_tx_reclaim(struct net_device *dev, - struct bcmgenet_tx_ring *ring) +static unsigned int __bcmgenet_tx_reclaim(struct net_device *dev, + struct bcmgenet_tx_ring *ring) { struct bcmgenet_priv *priv = netdev_priv(dev); int last_tx_cn, last_c_index, num_tx_bds; struct enet_cb *tx_cb_ptr; struct netdev_queue *txq; + unsigned int pkts_compl = 0; unsigned int bds_compl; unsigned int c_index; @@ -1005,6 +1006,7 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, tx_cb_ptr = ring->cbs + last_c_index; bds_compl = 0; if (tx_cb_ptr->skb) { + pkts_compl++; bds_compl = skb_shinfo(tx_cb_ptr->skb)->nr_frags + 1; dev->stats.tx_bytes += tx_cb_ptr->skb->len; dma_unmap_single(&dev->dev, @@ -1028,23 +1030,45 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, last_c_index &= (num_tx_bds - 1); } - if (ring->free_bds > (MAX_SKB_FRAGS + 1)) - ring->int_disable(priv, ring); - - if (netif_tx_queue_stopped(txq)) - netif_tx_wake_queue(txq); + if (ring->free_bds > (MAX_SKB_FRAGS + 1)) { + if (netif_tx_queue_stopped(txq)) + netif_tx_wake_queue(txq); + } ring->c_index = c_index; + + return pkts_compl; } -static void bcmgenet_tx_reclaim(struct net_device *dev, +static unsigned int bcmgenet_tx_reclaim(struct net_device *dev, struct bcmgenet_tx_ring *ring) { + unsigned int released; unsigned long flags; spin_lock_irqsave(&ring->lock, flags); - __bcmgenet_tx_reclaim(dev, ring); + released = __bcmgenet_tx_reclaim(dev, ring); spin_unlock_irqrestore(&ring->lock, flags); + + return released; +} + +static int bcmgenet_tx_poll(struct napi_struct *napi, int budget) +{ + struct bcmgenet_tx_ring *ring = + container_of(napi, struct bcmgenet_tx_ring, napi); + unsigned int work_done = 0; + + work_done = bcmgenet_tx_reclaim(ring->priv->dev, ring); + + if (work_done == 0) { + napi_complete(napi); + ring->int_enable(ring->priv, ring); + + return 0; + } + + return budget; } static void bcmgenet_tx_reclaim_all(struct net_device *dev) @@ -1302,10 +1326,8 @@ static netdev_tx_t bcmgenet_xmit(struct sk_buff *skb, struct net_device *dev) bcmgenet_tdma_ring_writel(priv, ring->index, ring->prod_index, TDMA_PROD_INDEX); - if (ring->free_bds <= (MAX_SKB_FRAGS + 1)) { + if (ring->free_bds <= (MAX_SKB_FRAGS + 1)) netif_tx_stop_queue(txq); - ring->int_enable(priv, ring); - } out: spin_unlock_irqrestore(&ring->lock, flags); @@ -1621,6 +1643,7 @@ static int init_umac(struct bcmgenet_priv *priv) struct device *kdev = &priv->pdev->dev; int ret; u32 reg, cpu_mask_clear; + int index; dev_dbg(&priv->pdev->dev, "bcmgenet: init_umac\n"); @@ -1647,7 +1670,7 @@ static int init_umac(struct bcmgenet_priv *priv) bcmgenet_intr_disable(priv); - cpu_mask_clear = UMAC_IRQ_RXDMA_BDONE; + cpu_mask_clear = UMAC_IRQ_RXDMA_BDONE | UMAC_IRQ_TXDMA_BDONE; dev_dbg(kdev, "%s:Enabling RXDMA_BDONE interrupt\n", __func__); @@ -1674,6 +1697,10 @@ static int init_umac(struct bcmgenet_priv *priv) bcmgenet_intrl2_0_writel(priv, cpu_mask_clear, INTRL2_CPU_MASK_CLEAR); + for (index = 0; index < priv->hw_params->tx_queues; index++) + bcmgenet_intrl2_1_writel(priv, (1 << index), + INTRL2_CPU_MASK_CLEAR); + /* Enable rx/tx engine.*/ dev_dbg(kdev, "done init umac\n"); @@ -1693,6 +1720,8 @@ static void bcmgenet_init_tx_ring(struct bcmgenet_priv *priv, unsigned int first_bd; spin_lock_init(&ring->lock); + ring->priv = priv; + netif_napi_add(priv->dev, &ring->napi, bcmgenet_tx_poll, 64); ring->index = index; if (index == DESC_INDEX) { ring->queue = 0; @@ -1738,6 +1767,17 @@ static void bcmgenet_init_tx_ring(struct bcmgenet_priv *priv, TDMA_WRITE_PTR); bcmgenet_tdma_ring_writel(priv, index, end_ptr * words_per_bd - 1, DMA_END_ADDR); + + napi_enable(&ring->napi); +} + +static void bcmgenet_fini_tx_ring(struct bcmgenet_priv *priv, + unsigned int index) +{ + struct bcmgenet_tx_ring *ring = &priv->tx_rings[index]; + + napi_disable(&ring->napi); + netif_napi_del(&ring->napi); } /* Initialize a RDMA ring */ @@ -1907,7 +1947,7 @@ static int bcmgenet_dma_teardown(struct bcmgenet_priv *priv) return ret; } -static void bcmgenet_fini_dma(struct bcmgenet_priv *priv) +static void __bcmgenet_fini_dma(struct bcmgenet_priv *priv) { int i; @@ -1926,6 +1966,18 @@ static void bcmgenet_fini_dma(struct bcmgenet_priv *priv) kfree(priv->tx_cbs); } +static void bcmgenet_fini_dma(struct bcmgenet_priv *priv) +{ + int i; + + bcmgenet_fini_tx_ring(priv, DESC_INDEX); + + for (i = 0; i < priv->hw_params->tx_queues; i++) + bcmgenet_fini_tx_ring(priv, i); + + __bcmgenet_fini_dma(priv); +} + /* init_edma: Initialize DMA control register */ static int bcmgenet_init_dma(struct bcmgenet_priv *priv) { @@ -1952,7 +2004,7 @@ static int bcmgenet_init_dma(struct bcmgenet_priv *priv) priv->tx_cbs = kcalloc(priv->num_tx_bds, sizeof(struct enet_cb), GFP_KERNEL); if (!priv->tx_cbs) { - bcmgenet_fini_dma(priv); + __bcmgenet_fini_dma(priv); return -ENOMEM; } @@ -1975,9 +2027,6 @@ static int bcmgenet_poll(struct napi_struct *napi, int budget) struct bcmgenet_priv, napi); unsigned int work_done; - /* tx reclaim */ - bcmgenet_tx_reclaim(priv->dev, &priv->tx_rings[DESC_INDEX]); - work_done = bcmgenet_desc_rx(priv, budget); /* Advancing our consumer index*/ @@ -2022,28 +2071,34 @@ static void bcmgenet_irq_task(struct work_struct *work) static irqreturn_t bcmgenet_isr1(int irq, void *dev_id) { struct bcmgenet_priv *priv = dev_id; + struct bcmgenet_tx_ring *ring; unsigned int index; /* Save irq status for bottom-half processing. */ priv->irq1_stat = bcmgenet_intrl2_1_readl(priv, INTRL2_CPU_STAT) & - ~priv->int1_mask; + ~bcmgenet_intrl2_1_readl(priv, INTRL2_CPU_MASK_STATUS); /* clear interrupts */ bcmgenet_intrl2_1_writel(priv, priv->irq1_stat, INTRL2_CPU_CLEAR); netif_dbg(priv, intr, priv->dev, "%s: IRQ=0x%x\n", __func__, priv->irq1_stat); + /* Check the MBDONE interrupts. * packet is done, reclaim descriptors */ - if (priv->irq1_stat & 0x0000ffff) { - index = 0; - for (index = 0; index < 16; index++) { - if (priv->irq1_stat & (1 << index)) - bcmgenet_tx_reclaim(priv->dev, - &priv->tx_rings[index]); + for (index = 0; index < priv->hw_params->tx_queues; index++) { + if (!(priv->irq1_stat & BIT(index))) + continue; + + ring = &priv->tx_rings[index]; + + if (likely(napi_schedule_prep(&ring->napi))) { + ring->int_disable(priv, ring); + __napi_schedule(&ring->napi); } } + return IRQ_HANDLED; } @@ -2075,8 +2130,12 @@ static irqreturn_t bcmgenet_isr0(int irq, void *dev_id) } if (priv->irq0_stat & (UMAC_IRQ_TXDMA_BDONE | UMAC_IRQ_TXDMA_PDONE)) { - /* Tx reclaim */ - bcmgenet_tx_reclaim(priv->dev, &priv->tx_rings[DESC_INDEX]); + struct bcmgenet_tx_ring *ring = &priv->tx_rings[DESC_INDEX]; + + if (likely(napi_schedule_prep(&ring->napi))) { + ring->int_disable(priv, ring); + __napi_schedule(&ring->napi); + } } if (priv->irq0_stat & (UMAC_IRQ_PHY_DET_R | UMAC_IRQ_PHY_DET_F | diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.h b/drivers/net/ethernet/broadcom/genet/bcmgenet.h index b36ddec0cc0a..0d370d168aee 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.h +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.h @@ -520,6 +520,7 @@ struct bcmgenet_hw_params { struct bcmgenet_tx_ring { spinlock_t lock; /* ring lock */ + struct napi_struct napi; /* NAPI per tx queue */ unsigned int index; /* ring index */ unsigned int queue; /* queue index */ struct enet_cb *cbs; /* tx ring buffer control block*/ @@ -534,6 +535,7 @@ struct bcmgenet_tx_ring { struct bcmgenet_tx_ring *); void (*int_disable)(struct bcmgenet_priv *priv, struct bcmgenet_tx_ring *); + struct bcmgenet_priv *priv; }; /* device context */ -- cgit v1.2.3-59-g8ed1b From a14c7d15ca91b444e77df08b916befdce77562ab Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 27 Feb 2015 17:16:26 +0100 Subject: sh_eth: Fix lost MAC address on kexec Commit 740c7f31c094703c ("sh_eth: Ensure DMA engines are stopped before freeing buffers") added a call to sh_eth_reset() to the sh_eth_set_ringparam() and sh_eth_close() paths. However, setting the software reset bit(s) in the EDMR register resets the MAC Address Registers to zero. Hence after kexec, the new kernel doesn't detect a valid MAC address and assigns a random MAC address, breaking DHCP. Set the MAC address again after the reset in sh_eth_dev_exit() to fix this. Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR). Fixes: 740c7f31c094703c ("sh_eth: Ensure DMA engines are stopped before freeing buffers") Signed-off-by: Geert Uytterhoeven Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 4da8bd263997..654b48d1e61a 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1392,6 +1392,9 @@ static void sh_eth_dev_exit(struct net_device *ndev) msleep(2); /* max frame time at 10 Mbps < 1250 us */ sh_eth_get_stats(ndev); sh_eth_reset(ndev); + + /* Set MAC address again */ + update_mac_address(ndev); } /* free Tx skb function */ -- cgit v1.2.3-59-g8ed1b From cac5e65e8a7ea074f2626d2eaa53aa308452dec4 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 27 Feb 2015 09:42:50 -0800 Subject: net: do not use rcu in rtnl_dump_ifinfo() We did a failed attempt in the past to only use rcu in rtnl dump operations (commit e67f88dd12f6 "net: dont hold rtnl mutex during netlink dump callbacks") Now that dumps are holding RTNL anyway, there is no need to also use rcu locking, as it forbids any scheduling ability, like GFP_KERNEL allocations that controlling path should use instead of GFP_ATOMIC whenever possible. This should fix following splat Cong Wang reported : [ INFO: suspicious RCU usage. ] 3.19.0+ #805 Tainted: G W include/linux/rcupdate.h:538 Illegal context switch in RCU read-side critical section! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 2 locks held by ip/771: #0: (rtnl_mutex){+.+.+.}, at: [] netlink_dump+0x21/0x26c #1: (rcu_read_lock){......}, at: [] rcu_read_lock+0x0/0x6e stack backtrace: CPU: 3 PID: 771 Comm: ip Tainted: G W 3.19.0+ #805 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000001 ffff8800d51e7718 ffffffff81a27457 0000000029e729e6 ffff8800d6108000 ffff8800d51e7748 ffffffff810b539b ffffffff820013dd 00000000000001c8 0000000000000000 ffff8800d7448088 ffff8800d51e7758 Call Trace: [] dump_stack+0x4c/0x65 [] lockdep_rcu_suspicious+0x107/0x110 [] rcu_preempt_sleep_check+0x45/0x47 [] ___might_sleep+0x1d/0x1cb [] __might_sleep+0x78/0x80 [] idr_alloc+0x45/0xd1 [] ? rcu_read_lock_held+0x3b/0x3d [] ? idr_for_each+0x53/0x101 [] alloc_netid+0x61/0x69 [] __peernet2id+0x79/0x8d [] peernet2id+0x13/0x1f [] rtnl_fill_ifinfo+0xa8d/0xc20 [] ? __lock_is_held+0x39/0x52 [] rtnl_dump_ifinfo+0x149/0x213 [] netlink_dump+0xef/0x26c [] netlink_recvmsg+0x17b/0x2c5 [] __sock_recvmsg+0x4e/0x59 [] sock_recvmsg+0x3f/0x51 [] ___sys_recvmsg+0xf6/0x1d9 [] ? handle_pte_fault+0x6e1/0xd3d [] ? native_sched_clock+0x35/0x37 [] ? sched_clock_local+0x12/0x72 [] ? sched_clock_cpu+0x9e/0xb7 [] ? rcu_read_lock_held+0x3b/0x3d [] ? __fcheck_files+0x4c/0x58 [] ? __fget_light+0x2d/0x52 [] __sys_recvmsg+0x42/0x60 [] SyS_recvmsg+0x12/0x1c Signed-off-by: Eric Dumazet Fixes: 0c7aecd4bde4b7302 ("netns: add rtnl cmd to add and get peer netns ids") Cc: Nicolas Dichtel Reported-by: Cong Wang Signed-off-by: David S. Miller --- net/core/rtnetlink.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/net/core/rtnetlink.c b/net/core/rtnetlink.c index 2c49355d16c2..25b4b5d23485 100644 --- a/net/core/rtnetlink.c +++ b/net/core/rtnetlink.c @@ -1300,7 +1300,6 @@ static int rtnl_dump_ifinfo(struct sk_buff *skb, struct netlink_callback *cb) s_h = cb->args[0]; s_idx = cb->args[1]; - rcu_read_lock(); cb->seq = net->dev_base_seq; /* A hack to preserve kernel<->userspace interface. @@ -1322,7 +1321,7 @@ static int rtnl_dump_ifinfo(struct sk_buff *skb, struct netlink_callback *cb) for (h = s_h; h < NETDEV_HASHENTRIES; h++, s_idx = 0) { idx = 0; head = &net->dev_index_head[h]; - hlist_for_each_entry_rcu(dev, head, index_hlist) { + hlist_for_each_entry(dev, head, index_hlist) { if (idx < s_idx) goto cont; err = rtnl_fill_ifinfo(skb, dev, RTM_NEWLINK, @@ -1344,7 +1343,6 @@ cont: } } out: - rcu_read_unlock(); cb->args[1] = idx; cb->args[0] = h; -- cgit v1.2.3-59-g8ed1b From 9d3e2d02f54160725d97f4ab1e1e8de493fbf33a Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Fri, 27 Feb 2015 17:57:09 +0100 Subject: locking/rtmutex: Set state back to running on error The "usual" path is: - rt_mutex_slowlock() - set_current_state() - task_blocks_on_rt_mutex() (ret 0) - __rt_mutex_slowlock() - sleep or not but do return with __set_current_state(TASK_RUNNING) - back to caller. In the early error case where task_blocks_on_rt_mutex() return -EDEADLK we never change the task's state back to RUNNING. I assume this is intended. Without this change after ww_mutex using rt_mutex the selftest passes but later I get plenty of: | bad: scheduling from the idle thread! backtraces. Signed-off-by: Sebastian Andrzej Siewior Acked-by: Mike Galbraith Cc: Linus Torvalds Cc: Maarten Lankhorst Cc: Peter Zijlstra Cc: Thomas Gleixner Fixes: afffc6c1805d ("locking/rtmutex: Optimize setting task running after being blocked") Link: http://lkml.kernel.org/r/1425056229-22326-4-git-send-email-bigeasy@linutronix.de Signed-off-by: Ingo Molnar --- kernel/locking/rtmutex.c | 1 + 1 file changed, 1 insertion(+) diff --git a/kernel/locking/rtmutex.c b/kernel/locking/rtmutex.c index e16e5542bf13..6357265a31ad 100644 --- a/kernel/locking/rtmutex.c +++ b/kernel/locking/rtmutex.c @@ -1193,6 +1193,7 @@ rt_mutex_slowlock(struct rt_mutex *lock, int state, ret = __rt_mutex_slowlock(lock, state, timeout, &waiter); if (unlikely(ret)) { + __set_current_state(TASK_RUNNING); if (rt_mutex_has_waiters(lock)) remove_waiter(lock, &waiter); rt_mutex_handle_deadlock(ret, chwalk, &waiter); -- cgit v1.2.3-59-g8ed1b From 8cdebf71098c07168ef6335e2f1f35d85dbe3049 Mon Sep 17 00:00:00 2001 From: Takashi Sakamoto Date: Sun, 1 Mar 2015 18:12:16 +0900 Subject: ALSA: dice: fix wrong offsets for Dice interface For received packet stream, the offset of 'RX_SEQ_START' locates after the offset of 'RX_NUMBER_MIDI', although current macro and proc output includes wrong offsets. Fortunately, this bug doesn't affect streaming functionality because these macro is not used. This commit fixes these wrong macro and outputs. Signed-off-by: Takashi Sakamoto Signed-off-by: Takashi Iwai --- sound/firewire/dice/dice-interface.h | 18 +++++++++--------- sound/firewire/dice/dice-proc.c | 4 ++-- 2 files changed, 11 insertions(+), 11 deletions(-) diff --git a/sound/firewire/dice/dice-interface.h b/sound/firewire/dice/dice-interface.h index 27b044f84c81..de7602bd69b5 100644 --- a/sound/firewire/dice/dice-interface.h +++ b/sound/firewire/dice/dice-interface.h @@ -298,24 +298,24 @@ */ #define RX_ISOCHRONOUS 0x008 -/* - * Index of first quadlet to be interpreted; read/write. If > 0, that many - * quadlets at the beginning of each data block will be ignored, and all the - * audio and MIDI quadlets will follow. - */ -#define RX_SEQ_START 0x00c - /* * The number of audio channels; read-only. There will be one quadlet per * channel. */ -#define RX_NUMBER_AUDIO 0x010 +#define RX_NUMBER_AUDIO 0x00c /* * The number of MIDI ports, 0-8; read-only. If > 0, there will be one * additional quadlet in each data block, following the audio quadlets. */ -#define RX_NUMBER_MIDI 0x014 +#define RX_NUMBER_MIDI 0x010 + +/* + * Index of first quadlet to be interpreted; read/write. If > 0, that many + * quadlets at the beginning of each data block will be ignored, and all the + * audio and MIDI quadlets will follow. + */ +#define RX_SEQ_START 0x014 /* * Names of all audio channels; read-only. Quadlets are byte-swapped. Names diff --git a/sound/firewire/dice/dice-proc.c b/sound/firewire/dice/dice-proc.c index f5c1d1bced59..ecfe20fd4de5 100644 --- a/sound/firewire/dice/dice-proc.c +++ b/sound/firewire/dice/dice-proc.c @@ -99,9 +99,9 @@ static void dice_proc_read(struct snd_info_entry *entry, } tx; struct { u32 iso; - u32 seq_start; u32 number_audio; u32 number_midi; + u32 seq_start; char names[RX_NAMES_SIZE]; u32 ac3_caps; u32 ac3_enable; @@ -204,10 +204,10 @@ static void dice_proc_read(struct snd_info_entry *entry, break; snd_iprintf(buffer, "rx %u:\n", stream); snd_iprintf(buffer, " iso channel: %d\n", (int)buf.rx.iso); - snd_iprintf(buffer, " sequence start: %u\n", buf.rx.seq_start); snd_iprintf(buffer, " audio channels: %u\n", buf.rx.number_audio); snd_iprintf(buffer, " midi ports: %u\n", buf.rx.number_midi); + snd_iprintf(buffer, " sequence start: %u\n", buf.rx.seq_start); if (quadlets >= 68) { dice_proc_fixup_string(buf.rx.names, RX_NAMES_SIZE); snd_iprintf(buffer, " names: %s\n", buf.rx.names); -- cgit v1.2.3-59-g8ed1b From 2f5c54ce0d11a527de3544e1b2c904544a2c1dd7 Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Fri, 27 Feb 2015 13:19:44 +0200 Subject: net: davinci_mdio: add hibernation callbacks Setting a dev_pm_ops suspend_late/resume_early pair but not a set of hibernation functions means those pm functions will not be called upon hibernation. Fix this by using SET_LATE_SYSTEM_SLEEP_PM_OPS, which appropriately assigns the suspend and hibernation handlers and move davinci_mdio_x callbacks under CONFIG_PM_SLEEP to avoid build warnings. Signed-off-by: Grygorii Strashko Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/davinci_mdio.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c index 98655b44b97e..c00084d689f3 100644 --- a/drivers/net/ethernet/ti/davinci_mdio.c +++ b/drivers/net/ethernet/ti/davinci_mdio.c @@ -423,6 +423,7 @@ static int davinci_mdio_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM_SLEEP static int davinci_mdio_suspend(struct device *dev) { struct davinci_mdio_data *data = dev_get_drvdata(dev); @@ -464,10 +465,10 @@ static int davinci_mdio_resume(struct device *dev) return 0; } +#endif static const struct dev_pm_ops davinci_mdio_pm_ops = { - .suspend_late = davinci_mdio_suspend, - .resume_early = davinci_mdio_resume, + SET_LATE_SYSTEM_SLEEP_PM_OPS(davinci_mdio_suspend, davinci_mdio_resume) }; #if IS_ENABLED(CONFIG_OF) -- cgit v1.2.3-59-g8ed1b From 8963a50453508a3f605dc2b29be35ee72d55335c Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Fri, 27 Feb 2015 13:19:45 +0200 Subject: net: ti: cpsw: add hibernation callbacks Setting a dev_pm_ops suspend/resume pair but not a set of hibernation functions means those pm functions will not be called upon hibernation. Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the suspend and hibernation handlers and move cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP to avoid build warnings. Signed-off-by: Grygorii Strashko Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 49b03368f4b9..a1bbaf6352ba 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -2466,6 +2466,7 @@ static int cpsw_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM_SLEEP static int cpsw_suspend(struct device *dev) { struct platform_device *pdev = to_platform_device(dev); @@ -2518,11 +2519,9 @@ static int cpsw_resume(struct device *dev) } return 0; } +#endif -static const struct dev_pm_ops cpsw_pm_ops = { - .suspend = cpsw_suspend, - .resume = cpsw_resume, -}; +static SIMPLE_DEV_PM_OPS(cpsw_pm_ops, cpsw_suspend, cpsw_resume); static const struct of_device_id cpsw_of_mtable[] = { { .compatible = "ti,cpsw", }, -- cgit v1.2.3-59-g8ed1b From 00c7eb99a5c4bd09a3f4133f61d3ebae787384c7 Mon Sep 17 00:00:00 2001 From: Yannick Guerrini Date: Fri, 27 Feb 2015 18:12:16 +0100 Subject: qlcnic: Fix trivial typo in comment Change 'Firmare' to 'Firmware' Signed-off-by: Yannick Guerrini Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h b/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h index fa4317611fd6..f221126a5c4e 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h @@ -314,7 +314,7 @@ struct qlcnic_fdt { #define QLCNIC_BRDCFG_START 0x4000 /* board config */ #define QLCNIC_BOOTLD_START 0x10000 /* bootld */ #define QLCNIC_IMAGE_START 0x43000 /* compressed image */ -#define QLCNIC_USER_START 0x3E8000 /* Firmare info */ +#define QLCNIC_USER_START 0x3E8000 /* Firmware info */ #define QLCNIC_FW_VERSION_OFFSET (QLCNIC_USER_START+0x408) #define QLCNIC_FW_SIZE_OFFSET (QLCNIC_USER_START+0x40c) -- cgit v1.2.3-59-g8ed1b From f7c306880590f04f9417f84361fa4146103d6de8 Mon Sep 17 00:00:00 2001 From: Yannick Guerrini Date: Fri, 27 Feb 2015 18:38:46 +0100 Subject: netxen_nic: Fix trivial typos in comments Change 'mutliple' to 'multiple' Change 'Firmare' to 'Firmware' Signed-off-by: Yannick Guerrini Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/netxen/netxen_nic.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/qlogic/netxen/netxen_nic.h b/drivers/net/ethernet/qlogic/netxen/netxen_nic.h index 6e426ae94692..0a5e204a0179 100644 --- a/drivers/net/ethernet/qlogic/netxen/netxen_nic.h +++ b/drivers/net/ethernet/qlogic/netxen/netxen_nic.h @@ -354,7 +354,7 @@ struct cmd_desc_type0 { } __attribute__ ((aligned(64))); -/* Note: sizeof(rcv_desc) should always be a mutliple of 2 */ +/* Note: sizeof(rcv_desc) should always be a multiple of 2 */ struct rcv_desc { __le16 reference_handle; __le16 reserved; @@ -499,7 +499,7 @@ struct uni_data_desc{ #define NETXEN_IMAGE_START 0x43000 /* compressed image */ #define NETXEN_SECONDARY_START 0x200000 /* backup images */ #define NETXEN_PXE_START 0x3E0000 /* PXE boot rom */ -#define NETXEN_USER_START 0x3E8000 /* Firmare info */ +#define NETXEN_USER_START 0x3E8000 /* Firmware info */ #define NETXEN_FIXED_START 0x3F0000 /* backup of crbinit */ #define NETXEN_USER_START_OLD NETXEN_PXE_START /* very old flash */ -- cgit v1.2.3-59-g8ed1b From b8b01344eb166740f4dc2f5397fd7fe7c814c16a Mon Sep 17 00:00:00 2001 From: Vaishali Thakkar Date: Fri, 27 Feb 2015 23:40:24 +0530 Subject: net: smc91c92_cs: Use setup_timer and mod_timer Use timer API functions setup_timer and mod_timer instead of structure assignments as they are standard way to set the timer and to update the expire field of an active timer respectively. This is done using Coccinelle and semantic patch used for this is as follows: // @@ expression x,y,z,a,b; @@ -init_timer (&x); +setup_timer (&x, y, z); +mod_timer (&a, b); -x.function = y; -x.data = z; -x.expires = b; -add_timer(&a); // Signed-off-by: Vaishali Thakkar Signed-off-by: David S. Miller --- drivers/net/ethernet/smsc/smc91c92_cs.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/smsc/smc91c92_cs.c b/drivers/net/ethernet/smsc/smc91c92_cs.c index 6b33127ab352..3449893aea8d 100644 --- a/drivers/net/ethernet/smsc/smc91c92_cs.c +++ b/drivers/net/ethernet/smsc/smc91c92_cs.c @@ -1070,11 +1070,8 @@ static int smc_open(struct net_device *dev) smc->packets_waiting = 0; smc_reset(dev); - init_timer(&smc->media); - smc->media.function = media_check; - smc->media.data = (u_long) dev; - smc->media.expires = jiffies + HZ; - add_timer(&smc->media); + setup_timer(&smc->media, media_check, (u_long)dev); + mod_timer(&smc->media, jiffies + HZ); return 0; } /* smc_open */ -- cgit v1.2.3-59-g8ed1b From fc4ba63627948bb395cb54f846470d22eda38ac2 Mon Sep 17 00:00:00 2001 From: Vaishali Thakkar Date: Fri, 27 Feb 2015 23:53:03 +0530 Subject: net: 8390: pcnet_cs: Use setup_timer and mod_timer Use timer API functions setup_timer and mod_timer instead of structure assignments as they are standard way to set the timer and to update the expire field of an active timer respectively. This is done using Coccinelle and semantic patch used for this is as follows: // @@ expression x,y,z,a,b; @@ -init_timer (&x); +setup_timer (&x, y, z); +mod_timer (&a, b); -x.function = y; -x.data = z; -x.expires = b; -add_timer(&a); // Signed-off-by: Vaishali Thakkar Signed-off-by: David S. Miller --- drivers/net/ethernet/8390/pcnet_cs.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/8390/pcnet_cs.c b/drivers/net/ethernet/8390/pcnet_cs.c index 9fb7b9d4fd6c..2777289a26c0 100644 --- a/drivers/net/ethernet/8390/pcnet_cs.c +++ b/drivers/net/ethernet/8390/pcnet_cs.c @@ -918,11 +918,8 @@ static int pcnet_open(struct net_device *dev) info->phy_id = info->eth_phy; info->link_status = 0x00; - init_timer(&info->watchdog); - info->watchdog.function = ei_watchdog; - info->watchdog.data = (u_long)dev; - info->watchdog.expires = jiffies + HZ; - add_timer(&info->watchdog); + setup_timer(&info->watchdog, ei_watchdog, (u_long)dev); + mod_timer(&info->watchdog, jiffies + HZ); return ei_open(dev); } /* pcnet_open */ -- cgit v1.2.3-59-g8ed1b From 6753a971bef3d91f25571a5da24abbfd76459114 Mon Sep 17 00:00:00 2001 From: Vaishali Thakkar Date: Sat, 28 Feb 2015 00:02:34 +0530 Subject: net: 8390: axnet_cs: Use setup_timer and mod_timer Use timer API functions setup_timer and mod_timer instead of structure assignments as they are standard way to set the timer and to update the expire field of an active timer respectively. This is done using Coccinelle and semantic patch used for this is as follows: // @@ expression x,y,z,a,b; @@ -init_timer (&x); +setup_timer (&x, y, z); +mod_timer (&a, b); -x.function = y; -x.data = z; -x.expires = b; -add_timer(&a); // Signed-off-by: Vaishali Thakkar Signed-off-by: David S. Miller --- drivers/net/ethernet/8390/axnet_cs.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/8390/axnet_cs.c b/drivers/net/ethernet/8390/axnet_cs.c index 7769c05543f1..ec6eac1f8c95 100644 --- a/drivers/net/ethernet/8390/axnet_cs.c +++ b/drivers/net/ethernet/8390/axnet_cs.c @@ -484,11 +484,8 @@ static int axnet_open(struct net_device *dev) link->open++; info->link_status = 0x00; - init_timer(&info->watchdog); - info->watchdog.function = ei_watchdog; - info->watchdog.data = (u_long)dev; - info->watchdog.expires = jiffies + HZ; - add_timer(&info->watchdog); + setup_timer(&info->watchdog, ei_watchdog, (u_long)dev); + mod_timer(&info->watchdog, jiffies + HZ); return ax_open(dev); } /* axnet_open */ -- cgit v1.2.3-59-g8ed1b From ccb36da19b36a77dce926efeb76de0ab57c00ad5 Mon Sep 17 00:00:00 2001 From: Vaishali Thakkar Date: Sat, 28 Feb 2015 00:12:34 +0530 Subject: net: stmmac: Use setup_timer and mod_timer Use timer API functions setup_timer and mod_timer instead of structure assignments as they are standard way to set the timer and to update the expire field of an active timer respectively. This is done using Coccinelle and semantic patch used for this is as follows: // @@ expression x,y,z,a,b; @@ -init_timer (&x); +setup_timer (&x, y, z); +mod_timer (&a, b); -x.function = y; -x.data = z; -x.expires = b; -add_timer(&a); // Signed-off-by: Vaishali Thakkar Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 55e89b3838f1..a0ea84fe6519 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -310,11 +310,11 @@ bool stmmac_eee_init(struct stmmac_priv *priv) spin_lock_irqsave(&priv->lock, flags); if (!priv->eee_active) { priv->eee_active = 1; - init_timer(&priv->eee_ctrl_timer); - priv->eee_ctrl_timer.function = stmmac_eee_ctrl_timer; - priv->eee_ctrl_timer.data = (unsigned long)priv; - priv->eee_ctrl_timer.expires = STMMAC_LPI_T(eee_timer); - add_timer(&priv->eee_ctrl_timer); + setup_timer(&priv->eee_ctrl_timer, + stmmac_eee_ctrl_timer, + (unsigned long)priv); + mod_timer(&priv->eee_ctrl_timer, + STMMAC_LPI_T(eee_timer)); priv->hw->mac->set_eee_timer(priv->hw, STMMAC_DEFAULT_LIT_LS, -- cgit v1.2.3-59-g8ed1b From 187d67858bafd16334d150b0fa7cff1f5814c6fb Mon Sep 17 00:00:00 2001 From: Vaishali Thakkar Date: Sat, 28 Feb 2015 00:20:59 +0530 Subject: net: pasemi: Use setup_timer and mod_timer Use timer API functions setup_timer and mod_timer instead of structure assignments as they are standard way to set the timer and to update the expire field of an active timer respectively. This is done using Coccinelle and semantic patch used for this is as follows: // @@ expression x,y,z,a,b; @@ -init_timer (&x); +setup_timer (&x, y, z); +mod_timer (&a, b); -x.function = y; -x.data = z; -x.expires = b; -add_timer(&a); // Signed-off-by: Vaishali Thakkar Signed-off-by: David S. Miller --- drivers/net/ethernet/pasemi/pasemi_mac.c | 8 +++----- 1 file changed, 3 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/pasemi/pasemi_mac.c b/drivers/net/ethernet/pasemi/pasemi_mac.c index 44e8d7d25547..57a6e6cd74fc 100644 --- a/drivers/net/ethernet/pasemi/pasemi_mac.c +++ b/drivers/net/ethernet/pasemi/pasemi_mac.c @@ -1239,11 +1239,9 @@ static int pasemi_mac_open(struct net_device *dev) if (mac->phydev) phy_start(mac->phydev); - init_timer(&mac->tx->clean_timer); - mac->tx->clean_timer.function = pasemi_mac_tx_timer; - mac->tx->clean_timer.data = (unsigned long)mac->tx; - mac->tx->clean_timer.expires = jiffies+HZ; - add_timer(&mac->tx->clean_timer); + setup_timer(&mac->tx->clean_timer, pasemi_mac_tx_timer, + (unsigned long)mac->tx); + mod_timer(&mac->tx->clean_timer, jiffies + HZ); return 0; -- cgit v1.2.3-59-g8ed1b From 56b08fdcf637955d3023d769afd6cdabc526ba22 Mon Sep 17 00:00:00 2001 From: Arvid Brodin Date: Fri, 27 Feb 2015 21:26:03 +0100 Subject: net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface. To repeat: $ sudo ip link del hsr0 BUG: unable to handle kernel NULL pointer dereference at 0000000000000018 IP: [] hsr_del_port+0x15/0xa0 etc... Bug description: As part of the hsr master device destruction, hsr_del_port() is called for each of the hsr ports. At each such call, the master device is updated regarding features and mtu. When the master device is freed before the slave interfaces, master will be NULL in hsr_del_port(), which led to a NULL pointer dereference. Additionally, dev_put() was called on the master device itself in hsr_del_port(), causing a refcnt error. A third bug in the same code path was that the rtnl lock was not taken before hsr_del_port() was called as part of hsr_dev_destroy(). The reporter (Nicolas Dichtel) also said: "hsr_netdev_notify() supposes that the port will always be available when the notification is for an hsr interface. It's wrong. For example, netdev_wait_allrefs() may resend NETDEV_UNREGISTER.". As a precaution against this, a check for port == NULL was added in hsr_dev_notify(). Reported-by: Nicolas Dichtel Fixes: 51f3c605318b056a ("net/hsr: Move slave init to hsr_slave.c.") Signed-off-by: Arvid Brodin Signed-off-by: David S. Miller --- net/hsr/hsr_device.c | 3 +++ net/hsr/hsr_main.c | 4 ++++ net/hsr/hsr_slave.c | 10 +++++++--- 3 files changed, 14 insertions(+), 3 deletions(-) diff --git a/net/hsr/hsr_device.c b/net/hsr/hsr_device.c index a138d75751df..44d27469ae55 100644 --- a/net/hsr/hsr_device.c +++ b/net/hsr/hsr_device.c @@ -359,8 +359,11 @@ static void hsr_dev_destroy(struct net_device *hsr_dev) struct hsr_port *port; hsr = netdev_priv(hsr_dev); + + rtnl_lock(); hsr_for_each_port(hsr, port) hsr_del_port(port); + rtnl_unlock(); del_timer_sync(&hsr->prune_timer); del_timer_sync(&hsr->announce_timer); diff --git a/net/hsr/hsr_main.c b/net/hsr/hsr_main.c index 779d28b65417..cd37d0011b42 100644 --- a/net/hsr/hsr_main.c +++ b/net/hsr/hsr_main.c @@ -36,6 +36,10 @@ static int hsr_netdev_notify(struct notifier_block *nb, unsigned long event, return NOTIFY_DONE; /* Not an HSR device */ hsr = netdev_priv(dev); port = hsr_port_get_hsr(hsr, HSR_PT_MASTER); + if (port == NULL) { + /* Resend of notification concerning removed device? */ + return NOTIFY_DONE; + } } else { hsr = port->hsr; } diff --git a/net/hsr/hsr_slave.c b/net/hsr/hsr_slave.c index a348dcbcd683..7d37366cc695 100644 --- a/net/hsr/hsr_slave.c +++ b/net/hsr/hsr_slave.c @@ -181,8 +181,10 @@ void hsr_del_port(struct hsr_port *port) list_del_rcu(&port->port_list); if (port != master) { - netdev_update_features(master->dev); - dev_set_mtu(master->dev, hsr_get_max_mtu(hsr)); + if (master != NULL) { + netdev_update_features(master->dev); + dev_set_mtu(master->dev, hsr_get_max_mtu(hsr)); + } netdev_rx_handler_unregister(port->dev); dev_set_promiscuity(port->dev, -1); } @@ -192,5 +194,7 @@ void hsr_del_port(struct hsr_port *port) */ synchronize_rcu(); - dev_put(port->dev); + + if (port != master) + dev_put(port->dev); } -- cgit v1.2.3-59-g8ed1b From c03ae533a9c4de83a35105f9bfd7152d916b4680 Mon Sep 17 00:00:00 2001 From: Florian Westphal Date: Sat, 28 Feb 2015 11:51:36 +0100 Subject: rxrpc: terminate retrans loop when sending of skb fails Typo, 'stop' is never set to true. Seems intent is to not attempt to retransmit more packets after sendmsg returns an error. This change is based on code inspection only. Signed-off-by: Florian Westphal Signed-off-by: David S. Miller --- net/rxrpc/ar-ack.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/net/rxrpc/ar-ack.c b/net/rxrpc/ar-ack.c index c6be17a959a6..40404183a5da 100644 --- a/net/rxrpc/ar-ack.c +++ b/net/rxrpc/ar-ack.c @@ -218,7 +218,8 @@ static void rxrpc_resend(struct rxrpc_call *call) struct rxrpc_header *hdr; struct sk_buff *txb; unsigned long *p_txb, resend_at; - int loop, stop; + bool stop; + int loop; u8 resend; _enter("{%d,%d,%d,%d},", @@ -226,7 +227,7 @@ static void rxrpc_resend(struct rxrpc_call *call) atomic_read(&call->sequence), CIRC_CNT(call->acks_head, call->acks_tail, call->acks_winsz)); - stop = 0; + stop = false; resend = 0; resend_at = 0; @@ -255,7 +256,7 @@ static void rxrpc_resend(struct rxrpc_call *call) _proto("Tx DATA %%%u { #%d }", ntohl(sp->hdr.serial), ntohl(sp->hdr.seq)); if (rxrpc_send_packet(call->conn->trans, txb) < 0) { - stop = 0; + stop = true; sp->resend_at = jiffies + 3; } else { sp->resend_at = -- cgit v1.2.3-59-g8ed1b From 765dd3bb44711b4ba36c1e06f9c4b7bfe73ffef7 Mon Sep 17 00:00:00 2001 From: Florian Westphal Date: Sat, 28 Feb 2015 11:51:37 +0100 Subject: rxrpc: don't multiply with HZ twice rxrpc_resend_timeout has an initial value of 4 * HZ; use it as-is. Signed-off-by: Florian Westphal Signed-off-by: David S. Miller --- net/rxrpc/ar-ack.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/rxrpc/ar-ack.c b/net/rxrpc/ar-ack.c index 40404183a5da..e0547f521f20 100644 --- a/net/rxrpc/ar-ack.c +++ b/net/rxrpc/ar-ack.c @@ -260,7 +260,7 @@ static void rxrpc_resend(struct rxrpc_call *call) sp->resend_at = jiffies + 3; } else { sp->resend_at = - jiffies + rxrpc_resend_timeout * HZ; + jiffies + rxrpc_resend_timeout; } } -- cgit v1.2.3-59-g8ed1b From f62ba9c14b85a682b64a4c421f91de0bd2aa8538 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Sat, 28 Feb 2015 18:09:16 -0800 Subject: net: bcmgenet: fix software maintained statistics Commit 44c8bc3ce39f ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures") added a few software maintained statistics using BCMGENET_STAT_MIB_RX and BCMGENET_STAT_MIB_TX. These statistics are read from the hardware MIB counters, such that bcmgenet_update_mib_counters() was trying to read from a non-existing MIB offset for these counters. Fix this by introducing a special type: BCMGENET_STAT_SOFT, similar to BCMGENET_STAT_NETDEV, such that bcmgenet_get_ethtool_stats will read from the software mib. Fixes: 44c8bc3ce39f ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/genet/bcmgenet.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c index 2874a004f815..6befde61c203 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c @@ -487,6 +487,7 @@ enum bcmgenet_stat_type { BCMGENET_STAT_MIB_TX, BCMGENET_STAT_RUNT, BCMGENET_STAT_MISC, + BCMGENET_STAT_SOFT, }; struct bcmgenet_stats { @@ -515,6 +516,7 @@ struct bcmgenet_stats { #define STAT_GENET_MIB_RX(str, m) STAT_GENET_MIB(str, m, BCMGENET_STAT_MIB_RX) #define STAT_GENET_MIB_TX(str, m) STAT_GENET_MIB(str, m, BCMGENET_STAT_MIB_TX) #define STAT_GENET_RUNT(str, m) STAT_GENET_MIB(str, m, BCMGENET_STAT_RUNT) +#define STAT_GENET_SOFT_MIB(str, m) STAT_GENET_MIB(str, m, BCMGENET_STAT_SOFT) #define STAT_GENET_MISC(str, m, offset) { \ .stat_string = str, \ @@ -614,9 +616,9 @@ static const struct bcmgenet_stats bcmgenet_gstrings_stats[] = { UMAC_RBUF_OVFL_CNT), STAT_GENET_MISC("rbuf_err_cnt", mib.rbuf_err_cnt, UMAC_RBUF_ERR_CNT), STAT_GENET_MISC("mdf_err_cnt", mib.mdf_err_cnt, UMAC_MDF_ERR_CNT), - STAT_GENET_MIB_RX("alloc_rx_buff_failed", mib.alloc_rx_buff_failed), - STAT_GENET_MIB_RX("rx_dma_failed", mib.rx_dma_failed), - STAT_GENET_MIB_TX("tx_dma_failed", mib.tx_dma_failed), + STAT_GENET_SOFT_MIB("alloc_rx_buff_failed", mib.alloc_rx_buff_failed), + STAT_GENET_SOFT_MIB("rx_dma_failed", mib.rx_dma_failed), + STAT_GENET_SOFT_MIB("tx_dma_failed", mib.tx_dma_failed), }; #define BCMGENET_STATS_LEN ARRAY_SIZE(bcmgenet_gstrings_stats) @@ -668,6 +670,7 @@ static void bcmgenet_update_mib_counters(struct bcmgenet_priv *priv) s = &bcmgenet_gstrings_stats[i]; switch (s->type) { case BCMGENET_STAT_NETDEV: + case BCMGENET_STAT_SOFT: continue; case BCMGENET_STAT_MIB_RX: case BCMGENET_STAT_MIB_TX: -- cgit v1.2.3-59-g8ed1b From 55ff4ea9a853f5ec9a8290c0ccc1d00c97e49f82 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Sat, 28 Feb 2015 18:09:17 -0800 Subject: net: systemport: fix software maintained statistics Commit 60b4ea1781fd ("net: systemport: log RX buffer allocation and RX/TX DMA failures") added a few software maintained statistics using BCM_SYSPORT_STAT_MIB_RX and BCM_SYSPORT_STAT_MIB_TX. These statistics are read from the hardware MIB counters, such that bcm_sysport_update_mib_counters() was trying to read from a non-existing MIB offset for these counters. Fix this by introducing a special type: BCM_SYSPORT_STAT_SOFT, similar to BCM_SYSPORT_STAT_NETDEV, such that bcm_sysport_get_ethtool_stats will read from the software mib. Fixes: 60b4ea1781fd ("net: systemport: log RX buffer allocation and RX/TX DMA failures") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bcmsysport.c | 7 ++++--- drivers/net/ethernet/broadcom/bcmsysport.h | 2 ++ 2 files changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/broadcom/bcmsysport.c b/drivers/net/ethernet/broadcom/bcmsysport.c index 5b308a4a4d0e..783543ad1fcf 100644 --- a/drivers/net/ethernet/broadcom/bcmsysport.c +++ b/drivers/net/ethernet/broadcom/bcmsysport.c @@ -274,9 +274,9 @@ static const struct bcm_sysport_stats bcm_sysport_gstrings_stats[] = { /* RBUF misc statistics */ STAT_RBUF("rbuf_ovflow_cnt", mib.rbuf_ovflow_cnt, RBUF_OVFL_DISC_CNTR), STAT_RBUF("rbuf_err_cnt", mib.rbuf_err_cnt, RBUF_ERR_PKT_CNTR), - STAT_MIB_RX("alloc_rx_buff_failed", mib.alloc_rx_buff_failed), - STAT_MIB_RX("rx_dma_failed", mib.rx_dma_failed), - STAT_MIB_TX("tx_dma_failed", mib.tx_dma_failed), + STAT_MIB_SOFT("alloc_rx_buff_failed", mib.alloc_rx_buff_failed), + STAT_MIB_SOFT("rx_dma_failed", mib.rx_dma_failed), + STAT_MIB_SOFT("tx_dma_failed", mib.tx_dma_failed), }; #define BCM_SYSPORT_STATS_LEN ARRAY_SIZE(bcm_sysport_gstrings_stats) @@ -345,6 +345,7 @@ static void bcm_sysport_update_mib_counters(struct bcm_sysport_priv *priv) s = &bcm_sysport_gstrings_stats[i]; switch (s->type) { case BCM_SYSPORT_STAT_NETDEV: + case BCM_SYSPORT_STAT_SOFT: continue; case BCM_SYSPORT_STAT_MIB_RX: case BCM_SYSPORT_STAT_MIB_TX: diff --git a/drivers/net/ethernet/broadcom/bcmsysport.h b/drivers/net/ethernet/broadcom/bcmsysport.h index fc19417d82a5..7e3d87a88c76 100644 --- a/drivers/net/ethernet/broadcom/bcmsysport.h +++ b/drivers/net/ethernet/broadcom/bcmsysport.h @@ -570,6 +570,7 @@ enum bcm_sysport_stat_type { BCM_SYSPORT_STAT_RUNT, BCM_SYSPORT_STAT_RXCHK, BCM_SYSPORT_STAT_RBUF, + BCM_SYSPORT_STAT_SOFT, }; /* Macros to help define ethtool statistics */ @@ -590,6 +591,7 @@ enum bcm_sysport_stat_type { #define STAT_MIB_RX(str, m) STAT_MIB(str, m, BCM_SYSPORT_STAT_MIB_RX) #define STAT_MIB_TX(str, m) STAT_MIB(str, m, BCM_SYSPORT_STAT_MIB_TX) #define STAT_RUNT(str, m) STAT_MIB(str, m, BCM_SYSPORT_STAT_RUNT) +#define STAT_MIB_SOFT(str, m) STAT_MIB(str, m, BCM_SYSPORT_STAT_SOFT) #define STAT_RXCHK(str, m, ofs) { \ .stat_string = str, \ -- cgit v1.2.3-59-g8ed1b From f4c72c70308897bd26f2918979d06b429916fd0e Mon Sep 17 00:00:00 2001 From: Andrey Ryabinin Date: Fri, 27 Feb 2015 20:44:21 +0300 Subject: android: binder: fix binder mmap failures binder_update_page_range() initializes only addr and size fields in 'struct vm_struct tmp_area;' and passes it to map_vm_area(). Before 71394fe50146 ("mm: vmalloc: add flag preventing guard hole allocation") this was because map_vm_area() didn't use any other fields in vm_struct except addr and size. Now get_vm_area_size() (used in map_vm_area()) reads vm_struct's flags to determine whether vm area has guard hole or not. binder_update_page_range() don't initialize flags field, so this causes following binder mmap failures: -----------[ cut here ]------------ WARNING: CPU: 0 PID: 1971 at mm/vmalloc.c:130 vmap_page_range_noflush+0x119/0x144() CPU: 0 PID: 1971 Comm: healthd Not tainted 4.0.0-rc1-00399-g7da3fdc-dirty #157 Hardware name: ARM-Versatile Express [] (unwind_backtrace) from [] (show_stack+0x11/0x14) [] (show_stack) from [] (dump_stack+0x59/0x7c) [] (dump_stack) from [] (warn_slowpath_common+0x55/0x84) [] (warn_slowpath_common) from [] (warn_slowpath_null+0x17/0x1c) [] (warn_slowpath_null) from [] (vmap_page_range_noflush+0x119/0x144) [] (vmap_page_range_noflush) from [] (map_vm_area+0x27/0x48) [] (map_vm_area) from [] (binder_update_page_range+0x12f/0x27c) [] (binder_update_page_range) from [] (binder_mmap+0xbf/0x1ac) [] (binder_mmap) from [] (mmap_region+0x2eb/0x4d4) [] (mmap_region) from [] (do_mmap_pgoff+0x1e7/0x250) [] (do_mmap_pgoff) from [] (vm_mmap_pgoff+0x45/0x60) [] (vm_mmap_pgoff) from [] (SyS_mmap_pgoff+0x5d/0x80) [] (SyS_mmap_pgoff) from [] (ret_fast_syscall+0x1/0x5c) ---[ end trace 48c2c4b9a1349e54 ]--- binder: 1982: binder_alloc_buf failed to map page at f0e00000 in kernel binder: binder_mmap: 1982 b6bde000-b6cdc000 alloc small buf failed -12 Use map_kernel_range_noflush() instead of map_vm_area() as this is better API for binder's purposes and it allows to get rid of 'vm_struct tmp_area' at all. Fixes: 71394fe50146 ("mm: vmalloc: add flag preventing guard hole allocation") Signed-off-by: Andrey Ryabinin Reported-by: Amit Pundir Tested-by: Amit Pundir Acked-by: David Rientjes Tested-by: John Stultz Signed-off-by: Greg Kroah-Hartman --- drivers/android/binder.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/android/binder.c b/drivers/android/binder.c index 33b09b6568a4..6607f3c6ace1 100644 --- a/drivers/android/binder.c +++ b/drivers/android/binder.c @@ -551,7 +551,6 @@ static int binder_update_page_range(struct binder_proc *proc, int allocate, { void *page_addr; unsigned long user_page_addr; - struct vm_struct tmp_area; struct page **page; struct mm_struct *mm; @@ -600,10 +599,11 @@ static int binder_update_page_range(struct binder_proc *proc, int allocate, proc->pid, page_addr); goto err_alloc_page_failed; } - tmp_area.addr = page_addr; - tmp_area.size = PAGE_SIZE + PAGE_SIZE /* guard page? */; - ret = map_vm_area(&tmp_area, PAGE_KERNEL, page); - if (ret) { + ret = map_kernel_range_noflush((unsigned long)page_addr, + PAGE_SIZE, PAGE_KERNEL, page); + flush_cache_vmap((unsigned long)page_addr, + (unsigned long)page_addr + PAGE_SIZE); + if (ret != 1) { pr_err("%d: binder_alloc_buf failed to map page at %p in kernel\n", proc->pid, page_addr); goto err_map_kernel_failed; -- cgit v1.2.3-59-g8ed1b From abe46b8932dd9a6dfc3698e3eb121809b7b9ed28 Mon Sep 17 00:00:00 2001 From: Ian Abbott Date: Fri, 27 Feb 2015 16:04:42 +0000 Subject: staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel Reading of analog input channels by the `INSN_READ` comedi instruction is broken for all except channel 0. `pci171x_ai_insn_read()` calls `pci171x_ai_read_sample()` with the wrong value for the third parameter. It is supposed to be the current index in a channel list (which is always of length 1 in this case, so the index should be 0), but instead it is passing the actual channel number. `pci171x_ai_read_sample()` checks the channel number encoded in the raw sample value read from the hardware matches the channel number stored in the specified index of the previously set up channel list and returns `-ENODATA` if it doesn't match. Since the index should always be 0 in this case, the match will fail unless the channel number is also 0. Fix it by passing 0 as the channel index. Note that when the bug first appeared, it was `pci171x_ai_dropout()` that was called with the wrong parameter value. `pci171x_ai_dropout()` got replaced with `pci171x_ai_read_sample()` in commit 7fd2dae2500d ("staging: comedi: adv_pci1710: introduce pci171x_ai_read_sample()"). Fixes: 16c7eb6047bb ("staging: comedi: adv_pci1710: always enable PCI171x_PARANOIDCHECK code") Signed-off-by: Ian Abbott Cc: stable # 3.16+ Signed-off-by: Greg Kroah-Hartman --- drivers/staging/comedi/drivers/adv_pci1710.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/staging/comedi/drivers/adv_pci1710.c b/drivers/staging/comedi/drivers/adv_pci1710.c index 9800c01e6fb9..3f72451d2de0 100644 --- a/drivers/staging/comedi/drivers/adv_pci1710.c +++ b/drivers/staging/comedi/drivers/adv_pci1710.c @@ -426,7 +426,6 @@ static int pci171x_ai_insn_read(struct comedi_device *dev, unsigned int *data) { struct pci1710_private *devpriv = dev->private; - unsigned int chan = CR_CHAN(insn->chanspec); int ret = 0; int i; @@ -447,7 +446,7 @@ static int pci171x_ai_insn_read(struct comedi_device *dev, if (ret) break; - ret = pci171x_ai_read_sample(dev, s, chan, &val); + ret = pci171x_ai_read_sample(dev, s, 0, &val); if (ret) break; -- cgit v1.2.3-59-g8ed1b From 6c15a8516b8118eb19a59fd0bd22df41b9101c32 Mon Sep 17 00:00:00 2001 From: Alexander Usyskin Date: Tue, 10 Feb 2015 10:36:36 +0200 Subject: mei: make device disabled on stop unconditionally Set the internal device state to to disabled after hardware reset in stop flow. This will cover cases when driver was not brought to disabled state because of an error and in stop flow we wish not to retry the reset. Cc: #3.10+ Signed-off-by: Alexander Usyskin Signed-off-by: Tomas Winkler Signed-off-by: Greg Kroah-Hartman --- drivers/misc/mei/init.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/misc/mei/init.c b/drivers/misc/mei/init.c index 9306219d5675..6ad049a08e4d 100644 --- a/drivers/misc/mei/init.c +++ b/drivers/misc/mei/init.c @@ -341,6 +341,8 @@ void mei_stop(struct mei_device *dev) dev->dev_state = MEI_DEV_POWER_DOWN; mei_reset(dev); + /* move device to disabled state unconditionally */ + dev->dev_state = MEI_DEV_DISABLED; mutex_unlock(&dev->device_lock); -- cgit v1.2.3-59-g8ed1b From aa5accea404b2b92d39c1924cfeb90f6082f6389 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Fri, 27 Feb 2015 22:54:19 -0500 Subject: NFS: Ensure that buffered writes wait for O_DIRECT writes to complete The O_DIRECT code will grab the inode->i_mutex and flush out buffered writes, before scheduling a read or a write. However there is no equivalent in the buffered write code to wait for O_DIRECT to complete. Fixes a reported issue in xfstests generic/133, when first performing an O_DIRECT write followed by a buffered write. Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/file.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/fs/nfs/file.c b/fs/nfs/file.c index 94712fc781fa..c045c7169fa0 100644 --- a/fs/nfs/file.c +++ b/fs/nfs/file.c @@ -372,6 +372,10 @@ start: nfs_wait_bit_killable, TASK_KILLABLE); if (ret) return ret; + /* + * Wait for O_DIRECT to complete + */ + nfs_inode_dio_wait(mapping->host); page = grab_cache_page_write_begin(mapping, index, flags); if (!page) -- cgit v1.2.3-59-g8ed1b From 140e049c64ce848392adbf4678983ecc76888dde Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 17:42:42 -0500 Subject: NFS: Add a helper to set attribute barriers Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 16 ++++++++++++++++ include/linux/nfs_fs.h | 1 + 2 files changed, 17 insertions(+) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index 83107be3dd01..b0cbc1ba82da 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1260,6 +1260,22 @@ void nfs_fattr_init(struct nfs_fattr *fattr) } EXPORT_SYMBOL_GPL(nfs_fattr_init); +/** + * nfs_fattr_set_barrier + * @fattr: attributes + * + * Used to set a barrier after an attribute was updated. This + * barrier ensures that older attributes from RPC calls that may + * have raced with our update cannot clobber these new values. + * Note that you are still responsible for ensuring that other + * operations which change the attribute on the server do not + * collide. + */ +void nfs_fattr_set_barrier(struct nfs_fattr *fattr) +{ + fattr->gencount = nfs_inc_attr_generation_counter(); +} + struct nfs_fattr *nfs_alloc_fattr(void) { struct nfs_fattr *fattr; diff --git a/include/linux/nfs_fs.h b/include/linux/nfs_fs.h index 2f77e0c651c8..3a4ffb5856cd 100644 --- a/include/linux/nfs_fs.h +++ b/include/linux/nfs_fs.h @@ -369,6 +369,7 @@ extern struct nfs_lock_context *nfs_get_lock_context(struct nfs_open_context *ct extern void nfs_put_lock_context(struct nfs_lock_context *l_ctx); extern u64 nfs_compat_user_ino64(u64 fileid); extern void nfs_fattr_init(struct nfs_fattr *fattr); +extern void nfs_fattr_set_barrier(struct nfs_fattr *fattr); extern unsigned long nfs_inc_attr_generation_counter(void); extern struct nfs_fattr *nfs_alloc_fattr(void); -- cgit v1.2.3-59-g8ed1b From f044636d972246d451e06226cc1675d5da389762 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 16:09:04 -0500 Subject: NFS: Add attribute update barriers to nfs_setattr_update_inode() Ensure that other operations which raced with our setattr RPC call cannot revert the file attribute changes that were made on the server. To do so, we artificially bump the attribute generation counter on the inode so that all calls to nfs_fattr_init() that precede ours will be dropped. The motivation for the patch came from Chuck Lever's reports of readaheads racing with truncate operations and causing the file size to be reverted. Reported-by: Chuck Lever Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 17 ++++++++++++----- fs/nfs/nfs3proc.c | 2 +- fs/nfs/nfs4proc.c | 6 +++--- fs/nfs/proc.c | 2 +- include/linux/nfs_fs.h | 2 +- 5 files changed, 18 insertions(+), 11 deletions(-) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index b0cbc1ba82da..3a2d127de499 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -556,6 +556,7 @@ EXPORT_SYMBOL_GPL(nfs_setattr); * This is a copy of the common vmtruncate, but with the locking * corrected to take into account the fact that NFS requires * inode->i_size to be updated under the inode->i_lock. + * Note: must be called with inode->i_lock held! */ static int nfs_vmtruncate(struct inode * inode, loff_t offset) { @@ -565,14 +566,14 @@ static int nfs_vmtruncate(struct inode * inode, loff_t offset) if (err) goto out; - spin_lock(&inode->i_lock); i_size_write(inode, offset); /* Optimisation */ if (offset == 0) NFS_I(inode)->cache_validity &= ~NFS_INO_INVALID_DATA; - spin_unlock(&inode->i_lock); + spin_unlock(&inode->i_lock); truncate_pagecache(inode, offset); + spin_lock(&inode->i_lock); out: return err; } @@ -585,10 +586,15 @@ out: * Note: we do this in the *proc.c in order to ensure that * it works for things like exclusive creates too. */ -void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr) +void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr, + struct nfs_fattr *fattr) { + /* Barrier: bump the attribute generation count. */ + nfs_fattr_set_barrier(fattr); + + spin_lock(&inode->i_lock); + NFS_I(inode)->attr_gencount = fattr->gencount; if ((attr->ia_valid & (ATTR_MODE|ATTR_UID|ATTR_GID)) != 0) { - spin_lock(&inode->i_lock); if ((attr->ia_valid & ATTR_MODE) != 0) { int mode = attr->ia_mode & S_IALLUGO; mode |= inode->i_mode & ~S_IALLUGO; @@ -600,12 +606,13 @@ void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr) inode->i_gid = attr->ia_gid; nfs_set_cache_invalid(inode, NFS_INO_INVALID_ACCESS | NFS_INO_INVALID_ACL); - spin_unlock(&inode->i_lock); } if ((attr->ia_valid & ATTR_SIZE) != 0) { nfs_inc_stats(inode, NFSIOS_SETATTRTRUNC); nfs_vmtruncate(inode, attr->ia_size); } + nfs_update_inode(inode, fattr); + spin_unlock(&inode->i_lock); } EXPORT_SYMBOL_GPL(nfs_setattr_update_inode); diff --git a/fs/nfs/nfs3proc.c b/fs/nfs/nfs3proc.c index 78e557c3ab87..11109a137c0c 100644 --- a/fs/nfs/nfs3proc.c +++ b/fs/nfs/nfs3proc.c @@ -138,7 +138,7 @@ nfs3_proc_setattr(struct dentry *dentry, struct nfs_fattr *fattr, nfs_fattr_init(fattr); status = rpc_call_sync(NFS_CLIENT(inode), &msg, 0); if (status == 0) - nfs_setattr_update_inode(inode, sattr); + nfs_setattr_update_inode(inode, sattr, fattr); dprintk("NFS reply setattr: %d\n", status); return status; } diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index 4e41340e957d..c499e02a58ca 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -2416,8 +2416,8 @@ static int _nfs4_do_open(struct inode *dir, opendata->o_res.f_attr, sattr, state, label, olabel); if (status == 0) { - nfs_setattr_update_inode(state->inode, sattr); - nfs_post_op_update_inode(state->inode, opendata->o_res.f_attr); + nfs_setattr_update_inode(state->inode, sattr, + opendata->o_res.f_attr); nfs_setsecurity(state->inode, opendata->o_res.f_attr, olabel); } } @@ -3291,7 +3291,7 @@ nfs4_proc_setattr(struct dentry *dentry, struct nfs_fattr *fattr, status = nfs4_do_setattr(inode, cred, fattr, sattr, state, NULL, label); if (status == 0) { - nfs_setattr_update_inode(inode, sattr); + nfs_setattr_update_inode(inode, sattr, fattr); nfs_setsecurity(inode, fattr, label); } nfs4_label_free(label); diff --git a/fs/nfs/proc.c b/fs/nfs/proc.c index b09cc23d6f43..6202bc0f11bb 100644 --- a/fs/nfs/proc.c +++ b/fs/nfs/proc.c @@ -139,7 +139,7 @@ nfs_proc_setattr(struct dentry *dentry, struct nfs_fattr *fattr, nfs_fattr_init(fattr); status = rpc_call_sync(NFS_CLIENT(inode), &msg, 0); if (status == 0) - nfs_setattr_update_inode(inode, sattr); + nfs_setattr_update_inode(inode, sattr, fattr); dprintk("NFS reply setattr: %d\n", status); return status; } diff --git a/include/linux/nfs_fs.h b/include/linux/nfs_fs.h index 3a4ffb5856cd..f26e64e0aff8 100644 --- a/include/linux/nfs_fs.h +++ b/include/linux/nfs_fs.h @@ -356,7 +356,7 @@ extern int nfs_revalidate_inode_rcu(struct nfs_server *server, struct inode *ino extern int __nfs_revalidate_inode(struct nfs_server *, struct inode *); extern int nfs_revalidate_mapping(struct inode *inode, struct address_space *mapping); extern int nfs_setattr(struct dentry *, struct iattr *); -extern void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr); +extern void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr, struct nfs_fattr *); extern void nfs_setsecurity(struct inode *inode, struct nfs_fattr *fattr, struct nfs4_label *label); extern struct nfs_open_context *get_nfs_open_context(struct nfs_open_context *ctx); -- cgit v1.2.3-59-g8ed1b From f5062003465c20cfe584d9129a463322ad5cf4ea Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 19:34:32 -0500 Subject: NFS: Set an attribute barrier on all updates Ensure that we update the attribute barrier even if there were no invalidations, provided that this value is newer than the old one. Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index 3a2d127de499..299bf7171a4d 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1738,6 +1738,7 @@ static int nfs_update_inode(struct inode *inode, struct nfs_fattr *fattr) nfs_inc_stats(inode, NFSIOS_ATTRINVALIDATE); nfsi->attrtimeo = NFS_MINATTRTIMEO(inode); nfsi->attrtimeo_timestamp = now; + /* Set barrier to be more recent than all outstanding updates */ nfsi->attr_gencount = nfs_inc_attr_generation_counter(); } else { if (!time_in_range_open(now, nfsi->attrtimeo_timestamp, nfsi->attrtimeo_timestamp + nfsi->attrtimeo)) { @@ -1745,6 +1746,9 @@ static int nfs_update_inode(struct inode *inode, struct nfs_fattr *fattr) nfsi->attrtimeo = NFS_MAXATTRTIMEO(inode); nfsi->attrtimeo_timestamp = now; } + /* Set the barrier to be more recent than this fattr */ + if ((long)fattr->gencount - (long)nfsi->attr_gencount > 0) + nfsi->attr_gencount = fattr->gencount; } invalid &= ~NFS_INO_INVALID_ATTR; /* Don't invalidate the data if we were to blame */ -- cgit v1.2.3-59-g8ed1b From a08a8cd375db9769588257e7782f6b6b68561b88 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 17:36:09 -0500 Subject: NFS: Add attribute update barriers to NFS writebacks Ensure that other operations that race with our write RPC calls cannot revert the file size updates that were made on the server. Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 25 ++++++++++++++++++++++--- fs/nfs/internal.h | 1 + fs/nfs/nfs3proc.c | 2 +- fs/nfs/nfs4proc.c | 2 +- fs/nfs/proc.c | 4 +--- fs/nfs/write.c | 30 ++++++++++++++++++++++++++++++ include/linux/nfs_fs.h | 1 + 7 files changed, 57 insertions(+), 8 deletions(-) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index 299bf7171a4d..ff9a6795da46 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1491,7 +1491,7 @@ int nfs_post_op_update_inode(struct inode *inode, struct nfs_fattr *fattr) EXPORT_SYMBOL_GPL(nfs_post_op_update_inode); /** - * nfs_post_op_update_inode_force_wcc - try to update the inode attribute cache + * nfs_post_op_update_inode_force_wcc_locked - update the inode attribute cache * @inode - pointer to inode * @fattr - updated attributes * @@ -1501,11 +1501,10 @@ EXPORT_SYMBOL_GPL(nfs_post_op_update_inode); * * This function is mainly designed to be used by the ->write_done() functions. */ -int nfs_post_op_update_inode_force_wcc(struct inode *inode, struct nfs_fattr *fattr) +int nfs_post_op_update_inode_force_wcc_locked(struct inode *inode, struct nfs_fattr *fattr) { int status; - spin_lock(&inode->i_lock); /* Don't do a WCC update if these attributes are already stale */ if ((fattr->valid & NFS_ATTR_FATTR) == 0 || !nfs_inode_attrs_need_update(inode, fattr)) { @@ -1537,6 +1536,26 @@ int nfs_post_op_update_inode_force_wcc(struct inode *inode, struct nfs_fattr *fa } out_noforce: status = nfs_post_op_update_inode_locked(inode, fattr); + return status; +} + +/** + * nfs_post_op_update_inode_force_wcc - try to update the inode attribute cache + * @inode - pointer to inode + * @fattr - updated attributes + * + * After an operation that has changed the inode metadata, mark the + * attribute cache as being invalid, then try to update it. Fake up + * weak cache consistency data, if none exist. + * + * This function is mainly designed to be used by the ->write_done() functions. + */ +int nfs_post_op_update_inode_force_wcc(struct inode *inode, struct nfs_fattr *fattr) +{ + int status; + + spin_lock(&inode->i_lock); + status = nfs_post_op_update_inode_force_wcc_locked(inode, fattr); spin_unlock(&inode->i_lock); return status; } diff --git a/fs/nfs/internal.h b/fs/nfs/internal.h index b802fb3a2d99..9e6475bc5ba2 100644 --- a/fs/nfs/internal.h +++ b/fs/nfs/internal.h @@ -459,6 +459,7 @@ void nfs_mark_request_commit(struct nfs_page *req, struct nfs_commit_info *cinfo, u32 ds_commit_idx); int nfs_write_need_commit(struct nfs_pgio_header *); +void nfs_writeback_update_inode(struct nfs_pgio_header *hdr); int nfs_generic_commit_list(struct inode *inode, struct list_head *head, int how, struct nfs_commit_info *cinfo); void nfs_retry_commit(struct list_head *page_list, diff --git a/fs/nfs/nfs3proc.c b/fs/nfs/nfs3proc.c index 11109a137c0c..1f11d2533ee4 100644 --- a/fs/nfs/nfs3proc.c +++ b/fs/nfs/nfs3proc.c @@ -834,7 +834,7 @@ static int nfs3_write_done(struct rpc_task *task, struct nfs_pgio_header *hdr) if (nfs3_async_handle_jukebox(task, inode)) return -EAGAIN; if (task->tk_status >= 0) - nfs_post_op_update_inode_force_wcc(inode, hdr->res.fattr); + nfs_writeback_update_inode(hdr); return 0; } diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index c499e02a58ca..b022e64b76a5 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -4237,7 +4237,7 @@ static int nfs4_write_done_cb(struct rpc_task *task, } if (task->tk_status >= 0) { renew_lease(NFS_SERVER(inode), hdr->timestamp); - nfs_post_op_update_inode_force_wcc(inode, &hdr->fattr); + nfs_writeback_update_inode(hdr); } return 0; } diff --git a/fs/nfs/proc.c b/fs/nfs/proc.c index 6202bc0f11bb..c63189acd052 100644 --- a/fs/nfs/proc.c +++ b/fs/nfs/proc.c @@ -609,10 +609,8 @@ static int nfs_proc_pgio_rpc_prepare(struct rpc_task *task, static int nfs_write_done(struct rpc_task *task, struct nfs_pgio_header *hdr) { - struct inode *inode = hdr->inode; - if (task->tk_status >= 0) - nfs_post_op_update_inode_force_wcc(inode, hdr->res.fattr); + nfs_writeback_update_inode(hdr); return 0; } diff --git a/fs/nfs/write.c b/fs/nfs/write.c index 595d81e354d1..849ed784d6ac 100644 --- a/fs/nfs/write.c +++ b/fs/nfs/write.c @@ -1377,6 +1377,36 @@ static int nfs_should_remove_suid(const struct inode *inode) return 0; } +static void nfs_writeback_check_extend(struct nfs_pgio_header *hdr, + struct nfs_fattr *fattr) +{ + struct nfs_pgio_args *argp = &hdr->args; + struct nfs_pgio_res *resp = &hdr->res; + + if (!(fattr->valid & NFS_ATTR_FATTR_SIZE)) + return; + if (argp->offset + resp->count != fattr->size) + return; + if (nfs_size_to_loff_t(fattr->size) < i_size_read(hdr->inode)) + return; + /* Set attribute barrier */ + nfs_fattr_set_barrier(fattr); +} + +void nfs_writeback_update_inode(struct nfs_pgio_header *hdr) +{ + struct nfs_fattr *fattr = hdr->res.fattr; + struct inode *inode = hdr->inode; + + if (fattr == NULL) + return; + spin_lock(&inode->i_lock); + nfs_writeback_check_extend(hdr, fattr); + nfs_post_op_update_inode_force_wcc_locked(inode, fattr); + spin_unlock(&inode->i_lock); +} +EXPORT_SYMBOL_GPL(nfs_writeback_update_inode); + /* * This function is called when the WRITE call is complete. */ diff --git a/include/linux/nfs_fs.h b/include/linux/nfs_fs.h index f26e64e0aff8..59b1516b9fd4 100644 --- a/include/linux/nfs_fs.h +++ b/include/linux/nfs_fs.h @@ -343,6 +343,7 @@ extern struct inode *nfs_fhget(struct super_block *, struct nfs_fh *, extern int nfs_refresh_inode(struct inode *, struct nfs_fattr *); extern int nfs_post_op_update_inode(struct inode *inode, struct nfs_fattr *fattr); extern int nfs_post_op_update_inode_force_wcc(struct inode *inode, struct nfs_fattr *fattr); +extern int nfs_post_op_update_inode_force_wcc_locked(struct inode *inode, struct nfs_fattr *fattr); extern int nfs_getattr(struct vfsmount *, struct dentry *, struct kstat *); extern void nfs_access_add_cache(struct inode *, struct nfs_access_entry *); extern void nfs_access_set_mask(struct nfs_access_entry *, u32); -- cgit v1.2.3-59-g8ed1b From 8f8ba1d739b7047e2e1d91735716af2799ff2b1e Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 17:54:58 -0500 Subject: NFSv4: Add attribute update barriers to delegreturn and pNFS layoutcommit Ensure that other operations that race with delegreturn and layoutcommit cannot revert the attribute updates that were made on the server. Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index ff9a6795da46..cd094d652199 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1555,6 +1555,7 @@ int nfs_post_op_update_inode_force_wcc(struct inode *inode, struct nfs_fattr *fa int status; spin_lock(&inode->i_lock); + nfs_fattr_set_barrier(fattr); status = nfs_post_op_update_inode_force_wcc_locked(inode, fattr); spin_unlock(&inode->i_lock); return status; -- cgit v1.2.3-59-g8ed1b From 00fb4c9f8421c9aac3947d36ffe8e049b95f7ab1 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 17:57:14 -0500 Subject: NFS: Remove size hack in nfs_inode_attrs_need_update() Prior to this patch, we used to always OK attribute updates that extended the file size on the assumption that we might be performing writeback. Now that we have attribute barriers to protect the writeback related updates, we should remove this hack, as it can cause truncate() operations to apparently be reverted if/when a readahead or getattr RPC call races with our on-the-wire SETATTR. Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 8 -------- 1 file changed, 8 deletions(-) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index cd094d652199..fef65d1e024e 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1238,13 +1238,6 @@ static int nfs_ctime_need_update(const struct inode *inode, const struct nfs_fat return timespec_compare(&fattr->ctime, &inode->i_ctime) > 0; } -static int nfs_size_need_update(const struct inode *inode, const struct nfs_fattr *fattr) -{ - if (!(fattr->valid & NFS_ATTR_FATTR_SIZE)) - return 0; - return nfs_size_to_loff_t(fattr->size) > i_size_read(inode); -} - static atomic_long_t nfs_attr_generation_counter; static unsigned long nfs_read_attr_generation_counter(void) @@ -1393,7 +1386,6 @@ static int nfs_inode_attrs_need_update(const struct inode *inode, const struct n return ((long)fattr->gencount - (long)nfsi->attr_gencount) > 0 || nfs_ctime_need_update(inode, fattr) || - nfs_size_need_update(inode, fattr) || ((long)nfsi->attr_gencount - (long)nfs_read_attr_generation_counter() > 0); } -- cgit v1.2.3-59-g8ed1b From 92d64e47b67b5e7fe1b5358402ab222a32ec3479 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 19:48:26 -0500 Subject: NFS: Fix nfs_post_op_update_inode() to set an attribute barrier nfs_post_op_update_inode() is called after a self-induced attribute update. Ensure that it also sets the barrier. Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index fef65d1e024e..c66c1df467f4 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1475,6 +1475,7 @@ int nfs_post_op_update_inode(struct inode *inode, struct nfs_fattr *fattr) int status; spin_lock(&inode->i_lock); + nfs_fattr_set_barrier(fattr); status = nfs_post_op_update_inode_locked(inode, fattr); spin_unlock(&inode->i_lock); -- cgit v1.2.3-59-g8ed1b From 3235b40303b6f609c446275d0e7f6f9f4fe94156 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 19:52:06 -0500 Subject: NFSv4: Set a barrier in the update_changeattr() helper Ensure that we don't regress the changes that were made to the directory. Signed-off-by: Trond Myklebust Tested-by: Chuck Lever --- fs/nfs/inode.c | 1 + fs/nfs/nfs4proc.c | 1 + 2 files changed, 2 insertions(+) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index c66c1df467f4..5026c44a98e1 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1249,6 +1249,7 @@ unsigned long nfs_inc_attr_generation_counter(void) { return atomic_long_inc_return(&nfs_attr_generation_counter); } +EXPORT_SYMBOL_GPL(nfs_inc_attr_generation_counter); void nfs_fattr_init(struct nfs_fattr *fattr) { diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index b022e64b76a5..a211daf58c32 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -901,6 +901,7 @@ static void update_changeattr(struct inode *dir, struct nfs4_change_info *cinfo) if (!cinfo->atomic || cinfo->before != dir->i_version) nfs_force_lookup_revalidate(dir); dir->i_version = cinfo->after; + nfsi->attr_gencount = nfs_inc_attr_generation_counter(); nfs_fscache_invalidate(dir); spin_unlock(&dir->i_lock); } -- cgit v1.2.3-59-g8ed1b From 6c441c254eea2354d686be7f5544bcd79fb6a61f Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Sun, 22 Feb 2015 16:35:36 -0500 Subject: NFS: Don't invalidate a submounted dentry in nfs_prime_dcache() If we're traversing a directory which contains a submounted filesystem, or one that has a referral, the NFS server that is processing the READDIR request will often return information for the underlying (mounted-on) directory. It may, or may not, also return filehandle information. If this happens, and the lookup in nfs_prime_dcache() returns the dentry for the submounted directory, the filehandle comparison will fail, and we call d_invalidate(). Post-commit 8ed936b5671bf ("vfs: Lazily remove mounts on unlinked files and directories."), this means the entire subtree is unmounted. The following minimal patch addresses this problem by punting on the invalidation if there is a submount. Kudos to Neil Brown for having tracked down this issue (see link). Reported-by: Nix Link: http://lkml.kernel.org/r/87iofju9ht.fsf@spindle.srvr.nix Cc: stable@vger.kernel.org # 3.18+ Signed-off-by: Trond Myklebust --- fs/nfs/dir.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/fs/nfs/dir.c b/fs/nfs/dir.c index 9b0c55cb2a2e..4ad7fff9ccaf 100644 --- a/fs/nfs/dir.c +++ b/fs/nfs/dir.c @@ -469,6 +469,8 @@ void nfs_prime_dcache(struct dentry *parent, struct nfs_entry *entry) struct inode *inode; int status; + if (!(entry->fattr->valid & NFS_ATTR_FATTR_FSID)) + return; if (filename.name[0] == '.') { if (filename.len == 1) return; @@ -479,6 +481,10 @@ void nfs_prime_dcache(struct dentry *parent, struct nfs_entry *entry) dentry = d_lookup(parent, &filename); if (dentry != NULL) { + /* Is there a mountpoint here? If so, just exit */ + if (!nfs_fsid_equal(&NFS_SB(dentry->d_sb)->fsid, + &entry->fattr->fsid)) + goto out; if (nfs_same_file(dentry, entry)) { nfs_set_verifier(dentry, nfs_save_change_attribute(dir)); status = nfs_refresh_inode(dentry->d_inode, entry->fattr); -- cgit v1.2.3-59-g8ed1b From 1ae04b252351188cfa66af1b8b0628512a72dd7b Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Mon, 23 Feb 2015 16:15:00 -0500 Subject: NFSv3: Use the readdir fileid as the mounted-on-fileid When we call readdirplus, set the fileid normally returned by readdir as the mounted-on-fileid, since that is commonly the case if there is a mountpoint. To ensure that we get it right, we only set the flag if the readdir fileid differs from the one returned in the readdirplus attributes. This again means that we can avoid the issues described in commit 2ef47eb1aee17 ("NFS: Fix use of nfs_attr_use_mounted_on_fileid()"), which only fixed NFSv4. Signed-off-by: Trond Myklebust --- fs/nfs/nfs3xdr.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/fs/nfs/nfs3xdr.c b/fs/nfs/nfs3xdr.c index 2a932fdc57cb..53852a4bd88b 100644 --- a/fs/nfs/nfs3xdr.c +++ b/fs/nfs/nfs3xdr.c @@ -1987,6 +1987,11 @@ int nfs3_decode_dirent(struct xdr_stream *xdr, struct nfs_entry *entry, if (entry->fattr->valid & NFS_ATTR_FATTR_V3) entry->d_type = nfs_umode_to_dtype(entry->fattr->mode); + if (entry->fattr->fileid != entry->ino) { + entry->fattr->mounted_on_fileid = entry->ino; + entry->fattr->valid |= NFS_ATTR_FATTR_MOUNTED_ON_FILEID; + } + /* In fact, a post_op_fh3: */ p = xdr_inline_decode(xdr, 4); if (unlikely(p == NULL)) -- cgit v1.2.3-59-g8ed1b From fa9233699cc1dc236f4cf42245d13e40966938c5 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Mon, 23 Feb 2015 18:51:32 -0500 Subject: NFS: Don't require a filehandle to refresh the inode in nfs_prime_dcache() If the server does not return a valid set of attributes that we can use to either create a file or refresh the inode, then there is no value in calling nfs_prime_dcache(). However if we're just refreshing the inode using the attributes that the server returned, then it shouldn't matter whether or not we have a filehandle, as long as we check the fsid+fileid combination. Signed-off-by: Trond Myklebust --- fs/nfs/dir.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) diff --git a/fs/nfs/dir.c b/fs/nfs/dir.c index 4ad7fff9ccaf..c19e16f0b2d0 100644 --- a/fs/nfs/dir.c +++ b/fs/nfs/dir.c @@ -408,14 +408,22 @@ static int xdr_decode(nfs_readdir_descriptor_t *desc, return 0; } +/* Match file and dirent using either filehandle or fileid + * Note: caller is responsible for checking the fsid + */ static int nfs_same_file(struct dentry *dentry, struct nfs_entry *entry) { + struct nfs_inode *nfsi; + if (dentry->d_inode == NULL) goto different; - if (nfs_compare_fh(entry->fh, NFS_FH(dentry->d_inode)) != 0) - goto different; - return 1; + + nfsi = NFS_I(dentry->d_inode); + if (entry->fattr->fileid == nfsi->fileid) + return 1; + if (nfs_compare_fh(entry->fh, &nfsi->fh) == 0) + return 1; different: return 0; } @@ -469,6 +477,8 @@ void nfs_prime_dcache(struct dentry *parent, struct nfs_entry *entry) struct inode *inode; int status; + if (!(entry->fattr->valid & NFS_ATTR_FATTR_FILEID)) + return; if (!(entry->fattr->valid & NFS_ATTR_FATTR_FSID)) return; if (filename.name[0] == '.') { -- cgit v1.2.3-59-g8ed1b From 7c0af9ffb7bb4e5355470fa60b3eb711ddf226fa Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 12:54:46 -0500 Subject: NFSv4: Don't call put_rpccred() under the rcu_read_lock() put_rpccred() can sleep. Fixes: 8f649c3762547 ("NFSv4: Fix the locking in nfs_inode_reclaim_delegation()") Cc: stable@vger.kernel.org # 2.6.35+ Signed-off-by: Trond Myklebust --- fs/nfs/delegation.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/nfs/delegation.c b/fs/nfs/delegation.c index a1f0685b42ff..2e37d8315d92 100644 --- a/fs/nfs/delegation.c +++ b/fs/nfs/delegation.c @@ -181,8 +181,8 @@ void nfs_inode_reclaim_delegation(struct inode *inode, struct rpc_cred *cred, clear_bit(NFS_DELEGATION_NEED_RECLAIM, &delegation->flags); spin_unlock(&delegation->lock); - put_rpccred(oldcred); rcu_read_unlock(); + put_rpccred(oldcred); trace_nfs4_reclaim_delegation(inode, res->delegation_type); } else { /* We appear to have raced with a delegation return. */ -- cgit v1.2.3-59-g8ed1b From aa91def41a7bb1fd65492934ce6bea19202b6080 Mon Sep 17 00:00:00 2001 From: Nicolas PLANEL Date: Sun, 1 Mar 2015 13:47:22 -0500 Subject: USB: ch341: set tty baud speed according to tty struct The ch341_set_baudrate() function initialize the device baud speed according to the value on priv->baud_rate. By default the ch341_open() set it to a hardcoded value (DEFAULT_BAUD_RATE 9600). Unfortunately, the tty_struct is not initialized with the same default value. (usually 56700) This means that the tty_struct and the device baud rate generator are not synchronized after opening the port. Fixup is done by calling ch341_set_termios() if tty exist. Remove unnecessary variable priv->baud_rate setup as it's already done by ch341_port_probe(). Remove unnecessary call to ch341_set_{handshake,baudrate}() in ch341_open() as there already called in ch341_configure() and ch341_set_termios() Signed-off-by: Nicolas PLANEL Signed-off-by: Johan Hovold --- drivers/usb/serial/ch341.c | 15 ++++++--------- 1 file changed, 6 insertions(+), 9 deletions(-) diff --git a/drivers/usb/serial/ch341.c b/drivers/usb/serial/ch341.c index 2d72aa3564a3..ede4f5fcfadd 100644 --- a/drivers/usb/serial/ch341.c +++ b/drivers/usb/serial/ch341.c @@ -84,6 +84,10 @@ struct ch341_private { u8 line_status; /* active status of modem control inputs */ }; +static void ch341_set_termios(struct tty_struct *tty, + struct usb_serial_port *port, + struct ktermios *old_termios); + static int ch341_control_out(struct usb_device *dev, u8 request, u16 value, u16 index) { @@ -309,19 +313,12 @@ static int ch341_open(struct tty_struct *tty, struct usb_serial_port *port) struct ch341_private *priv = usb_get_serial_port_data(port); int r; - priv->baud_rate = DEFAULT_BAUD_RATE; - r = ch341_configure(serial->dev, priv); if (r) goto out; - r = ch341_set_handshake(serial->dev, priv->line_control); - if (r) - goto out; - - r = ch341_set_baudrate(serial->dev, priv); - if (r) - goto out; + if (tty) + ch341_set_termios(tty, port, NULL); dev_dbg(&port->dev, "%s - submitting interrupt urb\n", __func__); r = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); -- cgit v1.2.3-59-g8ed1b From 42b696e808bbea3a4ebf8029e1965d2314612402 Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Tue, 24 Feb 2015 13:56:54 +0900 Subject: thermal: exynos: Fix wrong control of power down detection mode for Exynos7 This patch fixes the wrong control of PD_DET_EN (power down detection mode) for Exynos7 because exynos7_tmu_control() always enables the power down detection mode regardless 'on' parameter. Cc: Zhang Rui Cc: Eduardo Valentin Signed-off-by: Chanwoo Choi Tested-by: Abhilash Kesavan Signed-off-by: Lukasz Majewski --- drivers/thermal/samsung/exynos_tmu.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 1fc54ab911d2..1d30b0975651 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -682,6 +682,7 @@ static void exynos7_tmu_control(struct platform_device *pdev, bool on) if (on) { con |= (1 << EXYNOS_TMU_CORE_EN_SHIFT); + con |= (1 << EXYNOS7_PD_DET_EN_SHIFT); interrupt_en = (of_thermal_is_trip_valid(tz, 7) << EXYNOS7_TMU_INTEN_RISE7_SHIFT) | @@ -704,9 +705,9 @@ static void exynos7_tmu_control(struct platform_device *pdev, bool on) interrupt_en << EXYNOS_TMU_INTEN_FALL0_SHIFT; } else { con &= ~(1 << EXYNOS_TMU_CORE_EN_SHIFT); + con &= ~(1 << EXYNOS7_PD_DET_EN_SHIFT); interrupt_en = 0; /* Disable all interrupts */ } - con |= 1 << EXYNOS7_PD_DET_EN_SHIFT; writel(interrupt_en, data->base + EXYNOS7_TMU_REG_INTEN); writel(con, data->base + EXYNOS_TMU_REG_CONTROL); -- cgit v1.2.3-59-g8ed1b From 0fc83929d03c2e16cbcf6cf944bd5df8d829847f Mon Sep 17 00:00:00 2001 From: Lukasz Majewski Date: Thu, 5 Feb 2015 16:45:06 +0100 Subject: cpufreq: exynos: Use simple approach to asses if cpu cooling can be used Commit: e725d26c4857e5e41975b5e74e64ce6ab09a7121 provided possibility to use device tree to asses if cpu can be used as cooling device. Since the code was somewhat awkward, simpler approach has been proposed. Test HW: Exynos 4412 - Odroid U3. Suggested-by: Viresh Kumar Signed-off-by: Lukasz Majewski Acked-by: Viresh Kumar --- drivers/cpufreq/exynos-cpufreq.c | 21 ++++++--------------- 1 file changed, 6 insertions(+), 15 deletions(-) diff --git a/drivers/cpufreq/exynos-cpufreq.c b/drivers/cpufreq/exynos-cpufreq.c index 5e98c6b1f284..82d2fbb20f7e 100644 --- a/drivers/cpufreq/exynos-cpufreq.c +++ b/drivers/cpufreq/exynos-cpufreq.c @@ -159,7 +159,7 @@ static struct cpufreq_driver exynos_driver = { static int exynos_cpufreq_probe(struct platform_device *pdev) { - struct device_node *cpus, *np; + struct device_node *cpu0; int ret = -EINVAL; exynos_info = kzalloc(sizeof(*exynos_info), GFP_KERNEL); @@ -206,28 +206,19 @@ static int exynos_cpufreq_probe(struct platform_device *pdev) if (ret) goto err_cpufreq_reg; - cpus = of_find_node_by_path("/cpus"); - if (!cpus) { - pr_err("failed to find cpus node\n"); + cpu0 = of_get_cpu_node(0, NULL); + if (!cpu0) { + pr_err("failed to find cpu0 node\n"); return 0; } - np = of_get_next_child(cpus, NULL); - if (!np) { - pr_err("failed to find cpus child node\n"); - of_node_put(cpus); - return 0; - } - - if (of_find_property(np, "#cooling-cells", NULL)) { - cdev = of_cpufreq_cooling_register(np, + if (of_find_property(cpu0, "#cooling-cells", NULL)) { + cdev = of_cpufreq_cooling_register(cpu0, cpu_present_mask); if (IS_ERR(cdev)) pr_err("running cpufreq without cooling device: %ld\n", PTR_ERR(cdev)); } - of_node_put(np); - of_node_put(cpus); return 0; -- cgit v1.2.3-59-g8ed1b From 93c537affd5d2a7b2fcea4a1d608b011841d3c04 Mon Sep 17 00:00:00 2001 From: Lukasz Majewski Date: Tue, 24 Feb 2015 16:31:28 +0100 Subject: MAINTAINERS: Add entry for SAMSUNG THERMAL DRIVER This patch adds entry for SAMSUNG THERMAL DRIVER in the MAINTAINERS file. It has been agreed, that pull request are going to be sent to Eduardo Valentin. Signed-off-by: Lukasz Majewski Acked-by: Eduardo Valentin --- MAINTAINERS | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index ddc5a8cf9a8a..be837a0d2280 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8481,6 +8481,14 @@ S: Supported L: netdev@vger.kernel.org F: drivers/net/ethernet/samsung/sxgbe/ +SAMSUNG THERMAL DRIVER +M: Lukasz Majewski +L: linux-pm@vger.kernel.org +L: linux-samsung-soc@vger.kernel.org +S: Supported +T: https://github.com/lmajewski/linux-samsung-thermal.git +F: drivers/thermal/samsung/ + SAMSUNG USB2 PHY DRIVER M: Kamil Debski L: linux-kernel@vger.kernel.org -- cgit v1.2.3-59-g8ed1b From d7a6fe015b2abe33565538a3faf757e095e094e7 Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Tue, 6 Jan 2015 12:14:32 +0100 Subject: ASoC: sam9g20_wm8731: drop machine_is_xxx Atmel based boards can now only be used with device tree. Drop non DT initialization. Signed-off-by: Alexandre Belloni Signed-off-by: Mark Brown --- sound/soc/atmel/sam9g20_wm8731.c | 68 ++++++++++++++++++---------------------- 1 file changed, 31 insertions(+), 37 deletions(-) diff --git a/sound/soc/atmel/sam9g20_wm8731.c b/sound/soc/atmel/sam9g20_wm8731.c index f5ad214663f9..8de836165cf2 100644 --- a/sound/soc/atmel/sam9g20_wm8731.c +++ b/sound/soc/atmel/sam9g20_wm8731.c @@ -46,8 +46,6 @@ #include #include -#include - #include "../codecs/wm8731.h" #include "atmel-pcm.h" #include "atmel_ssc_dai.h" @@ -171,9 +169,7 @@ static int at91sam9g20ek_audio_probe(struct platform_device *pdev) int ret; if (!np) { - if (!(machine_is_at91sam9g20ek() || - machine_is_at91sam9g20ek_2mmc())) - return -ENODEV; + return -ENODEV; } ret = atmel_ssc_set_audio(0); @@ -210,39 +206,37 @@ static int at91sam9g20ek_audio_probe(struct platform_device *pdev) card->dev = &pdev->dev; /* Parse device node info */ - if (np) { - ret = snd_soc_of_parse_card_name(card, "atmel,model"); - if (ret) - goto err; - - ret = snd_soc_of_parse_audio_routing(card, - "atmel,audio-routing"); - if (ret) - goto err; - - /* Parse codec info */ - at91sam9g20ek_dai.codec_name = NULL; - codec_np = of_parse_phandle(np, "atmel,audio-codec", 0); - if (!codec_np) { - dev_err(&pdev->dev, "codec info missing\n"); - return -EINVAL; - } - at91sam9g20ek_dai.codec_of_node = codec_np; - - /* Parse dai and platform info */ - at91sam9g20ek_dai.cpu_dai_name = NULL; - at91sam9g20ek_dai.platform_name = NULL; - cpu_np = of_parse_phandle(np, "atmel,ssc-controller", 0); - if (!cpu_np) { - dev_err(&pdev->dev, "dai and pcm info missing\n"); - return -EINVAL; - } - at91sam9g20ek_dai.cpu_of_node = cpu_np; - at91sam9g20ek_dai.platform_of_node = cpu_np; - - of_node_put(codec_np); - of_node_put(cpu_np); + ret = snd_soc_of_parse_card_name(card, "atmel,model"); + if (ret) + goto err; + + ret = snd_soc_of_parse_audio_routing(card, + "atmel,audio-routing"); + if (ret) + goto err; + + /* Parse codec info */ + at91sam9g20ek_dai.codec_name = NULL; + codec_np = of_parse_phandle(np, "atmel,audio-codec", 0); + if (!codec_np) { + dev_err(&pdev->dev, "codec info missing\n"); + return -EINVAL; + } + at91sam9g20ek_dai.codec_of_node = codec_np; + + /* Parse dai and platform info */ + at91sam9g20ek_dai.cpu_dai_name = NULL; + at91sam9g20ek_dai.platform_name = NULL; + cpu_np = of_parse_phandle(np, "atmel,ssc-controller", 0); + if (!cpu_np) { + dev_err(&pdev->dev, "dai and pcm info missing\n"); + return -EINVAL; } + at91sam9g20ek_dai.cpu_of_node = cpu_np; + at91sam9g20ek_dai.platform_of_node = cpu_np; + + of_node_put(codec_np); + of_node_put(cpu_np); ret = snd_soc_register_card(card); if (ret) { -- cgit v1.2.3-59-g8ed1b From b6d1778bc5485c55c6f5194b8b2ea84c0ce5adad Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 26 Feb 2015 11:26:34 +0100 Subject: dmaengine: shdma: Move DMA stop to (runtime) suspend callbacks During system reboot, the sh-dma-engine device may be runtime-suspended, causing a crash: Unhandled fault: imprecise external abort (0x1406) at 0x0002c02c Internal error: : 1406 [#1] SMP ARM ... PC is at sh_dmae_ctl_stop+0x28/0x64 LR is at sh_dmae_ctl_stop+0x24/0x64 If the sh-dma-engine is runtime-suspended, its module clock is turned off, and its registers cannot be accessed. To fix this, move the call to sh_dmae_ctl_stop(), which touches the DMAOR register, to the sh_dmae_suspend() and sh_dmae_runtime_suspend() callbacks. This makes PM operations more symmetric, as both sh_dmae_resume() and sh_dmae_runtime_resume() already call sh_dmae_rst() to re-initialize the DMAOR register. Remove sh_dmae_shutdown(), as it became empty. Signed-off-by: Geert Uytterhoeven Reviewed-by: Ulf Hansson Signed-off-by: Vinod Koul --- drivers/dma/sh/shdmac.c | 15 +++++++-------- 1 file changed, 7 insertions(+), 8 deletions(-) diff --git a/drivers/dma/sh/shdmac.c b/drivers/dma/sh/shdmac.c index b2431aa30033..9f1d4c7dbab8 100644 --- a/drivers/dma/sh/shdmac.c +++ b/drivers/dma/sh/shdmac.c @@ -582,15 +582,12 @@ static void sh_dmae_chan_remove(struct sh_dmae_device *shdev) } } -static void sh_dmae_shutdown(struct platform_device *pdev) -{ - struct sh_dmae_device *shdev = platform_get_drvdata(pdev); - sh_dmae_ctl_stop(shdev); -} - #ifdef CONFIG_PM static int sh_dmae_runtime_suspend(struct device *dev) { + struct sh_dmae_device *shdev = dev_get_drvdata(dev); + + sh_dmae_ctl_stop(shdev); return 0; } @@ -605,6 +602,9 @@ static int sh_dmae_runtime_resume(struct device *dev) #ifdef CONFIG_PM_SLEEP static int sh_dmae_suspend(struct device *dev) { + struct sh_dmae_device *shdev = dev_get_drvdata(dev); + + sh_dmae_ctl_stop(shdev); return 0; } @@ -929,13 +929,12 @@ static int sh_dmae_remove(struct platform_device *pdev) } static struct platform_driver sh_dmae_driver = { - .driver = { + .driver = { .pm = &sh_dmae_pm, .name = SH_DMAE_DRV_NAME, .of_match_table = sh_dmae_of_match, }, .remove = sh_dmae_remove, - .shutdown = sh_dmae_shutdown, }; static int __init sh_dmae_init(void) -- cgit v1.2.3-59-g8ed1b From f5956fafb00afab474c3886b6297f9b5e7aff722 Mon Sep 17 00:00:00 2001 From: Or Gerlitz Date: Mon, 2 Mar 2015 18:22:15 +0200 Subject: net/mlx4_core: Fix wrong mask and error flow for the update-qp command The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS) of the update-qp command was defined twice (using enum value and pre-processor define directive) and wrong. The return value of the call to mlx4_update_qp() from within the SRIOV resource-tracker was wrongly voided down. Fix both issues. issue: none Fixes: 09e05c3f78e9 ('net/mlx4: Set vlan stripping policy by the right command') Fixes: ce8d9e0d6746 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support') Signed-off-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/qp.c | 1 - drivers/net/ethernet/mellanox/mlx4/resource_tracker.c | 9 ++++++--- include/linux/mlx4/qp.h | 2 +- 3 files changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlx4/qp.c b/drivers/net/ethernet/mellanox/mlx4/qp.c index 2bb8553bd905..eda29dbbfcd2 100644 --- a/drivers/net/ethernet/mellanox/mlx4/qp.c +++ b/drivers/net/ethernet/mellanox/mlx4/qp.c @@ -412,7 +412,6 @@ err_icm: EXPORT_SYMBOL_GPL(mlx4_qp_alloc); -#define MLX4_UPDATE_QP_SUPPORTED_ATTRS MLX4_UPDATE_QP_SMAC int mlx4_update_qp(struct mlx4_dev *dev, u32 qpn, enum mlx4_update_qp_attr attr, struct mlx4_update_qp_params *params) diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index 486e3d26cd4a..d97ca88c55b5 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -713,7 +713,7 @@ static int update_vport_qp_param(struct mlx4_dev *dev, struct mlx4_vport_oper_state *vp_oper; struct mlx4_priv *priv; u32 qp_type; - int port; + int port, err = 0; port = (qpc->pri_path.sched_queue & 0x40) ? 2 : 1; priv = mlx4_priv(dev); @@ -738,7 +738,9 @@ static int update_vport_qp_param(struct mlx4_dev *dev, } else { struct mlx4_update_qp_params params = {.flags = 0}; - mlx4_update_qp(dev, qpn, MLX4_UPDATE_QP_VSD, ¶ms); + err = mlx4_update_qp(dev, qpn, MLX4_UPDATE_QP_VSD, ¶ms); + if (err) + goto out; } } @@ -773,7 +775,8 @@ static int update_vport_qp_param(struct mlx4_dev *dev, qpc->pri_path.feup |= MLX4_FSM_FORCE_ETH_SRC_MAC; qpc->pri_path.grh_mylmc = (0x80 & qpc->pri_path.grh_mylmc) + vp_oper->mac_idx; } - return 0; +out: + return err; } static int mpt_mask(struct mlx4_dev *dev) diff --git a/include/linux/mlx4/qp.h b/include/linux/mlx4/qp.h index 2bbc62aa818a..551f85456c11 100644 --- a/include/linux/mlx4/qp.h +++ b/include/linux/mlx4/qp.h @@ -427,7 +427,7 @@ struct mlx4_wqe_inline_seg { enum mlx4_update_qp_attr { MLX4_UPDATE_QP_SMAC = 1 << 0, - MLX4_UPDATE_QP_VSD = 1 << 2, + MLX4_UPDATE_QP_VSD = 1 << 1, MLX4_UPDATE_QP_SUPPORTED_ATTRS = (1 << 2) - 1 }; -- cgit v1.2.3-59-g8ed1b From 1037ebbbd262227a91dfdd558159e345d4edf6b7 Mon Sep 17 00:00:00 2001 From: Ido Shamay Date: Mon, 2 Mar 2015 18:22:16 +0200 Subject: net/mlx4_en: Disbale GRO for incoming loopback/selftest packets Packets which are sent from the selftest (ethtool) flow, should not be passed to GRO stack but rather dropped by the driver after validation. To achieve that, we disable GRO for the duration of the selftest. Fixes: dd65beac48a5 ("net/mlx4_en: Extend usage of napi_gro_frags") Reported-by: Carol Soto Signed-off-by: Ido Shamay Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_selftest.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/mellanox/mlx4/en_selftest.c b/drivers/net/ethernet/mellanox/mlx4/en_selftest.c index 2d8ee66138e8..a61009f4b2df 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_selftest.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_selftest.c @@ -81,12 +81,14 @@ static int mlx4_en_test_loopback(struct mlx4_en_priv *priv) { u32 loopback_ok = 0; int i; - + bool gro_enabled; priv->loopback_ok = 0; priv->validate_loopback = 1; + gro_enabled = priv->dev->features & NETIF_F_GRO; mlx4_en_update_loopback_state(priv->dev, priv->dev->features); + priv->dev->features &= ~NETIF_F_GRO; /* xmit */ if (mlx4_en_test_loopback_xmit(priv)) { @@ -108,6 +110,10 @@ static int mlx4_en_test_loopback(struct mlx4_en_priv *priv) mlx4_en_test_loopback_exit: priv->validate_loopback = 0; + + if (gro_enabled) + priv->dev->features |= NETIF_F_GRO; + mlx4_en_update_loopback_state(priv->dev, priv->dev->features); return !loopback_ok; } -- cgit v1.2.3-59-g8ed1b From dfcacc154fb38fdb2c243c3dbbdc1f26a64cedc8 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Mon, 2 Mar 2015 22:25:37 +0100 Subject: cpuidle: Clean up fallback handling in cpuidle_idle_call() Move the fallback code path in cpuidle_idle_call() to the end of the function to avoid jumping to a label in an if () branch. Signed-off-by: Rafael J. Wysocki --- kernel/sched/idle.c | 29 +++++++++++++++-------------- 1 file changed, 15 insertions(+), 14 deletions(-) diff --git a/kernel/sched/idle.c b/kernel/sched/idle.c index f59198bda1bf..84b93b68482a 100644 --- a/kernel/sched/idle.c +++ b/kernel/sched/idle.c @@ -124,20 +124,8 @@ static void cpuidle_idle_call(void) * Fall back to the default arch idle method on errors. */ next_state = cpuidle_select(drv, dev); - if (next_state < 0) { -use_default: - /* - * We can't use the cpuidle framework, let's use the default - * idle routine. - */ - if (current_clr_polling_and_test()) - local_irq_enable(); - else - arch_cpu_idle(); - - goto exit_idle; - } - + if (next_state < 0) + goto use_default; /* * The idle task must be scheduled, it is pointless to @@ -195,6 +183,19 @@ exit_idle: rcu_idle_exit(); start_critical_timings(); + return; + +use_default: + /* + * We can't use the cpuidle framework, let's use the default + * idle routine. + */ + if (current_clr_polling_and_test()) + local_irq_enable(); + else + arch_cpu_idle(); + + goto exit_idle; } /* -- cgit v1.2.3-59-g8ed1b From f563db4bdb8ef5ea73d0f5ea2b20384c10fbd617 Mon Sep 17 00:00:00 2001 From: Radim Krčmář Date: Fri, 27 Feb 2015 16:32:38 +0100 Subject: KVM: SVM: fix interrupt injection (apic->isr_count always 0) MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit In commit b4eef9b36db4, we started to use hwapic_isr_update() != NULL instead of kvm_apic_vid_enabled(vcpu->kvm). This didn't work because SVM had it defined and "apicv" path in apic_{set,clear}_isr() does not change apic->isr_count, because it should always be 1. The initial value of apic->isr_count was based on kvm_apic_vid_enabled(vcpu->kvm), which is always 0 for SVM, so KVM could have injected interrupts when it shouldn't. Fix it by implicitly setting SVM's hwapic_isr_update to NULL and make the initial isr_count depend on hwapic_isr_update() for good measure. Fixes: b4eef9b36db4 ("kvm: x86: vmx: NULL out hwapic_isr_update() in case of !enable_apicv") Reported-and-tested-by: Borislav Petkov Signed-off-by: Radim Krčmář Signed-off-by: Marcelo Tosatti --- arch/x86/kvm/lapic.c | 4 ++-- arch/x86/kvm/svm.c | 6 ------ 2 files changed, 2 insertions(+), 8 deletions(-) diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c index e55b5fc344eb..bd4e34de24c7 100644 --- a/arch/x86/kvm/lapic.c +++ b/arch/x86/kvm/lapic.c @@ -1572,7 +1572,7 @@ void kvm_lapic_reset(struct kvm_vcpu *vcpu) apic_set_reg(apic, APIC_TMR + 0x10 * i, 0); } apic->irr_pending = kvm_apic_vid_enabled(vcpu->kvm); - apic->isr_count = kvm_apic_vid_enabled(vcpu->kvm); + apic->isr_count = kvm_x86_ops->hwapic_isr_update ? 1 : 0; apic->highest_isr_cache = -1; update_divide_count(apic); atomic_set(&apic->lapic_timer.pending, 0); @@ -1782,7 +1782,7 @@ void kvm_apic_post_state_restore(struct kvm_vcpu *vcpu, update_divide_count(apic); start_apic_timer(apic); apic->irr_pending = true; - apic->isr_count = kvm_apic_vid_enabled(vcpu->kvm) ? + apic->isr_count = kvm_x86_ops->hwapic_isr_update ? 1 : count_vectors(apic->regs + APIC_ISR); apic->highest_isr_cache = -1; if (kvm_x86_ops->hwapic_irr_update) diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c index d319e0c24758..cc618c882f90 100644 --- a/arch/x86/kvm/svm.c +++ b/arch/x86/kvm/svm.c @@ -3649,11 +3649,6 @@ static void svm_load_eoi_exitmap(struct kvm_vcpu *vcpu, u64 *eoi_exit_bitmap) return; } -static void svm_hwapic_isr_update(struct kvm *kvm, int isr) -{ - return; -} - static void svm_sync_pir_to_irr(struct kvm_vcpu *vcpu) { return; @@ -4403,7 +4398,6 @@ static struct kvm_x86_ops svm_x86_ops = { .set_virtual_x2apic_mode = svm_set_virtual_x2apic_mode, .vm_has_apicv = svm_vm_has_apicv, .load_eoi_exitmap = svm_load_eoi_exitmap, - .hwapic_isr_update = svm_hwapic_isr_update, .sync_pir_to_irr = svm_sync_pir_to_irr, .set_tss_addr = svm_set_tss_addr, -- cgit v1.2.3-59-g8ed1b From 4d884fceaa2c838abb598778813e93f6d9fea723 Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Mon, 9 Feb 2015 17:17:43 +0000 Subject: Btrfs: fix fsync race leading to ordered extent memory leaks We can have multiple fsync operations against the same file during the same transaction and they can collect the same ordered extents while they don't complete (still accessible from the inode's ordered tree). If this happens, those ordered extents will never get their reference counts decremented to 0, leading to memory leaks and inode leaks (an iput for an ordered extent's inode is scheduled only when the ordered extent's refcount drops to 0). The following sequence diagram explains this race: CPU 1 CPU 2 btrfs_sync_file() btrfs_sync_file() mutex_lock(inode->i_mutex) btrfs_log_inode() btrfs_get_logged_extents() --> collects ordered extent X --> increments ordered extent X's refcount btrfs_submit_logged_extents() mutex_unlock(inode->i_mutex) mutex_lock(inode->i_mutex) btrfs_sync_log() btrfs_wait_logged_extents() --> list_del_init(&ordered->log_list) btrfs_log_inode() btrfs_get_logged_extents() --> Adds ordered extent X to logged_list because at this point: list_empty(&ordered->log_list) && test_bit(BTRFS_ORDERED_LOGGED, &ordered->flags) == 0 --> Increments ordered extent X's refcount --> check if ordered extent's io is finished or not, start it if necessary and wait for it to finish --> sets bit BTRFS_ORDERED_LOGGED on ordered extent X's flags and adds it to trans->ordered btrfs_sync_log() finishes btrfs_submit_logged_extents() btrfs_log_inode() finishes mutex_unlock(inode->i_mutex) btrfs_sync_file() finishes btrfs_sync_log() btrfs_wait_logged_extents() --> Sees ordered extent X has the bit BTRFS_ORDERED_LOGGED set in its flags --> X's refcount is untouched btrfs_sync_log() finishes btrfs_sync_file() finishes btrfs_commit_transaction() --> called by transaction kthread for e.g. btrfs_wait_pending_ordered() --> waits for ordered extent X to complete --> decrements ordered extent X's refcount by 1 only, corresponding to the increment done by the fsync task ran by CPU 1 In the scenario of the above diagram, after the transaction commit, the ordered extent will remain with a refcount of 1 forever, leaking the ordered extent structure and preventing the i_count of its inode from ever decreasing to 0, since the delayed iput is scheduled only when the ordered extent's refcount drops to 0, preventing the inode from ever being evicted by the VFS. Fix this by using the flag BTRFS_ORDERED_LOGGED differently. Use it to mean that an ordered extent is already being processed by an fsync call, which will attach it to the current transaction, preventing it from being collected by subsequent fsync operations against the same inode. This race was introduced with the following change (added in 3.19 and backported to stable 3.18 and 3.17): Btrfs: make sure logged extents complete in the current transaction V3 commit 50d9aa99bd35c77200e0e3dd7a72274f8304701f I ran into this issue while running xfstests/generic/113 in a loop, which failed about 1 out of 10 runs with the following warning in dmesg: [ 2612.440038] WARNING: CPU: 4 PID: 22057 at fs/btrfs/disk-io.c:3558 free_fs_root+0x36/0x133 [btrfs]() [ 2612.442810] Modules linked in: btrfs crc32c_generic xor raid6_pq nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscache sunrpc loop processor parport_pc parport psmouse therma l_sys i2c_piix4 serio_raw pcspkr evdev microcode button i2c_core ext4 crc16 jbd2 mbcache sd_mod sg sr_mod cdrom virtio_scsi ata_generic virtio_pci ata_piix virtio_ring libata virtio flo ppy e1000 scsi_mod [last unloaded: btrfs] [ 2612.452711] CPU: 4 PID: 22057 Comm: umount Tainted: G W 3.19.0-rc5-btrfs-next-4+ #1 [ 2612.454921] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014 [ 2612.457709] 0000000000000009 ffff8801342c3c78 ffffffff8142425e ffff88023ec8f2d8 [ 2612.459829] 0000000000000000 ffff8801342c3cb8 ffffffff81045308 ffff880046460000 [ 2612.461564] ffffffffa036da56 ffff88003d07b000 ffff880046460000 ffff880046460068 [ 2612.463163] Call Trace: [ 2612.463719] [] dump_stack+0x4c/0x65 [ 2612.464789] [] warn_slowpath_common+0xa1/0xbb [ 2612.466026] [] ? free_fs_root+0x36/0x133 [btrfs] [ 2612.467247] [] warn_slowpath_null+0x1a/0x1c [ 2612.468416] [] free_fs_root+0x36/0x133 [btrfs] [ 2612.469625] [] btrfs_drop_and_free_fs_root+0x93/0x9b [btrfs] [ 2612.471251] [] btrfs_free_fs_roots+0xa4/0xd6 [btrfs] [ 2612.472536] [] ? wait_for_completion+0x24/0x26 [ 2612.473742] [] close_ctree+0x1f3/0x33c [btrfs] [ 2612.475477] [] ? destroy_workqueue+0x148/0x1ba [ 2612.476695] [] btrfs_put_super+0x19/0x1b [btrfs] [ 2612.477911] [] generic_shutdown_super+0x73/0xef [ 2612.479106] [] kill_anon_super+0x13/0x1e [ 2612.480226] [] btrfs_kill_super+0x17/0x23 [btrfs] [ 2612.481471] [] deactivate_locked_super+0x3b/0x50 [ 2612.482686] [] deactivate_super+0x3f/0x43 [ 2612.483791] [] cleanup_mnt+0x59/0x78 [ 2612.484842] [] __cleanup_mnt+0x12/0x14 [ 2612.485900] [] task_work_run+0x8f/0xbc [ 2612.486960] [] do_notify_resume+0x5a/0x6b [ 2612.488083] [] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 2612.489333] [] int_signal+0x12/0x17 [ 2612.490353] ---[ end trace 54a960a6bdcb8d93 ]--- [ 2612.557253] VFS: Busy inodes after unmount of sdb. Self-destruct in 5 seconds. Have a nice day... Kmemleak confirmed the ordered extent leak (and btrfs inode specific structures such as delayed nodes): $ cat /sys/kernel/debug/kmemleak unreferenced object 0xffff880154290db0 (size 576): comm "btrfsck", pid 21980, jiffies 4295542503 (age 1273.412s) hex dump (first 32 bytes): 01 40 00 00 01 00 00 00 b0 1d f1 4e 01 88 ff ff .@.........N.... 00 00 00 00 00 00 00 00 c8 0d 29 54 01 88 ff ff ..........)T.... backtrace: [] kmemleak_update_trace+0x4c/0x6a [] radix_tree_node_alloc+0x6d/0x83 [] __radix_tree_create+0x109/0x190 [] radix_tree_insert+0x30/0xac [] btrfs_get_or_create_delayed_node+0x130/0x187 [btrfs] [] btrfs_delayed_delete_inode_ref+0x32/0xac [btrfs] [] __btrfs_unlink_inode+0xee/0x288 [btrfs] [] btrfs_unlink_inode+0x1e/0x40 [btrfs] [] btrfs_unlink+0x60/0x9b [btrfs] [] vfs_unlink+0x9c/0xed [] do_unlinkat+0x12c/0x1fa [] SyS_unlinkat+0x29/0x2b [] system_call_fastpath+0x12/0x17 [] 0xffffffffffffffff unreferenced object 0xffff88014ef11db0 (size 576): comm "rm", pid 22009, jiffies 4295542593 (age 1273.052s) hex dump (first 32 bytes): 02 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 c8 1d f1 4e 01 88 ff ff ...........N.... backtrace: [] kmemleak_update_trace+0x4c/0x6a [] radix_tree_node_alloc+0x6d/0x83 [] __radix_tree_create+0x109/0x190 [] radix_tree_insert+0x30/0xac [] btrfs_get_or_create_delayed_node+0x130/0x187 [btrfs] [] btrfs_delayed_delete_inode_ref+0x32/0xac [btrfs] [] __btrfs_unlink_inode+0xee/0x288 [btrfs] [] btrfs_unlink_inode+0x1e/0x40 [btrfs] [] btrfs_unlink+0x60/0x9b [btrfs] [] vfs_unlink+0x9c/0xed [] do_unlinkat+0x12c/0x1fa [] SyS_unlinkat+0x29/0x2b [] system_call_fastpath+0x12/0x17 [] 0xffffffffffffffff unreferenced object 0xffff8800336feda8 (size 584): comm "aio-stress", pid 22031, jiffies 4295543006 (age 1271.400s) hex dump (first 32 bytes): 00 40 3e 00 00 00 00 00 00 00 8f 42 00 00 00 00 .@>........B.... 00 00 01 00 00 00 00 00 00 00 01 00 00 00 00 00 ................ backtrace: [] create_object+0x172/0x29a [] kmemleak_alloc+0x25/0x41 [] kmemleak_alloc_recursive.constprop.52+0x16/0x18 [] kmem_cache_alloc+0xf7/0x198 [] __btrfs_add_ordered_extent+0x43/0x309 [btrfs] [] btrfs_add_ordered_extent_dio+0x12/0x14 [btrfs] [] btrfs_get_blocks_direct+0x3ef/0x571 [btrfs] [] do_blockdev_direct_IO+0x62a/0xb47 [] __blockdev_direct_IO+0x34/0x36 [] btrfs_direct_IO+0x16a/0x1e8 [btrfs] [] generic_file_direct_write+0xb8/0x12d [] btrfs_file_write_iter+0x24b/0x42f [btrfs] [] aio_run_iocb+0x2b7/0x32e [] do_io_submit+0x26e/0x2ff [] SyS_io_submit+0x10/0x12 [] system_call_fastpath+0x12/0x17 CC: # 3.19, 3.18 and 3.17 Signed-off-by: Filipe Manana Signed-off-by: Chris Mason --- fs/btrfs/ordered-data.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/fs/btrfs/ordered-data.c b/fs/btrfs/ordered-data.c index 534544e08f76..157cc54fc634 100644 --- a/fs/btrfs/ordered-data.c +++ b/fs/btrfs/ordered-data.c @@ -452,9 +452,7 @@ void btrfs_get_logged_extents(struct inode *inode, continue; if (entry_end(ordered) <= start) break; - if (!list_empty(&ordered->log_list)) - continue; - if (test_bit(BTRFS_ORDERED_LOGGED, &ordered->flags)) + if (test_and_set_bit(BTRFS_ORDERED_LOGGED, &ordered->flags)) continue; list_add(&ordered->log_list, logged_list); atomic_inc(&ordered->refs); @@ -511,8 +509,7 @@ void btrfs_wait_logged_extents(struct btrfs_trans_handle *trans, wait_event(ordered->wait, test_bit(BTRFS_ORDERED_IO_DONE, &ordered->flags)); - if (!test_and_set_bit(BTRFS_ORDERED_LOGGED, &ordered->flags)) - list_add_tail(&ordered->trans_list, &trans->ordered); + list_add_tail(&ordered->trans_list, &trans->ordered); spin_lock_irq(&log->log_extents_lock[index]); } spin_unlock_irq(&log->log_extents_lock[index]); -- cgit v1.2.3-59-g8ed1b From 0c0ef4bc842ba6b593bb94f9fb8b653fe18c5ed8 Mon Sep 17 00:00:00 2001 From: Josef Bacik Date: Thu, 12 Feb 2015 09:43:51 -0500 Subject: Btrfs: abort the transaction if we fail to update the free space cache inode Our gluster boxes were hitting a problem where they'd run out of space when updating the block group cache and therefore wouldn't be able to update the free space inode. This is a problem because this is how we invalidate the cache and protect ourselves from errors further down the stack, so if this fails we have to abort the transaction so we make sure we don't end up with stale free space cache. Thanks, Signed-off-by: Josef Bacik Signed-off-by: Chris Mason --- fs/btrfs/extent-tree.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index 28ce5c8004d4..92146a5afdc1 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -3208,6 +3208,8 @@ static int cache_save_setup(struct btrfs_block_group_cache *block_group, return 0; } + if (trans->aborted) + return 0; again: inode = lookup_free_space_inode(root, block_group, path); if (IS_ERR(inode) && PTR_ERR(inode) != -ENOENT) { @@ -3243,6 +3245,20 @@ again: */ BTRFS_I(inode)->generation = 0; ret = btrfs_update_inode(trans, root, inode); + if (ret) { + /* + * So theoretically we could recover from this, simply set the + * super cache generation to 0 so we know to invalidate the + * cache, but then we'd have to keep track of the block groups + * that fail this way so we know we _have_ to reset this cache + * before the next commit or risk reading stale cache. So to + * limit our exposure to horrible edge cases lets just abort the + * transaction, this only happens in really bad situations + * anyway. + */ + btrfs_abort_transaction(trans, root, ret); + goto out_put; + } WARN_ON(ret); if (i_size_read(inode) > 0) { -- cgit v1.2.3-59-g8ed1b From e8c1c76e804b18120e6977fc092769c043876212 Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Sun, 15 Feb 2015 22:38:54 +0000 Subject: Btrfs: add missing inode update when punching hole When punching a file hole if we endup only zeroing parts of a page, because the start offset isn't a multiple of the sector size or the start offset and length fall within the same page, we were not updating the inode item. This prevented an fsync from doing anything, if no other file changes happened in the current transaction, because the fields in btrfs_inode used to check if the inode needs to be fsync'ed weren't updated. This issue is easy to reproduce and the following excerpt from the xfstest case I made shows how to trigger it: _scratch_mkfs >> $seqres.full 2>&1 _init_flakey _mount_flakey # Create our test file. $XFS_IO_PROG -f -c "pwrite -S 0x22 -b 16K 0 16K" \ $SCRATCH_MNT/foo | _filter_xfs_io # Fsync the file, this makes btrfs update some btrfs inode specific fields # that are used to track if the inode needs to be written/updated to the fsync # log or not. After this fsync, the new values for those fields indicate that # a subsequent fsync does not need to touch the fsync log. $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo # Force a commit of the current transaction. After this point, any operation # that modifies the data or metadata of our file, should update those fields in # the btrfs inode with values that make the next fsync operation write to the # fsync log. sync # Punch a hole in our file. This small range affects only 1 page. # This made the btrfs hole punching implementation write only some zeroes in # one page, but it did not update the btrfs inode fields used to determine if # the next fsync needs to write to the fsync log. $XFS_IO_PROG -c "fpunch 8000 4K" $SCRATCH_MNT/foo # Another variation of the previously mentioned case. $XFS_IO_PROG -c "fpunch 15000 100" $SCRATCH_MNT/foo # Now fsync the file. This was a no-operation because the previous hole punch # operation didn't update the inode's fields mentioned before, so they remained # with the values they had after the first fsync - that is, they indicate that # it is not needed to write to fsync log. $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo echo "File content before:" od -t x1 $SCRATCH_MNT/foo # Simulate a crash/power loss. _load_flakey_table $FLAKEY_DROP_WRITES _unmount_flakey # Enable writes and mount the fs. This makes the fsync log replay code run. _load_flakey_table $FLAKEY_ALLOW_WRITES _mount_flakey # Because the last fsync didn't do anything, here the file content matched what # it was after the first fsync, before the holes were punched, and not what it # was after the holes were punched. echo "File content after:" od -t x1 $SCRATCH_MNT/foo This issue has been around since 2012, when the punch hole implementation was added, commit 2aaa66558172 ("Btrfs: add hole punching"). A test case for xfstests follows soon. Signed-off-by: Filipe Manana Reviewed-by: Liu Bo Signed-off-by: Chris Mason --- fs/btrfs/file.c | 31 ++++++++++++++++++++++++++++--- 1 file changed, 28 insertions(+), 3 deletions(-) diff --git a/fs/btrfs/file.c b/fs/btrfs/file.c index e4090259569b..b476e5645034 100644 --- a/fs/btrfs/file.c +++ b/fs/btrfs/file.c @@ -2276,6 +2276,8 @@ static int btrfs_punch_hole(struct inode *inode, loff_t offset, loff_t len) bool same_page; bool no_holes = btrfs_fs_incompat(root->fs_info, NO_HOLES); u64 ino_size; + bool truncated_page = false; + bool updated_inode = false; ret = btrfs_wait_ordered_range(inode, offset, len); if (ret) @@ -2307,13 +2309,18 @@ static int btrfs_punch_hole(struct inode *inode, loff_t offset, loff_t len) * entire page. */ if (same_page && len < PAGE_CACHE_SIZE) { - if (offset < ino_size) + if (offset < ino_size) { + truncated_page = true; ret = btrfs_truncate_page(inode, offset, len, 0); + } else { + ret = 0; + } goto out_only_mutex; } /* zero back part of the first page */ if (offset < ino_size) { + truncated_page = true; ret = btrfs_truncate_page(inode, offset, 0, 0); if (ret) { mutex_unlock(&inode->i_mutex); @@ -2349,6 +2356,7 @@ static int btrfs_punch_hole(struct inode *inode, loff_t offset, loff_t len) if (!ret) { /* zero the front end of the last page */ if (tail_start + tail_len < ino_size) { + truncated_page = true; ret = btrfs_truncate_page(inode, tail_start + tail_len, 0, 1); if (ret) @@ -2358,8 +2366,8 @@ static int btrfs_punch_hole(struct inode *inode, loff_t offset, loff_t len) } if (lockend < lockstart) { - mutex_unlock(&inode->i_mutex); - return 0; + ret = 0; + goto out_only_mutex; } while (1) { @@ -2507,6 +2515,7 @@ out_trans: trans->block_rsv = &root->fs_info->trans_block_rsv; ret = btrfs_update_inode(trans, root, inode); + updated_inode = true; btrfs_end_transaction(trans, root); btrfs_btree_balance_dirty(root); out_free: @@ -2516,6 +2525,22 @@ out: unlock_extent_cached(&BTRFS_I(inode)->io_tree, lockstart, lockend, &cached_state, GFP_NOFS); out_only_mutex: + if (!updated_inode && truncated_page && !ret && !err) { + /* + * If we only end up zeroing part of a page, we still need to + * update the inode item, so that all the time fields are + * updated as well as the necessary btrfs inode in memory fields + * for detecting, at fsync time, if the inode isn't yet in the + * log tree or it's there but not up to date. + */ + trans = btrfs_start_transaction(root, 1); + if (IS_ERR(trans)) { + err = PTR_ERR(trans); + } else { + err = btrfs_update_inode(trans, root, inode); + ret = btrfs_end_transaction(trans, root); + } + } mutex_unlock(&inode->i_mutex); if (ret && !err) err = ret; -- cgit v1.2.3-59-g8ed1b From 5dfe2be7ead15863fd7b3fcc8bd69e470fae2bec Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Mon, 23 Feb 2015 19:48:52 +0000 Subject: Btrfs: fix off-by-one logic error in btrfs_realloc_node The end_slot variable actually matches the number of pointers in the node and not the last slot (which is 'nritems - 1'). Therefore in order to check that the current slot in the for loop doesn't match the last one, the correct logic is to check if 'i' is less than 'end_slot - 1' and not 'end_slot - 2'. Fix this and set end_slot to be 'nritems - 1', as it's less confusing since the variable name implies it's inclusive rather then exclusive. Signed-off-by: Filipe Manana Signed-off-by: Chris Mason --- fs/btrfs/ctree.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c index 993642199326..6d67f32e648d 100644 --- a/fs/btrfs/ctree.c +++ b/fs/btrfs/ctree.c @@ -1645,14 +1645,14 @@ int btrfs_realloc_node(struct btrfs_trans_handle *trans, parent_nritems = btrfs_header_nritems(parent); blocksize = root->nodesize; - end_slot = parent_nritems; + end_slot = parent_nritems - 1; - if (parent_nritems == 1) + if (parent_nritems <= 1) return 0; btrfs_set_lock_blocking(parent); - for (i = start_slot; i < end_slot; i++) { + for (i = start_slot; i <= end_slot; i++) { int close = 1; btrfs_node_key(parent, &disk_key, i); @@ -1669,7 +1669,7 @@ int btrfs_realloc_node(struct btrfs_trans_handle *trans, other = btrfs_node_blockptr(parent, i - 1); close = close_blocks(blocknr, other, blocksize); } - if (!close && i < end_slot - 2) { + if (!close && i < end_slot) { other = btrfs_node_blockptr(parent, i + 1); close = close_blocks(blocknr, other, blocksize); } -- cgit v1.2.3-59-g8ed1b From 5cdf83edb8e41cad1ec8eab2d402b4f9d9eb7ee0 Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Mon, 23 Feb 2015 19:50:49 +0000 Subject: Btrfs: do not ignore errors from btrfs_lookup_xattr in do_setxattr The return value from btrfs_lookup_xattr() can be a pointer encoding an error, therefore deal with it. This fixes commit 5f5bc6b1e2d5 ("Btrfs: make xattr replace operations atomic"). Signed-off-by: Filipe Manana Signed-off-by: Chris Mason --- fs/btrfs/xattr.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/fs/btrfs/xattr.c b/fs/btrfs/xattr.c index 47b19465f0dc..883b93623bc5 100644 --- a/fs/btrfs/xattr.c +++ b/fs/btrfs/xattr.c @@ -111,6 +111,8 @@ static int do_setxattr(struct btrfs_trans_handle *trans, name, name_len, -1); if (!di && (flags & XATTR_REPLACE)) ret = -ENODATA; + else if (IS_ERR(di)) + ret = PTR_ERR(di); else if (di) ret = btrfs_delete_one_dir_name(trans, root, path, di); goto out; @@ -127,10 +129,12 @@ static int do_setxattr(struct btrfs_trans_handle *trans, ASSERT(mutex_is_locked(&inode->i_mutex)); di = btrfs_lookup_xattr(NULL, root, path, btrfs_ino(inode), name, name_len, 0); - if (!di) { + if (!di) ret = -ENODATA; + else if (IS_ERR(di)) + ret = PTR_ERR(di); + if (ret) goto out; - } btrfs_release_path(path); di = NULL; } -- cgit v1.2.3-59-g8ed1b From 1932b7be973b554ffe20a5bba6ffaed6fa995cdc Mon Sep 17 00:00:00 2001 From: David Sterba Date: Tue, 24 Feb 2015 18:57:18 +0100 Subject: btrfs: fix lost return value due to variable shadowing A block-local variable stores error code but btrfs_get_blocks_direct may not return it in the end as there's a ret defined in the function scope. CC: # 3.6+ Fixes: d187663ef24c ("Btrfs: lock extents as we map them in DIO") Signed-off-by: David Sterba Signed-off-by: Chris Mason --- fs/btrfs/inode.c | 1 - 1 file changed, 1 deletion(-) diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c index 8564d8ce03de..91a87f53be3c 100644 --- a/fs/btrfs/inode.c +++ b/fs/btrfs/inode.c @@ -7288,7 +7288,6 @@ static int btrfs_get_blocks_direct(struct inode *inode, sector_t iblock, ((BTRFS_I(inode)->flags & BTRFS_INODE_NODATACOW) && em->block_start != EXTENT_MAP_HOLE)) { int type; - int ret; u64 block_start, orig_start, orig_block_len, ram_bytes; if (test_bit(EXTENT_FLAG_PREALLOC, &em->flags)) -- cgit v1.2.3-59-g8ed1b From 84471e2429ed82fdbac0c56d5b2a18d450f99f6a Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Sat, 28 Feb 2015 22:29:22 +0000 Subject: Btrfs: incremental send, don't rename a directory too soon There's one more case where we can't issue a rename operation for a directory as soon as we process it. We used to delay directory renames only if they have some ancestor directory with a higher inode number that got renamed too, but there's another case where we need to delay the rename too - when a directory A is renamed to the old name of a directory B but that directory B has its rename delayed because it has now (in the send root) an ancestor with a higher inode number that was renamed. If we don't delay the directory rename in this case, the receiving end of the send stream will attempt to rename A to the old name of B before B got renamed to its new name, which results in a "directory not empty" error. So fix this by delaying directory renames for this case too. Steps to reproduce: $ mkfs.btrfs -f /dev/sdb $ mount /dev/sdb /mnt $ mkdir /mnt/a $ mkdir /mnt/b $ mkdir /mnt/c $ touch /mnt/a/file $ btrfs subvolume snapshot -r /mnt /mnt/snap1 $ mv /mnt/c /mnt/x $ mv /mnt/a /mnt/x/y $ mv /mnt/b /mnt/a $ btrfs subvolume snapshot -r /mnt /mnt/snap2 $ btrfs send /mnt/snap1 -f /tmp/1.send $ btrfs send -p /mnt/snap1 /mnt/snap2 -f /tmp/2.send $ mkfs.btrfs -f /dev/sdc $ mount /dev/sdc /mnt2 $ btrfs receive /mnt2 -f /tmp/1.send $ btrfs receive /mnt2 -f /tmp/2.send ERROR: rename b -> a failed. Directory not empty A test case for xfstests follows soon. Reported-by: Ames Cornish Signed-off-by: Filipe Manana Signed-off-by: Chris Mason --- fs/btrfs/send.c | 171 +++++++++++++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 156 insertions(+), 15 deletions(-) diff --git a/fs/btrfs/send.c b/fs/btrfs/send.c index fe5857223515..d6033f540cc7 100644 --- a/fs/btrfs/send.c +++ b/fs/btrfs/send.c @@ -230,6 +230,7 @@ struct pending_dir_move { u64 parent_ino; u64 ino; u64 gen; + bool is_orphan; struct list_head update_refs; }; @@ -2984,7 +2985,8 @@ static int add_pending_dir_move(struct send_ctx *sctx, u64 ino_gen, u64 parent_ino, struct list_head *new_refs, - struct list_head *deleted_refs) + struct list_head *deleted_refs, + const bool is_orphan) { struct rb_node **p = &sctx->pending_dir_moves.rb_node; struct rb_node *parent = NULL; @@ -2999,6 +3001,7 @@ static int add_pending_dir_move(struct send_ctx *sctx, pm->parent_ino = parent_ino; pm->ino = ino; pm->gen = ino_gen; + pm->is_orphan = is_orphan; INIT_LIST_HEAD(&pm->list); INIT_LIST_HEAD(&pm->update_refs); RB_CLEAR_NODE(&pm->node); @@ -3131,16 +3134,20 @@ static int apply_dir_move(struct send_ctx *sctx, struct pending_dir_move *pm) rmdir_ino = dm->rmdir_ino; free_waiting_dir_move(sctx, dm); - ret = get_first_ref(sctx->parent_root, pm->ino, - &parent_ino, &parent_gen, name); - if (ret < 0) - goto out; - - ret = get_cur_path(sctx, parent_ino, parent_gen, - from_path); - if (ret < 0) - goto out; - ret = fs_path_add_path(from_path, name); + if (pm->is_orphan) { + ret = gen_unique_name(sctx, pm->ino, + pm->gen, from_path); + } else { + ret = get_first_ref(sctx->parent_root, pm->ino, + &parent_ino, &parent_gen, name); + if (ret < 0) + goto out; + ret = get_cur_path(sctx, parent_ino, parent_gen, + from_path); + if (ret < 0) + goto out; + ret = fs_path_add_path(from_path, name); + } if (ret < 0) goto out; @@ -3150,7 +3157,8 @@ static int apply_dir_move(struct send_ctx *sctx, struct pending_dir_move *pm) LIST_HEAD(deleted_refs); ASSERT(ancestor > BTRFS_FIRST_FREE_OBJECTID); ret = add_pending_dir_move(sctx, pm->ino, pm->gen, ancestor, - &pm->update_refs, &deleted_refs); + &pm->update_refs, &deleted_refs, + pm->is_orphan); if (ret < 0) goto out; if (rmdir_ino) { @@ -3283,6 +3291,127 @@ out: return ret; } +/* + * We might need to delay a directory rename even when no ancestor directory + * (in the send root) with a higher inode number than ours (sctx->cur_ino) was + * renamed. This happens when we rename a directory to the old name (the name + * in the parent root) of some other unrelated directory that got its rename + * delayed due to some ancestor with higher number that got renamed. + * + * Example: + * + * Parent snapshot: + * . (ino 256) + * |---- a/ (ino 257) + * | |---- file (ino 260) + * | + * |---- b/ (ino 258) + * |---- c/ (ino 259) + * + * Send snapshot: + * . (ino 256) + * |---- a/ (ino 258) + * |---- x/ (ino 259) + * |---- y/ (ino 257) + * |----- file (ino 260) + * + * Here we can not rename 258 from 'b' to 'a' without the rename of inode 257 + * from 'a' to 'x/y' happening first, which in turn depends on the rename of + * inode 259 from 'c' to 'x'. So the order of rename commands the send stream + * must issue is: + * + * 1 - rename 259 from 'c' to 'x' + * 2 - rename 257 from 'a' to 'x/y' + * 3 - rename 258 from 'b' to 'a' + * + * Returns 1 if the rename of sctx->cur_ino needs to be delayed, 0 if it can + * be done right away and < 0 on error. + */ +static int wait_for_dest_dir_move(struct send_ctx *sctx, + struct recorded_ref *parent_ref, + const bool is_orphan) +{ + struct btrfs_path *path; + struct btrfs_key key; + struct btrfs_key di_key; + struct btrfs_dir_item *di; + u64 left_gen; + u64 right_gen; + int ret = 0; + + if (RB_EMPTY_ROOT(&sctx->waiting_dir_moves)) + return 0; + + path = alloc_path_for_send(); + if (!path) + return -ENOMEM; + + key.objectid = parent_ref->dir; + key.type = BTRFS_DIR_ITEM_KEY; + key.offset = btrfs_name_hash(parent_ref->name, parent_ref->name_len); + + ret = btrfs_search_slot(NULL, sctx->parent_root, &key, path, 0, 0); + if (ret < 0) { + goto out; + } else if (ret > 0) { + ret = 0; + goto out; + } + + di = btrfs_match_dir_item_name(sctx->parent_root, path, + parent_ref->name, parent_ref->name_len); + if (!di) { + ret = 0; + goto out; + } + /* + * di_key.objectid has the number of the inode that has a dentry in the + * parent directory with the same name that sctx->cur_ino is being + * renamed to. We need to check if that inode is in the send root as + * well and if it is currently marked as an inode with a pending rename, + * if it is, we need to delay the rename of sctx->cur_ino as well, so + * that it happens after that other inode is renamed. + */ + btrfs_dir_item_key_to_cpu(path->nodes[0], di, &di_key); + if (di_key.type != BTRFS_INODE_ITEM_KEY) { + ret = 0; + goto out; + } + + ret = get_inode_info(sctx->parent_root, di_key.objectid, NULL, + &left_gen, NULL, NULL, NULL, NULL); + if (ret < 0) + goto out; + ret = get_inode_info(sctx->send_root, di_key.objectid, NULL, + &right_gen, NULL, NULL, NULL, NULL); + if (ret < 0) { + if (ret == -ENOENT) + ret = 0; + goto out; + } + + /* Different inode, no need to delay the rename of sctx->cur_ino */ + if (right_gen != left_gen) { + ret = 0; + goto out; + } + + if (is_waiting_for_move(sctx, di_key.objectid)) { + ret = add_pending_dir_move(sctx, + sctx->cur_ino, + sctx->cur_inode_gen, + di_key.objectid, + &sctx->new_refs, + &sctx->deleted_refs, + is_orphan); + if (!ret) + ret = 1; + } +out: + btrfs_free_path(path); + return ret; +} + static int wait_for_parent_move(struct send_ctx *sctx, struct recorded_ref *parent_ref) { @@ -3349,7 +3478,8 @@ out: sctx->cur_inode_gen, ino, &sctx->new_refs, - &sctx->deleted_refs); + &sctx->deleted_refs, + false); if (!ret) ret = 1; } @@ -3372,6 +3502,7 @@ static int process_recorded_refs(struct send_ctx *sctx, int *pending_move) int did_overwrite = 0; int is_orphan = 0; u64 last_dir_ino_rm = 0; + bool can_rename = true; verbose_printk("btrfs: process_recorded_refs %llu\n", sctx->cur_ino); @@ -3490,12 +3621,22 @@ verbose_printk("btrfs: process_recorded_refs %llu\n", sctx->cur_ino); } } + if (S_ISDIR(sctx->cur_inode_mode) && sctx->parent_root) { + ret = wait_for_dest_dir_move(sctx, cur, is_orphan); + if (ret < 0) + goto out; + if (ret == 1) { + can_rename = false; + *pending_move = 1; + } + } + /* * link/move the ref to the new place. If we have an orphan * inode, move it and update valid_path. If not, link or move * it depending on the inode mode. */ - if (is_orphan) { + if (is_orphan && can_rename) { ret = send_rename(sctx, valid_path, cur->full_path); if (ret < 0) goto out; @@ -3503,7 +3644,7 @@ verbose_printk("btrfs: process_recorded_refs %llu\n", sctx->cur_ino); ret = fs_path_copy(valid_path, cur->full_path); if (ret < 0) goto out; - } else { + } else if (can_rename) { if (S_ISDIR(sctx->cur_inode_mode)) { /* * Dirs can't be linked, so move it. For moved -- cgit v1.2.3-59-g8ed1b From b3cffac04eca9af46e1e23560a8ee22b1bd36d43 Mon Sep 17 00:00:00 2001 From: James Hogan Date: Tue, 24 Feb 2015 11:46:20 +0000 Subject: KVM: MIPS: Fix trace event to save PC directly Currently the guest exit trace event saves the VCPU pointer to the structure, and the guest PC is retrieved by dereferencing it when the event is printed rather than directly from the trace record. This isn't safe as the printing may occur long afterwards, after the PC has changed and potentially after the VCPU has been freed. Usually this results in the same (wrong) PC being printed for multiple trace events. It also isn't portable as userland has no way to access the VCPU data structure when interpreting the trace record itself. Lets save the actual PC in the structure so that the correct value is accessible later. Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM") Signed-off-by: James Hogan Cc: Paolo Bonzini Cc: Ralf Baechle Cc: Marcelo Tosatti Cc: Gleb Natapov Cc: Steven Rostedt Cc: Ingo Molnar Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Cc: # v3.10+ Acked-by: Steven Rostedt Signed-off-by: Marcelo Tosatti --- arch/mips/kvm/trace.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/mips/kvm/trace.h b/arch/mips/kvm/trace.h index c1388d40663b..bd6437f67dc0 100644 --- a/arch/mips/kvm/trace.h +++ b/arch/mips/kvm/trace.h @@ -24,18 +24,18 @@ TRACE_EVENT(kvm_exit, TP_PROTO(struct kvm_vcpu *vcpu, unsigned int reason), TP_ARGS(vcpu, reason), TP_STRUCT__entry( - __field(struct kvm_vcpu *, vcpu) + __field(unsigned long, pc) __field(unsigned int, reason) ), TP_fast_assign( - __entry->vcpu = vcpu; + __entry->pc = vcpu->arch.pc; __entry->reason = reason; ), TP_printk("[%s]PC: 0x%08lx", kvm_mips_exit_types_str[__entry->reason], - __entry->vcpu->arch.pc) + __entry->pc) ); #endif /* _TRACE_KVM_H */ -- cgit v1.2.3-59-g8ed1b From cfec0e75f5e9489ec2bf582101b023c845a0a9a5 Mon Sep 17 00:00:00 2001 From: Tapasweni Pathak Date: Sun, 22 Feb 2015 21:48:21 +0530 Subject: KVM: MIPS: Enable after disabling interrupt Enable disabled interrupt, on unsuccessful operation. Found by Coccinelle. Signed-off-by: Tapasweni Pathak Acked-by: Julia Lawall Reviewed-by: James Hogan Signed-off-by: Marcelo Tosatti --- arch/mips/kvm/tlb.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/mips/kvm/tlb.c b/arch/mips/kvm/tlb.c index bbcd82242059..b6beb0e07b1b 100644 --- a/arch/mips/kvm/tlb.c +++ b/arch/mips/kvm/tlb.c @@ -216,6 +216,7 @@ int kvm_mips_host_tlb_write(struct kvm_vcpu *vcpu, unsigned long entryhi, if (idx > current_cpu_data.tlbsize) { kvm_err("%s: Invalid Index: %d\n", __func__, idx); kvm_mips_dump_host_tlbs(); + local_irq_restore(flags); return -1; } -- cgit v1.2.3-59-g8ed1b From 369d6b7f00977eb9090212d4a47ac71f3ec5c217 Mon Sep 17 00:00:00 2001 From: Anna Schumaker Date: Mon, 2 Mar 2015 16:46:09 -0500 Subject: NFS: Fix stateid used for NFS v4 closes After 566fcec60 the client uses the "current stateid" from the nfs4_state structure to close a file. This could potentially contain a delegation stateid, which is disallowed by the protocol and causes servers to return NFS4ERR_BAD_STATEID. This patch restores the (correct) behavior of sending the open stateid to close a file. Reported-by: Olga Kornievskaia Fixes: 566fcec60 (NFSv4: Fix an atomicity problem in CLOSE) Signed-off-by: Anna Schumaker Signed-off-by: Trond Myklebust --- fs/nfs/nfs4proc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index a211daf58c32..732526e04cd5 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -2655,7 +2655,7 @@ static void nfs4_close_done(struct rpc_task *task, void *data) case -NFS4ERR_BAD_STATEID: case -NFS4ERR_EXPIRED: if (!nfs4_stateid_match(&calldata->arg.stateid, - &state->stateid)) { + &state->open_stateid)) { rpc_restart_call_prepare(task); goto out_release; } @@ -2691,7 +2691,7 @@ static void nfs4_close_prepare(struct rpc_task *task, void *data) is_rdwr = test_bit(NFS_O_RDWR_STATE, &state->flags); is_rdonly = test_bit(NFS_O_RDONLY_STATE, &state->flags); is_wronly = test_bit(NFS_O_WRONLY_STATE, &state->flags); - nfs4_stateid_copy(&calldata->arg.stateid, &state->stateid); + nfs4_stateid_copy(&calldata->arg.stateid, &state->open_stateid); /* Calculate the change in open mode */ calldata->arg.fmode = 0; if (state->n_rdwr == 0) { -- cgit v1.2.3-59-g8ed1b From b04b22f4ca691280f0ab3f77954f5a21500881e7 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 13:59:38 -0500 Subject: NFSv4: Ensure that we don't reap a delegation that is being returned Signed-off-by: Trond Myklebust --- fs/nfs/delegation.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/fs/nfs/delegation.c b/fs/nfs/delegation.c index 2e37d8315d92..d9caf73eef48 100644 --- a/fs/nfs/delegation.c +++ b/fs/nfs/delegation.c @@ -815,12 +815,14 @@ restart: inode = nfs_delegation_grab_inode(delegation); if (inode == NULL) continue; - delegation = nfs_detach_delegation(NFS_I(inode), - delegation, server); + delegation = nfs_start_delegation_return_locked(NFS_I(inode)); rcu_read_unlock(); - - if (delegation != NULL) - nfs_free_delegation(delegation); + if (delegation != NULL) { + delegation = nfs_detach_delegation(NFS_I(inode), + delegation, server); + if (delegation != NULL) + nfs_free_delegation(delegation); + } iput(inode); goto restart; } -- cgit v1.2.3-59-g8ed1b From ade04647dd56881e285983af3db702d56ee97e86 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Fri, 27 Feb 2015 14:25:50 -0500 Subject: NFSv4: Ensure we honour NFS_DELEGATION_RETURNING in nfs_inode_set_delegation() Ensure that nfs_inode_set_delegation() doesn't inadvertently detach a delegation that is already in the process of being returned. Signed-off-by: Trond Myklebust --- fs/nfs/delegation.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/fs/nfs/delegation.c b/fs/nfs/delegation.c index d9caf73eef48..5ca502b5f877 100644 --- a/fs/nfs/delegation.c +++ b/fs/nfs/delegation.c @@ -370,7 +370,10 @@ int nfs_inode_set_delegation(struct inode *inode, struct rpc_cred *cred, struct delegation = NULL; goto out; } - freeme = nfs_detach_delegation_locked(nfsi, + if (test_and_set_bit(NFS_DELEGATION_RETURNING, + &old_delegation->flags)) + goto out; + freeme = nfs_detach_delegation_locked(nfsi, old_delegation, clp); if (freeme == NULL) goto out; -- cgit v1.2.3-59-g8ed1b From 9f0f8e12c48e4bb89192a0de876c77dc1fbfaa75 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 09:57:34 -0500 Subject: NFSv4: Pin the superblock while we're returning the delegation This patch ensures that the superblock doesn't go ahead and disappear underneath us while the state manager thread is returning delegations. Signed-off-by: Trond Myklebust --- fs/nfs/delegation.c | 20 ++++++++++++++++---- 1 file changed, 16 insertions(+), 4 deletions(-) diff --git a/fs/nfs/delegation.c b/fs/nfs/delegation.c index 5ca502b5f877..be313e791e67 100644 --- a/fs/nfs/delegation.c +++ b/fs/nfs/delegation.c @@ -474,14 +474,20 @@ restart: super_list) { if (!nfs_delegation_need_return(delegation)) continue; - inode = nfs_delegation_grab_inode(delegation); - if (inode == NULL) + if (!nfs_sb_active(server->super)) continue; + inode = nfs_delegation_grab_inode(delegation); + if (inode == NULL) { + rcu_read_unlock(); + nfs_sb_deactive(server->super); + goto restart; + } delegation = nfs_start_delegation_return_locked(NFS_I(inode)); rcu_read_unlock(); err = nfs_end_delegation_return(inode, delegation, 0); iput(inode); + nfs_sb_deactive(server->super); if (!err) goto restart; set_bit(NFS4CLNT_DELEGRETURN, &clp->cl_state); @@ -815,9 +821,14 @@ restart: if (test_bit(NFS_DELEGATION_NEED_RECLAIM, &delegation->flags) == 0) continue; - inode = nfs_delegation_grab_inode(delegation); - if (inode == NULL) + if (!nfs_sb_active(server->super)) continue; + inode = nfs_delegation_grab_inode(delegation); + if (inode == NULL) { + rcu_read_unlock(); + nfs_sb_deactive(server->super); + goto restart; + } delegation = nfs_start_delegation_return_locked(NFS_I(inode)); rcu_read_unlock(); if (delegation != NULL) { @@ -827,6 +838,7 @@ restart: nfs_free_delegation(delegation); } iput(inode); + nfs_sb_deactive(server->super); goto restart; } } -- cgit v1.2.3-59-g8ed1b From ec3ca4e57e00d52ff724b0ae49f4489667a9c311 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Thu, 26 Feb 2015 14:05:05 -0500 Subject: NFSv4: Ensure we skip delegations that are already being returned In nfs_client_return_marked_delegations() and nfs_delegation_reap_unclaimed() we want to optimise the loop traversal by skipping delegations that are already in the process of being returned. Signed-off-by: Trond Myklebust --- fs/nfs/delegation.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/fs/nfs/delegation.c b/fs/nfs/delegation.c index be313e791e67..a6ad68865880 100644 --- a/fs/nfs/delegation.c +++ b/fs/nfs/delegation.c @@ -436,6 +436,8 @@ static bool nfs_delegation_need_return(struct nfs_delegation *delegation) { bool ret = false; + if (test_bit(NFS_DELEGATION_RETURNING, &delegation->flags)) + goto out; if (test_and_clear_bit(NFS_DELEGATION_RETURN, &delegation->flags)) ret = true; if (test_and_clear_bit(NFS_DELEGATION_RETURN_IF_CLOSED, &delegation->flags) && !ret) { @@ -447,6 +449,7 @@ static bool nfs_delegation_need_return(struct nfs_delegation *delegation) ret = true; spin_unlock(&delegation->lock); } +out: return ret; } @@ -818,6 +821,9 @@ restart: list_for_each_entry_rcu(server, &clp->cl_superblocks, client_link) { list_for_each_entry_rcu(delegation, &server->delegations, super_list) { + if (test_bit(NFS_DELEGATION_RETURNING, + &delegation->flags)) + continue; if (test_bit(NFS_DELEGATION_NEED_RECLAIM, &delegation->flags) == 0) continue; -- cgit v1.2.3-59-g8ed1b From c064a0de1bfb07c34a3798822c7e1636eea866e8 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Sat, 28 Feb 2015 22:24:48 +0100 Subject: livepatch: fix RCU usage in klp_find_external_symbol() While one must hold RCU-sched (aka. preempt_disable) for find_symbol() one must equally hold it over the use of the object returned. The moment you release the RCU-sched read lock, the object can be dead and gone. [jkosina@suse.cz: change subject line to be aligned with other patches] Cc: Seth Jennings Cc: Josh Poimboeuf Cc: Masami Hiramatsu Cc: Miroslav Benes Cc: Petr Mladek Cc: Jiri Kosina Cc: "Paul E. McKenney" Cc: Rusty Russell Signed-off-by: Peter Zijlstra (Intel) Reviewed-by: Masami Hiramatsu Acked-by: Paul E. McKenney Acked-by: Josh Poimboeuf Signed-off-by: Jiri Kosina --- kernel/livepatch/core.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/livepatch/core.c b/kernel/livepatch/core.c index 782172f073c5..01ca08804f51 100644 --- a/kernel/livepatch/core.c +++ b/kernel/livepatch/core.c @@ -248,11 +248,12 @@ static int klp_find_external_symbol(struct module *pmod, const char *name, /* first, check if it's an exported symbol */ preempt_disable(); sym = find_symbol(name, NULL, NULL, true, true); - preempt_enable(); if (sym) { *addr = sym->value; + preempt_enable(); return 0; } + preempt_enable(); /* otherwise check if it's in another .o within the patch module */ return klp_find_object_symbol(pmod->name, name, addr); -- cgit v1.2.3-59-g8ed1b From 7d7355f58ba4f9d68d2fb79864bab4ccb618e4e1 Mon Sep 17 00:00:00 2001 From: Ben Hutchings Date: Tue, 3 Mar 2015 00:52:00 +0000 Subject: sh_eth: Ensure proper ordering of descriptor active bit write/read When submitting a DMA descriptor, the active bit must be written last. When reading a completed DMA descriptor, the active bit must be read first. Add memory barriers to ensure that this ordering is maintained. Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 654b48d1e61a..5c212a833bcf 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1410,6 +1410,8 @@ static int sh_eth_txfree(struct net_device *ndev) txdesc = &mdp->tx_ring[entry]; if (txdesc->status & cpu_to_edmac(mdp, TD_TACT)) break; + /* TACT bit must be checked before all the following reads */ + rmb(); /* Free the original skb. */ if (mdp->tx_skbuff[entry]) { dma_unmap_single(&ndev->dev, txdesc->addr, @@ -1447,6 +1449,8 @@ static int sh_eth_rx(struct net_device *ndev, u32 intr_status, int *quota) limit = boguscnt; rxdesc = &mdp->rx_ring[entry]; while (!(rxdesc->status & cpu_to_edmac(mdp, RD_RACT))) { + /* RACT bit must be checked before all the following reads */ + rmb(); desc_status = edmac_to_cpu(mdp, rxdesc->status); pkt_len = rxdesc->frame_length; @@ -1526,6 +1530,7 @@ static int sh_eth_rx(struct net_device *ndev, u32 intr_status, int *quota) skb_checksum_none_assert(skb); rxdesc->addr = dma_addr; } + wmb(); /* RACT bit must be set after all the above writes */ if (entry >= mdp->num_rx_ring - 1) rxdesc->status |= cpu_to_edmac(mdp, RD_RACT | RD_RFP | RD_RDEL); @@ -2195,6 +2200,7 @@ static int sh_eth_start_xmit(struct sk_buff *skb, struct net_device *ndev) } txdesc->buffer_length = skb->len; + wmb(); /* TACT bit must be set after all the above writes */ if (entry >= mdp->num_tx_ring - 1) txdesc->status |= cpu_to_edmac(mdp, TD_TACT | TD_TDLE); else -- cgit v1.2.3-59-g8ed1b From 6ded286555c2518be2f2d438f83dfaba3f0100fd Mon Sep 17 00:00:00 2001 From: Ben Hutchings Date: Tue, 3 Mar 2015 00:52:08 +0000 Subject: sh_eth: Fix RX recovery on R-Car in case of RX ring underrun In case of RX ring underrun (RDE), we attempt to reset the software descriptor pointers (dirty_rx and cur_rx) to match where the hardware will read the next descriptor from, as that might not be the first dirty descriptor. This relies on reading RDFAR, but that register doesn't exist on all supported chips - specifically, not on the R-Car chips. This will result in unpredictable behaviour on those chips after an RDE. Make this pointer reset conditional and assume that it isn't needed on the R-Car chips. This fix also assumes that RDFAR is never exposed at offset 0 in the memory map - this is currently true, and a subsequent commit will fix the ambiguity between offset 0 and no-offset in the register offset maps. Fixes: 79fba9f51755 ("net: sh_eth: fix the rxdesc pointer when rx ...") Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 5c212a833bcf..3309494d12ad 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1543,7 +1543,7 @@ static int sh_eth_rx(struct net_device *ndev, u32 intr_status, int *quota) /* If we don't need to check status, don't. -KDU */ if (!(sh_eth_read(ndev, EDRRR) & EDRRR_R)) { /* fix the values for the next receiving if RDE is set */ - if (intr_status & EESR_RDE) { + if (intr_status & EESR_RDE && mdp->reg_offset[RDFAR] != 0) { u32 count = (sh_eth_read(ndev, RDFAR) - sh_eth_read(ndev, RDLAR)) >> 4; -- cgit v1.2.3-59-g8ed1b From 9b4a6364a6b3176511956ad186f8dffbe2e60c3e Mon Sep 17 00:00:00 2001 From: Ben Hutchings Date: Tue, 3 Mar 2015 00:52:39 +0000 Subject: Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790" This reverts commit fd9af07c3404ac9ecbd0d859563360f51ce1ffde. The hardware manual states that the frame error and multicast bits are copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too long) and RFS8 (multicast). Also adjust a comment to agree with this. Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 3309494d12ad..3406cda57a45 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -508,7 +508,6 @@ static struct sh_eth_cpu_data r8a779x_data = { .tpauser = 1, .hw_swap = 1, .rmiimode = 1, - .shift_rd0 = 1, }; static void sh_eth_set_rate_sh7724(struct net_device *ndev) @@ -1462,8 +1461,8 @@ static int sh_eth_rx(struct net_device *ndev, u32 intr_status, int *quota) /* In case of almost all GETHER/ETHERs, the Receive Frame State * (RFS) bits in the Receive Descriptor 0 are from bit 9 to - * bit 0. However, in case of the R8A7740, R8A779x, and - * R7S72100 the RFS bits are from bit 25 to bit 16. So, the + * bit 0. However, in case of the R8A7740 and R7S72100 + * the RFS bits are from bit 25 to bit 16. So, the * driver needs right shifting by 16. */ if (mdp->cd->shift_rd0) -- cgit v1.2.3-59-g8ed1b From dacc73e0cf930e87e2e6a94d29156f1d5776b18f Mon Sep 17 00:00:00 2001 From: Ben Hutchings Date: Tue, 3 Mar 2015 00:53:08 +0000 Subject: sh_eth: Really fix padding of short frames on TX MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit My previous fix to clear padding of short frames used skb->len as the DMA length, assuming that skb_padto() extended skb->len to include the padding. That isn't the case; we need to use skb_put_padto() instead. (This wasn't immediately obvious because software padding isn't actually needed on the R-Car H2. We could make it conditional on which chip is being driven, but it's probably not worth the effort.) Reported-by: "Violeta Menéndez González" Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX") Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 3406cda57a45..736d5d1624a1 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -2181,7 +2181,7 @@ static int sh_eth_start_xmit(struct sk_buff *skb, struct net_device *ndev) } spin_unlock_irqrestore(&mdp->lock, flags); - if (skb_padto(skb, ETH_ZLEN)) + if (skb_put_padto(skb, ETH_ZLEN)) return NETDEV_TX_OK; entry = mdp->cur_tx % mdp->num_tx_ring; -- cgit v1.2.3-59-g8ed1b From acf8dd0a9d0b9e4cdb597c2f74802f79c699e802 Mon Sep 17 00:00:00 2001 From: Michal Kubeček Date: Mon, 2 Mar 2015 18:27:11 +0100 Subject: udp: only allow UFO for packets from SOCK_DGRAM sockets If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer checksum is to be computed on segmentation. However, in this case, skb->csum_start and skb->csum_offset are never set as raw socket transmit path bypasses udp_send_skb() where they are usually set. As a result, driver may access invalid memory when trying to calculate the checksum and store the result (as observed in virtio_net driver). Moreover, the very idea of modifying the userspace provided UDP header is IMHO against raw socket semantics (I wasn't able to find a document clearly stating this or the opposite, though). And while allowing CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit too intrusive change just to handle a corner case like this. Therefore disallowing UFO for packets from SOCK_DGRAM seems to be the best option. Signed-off-by: Michal Kubecek Signed-off-by: David S. Miller --- net/ipv4/ip_output.c | 3 ++- net/ipv6/ip6_output.c | 3 ++- 2 files changed, 4 insertions(+), 2 deletions(-) diff --git a/net/ipv4/ip_output.c b/net/ipv4/ip_output.c index d68199d9b2b0..a7aea2048a0d 100644 --- a/net/ipv4/ip_output.c +++ b/net/ipv4/ip_output.c @@ -888,7 +888,8 @@ static int __ip_append_data(struct sock *sk, cork->length += length; if (((length > mtu) || (skb && skb_is_gso(skb))) && (sk->sk_protocol == IPPROTO_UDP) && - (rt->dst.dev->features & NETIF_F_UFO) && !rt->dst.header_len) { + (rt->dst.dev->features & NETIF_F_UFO) && !rt->dst.header_len && + (sk->sk_type == SOCK_DGRAM)) { err = ip_ufo_append_data(sk, queue, getfrag, from, length, hh_len, fragheaderlen, transhdrlen, maxfraglen, flags); diff --git a/net/ipv6/ip6_output.c b/net/ipv6/ip6_output.c index 7deebf102cba..0a04a37305d5 100644 --- a/net/ipv6/ip6_output.c +++ b/net/ipv6/ip6_output.c @@ -1298,7 +1298,8 @@ emsgsize: if (((length > mtu) || (skb && skb_is_gso(skb))) && (sk->sk_protocol == IPPROTO_UDP) && - (rt->dst.dev->features & NETIF_F_UFO)) { + (rt->dst.dev->features & NETIF_F_UFO) && + (sk->sk_type == SOCK_DGRAM)) { err = ip6_ufo_append_data(sk, queue, getfrag, from, length, hh_len, fragheaderlen, transhdrlen, mtu, flags, rt); -- cgit v1.2.3-59-g8ed1b From c7d373c3f0da2b2b78c4b1ce5ae41485b3ef848c Mon Sep 17 00:00:00 2001 From: Max Mansfield Date: Mon, 2 Mar 2015 18:38:02 -0700 Subject: usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards This patch integrates Cyber Cortex AV boards with the existing ftdi_jtag_quirk in order to use serial port 0 with JTAG which is required by the manufacturers' software. Steps: 2 [ftdi_sio_ids.h] 1. Defined the device PID [ftdi_sio.c] 2. Added a macro declaration to the ids array, in order to enable the jtag quirk for the device. Signed-off-by: Max Mansfield Cc: stable Signed-off-by: Johan Hovold --- drivers/usb/serial/ftdi_sio.c | 2 ++ drivers/usb/serial/ftdi_sio_ids.h | 3 +++ 2 files changed, 5 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 651dc1ba46c3..3086dec0ef53 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -799,6 +799,8 @@ static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(FTDI_VID, FTDI_ELSTER_UNICOM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PROPOX_JTAGCABLEII_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PROPOX_ISPCABLEIII_PID) }, + { USB_DEVICE(FTDI_VID, CYBER_CORTEX_AV_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(OLIMEX_VID, OLIMEX_ARM_USB_OCD_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(OLIMEX_VID, OLIMEX_ARM_USB_OCD_H_PID), diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index 4d3da89cd8dd..56b1b55c4751 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -38,6 +38,9 @@ #define FTDI_LUMEL_PD12_PID 0x6002 +/* Cyber Cortex AV by Fabulous Silicon (http://fabuloussilicon.com) */ +#define CYBER_CORTEX_AV_PID 0x8698 + /* * Marvell OpenRD Base, Client * http://www.open-rd.org -- cgit v1.2.3-59-g8ed1b From 6d65261a09adaa374c05de807f73a144d783669e Mon Sep 17 00:00:00 2001 From: Tyler Hicks Date: Tue, 24 Feb 2015 19:28:10 -0600 Subject: eCryptfs: don't pass fs-specific ioctl commands through eCryptfs can't be aware of what to expect when after passing an arbitrary ioctl command through to the lower filesystem. The ioctl command may trigger an action in the lower filesystem that is incompatible with eCryptfs. One specific example is when one attempts to use the Btrfs clone ioctl command when the source file is in the Btrfs filesystem that eCryptfs is mounted on top of and the destination fd is from a new file created in the eCryptfs mount. The ioctl syscall incorrectly returns success because the command is passed down to Btrfs which thinks that it was able to do the clone operation. However, the result is an empty eCryptfs file. This patch allows the trim, {g,s}etflags, and {g,s}etversion ioctl commands through and then copies up the inode metadata from the lower inode to the eCryptfs inode to catch any changes made to the lower inode's metadata. Those five ioctl commands are mostly common across all filesystems but the whitelist may need to be further pruned in the future. https://bugzilla.kernel.org/show_bug.cgi?id=93691 https://launchpad.net/bugs/1305335 Signed-off-by: Tyler Hicks Cc: Rocko Cc: Colin Ian King Cc: stable@vger.kernel.org # v2.6.36+: c43f7b8 eCryptfs: Handle ioctl calls with unlocked and compat functions --- fs/ecryptfs/file.c | 34 ++++++++++++++++++++++++++++++---- 1 file changed, 30 insertions(+), 4 deletions(-) diff --git a/fs/ecryptfs/file.c b/fs/ecryptfs/file.c index b07731e68c0b..fd39bad6f1bd 100644 --- a/fs/ecryptfs/file.c +++ b/fs/ecryptfs/file.c @@ -303,9 +303,22 @@ ecryptfs_unlocked_ioctl(struct file *file, unsigned int cmd, unsigned long arg) struct file *lower_file = ecryptfs_file_to_lower(file); long rc = -ENOTTY; - if (lower_file->f_op->unlocked_ioctl) + if (!lower_file->f_op->unlocked_ioctl) + return rc; + + switch (cmd) { + case FITRIM: + case FS_IOC_GETFLAGS: + case FS_IOC_SETFLAGS: + case FS_IOC_GETVERSION: + case FS_IOC_SETVERSION: rc = lower_file->f_op->unlocked_ioctl(lower_file, cmd, arg); - return rc; + fsstack_copy_attr_all(file_inode(file), file_inode(lower_file)); + + return rc; + default: + return rc; + } } #ifdef CONFIG_COMPAT @@ -315,9 +328,22 @@ ecryptfs_compat_ioctl(struct file *file, unsigned int cmd, unsigned long arg) struct file *lower_file = ecryptfs_file_to_lower(file); long rc = -ENOIOCTLCMD; - if (lower_file->f_op->compat_ioctl) + if (!lower_file->f_op->compat_ioctl) + return rc; + + switch (cmd) { + case FITRIM: + case FS_IOC32_GETFLAGS: + case FS_IOC32_SETFLAGS: + case FS_IOC32_GETVERSION: + case FS_IOC32_SETVERSION: rc = lower_file->f_op->compat_ioctl(lower_file, cmd, arg); - return rc; + fsstack_copy_attr_all(file_inode(file), file_inode(lower_file)); + + return rc; + default: + return rc; + } } #endif -- cgit v1.2.3-59-g8ed1b From 9c58e8dbd3bfe7197323c88a784617afeffa9f87 Mon Sep 17 00:00:00 2001 From: Daniel Vetter Date: Tue, 3 Mar 2015 10:58:08 +0100 Subject: drm/rockchip: Flip select/depends in Kconfig Otherwise Kconfig gets confused and somehow ends up creating a 2nd drm submenu. I couldn't find i915 because of this any more at first. Cc: Andy Yan Cc: Russell King Cc: Philipp Zabel Cc: "Yann E. MORIN" Cc: linux-kbuild@vger.kernel.or Signed-off-by: Daniel Vetter Signed-off-by: Dave Airlie --- drivers/gpu/drm/rockchip/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig index 35215f6867d3..c22310c91672 100644 --- a/drivers/gpu/drm/rockchip/Kconfig +++ b/drivers/gpu/drm/rockchip/Kconfig @@ -18,8 +18,8 @@ config DRM_ROCKCHIP config ROCKCHIP_DW_HDMI tristate "Rockchip specific extensions for Synopsys DW HDMI" - depends on DRM_ROCKCHIP select DRM_DW_HDMI + depends on DRM_ROCKCHIP help This selects support for Rockchip SoC specific extensions for the Synopsys DesignWare HDMI driver. If you want to -- cgit v1.2.3-59-g8ed1b From ed9ed50ccc2c16690b921171c809f6f15255ac65 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 3 Mar 2015 20:58:43 +1000 Subject: Revert "drm/rockchip: Flip select/depends in Kconfig" This reverts commit 9c58e8dbd3bfe7197323c88a784617afeffa9f87. This doesn't seem to fully fix this, Kbuild who knows. Signed-off-by: Dave Airlie --- drivers/gpu/drm/rockchip/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig index c22310c91672..35215f6867d3 100644 --- a/drivers/gpu/drm/rockchip/Kconfig +++ b/drivers/gpu/drm/rockchip/Kconfig @@ -18,8 +18,8 @@ config DRM_ROCKCHIP config ROCKCHIP_DW_HDMI tristate "Rockchip specific extensions for Synopsys DW HDMI" - select DRM_DW_HDMI depends on DRM_ROCKCHIP + select DRM_DW_HDMI help This selects support for Rockchip SoC specific extensions for the Synopsys DesignWare HDMI driver. If you want to -- cgit v1.2.3-59-g8ed1b From 31f3032c1a5504259f6fa8e0c7f8d2d3e2f5db48 Mon Sep 17 00:00:00 2001 From: Vishal Thanki Date: Tue, 3 Mar 2015 18:59:00 +0530 Subject: ASoC: simple-card: Add a NULL pointer check in asoc_simple_card_dai_link_of Make sure devm_kzalloc() succeeds. Signed-off-by: Vishal Thanki Signed-off-by: Mark Brown --- sound/soc/generic/simple-card.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/sound/soc/generic/simple-card.c b/sound/soc/generic/simple-card.c index f7c6734bd5da..fb550b5869d2 100644 --- a/sound/soc/generic/simple-card.c +++ b/sound/soc/generic/simple-card.c @@ -372,6 +372,11 @@ static int asoc_simple_card_dai_link_of(struct device_node *node, strlen(dai_link->cpu_dai_name) + strlen(dai_link->codec_dai_name) + 2, GFP_KERNEL); + if (!name) { + ret = -ENOMEM; + goto dai_link_of_err; + } + sprintf(name, "%s-%s", dai_link->cpu_dai_name, dai_link->codec_dai_name); dai_link->name = dai_link->stream_name = name; -- cgit v1.2.3-59-g8ed1b From 9128b040eb774e04bc23777b005ace2b66ab2a85 Mon Sep 17 00:00:00 2001 From: Daniel Vetter Date: Tue, 3 Mar 2015 17:31:21 +0100 Subject: drm/i915: Fix modeset state confusion in the load detect code This is a tricky story of the new atomic state handling and the legacy code fighting over each another. The bug at hand is an underrun of the framebuffer reference with subsequent hilarity caused by the load detect code. Which is peculiar since the the exact same code works fine as the implementation of the legacy setcrtc ioctl. Let's look at the ingredients: - Currently our code is a crazy mix of legacy modeset interfaces to set the parameters and half-baked atomic state tracking underneath. While this transition is going we're using the transitional plane helpers to update the atomic side (drm_plane_helper_disable/update and friends), i.e. plane->state->fb. Since the state structure owns the fb those functions take care of that themselves. The legacy state (specifically crtc->primary->fb) is still managed by the old code (and mostly by the drm core), with the fb reference counting done by callers (core drm for the ioctl or the i915 load detect code). The relevant commit is commit ea2c67bb4affa84080c616920f3899f123786e56 Author: Matt Roper Date: Tue Dec 23 10:41:52 2014 -0800 drm/i915: Move to atomic plane helpers (v9) - drm_plane_helper_disable has special code to handle multiple calls in a row - it checks plane->crtc == NULL and bails out. This is to match the proper atomic implementation which needs the crtc to get at the implied locking context atomic updates always need. See commit acf24a395c5a9290189b080383564437101d411c Author: Daniel Vetter Date: Tue Jul 29 15:33:05 2014 +0200 drm/plane-helper: transitional atomic plane helpers - The universal plane code split out the implicit primary plane from the CRTC into it's own full-blown drm_plane object. As part of that the setcrtc ioctl (which updated both the crtc mode and primary plane) learned to set crtc->primary->crtc on modeset to make sure the plane->crtc assignments statate up to date in commit e13161af80c185ecd8dc4641d0f5df58f9e3e0af Author: Matt Roper Date: Tue Apr 1 15:22:38 2014 -0700 drm: Add drm_crtc_init_with_planes() (v2) Unfortunately we've forgotten to update the load detect code. Which wasn't a problem since the load detect modeset is temporary and always undone before we drop the locks. - Finally there is a organically grown history (i.e. don't ask) around who sets the legacy plane->fb for the various driver entry points. Originally updating that was the drivers duty, but for almost all places we've moved that (plus updating the refcounts) into the core. Again the exception is the load detect code. Taking all together the following happens: - The load detect code doesn't set crtc->primary->crtc. This is only really an issue on crtcs never before used or when userspace explicitly disabled the primary plane. - The plane helper glue code short-circuits because of that and leaves a non-NULL fb behind in plane->state->fb and plane->fb. The state fb isn't a real problem (it's properly refcounted on its own), it's just the canary. - Load detect code drops the reference for that fb, but doesn't set plane->fb = NULL. This is ok since it's still living in that old world where drivers had to clear the pointer but the core/callers handled the refcounting. - On the next modeset the drm core notices plane->fb and takes care of refcounting it properly by doing another unref. This drops the refcount to zero, leaving state->plane now pointing at freed memory. - intel_plane_duplicate_state still assume it owns a reference to that very state->fb and bad things start to happen. Fix this all by applying the same duct-tape as for the legacy setcrtc ioctl code and set crtc->primary->crtc properly. Cc: Matt Roper Cc: Paul Bolle Cc: Rob Clark Cc: Paulo Zanoni Cc: Sean Paul Cc: Matt Roper Reported-and-tested-by: Linus Torvalds Reported-by: Paul Bolle Signed-off-by: Daniel Vetter Signed-off-by: Linus Torvalds --- drivers/gpu/drm/i915/intel_display.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 3117679299a6..e730789b53b7 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -8713,6 +8713,7 @@ retry: old->release_fb->funcs->destroy(old->release_fb); goto fail; } + crtc->primary->crtc = crtc; /* let the connector get through one full cycle before testing */ intel_wait_for_vblank(dev, intel_crtc->pipe); -- cgit v1.2.3-59-g8ed1b From 13a7a6ac0a11197edcd0f756a035f472b42cdf8b Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 3 Mar 2015 09:04:59 -0800 Subject: Linux 4.0-rc2 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 9fab639727c7..e6a9b1b94656 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 4 PATCHLEVEL = 0 SUBLEVEL = 0 -EXTRAVERSION = -rc1 +EXTRAVERSION = -rc2 NAME = Hurr durr I'ma sheep # *DOCUMENTATION* -- cgit v1.2.3-59-g8ed1b From 874f946376de57c8d6230b30ad71f742883fee3a Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Mon, 2 Mar 2015 23:32:08 -0500 Subject: NFS: Fix a regression in the read() syscall When invalidating the page cache for a regular file, we want to first sync all dirty data to disk and then call invalidate_inode_pages2(). The latter relies on nfs_launder_page() and nfs_release_page() to deal respectively with dirty pages, and unstable written pages. When commit 9590544694bec ("NFS: avoid deadlocks with loop-back mounted NFS filesystems.") changed the behaviour of nfs_release_page(), then it made it possible for invalidate_inode_pages2() to fail with an EBUSY. Unfortunately, that error is then propagated back to read(). Let's therefore work around the problem for now by protecting the call to sync the data and invalidate_inode_pages2() so that they are atomic w.r.t. the addition of new writes. Later on, we can revisit whether or not we still need nfs_launder_page() and nfs_release_page(). Signed-off-by: Trond Myklebust --- fs/nfs/file.c | 4 ++-- fs/nfs/inode.c | 37 ++++++++++++++++++++++++++++++++++--- include/linux/nfs_fs.h | 1 + 3 files changed, 37 insertions(+), 5 deletions(-) diff --git a/fs/nfs/file.c b/fs/nfs/file.c index c045c7169fa0..41963ffca597 100644 --- a/fs/nfs/file.c +++ b/fs/nfs/file.c @@ -178,7 +178,7 @@ nfs_file_read(struct kiocb *iocb, struct iov_iter *to) iocb->ki_filp, iov_iter_count(to), (unsigned long) iocb->ki_pos); - result = nfs_revalidate_mapping(inode, iocb->ki_filp->f_mapping); + result = nfs_revalidate_mapping_protected(inode, iocb->ki_filp->f_mapping); if (!result) { result = generic_file_read_iter(iocb, to); if (result > 0) @@ -199,7 +199,7 @@ nfs_file_splice_read(struct file *filp, loff_t *ppos, dprintk("NFS: splice_read(%pD2, %lu@%Lu)\n", filp, (unsigned long) count, (unsigned long long) *ppos); - res = nfs_revalidate_mapping(inode, filp->f_mapping); + res = nfs_revalidate_mapping_protected(inode, filp->f_mapping); if (!res) { res = generic_file_splice_read(filp, ppos, pipe, count, flags); if (res > 0) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index 5026c44a98e1..8edb7d049565 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1067,11 +1067,14 @@ static bool nfs_mapping_need_revalidate_inode(struct inode *inode) } /** - * nfs_revalidate_mapping - Revalidate the pagecache + * __nfs_revalidate_mapping - Revalidate the pagecache * @inode - pointer to host inode * @mapping - pointer to mapping + * @may_lock - take inode->i_mutex? */ -int nfs_revalidate_mapping(struct inode *inode, struct address_space *mapping) +static int __nfs_revalidate_mapping(struct inode *inode, + struct address_space *mapping, + bool may_lock) { struct nfs_inode *nfsi = NFS_I(inode); unsigned long *bitlock = &nfsi->flags; @@ -1120,7 +1123,12 @@ int nfs_revalidate_mapping(struct inode *inode, struct address_space *mapping) nfsi->cache_validity &= ~NFS_INO_INVALID_DATA; spin_unlock(&inode->i_lock); trace_nfs_invalidate_mapping_enter(inode); - ret = nfs_invalidate_mapping(inode, mapping); + if (may_lock) { + mutex_lock(&inode->i_mutex); + ret = nfs_invalidate_mapping(inode, mapping); + mutex_unlock(&inode->i_mutex); + } else + ret = nfs_invalidate_mapping(inode, mapping); trace_nfs_invalidate_mapping_exit(inode, ret); clear_bit_unlock(NFS_INO_INVALIDATING, bitlock); @@ -1130,6 +1138,29 @@ out: return ret; } +/** + * nfs_revalidate_mapping - Revalidate the pagecache + * @inode - pointer to host inode + * @mapping - pointer to mapping + */ +int nfs_revalidate_mapping(struct inode *inode, struct address_space *mapping) +{ + return __nfs_revalidate_mapping(inode, mapping, false); +} + +/** + * nfs_revalidate_mapping_protected - Revalidate the pagecache + * @inode - pointer to host inode + * @mapping - pointer to mapping + * + * Differs from nfs_revalidate_mapping() in that it grabs the inode->i_mutex + * while invalidating the mapping. + */ +int nfs_revalidate_mapping_protected(struct inode *inode, struct address_space *mapping) +{ + return __nfs_revalidate_mapping(inode, mapping, true); +} + static unsigned long nfs_wcc_update_inode(struct inode *inode, struct nfs_fattr *fattr) { struct nfs_inode *nfsi = NFS_I(inode); diff --git a/include/linux/nfs_fs.h b/include/linux/nfs_fs.h index 59b1516b9fd4..b01ccf371fdc 100644 --- a/include/linux/nfs_fs.h +++ b/include/linux/nfs_fs.h @@ -356,6 +356,7 @@ extern int nfs_revalidate_inode(struct nfs_server *server, struct inode *inode); extern int nfs_revalidate_inode_rcu(struct nfs_server *server, struct inode *inode); extern int __nfs_revalidate_inode(struct nfs_server *, struct inode *); extern int nfs_revalidate_mapping(struct inode *inode, struct address_space *mapping); +extern int nfs_revalidate_mapping_protected(struct inode *inode, struct address_space *mapping); extern int nfs_setattr(struct dentry *, struct iattr *); extern void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr, struct nfs_fattr *); extern void nfs_setsecurity(struct inode *inode, struct nfs_fattr *fattr, -- cgit v1.2.3-59-g8ed1b From ef070dcb3989f553f5d84edf555eebc7e204099d Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Tue, 3 Mar 2015 00:06:35 -0500 Subject: NFS: Don't write enable new pages while an invalidation is proceeding nfs_vm_page_mkwrite() should wait until the page cache invalidation is finished. This is the second patch in a 2 patch series to deprecate the NFS client's reliance on nfs_release_page() in the context of nfs_invalidate_mapping(). Signed-off-by: Trond Myklebust --- fs/nfs/file.c | 3 +++ fs/nfs/inode.c | 1 + 2 files changed, 4 insertions(+) diff --git a/fs/nfs/file.c b/fs/nfs/file.c index 41963ffca597..e679d24c39d3 100644 --- a/fs/nfs/file.c +++ b/fs/nfs/file.c @@ -623,6 +623,9 @@ static int nfs_vm_page_mkwrite(struct vm_area_struct *vma, struct vm_fault *vmf) /* make sure the cache has finished storing the page */ nfs_fscache_wait_on_page_write(NFS_I(inode), page); + wait_on_bit_action(&NFS_I(inode)->flags, NFS_INO_INVALIDATING, + nfs_wait_bit_killable, TASK_KILLABLE); + lock_page(page); mapping = page_file_mapping(page); if (mapping != inode->i_mapping) diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c index 8edb7d049565..d42dff6d5e98 100644 --- a/fs/nfs/inode.c +++ b/fs/nfs/inode.c @@ -1035,6 +1035,7 @@ static int nfs_invalidate_mapping(struct inode *inode, struct address_space *map if (mapping->nrpages != 0) { if (S_ISREG(inode->i_mode)) { + unmap_mapping_range(mapping, 0, 0, 0); ret = nfs_sync_mapping(mapping); if (ret < 0) return ret; -- cgit v1.2.3-59-g8ed1b From 71e168b151babf4334e2e26c92230a6bda3b1f24 Mon Sep 17 00:00:00 2001 From: Florian Westphal Date: Tue, 3 Mar 2015 13:53:31 +0100 Subject: net: bridge: add compile-time assert for cb struct size make build fail if structure no longer fits into ->cb storage. Signed-off-by: Florian Westphal Signed-off-by: David S. Miller --- net/bridge/br.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/bridge/br.c b/net/bridge/br.c index fb57ab6b24f9..02c24cf63c34 100644 --- a/net/bridge/br.c +++ b/net/bridge/br.c @@ -190,6 +190,8 @@ static int __init br_init(void) { int err; + BUILD_BUG_ON(sizeof(struct br_input_skb_cb) > FIELD_SIZEOF(struct sk_buff, cb)); + err = stp_proto_register(&br_stp_proto); if (err < 0) { pr_err("bridge: can't register sap for STP\n"); -- cgit v1.2.3-59-g8ed1b From c77c761fa40e0ebdacb728b0310191ef8dc6902b Mon Sep 17 00:00:00 2001 From: Thomas Falcon Date: Mon, 2 Mar 2015 11:56:12 -0600 Subject: ibmveth: Add function to enable live MAC address changes Add a function that will enable changing the MAC address of an ibmveth interface while it is still running. Signed-off-by: Thomas Falcon Reviewed-by: Jiri Pirko Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/ibmveth.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/ibm/ibmveth.c b/drivers/net/ethernet/ibm/ibmveth.c index 21978cc019e7..072426a72745 100644 --- a/drivers/net/ethernet/ibm/ibmveth.c +++ b/drivers/net/ethernet/ibm/ibmveth.c @@ -1327,6 +1327,28 @@ static unsigned long ibmveth_get_desired_dma(struct vio_dev *vdev) return ret; } +static int ibmveth_set_mac_addr(struct net_device *dev, void *p) +{ + struct ibmveth_adapter *adapter = netdev_priv(dev); + struct sockaddr *addr = p; + u64 mac_address; + int rc; + + if (!is_valid_ether_addr(addr->sa_data)) + return -EADDRNOTAVAIL; + + mac_address = ibmveth_encode_mac_addr(addr->sa_data); + rc = h_change_logical_lan_mac(adapter->vdev->unit_address, mac_address); + if (rc) { + netdev_err(adapter->netdev, "h_change_logical_lan_mac failed with rc=%d\n", rc); + return rc; + } + + ether_addr_copy(dev->dev_addr, addr->sa_data); + + return 0; +} + static const struct net_device_ops ibmveth_netdev_ops = { .ndo_open = ibmveth_open, .ndo_stop = ibmveth_close, @@ -1337,7 +1359,7 @@ static const struct net_device_ops ibmveth_netdev_ops = { .ndo_fix_features = ibmveth_fix_features, .ndo_set_features = ibmveth_set_features, .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, + .ndo_set_mac_address = ibmveth_set_mac_addr, #ifdef CONFIG_NET_POLL_CONTROLLER .ndo_poll_controller = ibmveth_poll_controller, #endif -- cgit v1.2.3-59-g8ed1b From 0ae93b2cccbcc060899800a6bac7905a7d754448 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Mon, 2 Mar 2015 12:03:27 -0800 Subject: gianfar: Reduce logging noise seen due to phy polling if link is down Commit 6ce29b0e2a04 ("gianfar: Avoid unnecessary reg accesses in adjust_link()") eliminates unnecessary calls to adjust_link for phy devices which don't support interrupts and need polling. As part of that work, the 'new_state' local flag, which was used to reduce logging noise on the console, was eliminated. Unfortunately, that means that a 'Link is Down' log message will now be issued continuously if a link is configured as UP, the link state is down, and the associated phy requires polling. This occurs because priv->oldduplex is -1 in this case, which always differs from phydev->duplex. In addition, phydev->speed may also differ from priv->oldspeed. gfar_update_link_state() is therefore called each time a phy is polled, even if the link state did not change. Cc: Claudiu Manoil Signed-off-by: Guenter Roeck Reviewed-by: Claudiu Manoil Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/gianfar.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/freescale/gianfar.c b/drivers/net/ethernet/freescale/gianfar.c index 43df78882e48..178e54028d10 100644 --- a/drivers/net/ethernet/freescale/gianfar.c +++ b/drivers/net/ethernet/freescale/gianfar.c @@ -3162,8 +3162,8 @@ static void adjust_link(struct net_device *dev) struct phy_device *phydev = priv->phydev; if (unlikely(phydev->link != priv->oldlink || - phydev->duplex != priv->oldduplex || - phydev->speed != priv->oldspeed)) + (phydev->link && (phydev->duplex != priv->oldduplex || + phydev->speed != priv->oldspeed)))) gfar_update_link_state(priv); } -- cgit v1.2.3-59-g8ed1b From f4f8e73850589008095b1da3c8c17cf68bd1c62a Mon Sep 17 00:00:00 2001 From: Joe Stringer Date: Mon, 2 Mar 2015 18:49:56 -0800 Subject: openvswitch: Fix serialization of non-masked set actions. Set actions consist of a regular OVS_KEY_ATTR_* attribute nested inside of a OVS_ACTION_ATTR_SET action attribute. When converting masked actions back to regular set actions, the inner attribute length was not changed, ie, double the length being serialized. This patch fixes the bug. Fixes: 83d2b9b ("net: openvswitch: Support masked set actions.") Signed-off-by: Joe Stringer Acked-by: Jarno Rajahalme Signed-off-by: David S. Miller --- net/openvswitch/flow_netlink.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/net/openvswitch/flow_netlink.c b/net/openvswitch/flow_netlink.c index 216f20b90aa5..22b18c145c92 100644 --- a/net/openvswitch/flow_netlink.c +++ b/net/openvswitch/flow_netlink.c @@ -2253,14 +2253,20 @@ static int masked_set_action_to_set_action_attr(const struct nlattr *a, struct sk_buff *skb) { const struct nlattr *ovs_key = nla_data(a); + struct nlattr *nla; size_t key_len = nla_len(ovs_key) / 2; /* Revert the conversion we did from a non-masked set action to * masked set action. */ - if (nla_put(skb, OVS_ACTION_ATTR_SET, nla_len(a) - key_len, ovs_key)) + nla = nla_nest_start(skb, OVS_ACTION_ATTR_SET); + if (!nla) return -EMSGSIZE; + if (nla_put(skb, nla_type(ovs_key), key_len, nla_data(ovs_key))) + return -EMSGSIZE; + + nla_nest_end(skb, nla); return 0; } -- cgit v1.2.3-59-g8ed1b From add7d7596612bac594201da151a3ed6f8e94fc33 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 27 Feb 2015 10:04:11 -0500 Subject: drm/radeon: fix the audio dpms callbacks Don't touch the audio enable bits as these are already handled in display detection. Enable the hdmi secondary streams in hdmi enable to match dp. Rename dp dpms callback to be consistent with hdmi. bug: https://bugs.freedesktop.org/show_bug.cgi?id=89327 https://bugzilla.kernel.org/show_bug.cgi?id=93921 Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/dce6_afmt.c | 28 ++++++----------- drivers/gpu/drm/radeon/evergreen_hdmi.c | 55 ++++++++++++--------------------- drivers/gpu/drm/radeon/r600_hdmi.c | 11 ------- drivers/gpu/drm/radeon/radeon_audio.c | 8 ++--- 4 files changed, 32 insertions(+), 70 deletions(-) diff --git a/drivers/gpu/drm/radeon/dce6_afmt.c b/drivers/gpu/drm/radeon/dce6_afmt.c index 192c80389151..9de14cfc0e80 100644 --- a/drivers/gpu/drm/radeon/dce6_afmt.c +++ b/drivers/gpu/drm/radeon/dce6_afmt.c @@ -288,36 +288,26 @@ void dce6_dp_audio_set_dto(struct radeon_device *rdev, WREG32(DCCG_AUDIO_DTO1_MODULE, clock); } -void dce6_enable_dp_audio_packets(struct drm_encoder *encoder, bool enable) +void dce6_dp_enable(struct drm_encoder *encoder, bool enable) { struct drm_device *dev = encoder->dev; struct radeon_device *rdev = dev->dev_private; struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); struct radeon_encoder_atom_dig *dig = radeon_encoder->enc_priv; - uint32_t offset; if (!dig || !dig->afmt) return; - offset = dig->afmt->offset; - if (enable) { - if (dig->afmt->enabled) - return; - - WREG32(EVERGREEN_DP_SEC_TIMESTAMP + offset, EVERGREEN_DP_SEC_TIMESTAMP_MODE(1)); - WREG32(EVERGREEN_DP_SEC_CNTL + offset, - EVERGREEN_DP_SEC_ASP_ENABLE | /* Audio packet transmission */ - EVERGREEN_DP_SEC_ATP_ENABLE | /* Audio timestamp packet transmission */ - EVERGREEN_DP_SEC_AIP_ENABLE | /* Audio infoframe packet transmission */ - EVERGREEN_DP_SEC_STREAM_ENABLE); /* Master enable for secondary stream engine */ - radeon_audio_enable(rdev, dig->afmt->pin, true); + WREG32(EVERGREEN_DP_SEC_TIMESTAMP + dig->afmt->offset, + EVERGREEN_DP_SEC_TIMESTAMP_MODE(1)); + WREG32(EVERGREEN_DP_SEC_CNTL + dig->afmt->offset, + EVERGREEN_DP_SEC_ASP_ENABLE | /* Audio packet transmission */ + EVERGREEN_DP_SEC_ATP_ENABLE | /* Audio timestamp packet transmission */ + EVERGREEN_DP_SEC_AIP_ENABLE | /* Audio infoframe packet transmission */ + EVERGREEN_DP_SEC_STREAM_ENABLE); /* Master enable for secondary stream engine */ } else { - if (!dig->afmt->enabled) - return; - - WREG32(EVERGREEN_DP_SEC_CNTL + offset, 0); - radeon_audio_enable(rdev, dig->afmt->pin, false); + WREG32(EVERGREEN_DP_SEC_CNTL + dig->afmt->offset, 0); } dig->afmt->enabled = enable; diff --git a/drivers/gpu/drm/radeon/evergreen_hdmi.c b/drivers/gpu/drm/radeon/evergreen_hdmi.c index 1d9aebc79595..bdf2ca8b0be4 100644 --- a/drivers/gpu/drm/radeon/evergreen_hdmi.c +++ b/drivers/gpu/drm/radeon/evergreen_hdmi.c @@ -350,20 +350,9 @@ void dce4_set_audio_packet(struct drm_encoder *encoder, u32 offset) struct drm_device *dev = encoder->dev; struct radeon_device *rdev = dev->dev_private; - WREG32(HDMI_INFOFRAME_CONTROL0 + offset, - HDMI_AUDIO_INFO_SEND | /* enable audio info frames (frames won't be set until audio is enabled) */ - HDMI_AUDIO_INFO_CONT); /* required for audio info values to be updated */ - WREG32(AFMT_INFOFRAME_CONTROL0 + offset, AFMT_AUDIO_INFO_UPDATE); /* required for audio info values to be updated */ - WREG32(HDMI_INFOFRAME_CONTROL1 + offset, - HDMI_AUDIO_INFO_LINE(2)); /* anything other than 0 */ - - WREG32(HDMI_AUDIO_PACKET_CONTROL + offset, - HDMI_AUDIO_DELAY_EN(1) | /* set the default audio delay */ - HDMI_AUDIO_PACKETS_PER_LINE(3)); /* should be suffient for all audio modes and small enough for all hblanks */ - WREG32(AFMT_60958_0 + offset, AFMT_60958_CS_CHANNEL_NUMBER_L(1)); @@ -408,15 +397,19 @@ void evergreen_hdmi_enable(struct drm_encoder *encoder, bool enable) if (!dig || !dig->afmt) return; - /* Silent, r600_hdmi_enable will raise WARN for us */ - if (enable && dig->afmt->enabled) - return; - if (!enable && !dig->afmt->enabled) - return; + if (enable) { + WREG32(HDMI_INFOFRAME_CONTROL1 + dig->afmt->offset, + HDMI_AUDIO_INFO_LINE(2)); /* anything other than 0 */ - if (!enable && dig->afmt->pin) { - radeon_audio_enable(rdev, dig->afmt->pin, 0); - dig->afmt->pin = NULL; + WREG32(HDMI_AUDIO_PACKET_CONTROL + dig->afmt->offset, + HDMI_AUDIO_DELAY_EN(1) | /* set the default audio delay */ + HDMI_AUDIO_PACKETS_PER_LINE(3)); /* should be suffient for all audio modes and small enough for all hblanks */ + + WREG32(HDMI_INFOFRAME_CONTROL0 + dig->afmt->offset, + HDMI_AUDIO_INFO_SEND | /* enable audio info frames (frames won't be set until audio is enabled) */ + HDMI_AUDIO_INFO_CONT); /* required for audio info values to be updated */ + } else { + WREG32(HDMI_INFOFRAME_CONTROL0 + dig->afmt->offset, 0); } dig->afmt->enabled = enable; @@ -425,33 +418,28 @@ void evergreen_hdmi_enable(struct drm_encoder *encoder, bool enable) enable ? "En" : "Dis", dig->afmt->offset, radeon_encoder->encoder_id); } -void evergreen_enable_dp_audio_packets(struct drm_encoder *encoder, bool enable) +void evergreen_dp_enable(struct drm_encoder *encoder, bool enable) { struct drm_device *dev = encoder->dev; struct radeon_device *rdev = dev->dev_private; struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); struct radeon_encoder_atom_dig *dig = radeon_encoder->enc_priv; - uint32_t offset; if (!dig || !dig->afmt) return; - offset = dig->afmt->offset; - if (enable) { struct drm_connector *connector = radeon_get_connector_for_encoder(encoder); struct radeon_connector *radeon_connector = to_radeon_connector(connector); struct radeon_connector_atom_dig *dig_connector; uint32_t val; - if (dig->afmt->enabled) - return; - - WREG32(EVERGREEN_DP_SEC_TIMESTAMP + offset, EVERGREEN_DP_SEC_TIMESTAMP_MODE(1)); + WREG32(EVERGREEN_DP_SEC_TIMESTAMP + dig->afmt->offset, + EVERGREEN_DP_SEC_TIMESTAMP_MODE(1)); if (radeon_connector->con_priv) { dig_connector = radeon_connector->con_priv; - val = RREG32(EVERGREEN_DP_SEC_AUD_N + offset); + val = RREG32(EVERGREEN_DP_SEC_AUD_N + dig->afmt->offset); val &= ~EVERGREEN_DP_SEC_N_BASE_MULTIPLE(0xf); if (dig_connector->dp_clock == 162000) @@ -459,21 +447,16 @@ void evergreen_enable_dp_audio_packets(struct drm_encoder *encoder, bool enable) else val |= EVERGREEN_DP_SEC_N_BASE_MULTIPLE(5); - WREG32(EVERGREEN_DP_SEC_AUD_N + offset, val); + WREG32(EVERGREEN_DP_SEC_AUD_N + dig->afmt->offset, val); } - WREG32(EVERGREEN_DP_SEC_CNTL + offset, + WREG32(EVERGREEN_DP_SEC_CNTL + dig->afmt->offset, EVERGREEN_DP_SEC_ASP_ENABLE | /* Audio packet transmission */ EVERGREEN_DP_SEC_ATP_ENABLE | /* Audio timestamp packet transmission */ EVERGREEN_DP_SEC_AIP_ENABLE | /* Audio infoframe packet transmission */ EVERGREEN_DP_SEC_STREAM_ENABLE); /* Master enable for secondary stream engine */ - radeon_audio_enable(rdev, dig->afmt->pin, 0xf); } else { - if (!dig->afmt->enabled) - return; - - WREG32(EVERGREEN_DP_SEC_CNTL + offset, 0); - radeon_audio_enable(rdev, dig->afmt->pin, 0); + WREG32(EVERGREEN_DP_SEC_CNTL + dig->afmt->offset, 0); } dig->afmt->enabled = enable; diff --git a/drivers/gpu/drm/radeon/r600_hdmi.c b/drivers/gpu/drm/radeon/r600_hdmi.c index 62c91ed669ce..dd6606b8e23c 100644 --- a/drivers/gpu/drm/radeon/r600_hdmi.c +++ b/drivers/gpu/drm/radeon/r600_hdmi.c @@ -476,17 +476,6 @@ void r600_hdmi_enable(struct drm_encoder *encoder, bool enable) if (!dig || !dig->afmt) return; - /* Silent, r600_hdmi_enable will raise WARN for us */ - if (enable && dig->afmt->enabled) - return; - if (!enable && !dig->afmt->enabled) - return; - - if (!enable && dig->afmt->pin) { - radeon_audio_enable(rdev, dig->afmt->pin, 0); - dig->afmt->pin = NULL; - } - /* Older chipsets require setting HDMI and routing manually */ if (!ASIC_IS_DCE3(rdev)) { if (enable) diff --git a/drivers/gpu/drm/radeon/radeon_audio.c b/drivers/gpu/drm/radeon/radeon_audio.c index a3ceef6d9632..e4bb81245b9b 100644 --- a/drivers/gpu/drm/radeon/radeon_audio.c +++ b/drivers/gpu/drm/radeon/radeon_audio.c @@ -101,8 +101,8 @@ static void radeon_audio_dp_mode_set(struct drm_encoder *encoder, struct drm_display_mode *mode); void r600_hdmi_enable(struct drm_encoder *encoder, bool enable); void evergreen_hdmi_enable(struct drm_encoder *encoder, bool enable); -void evergreen_enable_dp_audio_packets(struct drm_encoder *encoder, bool enable); -void dce6_enable_dp_audio_packets(struct drm_encoder *encoder, bool enable); +void evergreen_dp_enable(struct drm_encoder *encoder, bool enable); +void dce6_dp_enable(struct drm_encoder *encoder, bool enable); static const u32 pin_offsets[7] = { @@ -210,7 +210,7 @@ static struct radeon_audio_funcs dce4_dp_funcs = { .set_avi_packet = evergreen_set_avi_packet, .set_audio_packet = dce4_set_audio_packet, .mode_set = radeon_audio_dp_mode_set, - .dpms = evergreen_enable_dp_audio_packets, + .dpms = evergreen_dp_enable, }; static struct radeon_audio_funcs dce6_hdmi_funcs = { @@ -240,7 +240,7 @@ static struct radeon_audio_funcs dce6_dp_funcs = { .set_avi_packet = evergreen_set_avi_packet, .set_audio_packet = dce4_set_audio_packet, .mode_set = radeon_audio_dp_mode_set, - .dpms = dce6_enable_dp_audio_packets, + .dpms = dce6_dp_enable, }; static void radeon_audio_interface_init(struct radeon_device *rdev) -- cgit v1.2.3-59-g8ed1b From d3c34d2c73481c39378dd91ec531564bb67a50df Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 27 Feb 2015 10:36:39 -0500 Subject: drm/radeon: assign pin in detect We need the pin from detect on, it's too late in dpms. Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/radeon_audio.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_audio.c b/drivers/gpu/drm/radeon/radeon_audio.c index e4bb81245b9b..713949487a66 100644 --- a/drivers/gpu/drm/radeon/radeon_audio.c +++ b/drivers/gpu/drm/radeon/radeon_audio.c @@ -452,7 +452,7 @@ void radeon_audio_enable(struct radeon_device *rdev, } void radeon_audio_detect(struct drm_connector *connector, - enum drm_connector_status status) + enum drm_connector_status status) { struct radeon_device *rdev; struct radeon_encoder *radeon_encoder; @@ -483,6 +483,7 @@ void radeon_audio_detect(struct drm_connector *connector, else radeon_encoder->audio = rdev->audio.hdmi_funcs; + dig->afmt->pin = radeon_audio_get_pin(connector->encoder); radeon_audio_write_speaker_allocation(connector->encoder); radeon_audio_write_sad_regs(connector->encoder); if (connector->encoder->crtc) @@ -491,6 +492,7 @@ void radeon_audio_detect(struct drm_connector *connector, radeon_audio_enable(rdev, dig->afmt->pin, 0xf); } else { radeon_audio_enable(rdev, dig->afmt->pin, 0); + dig->afmt->pin = NULL; } } @@ -704,7 +706,6 @@ static void radeon_audio_hdmi_mode_set(struct drm_encoder *encoder, return; /* disable audio prior to setting up hw */ - dig->afmt->pin = radeon_audio_get_pin(encoder); radeon_audio_enable(rdev, dig->afmt->pin, 0); radeon_audio_set_dto(encoder, mode->clock); @@ -734,7 +735,6 @@ static void radeon_audio_dp_mode_set(struct drm_encoder *encoder, return; /* disable audio prior to setting up hw */ - dig->afmt->pin = radeon_audio_get_pin(encoder); radeon_audio_enable(rdev, dig->afmt->pin, 0); radeon_audio_set_dto(encoder, rdev->clock.default_dispclk * 10); -- cgit v1.2.3-59-g8ed1b From 88af339f9fe285cb93c264adc75545a3d3b50470 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 27 Feb 2015 10:38:40 -0500 Subject: drm/radeon/audio: set mute around state setup To avoid possible sound artifacts while setting up audio. Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/radeon_audio.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_audio.c b/drivers/gpu/drm/radeon/radeon_audio.c index 713949487a66..5b579582175b 100644 --- a/drivers/gpu/drm/radeon/radeon_audio.c +++ b/drivers/gpu/drm/radeon/radeon_audio.c @@ -705,13 +705,13 @@ static void radeon_audio_hdmi_mode_set(struct drm_encoder *encoder, if (!dig || !dig->afmt) return; + radeon_audio_set_mute(encoder, true); /* disable audio prior to setting up hw */ radeon_audio_enable(rdev, dig->afmt->pin, 0); radeon_audio_set_dto(encoder, mode->clock); radeon_audio_set_vbi_packet(encoder); radeon_hdmi_set_color_depth(encoder); - radeon_audio_set_mute(encoder, false); radeon_audio_update_acr(encoder, mode->clock); radeon_audio_set_audio_packet(encoder); radeon_audio_select_pin(encoder); @@ -721,6 +721,7 @@ static void radeon_audio_hdmi_mode_set(struct drm_encoder *encoder, /* enable audio after to setting up hw */ radeon_audio_enable(rdev, dig->afmt->pin, 0xf); + radeon_audio_set_mute(encoder, false); } static void radeon_audio_dp_mode_set(struct drm_encoder *encoder, -- cgit v1.2.3-59-g8ed1b From 3ed7ceeabf4d6a6df02121cc7e4b46d39501b6e9 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 27 Feb 2015 10:42:21 -0500 Subject: drm/radeon: don't toggle audio state in modeset Should be done only at detect time to avoid spurious state changes on the audio side. Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/radeon_audio.c | 13 +------------ 1 file changed, 1 insertion(+), 12 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_audio.c b/drivers/gpu/drm/radeon/radeon_audio.c index 5b579582175b..c16191975916 100644 --- a/drivers/gpu/drm/radeon/radeon_audio.c +++ b/drivers/gpu/drm/radeon/radeon_audio.c @@ -696,9 +696,8 @@ static void radeon_audio_set_mute(struct drm_encoder *encoder, bool mute) * update the info frames with the data from the current display mode */ static void radeon_audio_hdmi_mode_set(struct drm_encoder *encoder, - struct drm_display_mode *mode) + struct drm_display_mode *mode) { - struct radeon_device *rdev = encoder->dev->dev_private; struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); struct radeon_encoder_atom_dig *dig = radeon_encoder->enc_priv; @@ -706,8 +705,6 @@ static void radeon_audio_hdmi_mode_set(struct drm_encoder *encoder, return; radeon_audio_set_mute(encoder, true); - /* disable audio prior to setting up hw */ - radeon_audio_enable(rdev, dig->afmt->pin, 0); radeon_audio_set_dto(encoder, mode->clock); radeon_audio_set_vbi_packet(encoder); @@ -719,8 +716,6 @@ static void radeon_audio_hdmi_mode_set(struct drm_encoder *encoder, if (radeon_audio_set_avi_packet(encoder, mode) < 0) return; - /* enable audio after to setting up hw */ - radeon_audio_enable(rdev, dig->afmt->pin, 0xf); radeon_audio_set_mute(encoder, false); } @@ -735,18 +730,12 @@ static void radeon_audio_dp_mode_set(struct drm_encoder *encoder, if (!dig || !dig->afmt) return; - /* disable audio prior to setting up hw */ - radeon_audio_enable(rdev, dig->afmt->pin, 0); - radeon_audio_set_dto(encoder, rdev->clock.default_dispclk * 10); radeon_audio_set_audio_packet(encoder); radeon_audio_select_pin(encoder); if (radeon_audio_set_avi_packet(encoder, mode) < 0) return; - - /* enable audio after to setting up hw */ - radeon_audio_enable(rdev, dig->afmt->pin, 0xf); } void radeon_audio_mode_set(struct drm_encoder *encoder, -- cgit v1.2.3-59-g8ed1b From b20932dd62f77a96124ec8f0c7ad0908b5584526 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 27 Feb 2015 10:51:40 -0500 Subject: drm/radeon/audio: update EDID derived fields in modeset We don't necessarily have an EDID at this point when audio detect gets called. Ideally we'd update these fields in detect, but that requires a larger rework of the display detect code. Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/radeon_audio.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_audio.c b/drivers/gpu/drm/radeon/radeon_audio.c index c16191975916..31de59271007 100644 --- a/drivers/gpu/drm/radeon/radeon_audio.c +++ b/drivers/gpu/drm/radeon/radeon_audio.c @@ -484,11 +484,6 @@ void radeon_audio_detect(struct drm_connector *connector, radeon_encoder->audio = rdev->audio.hdmi_funcs; dig->afmt->pin = radeon_audio_get_pin(connector->encoder); - radeon_audio_write_speaker_allocation(connector->encoder); - radeon_audio_write_sad_regs(connector->encoder); - if (connector->encoder->crtc) - radeon_audio_write_latency_fields(connector->encoder, - &connector->encoder->crtc->mode); radeon_audio_enable(rdev, dig->afmt->pin, 0xf); } else { radeon_audio_enable(rdev, dig->afmt->pin, 0); @@ -706,6 +701,9 @@ static void radeon_audio_hdmi_mode_set(struct drm_encoder *encoder, radeon_audio_set_mute(encoder, true); + radeon_audio_write_speaker_allocation(encoder); + radeon_audio_write_sad_regs(encoder); + radeon_audio_write_latency_fields(encoder, mode); radeon_audio_set_dto(encoder, mode->clock); radeon_audio_set_vbi_packet(encoder); radeon_hdmi_set_color_depth(encoder); @@ -730,6 +728,9 @@ static void radeon_audio_dp_mode_set(struct drm_encoder *encoder, if (!dig || !dig->afmt) return; + radeon_audio_write_speaker_allocation(encoder); + radeon_audio_write_sad_regs(encoder); + radeon_audio_write_latency_fields(encoder, mode); radeon_audio_set_dto(encoder, rdev->clock.default_dispclk * 10); radeon_audio_set_audio_packet(encoder); radeon_audio_select_pin(encoder); -- cgit v1.2.3-59-g8ed1b From aeefd07e90e277f9ac5c242c8b2e6797373021a3 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 27 Feb 2015 14:43:47 -0500 Subject: drm/radeon: properly set dto for dp on DCE4/5 If DCPLL or ext PLL is used, use the disp clk. If PPLL is used, use the dp clock. Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/evergreen_hdmi.c | 4 ++-- drivers/gpu/drm/radeon/radeon_audio.c | 9 ++++++++- 2 files changed, 10 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/radeon/evergreen_hdmi.c b/drivers/gpu/drm/radeon/evergreen_hdmi.c index bdf2ca8b0be4..c18d4ecbd95d 100644 --- a/drivers/gpu/drm/radeon/evergreen_hdmi.c +++ b/drivers/gpu/drm/radeon/evergreen_hdmi.c @@ -272,7 +272,7 @@ void dce4_hdmi_audio_set_dto(struct radeon_device *rdev, } void dce4_dp_audio_set_dto(struct radeon_device *rdev, - struct radeon_crtc *crtc, unsigned int clock) + struct radeon_crtc *crtc, unsigned int clock) { u32 value; @@ -294,7 +294,7 @@ void dce4_dp_audio_set_dto(struct radeon_device *rdev, * is the numerator, DCCG_AUDIO_DTOx_MODULE is the denominator */ WREG32(DCCG_AUDIO_DTO1_PHASE, 24000); - WREG32(DCCG_AUDIO_DTO1_MODULE, rdev->clock.max_pixel_clock * 10); + WREG32(DCCG_AUDIO_DTO1_MODULE, clock); } void dce4_set_vbi_packet(struct drm_encoder *encoder, u32 offset) diff --git a/drivers/gpu/drm/radeon/radeon_audio.c b/drivers/gpu/drm/radeon/radeon_audio.c index 31de59271007..b21ef69a34ac 100644 --- a/drivers/gpu/drm/radeon/radeon_audio.c +++ b/drivers/gpu/drm/radeon/radeon_audio.c @@ -724,6 +724,10 @@ static void radeon_audio_dp_mode_set(struct drm_encoder *encoder, struct radeon_device *rdev = dev->dev_private; struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); struct radeon_encoder_atom_dig *dig = radeon_encoder->enc_priv; + struct drm_connector *connector = radeon_get_connector_for_encoder(encoder); + struct radeon_connector *radeon_connector = to_radeon_connector(connector); + struct radeon_connector_atom_dig *dig_connector = + radeon_connector->con_priv; if (!dig || !dig->afmt) return; @@ -731,7 +735,10 @@ static void radeon_audio_dp_mode_set(struct drm_encoder *encoder, radeon_audio_write_speaker_allocation(encoder); radeon_audio_write_sad_regs(encoder); radeon_audio_write_latency_fields(encoder, mode); - radeon_audio_set_dto(encoder, rdev->clock.default_dispclk * 10); + if (rdev->clock.dp_extclk || ASIC_IS_DCE5(rdev)) + radeon_audio_set_dto(encoder, rdev->clock.default_dispclk * 10); + else + radeon_audio_set_dto(encoder, dig_connector->dp_clock); radeon_audio_set_audio_packet(encoder); radeon_audio_select_pin(encoder); -- cgit v1.2.3-59-g8ed1b From 5c046a57a5ecca7950943625a0cf5adfc601e861 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 27 Feb 2015 17:26:53 -0500 Subject: drm/radeon: adjust audio callback order - Move it out of the UNIPHY case to handle older DCE blocks. - set audio dpms before video dpms Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/atombios_encoders.c | 30 ++++++++++++++++-------------- 1 file changed, 16 insertions(+), 14 deletions(-) diff --git a/drivers/gpu/drm/radeon/atombios_encoders.c b/drivers/gpu/drm/radeon/atombios_encoders.c index 7fe7b749e182..c39c1d0d9d4e 100644 --- a/drivers/gpu/drm/radeon/atombios_encoders.c +++ b/drivers/gpu/drm/radeon/atombios_encoders.c @@ -1626,7 +1626,6 @@ radeon_atom_encoder_dpms_dig(struct drm_encoder *encoder, int mode) struct radeon_connector *radeon_connector = NULL; struct radeon_connector_atom_dig *radeon_dig_connector = NULL; bool travis_quirk = false; - int encoder_mode; if (connector) { radeon_connector = to_radeon_connector(connector); @@ -1722,13 +1721,6 @@ radeon_atom_encoder_dpms_dig(struct drm_encoder *encoder, int mode) } break; } - - encoder_mode = atombios_get_encoder_mode(encoder); - if (connector && (radeon_audio != 0) && - ((encoder_mode == ATOM_ENCODER_MODE_HDMI) || - (ENCODER_MODE_IS_DP(encoder_mode) && - drm_detect_monitor_audio(radeon_connector_edid(connector))))) - radeon_audio_dpms(encoder, mode); } static void @@ -1737,10 +1729,19 @@ radeon_atom_encoder_dpms(struct drm_encoder *encoder, int mode) struct drm_device *dev = encoder->dev; struct radeon_device *rdev = dev->dev_private; struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); + struct drm_connector *connector = radeon_get_connector_for_encoder(encoder); + int encoder_mode = atombios_get_encoder_mode(encoder); DRM_DEBUG_KMS("encoder dpms %d to mode %d, devices %08x, active_devices %08x\n", radeon_encoder->encoder_id, mode, radeon_encoder->devices, radeon_encoder->active_device); + + if (connector && (radeon_audio != 0) && + ((encoder_mode == ATOM_ENCODER_MODE_HDMI) || + (ENCODER_MODE_IS_DP(encoder_mode) && + drm_detect_monitor_audio(radeon_connector_edid(connector))))) + radeon_audio_dpms(encoder, mode); + switch (radeon_encoder->encoder_id) { case ENCODER_OBJECT_ID_INTERNAL_TMDS1: case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_TMDS1: @@ -2170,12 +2171,6 @@ radeon_atom_encoder_mode_set(struct drm_encoder *encoder, case ENCODER_OBJECT_ID_INTERNAL_UNIPHY3: case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA: /* handled in dpms */ - encoder_mode = atombios_get_encoder_mode(encoder); - if (connector && (radeon_audio != 0) && - ((encoder_mode == ATOM_ENCODER_MODE_HDMI) || - (ENCODER_MODE_IS_DP(encoder_mode) && - drm_detect_monitor_audio(radeon_connector_edid(connector))))) - radeon_audio_mode_set(encoder, adjusted_mode); break; case ENCODER_OBJECT_ID_INTERNAL_DDI: case ENCODER_OBJECT_ID_INTERNAL_DVO1: @@ -2197,6 +2192,13 @@ radeon_atom_encoder_mode_set(struct drm_encoder *encoder, } atombios_apply_encoder_quirks(encoder, adjusted_mode); + + encoder_mode = atombios_get_encoder_mode(encoder); + if (connector && (radeon_audio != 0) && + ((encoder_mode == ATOM_ENCODER_MODE_HDMI) || + (ENCODER_MODE_IS_DP(encoder_mode) && + drm_detect_monitor_audio(radeon_connector_edid(connector))))) + radeon_audio_mode_set(encoder, adjusted_mode); } static bool -- cgit v1.2.3-59-g8ed1b From b983a8f45898245c432afcfd7cf1bb34c5c4e577 Mon Sep 17 00:00:00 2001 From: Slava Grigorev Date: Mon, 2 Mar 2015 11:31:07 -0500 Subject: radeon/audio: fix whitespace Use proper tabs. Signed-off-by: Slava Grigorev Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/dce6_afmt.c | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) diff --git a/drivers/gpu/drm/radeon/dce6_afmt.c b/drivers/gpu/drm/radeon/dce6_afmt.c index 9de14cfc0e80..81a4f5405cd5 100644 --- a/drivers/gpu/drm/radeon/dce6_afmt.c +++ b/drivers/gpu/drm/radeon/dce6_afmt.c @@ -252,40 +252,40 @@ void dce6_audio_enable(struct radeon_device *rdev, void dce6_hdmi_audio_set_dto(struct radeon_device *rdev, struct radeon_crtc *crtc, unsigned int clock) { - /* Two dtos; generally use dto0 for HDMI */ + /* Two dtos; generally use dto0 for HDMI */ u32 value = 0; - if (crtc) + if (crtc) value |= DCCG_AUDIO_DTO0_SOURCE_SEL(crtc->crtc_id); WREG32(DCCG_AUDIO_DTO_SOURCE, value); - /* Express [24MHz / target pixel clock] as an exact rational - * number (coefficient of two integer numbers. DCCG_AUDIO_DTOx_PHASE - * is the numerator, DCCG_AUDIO_DTOx_MODULE is the denominator - */ - WREG32(DCCG_AUDIO_DTO0_PHASE, 24000); - WREG32(DCCG_AUDIO_DTO0_MODULE, clock); + /* Express [24MHz / target pixel clock] as an exact rational + * number (coefficient of two integer numbers. DCCG_AUDIO_DTOx_PHASE + * is the numerator, DCCG_AUDIO_DTOx_MODULE is the denominator + */ + WREG32(DCCG_AUDIO_DTO0_PHASE, 24000); + WREG32(DCCG_AUDIO_DTO0_MODULE, clock); } void dce6_dp_audio_set_dto(struct radeon_device *rdev, struct radeon_crtc *crtc, unsigned int clock) { - /* Two dtos; generally use dto1 for DP */ + /* Two dtos; generally use dto1 for DP */ u32 value = 0; value |= DCCG_AUDIO_DTO_SEL; - if (crtc) + if (crtc) value |= DCCG_AUDIO_DTO0_SOURCE_SEL(crtc->crtc_id); WREG32(DCCG_AUDIO_DTO_SOURCE, value); - /* Express [24MHz / target pixel clock] as an exact rational - * number (coefficient of two integer numbers. DCCG_AUDIO_DTOx_PHASE - * is the numerator, DCCG_AUDIO_DTOx_MODULE is the denominator - */ - WREG32(DCCG_AUDIO_DTO1_PHASE, 24000); - WREG32(DCCG_AUDIO_DTO1_MODULE, clock); + /* Express [24MHz / target pixel clock] as an exact rational + * number (coefficient of two integer numbers. DCCG_AUDIO_DTOx_PHASE + * is the numerator, DCCG_AUDIO_DTOx_MODULE is the denominator + */ + WREG32(DCCG_AUDIO_DTO1_PHASE, 24000); + WREG32(DCCG_AUDIO_DTO1_MODULE, clock); } void dce6_dp_enable(struct drm_encoder *encoder, bool enable) -- cgit v1.2.3-59-g8ed1b From 2afa3265b21ada7583bf4a69defe4539ad4df7cf Mon Sep 17 00:00:00 2001 From: Slava Grigorev Date: Mon, 2 Mar 2015 12:05:29 -0500 Subject: radeon/audio: fix DP audio on DCE6 Split DCE6 and DCE8 programming of DCCG_AUDIO_DTO1 registers to properly enable DP audio for both DCE revisions. Signed-off-by: Slava Grigorev Signed-off-by: Alex Deucher --- drivers/gpu/drm/radeon/dce6_afmt.c | 12 ++++++++++-- drivers/gpu/drm/radeon/sid.h | 4 ++-- 2 files changed, 12 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/radeon/dce6_afmt.c b/drivers/gpu/drm/radeon/dce6_afmt.c index 81a4f5405cd5..3adc2afe32aa 100644 --- a/drivers/gpu/drm/radeon/dce6_afmt.c +++ b/drivers/gpu/drm/radeon/dce6_afmt.c @@ -26,6 +26,9 @@ #include "radeon_audio.h" #include "sid.h" +#define DCE8_DCCG_AUDIO_DTO1_PHASE 0x05b8 +#define DCE8_DCCG_AUDIO_DTO1_MODULE 0x05bc + u32 dce6_endpoint_rreg(struct radeon_device *rdev, u32 block_offset, u32 reg) { @@ -284,8 +287,13 @@ void dce6_dp_audio_set_dto(struct radeon_device *rdev, * number (coefficient of two integer numbers. DCCG_AUDIO_DTOx_PHASE * is the numerator, DCCG_AUDIO_DTOx_MODULE is the denominator */ - WREG32(DCCG_AUDIO_DTO1_PHASE, 24000); - WREG32(DCCG_AUDIO_DTO1_MODULE, clock); + if (ASIC_IS_DCE8(rdev)) { + WREG32(DCE8_DCCG_AUDIO_DTO1_PHASE, 24000); + WREG32(DCE8_DCCG_AUDIO_DTO1_MODULE, clock); + } else { + WREG32(DCCG_AUDIO_DTO1_PHASE, 24000); + WREG32(DCCG_AUDIO_DTO1_MODULE, clock); + } } void dce6_dp_enable(struct drm_encoder *encoder, bool enable) diff --git a/drivers/gpu/drm/radeon/sid.h b/drivers/gpu/drm/radeon/sid.h index c27118cab16a..99a9835c9f61 100644 --- a/drivers/gpu/drm/radeon/sid.h +++ b/drivers/gpu/drm/radeon/sid.h @@ -912,8 +912,8 @@ #define DCCG_AUDIO_DTO0_PHASE 0x05b0 #define DCCG_AUDIO_DTO0_MODULE 0x05b4 -#define DCCG_AUDIO_DTO1_PHASE 0x05b8 -#define DCCG_AUDIO_DTO1_MODULE 0x05bc +#define DCCG_AUDIO_DTO1_PHASE 0x05c0 +#define DCCG_AUDIO_DTO1_MODULE 0x05c4 #define AFMT_AUDIO_SRC_CONTROL 0x713c #define AFMT_AUDIO_SRC_SELECT(x) (((x) & 7) << 0) -- cgit v1.2.3-59-g8ed1b From f957063fee6392bb9365370db6db74dc0b2dce0a Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 2 Mar 2015 20:36:26 -0500 Subject: drm/radeon: do a posting read in r100_set_irq To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741 Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/r100.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 279801ca5110..04f2514f7564 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -728,6 +728,10 @@ int r100_irq_set(struct radeon_device *rdev) tmp |= RADEON_FP2_DETECT_MASK; } WREG32(RADEON_GEN_INT_CNTL, tmp); + + /* read back to post the write */ + RREG32(RADEON_GEN_INT_CNTL); + return 0; } -- cgit v1.2.3-59-g8ed1b From 54acf107e4e66d1f4a697e08a7f60dba9fcf07c3 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 2 Mar 2015 20:39:56 -0500 Subject: drm/radeon: do a posting read in rs600_set_irq To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741 Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/rs600.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c index d81182ad53ec..97a904835759 100644 --- a/drivers/gpu/drm/radeon/rs600.c +++ b/drivers/gpu/drm/radeon/rs600.c @@ -694,6 +694,10 @@ int rs600_irq_set(struct radeon_device *rdev) WREG32(R_007D18_DC_HOT_PLUG_DETECT2_INT_CONTROL, hpd2); if (ASIC_IS_DCE2(rdev)) WREG32(R_007408_HDMI0_AUDIO_PACKET_CONTROL, hdmi0); + + /* posting read */ + RREG32(R_000040_GEN_INT_CNTL); + return 0; } -- cgit v1.2.3-59-g8ed1b From 9d1393f23d5656cdd5f368efd60694d4aeed81d3 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 2 Mar 2015 20:41:31 -0500 Subject: drm/radeon: do a posting read in r600_set_irq To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741 Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/r600.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/radeon/r600.c b/drivers/gpu/drm/radeon/r600.c index 07a71a2488c9..2fcad344492f 100644 --- a/drivers/gpu/drm/radeon/r600.c +++ b/drivers/gpu/drm/radeon/r600.c @@ -3784,6 +3784,9 @@ int r600_irq_set(struct radeon_device *rdev) WREG32(RV770_CG_THERMAL_INT, thermal_int); } + /* posting read */ + RREG32(R_000E50_SRBM_STATUS); + return 0; } -- cgit v1.2.3-59-g8ed1b From c320bb5f6dc0cb88a811cbaf839303e0a3916a92 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 2 Mar 2015 20:42:53 -0500 Subject: drm/radeon: do a posting read in evergreen_set_irq To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741 Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/evergreen.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/radeon/evergreen.c b/drivers/gpu/drm/radeon/evergreen.c index 4c0e24b3bb90..973df064c14f 100644 --- a/drivers/gpu/drm/radeon/evergreen.c +++ b/drivers/gpu/drm/radeon/evergreen.c @@ -4593,6 +4593,9 @@ int evergreen_irq_set(struct radeon_device *rdev) WREG32(AFMT_AUDIO_PACKET_CONTROL + EVERGREEN_CRTC4_REGISTER_OFFSET, afmt5); WREG32(AFMT_AUDIO_PACKET_CONTROL + EVERGREEN_CRTC5_REGISTER_OFFSET, afmt6); + /* posting read */ + RREG32(SRBM_STATUS); + return 0; } -- cgit v1.2.3-59-g8ed1b From 0586915ec10d0ae60de5cd3381ad25a704760402 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 2 Mar 2015 20:43:53 -0500 Subject: drm/radeon: do a posting read in si_set_irq To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741 Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/si.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/radeon/si.c b/drivers/gpu/drm/radeon/si.c index bcf516a8a2f1..e088e5558da0 100644 --- a/drivers/gpu/drm/radeon/si.c +++ b/drivers/gpu/drm/radeon/si.c @@ -6203,6 +6203,9 @@ int si_irq_set(struct radeon_device *rdev) WREG32(CG_THERMAL_INT, thermal_int); + /* posting read */ + RREG32(SRBM_STATUS); + return 0; } -- cgit v1.2.3-59-g8ed1b From cffefd9bb31cd35ab745d3b49005d10616d25bdc Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 2 Mar 2015 20:45:24 -0500 Subject: drm/radeon: do a posting read in cik_set_irq To make sure the writes go through the pci bridge. bug: https://bugzilla.kernel.org/show_bug.cgi?id=90741 Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/cik.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/radeon/cik.c b/drivers/gpu/drm/radeon/cik.c index 0c993da9c8fb..3e670d344a20 100644 --- a/drivers/gpu/drm/radeon/cik.c +++ b/drivers/gpu/drm/radeon/cik.c @@ -7555,6 +7555,9 @@ int cik_irq_set(struct radeon_device *rdev) WREG32(DC_HPD5_INT_CONTROL, hpd5); WREG32(DC_HPD6_INT_CONTROL, hpd6); + /* posting read */ + RREG32(SRBM_STATUS); + return 0; } -- cgit v1.2.3-59-g8ed1b From a28b2a47edcd0cb7c051b445f71a426000394606 Mon Sep 17 00:00:00 2001 From: Tommi Rantala Date: Mon, 2 Mar 2015 21:36:07 +0200 Subject: drm/radeon: fix DRM_IOCTL_RADEON_CS oops MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Passing zeroed drm_radeon_cs struct to DRM_IOCTL_RADEON_CS produces the following oops. Fix by always calling INIT_LIST_HEAD() to avoid the crash in list_sort(). ---------------------------------- #include #include #include #include #include static const struct drm_radeon_cs cs; int main(int argc, char **argv) { return ioctl(open(argv[1], O_RDWR), DRM_IOCTL_RADEON_CS, &cs); } ---------------------------------- [ttrantal@test2 ~]$ ./main /dev/dri/card0 [ 46.904650] BUG: unable to handle kernel NULL pointer dereference at (null) [ 46.905022] IP: [] list_sort+0x42/0x240 [ 46.905022] PGD 68f29067 PUD 688b5067 PMD 0 [ 46.905022] Oops: 0002 [#1] SMP [ 46.905022] CPU: 0 PID: 2413 Comm: main Not tainted 4.0.0-rc1+ #58 [ 46.905022] Hardware name: Hewlett-Packard HP Compaq dc5750 Small Form Factor/0A64h, BIOS 786E3 v02.10 01/25/2007 [ 46.905022] task: ffff880058e2bcc0 ti: ffff880058e64000 task.ti: ffff880058e64000 [ 46.905022] RIP: 0010:[] [] list_sort+0x42/0x240 [ 46.905022] RSP: 0018:ffff880058e67998 EFLAGS: 00010246 [ 46.905022] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 [ 46.905022] RDX: ffffffff81644410 RSI: ffff880058e67b40 RDI: ffff880058e67a58 [ 46.905022] RBP: ffff880058e67a88 R08: 0000000000000000 R09: 0000000000000000 [ 46.905022] R10: ffff880058e2bcc0 R11: ffffffff828e6ca0 R12: ffffffff81644410 [ 46.905022] R13: ffff8800694b8018 R14: 0000000000000000 R15: ffff880058e679b0 [ 46.905022] FS: 00007fdc65a65700(0000) GS:ffff88006d600000(0000) knlGS:0000000000000000 [ 46.905022] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 46.905022] CR2: 0000000000000000 CR3: 0000000058dd9000 CR4: 00000000000006f0 [ 46.905022] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 46.905022] DR3: 0000000000000000 DR6: 00000000ffff4ff0 DR7: 0000000000000400 [ 46.905022] Stack: [ 46.905022] ffff880058e67b40 ffff880058e2bcc0 ffff880058e67a78 0000000000000000 [ 46.905022] 0000000000000000 0000000000000000 0000000000000000 0000000000000000 [ 46.905022] 0000000000000000 0000000000000000 0000000000000000 0000000000000000 [ 46.905022] Call Trace: [ 46.905022] [] radeon_cs_parser_fini+0x195/0x220 [ 46.905022] [] radeon_cs_ioctl+0xa9/0x960 [ 46.905022] [] drm_ioctl+0x19c/0x640 [ 46.905022] [] ? trace_hardirqs_on_caller+0xfd/0x1c0 [ 46.905022] [] ? trace_hardirqs_on+0xd/0x10 [ 46.905022] [] radeon_drm_ioctl+0x46/0x80 [ 46.905022] [] do_vfs_ioctl+0x318/0x570 [ 46.905022] [] ? selinux_file_ioctl+0x56/0x110 [ 46.905022] [] SyS_ioctl+0x81/0xa0 [ 46.905022] [] system_call_fastpath+0x12/0x17 [ 46.905022] Code: 48 89 b5 10 ff ff ff 0f 84 03 01 00 00 4c 8d bd 28 ff ff ff 31 c0 48 89 fb b9 15 00 00 00 49 89 d4 4c 89 ff f3 48 ab 48 8b 46 08 <48> c7 00 00 00 00 00 48 8b 0e 48 85 c9 0f 84 7d 00 00 00 c7 85 [ 46.905022] RIP [] list_sort+0x42/0x240 [ 46.905022] RSP [ 46.905022] CR2: 0000000000000000 [ 47.149253] ---[ end trace 09576b4e8b2c20b8 ]--- Reviewed-by: Christian König Signed-off-by: Tommi Rantala Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/radeon_cs.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_cs.c b/drivers/gpu/drm/radeon/radeon_cs.c index a579ed379f20..4d0f96cc3da4 100644 --- a/drivers/gpu/drm/radeon/radeon_cs.c +++ b/drivers/gpu/drm/radeon/radeon_cs.c @@ -256,11 +256,13 @@ int radeon_cs_parser_init(struct radeon_cs_parser *p, void *data) u32 ring = RADEON_CS_RING_GFX; s32 priority = 0; + INIT_LIST_HEAD(&p->validated); + if (!cs->num_chunks) { return 0; } + /* get chunks */ - INIT_LIST_HEAD(&p->validated); p->idx = 0; p->ib.sa_bo = NULL; p->const_ib.sa_bo = NULL; -- cgit v1.2.3-59-g8ed1b From 77ae5f4b48a0445426c9c1ef7c0f28b717e35d55 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Tue, 3 Mar 2015 17:00:43 -0500 Subject: drm/radeon: fix interlaced modes on DCE8 Need to double the viewport height. Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org --- drivers/gpu/drm/radeon/atombios_crtc.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c index ed644a4f6f57..86807ee91bd1 100644 --- a/drivers/gpu/drm/radeon/atombios_crtc.c +++ b/drivers/gpu/drm/radeon/atombios_crtc.c @@ -1405,6 +1405,9 @@ static int dce4_crtc_do_set_base(struct drm_crtc *crtc, (x << 16) | y); viewport_w = crtc->mode.hdisplay; viewport_h = (crtc->mode.vdisplay + 1) & ~1; + if ((rdev->family >= CHIP_BONAIRE) && + (crtc->mode.flags & DRM_MODE_FLAG_INTERLACE)) + viewport_h *= 2; WREG32(EVERGREEN_VIEWPORT_SIZE + radeon_crtc->crtc_offset, (viewport_w << 16) | viewport_h); -- cgit v1.2.3-59-g8ed1b From 48d66b9749e39e0d4cc37d635df3f18906af38a6 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Tue, 3 Mar 2015 20:28:59 -0500 Subject: NFSv4: Fix a race in NFSv4.1 server trunking discovery We do not want to allow a race with another NFS mount to cause nfs41_walk_client_list() to establish a lease on our nfs_client before we're done checking for trunking. Signed-off-by: Trond Myklebust --- fs/nfs/client.c | 2 +- fs/nfs/nfs4client.c | 9 ++++----- fs/nfs/nfs4state.c | 14 ++++++++++++-- 3 files changed, 17 insertions(+), 8 deletions(-) diff --git a/fs/nfs/client.c b/fs/nfs/client.c index f9f4845db989..19874151e95c 100644 --- a/fs/nfs/client.c +++ b/fs/nfs/client.c @@ -433,7 +433,7 @@ static struct nfs_client *nfs_match_client(const struct nfs_client_initdata *dat static bool nfs_client_init_is_complete(const struct nfs_client *clp) { - return clp->cl_cons_state != NFS_CS_INITING; + return clp->cl_cons_state <= NFS_CS_READY; } int nfs_wait_client_init_complete(const struct nfs_client *clp) diff --git a/fs/nfs/nfs4client.c b/fs/nfs/nfs4client.c index 8646af9b11d2..86d6214ea022 100644 --- a/fs/nfs/nfs4client.c +++ b/fs/nfs/nfs4client.c @@ -621,6 +621,9 @@ int nfs41_walk_client_list(struct nfs_client *new, spin_lock(&nn->nfs_client_lock); list_for_each_entry(pos, &nn->nfs_client_list, cl_share_link) { + if (pos == new) + goto found; + if (pos->rpc_ops != new->rpc_ops) continue; @@ -639,10 +642,6 @@ int nfs41_walk_client_list(struct nfs_client *new, prev = pos; status = nfs_wait_client_init_complete(pos); - if (pos->cl_cons_state == NFS_CS_SESSION_INITING) { - nfs4_schedule_lease_recovery(pos); - status = nfs4_wait_clnt_recover(pos); - } spin_lock(&nn->nfs_client_lock); if (status < 0) break; @@ -668,7 +667,7 @@ int nfs41_walk_client_list(struct nfs_client *new, */ if (!nfs4_match_client_owner_id(pos, new)) continue; - +found: atomic_inc(&pos->cl_count); *result = pos; status = 0; diff --git a/fs/nfs/nfs4state.c b/fs/nfs/nfs4state.c index 5ad908e9ce9c..d8b43f0e08fc 100644 --- a/fs/nfs/nfs4state.c +++ b/fs/nfs/nfs4state.c @@ -346,9 +346,19 @@ int nfs41_discover_server_trunking(struct nfs_client *clp, status = nfs4_proc_exchange_id(clp, cred); if (status != NFS4_OK) return status; - set_bit(NFS4CLNT_LEASE_CONFIRM, &clp->cl_state); - return nfs41_walk_client_list(clp, result, cred); + status = nfs41_walk_client_list(clp, result, cred); + if (status < 0) + return status; + if (clp != *result) + return 0; + + set_bit(NFS4CLNT_LEASE_CONFIRM, &clp->cl_state); + nfs4_schedule_state_manager(clp); + status = nfs_wait_client_init_complete(clp); + if (status < 0) + nfs_put_client(clp); + return status; } #endif /* CONFIG_NFS_V4_1 */ -- cgit v1.2.3-59-g8ed1b From 875ebe940d77a41682c367ad799b4f39f128d3fa Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Tue, 24 Feb 2015 17:58:02 +1100 Subject: powerpc/smp: Wait until secondaries are active & online Anton has a busy ppc64le KVM box where guests sometimes hit the infamous "kernel BUG at kernel/smpboot.c:134!" issue during boot: BUG_ON(td->cpu != smp_processor_id()); Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops output confirms it: CPU: 0 Comm: watchdog/130 The problem is that we aren't ensuring the CPU active bit is set for the secondary before allowing the master to continue on. The master unparks the secondary CPU's kthreads and the scheduler looks for a CPU to run on. It calls select_task_rq() and realises the suggested CPU is not in the cpus_allowed mask. It then ends up in select_fallback_rq(), and since the active bit isnt't set we choose some other CPU to run on. This seems to have been introduced by 6acbfb96976f "sched: Fix hotplug vs. set_cpus_allowed_ptr()", which changed from setting active before online to setting active after online. However that was in turn fixing a bug where other code assumed an active CPU was also online, so we can't just revert that fix. The simplest fix is just to spin waiting for both active & online to be set. We already have a barrier prior to set_cpu_online() (which also sets active), to ensure all other setup is completed before online & active are set. Fixes: 6acbfb96976f ("sched: Fix hotplug vs. set_cpus_allowed_ptr()") Signed-off-by: Michael Ellerman Signed-off-by: Anton Blanchard Signed-off-by: Michael Ellerman --- arch/powerpc/kernel/smp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/kernel/smp.c b/arch/powerpc/kernel/smp.c index 6e19afa35a15..ec9ec2058d2d 100644 --- a/arch/powerpc/kernel/smp.c +++ b/arch/powerpc/kernel/smp.c @@ -541,8 +541,8 @@ int __cpu_up(unsigned int cpu, struct task_struct *tidle) if (smp_ops->give_timebase) smp_ops->give_timebase(); - /* Wait until cpu puts itself in the online map */ - while (!cpu_online(cpu)) + /* Wait until cpu puts itself in the online & active maps */ + while (!cpu_online(cpu) || !cpu_active(cpu)) cpu_relax(); return 0; -- cgit v1.2.3-59-g8ed1b From 4ad04e5987115ece5fa8a0cf1dc72fcd4707e33e Mon Sep 17 00:00:00 2001 From: Nishanth Aravamudan Date: Sat, 21 Feb 2015 11:00:50 -0800 Subject: powerpc/iommu: Remove IOMMU device references via bus notifier After d905c5df9aef ("PPC: POWERNV: move iommu_add_device earlier"), the refcnt on the kobject backing the IOMMU group for a PCI device is elevated by each call to pci_dma_dev_setup_pSeriesLP() (via set_iommu_table_base_and_group). When we go to dlpar a multi-function PCI device out: iommu_reconfig_notifier -> iommu_free_table -> iommu_group_put BUG_ON(tbl->it_group) We trip this BUG_ON, because there are still references on the table, so it is not freed. Fix this by moving the powernv bus notifier to common code and calling it for both powernv and pseries. Fixes: d905c5df9aef ("PPC: POWERNV: move iommu_add_device earlier") Signed-off-by: Nishanth Aravamudan Tested-by: Nishanth Aravamudan Signed-off-by: Michael Ellerman --- arch/powerpc/include/asm/iommu.h | 6 ++++++ arch/powerpc/kernel/iommu.c | 26 ++++++++++++++++++++++++++ arch/powerpc/platforms/powernv/pci.c | 26 -------------------------- arch/powerpc/platforms/pseries/iommu.c | 2 ++ 4 files changed, 34 insertions(+), 26 deletions(-) diff --git a/arch/powerpc/include/asm/iommu.h b/arch/powerpc/include/asm/iommu.h index 9cfa3706a1b8..f1ea5972f6ec 100644 --- a/arch/powerpc/include/asm/iommu.h +++ b/arch/powerpc/include/asm/iommu.h @@ -113,6 +113,7 @@ extern void iommu_register_group(struct iommu_table *tbl, int pci_domain_number, unsigned long pe_num); extern int iommu_add_device(struct device *dev); extern void iommu_del_device(struct device *dev); +extern int __init tce_iommu_bus_notifier_init(void); #else static inline void iommu_register_group(struct iommu_table *tbl, int pci_domain_number, @@ -128,6 +129,11 @@ static inline int iommu_add_device(struct device *dev) static inline void iommu_del_device(struct device *dev) { } + +static inline int __init tce_iommu_bus_notifier_init(void) +{ + return 0; +} #endif /* !CONFIG_IOMMU_API */ static inline void set_iommu_table_base_and_group(struct device *dev, diff --git a/arch/powerpc/kernel/iommu.c b/arch/powerpc/kernel/iommu.c index 5d3968c4d799..b054f33ab1fb 100644 --- a/arch/powerpc/kernel/iommu.c +++ b/arch/powerpc/kernel/iommu.c @@ -1175,4 +1175,30 @@ void iommu_del_device(struct device *dev) } EXPORT_SYMBOL_GPL(iommu_del_device); +static int tce_iommu_bus_notifier(struct notifier_block *nb, + unsigned long action, void *data) +{ + struct device *dev = data; + + switch (action) { + case BUS_NOTIFY_ADD_DEVICE: + return iommu_add_device(dev); + case BUS_NOTIFY_DEL_DEVICE: + if (dev->iommu_group) + iommu_del_device(dev); + return 0; + default: + return 0; + } +} + +static struct notifier_block tce_iommu_bus_nb = { + .notifier_call = tce_iommu_bus_notifier, +}; + +int __init tce_iommu_bus_notifier_init(void) +{ + bus_register_notifier(&pci_bus_type, &tce_iommu_bus_nb); + return 0; +} #endif /* CONFIG_IOMMU_API */ diff --git a/arch/powerpc/platforms/powernv/pci.c b/arch/powerpc/platforms/powernv/pci.c index e69142f4af08..54323d6b5166 100644 --- a/arch/powerpc/platforms/powernv/pci.c +++ b/arch/powerpc/platforms/powernv/pci.c @@ -836,30 +836,4 @@ void __init pnv_pci_init(void) #endif } -static int tce_iommu_bus_notifier(struct notifier_block *nb, - unsigned long action, void *data) -{ - struct device *dev = data; - - switch (action) { - case BUS_NOTIFY_ADD_DEVICE: - return iommu_add_device(dev); - case BUS_NOTIFY_DEL_DEVICE: - if (dev->iommu_group) - iommu_del_device(dev); - return 0; - default: - return 0; - } -} - -static struct notifier_block tce_iommu_bus_nb = { - .notifier_call = tce_iommu_bus_notifier, -}; - -static int __init tce_iommu_bus_notifier_init(void) -{ - bus_register_notifier(&pci_bus_type, &tce_iommu_bus_nb); - return 0; -} machine_subsys_initcall_sync(powernv, tce_iommu_bus_notifier_init); diff --git a/arch/powerpc/platforms/pseries/iommu.c b/arch/powerpc/platforms/pseries/iommu.c index 1d3d52dc3ff3..7803a19adb31 100644 --- a/arch/powerpc/platforms/pseries/iommu.c +++ b/arch/powerpc/platforms/pseries/iommu.c @@ -1340,3 +1340,5 @@ static int __init disable_multitce(char *str) } __setup("multitce=", disable_multitce); + +machine_subsys_initcall_sync(pseries, tce_iommu_bus_notifier_init); -- cgit v1.2.3-59-g8ed1b From e11259f920d8cb3550e0f311c064bdabe1bc3aaf Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Tue, 3 Mar 2015 20:35:31 -0500 Subject: NFSv4.1: Clear the old state by our client id before establishing a new lease If the call to exchange-id returns with the EXCHGID4_FLAG_CONFIRMED_R flag set, then that means our lease was established by a previous mount instance. Ensure that we detect this situation, and that we clear the state held by that mount. Reported-by: Jorge Mora Signed-off-by: Trond Myklebust --- fs/nfs/nfs4proc.c | 15 +++++++++++---- fs/nfs/nfs4session.h | 1 + fs/nfs/nfs4state.c | 6 +++++- 3 files changed, 17 insertions(+), 5 deletions(-) diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index 732526e04cd5..627f37c44456 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -6897,9 +6897,13 @@ static int _nfs4_proc_exchange_id(struct nfs_client *clp, struct rpc_cred *cred, if (status == 0) { clp->cl_clientid = res.clientid; - clp->cl_exchange_flags = (res.flags & ~EXCHGID4_FLAG_CONFIRMED_R); - if (!(res.flags & EXCHGID4_FLAG_CONFIRMED_R)) + clp->cl_exchange_flags = res.flags; + /* Client ID is not confirmed */ + if (!(res.flags & EXCHGID4_FLAG_CONFIRMED_R)) { + clear_bit(NFS4_SESSION_ESTABLISHED, + &clp->cl_session->session_state); clp->cl_seqid = res.seqid; + } kfree(clp->cl_serverowner); clp->cl_serverowner = res.server_owner; @@ -7231,6 +7235,9 @@ static void nfs4_update_session(struct nfs4_session *session, struct nfs41_create_session_res *res) { nfs4_copy_sessionid(&session->sess_id, &res->sessionid); + /* Mark client id and session as being confirmed */ + session->clp->cl_exchange_flags |= EXCHGID4_FLAG_CONFIRMED_R; + set_bit(NFS4_SESSION_ESTABLISHED, &session->session_state); session->flags = res->flags; memcpy(&session->fc_attrs, &res->fc_attrs, sizeof(session->fc_attrs)); if (res->flags & SESSION4_BACK_CHAN) @@ -7326,8 +7333,8 @@ int nfs4_proc_destroy_session(struct nfs4_session *session, dprintk("--> nfs4_proc_destroy_session\n"); /* session is still being setup */ - if (session->clp->cl_cons_state != NFS_CS_READY) - return status; + if (!test_and_clear_bit(NFS4_SESSION_ESTABLISHED, &session->session_state)) + return 0; status = rpc_call_sync(session->clp->cl_rpcclient, &msg, RPC_TASK_TIMEOUT); trace_nfs4_destroy_session(session->clp, status); diff --git a/fs/nfs/nfs4session.h b/fs/nfs/nfs4session.h index fc46c7455898..e3ea2c5324d6 100644 --- a/fs/nfs/nfs4session.h +++ b/fs/nfs/nfs4session.h @@ -70,6 +70,7 @@ struct nfs4_session { enum nfs4_session_state { NFS4_SESSION_INITING, + NFS4_SESSION_ESTABLISHED, }; extern int nfs4_setup_slot_table(struct nfs4_slot_table *tbl, diff --git a/fs/nfs/nfs4state.c b/fs/nfs/nfs4state.c index d8b43f0e08fc..f95e3b58bbc3 100644 --- a/fs/nfs/nfs4state.c +++ b/fs/nfs/nfs4state.c @@ -353,7 +353,11 @@ int nfs41_discover_server_trunking(struct nfs_client *clp, if (clp != *result) return 0; - set_bit(NFS4CLNT_LEASE_CONFIRM, &clp->cl_state); + /* Purge state if the client id was established in a prior instance */ + if (clp->cl_exchange_flags & EXCHGID4_FLAG_CONFIRMED_R) + set_bit(NFS4CLNT_PURGE_STATE, &clp->cl_state); + else + set_bit(NFS4CLNT_LEASE_CONFIRM, &clp->cl_state); nfs4_schedule_state_manager(clp); status = nfs_wait_client_init_complete(clp); if (status < 0) -- cgit v1.2.3-59-g8ed1b From 54fc7c1c961cb39edfe31f8a3f5ba6414e134b37 Mon Sep 17 00:00:00 2001 From: Chris Wilson Date: Thu, 26 Feb 2015 15:53:02 +0000 Subject: drm/i915: Check for driver readyness before handling an underrun interrupt When we takeover from the BIOS and install our interrupt handler, the BIOS may have left us a few surprises in the form of spontaneous interrupts. (This is especially likely on hardware like 965gm where display fifo underruns are continuous and the GMCH cannot filter that interrupt souce.) As we enable our IRQ early so that we can use it during hardware probing, our interrupt handler must be prepared to handle a few sources prior to being fully configured. As such, we need to add a simple is-ready check prior to dereferencing our KMS state for reporting underruns. Reported-by: Rob Clark Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1193972 Signed-off-by: Chris Wilson Reviewed-by: Daniel Vetter Cc: stable@vger.kernel.org [Jani: dropped the extra !] Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/intel_fifo_underrun.c | 18 +++++++----------- 1 file changed, 7 insertions(+), 11 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_fifo_underrun.c b/drivers/gpu/drm/i915/intel_fifo_underrun.c index 04e248dd2259..54daa66c6970 100644 --- a/drivers/gpu/drm/i915/intel_fifo_underrun.c +++ b/drivers/gpu/drm/i915/intel_fifo_underrun.c @@ -282,16 +282,6 @@ bool intel_set_cpu_fifo_underrun_reporting(struct drm_i915_private *dev_priv, return ret; } -static bool -__cpu_fifo_underrun_reporting_enabled(struct drm_i915_private *dev_priv, - enum pipe pipe) -{ - struct drm_crtc *crtc = dev_priv->pipe_to_crtc_mapping[pipe]; - struct intel_crtc *intel_crtc = to_intel_crtc(crtc); - - return !intel_crtc->cpu_fifo_underrun_disabled; -} - /** * intel_set_pch_fifo_underrun_reporting - set PCH fifo underrun reporting state * @dev_priv: i915 device instance @@ -352,9 +342,15 @@ bool intel_set_pch_fifo_underrun_reporting(struct drm_i915_private *dev_priv, void intel_cpu_fifo_underrun_irq_handler(struct drm_i915_private *dev_priv, enum pipe pipe) { + struct drm_crtc *crtc = dev_priv->pipe_to_crtc_mapping[pipe]; + + /* We may be called too early in init, thanks BIOS! */ + if (crtc == NULL) + return; + /* GMCH can't disable fifo underruns, filter them. */ if (HAS_GMCH_DISPLAY(dev_priv->dev) && - !__cpu_fifo_underrun_reporting_enabled(dev_priv, pipe)) + to_intel_crtc(crtc)->cpu_fifo_underrun_disabled) return; if (intel_set_cpu_fifo_underrun_reporting(dev_priv, pipe, false)) -- cgit v1.2.3-59-g8ed1b From ab3be73fa7b43f4c3648ce29b5fd649ea54d3adb Mon Sep 17 00:00:00 2001 From: Imre Deak Date: Mon, 2 Mar 2015 13:04:41 +0200 Subject: drm/i915: gen4: work around hang during hibernation MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Bjørn reported that his machine hang during hibernation and eventually bisected the problem to the following commit: commit da2bc1b9db3351addd293e5b82757efe1f77ed1d Author: Imre Deak Date: Thu Oct 23 19:23:26 2014 +0300 drm/i915: add poweroff_late handler The problem seems to be that after the kernel puts the device into D3 the BIOS still tries to access it, or otherwise assumes that it's in D0. This is clearly bogus, since ACPI mandates that devices are put into D3 by the OSPM if they are not wake-up sources. In the future we want to unify more of the driver's runtime and system suspend paths, for example by skipping all the system suspend/hibernation hooks if the device is runtime suspended already. Accordingly for all other platforms the goal is still to properly power down the device during hibernation. v2: - Another GEN4 Lenovo laptop had the same issue, while platforms from other vendors (including mobile and desktop, GEN4 and non-GEN4) seem to work fine. Based on this apply the workaround on all GEN4 Lenovo platforms. - add code comment about failing platforms (Ville) Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-February/060633.html Reported-and-bisected-by: Bjørn Mork Cc: stable@vger.kernel.org # v3.19 Signed-off-by: Imre Deak Acked-by: Daniel Vetter Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/i915_drv.c | 30 +++++++++++++++++++++++++----- 1 file changed, 25 insertions(+), 5 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c index 8039cec71fc2..cc6ea53d2b81 100644 --- a/drivers/gpu/drm/i915/i915_drv.c +++ b/drivers/gpu/drm/i915/i915_drv.c @@ -622,7 +622,7 @@ static int i915_drm_suspend(struct drm_device *dev) return 0; } -static int i915_drm_suspend_late(struct drm_device *drm_dev) +static int i915_drm_suspend_late(struct drm_device *drm_dev, bool hibernation) { struct drm_i915_private *dev_priv = drm_dev->dev_private; int ret; @@ -636,7 +636,17 @@ static int i915_drm_suspend_late(struct drm_device *drm_dev) } pci_disable_device(drm_dev->pdev); - pci_set_power_state(drm_dev->pdev, PCI_D3hot); + /* + * During hibernation on some GEN4 platforms the BIOS may try to access + * the device even though it's already in D3 and hang the machine. So + * leave the device in D0 on those platforms and hope the BIOS will + * power down the device properly. Platforms where this was seen: + * Lenovo Thinkpad X301, X61s + */ + if (!(hibernation && + drm_dev->pdev->subsystem_vendor == PCI_VENDOR_ID_LENOVO && + INTEL_INFO(dev_priv)->gen == 4)) + pci_set_power_state(drm_dev->pdev, PCI_D3hot); return 0; } @@ -662,7 +672,7 @@ int i915_suspend_legacy(struct drm_device *dev, pm_message_t state) if (error) return error; - return i915_drm_suspend_late(dev); + return i915_drm_suspend_late(dev, false); } static int i915_drm_resume(struct drm_device *dev) @@ -950,7 +960,17 @@ static int i915_pm_suspend_late(struct device *dev) if (drm_dev->switch_power_state == DRM_SWITCH_POWER_OFF) return 0; - return i915_drm_suspend_late(drm_dev); + return i915_drm_suspend_late(drm_dev, false); +} + +static int i915_pm_poweroff_late(struct device *dev) +{ + struct drm_device *drm_dev = dev_to_i915(dev)->dev; + + if (drm_dev->switch_power_state == DRM_SWITCH_POWER_OFF) + return 0; + + return i915_drm_suspend_late(drm_dev, true); } static int i915_pm_resume_early(struct device *dev) @@ -1520,7 +1540,7 @@ static const struct dev_pm_ops i915_pm_ops = { .thaw_early = i915_pm_resume_early, .thaw = i915_pm_resume, .poweroff = i915_pm_suspend, - .poweroff_late = i915_pm_suspend_late, + .poweroff_late = i915_pm_poweroff_late, .restore_early = i915_pm_resume_early, .restore = i915_pm_resume, -- cgit v1.2.3-59-g8ed1b From 1eed601a5b02a1f0bbabd155aeea7879fc3708eb Mon Sep 17 00:00:00 2001 From: Qiao Zhou Date: Tue, 3 Mar 2015 09:16:08 +0800 Subject: dma: mmp-tdma: refine dma disable and dma-pos update Below are the refinements. 1. Set DMA abort bit when disabling dma channel. This will clear the remaining data in dma FIFO, to fix channel-swap issue. 2. Read DMA HW pointer when updating DMA status. Previously dma position is calculated by adding one period size in dma interrupt. This is inaccurate/insufficient for some high-quality audio APP. Since interrupt bottom half handler has variable schedule delay, it causes big error when calculating sample delay. Read the actual HW pointer and feedback can improve the accuracy. 3. Do some minor code clean. Signed-off-by: Qiao Zhou Signed-off-by: Vinod Koul --- drivers/dma/mmp_tdma.c | 31 +++++++++++++++++++++++++------ 1 file changed, 25 insertions(+), 6 deletions(-) diff --git a/drivers/dma/mmp_tdma.c b/drivers/dma/mmp_tdma.c index 70c2fa9963cd..b6f4e1fc9c78 100644 --- a/drivers/dma/mmp_tdma.c +++ b/drivers/dma/mmp_tdma.c @@ -110,7 +110,7 @@ struct mmp_tdma_chan { struct tasklet_struct tasklet; struct mmp_tdma_desc *desc_arr; - phys_addr_t desc_arr_phys; + dma_addr_t desc_arr_phys; int desc_num; enum dma_transfer_direction dir; dma_addr_t dev_addr; @@ -166,9 +166,12 @@ static void mmp_tdma_enable_chan(struct mmp_tdma_chan *tdmac) static int mmp_tdma_disable_chan(struct dma_chan *chan) { struct mmp_tdma_chan *tdmac = to_mmp_tdma_chan(chan); + u32 tdcr; - writel(readl(tdmac->reg_base + TDCR) & ~TDCR_CHANEN, - tdmac->reg_base + TDCR); + tdcr = readl(tdmac->reg_base + TDCR); + tdcr |= TDCR_ABR; + tdcr &= ~TDCR_CHANEN; + writel(tdcr, tdmac->reg_base + TDCR); tdmac->status = DMA_COMPLETE; @@ -296,12 +299,27 @@ static int mmp_tdma_clear_chan_irq(struct mmp_tdma_chan *tdmac) return -EAGAIN; } +static size_t mmp_tdma_get_pos(struct mmp_tdma_chan *tdmac) +{ + size_t reg; + + if (tdmac->idx == 0) { + reg = __raw_readl(tdmac->reg_base + TDSAR); + reg -= tdmac->desc_arr[0].src_addr; + } else if (tdmac->idx == 1) { + reg = __raw_readl(tdmac->reg_base + TDDAR); + reg -= tdmac->desc_arr[0].dst_addr; + } else + return -EINVAL; + + return reg; +} + static irqreturn_t mmp_tdma_chan_handler(int irq, void *dev_id) { struct mmp_tdma_chan *tdmac = dev_id; if (mmp_tdma_clear_chan_irq(tdmac) == 0) { - tdmac->pos = (tdmac->pos + tdmac->period_len) % tdmac->buf_len; tasklet_schedule(&tdmac->tasklet); return IRQ_HANDLED; } else @@ -343,7 +361,7 @@ static void mmp_tdma_free_descriptor(struct mmp_tdma_chan *tdmac) int size = tdmac->desc_num * sizeof(struct mmp_tdma_desc); gpool = tdmac->pool; - if (tdmac->desc_arr) + if (gpool && tdmac->desc_arr) gen_pool_free(gpool, (unsigned long)tdmac->desc_arr, size); tdmac->desc_arr = NULL; @@ -499,6 +517,7 @@ static enum dma_status mmp_tdma_tx_status(struct dma_chan *chan, { struct mmp_tdma_chan *tdmac = to_mmp_tdma_chan(chan); + tdmac->pos = mmp_tdma_get_pos(tdmac); dma_set_tx_state(txstate, chan->completed_cookie, chan->cookie, tdmac->buf_len - tdmac->pos); @@ -610,7 +629,7 @@ static int mmp_tdma_probe(struct platform_device *pdev) int i, ret; int irq = 0, irq_num = 0; int chan_num = TDMA_CHANNEL_NUM; - struct gen_pool *pool; + struct gen_pool *pool = NULL; of_id = of_match_device(mmp_tdma_dt_ids, &pdev->dev); if (of_id) -- cgit v1.2.3-59-g8ed1b From 63f1789ec71677dd285d43d6c79ca44808f16945 Mon Sep 17 00:00:00 2001 From: Jiang Liu Date: Wed, 4 Mar 2015 16:47:11 +0800 Subject: x86/PCI/ACPI: Ignore resources consumed by host bridge itself When parsing resources for PCI host bridge, we should ignore resources consumed by host bridge itself and only report window resources available to child PCI busses. Fixes: 593669c2ac0f (x86/PCI/ACPI: Use common ACPI resource interfaces ...) Signed-off-by: Jiang Liu Signed-off-by: Rafael J. Wysocki --- arch/x86/pci/acpi.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/arch/x86/pci/acpi.c b/arch/x86/pci/acpi.c index 6ac273832f28..e4695985f9de 100644 --- a/arch/x86/pci/acpi.c +++ b/arch/x86/pci/acpi.c @@ -331,7 +331,7 @@ static void probe_pci_root_info(struct pci_root_info *info, struct list_head *list) { int ret; - struct resource_entry *entry; + struct resource_entry *entry, *tmp; sprintf(info->name, "PCI Bus %04x:%02x", domain, busnum); info->bridge = device; @@ -345,8 +345,13 @@ static void probe_pci_root_info(struct pci_root_info *info, dev_dbg(&device->dev, "no IO and memory resources present in _CRS\n"); else - resource_list_for_each_entry(entry, list) - entry->res->name = info->name; + resource_list_for_each_entry_safe(entry, tmp, list) { + if ((entry->res->flags & IORESOURCE_WINDOW) == 0 || + (entry->res->flags & IORESOURCE_DISABLED)) + resource_list_destroy_entry(entry); + else + entry->res->name = info->name; + } } struct pci_bus *pci_acpi_scan_root(struct acpi_pci_root *root) -- cgit v1.2.3-59-g8ed1b From aa714d286f2ea5fae3ca8c75acd03d8694fb657e Mon Sep 17 00:00:00 2001 From: Jiang Liu Date: Wed, 4 Mar 2015 16:47:12 +0800 Subject: x86/PCI/ACPI: Relax ACPI resource descriptor checks to work around BIOS bugs Some BIOSes report incorrect length for ACPI address space descriptors, so relax the checks to avoid regressions. This issue has appeared several times as: 3162b6f0c5e1 ("PNPACPI: truncate _CRS windows with _LEN > _MAX - _MIN + 1") d558b483d5a7 ("x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1") f238b414a74a ("PNPACPI: compute Address Space length rather than using _LEN") 48728e077480 ("x86/PCI: compute Address Space length rather than using _LEN") Please refer to https://bugzilla.kernel.org/show_bug.cgi?id=94221 for more details and example malformed ACPI resource descriptors. Link: https://bugzilla.kernel.org/show_bug.cgi?id=94221 Fixes: 593669c2ac0f (x86/PCI/ACPI: Use common ACPI resource interfaces ...) Signed-off-by: Jiang Liu Tested-by: Dave Airlie Tested-by: Prakash Punnoor Signed-off-by: Rafael J. Wysocki --- drivers/acpi/resource.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/acpi/resource.c b/drivers/acpi/resource.c index c723668e3e27..5589a6e2a023 100644 --- a/drivers/acpi/resource.c +++ b/drivers/acpi/resource.c @@ -42,8 +42,10 @@ static bool acpi_dev_resource_len_valid(u64 start, u64 end, u64 len, bool io) * CHECKME: len might be required to check versus a minimum * length as well. 1 for io is fine, but for memory it does * not make any sense at all. + * Note: some BIOSes report incorrect length for ACPI address space + * descriptor, so remove check of 'reslen == len' to avoid regression. */ - if (len && reslen && reslen == len && start <= end) + if (len && reslen && start <= end) return true; pr_debug("ACPI: invalid or unassigned resource %s [%016llx - %016llx] length [%016llx]\n", -- cgit v1.2.3-59-g8ed1b From 5877b4f4677b66f92b5ed94491d69680d6eac4dc Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Wed, 4 Mar 2015 12:56:20 +0100 Subject: cpufreq: ppc: Add missing #include If CONFIG_SMP=n, does not include , causing: drivers/cpufreq/ppc-corenet-cpufreq.c: In function 'corenet_cpufreq_cpu_init': drivers/cpufreq/ppc-corenet-cpufreq.c:173:3: error: implicit declaration of function 'get_hard_smp_processor_id' [-Werror=implicit-function-declaration] Signed-off-by: Geert Uytterhoeven Signed-off-by: Rafael J. Wysocki --- drivers/cpufreq/ppc-corenet-cpufreq.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/cpufreq/ppc-corenet-cpufreq.c b/drivers/cpufreq/ppc-corenet-cpufreq.c index bee5df7794d3..7cb4b766cf94 100644 --- a/drivers/cpufreq/ppc-corenet-cpufreq.c +++ b/drivers/cpufreq/ppc-corenet-cpufreq.c @@ -22,6 +22,8 @@ #include #include +#include /* for get_hard_smp_processor_id() in UP configs */ + /** * struct cpu_data - per CPU data struct * @parent: the parent node of cpu clock -- cgit v1.2.3-59-g8ed1b From 66a5ca4b2c62c44692316f27b0fa39a037cce295 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 2 Mar 2015 11:24:28 -0800 Subject: PM / Domains: cleanup: rename gpd -> genpd in debugfs interface To keep consisitency with the rest of the file, use 'genpd' as the name of the 'struct generic_pm_domain' pointer instead of 'gpd'. This is just a rename, no functional changes. Signed-off-by: Kevin Hilman Acked-by: Pavel Machek Reviewed-by: Ulf Hansson Signed-off-by: Rafael J. Wysocki --- drivers/base/power/domain.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) diff --git a/drivers/base/power/domain.c b/drivers/base/power/domain.c index ba4abbe4693c..45937f88e77c 100644 --- a/drivers/base/power/domain.c +++ b/drivers/base/power/domain.c @@ -2242,7 +2242,7 @@ static void rtpm_status_str(struct seq_file *s, struct device *dev) } static int pm_genpd_summary_one(struct seq_file *s, - struct generic_pm_domain *gpd) + struct generic_pm_domain *genpd) { static const char * const status_lookup[] = { [GPD_STATE_ACTIVE] = "on", @@ -2256,26 +2256,26 @@ static int pm_genpd_summary_one(struct seq_file *s, struct gpd_link *link; int ret; - ret = mutex_lock_interruptible(&gpd->lock); + ret = mutex_lock_interruptible(&genpd->lock); if (ret) return -ERESTARTSYS; - if (WARN_ON(gpd->status >= ARRAY_SIZE(status_lookup))) + if (WARN_ON(genpd->status >= ARRAY_SIZE(status_lookup))) goto exit; - seq_printf(s, "%-30s %-15s ", gpd->name, status_lookup[gpd->status]); + seq_printf(s, "%-30s %-15s ", genpd->name, status_lookup[genpd->status]); /* * Modifications on the list require holding locks on both * master and slave, so we are safe. - * Also gpd->name is immutable. + * Also genpd->name is immutable. */ - list_for_each_entry(link, &gpd->master_links, master_node) { + list_for_each_entry(link, &genpd->master_links, master_node) { seq_printf(s, "%s", link->slave->name); - if (!list_is_last(&link->master_node, &gpd->master_links)) + if (!list_is_last(&link->master_node, &genpd->master_links)) seq_puts(s, ", "); } - list_for_each_entry(pm_data, &gpd->dev_list, list_node) { + list_for_each_entry(pm_data, &genpd->dev_list, list_node) { kobj_path = kobject_get_path(&pm_data->dev->kobj, GFP_KERNEL); if (kobj_path == NULL) continue; @@ -2287,14 +2287,14 @@ static int pm_genpd_summary_one(struct seq_file *s, seq_puts(s, "\n"); exit: - mutex_unlock(&gpd->lock); + mutex_unlock(&genpd->lock); return 0; } static int pm_genpd_summary_show(struct seq_file *s, void *data) { - struct generic_pm_domain *gpd; + struct generic_pm_domain *genpd; int ret = 0; seq_puts(s, " domain status slaves\n"); @@ -2305,8 +2305,8 @@ static int pm_genpd_summary_show(struct seq_file *s, void *data) if (ret) return -ERESTARTSYS; - list_for_each_entry(gpd, &gpd_list, gpd_list_node) { - ret = pm_genpd_summary_one(s, gpd); + list_for_each_entry(genpd, &gpd_list, gpd_list_node) { + ret = pm_genpd_summary_one(s, genpd); if (ret) break; } -- cgit v1.2.3-59-g8ed1b From 6e17cb12881ba8d5e456b89f072dc6b70048af36 Mon Sep 17 00:00:00 2001 From: Chris Wilson Date: Sun, 1 Mar 2015 10:41:37 +0000 Subject: ACPI / video: Load the module even if ACPI is disabled i915.ko depends upon the acpi/video.ko module and so refuses to load if ACPI is disabled at runtime if for example the BIOS is broken beyond repair. acpi/video provides an optional service for i915.ko and so we should just allow the modules to load, but do no nothing in order to let the machines boot correctly. Reported-by: Bill Augur Signed-off-by: Chris Wilson Cc: Daniel Vetter Cc: Jani Nikula Cc: All applicable Acked-by: Aaron Lu [ rjw: Fixed up the new comment in acpi_video_init() ] Signed-off-by: Rafael J. Wysocki --- drivers/acpi/video.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/acpi/video.c b/drivers/acpi/video.c index debd30917010..5f98ac69729a 100644 --- a/drivers/acpi/video.c +++ b/drivers/acpi/video.c @@ -2176,6 +2176,17 @@ EXPORT_SYMBOL(acpi_video_unregister_backlight); static int __init acpi_video_init(void) { + /* + * Let the module load even if ACPI is disabled (e.g. due to + * a broken BIOS) so that i915.ko can still be loaded on such + * old systems without an AcpiOpRegion. + * + * acpi_video_register() will report -ENODEV later as well due + * to acpi_disabled when i915.ko tries to register itself afterwards. + */ + if (acpi_disabled) + return 0; + dmi_check_system(video_dmi_table); if (intel_opregion_present()) -- cgit v1.2.3-59-g8ed1b From 28d634038d8fed8d25b92f21b728318a79c0be00 Mon Sep 17 00:00:00 2001 From: Chris Wilson Date: Sun, 1 Mar 2015 10:41:38 +0000 Subject: ACPI / video: Propagate the error code for acpi_video_register Report the actual error code from acpi_bus_register_driver(), it may help future debugging (typically ENODEV as previously reported, but the unusual cases are where it may help most). Signed-off-by: Chris Wilson Acked-by: Aaron Lu Signed-off-by: Rafael J. Wysocki --- drivers/acpi/video.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/acpi/video.c b/drivers/acpi/video.c index 5f98ac69729a..26eb70c8f518 100644 --- a/drivers/acpi/video.c +++ b/drivers/acpi/video.c @@ -2110,7 +2110,8 @@ static int __init intel_opregion_present(void) int acpi_video_register(void) { - int result = 0; + int ret; + if (register_count) { /* * if the function of acpi_video_register is already called, @@ -2122,9 +2123,9 @@ int acpi_video_register(void) mutex_init(&video_list_lock); INIT_LIST_HEAD(&video_bus_head); - result = acpi_bus_register_driver(&acpi_video_bus); - if (result < 0) - return -ENODEV; + ret = acpi_bus_register_driver(&acpi_video_bus); + if (ret) + return ret; /* * When the acpi_video_bus is loaded successfully, increase -- cgit v1.2.3-59-g8ed1b From d51199a83a2cf82a291d19ee852c44caa511427d Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Tue, 3 Mar 2015 13:38:14 +0200 Subject: ASoC: omap-pcm: Correct dma mask DMA_BIT_MASK of 64 is not valid dma address mask for OMAPs, it should be set to 32. The 64 was introduced by commit (in 2009): a152ff24b978 ASoC: OMAP: Make DMA 64 aligned But the dma_mask and coherent_dma_mask can not be used to specify alignment. Fixes: a152ff24b978 (ASoC: OMAP: Make DMA 64 aligned) Reported-by: Grygorii Strashko Signed-off-by: Peter Ujfalusi Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- sound/soc/omap/omap-pcm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/omap/omap-pcm.c b/sound/soc/omap/omap-pcm.c index f4b05bc23e4b..1343ecbf0bd5 100644 --- a/sound/soc/omap/omap-pcm.c +++ b/sound/soc/omap/omap-pcm.c @@ -201,7 +201,7 @@ static int omap_pcm_new(struct snd_soc_pcm_runtime *rtd) struct snd_pcm *pcm = rtd->pcm; int ret; - ret = dma_coerce_mask_and_coherent(card->dev, DMA_BIT_MASK(64)); + ret = dma_coerce_mask_and_coherent(card->dev, DMA_BIT_MASK(32)); if (ret) return ret; -- cgit v1.2.3-59-g8ed1b From 17f480342026e54000731acaa69bf32787ce46cb Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Fri, 27 Feb 2015 00:07:55 +0100 Subject: genirq / PM: Add flag for shared NO_SUSPEND interrupt lines It currently is required that all users of NO_SUSPEND interrupt lines pass the IRQF_NO_SUSPEND flag when requesting the IRQ or the WARN_ON_ONCE() in irq_pm_install_action() will trigger. That is done to warn about situations in which unprepared interrupt handlers may be run unnecessarily for suspended devices and may attempt to access those devices by mistake. However, it may cause drivers that have no technical reasons for using IRQF_NO_SUSPEND to set that flag just because they happen to share the interrupt line with something like a timer. Moreover, the generic handling of wakeup interrupts introduced by commit 9ce7a25849e8 (genirq: Simplify wakeup mechanism) only works for IRQs without any NO_SUSPEND users, so the drivers of wakeup devices needing to use shared NO_SUSPEND interrupt lines for signaling system wakeup generally have to detect wakeup in their interrupt handlers. Thus if they happen to share an interrupt line with a NO_SUSPEND user, they also need to request that their interrupt handlers be run after suspend_device_irqs(). In both cases the reason for using IRQF_NO_SUSPEND is not because the driver in question has a genuine need to run its interrupt handler after suspend_device_irqs(), but because it happens to share the line with some other NO_SUSPEND user. Otherwise, the driver would do without IRQF_NO_SUSPEND just fine. To make it possible to specify that condition explicitly, introduce a new IRQ action handler flag for shared IRQs, IRQF_COND_SUSPEND, that, when set, will indicate to the IRQ core that the interrupt user is generally fine with suspending the IRQ, but it also can tolerate handler invocations after suspend_device_irqs() and, in particular, it is capable of detecting system wakeup and triggering it as appropriate from its interrupt handler. That will allow us to work around a problem with a shared timer interrupt line on at91 platforms. Link: http://marc.info/?l=linux-kernel&m=142252777602084&w=2 Link: http://marc.info/?t=142252775300011&r=1&w=2 Link: https://lkml.org/lkml/2014/12/15/552 Reported-by: Boris Brezillon Signed-off-by: Rafael J. Wysocki Acked-by: Peter Zijlstra (Intel) Acked-by: Mark Rutland --- include/linux/interrupt.h | 5 +++++ include/linux/irqdesc.h | 1 + kernel/irq/manage.c | 7 ++++++- kernel/irq/pm.c | 7 ++++++- 4 files changed, 18 insertions(+), 2 deletions(-) diff --git a/include/linux/interrupt.h b/include/linux/interrupt.h index 606771c7cac2..2e88580194f0 100644 --- a/include/linux/interrupt.h +++ b/include/linux/interrupt.h @@ -59,6 +59,10 @@ * IRQF_NO_THREAD - Interrupt cannot be threaded * IRQF_EARLY_RESUME - Resume IRQ early during syscore instead of at device * resume time. + * IRQF_COND_SUSPEND - If the IRQ is shared with a NO_SUSPEND user, execute this + * interrupt handler after suspending interrupts. For system + * wakeup devices users need to implement wakeup detection in + * their interrupt handlers. */ #define IRQF_DISABLED 0x00000020 #define IRQF_SHARED 0x00000080 @@ -72,6 +76,7 @@ #define IRQF_FORCE_RESUME 0x00008000 #define IRQF_NO_THREAD 0x00010000 #define IRQF_EARLY_RESUME 0x00020000 +#define IRQF_COND_SUSPEND 0x00040000 #define IRQF_TIMER (__IRQF_TIMER | IRQF_NO_SUSPEND | IRQF_NO_THREAD) diff --git a/include/linux/irqdesc.h b/include/linux/irqdesc.h index faf433af425e..dd1109fb241e 100644 --- a/include/linux/irqdesc.h +++ b/include/linux/irqdesc.h @@ -78,6 +78,7 @@ struct irq_desc { #ifdef CONFIG_PM_SLEEP unsigned int nr_actions; unsigned int no_suspend_depth; + unsigned int cond_suspend_depth; unsigned int force_resume_depth; #endif #ifdef CONFIG_PROC_FS diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c index 196a06fbc122..886d09e691d5 100644 --- a/kernel/irq/manage.c +++ b/kernel/irq/manage.c @@ -1474,8 +1474,13 @@ int request_threaded_irq(unsigned int irq, irq_handler_t handler, * otherwise we'll have trouble later trying to figure out * which interrupt is which (messes up the interrupt freeing * logic etc). + * + * Also IRQF_COND_SUSPEND only makes sense for shared interrupts and + * it cannot be set along with IRQF_NO_SUSPEND. */ - if ((irqflags & IRQF_SHARED) && !dev_id) + if (((irqflags & IRQF_SHARED) && !dev_id) || + (!(irqflags & IRQF_SHARED) && (irqflags & IRQF_COND_SUSPEND)) || + ((irqflags & IRQF_NO_SUSPEND) && (irqflags & IRQF_COND_SUSPEND))) return -EINVAL; desc = irq_to_desc(irq); diff --git a/kernel/irq/pm.c b/kernel/irq/pm.c index 3ca532592704..5204a6d1b985 100644 --- a/kernel/irq/pm.c +++ b/kernel/irq/pm.c @@ -43,9 +43,12 @@ void irq_pm_install_action(struct irq_desc *desc, struct irqaction *action) if (action->flags & IRQF_NO_SUSPEND) desc->no_suspend_depth++; + else if (action->flags & IRQF_COND_SUSPEND) + desc->cond_suspend_depth++; WARN_ON_ONCE(desc->no_suspend_depth && - desc->no_suspend_depth != desc->nr_actions); + (desc->no_suspend_depth + + desc->cond_suspend_depth) != desc->nr_actions); } /* @@ -61,6 +64,8 @@ void irq_pm_remove_action(struct irq_desc *desc, struct irqaction *action) if (action->flags & IRQF_NO_SUSPEND) desc->no_suspend_depth--; + else if (action->flags & IRQF_COND_SUSPEND) + desc->cond_suspend_depth--; } static bool suspend_device_irq(struct irq_desc *desc, int irq) -- cgit v1.2.3-59-g8ed1b From 432ec92b299e4bcbb0d9a116789563d53b2798e1 Mon Sep 17 00:00:00 2001 From: Boris BREZILLON Date: Mon, 2 Mar 2015 10:18:13 +0100 Subject: PM / wakeup: export pm_system_wakeup symbol Export pm_system_wakeup function to allow irq handlers to deal with system wakeup. This is needed for shared IRQ lines where one of the handler is registered with IRQF_NO_SUSPEND, while the other ones want to configure it as a wakeup source. In this specific case, irq core does not handle the wakeup process and leave the decision to each irq handler. Signed-off-by: Boris Brezillon Reviewed-by: Alexandre Belloni Acked-by: Nicolas Ferre Acked-by: Mark Rutland Signed-off-by: Rafael J. Wysocki --- drivers/base/power/wakeup.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/base/power/wakeup.c b/drivers/base/power/wakeup.c index c2744b30d5d9..aab7158d2afe 100644 --- a/drivers/base/power/wakeup.c +++ b/drivers/base/power/wakeup.c @@ -730,6 +730,7 @@ void pm_system_wakeup(void) pm_abort_suspend = true; freeze_wake(); } +EXPORT_SYMBOL_GPL(pm_system_wakeup); void pm_wakeup_clear(void) { -- cgit v1.2.3-59-g8ed1b From 603b1a232604dcd19a28eaddf70eee9fbe3edc88 Mon Sep 17 00:00:00 2001 From: Boris BREZILLON Date: Mon, 2 Mar 2015 10:18:14 +0100 Subject: rtc: at91sam9: rework wakeup and interrupt handling The IRQ line used by the RTC device is usually shared with the system timer (PIT) on at91 platforms. Since timers are registering their handlers with IRQF_NO_SUSPEND, we should expect being called in suspended state, and properly wake the system up when this is the case. Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform irq core that it can safely be called while the system is suspended. Signed-off-by: Boris Brezillon Reviewed-by: Alexandre Belloni Acked-by: Nicolas Ferre Acked-by: Mark Rutland Signed-off-by: Rafael J. Wysocki --- drivers/rtc/rtc-at91sam9.c | 73 ++++++++++++++++++++++++++++++++++++++-------- 1 file changed, 61 insertions(+), 12 deletions(-) diff --git a/drivers/rtc/rtc-at91sam9.c b/drivers/rtc/rtc-at91sam9.c index 2183fd2750ab..5ccaee32df72 100644 --- a/drivers/rtc/rtc-at91sam9.c +++ b/drivers/rtc/rtc-at91sam9.c @@ -23,6 +23,7 @@ #include #include #include +#include #include /* @@ -77,6 +78,9 @@ struct sam9_rtc { unsigned int gpbr_offset; int irq; struct clk *sclk; + bool suspended; + unsigned long events; + spinlock_t lock; }; #define rtt_readl(rtc, field) \ @@ -271,14 +275,9 @@ static int at91_rtc_proc(struct device *dev, struct seq_file *seq) return 0; } -/* - * IRQ handler for the RTC - */ -static irqreturn_t at91_rtc_interrupt(int irq, void *_rtc) +static irqreturn_t at91_rtc_cache_events(struct sam9_rtc *rtc) { - struct sam9_rtc *rtc = _rtc; u32 sr, mr; - unsigned long events = 0; /* Shared interrupt may be for another device. Note: reading * SR clears it, so we must only read it in this irq handler! @@ -290,18 +289,54 @@ static irqreturn_t at91_rtc_interrupt(int irq, void *_rtc) /* alarm status */ if (sr & AT91_RTT_ALMS) - events |= (RTC_AF | RTC_IRQF); + rtc->events |= (RTC_AF | RTC_IRQF); /* timer update/increment */ if (sr & AT91_RTT_RTTINC) - events |= (RTC_UF | RTC_IRQF); + rtc->events |= (RTC_UF | RTC_IRQF); + + return IRQ_HANDLED; +} + +static void at91_rtc_flush_events(struct sam9_rtc *rtc) +{ + if (!rtc->events) + return; - rtc_update_irq(rtc->rtcdev, 1, events); + rtc_update_irq(rtc->rtcdev, 1, rtc->events); + rtc->events = 0; pr_debug("%s: num=%ld, events=0x%02lx\n", __func__, - events >> 8, events & 0x000000FF); + rtc->events >> 8, rtc->events & 0x000000FF); +} - return IRQ_HANDLED; +/* + * IRQ handler for the RTC + */ +static irqreturn_t at91_rtc_interrupt(int irq, void *_rtc) +{ + struct sam9_rtc *rtc = _rtc; + int ret; + + spin_lock(&rtc->lock); + + ret = at91_rtc_cache_events(rtc); + + /* We're called in suspended state */ + if (rtc->suspended) { + /* Mask irqs coming from this peripheral */ + rtt_writel(rtc, MR, + rtt_readl(rtc, MR) & + ~(AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN)); + /* Trigger a system wakeup */ + pm_system_wakeup(); + } else { + at91_rtc_flush_events(rtc); + } + + spin_unlock(&rtc->lock); + + return ret; } static const struct rtc_class_ops at91_rtc_ops = { @@ -421,7 +456,8 @@ static int at91_rtc_probe(struct platform_device *pdev) /* register irq handler after we know what name we'll use */ ret = devm_request_irq(&pdev->dev, rtc->irq, at91_rtc_interrupt, - IRQF_SHARED, dev_name(&rtc->rtcdev->dev), rtc); + IRQF_SHARED | IRQF_COND_SUSPEND, + dev_name(&rtc->rtcdev->dev), rtc); if (ret) { dev_dbg(&pdev->dev, "can't share IRQ %d?\n", rtc->irq); return ret; @@ -482,7 +518,12 @@ static int at91_rtc_suspend(struct device *dev) rtc->imr = mr & (AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN); if (rtc->imr) { if (device_may_wakeup(dev) && (mr & AT91_RTT_ALMIEN)) { + unsigned long flags; + enable_irq_wake(rtc->irq); + spin_lock_irqsave(&rtc->lock, flags); + rtc->suspended = true; + spin_unlock_irqrestore(&rtc->lock, flags); /* don't let RTTINC cause wakeups */ if (mr & AT91_RTT_RTTINCIEN) rtt_writel(rtc, MR, mr & ~AT91_RTT_RTTINCIEN); @@ -499,10 +540,18 @@ static int at91_rtc_resume(struct device *dev) u32 mr; if (rtc->imr) { + unsigned long flags; + if (device_may_wakeup(dev)) disable_irq_wake(rtc->irq); mr = rtt_readl(rtc, MR); rtt_writel(rtc, MR, mr | rtc->imr); + + spin_lock_irqsave(&rtc->lock, flags); + rtc->suspended = false; + at91_rtc_cache_events(rtc); + at91_rtc_flush_events(rtc); + spin_unlock_irqrestore(&rtc->lock, flags); } return 0; -- cgit v1.2.3-59-g8ed1b From dd1f1f391dd7f3a39a3983df2ca076871111cec9 Mon Sep 17 00:00:00 2001 From: Boris BREZILLON Date: Mon, 2 Mar 2015 10:18:15 +0100 Subject: rtc: at91rm9200: rework wakeup and interrupt handling The IRQ line used by the RTC device is usually shared with the system timer (PIT) on at91 platforms. Since timers are registering their handlers with IRQF_NO_SUSPEND, we should expect being called in suspended state, and properly wake the system up when this is the case. Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform irq core that it can safely be called while the system is suspended. Signed-off-by: Boris Brezillon Reviewed-by: Alexandre Belloni Acked-by: Nicolas Ferre Acked-by: Mark Rutland Signed-off-by: Rafael J. Wysocki --- drivers/rtc/rtc-at91rm9200.c | 62 ++++++++++++++++++++++++++++++++++---------- 1 file changed, 48 insertions(+), 14 deletions(-) diff --git a/drivers/rtc/rtc-at91rm9200.c b/drivers/rtc/rtc-at91rm9200.c index 70a5d94cc766..b4f7744f6751 100644 --- a/drivers/rtc/rtc-at91rm9200.c +++ b/drivers/rtc/rtc-at91rm9200.c @@ -31,6 +31,7 @@ #include #include #include +#include #include #include "rtc-at91rm9200.h" @@ -54,6 +55,10 @@ static void __iomem *at91_rtc_regs; static int irq; static DEFINE_SPINLOCK(at91_rtc_lock); static u32 at91_rtc_shadow_imr; +static bool suspended; +static DEFINE_SPINLOCK(suspended_lock); +static unsigned long cached_events; +static u32 at91_rtc_imr; static void at91_rtc_write_ier(u32 mask) { @@ -290,7 +295,9 @@ static irqreturn_t at91_rtc_interrupt(int irq, void *dev_id) struct rtc_device *rtc = platform_get_drvdata(pdev); unsigned int rtsr; unsigned long events = 0; + int ret = IRQ_NONE; + spin_lock(&suspended_lock); rtsr = at91_rtc_read(AT91_RTC_SR) & at91_rtc_read_imr(); if (rtsr) { /* this interrupt is shared! Is it ours? */ if (rtsr & AT91_RTC_ALARM) @@ -304,14 +311,22 @@ static irqreturn_t at91_rtc_interrupt(int irq, void *dev_id) at91_rtc_write(AT91_RTC_SCCR, rtsr); /* clear status reg */ - rtc_update_irq(rtc, 1, events); + if (!suspended) { + rtc_update_irq(rtc, 1, events); - dev_dbg(&pdev->dev, "%s(): num=%ld, events=0x%02lx\n", __func__, - events >> 8, events & 0x000000FF); + dev_dbg(&pdev->dev, "%s(): num=%ld, events=0x%02lx\n", + __func__, events >> 8, events & 0x000000FF); + } else { + cached_events |= events; + at91_rtc_write_idr(at91_rtc_imr); + pm_system_wakeup(); + } - return IRQ_HANDLED; + ret = IRQ_HANDLED; } - return IRQ_NONE; /* not handled */ + spin_lock(&suspended_lock); + + return ret; } static const struct at91_rtc_config at91rm9200_config = { @@ -401,8 +416,8 @@ static int __init at91_rtc_probe(struct platform_device *pdev) AT91_RTC_CALEV); ret = devm_request_irq(&pdev->dev, irq, at91_rtc_interrupt, - IRQF_SHARED, - "at91_rtc", pdev); + IRQF_SHARED | IRQF_COND_SUSPEND, + "at91_rtc", pdev); if (ret) { dev_err(&pdev->dev, "IRQ %d already in use.\n", irq); return ret; @@ -454,8 +469,6 @@ static void at91_rtc_shutdown(struct platform_device *pdev) /* AT91RM9200 RTC Power management control */ -static u32 at91_rtc_imr; - static int at91_rtc_suspend(struct device *dev) { /* this IRQ is shared with DBGU and other hardware which isn't @@ -464,21 +477,42 @@ static int at91_rtc_suspend(struct device *dev) at91_rtc_imr = at91_rtc_read_imr() & (AT91_RTC_ALARM|AT91_RTC_SECEV); if (at91_rtc_imr) { - if (device_may_wakeup(dev)) + if (device_may_wakeup(dev)) { + unsigned long flags; + enable_irq_wake(irq); - else + + spin_lock_irqsave(&suspended_lock, flags); + suspended = true; + spin_unlock_irqrestore(&suspended_lock, flags); + } else { at91_rtc_write_idr(at91_rtc_imr); + } } return 0; } static int at91_rtc_resume(struct device *dev) { + struct rtc_device *rtc = dev_get_drvdata(dev); + if (at91_rtc_imr) { - if (device_may_wakeup(dev)) + if (device_may_wakeup(dev)) { + unsigned long flags; + + spin_lock_irqsave(&suspended_lock, flags); + + if (cached_events) { + rtc_update_irq(rtc, 1, cached_events); + cached_events = 0; + } + + suspended = false; + spin_unlock_irqrestore(&suspended_lock, flags); + disable_irq_wake(irq); - else - at91_rtc_write_ier(at91_rtc_imr); + } + at91_rtc_write_ier(at91_rtc_imr); } return 0; } -- cgit v1.2.3-59-g8ed1b From 947f5b108543a6521728466ad5be6e2c4a35a65b Mon Sep 17 00:00:00 2001 From: Boris BREZILLON Date: Mon, 2 Mar 2015 10:18:16 +0100 Subject: clk: at91: implement suspend/resume for the PMC irqchip The irq line used by the PMC block is shared with several peripherals including the init timer which is registering its handler with IRQF_NO_SUSPEND. Implement the appropriate suspend/resume callback for the PMC irqchip, and inform irq core that PMC irq handler can be safely called while the system is suspended by setting IRQF_COND_SUSPEND. Signed-off-by: Boris Brezillon Reviewed-by: Alexandre Belloni Acked-by: Nicolas Ferre Acked-by: Mark Rutland Signed-off-by: Rafael J. Wysocki --- drivers/clk/at91/pmc.c | 20 +++++++++++++++++++- drivers/clk/at91/pmc.h | 1 + 2 files changed, 20 insertions(+), 1 deletion(-) diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c index f07c8152e5cc..3f27d21fb729 100644 --- a/drivers/clk/at91/pmc.c +++ b/drivers/clk/at91/pmc.c @@ -89,12 +89,29 @@ static int pmc_irq_set_type(struct irq_data *d, unsigned type) return 0; } +static void pmc_irq_suspend(struct irq_data *d) +{ + struct at91_pmc *pmc = irq_data_get_irq_chip_data(d); + + pmc->imr = pmc_read(pmc, AT91_PMC_IMR); + pmc_write(pmc, AT91_PMC_IDR, pmc->imr); +} + +static void pmc_irq_resume(struct irq_data *d) +{ + struct at91_pmc *pmc = irq_data_get_irq_chip_data(d); + + pmc_write(pmc, AT91_PMC_IER, pmc->imr); +} + static struct irq_chip pmc_irq = { .name = "PMC", .irq_disable = pmc_irq_mask, .irq_mask = pmc_irq_mask, .irq_unmask = pmc_irq_unmask, .irq_set_type = pmc_irq_set_type, + .irq_suspend = pmc_irq_suspend, + .irq_resume = pmc_irq_resume, }; static struct lock_class_key pmc_lock_class; @@ -224,7 +241,8 @@ static struct at91_pmc *__init at91_pmc_init(struct device_node *np, goto out_free_pmc; pmc_write(pmc, AT91_PMC_IDR, 0xffffffff); - if (request_irq(pmc->virq, pmc_irq_handler, IRQF_SHARED, "pmc", pmc)) + if (request_irq(pmc->virq, pmc_irq_handler, + IRQF_SHARED | IRQF_COND_SUSPEND, "pmc", pmc)) goto out_remove_irqdomain; return pmc; diff --git a/drivers/clk/at91/pmc.h b/drivers/clk/at91/pmc.h index 52d2041fa3f6..69abb08cf146 100644 --- a/drivers/clk/at91/pmc.h +++ b/drivers/clk/at91/pmc.h @@ -33,6 +33,7 @@ struct at91_pmc { spinlock_t lock; const struct at91_pmc_caps *caps; struct irq_domain *irqdomain; + u32 imr; }; static inline void pmc_lock(struct at91_pmc *pmc) -- cgit v1.2.3-59-g8ed1b From 0164bf0239777811bdc3e01f45501174dc6db19d Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Wed, 4 Mar 2015 17:34:32 -0500 Subject: locks: fix fasync_struct memory leak in lease upgrade/downgrade handling Commit 8634b51f6ca2 (locks: convert lease handling to file_lock_context) introduced a regression in the handling of lease upgrade/downgrades. In the event that we already have a lease on a file and are going to either upgrade or downgrade it, we skip doing any list insertion or deletion and simply re-call lm_setup on the existing lease. As of commit 8634b51f6ca2 however, we end up calling lm_setup on the lease that was passed in, instead of on the existing lease. This causes us to leak the fasync_struct that was allocated in the event that there was not already an existing one (as it always appeared that there wasn't one). Fixes: 8634b51f6ca2 (locks: convert lease handling to file_lock_context) Reported-and-Tested-by: Daniel Wagner Signed-off-by: Jeff Layton --- fs/locks.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/locks.c b/fs/locks.c index 365c82e1b3a9..f1bad681fc1c 100644 --- a/fs/locks.c +++ b/fs/locks.c @@ -1665,7 +1665,8 @@ generic_add_lease(struct file *filp, long arg, struct file_lock **flp, void **pr } if (my_fl != NULL) { - error = lease->fl_lmops->lm_change(my_fl, arg, &dispose); + lease = my_fl; + error = lease->fl_lmops->lm_change(lease, arg, &dispose); if (error) goto out; goto out_setup; -- cgit v1.2.3-59-g8ed1b From 440fd5283a87345cdd4237bdf45fb01130ea0056 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Fri, 23 Jan 2015 09:05:06 +0100 Subject: drm/mm: Support 4 GiB and larger ranges The current implementation is limited by the number of addresses that fit into an unsigned long. This causes problems on 32-bit Tegra where unsigned long is 32-bit but drm_mm is used to manage an IOVA space of 4 GiB. Given the 32-bit limitation, the range is limited to 4 GiB - 1 (or 4 GiB - 4 KiB for page granularity). This commit changes the start and size of the range to be an unsigned 64-bit integer, thus allowing much larger ranges to be supported. [airlied: fix i915 warnings and coloring callback] Signed-off-by: Thierry Reding Reviewed-by: Alex Deucher Reviewed-by: Chris Wilson Signed-off-by: Dave Airlie fixupo --- drivers/gpu/drm/drm_mm.c | 152 +++++++++++++++++++----------------- drivers/gpu/drm/i915/i915_debugfs.c | 4 +- drivers/gpu/drm/i915/i915_gem_gtt.c | 6 +- include/drm/drm_mm.h | 52 ++++++------ 4 files changed, 110 insertions(+), 104 deletions(-) diff --git a/drivers/gpu/drm/drm_mm.c b/drivers/gpu/drm/drm_mm.c index 04a209e2b66d..7fc6f8bd4821 100644 --- a/drivers/gpu/drm/drm_mm.c +++ b/drivers/gpu/drm/drm_mm.c @@ -91,29 +91,29 @@ */ static struct drm_mm_node *drm_mm_search_free_generic(const struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, enum drm_mm_search_flags flags); static struct drm_mm_node *drm_mm_search_free_in_range_generic(const struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, - unsigned long start, - unsigned long end, + u64 start, + u64 end, enum drm_mm_search_flags flags); static void drm_mm_insert_helper(struct drm_mm_node *hole_node, struct drm_mm_node *node, - unsigned long size, unsigned alignment, + u64 size, unsigned alignment, unsigned long color, enum drm_mm_allocator_flags flags) { struct drm_mm *mm = hole_node->mm; - unsigned long hole_start = drm_mm_hole_node_start(hole_node); - unsigned long hole_end = drm_mm_hole_node_end(hole_node); - unsigned long adj_start = hole_start; - unsigned long adj_end = hole_end; + u64 hole_start = drm_mm_hole_node_start(hole_node); + u64 hole_end = drm_mm_hole_node_end(hole_node); + u64 adj_start = hole_start; + u64 adj_end = hole_end; BUG_ON(node->allocated); @@ -124,12 +124,15 @@ static void drm_mm_insert_helper(struct drm_mm_node *hole_node, adj_start = adj_end - size; if (alignment) { - unsigned tmp = adj_start % alignment; - if (tmp) { + u64 tmp = adj_start; + unsigned rem; + + rem = do_div(tmp, alignment); + if (rem) { if (flags & DRM_MM_CREATE_TOP) - adj_start -= tmp; + adj_start -= rem; else - adj_start += alignment - tmp; + adj_start += alignment - rem; } } @@ -176,9 +179,9 @@ static void drm_mm_insert_helper(struct drm_mm_node *hole_node, int drm_mm_reserve_node(struct drm_mm *mm, struct drm_mm_node *node) { struct drm_mm_node *hole; - unsigned long end = node->start + node->size; - unsigned long hole_start; - unsigned long hole_end; + u64 end = node->start + node->size; + u64 hole_start; + u64 hole_end; BUG_ON(node == NULL); @@ -227,7 +230,7 @@ EXPORT_SYMBOL(drm_mm_reserve_node); * 0 on success, -ENOSPC if there's no suitable hole. */ int drm_mm_insert_node_generic(struct drm_mm *mm, struct drm_mm_node *node, - unsigned long size, unsigned alignment, + u64 size, unsigned alignment, unsigned long color, enum drm_mm_search_flags sflags, enum drm_mm_allocator_flags aflags) @@ -246,16 +249,16 @@ EXPORT_SYMBOL(drm_mm_insert_node_generic); static void drm_mm_insert_helper_range(struct drm_mm_node *hole_node, struct drm_mm_node *node, - unsigned long size, unsigned alignment, + u64 size, unsigned alignment, unsigned long color, - unsigned long start, unsigned long end, + u64 start, u64 end, enum drm_mm_allocator_flags flags) { struct drm_mm *mm = hole_node->mm; - unsigned long hole_start = drm_mm_hole_node_start(hole_node); - unsigned long hole_end = drm_mm_hole_node_end(hole_node); - unsigned long adj_start = hole_start; - unsigned long adj_end = hole_end; + u64 hole_start = drm_mm_hole_node_start(hole_node); + u64 hole_end = drm_mm_hole_node_end(hole_node); + u64 adj_start = hole_start; + u64 adj_end = hole_end; BUG_ON(!hole_node->hole_follows || node->allocated); @@ -271,12 +274,15 @@ static void drm_mm_insert_helper_range(struct drm_mm_node *hole_node, mm->color_adjust(hole_node, color, &adj_start, &adj_end); if (alignment) { - unsigned tmp = adj_start % alignment; - if (tmp) { + u64 tmp = adj_start; + unsigned rem; + + rem = do_div(tmp, alignment); + if (rem) { if (flags & DRM_MM_CREATE_TOP) - adj_start -= tmp; + adj_start -= rem; else - adj_start += alignment - tmp; + adj_start += alignment - rem; } } @@ -324,9 +330,9 @@ static void drm_mm_insert_helper_range(struct drm_mm_node *hole_node, * 0 on success, -ENOSPC if there's no suitable hole. */ int drm_mm_insert_node_in_range_generic(struct drm_mm *mm, struct drm_mm_node *node, - unsigned long size, unsigned alignment, + u64 size, unsigned alignment, unsigned long color, - unsigned long start, unsigned long end, + u64 start, u64 end, enum drm_mm_search_flags sflags, enum drm_mm_allocator_flags aflags) { @@ -387,32 +393,34 @@ void drm_mm_remove_node(struct drm_mm_node *node) } EXPORT_SYMBOL(drm_mm_remove_node); -static int check_free_hole(unsigned long start, unsigned long end, - unsigned long size, unsigned alignment) +static int check_free_hole(u64 start, u64 end, u64 size, unsigned alignment) { if (end - start < size) return 0; if (alignment) { - unsigned tmp = start % alignment; + u64 tmp = start; + unsigned rem; + + rem = do_div(tmp, alignment); if (tmp) - start += alignment - tmp; + start += alignment - rem; } return end >= start + size; } static struct drm_mm_node *drm_mm_search_free_generic(const struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, enum drm_mm_search_flags flags) { struct drm_mm_node *entry; struct drm_mm_node *best; - unsigned long adj_start; - unsigned long adj_end; - unsigned long best_size; + u64 adj_start; + u64 adj_end; + u64 best_size; BUG_ON(mm->scanned_blocks); @@ -421,7 +429,7 @@ static struct drm_mm_node *drm_mm_search_free_generic(const struct drm_mm *mm, __drm_mm_for_each_hole(entry, mm, adj_start, adj_end, flags & DRM_MM_SEARCH_BELOW) { - unsigned long hole_size = adj_end - adj_start; + u64 hole_size = adj_end - adj_start; if (mm->color_adjust) { mm->color_adjust(entry, color, &adj_start, &adj_end); @@ -445,18 +453,18 @@ static struct drm_mm_node *drm_mm_search_free_generic(const struct drm_mm *mm, } static struct drm_mm_node *drm_mm_search_free_in_range_generic(const struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, - unsigned long start, - unsigned long end, + u64 start, + u64 end, enum drm_mm_search_flags flags) { struct drm_mm_node *entry; struct drm_mm_node *best; - unsigned long adj_start; - unsigned long adj_end; - unsigned long best_size; + u64 adj_start; + u64 adj_end; + u64 best_size; BUG_ON(mm->scanned_blocks); @@ -465,7 +473,7 @@ static struct drm_mm_node *drm_mm_search_free_in_range_generic(const struct drm_ __drm_mm_for_each_hole(entry, mm, adj_start, adj_end, flags & DRM_MM_SEARCH_BELOW) { - unsigned long hole_size = adj_end - adj_start; + u64 hole_size = adj_end - adj_start; if (adj_start < start) adj_start = start; @@ -561,7 +569,7 @@ EXPORT_SYMBOL(drm_mm_replace_node); * adding/removing nodes to/from the scan list are allowed. */ void drm_mm_init_scan(struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color) { @@ -594,11 +602,11 @@ EXPORT_SYMBOL(drm_mm_init_scan); * adding/removing nodes to/from the scan list are allowed. */ void drm_mm_init_scan_with_range(struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, - unsigned long start, - unsigned long end) + u64 start, + u64 end) { mm->scan_color = color; mm->scan_alignment = alignment; @@ -627,8 +635,8 @@ bool drm_mm_scan_add_block(struct drm_mm_node *node) { struct drm_mm *mm = node->mm; struct drm_mm_node *prev_node; - unsigned long hole_start, hole_end; - unsigned long adj_start, adj_end; + u64 hole_start, hole_end; + u64 adj_start, adj_end; mm->scanned_blocks++; @@ -731,7 +739,7 @@ EXPORT_SYMBOL(drm_mm_clean); * * Note that @mm must be cleared to 0 before calling this function. */ -void drm_mm_init(struct drm_mm * mm, unsigned long start, unsigned long size) +void drm_mm_init(struct drm_mm * mm, u64 start, u64 size) { INIT_LIST_HEAD(&mm->hole_stack); mm->scanned_blocks = 0; @@ -766,18 +774,17 @@ void drm_mm_takedown(struct drm_mm * mm) } EXPORT_SYMBOL(drm_mm_takedown); -static unsigned long drm_mm_debug_hole(struct drm_mm_node *entry, - const char *prefix) +static u64 drm_mm_debug_hole(struct drm_mm_node *entry, + const char *prefix) { - unsigned long hole_start, hole_end, hole_size; + u64 hole_start, hole_end, hole_size; if (entry->hole_follows) { hole_start = drm_mm_hole_node_start(entry); hole_end = drm_mm_hole_node_end(entry); hole_size = hole_end - hole_start; - printk(KERN_DEBUG "%s 0x%08lx-0x%08lx: %8lu: free\n", - prefix, hole_start, hole_end, - hole_size); + pr_debug("%s %#llx-%#llx: %llu: free\n", prefix, hole_start, + hole_end, hole_size); return hole_size; } @@ -792,35 +799,34 @@ static unsigned long drm_mm_debug_hole(struct drm_mm_node *entry, void drm_mm_debug_table(struct drm_mm *mm, const char *prefix) { struct drm_mm_node *entry; - unsigned long total_used = 0, total_free = 0, total = 0; + u64 total_used = 0, total_free = 0, total = 0; total_free += drm_mm_debug_hole(&mm->head_node, prefix); drm_mm_for_each_node(entry, mm) { - printk(KERN_DEBUG "%s 0x%08lx-0x%08lx: %8lu: used\n", - prefix, entry->start, entry->start + entry->size, - entry->size); + pr_debug("%s %#llx-%#llx: %llu: used\n", prefix, entry->start, + entry->start + entry->size, entry->size); total_used += entry->size; total_free += drm_mm_debug_hole(entry, prefix); } total = total_free + total_used; - printk(KERN_DEBUG "%s total: %lu, used %lu free %lu\n", prefix, total, - total_used, total_free); + pr_debug("%s total: %llu, used %llu free %llu\n", prefix, total, + total_used, total_free); } EXPORT_SYMBOL(drm_mm_debug_table); #if defined(CONFIG_DEBUG_FS) -static unsigned long drm_mm_dump_hole(struct seq_file *m, struct drm_mm_node *entry) +static u64 drm_mm_dump_hole(struct seq_file *m, struct drm_mm_node *entry) { - unsigned long hole_start, hole_end, hole_size; + u64 hole_start, hole_end, hole_size; if (entry->hole_follows) { hole_start = drm_mm_hole_node_start(entry); hole_end = drm_mm_hole_node_end(entry); hole_size = hole_end - hole_start; - seq_printf(m, "0x%08lx-0x%08lx: 0x%08lx: free\n", - hole_start, hole_end, hole_size); + seq_printf(m, "%#llx-%#llx: %llu: free\n", hole_start, + hole_end, hole_size); return hole_size; } @@ -835,20 +841,20 @@ static unsigned long drm_mm_dump_hole(struct seq_file *m, struct drm_mm_node *en int drm_mm_dump_table(struct seq_file *m, struct drm_mm *mm) { struct drm_mm_node *entry; - unsigned long total_used = 0, total_free = 0, total = 0; + u64 total_used = 0, total_free = 0, total = 0; total_free += drm_mm_dump_hole(m, &mm->head_node); drm_mm_for_each_node(entry, mm) { - seq_printf(m, "0x%08lx-0x%08lx: 0x%08lx: used\n", - entry->start, entry->start + entry->size, - entry->size); + seq_printf(m, "%#016llx-%#016llx: %llu: used\n", entry->start, + entry->start + entry->size, entry->size); total_used += entry->size; total_free += drm_mm_dump_hole(m, entry); } total = total_free + total_used; - seq_printf(m, "total: %lu, used %lu free %lu\n", total, total_used, total_free); + seq_printf(m, "total: %llu, used %llu free %llu\n", total, + total_used, total_free); return 0; } EXPORT_SYMBOL(drm_mm_dump_table); diff --git a/drivers/gpu/drm/i915/i915_debugfs.c b/drivers/gpu/drm/i915/i915_debugfs.c index 96e811fe24ca..e8b18e542da4 100644 --- a/drivers/gpu/drm/i915/i915_debugfs.c +++ b/drivers/gpu/drm/i915/i915_debugfs.c @@ -152,12 +152,12 @@ describe_obj(struct seq_file *m, struct drm_i915_gem_object *obj) seq_puts(m, " (pp"); else seq_puts(m, " (g"); - seq_printf(m, "gtt offset: %08lx, size: %08lx, type: %u)", + seq_printf(m, "gtt offset: %08llx, size: %08llx, type: %u)", vma->node.start, vma->node.size, vma->ggtt_view.type); } if (obj->stolen) - seq_printf(m, " (stolen: %08lx)", obj->stolen->start); + seq_printf(m, " (stolen: %08llx)", obj->stolen->start); if (obj->pin_mappable || obj->fault_mappable) { char s[3], *t = s; if (obj->pin_mappable) diff --git a/drivers/gpu/drm/i915/i915_gem_gtt.c b/drivers/gpu/drm/i915/i915_gem_gtt.c index 746f77fb57a3..dccdc8aad2e2 100644 --- a/drivers/gpu/drm/i915/i915_gem_gtt.c +++ b/drivers/gpu/drm/i915/i915_gem_gtt.c @@ -1145,7 +1145,7 @@ static int gen6_ppgtt_init(struct i915_hw_ppgtt *ppgtt) ppgtt->base.clear_range(&ppgtt->base, 0, ppgtt->base.total, true); - DRM_DEBUG_DRIVER("Allocated pde space (%ldM) at GTT entry: %lx\n", + DRM_DEBUG_DRIVER("Allocated pde space (%lldM) at GTT entry: %llx\n", ppgtt->node.size >> 20, ppgtt->node.start / PAGE_SIZE); @@ -1713,8 +1713,8 @@ void i915_gem_gtt_finish_object(struct drm_i915_gem_object *obj) static void i915_gtt_color_adjust(struct drm_mm_node *node, unsigned long color, - unsigned long *start, - unsigned long *end) + u64 *start, + u64 *end) { if (node->color != color) *start += 4096; diff --git a/include/drm/drm_mm.h b/include/drm/drm_mm.h index a24addfdfcec..0de6290df4da 100644 --- a/include/drm/drm_mm.h +++ b/include/drm/drm_mm.h @@ -68,8 +68,8 @@ struct drm_mm_node { unsigned scanned_preceeds_hole : 1; unsigned allocated : 1; unsigned long color; - unsigned long start; - unsigned long size; + u64 start; + u64 size; struct drm_mm *mm; }; @@ -82,16 +82,16 @@ struct drm_mm { unsigned int scan_check_range : 1; unsigned scan_alignment; unsigned long scan_color; - unsigned long scan_size; - unsigned long scan_hit_start; - unsigned long scan_hit_end; + u64 scan_size; + u64 scan_hit_start; + u64 scan_hit_end; unsigned scanned_blocks; - unsigned long scan_start; - unsigned long scan_end; + u64 scan_start; + u64 scan_end; struct drm_mm_node *prev_scanned_node; void (*color_adjust)(struct drm_mm_node *node, unsigned long color, - unsigned long *start, unsigned long *end); + u64 *start, u64 *end); }; /** @@ -124,7 +124,7 @@ static inline bool drm_mm_initialized(struct drm_mm *mm) return mm->hole_stack.next; } -static inline unsigned long __drm_mm_hole_node_start(struct drm_mm_node *hole_node) +static inline u64 __drm_mm_hole_node_start(struct drm_mm_node *hole_node) { return hole_node->start + hole_node->size; } @@ -140,13 +140,13 @@ static inline unsigned long __drm_mm_hole_node_start(struct drm_mm_node *hole_no * Returns: * Start of the subsequent hole. */ -static inline unsigned long drm_mm_hole_node_start(struct drm_mm_node *hole_node) +static inline u64 drm_mm_hole_node_start(struct drm_mm_node *hole_node) { BUG_ON(!hole_node->hole_follows); return __drm_mm_hole_node_start(hole_node); } -static inline unsigned long __drm_mm_hole_node_end(struct drm_mm_node *hole_node) +static inline u64 __drm_mm_hole_node_end(struct drm_mm_node *hole_node) { return list_entry(hole_node->node_list.next, struct drm_mm_node, node_list)->start; @@ -163,7 +163,7 @@ static inline unsigned long __drm_mm_hole_node_end(struct drm_mm_node *hole_node * Returns: * End of the subsequent hole. */ -static inline unsigned long drm_mm_hole_node_end(struct drm_mm_node *hole_node) +static inline u64 drm_mm_hole_node_end(struct drm_mm_node *hole_node) { return __drm_mm_hole_node_end(hole_node); } @@ -222,7 +222,7 @@ int drm_mm_reserve_node(struct drm_mm *mm, struct drm_mm_node *node); int drm_mm_insert_node_generic(struct drm_mm *mm, struct drm_mm_node *node, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, enum drm_mm_search_flags sflags, @@ -245,7 +245,7 @@ int drm_mm_insert_node_generic(struct drm_mm *mm, */ static inline int drm_mm_insert_node(struct drm_mm *mm, struct drm_mm_node *node, - unsigned long size, + u64 size, unsigned alignment, enum drm_mm_search_flags flags) { @@ -255,11 +255,11 @@ static inline int drm_mm_insert_node(struct drm_mm *mm, int drm_mm_insert_node_in_range_generic(struct drm_mm *mm, struct drm_mm_node *node, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, - unsigned long start, - unsigned long end, + u64 start, + u64 end, enum drm_mm_search_flags sflags, enum drm_mm_allocator_flags aflags); /** @@ -282,10 +282,10 @@ int drm_mm_insert_node_in_range_generic(struct drm_mm *mm, */ static inline int drm_mm_insert_node_in_range(struct drm_mm *mm, struct drm_mm_node *node, - unsigned long size, + u64 size, unsigned alignment, - unsigned long start, - unsigned long end, + u64 start, + u64 end, enum drm_mm_search_flags flags) { return drm_mm_insert_node_in_range_generic(mm, node, size, alignment, @@ -296,21 +296,21 @@ static inline int drm_mm_insert_node_in_range(struct drm_mm *mm, void drm_mm_remove_node(struct drm_mm_node *node); void drm_mm_replace_node(struct drm_mm_node *old, struct drm_mm_node *new); void drm_mm_init(struct drm_mm *mm, - unsigned long start, - unsigned long size); + u64 start, + u64 size); void drm_mm_takedown(struct drm_mm *mm); bool drm_mm_clean(struct drm_mm *mm); void drm_mm_init_scan(struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color); void drm_mm_init_scan_with_range(struct drm_mm *mm, - unsigned long size, + u64 size, unsigned alignment, unsigned long color, - unsigned long start, - unsigned long end); + u64 start, + u64 end); bool drm_mm_scan_add_block(struct drm_mm_node *node); bool drm_mm_scan_remove_block(struct drm_mm_node *node); -- cgit v1.2.3-59-g8ed1b From 54c4cd68ed7abd9f245722bee39464d04ddb4cfd Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 4 Mar 2015 00:18:38 -0500 Subject: drm/ttm: device address space != CPU address space We need to store device offsets in 64 bit as the device address space may be larger than the CPU's. Fixes GPU init failures on radeons with 4GB or more of vram on 32 bit kernels. We put vram at the start of the GPU's address space so the gart aperture starts at 4 GB causing all GPU addresses in the gart aperture to get truncated. bug: https://bugs.freedesktop.org/show_bug.cgi?id=89072 [airlied: fix warning on nouveau build] Signed-off-by: Alex Deucher Cc: thellstrom@vmware.com Acked-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/nouveau/nouveau_fbcon.c | 2 +- drivers/gpu/drm/ttm/ttm_bo.c | 2 +- include/drm/ttm/ttm_bo_api.h | 2 +- include/drm/ttm/ttm_bo_driver.h | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/nouveau/nouveau_fbcon.c b/drivers/gpu/drm/nouveau/nouveau_fbcon.c index 79924e4b1b49..6751553abe4a 100644 --- a/drivers/gpu/drm/nouveau/nouveau_fbcon.c +++ b/drivers/gpu/drm/nouveau/nouveau_fbcon.c @@ -418,7 +418,7 @@ nouveau_fbcon_create(struct drm_fb_helper *helper, nouveau_fbcon_zfill(dev, fbcon); /* To allow resizeing without swapping buffers */ - NV_INFO(drm, "allocated %dx%d fb: 0x%lx, bo %p\n", + NV_INFO(drm, "allocated %dx%d fb: 0x%llx, bo %p\n", nouveau_fb->base.width, nouveau_fb->base.height, nvbo->bo.offset, nvbo); diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index d395b0bef73b..8d9b7de25613 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -74,7 +74,7 @@ static void ttm_mem_type_debug(struct ttm_bo_device *bdev, int mem_type) pr_err(" has_type: %d\n", man->has_type); pr_err(" use_type: %d\n", man->use_type); pr_err(" flags: 0x%08X\n", man->flags); - pr_err(" gpu_offset: 0x%08lX\n", man->gpu_offset); + pr_err(" gpu_offset: 0x%08llX\n", man->gpu_offset); pr_err(" size: %llu\n", man->size); pr_err(" available_caching: 0x%08X\n", man->available_caching); pr_err(" default_caching: 0x%08X\n", man->default_caching); diff --git a/include/drm/ttm/ttm_bo_api.h b/include/drm/ttm/ttm_bo_api.h index 0ccf7f267ff9..c768ddfbe53c 100644 --- a/include/drm/ttm/ttm_bo_api.h +++ b/include/drm/ttm/ttm_bo_api.h @@ -249,7 +249,7 @@ struct ttm_buffer_object { * either of these locks held. */ - unsigned long offset; + uint64_t offset; /* GPU address space is independent of CPU word size */ uint32_t cur_placement; struct sg_table *sg; diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h index 142d752fc450..813042cede57 100644 --- a/include/drm/ttm/ttm_bo_driver.h +++ b/include/drm/ttm/ttm_bo_driver.h @@ -277,7 +277,7 @@ struct ttm_mem_type_manager { bool has_type; bool use_type; uint32_t flags; - unsigned long gpu_offset; + uint64_t gpu_offset; /* GPU address space is independent of CPU word size */ uint64_t size; uint32_t available_caching; uint32_t default_caching; -- cgit v1.2.3-59-g8ed1b From 5db0f6e880eb99ad400d5f1c646dffc7fd939c78 Mon Sep 17 00:00:00 2001 From: Stephane Viau Date: Fri, 20 Feb 2015 12:40:58 -0500 Subject: drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes" Commit 0b776d457b94 ("drm/msm: fix fallout of atomic dpms changes") has a typo in both mdp5_encoder_helper_funcs and mdp5_crtc_helper_funcs definitions: .dpms entry should be replaced by .disable and .enable Also fixed a typo in mdp5_encoder_enable(). Note that these typos are only present for MDP5. MDP4 is fine. Signed-off-by: Stephane Viau Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c | 4 ++-- drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c | 6 +++--- 2 files changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c index 46fac545dc2b..946b71b6e608 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c @@ -544,8 +544,8 @@ static const struct drm_crtc_funcs mdp5_crtc_funcs = { static const struct drm_crtc_helper_funcs mdp5_crtc_helper_funcs = { .mode_fixup = mdp5_crtc_mode_fixup, .mode_set_nofb = mdp5_crtc_mode_set_nofb, - .prepare = mdp5_crtc_disable, - .commit = mdp5_crtc_enable, + .disable = mdp5_crtc_disable, + .enable = mdp5_crtc_enable, .atomic_check = mdp5_crtc_atomic_check, .atomic_begin = mdp5_crtc_atomic_begin, .atomic_flush = mdp5_crtc_atomic_flush, diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c index d6a14bb99988..af0e02fa4f48 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c @@ -267,14 +267,14 @@ static void mdp5_encoder_enable(struct drm_encoder *encoder) mdp5_write(mdp5_kms, REG_MDP5_INTF_TIMING_ENGINE_EN(intf), 1); spin_unlock_irqrestore(&mdp5_encoder->intf_lock, flags); - mdp5_encoder->enabled = false; + mdp5_encoder->enabled = true; } static const struct drm_encoder_helper_funcs mdp5_encoder_helper_funcs = { .mode_fixup = mdp5_encoder_mode_fixup, .mode_set = mdp5_encoder_mode_set, - .prepare = mdp5_encoder_disable, - .commit = mdp5_encoder_enable, + .disable = mdp5_encoder_disable, + .enable = mdp5_encoder_enable, }; /* initialize encoder */ -- cgit v1.2.3-59-g8ed1b From 8a4247d645a3b864e3359a5b60d41dc74a7a7b2a Mon Sep 17 00:00:00 2001 From: Stephane Viau Date: Fri, 20 Feb 2015 16:30:55 -0500 Subject: drm/msm: update generated headers (add 6th lm.base entry) Some target have up to 6 layer mixers (LM). Let the header file access the last LM's base address. Signed-off-by: Stephane Viau Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/mdp/mdp5/mdp5.xml.h | 15 ++++----------- 1 file changed, 4 insertions(+), 11 deletions(-) diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5.xml.h b/drivers/gpu/drm/msm/mdp/mdp5/mdp5.xml.h index 09b4a25eb553..c276624290af 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5.xml.h +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5.xml.h @@ -8,17 +8,9 @@ http://github.com/freedreno/envytools/ git clone https://github.com/freedreno/envytools.git The rules-ng-ng source files this header was generated from are: -- /home/robclark/src/freedreno/envytools/rnndb/msm.xml ( 676 bytes, from 2014-12-05 15:34:49) -- /home/robclark/src/freedreno/envytools/rnndb/freedreno_copyright.xml ( 1453 bytes, from 2013-03-31 16:51:27) -- /home/robclark/src/freedreno/envytools/rnndb/mdp/mdp4.xml ( 20908 bytes, from 2014-12-08 16:13:00) -- /home/robclark/src/freedreno/envytools/rnndb/mdp/mdp_common.xml ( 2357 bytes, from 2014-12-08 16:13:00) -- /home/robclark/src/freedreno/envytools/rnndb/mdp/mdp5.xml ( 27208 bytes, from 2015-01-13 23:56:11) -- /home/robclark/src/freedreno/envytools/rnndb/dsi/dsi.xml ( 11712 bytes, from 2013-08-17 17:13:43) -- /home/robclark/src/freedreno/envytools/rnndb/dsi/sfpb.xml ( 344 bytes, from 2013-08-11 19:26:32) -- /home/robclark/src/freedreno/envytools/rnndb/dsi/mmss_cc.xml ( 1686 bytes, from 2014-10-31 16:48:57) -- /home/robclark/src/freedreno/envytools/rnndb/hdmi/qfprom.xml ( 600 bytes, from 2013-07-05 19:21:12) -- /home/robclark/src/freedreno/envytools/rnndb/hdmi/hdmi.xml ( 26848 bytes, from 2015-01-13 23:55:57) -- /home/robclark/src/freedreno/envytools/rnndb/edp/edp.xml ( 8253 bytes, from 2014-12-08 16:13:00) +- /local/mnt2/workspace2/sviau/envytools/rnndb/mdp/mdp5.xml ( 27229 bytes, from 2015-02-10 17:00:41) +- /local/mnt2/workspace2/sviau/envytools/rnndb/freedreno_copyright.xml ( 1453 bytes, from 2014-06-02 18:31:15) +- /local/mnt2/workspace2/sviau/envytools/rnndb/mdp/mdp_common.xml ( 2357 bytes, from 2015-01-23 16:20:19) Copyright (C) 2013-2015 by the following authors: - Rob Clark (robclark) @@ -910,6 +902,7 @@ static inline uint32_t __offset_LM(uint32_t idx) case 2: return (mdp5_cfg->lm.base[2]); case 3: return (mdp5_cfg->lm.base[3]); case 4: return (mdp5_cfg->lm.base[4]); + case 5: return (mdp5_cfg->lm.base[5]); default: return INVALID_IDX(idx); } } -- cgit v1.2.3-59-g8ed1b From ba0312a6108f5214efb4659c4dbba218c5b9eb8d Mon Sep 17 00:00:00 2001 From: Stephane Viau Date: Fri, 20 Feb 2015 16:30:56 -0500 Subject: drm/msm/mdp5: Avoid flushing registers when CRTC is disabled When a CRTC is disabled, no CTL is allocated to it (CRTC->ctl == NULL); in that case we should not try to FLUSH registers and do nothing instead. This can happen when we try to move a cursor but the CRTC's CTL (CONTROL) has not been allocated yet (inactive CRTC). It can also happens when we .atomic_check()/.atomic_flush() on a disabled CRTC. A CTL needs to be kept as long as the CRTC is alive. Releasing it after the last VBlank is safer than in .atomic_flush(). Signed-off-by: Stephane Viau Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c | 26 +++++++++++++++++++------- 1 file changed, 19 insertions(+), 7 deletions(-) diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c index 946b71b6e608..2aeae7351621 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c @@ -103,8 +103,8 @@ static void crtc_flush_all(struct drm_crtc *crtc) struct drm_plane *plane; uint32_t flush_mask = 0; - /* we could have already released CTL in the disable path: */ - if (!mdp5_crtc->ctl) + /* this should not happen: */ + if (WARN_ON(!mdp5_crtc->ctl)) return; drm_atomic_crtc_for_each_plane(plane, crtc) { @@ -143,6 +143,11 @@ static void complete_flip(struct drm_crtc *crtc, struct drm_file *file) drm_atomic_crtc_for_each_plane(plane, crtc) { mdp5_plane_complete_flip(plane); } + + if (mdp5_crtc->ctl && !crtc->state->enable) { + mdp5_ctl_release(mdp5_crtc->ctl); + mdp5_crtc->ctl = NULL; + } } static void unref_cursor_worker(struct drm_flip_work *work, void *val) @@ -386,14 +391,17 @@ static void mdp5_crtc_atomic_flush(struct drm_crtc *crtc) mdp5_crtc->event = crtc->state->event; spin_unlock_irqrestore(&dev->event_lock, flags); + /* + * If no CTL has been allocated in mdp5_crtc_atomic_check(), + * it means we are trying to flush a CRTC whose state is disabled: + * nothing else needs to be done. + */ + if (unlikely(!mdp5_crtc->ctl)) + return; + blend_setup(crtc); crtc_flush_all(crtc); request_pending(crtc, PENDING_FLIP); - - if (mdp5_crtc->ctl && !crtc->state->enable) { - mdp5_ctl_release(mdp5_crtc->ctl); - mdp5_crtc->ctl = NULL; - } } static int mdp5_crtc_set_property(struct drm_crtc *crtc, @@ -495,6 +503,10 @@ static int mdp5_crtc_cursor_move(struct drm_crtc *crtc, int x, int y) uint32_t roi_h; unsigned long flags; + /* In case the CRTC is disabled, just drop the cursor update */ + if (unlikely(!crtc->state->enable)) + return 0; + x = (x > 0) ? x : 0; y = (y > 0) ? y : 0; -- cgit v1.2.3-59-g8ed1b From 5b2e2b6c5e542f7334dcaeb5b577d8328a5f2fc0 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Mon, 23 Feb 2015 00:58:03 +0200 Subject: drm/msm/atomic: Don't leak atomic commit object when commit fails If the atomic commit fails due to completion wait interruption the atomic commit object is not freed and is thus leaked. Free it. Signed-off-by: Laurent Pinchart Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/msm_atomic.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/msm/msm_atomic.c b/drivers/gpu/drm/msm/msm_atomic.c index 871aa2108dc6..18fd643b6e69 100644 --- a/drivers/gpu/drm/msm/msm_atomic.c +++ b/drivers/gpu/drm/msm/msm_atomic.c @@ -219,8 +219,10 @@ int msm_atomic_commit(struct drm_device *dev, * mark our set of crtc's as busy: */ ret = start_atomic(dev->dev_private, c->crtc_mask); - if (ret) + if (ret) { + kfree(c); return ret; + } /* * This is the point of no return - everything below never fails except -- cgit v1.2.3-59-g8ed1b From 58560890b3e33d789c4f13a10324af9c85c52308 Mon Sep 17 00:00:00 2001 From: Rob Clark Date: Tue, 24 Feb 2015 14:47:57 -0500 Subject: drm/msm/mdp5: fix cursor ROI If cursor is set near the edge of the screen, it is not valid to use the new cursor width/height as the ROI dimensions. Split out the ROI calc and use it both cursor_set and cursor_move. Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c | 68 +++++++++++++++++++------------- 1 file changed, 40 insertions(+), 28 deletions(-) diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c index 2aeae7351621..4c4be4344653 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c @@ -62,8 +62,8 @@ struct mdp5_crtc { /* current cursor being scanned out: */ struct drm_gem_object *scanout_bo; - uint32_t width; - uint32_t height; + uint32_t width, height; + uint32_t x, y; } cursor; }; #define to_mdp5_crtc(x) container_of(x, struct mdp5_crtc, base) @@ -411,6 +411,32 @@ static int mdp5_crtc_set_property(struct drm_crtc *crtc, return -EINVAL; } +static void get_roi(struct drm_crtc *crtc, uint32_t *roi_w, uint32_t *roi_h) +{ + struct mdp5_crtc *mdp5_crtc = to_mdp5_crtc(crtc); + uint32_t xres = crtc->mode.hdisplay; + uint32_t yres = crtc->mode.vdisplay; + + /* + * Cursor Region Of Interest (ROI) is a plane read from cursor + * buffer to render. The ROI region is determined by the visibility of + * the cursor point. In the default Cursor image the cursor point will + * be at the top left of the cursor image, unless it is specified + * otherwise using hotspot feature. + * + * If the cursor point reaches the right (xres - x < cursor.width) or + * bottom (yres - y < cursor.height) boundary of the screen, then ROI + * width and ROI height need to be evaluated to crop the cursor image + * accordingly. + * (xres-x) will be new cursor width when x > (xres - cursor.width) + * (yres-y) will be new cursor height when y > (yres - cursor.height) + */ + *roi_w = min(mdp5_crtc->cursor.width, xres - + mdp5_crtc->cursor.x); + *roi_h = min(mdp5_crtc->cursor.height, yres - + mdp5_crtc->cursor.y); +} + static int mdp5_crtc_cursor_set(struct drm_crtc *crtc, struct drm_file *file, uint32_t handle, uint32_t width, uint32_t height) @@ -424,6 +450,7 @@ static int mdp5_crtc_cursor_set(struct drm_crtc *crtc, unsigned int depth; enum mdp5_cursor_alpha cur_alpha = CURSOR_ALPHA_PER_PIXEL; uint32_t flush_mask = mdp_ctl_flush_mask_cursor(0); + uint32_t roi_w, roi_h; unsigned long flags; if ((width > CURSOR_WIDTH) || (height > CURSOR_HEIGHT)) { @@ -454,6 +481,12 @@ static int mdp5_crtc_cursor_set(struct drm_crtc *crtc, spin_lock_irqsave(&mdp5_crtc->cursor.lock, flags); old_bo = mdp5_crtc->cursor.scanout_bo; + mdp5_crtc->cursor.scanout_bo = cursor_bo; + mdp5_crtc->cursor.width = width; + mdp5_crtc->cursor.height = height; + + get_roi(crtc, &roi_w, &roi_h); + mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_STRIDE(lm), stride); mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_FORMAT(lm), MDP5_LM_CURSOR_FORMAT_FORMAT(CURSOR_FMT_ARGB8888)); @@ -461,19 +494,15 @@ static int mdp5_crtc_cursor_set(struct drm_crtc *crtc, MDP5_LM_CURSOR_IMG_SIZE_SRC_H(height) | MDP5_LM_CURSOR_IMG_SIZE_SRC_W(width)); mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_SIZE(lm), - MDP5_LM_CURSOR_SIZE_ROI_H(height) | - MDP5_LM_CURSOR_SIZE_ROI_W(width)); + MDP5_LM_CURSOR_SIZE_ROI_H(roi_h) | + MDP5_LM_CURSOR_SIZE_ROI_W(roi_w)); mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_BASE_ADDR(lm), cursor_addr); - blendcfg = MDP5_LM_CURSOR_BLEND_CONFIG_BLEND_EN; blendcfg |= MDP5_LM_CURSOR_BLEND_CONFIG_BLEND_TRANSP_EN; blendcfg |= MDP5_LM_CURSOR_BLEND_CONFIG_BLEND_ALPHA_SEL(cur_alpha); mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_BLEND_CONFIG(lm), blendcfg); - mdp5_crtc->cursor.scanout_bo = cursor_bo; - mdp5_crtc->cursor.width = width; - mdp5_crtc->cursor.height = height; spin_unlock_irqrestore(&mdp5_crtc->cursor.lock, flags); ret = mdp5_ctl_set_cursor(mdp5_crtc->ctl, true); @@ -497,8 +526,6 @@ static int mdp5_crtc_cursor_move(struct drm_crtc *crtc, int x, int y) struct mdp5_kms *mdp5_kms = get_kms(crtc); struct mdp5_crtc *mdp5_crtc = to_mdp5_crtc(crtc); uint32_t flush_mask = mdp_ctl_flush_mask_cursor(0); - uint32_t xres = crtc->mode.hdisplay; - uint32_t yres = crtc->mode.vdisplay; uint32_t roi_w; uint32_t roi_h; unsigned long flags; @@ -507,25 +534,10 @@ static int mdp5_crtc_cursor_move(struct drm_crtc *crtc, int x, int y) if (unlikely(!crtc->state->enable)) return 0; - x = (x > 0) ? x : 0; - y = (y > 0) ? y : 0; + mdp5_crtc->cursor.x = x = max(x, 0); + mdp5_crtc->cursor.y = y = max(y, 0); - /* - * Cursor Region Of Interest (ROI) is a plane read from cursor - * buffer to render. The ROI region is determined by the visiblity of - * the cursor point. In the default Cursor image the cursor point will - * be at the top left of the cursor image, unless it is specified - * otherwise using hotspot feature. - * - * If the cursor point reaches the right (xres - x < cursor.width) or - * bottom (yres - y < cursor.height) boundary of the screen, then ROI - * width and ROI height need to be evaluated to crop the cursor image - * accordingly. - * (xres-x) will be new cursor width when x > (xres - cursor.width) - * (yres-y) will be new cursor height when y > (yres - cursor.height) - */ - roi_w = min(mdp5_crtc->cursor.width, xres - x); - roi_h = min(mdp5_crtc->cursor.height, yres - y); + get_roi(crtc, &roi_w, &roi_h); spin_lock_irqsave(&mdp5_crtc->cursor.lock, flags); mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_SIZE(mdp5_crtc->lm), -- cgit v1.2.3-59-g8ed1b From 757fdfaf413c4a85dade5374b6f5c05d541cf32e Mon Sep 17 00:00:00 2001 From: Rob Clark Date: Tue, 24 Feb 2015 15:29:37 -0500 Subject: drm/msm/mdp5: fix cursor blending Seems like we just want BLEND_EN and not BLEND_TRANSP_EN (setting the latter results in black pixels in the cursor image treated as transparent). Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c index 4c4be4344653..2f2863cf8b45 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c @@ -499,7 +499,6 @@ static int mdp5_crtc_cursor_set(struct drm_crtc *crtc, mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_BASE_ADDR(lm), cursor_addr); blendcfg = MDP5_LM_CURSOR_BLEND_CONFIG_BLEND_EN; - blendcfg |= MDP5_LM_CURSOR_BLEND_CONFIG_BLEND_TRANSP_EN; blendcfg |= MDP5_LM_CURSOR_BLEND_CONFIG_BLEND_ALPHA_SEL(cur_alpha); mdp5_write(mdp5_kms, REG_MDP5_LM_CURSOR_BLEND_CONFIG(lm), blendcfg); -- cgit v1.2.3-59-g8ed1b From aa80a4a5190e697a6945849ab36fa7dabca815f3 Mon Sep 17 00:00:00 2001 From: Rob Clark Date: Mon, 2 Mar 2015 16:19:06 -0500 Subject: drm/msm: kexec fixes In kexec environment, we are more likely to encounter irq's already enabled from previous environment. At which point we find that writes to disable/clear pending irq's are slightly less than useless without first enabling clocks. TODO: full blown state read-in so kexec'd kernel can inherit the mode already setup. Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/mdp/mdp4/mdp4_irq.c | 5 +++++ drivers/gpu/drm/msm/mdp/mdp5/mdp5_irq.c | 5 +++++ 2 files changed, 10 insertions(+) diff --git a/drivers/gpu/drm/msm/mdp/mdp4/mdp4_irq.c b/drivers/gpu/drm/msm/mdp/mdp4/mdp4_irq.c index 8edd531cb621..7369ee7f0c55 100644 --- a/drivers/gpu/drm/msm/mdp/mdp4/mdp4_irq.c +++ b/drivers/gpu/drm/msm/mdp/mdp4/mdp4_irq.c @@ -32,7 +32,10 @@ static void mdp4_irq_error_handler(struct mdp_irq *irq, uint32_t irqstatus) void mdp4_irq_preinstall(struct msm_kms *kms) { struct mdp4_kms *mdp4_kms = to_mdp4_kms(to_mdp_kms(kms)); + mdp4_enable(mdp4_kms); mdp4_write(mdp4_kms, REG_MDP4_INTR_CLEAR, 0xffffffff); + mdp4_write(mdp4_kms, REG_MDP4_INTR_ENABLE, 0x00000000); + mdp4_disable(mdp4_kms); } int mdp4_irq_postinstall(struct msm_kms *kms) @@ -53,7 +56,9 @@ int mdp4_irq_postinstall(struct msm_kms *kms) void mdp4_irq_uninstall(struct msm_kms *kms) { struct mdp4_kms *mdp4_kms = to_mdp4_kms(to_mdp_kms(kms)); + mdp4_enable(mdp4_kms); mdp4_write(mdp4_kms, REG_MDP4_INTR_ENABLE, 0x00000000); + mdp4_disable(mdp4_kms); } irqreturn_t mdp4_irq(struct msm_kms *kms) diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_irq.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_irq.c index 70ac81edd40f..a9407105b9b7 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_irq.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_irq.c @@ -34,7 +34,10 @@ static void mdp5_irq_error_handler(struct mdp_irq *irq, uint32_t irqstatus) void mdp5_irq_preinstall(struct msm_kms *kms) { struct mdp5_kms *mdp5_kms = to_mdp5_kms(to_mdp_kms(kms)); + mdp5_enable(mdp5_kms); mdp5_write(mdp5_kms, REG_MDP5_INTR_CLEAR, 0xffffffff); + mdp5_write(mdp5_kms, REG_MDP5_INTR_EN, 0x00000000); + mdp5_disable(mdp5_kms); } int mdp5_irq_postinstall(struct msm_kms *kms) @@ -57,7 +60,9 @@ int mdp5_irq_postinstall(struct msm_kms *kms) void mdp5_irq_uninstall(struct msm_kms *kms) { struct mdp5_kms *mdp5_kms = to_mdp5_kms(to_mdp_kms(kms)); + mdp5_enable(mdp5_kms); mdp5_write(mdp5_kms, REG_MDP5_INTR_EN, 0x00000000); + mdp5_disable(mdp5_kms); } static void mdp5_irq_mdp(struct mdp_kms *mdp_kms) -- cgit v1.2.3-59-g8ed1b From 956421fbb74c3a6261903f3836c0740187cf038b Mon Sep 17 00:00:00 2001 From: Andy Lutomirski Date: Thu, 5 Mar 2015 01:09:44 +0100 Subject: x86/asm/entry/64: Remove a bogus 'ret_from_fork' optimization 'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and the related state make sense for 'ret_from_sys_call'. This is entirely the wrong check. TS_COMPAT would make a little more sense, but there's really no point in keeping this optimization at all. This fixes a return to the wrong user CS if we came from int 0x80 in a 64-bit task. Signed-off-by: Andy Lutomirski Cc: Borislav Petkov Cc: Denys Vlasenko Cc: H. Peter Anvin Cc: Linus Torvalds Cc: Oleg Nesterov Cc: Thomas Gleixner Cc: Link: http://lkml.kernel.org/r/4710be56d76ef994ddf59087aad98c000fbab9a4.1424989793.git.luto@amacapital.net [ Backported from tip:x86/asm. ] Signed-off-by: Ingo Molnar --- arch/x86/kernel/entry_64.S | 13 ++++++++----- 1 file changed, 8 insertions(+), 5 deletions(-) diff --git a/arch/x86/kernel/entry_64.S b/arch/x86/kernel/entry_64.S index 10074ad9ebf8..1d74d161687c 100644 --- a/arch/x86/kernel/entry_64.S +++ b/arch/x86/kernel/entry_64.S @@ -269,11 +269,14 @@ ENTRY(ret_from_fork) testl $3, CS-ARGOFFSET(%rsp) # from kernel_thread? jz 1f - testl $_TIF_IA32, TI_flags(%rcx) # 32-bit compat task needs IRET - jnz int_ret_from_sys_call - - RESTORE_TOP_OF_STACK %rdi, -ARGOFFSET - jmp ret_from_sys_call # go to the SYSRET fastpath + /* + * By the time we get here, we have no idea whether our pt_regs, + * ti flags, and ti status came from the 64-bit SYSCALL fast path, + * the slow path, or one of the ia32entry paths. + * Use int_ret_from_sys_call to return, since it can safely handle + * all of the above. + */ + jmp int_ret_from_sys_call 1: subq $REST_SKIP, %rsp # leave space for volatiles -- cgit v1.2.3-59-g8ed1b From d5bce867778c8cb5ff655efe47fecb4b31f30406 Mon Sep 17 00:00:00 2001 From: Srinivas Pandruvada Date: Mon, 2 Mar 2015 13:12:07 -0800 Subject: Thermal/int340x: Fix memleak for aux trip When thermal zone device register fails or on module exit, the memory for aux_trip is not freed. This change fixes this issue. Signed-off-by: Srinivas Pandruvada Signed-off-by: Eduardo Valentin --- drivers/thermal/int340x_thermal/int340x_thermal_zone.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/thermal/int340x_thermal/int340x_thermal_zone.c b/drivers/thermal/int340x_thermal/int340x_thermal_zone.c index f88b08877025..1e25133d35e2 100644 --- a/drivers/thermal/int340x_thermal/int340x_thermal_zone.c +++ b/drivers/thermal/int340x_thermal/int340x_thermal_zone.c @@ -208,7 +208,7 @@ struct int34x_thermal_zone *int340x_thermal_zone_add(struct acpi_device *adev, trip_cnt, GFP_KERNEL); if (!int34x_thermal_zone->aux_trips) { ret = -ENOMEM; - goto free_mem; + goto err_trip_alloc; } trip_mask = BIT(trip_cnt) - 1; int34x_thermal_zone->aux_trip_nr = trip_cnt; @@ -248,14 +248,15 @@ struct int34x_thermal_zone *int340x_thermal_zone_add(struct acpi_device *adev, 0, 0); if (IS_ERR(int34x_thermal_zone->zone)) { ret = PTR_ERR(int34x_thermal_zone->zone); - goto free_lpat; + goto err_thermal_zone; } return int34x_thermal_zone; -free_lpat: +err_thermal_zone: acpi_lpat_free_conversion_table(int34x_thermal_zone->lpat_table); -free_mem: + kfree(int34x_thermal_zone->aux_trips); +err_trip_alloc: kfree(int34x_thermal_zone); return ERR_PTR(ret); } @@ -266,6 +267,7 @@ void int340x_thermal_zone_remove(struct int34x_thermal_zone { thermal_zone_device_unregister(int34x_thermal_zone->zone); acpi_lpat_free_conversion_table(int34x_thermal_zone->lpat_table); + kfree(int34x_thermal_zone->aux_trips); kfree(int34x_thermal_zone); } EXPORT_SYMBOL_GPL(int340x_thermal_zone_remove); -- cgit v1.2.3-59-g8ed1b From 2dc10f8963e6a03a1a75deafe1d1984bafab08dd Mon Sep 17 00:00:00 2001 From: Matthias Kaehlcke Date: Fri, 20 Feb 2015 18:10:08 -0800 Subject: thermal: Make sysfs attributes of cooling devices default attributes Default attributes are created when the device is registered. Attributes created after device registration can lead to race conditions, where user space (e.g. udev) sees the device but not the attributes. Signed-off-by: Matthias Kaehlcke Signed-off-by: Eduardo Valentin --- drivers/thermal/thermal_core.c | 37 +++++++++++++++++-------------------- 1 file changed, 17 insertions(+), 20 deletions(-) diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c index 48491d1a81d6..174d3bcf8bd7 100644 --- a/drivers/thermal/thermal_core.c +++ b/drivers/thermal/thermal_core.c @@ -899,6 +899,22 @@ thermal_cooling_device_trip_point_show(struct device *dev, return sprintf(buf, "%d\n", instance->trip); } +static struct attribute *cooling_device_attrs[] = { + &dev_attr_cdev_type.attr, + &dev_attr_max_state.attr, + &dev_attr_cur_state.attr, + NULL, +}; + +static const struct attribute_group cooling_device_attr_group = { + .attrs = cooling_device_attrs, +}; + +static const struct attribute_group *cooling_device_attr_groups[] = { + &cooling_device_attr_group, + NULL, +}; + /* Device management */ /** @@ -1130,6 +1146,7 @@ __thermal_cooling_device_register(struct device_node *np, cdev->ops = ops; cdev->updated = false; cdev->device.class = &thermal_class; + cdev->device.groups = cooling_device_attr_groups; cdev->devdata = devdata; dev_set_name(&cdev->device, "cooling_device%d", cdev->id); result = device_register(&cdev->device); @@ -1139,21 +1156,6 @@ __thermal_cooling_device_register(struct device_node *np, return ERR_PTR(result); } - /* sys I/F */ - if (type) { - result = device_create_file(&cdev->device, &dev_attr_cdev_type); - if (result) - goto unregister; - } - - result = device_create_file(&cdev->device, &dev_attr_max_state); - if (result) - goto unregister; - - result = device_create_file(&cdev->device, &dev_attr_cur_state); - if (result) - goto unregister; - /* Add 'this' new cdev to the global cdev list */ mutex_lock(&thermal_list_lock); list_add(&cdev->node, &thermal_cdev_list); @@ -1163,11 +1165,6 @@ __thermal_cooling_device_register(struct device_node *np, bind_cdev(cdev); return cdev; - -unregister: - release_idr(&thermal_cdev_idr, &thermal_idr_lock, cdev->id); - device_unregister(&cdev->device); - return ERR_PTR(result); } /** -- cgit v1.2.3-59-g8ed1b From 94b3eed7b8a4311f56a86b36430e9068b596ada4 Mon Sep 17 00:00:00 2001 From: Jie Yang Date: Thu, 5 Mar 2015 14:08:08 +0800 Subject: dmaengine: dw: don't handle interrupt when dmaengine is not used When dma controller is not used by any user and set off, we should disble interrupt handler, at least the interrupt reset part, for some subsystem, e.g. ADSP, may use the dma in its own logic, here reset the interrupt may make this subsystem work abnormally. Signed-off-by: Jie Yang Signed-off-by: Vinod Koul --- drivers/dma/dw/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/dma/dw/core.c b/drivers/dma/dw/core.c index 455b7a4f1e87..a8ad05291b27 100644 --- a/drivers/dma/dw/core.c +++ b/drivers/dma/dw/core.c @@ -626,7 +626,7 @@ static irqreturn_t dw_dma_interrupt(int irq, void *dev_id) dev_vdbg(dw->dma.dev, "%s: status=0x%x\n", __func__, status); /* Check if we have any interrupt from the DMAC */ - if (!status) + if (!status || !dw->in_use) return IRQ_NONE; /* -- cgit v1.2.3-59-g8ed1b From 6eb9d3c1e9c5977f7fe6be125006443e7da2427c Mon Sep 17 00:00:00 2001 From: Ludovic Desroches Date: Thu, 12 Feb 2015 16:30:30 +0100 Subject: dmaengine: at_xdmac: fix for chan conf simplification When simplificating the channel configuration, the cyclic case has been forgotten. It leads to use bad configuration causing many bugs. Signed-off-by: Ludovic Desroches Acked-by: Nicolas Ferre Signed-off-by: Vinod Koul --- drivers/dma/at_xdmac.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/drivers/dma/at_xdmac.c b/drivers/dma/at_xdmac.c index 09e2825a547a..d9891d3461f6 100644 --- a/drivers/dma/at_xdmac.c +++ b/drivers/dma/at_xdmac.c @@ -664,7 +664,6 @@ at_xdmac_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t buf_addr, struct at_xdmac_desc *first = NULL, *prev = NULL; unsigned int periods = buf_len / period_len; int i; - u32 cfg; dev_dbg(chan2dev(chan), "%s: buf_addr=%pad, buf_len=%zd, period_len=%zd, dir=%s, flags=0x%lx\n", __func__, &buf_addr, buf_len, period_len, @@ -700,17 +699,17 @@ at_xdmac_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t buf_addr, if (direction == DMA_DEV_TO_MEM) { desc->lld.mbr_sa = atchan->per_src_addr; desc->lld.mbr_da = buf_addr + i * period_len; - cfg = atchan->cfg[AT_XDMAC_DEV_TO_MEM_CFG]; + desc->lld.mbr_cfg = atchan->cfg[AT_XDMAC_DEV_TO_MEM_CFG]; } else { desc->lld.mbr_sa = buf_addr + i * period_len; desc->lld.mbr_da = atchan->per_dst_addr; - cfg = atchan->cfg[AT_XDMAC_MEM_TO_DEV_CFG]; + desc->lld.mbr_cfg = atchan->cfg[AT_XDMAC_MEM_TO_DEV_CFG]; } desc->lld.mbr_ubc = AT_XDMAC_MBR_UBC_NDV1 | AT_XDMAC_MBR_UBC_NDEN | AT_XDMAC_MBR_UBC_NSEN | AT_XDMAC_MBR_UBC_NDE - | period_len >> at_xdmac_get_dwidth(cfg); + | period_len >> at_xdmac_get_dwidth(desc->lld.mbr_cfg); dev_dbg(chan2dev(chan), "%s: lld: mbr_sa=%pad, mbr_da=%pad, mbr_ubc=0x%08x\n", -- cgit v1.2.3-59-g8ed1b From 9ca1c5f2ab9d5bc8955a2cc7ad36ba7074dd7c60 Mon Sep 17 00:00:00 2001 From: Dave Jiang Date: Fri, 13 Feb 2015 12:23:53 -0700 Subject: dmaengine: ioatdma: workaround for incorrect DMACAP register BDX-DE IOATDMA reports incorrect DMACAP register for PQ related ops. Ignoring those bits. Signed-off-by: Dave Jiang Acked-by: Dan Williams Signed-off-by: Vinod Koul --- drivers/dma/ioat/dma_v3.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/dma/ioat/dma_v3.c b/drivers/dma/ioat/dma_v3.c index 77a6dcf25b98..194ec20c9408 100644 --- a/drivers/dma/ioat/dma_v3.c +++ b/drivers/dma/ioat/dma_v3.c @@ -230,6 +230,10 @@ static bool is_bwd_noraid(struct pci_dev *pdev) switch (pdev->device) { case PCI_DEVICE_ID_INTEL_IOAT_BWD2: case PCI_DEVICE_ID_INTEL_IOAT_BWD3: + case PCI_DEVICE_ID_INTEL_IOAT_BDXDE0: + case PCI_DEVICE_ID_INTEL_IOAT_BDXDE1: + case PCI_DEVICE_ID_INTEL_IOAT_BDXDE2: + case PCI_DEVICE_ID_INTEL_IOAT_BDXDE3: return true; default: return false; -- cgit v1.2.3-59-g8ed1b From 096a020a9ef5c947577d3b57199bfc9b7e686b49 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Thu, 5 Mar 2015 14:26:37 +0300 Subject: ALSA: msnd: add some missing curly braces There were some curly braces intended here. Signed-off-by: Dan Carpenter Signed-off-by: Takashi Iwai --- sound/isa/msnd/msnd_pinnacle_mixer.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/sound/isa/msnd/msnd_pinnacle_mixer.c b/sound/isa/msnd/msnd_pinnacle_mixer.c index 17e49a071af4..b408540798c1 100644 --- a/sound/isa/msnd/msnd_pinnacle_mixer.c +++ b/sound/isa/msnd/msnd_pinnacle_mixer.c @@ -306,11 +306,12 @@ int snd_msndmix_new(struct snd_card *card) spin_lock_init(&chip->mixer_lock); strcpy(card->mixername, "MSND Pinnacle Mixer"); - for (idx = 0; idx < ARRAY_SIZE(snd_msnd_controls); idx++) + for (idx = 0; idx < ARRAY_SIZE(snd_msnd_controls); idx++) { err = snd_ctl_add(card, snd_ctl_new1(snd_msnd_controls + idx, chip)); if (err < 0) return err; + } return 0; } -- cgit v1.2.3-59-g8ed1b From f44f07cf3910f84b15b2a78c4933d5946bf409cf Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 5 Mar 2015 13:03:28 +0100 Subject: ALSA: line6: Clamp values correctly The usages of clamp() macro in sound/usb/line6/playback.c are just wrong, the low and high values are swapped. Reported-by: Dan Carpenter Signed-off-by: Takashi Iwai --- sound/usb/line6/playback.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/sound/usb/line6/playback.c b/sound/usb/line6/playback.c index 05dee690f487..97ed593f6010 100644 --- a/sound/usb/line6/playback.c +++ b/sound/usb/line6/playback.c @@ -39,7 +39,7 @@ static void change_volume(struct urb *urb_out, int volume[], for (; p < buf_end; ++p) { short pv = le16_to_cpu(*p); int val = (pv * volume[chn & 1]) >> 8; - pv = clamp(val, 0x7fff, -0x8000); + pv = clamp(val, -0x8000, 0x7fff); *p = cpu_to_le16(pv); ++chn; } @@ -54,7 +54,7 @@ static void change_volume(struct urb *urb_out, int volume[], val = p[0] + (p[1] << 8) + ((signed char)p[2] << 16); val = (val * volume[chn & 1]) >> 8; - val = clamp(val, 0x7fffff, -0x800000); + val = clamp(val, -0x800000, 0x7fffff); p[0] = val; p[1] = val >> 8; p[2] = val >> 16; @@ -126,7 +126,7 @@ static void add_monitor_signal(struct urb *urb_out, unsigned char *signal, short pov = le16_to_cpu(*po); short piv = le16_to_cpu(*pi); int val = pov + ((piv * volume) >> 8); - pov = clamp(val, 0x7fff, -0x8000); + pov = clamp(val, -0x8000, 0x7fff); *po = cpu_to_le16(pov); } } -- cgit v1.2.3-59-g8ed1b From fe4be5e9f99d433fe6420a12f4e94f05f2ae39a6 Mon Sep 17 00:00:00 2001 From: Stanimir Varbanov Date: Thu, 5 Mar 2015 15:03:04 +0200 Subject: dmaengine: bam-dma: fix a warning about missing capabilities Avoid the warning below triggered during dmaengine async device registration. WARNING: CPU: 1 PID: 1 at linux/drivers/dma/dmaengine.c:863 dma_async_device_register+0x2a8/0x4b8() this driver doesn't support generic slave capabilities reporting To do that fill mandatory .directions bit mask, .src/dst_addr_widths and .residue_granularity dma_device fields with appropriate values. Signed-off-by: Stanimir Varbanov Signed-off-by: Vinod Koul --- drivers/dma/qcom_bam_dma.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/dma/qcom_bam_dma.c b/drivers/dma/qcom_bam_dma.c index d7a33b3ac466..d9f1a18b9295 100644 --- a/drivers/dma/qcom_bam_dma.c +++ b/drivers/dma/qcom_bam_dma.c @@ -1143,6 +1143,10 @@ static int bam_dma_probe(struct platform_device *pdev) dma_cap_set(DMA_SLAVE, bdev->common.cap_mask); /* initialize dmaengine apis */ + bdev->common.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV); + bdev->common.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT; + bdev->common.src_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES; + bdev->common.dst_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES; bdev->common.device_alloc_chan_resources = bam_alloc_chan; bdev->common.device_free_chan_resources = bam_free_chan; bdev->common.device_prep_slave_sg = bam_prep_slave_sg; -- cgit v1.2.3-59-g8ed1b From 90b1047f138459e86861cf401c5e9f0a9aa3b23b Mon Sep 17 00:00:00 2001 From: Stanimir Varbanov Date: Thu, 19 Feb 2015 18:45:50 +0200 Subject: dmaengine: qcom_bam_dma: fix wrong register offsets The commit fb93f520e (dmaengine: qcom_bam_dma: Generalize BAM register offset calculations) wrongly populated base offsets for event registers for bam v1.4. Signed-off-by: Stanimir Varbanov Reviewed-by: Archit Taneja Reviewed-by: Andy Gross Signed-off-by: Vinod Koul --- drivers/dma/qcom_bam_dma.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/dma/qcom_bam_dma.c b/drivers/dma/qcom_bam_dma.c index d9f1a18b9295..9c914d625906 100644 --- a/drivers/dma/qcom_bam_dma.c +++ b/drivers/dma/qcom_bam_dma.c @@ -162,9 +162,9 @@ static const struct reg_offset_data bam_v1_4_reg_info[] = { [BAM_P_IRQ_STTS] = { 0x1010, 0x1000, 0x00, 0x00 }, [BAM_P_IRQ_CLR] = { 0x1014, 0x1000, 0x00, 0x00 }, [BAM_P_IRQ_EN] = { 0x1018, 0x1000, 0x00, 0x00 }, - [BAM_P_EVNT_DEST_ADDR] = { 0x102C, 0x00, 0x1000, 0x00 }, - [BAM_P_EVNT_REG] = { 0x1018, 0x00, 0x1000, 0x00 }, - [BAM_P_SW_OFSTS] = { 0x1000, 0x00, 0x1000, 0x00 }, + [BAM_P_EVNT_DEST_ADDR] = { 0x182C, 0x00, 0x1000, 0x00 }, + [BAM_P_EVNT_REG] = { 0x1818, 0x00, 0x1000, 0x00 }, + [BAM_P_SW_OFSTS] = { 0x1800, 0x00, 0x1000, 0x00 }, [BAM_P_DATA_FIFO_ADDR] = { 0x1824, 0x00, 0x1000, 0x00 }, [BAM_P_DESC_FIFO_ADDR] = { 0x181C, 0x00, 0x1000, 0x00 }, [BAM_P_EVNT_GEN_TRSHLD] = { 0x1828, 0x00, 0x1000, 0x00 }, -- cgit v1.2.3-59-g8ed1b From 9ab6eb51ef4ad63cb71533d3a4dfb09ea8f69b4c Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Thu, 5 Mar 2015 17:24:04 +0200 Subject: x86/intel/quark: Select COMMON_CLK The commit 8bbc2a135b63 ("x86/intel/quark: Add Intel Quark platform support") introduced a minimal support of Intel Quark SoC. That allows to use core parts of the SoC. However, the SPI, I2C, and GPIO drivers can't be selected by kernel configuration because they depend on COMMON_CLK. The patch adds a COMMON_CLK selection to the platfrom definition to allow user choose the drivers. Signed-off-by: Andy Shevchenko Acked-by: Ong, Boon Leong Cc: Bryan O'Donoghue Cc: Darren Hart Fixes: 8bbc2a135b63 ("x86/intel/quark: Add Intel Quark platform support") Link: http://lkml.kernel.org/r/1425569044-2867-1-git-send-email-andriy.shevchenko@linux.intel.com Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index c2fb8a87dccb..b7d31ca55187 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -499,6 +499,7 @@ config X86_INTEL_QUARK depends on X86_IO_APIC select IOSF_MBI select INTEL_IMR + select COMMON_CLK ---help--- Select to include support for Quark X1000 SoC. Say Y here if you have a Quark based system such as the Arduino -- cgit v1.2.3-59-g8ed1b From ecb9b4241f696b746215b1de36106258bc8ed957 Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Sun, 15 Feb 2015 19:49:16 +0100 Subject: dmaengine: mmp_pdma: fix warning about slave caps Fix the dmaengine complaint about missing slave caps : - declare the available bus widths - declare the available transfer types - declare the residue calculation type Signed-off-by: Robert Jarzmik Signed-off-by: Vinod Koul --- drivers/dma/mmp_pdma.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/dma/mmp_pdma.c b/drivers/dma/mmp_pdma.c index abf1450bb25d..eb410044e1af 100644 --- a/drivers/dma/mmp_pdma.c +++ b/drivers/dma/mmp_pdma.c @@ -1002,6 +1002,9 @@ static int mmp_pdma_probe(struct platform_device *op) struct resource *iores; int i, ret, irq = 0; int dma_channels = 0, irq_num = 0; + const enum dma_slave_buswidth widths = + DMA_SLAVE_BUSWIDTH_1_BYTE | DMA_SLAVE_BUSWIDTH_2_BYTES | + DMA_SLAVE_BUSWIDTH_4_BYTES; pdev = devm_kzalloc(&op->dev, sizeof(*pdev), GFP_KERNEL); if (!pdev) @@ -1069,6 +1072,10 @@ static int mmp_pdma_probe(struct platform_device *op) pdev->device.device_config = mmp_pdma_config; pdev->device.device_terminate_all = mmp_pdma_terminate_all; pdev->device.copy_align = PDMA_ALIGNMENT; + pdev->device.src_addr_widths = widths; + pdev->device.dst_addr_widths = widths; + pdev->device.directions = BIT(DMA_MEM_TO_DEV) | BIT(DMA_DEV_TO_MEM); + pdev->device.residue_granularity = DMA_RESIDUE_GRANULARITY_DESCRIPTOR; if (pdev->dev->coherent_dma_mask) dma_set_mask(pdev->dev, pdev->dev->coherent_dma_mask); -- cgit v1.2.3-59-g8ed1b From 06c8173eb92bbfc03a0fe8bb64315857d0badd06 Mon Sep 17 00:00:00 2001 From: Quentin Casasnovas Date: Thu, 5 Mar 2015 13:19:22 +0100 Subject: x86/fpu/xsaves: Fix improper uses of __ex_table Commit: f31a9f7c7169 ("x86/xsaves: Use xsaves/xrstors to save and restore xsave area") introduced alternative instructions for XSAVES/XRSTORS and commit: adb9d526e982 ("x86/xsaves: Add xsaves and xrstors support for booting time") added support for the XSAVES/XRSTORS instructions at boot time. Unfortunately both failed to properly protect them against faulting: The 'xstate_fault' macro will use the closest label named '1' backward and that ends up in the .altinstr_replacement section rather than in .text. This means that the kernel will never find in the __ex_table the .text address where this instruction might fault, leading to serious problems if userspace manages to trigger the fault. Signed-off-by: Quentin Casasnovas Signed-off-by: Jamie Iles [ Improved the changelog, fixed some whitespace noise. ] Acked-by: Borislav Petkov Acked-by: Linus Torvalds Cc: Cc: Allan Xavier Cc: H. Peter Anvin Cc: Thomas Gleixner Fixes: adb9d526e982 ("x86/xsaves: Add xsaves and xrstors support for booting time") Fixes: f31a9f7c7169 ("x86/xsaves: Use xsaves/xrstors to save and restore xsave area") Signed-off-by: Ingo Molnar --- arch/x86/include/asm/xsave.h | 28 +++++++++++----------------- 1 file changed, 11 insertions(+), 17 deletions(-) diff --git a/arch/x86/include/asm/xsave.h b/arch/x86/include/asm/xsave.h index 5fa9770035dc..c9a6d68b8d62 100644 --- a/arch/x86/include/asm/xsave.h +++ b/arch/x86/include/asm/xsave.h @@ -82,18 +82,15 @@ static inline int xsave_state_booting(struct xsave_struct *fx, u64 mask) if (boot_cpu_has(X86_FEATURE_XSAVES)) asm volatile("1:"XSAVES"\n\t" "2:\n\t" - : : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) + xstate_fault + : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) : "memory"); else asm volatile("1:"XSAVE"\n\t" "2:\n\t" - : : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) + xstate_fault + : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) : "memory"); - - asm volatile(xstate_fault - : "0" (0) - : "memory"); - return err; } @@ -112,18 +109,15 @@ static inline int xrstor_state_booting(struct xsave_struct *fx, u64 mask) if (boot_cpu_has(X86_FEATURE_XSAVES)) asm volatile("1:"XRSTORS"\n\t" "2:\n\t" - : : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) + xstate_fault + : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) : "memory"); else asm volatile("1:"XRSTOR"\n\t" "2:\n\t" - : : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) + xstate_fault + : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) : "memory"); - - asm volatile(xstate_fault - : "0" (0) - : "memory"); - return err; } @@ -149,9 +143,9 @@ static inline int xsave_state(struct xsave_struct *fx, u64 mask) */ alternative_input_2( "1:"XSAVE, - "1:"XSAVEOPT, + XSAVEOPT, X86_FEATURE_XSAVEOPT, - "1:"XSAVES, + XSAVES, X86_FEATURE_XSAVES, [fx] "D" (fx), "a" (lmask), "d" (hmask) : "memory"); @@ -178,7 +172,7 @@ static inline int xrstor_state(struct xsave_struct *fx, u64 mask) */ alternative_input( "1: " XRSTOR, - "1: " XRSTORS, + XRSTORS, X86_FEATURE_XSAVES, "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask) : "memory"); -- cgit v1.2.3-59-g8ed1b From ef2b22ac540c018bd574d1846ab95b9bfcf38702 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Mon, 2 Mar 2015 22:26:55 +0100 Subject: cpuidle / sleep: Use broadcast timer for states that stop local timer Commit 381063133246 (PM / sleep: Re-implement suspend-to-idle handling) overlooked the fact that entering some sufficiently deep idle states by CPUs may cause their local timers to stop and in those cases it is necessary to switch over to a broadcast timer prior to entering the idle state. If the cpuidle driver in use does not provide the new ->enter_freeze callback for any of the idle states, that problem affects suspend-to-idle too, but it is not taken into account after the changes made by commit 381063133246. Fix that by changing the definition of cpuidle_enter_freeze() and re-arranging of the code in cpuidle_idle_call(), so the former does not call cpuidle_enter() any more and the fallback case is handled by cpuidle_idle_call() directly. Fixes: 381063133246 (PM / sleep: Re-implement suspend-to-idle handling) Reported-and-tested-by: Lorenzo Pieralisi Signed-off-by: Rafael J. Wysocki Acked-by: Peter Zijlstra (Intel) --- drivers/cpuidle/cpuidle.c | 62 +++++++++++++++++------------------------------ include/linux/cpuidle.h | 17 +++++++++++-- kernel/sched/idle.c | 30 ++++++++++++++++------- 3 files changed, 58 insertions(+), 51 deletions(-) diff --git a/drivers/cpuidle/cpuidle.c b/drivers/cpuidle/cpuidle.c index 8b3e132b6a01..080bd2dbde4b 100644 --- a/drivers/cpuidle/cpuidle.c +++ b/drivers/cpuidle/cpuidle.c @@ -44,8 +44,8 @@ void disable_cpuidle(void) off = 1; } -static bool cpuidle_not_available(struct cpuidle_driver *drv, - struct cpuidle_device *dev) +bool cpuidle_not_available(struct cpuidle_driver *drv, + struct cpuidle_device *dev) { return off || !initialized || !drv || !dev || !dev->enabled; } @@ -72,14 +72,8 @@ int cpuidle_play_dead(void) return -ENODEV; } -/** - * cpuidle_find_deepest_state - Find deepest state meeting specific conditions. - * @drv: cpuidle driver for the given CPU. - * @dev: cpuidle device for the given CPU. - * @freeze: Whether or not the state should be suitable for suspend-to-idle. - */ -static int cpuidle_find_deepest_state(struct cpuidle_driver *drv, - struct cpuidle_device *dev, bool freeze) +static int find_deepest_state(struct cpuidle_driver *drv, + struct cpuidle_device *dev, bool freeze) { unsigned int latency_req = 0; int i, ret = freeze ? -1 : CPUIDLE_DRIVER_STATE_START - 1; @@ -98,6 +92,17 @@ static int cpuidle_find_deepest_state(struct cpuidle_driver *drv, return ret; } +/** + * cpuidle_find_deepest_state - Find the deepest available idle state. + * @drv: cpuidle driver for the given CPU. + * @dev: cpuidle device for the given CPU. + */ +int cpuidle_find_deepest_state(struct cpuidle_driver *drv, + struct cpuidle_device *dev) +{ + return find_deepest_state(drv, dev, false); +} + static void enter_freeze_proper(struct cpuidle_driver *drv, struct cpuidle_device *dev, int index) { @@ -119,46 +124,26 @@ static void enter_freeze_proper(struct cpuidle_driver *drv, /** * cpuidle_enter_freeze - Enter an idle state suitable for suspend-to-idle. + * @drv: cpuidle driver for the given CPU. + * @dev: cpuidle device for the given CPU. * * If there are states with the ->enter_freeze callback, find the deepest of - * them and enter it with frozen tick. Otherwise, find the deepest state - * available and enter it normally. - * - * Returns with enabled interrupts. + * them and enter it with frozen tick. */ -void cpuidle_enter_freeze(void) +int cpuidle_enter_freeze(struct cpuidle_driver *drv, struct cpuidle_device *dev) { - struct cpuidle_device *dev = __this_cpu_read(cpuidle_devices); - struct cpuidle_driver *drv = cpuidle_get_cpu_driver(dev); int index; - if (cpuidle_not_available(drv, dev)) - goto fallback; - /* * Find the deepest state with ->enter_freeze present, which guarantees * that interrupts won't be enabled when it exits and allows the tick to * be frozen safely. */ - index = cpuidle_find_deepest_state(drv, dev, true); - if (index >= 0) { + index = find_deepest_state(drv, dev, true); + if (index >= 0) enter_freeze_proper(drv, dev, index); - local_irq_enable(); - return; - } - /* - * It is not safe to freeze the tick, find the deepest state available - * at all and try to enter it normally. - */ - index = cpuidle_find_deepest_state(drv, dev, false); - if (index >= 0) { - cpuidle_enter(drv, dev, index); - return; - } - - fallback: - arch_cpu_idle(); + return index; } /** @@ -217,9 +202,6 @@ int cpuidle_enter_state(struct cpuidle_device *dev, struct cpuidle_driver *drv, */ int cpuidle_select(struct cpuidle_driver *drv, struct cpuidle_device *dev) { - if (cpuidle_not_available(drv, dev)) - return -ENODEV; - return cpuidle_curr_governor->select(drv, dev); } diff --git a/include/linux/cpuidle.h b/include/linux/cpuidle.h index f551a9299ac9..306178d7309f 100644 --- a/include/linux/cpuidle.h +++ b/include/linux/cpuidle.h @@ -126,6 +126,8 @@ struct cpuidle_driver { #ifdef CONFIG_CPU_IDLE extern void disable_cpuidle(void); +extern bool cpuidle_not_available(struct cpuidle_driver *drv, + struct cpuidle_device *dev); extern int cpuidle_select(struct cpuidle_driver *drv, struct cpuidle_device *dev); @@ -150,11 +152,17 @@ extern void cpuidle_resume(void); extern int cpuidle_enable_device(struct cpuidle_device *dev); extern void cpuidle_disable_device(struct cpuidle_device *dev); extern int cpuidle_play_dead(void); -extern void cpuidle_enter_freeze(void); +extern int cpuidle_find_deepest_state(struct cpuidle_driver *drv, + struct cpuidle_device *dev); +extern int cpuidle_enter_freeze(struct cpuidle_driver *drv, + struct cpuidle_device *dev); extern struct cpuidle_driver *cpuidle_get_cpu_driver(struct cpuidle_device *dev); #else static inline void disable_cpuidle(void) { } +static inline bool cpuidle_not_available(struct cpuidle_driver *drv, + struct cpuidle_device *dev) +{return true; } static inline int cpuidle_select(struct cpuidle_driver *drv, struct cpuidle_device *dev) {return -ENODEV; } @@ -183,7 +191,12 @@ static inline int cpuidle_enable_device(struct cpuidle_device *dev) {return -ENODEV; } static inline void cpuidle_disable_device(struct cpuidle_device *dev) { } static inline int cpuidle_play_dead(void) {return -ENODEV; } -static inline void cpuidle_enter_freeze(void) { } +static inline int cpuidle_find_deepest_state(struct cpuidle_driver *drv, + struct cpuidle_device *dev) +{return -ENODEV; } +static inline int cpuidle_enter_freeze(struct cpuidle_driver *drv, + struct cpuidle_device *dev) +{return -ENODEV; } static inline struct cpuidle_driver *cpuidle_get_cpu_driver( struct cpuidle_device *dev) {return NULL; } #endif diff --git a/kernel/sched/idle.c b/kernel/sched/idle.c index 84b93b68482a..80014a178342 100644 --- a/kernel/sched/idle.c +++ b/kernel/sched/idle.c @@ -82,6 +82,7 @@ static void cpuidle_idle_call(void) struct cpuidle_driver *drv = cpuidle_get_cpu_driver(dev); int next_state, entered_state; unsigned int broadcast; + bool reflect; /* * Check if the idle task must be rescheduled. If it is the @@ -105,6 +106,9 @@ static void cpuidle_idle_call(void) */ rcu_idle_enter(); + if (cpuidle_not_available(drv, dev)) + goto use_default; + /* * Suspend-to-idle ("freeze") is a system state in which all user space * has been frozen, all I/O devices have been suspended and the only @@ -115,15 +119,22 @@ static void cpuidle_idle_call(void) * until a proper wakeup interrupt happens. */ if (idle_should_freeze()) { - cpuidle_enter_freeze(); - goto exit_idle; - } + entered_state = cpuidle_enter_freeze(drv, dev); + if (entered_state >= 0) { + local_irq_enable(); + goto exit_idle; + } - /* - * Ask the cpuidle framework to choose a convenient idle state. - * Fall back to the default arch idle method on errors. - */ - next_state = cpuidle_select(drv, dev); + reflect = false; + next_state = cpuidle_find_deepest_state(drv, dev); + } else { + reflect = true; + /* + * Ask the cpuidle framework to choose a convenient idle state. + */ + next_state = cpuidle_select(drv, dev); + } + /* Fall back to the default arch idle method on errors. */ if (next_state < 0) goto use_default; @@ -170,7 +181,8 @@ static void cpuidle_idle_call(void) /* * Give the governor an opportunity to reflect on the outcome */ - cpuidle_reflect(dev, entered_state); + if (reflect) + cpuidle_reflect(dev, entered_state); exit_idle: __current_set_polling(); -- cgit v1.2.3-59-g8ed1b From d677772e1358924bf487cd833bdc4d50f3f6f64d Mon Sep 17 00:00:00 2001 From: Boris BREZILLON Date: Mon, 2 Mar 2015 10:18:17 +0100 Subject: watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND The watchdog interrupt (only used when activating software watchdog) shouldn't be suspended when entering suspend mode, because it is shared with a timer device (which request the line with IRQF_NO_SUSPEND) and once the watchdog "Mode Register" has been written, it cannot be changed (which means we cannot disable the watchdog interrupt when entering suspend). Signed-off-by: Boris Brezillon Reviewed-by: Alexandre Belloni Acked-by: Guenter Roeck Acked-by: Nicolas Ferre Signed-off-by: Rafael J. Wysocki --- drivers/watchdog/at91sam9_wdt.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/watchdog/at91sam9_wdt.c b/drivers/watchdog/at91sam9_wdt.c index 6df940528fd2..1443b3c391de 100644 --- a/drivers/watchdog/at91sam9_wdt.c +++ b/drivers/watchdog/at91sam9_wdt.c @@ -208,7 +208,8 @@ static int at91_wdt_init(struct platform_device *pdev, struct at91wdt *wdt) if ((tmp & AT91_WDT_WDFIEN) && wdt->irq) { err = request_irq(wdt->irq, wdt_interrupt, - IRQF_SHARED | IRQF_IRQPOLL, + IRQF_SHARED | IRQF_IRQPOLL | + IRQF_NO_SUSPEND, pdev->name, wdt); if (err) return err; -- cgit v1.2.3-59-g8ed1b From 2c7af5ba65cfb0145ad8e11f856035c10ba0d22c Mon Sep 17 00:00:00 2001 From: Boris BREZILLON Date: Mon, 2 Mar 2015 10:18:18 +0100 Subject: tty: serial: atmel: rework interrupt and wakeup handling The IRQ line connected to the DBGU UART is often shared with a timer device which request the IRQ with IRQF_NO_SUSPEND. Since the UART driver is correctly disabling IRQs when entering suspend we can safely request the IRQ with IRQF_COND_SUSPEND so that irq core will not complain about mixing IRQF_NO_SUSPEND and !IRQF_NO_SUSPEND. Rework the interrupt handler to wake the system up when an interrupt happens on the DEBUG_UART while the system is suspended. Signed-off-by: Boris Brezillon Reviewed-by: Alexandre Belloni Acked-by: Nicolas Ferre Acked-by: Mark Rutland Signed-off-by: Rafael J. Wysocki --- drivers/tty/serial/atmel_serial.c | 49 +++++++++++++++++++++++++++++++++++---- 1 file changed, 45 insertions(+), 4 deletions(-) diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 846552bff67d..4e959c43f680 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -47,6 +47,7 @@ #include #include #include +#include #include #include @@ -173,6 +174,12 @@ struct atmel_uart_port { bool ms_irq_enabled; bool is_usart; /* usart or uart */ struct timer_list uart_timer; /* uart timer */ + + bool suspended; + unsigned int pending; + unsigned int pending_status; + spinlock_t lock_suspended; + int (*prepare_rx)(struct uart_port *port); int (*prepare_tx)(struct uart_port *port); void (*schedule_rx)(struct uart_port *port); @@ -1179,12 +1186,15 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) { struct uart_port *port = dev_id; struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); - unsigned int status, pending, pass_counter = 0; + unsigned int status, pending, mask, pass_counter = 0; bool gpio_handled = false; + spin_lock(&atmel_port->lock_suspended); + do { status = atmel_get_lines_status(port); - pending = status & UART_GET_IMR(port); + mask = UART_GET_IMR(port); + pending = status & mask; if (!gpio_handled) { /* * Dealing with GPIO interrupt @@ -1206,11 +1216,21 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) if (!pending) break; + if (atmel_port->suspended) { + atmel_port->pending |= pending; + atmel_port->pending_status = status; + UART_PUT_IDR(port, mask); + pm_system_wakeup(); + break; + } + atmel_handle_receive(port, pending); atmel_handle_status(port, pending, status); atmel_handle_transmit(port, pending); } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT); + spin_unlock(&atmel_port->lock_suspended); + return pass_counter ? IRQ_HANDLED : IRQ_NONE; } @@ -1742,7 +1762,8 @@ static int atmel_startup(struct uart_port *port) /* * Allocate the IRQ */ - retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED, + retval = request_irq(port->irq, atmel_interrupt, + IRQF_SHARED | IRQF_COND_SUSPEND, tty ? tty->name : "atmel_serial", port); if (retval) { dev_err(port->dev, "atmel_startup - Can't get irq\n"); @@ -2513,8 +2534,14 @@ static int atmel_serial_suspend(struct platform_device *pdev, /* we can not wake up if we're running on slow clock */ atmel_port->may_wakeup = device_may_wakeup(&pdev->dev); - if (atmel_serial_clk_will_stop()) + if (atmel_serial_clk_will_stop()) { + unsigned long flags; + + spin_lock_irqsave(&atmel_port->lock_suspended, flags); + atmel_port->suspended = true; + spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); device_set_wakeup_enable(&pdev->dev, 0); + } uart_suspend_port(&atmel_uart, port); @@ -2525,6 +2552,18 @@ static int atmel_serial_resume(struct platform_device *pdev) { struct uart_port *port = platform_get_drvdata(pdev); struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned long flags; + + spin_lock_irqsave(&atmel_port->lock_suspended, flags); + if (atmel_port->pending) { + atmel_handle_receive(port, atmel_port->pending); + atmel_handle_status(port, atmel_port->pending, + atmel_port->pending_status); + atmel_handle_transmit(port, atmel_port->pending); + atmel_port->pending = 0; + } + atmel_port->suspended = false; + spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); uart_resume_port(&atmel_uart, port); device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup); @@ -2593,6 +2632,8 @@ static int atmel_serial_probe(struct platform_device *pdev) port->backup_imr = 0; port->uart.line = ret; + spin_lock_init(&port->lock_suspended); + ret = atmel_init_gpios(port, &pdev->dev); if (ret < 0) dev_err(&pdev->dev, "%s", -- cgit v1.2.3-59-g8ed1b From 7438b633a6b073d66a3fa3678ec0dd5928caa4af Mon Sep 17 00:00:00 2001 From: Mark Rutland Date: Wed, 4 Mar 2015 20:00:40 +0000 Subject: genirq / PM: describe IRQF_COND_SUSPEND With certain restrictions it is possible for a wakeup device to share an IRQ with an IRQF_NO_SUSPEND user, and the warnings introduced by commit cab303be91dc47942bc25de33dc1140123540800 are spurious. The new IRQF_COND_SUSPEND flag allows drivers to tell the core when these restrictions are met, allowing spurious warnings to be silenced. This patch documents how IRQF_COND_SUSPEND is expected to be used, updating some of the text now made invalid by its addition. Signed-off-by: Mark Rutland Signed-off-by: Rafael J. Wysocki --- Documentation/power/suspend-and-interrupts.txt | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) diff --git a/Documentation/power/suspend-and-interrupts.txt b/Documentation/power/suspend-and-interrupts.txt index 50493c9284b4..8afb29a8604a 100644 --- a/Documentation/power/suspend-and-interrupts.txt +++ b/Documentation/power/suspend-and-interrupts.txt @@ -112,8 +112,9 @@ any special interrupt handling logic for it to work. IRQF_NO_SUSPEND and enable_irq_wake() ------------------------------------- -There are no valid reasons to use both enable_irq_wake() and the IRQF_NO_SUSPEND -flag on the same IRQ. +There are very few valid reasons to use both enable_irq_wake() and the +IRQF_NO_SUSPEND flag on the same IRQ, and it is never valid to use both for the +same device. First of all, if the IRQ is not shared, the rules for handling IRQF_NO_SUSPEND interrupts (interrupt handlers are invoked after suspend_device_irqs()) are @@ -122,4 +123,13 @@ handlers are not invoked after suspend_device_irqs()). Second, both enable_irq_wake() and IRQF_NO_SUSPEND apply to entire IRQs and not to individual interrupt handlers, so sharing an IRQ between a system wakeup -interrupt source and an IRQF_NO_SUSPEND interrupt source does not make sense. +interrupt source and an IRQF_NO_SUSPEND interrupt source does not generally +make sense. + +In rare cases an IRQ can be shared between a wakeup device driver and an +IRQF_NO_SUSPEND user. In order for this to be safe, the wakeup device driver +must be able to discern spurious IRQs from genuine wakeup events (signalling +the latter to the core with pm_system_wakeup()), must use enable_irq_wake() to +ensure that the IRQ will function as a wakeup source, and must request the IRQ +with IRQF_COND_SUSPEND to tell the core that it meets these requirements. If +these requirements are not met, it is not valid to use IRQF_COND_SUSPEND. -- cgit v1.2.3-59-g8ed1b From f5c0a122800c301eecef93275b0c5d58bb4c15d9 Mon Sep 17 00:00:00 2001 From: Josef Bacik Date: Mon, 2 Mar 2015 12:51:02 -0500 Subject: Btrfs: remove extra run_delayed_refs in update_cowonly_root This got added with my dirty_bgs patch, it's not needed. Thanks, Signed-off-by: Josef Bacik Signed-off-by: Chris Mason --- fs/btrfs/transaction.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c index 038fcf6051e0..323c6541d3dc 100644 --- a/fs/btrfs/transaction.c +++ b/fs/btrfs/transaction.c @@ -1052,9 +1052,6 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans, ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1); if (ret) return ret; - ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1); - if (ret) - return ret; } return 0; -- cgit v1.2.3-59-g8ed1b From 3a8b36f378060d20062a0918e99fae39ff077bf0 Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Sun, 1 Mar 2015 20:36:00 +0000 Subject: Btrfs: fix data loss in the fast fsync path When using the fast file fsync code path we can miss the fact that new writes happened since the last file fsync and therefore return without waiting for the IO to finish and write the new extents to the fsync log. Here's an example scenario where the fsync will miss the fact that new file data exists that wasn't yet durably persisted: 1. fs_info->last_trans_committed == N - 1 and current transaction is transaction N (fs_info->generation == N); 2. do a buffered write; 3. fsync our inode, this clears our inode's full sync flag, starts an ordered extent and waits for it to complete - when it completes at btrfs_finish_ordered_io(), the inode's last_trans is set to the value N (via btrfs_update_inode_fallback -> btrfs_update_inode -> btrfs_set_inode_last_trans); 4. transaction N is committed, so fs_info->last_trans_committed is now set to the value N and fs_info->generation remains with the value N; 5. do another buffered write, when this happens btrfs_file_write_iter sets our inode's last_trans to the value N + 1 (that is fs_info->generation + 1 == N + 1); 6. transaction N + 1 is started and fs_info->generation now has the value N + 1; 7. transaction N + 1 is committed, so fs_info->last_trans_committed is set to the value N + 1; 8. fsync our inode - because it doesn't have the full sync flag set, we only start the ordered extent, we don't wait for it to complete (only in a later phase) therefore its last_trans field has the value N + 1 set previously by btrfs_file_write_iter(), and so we have: inode->last_trans <= fs_info->last_trans_committed (N + 1) (N + 1) Which made us not log the last buffered write and exit the fsync handler immediately, returning success (0) to user space and resulting in data loss after a crash. This can actually be triggered deterministically and the following excerpt from a testcase I made for xfstests triggers the issue. It moves a dummy file across directories and then fsyncs the old parent directory - this is just to trigger a transaction commit, so moving files around isn't directly related to the issue but it was chosen because running 'sync' for example does more than just committing the current transaction, as it flushes/waits for all file data to be persisted. The issue can also happen at random periods, since the transaction kthread periodicaly commits the current transaction (about every 30 seconds by default). The body of the test is: _scratch_mkfs >> $seqres.full 2>&1 _init_flakey _mount_flakey # Create our main test file 'foo', the one we check for data loss. # By doing an fsync against our file, it makes btrfs clear the 'needs_full_sync' # bit from its flags (btrfs inode specific flags). $XFS_IO_PROG -f -c "pwrite -S 0xaa 0 8K" \ -c "fsync" $SCRATCH_MNT/foo | _filter_xfs_io # Now create one other file and 2 directories. We will move this second file # from one directory to the other later because it forces btrfs to commit its # currently open transaction if we fsync the old parent directory. This is # necessary to trigger the data loss bug that affected btrfs. mkdir $SCRATCH_MNT/testdir_1 touch $SCRATCH_MNT/testdir_1/bar mkdir $SCRATCH_MNT/testdir_2 # Make sure everything is durably persisted. sync # Write more 8Kb of data to our file. $XFS_IO_PROG -c "pwrite -S 0xbb 8K 8K" $SCRATCH_MNT/foo | _filter_xfs_io # Move our 'bar' file into a new directory. mv $SCRATCH_MNT/testdir_1/bar $SCRATCH_MNT/testdir_2/bar # Fsync our first directory. Because it had a file moved into some other # directory, this made btrfs commit the currently open transaction. This is # a condition necessary to trigger the data loss bug. $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/testdir_1 # Now fsync our main test file. If the fsync succeeds, we expect the 8Kb of # data we wrote previously to be persisted and available if a crash happens. # This did not happen with btrfs, because of the transaction commit that # happened when we fsynced the parent directory. $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo # Simulate a crash/power loss. _load_flakey_table $FLAKEY_DROP_WRITES _unmount_flakey _load_flakey_table $FLAKEY_ALLOW_WRITES _mount_flakey # Now check that all data we wrote before are available. echo "File content after log replay:" od -t x1 $SCRATCH_MNT/foo status=0 exit The expected golden output for the test, which is what we get with this fix applied (or when running against ext3/4 and xfs), is: wrote 8192/8192 bytes at offset 0 XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec) wrote 8192/8192 bytes at offset 8192 XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec) File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa * 0020000 bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb * 0040000 Without this fix applied, the output shows the test file does not have the second 8Kb extent that we successfully fsynced: wrote 8192/8192 bytes at offset 0 XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec) wrote 8192/8192 bytes at offset 8192 XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec) File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa * 0020000 So fix this by skipping the fsync only if we're doing a full sync and if the inode's last_trans is <= fs_info->last_trans_committed, or if the inode is already in the log. Also remove setting the inode's last_trans in btrfs_file_write_iter since it's useless/unreliable. Also because btrfs_file_write_iter no longer sets inode->last_trans to fs_info->generation + 1, don't set last_trans to 0 if we bail out and don't bail out if last_trans is 0, otherwise something as simple as the following example wouldn't log the second write on the last fsync: 1. write to file 2. fsync file 3. fsync file |--> btrfs_inode_in_log() returns true and it set last_trans to 0 4. write to file |--> btrfs_file_write_iter() no longers sets last_trans, so it remained with a value of 0 5. fsync |--> inode->last_trans == 0, so it bails out without logging the second write A test case for xfstests will be sent soon. CC: Signed-off-by: Filipe Manana Signed-off-by: Chris Mason --- fs/btrfs/file.c | 56 ++++++++++++++++++++++++++++---------------------------- 1 file changed, 28 insertions(+), 28 deletions(-) diff --git a/fs/btrfs/file.c b/fs/btrfs/file.c index b476e5645034..6351947c9bb0 100644 --- a/fs/btrfs/file.c +++ b/fs/btrfs/file.c @@ -1811,22 +1811,10 @@ static ssize_t btrfs_file_write_iter(struct kiocb *iocb, mutex_unlock(&inode->i_mutex); /* - * we want to make sure fsync finds this change - * but we haven't joined a transaction running right now. - * - * Later on, someone is sure to update the inode and get the - * real transid recorded. - * - * We set last_trans now to the fs_info generation + 1, - * this will either be one more than the running transaction - * or the generation used for the next transaction if there isn't - * one running right now. - * * We also have to set last_sub_trans to the current log transid, * otherwise subsequent syncs to a file that's been synced in this * transaction will appear to have already occured. */ - BTRFS_I(inode)->last_trans = root->fs_info->generation + 1; BTRFS_I(inode)->last_sub_trans = root->log_transid; if (num_written > 0) { err = generic_write_sync(file, pos, num_written); @@ -1959,25 +1947,37 @@ int btrfs_sync_file(struct file *file, loff_t start, loff_t end, int datasync) atomic_inc(&root->log_batch); /* - * check the transaction that last modified this inode - * and see if its already been committed - */ - if (!BTRFS_I(inode)->last_trans) { - mutex_unlock(&inode->i_mutex); - goto out; - } - - /* - * if the last transaction that changed this file was before - * the current transaction, we can bail out now without any - * syncing + * If the last transaction that changed this file was before the current + * transaction and we have the full sync flag set in our inode, we can + * bail out now without any syncing. + * + * Note that we can't bail out if the full sync flag isn't set. This is + * because when the full sync flag is set we start all ordered extents + * and wait for them to fully complete - when they complete they update + * the inode's last_trans field through: + * + * btrfs_finish_ordered_io() -> + * btrfs_update_inode_fallback() -> + * btrfs_update_inode() -> + * btrfs_set_inode_last_trans() + * + * So we are sure that last_trans is up to date and can do this check to + * bail out safely. For the fast path, when the full sync flag is not + * set in our inode, we can not do it because we start only our ordered + * extents and don't wait for them to complete (that is when + * btrfs_finish_ordered_io runs), so here at this point their last_trans + * value might be less than or equals to fs_info->last_trans_committed, + * and setting a speculative last_trans for an inode when a buffered + * write is made (such as fs_info->generation + 1 for example) would not + * be reliable since after setting the value and before fsync is called + * any number of transactions can start and commit (transaction kthread + * commits the current transaction periodically), and a transaction + * commit does not start nor waits for ordered extents to complete. */ smp_mb(); if (btrfs_inode_in_log(inode, root->fs_info->generation) || - BTRFS_I(inode)->last_trans <= - root->fs_info->last_trans_committed) { - BTRFS_I(inode)->last_trans = 0; - + (full_sync && BTRFS_I(inode)->last_trans <= + root->fs_info->last_trans_committed)) { /* * We'v had everything committed since the last time we were * modified so clear this flag in case it was set for whatever -- cgit v1.2.3-59-g8ed1b From dd9ef135e3542ffc621c4eb7f0091870ec7a1504 Mon Sep 17 00:00:00 2001 From: Quentin Casasnovas Date: Tue, 3 Mar 2015 16:31:38 +0100 Subject: Btrfs:__add_inode_ref: out of bounds memory read when looking for extended ref. Improper arithmetics when calculting the address of the extended ref could lead to an out of bounds memory read and kernel panic. Signed-off-by: Quentin Casasnovas Reviewed-by: David Sterba cc: stable@vger.kernel.org # v3.7+ Signed-off-by: Chris Mason --- fs/btrfs/tree-log.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c index f96996a1b70c..9a1c1711f360 100644 --- a/fs/btrfs/tree-log.c +++ b/fs/btrfs/tree-log.c @@ -1012,7 +1012,7 @@ again: base = btrfs_item_ptr_offset(leaf, path->slots[0]); while (cur_offset < item_size) { - extref = (struct btrfs_inode_extref *)base + cur_offset; + extref = (struct btrfs_inode_extref *)(base + cur_offset); victim_name_len = btrfs_inode_extref_name_len(leaf, extref); -- cgit v1.2.3-59-g8ed1b From 8b5f5a073fda33bbe96b3eb1bffca32010ccaf0e Mon Sep 17 00:00:00 2001 From: Laura Abbott Date: Wed, 25 Feb 2015 14:14:55 -0800 Subject: arm64: Don't use is_module_addr in setting page attributes The set_memory_* functions currently only support module addresses. The addresses are validated using is_module_addr. That function is special though and relies on internal state in the module subsystem to work properly. At the time of module initialization and calling set_memory_*, it's too early for is_module_addr to work properly so it always returns false. Rather than be subject to the whims of the module state, just bounds check against the module virtual address range. Signed-off-by: Laura Abbott Signed-off-by: Catalin Marinas --- arch/arm64/mm/pageattr.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/arch/arm64/mm/pageattr.c b/arch/arm64/mm/pageattr.c index bb0ea94c4ba1..1d3ec3ddd84b 100644 --- a/arch/arm64/mm/pageattr.c +++ b/arch/arm64/mm/pageattr.c @@ -51,7 +51,10 @@ static int change_memory_common(unsigned long addr, int numpages, WARN_ON_ONCE(1); } - if (!is_module_address(start) || !is_module_address(end - 1)) + if (start < MODULES_VADDR || start >= MODULES_END) + return -EINVAL; + + if (end < MODULES_VADDR || end >= MODULES_END) return -EINVAL; data.set_mask = set_mask; -- cgit v1.2.3-59-g8ed1b From 168e47f2a6581fdbc5bb1845aeca1e50e2bc5c4b Mon Sep 17 00:00:00 2001 From: Laura Abbott Date: Wed, 25 Feb 2015 14:14:57 -0800 Subject: kernel/module.c: Update debug alignment after symtable generation When CONFIG_DEBUG_SET_MODULE_RONX is enabled, the sizes of module sections are aligned up so appropriate permissions can be applied. Adjusting for the symbol table may cause them to become unaligned. Make sure to re-align the sizes afterward. Signed-off-by: Laura Abbott Acked-by: Rusty Russell Signed-off-by: Catalin Marinas --- kernel/module.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/kernel/module.c b/kernel/module.c index b34813f725e9..cc93cf68653c 100644 --- a/kernel/module.c +++ b/kernel/module.c @@ -2313,11 +2313,13 @@ static void layout_symtab(struct module *mod, struct load_info *info) info->symoffs = ALIGN(mod->core_size, symsect->sh_addralign ?: 1); info->stroffs = mod->core_size = info->symoffs + ndst * sizeof(Elf_Sym); mod->core_size += strtab_size; + mod->core_size = debug_align(mod->core_size); /* Put string table section at end of init part of module. */ strsect->sh_flags |= SHF_ALLOC; strsect->sh_entsize = get_offset(mod, &mod->init_size, strsect, info->index.str) | INIT_OFFSET_MASK; + mod->init_size = debug_align(mod->init_size); pr_debug("\t%s\n", info->secstrings + strsect->sh_name); } -- cgit v1.2.3-59-g8ed1b From d124380674b58f62d0ef974630d74d67bb8afeb0 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Thu, 5 Mar 2015 20:49:06 +0300 Subject: ALSA: opl3: small array underflow There is a missing lower bound check on "pitchbend" so it means we can read up to 6 elements before the start of the opl3_note_table[] array. Thanks to Clemens Ladisch for his help with this patch. Signed-off-by: Dan Carpenter Signed-off-by: Takashi Iwai --- sound/drivers/opl3/opl3_midi.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/sound/drivers/opl3/opl3_midi.c b/sound/drivers/opl3/opl3_midi.c index f62780ed64ad..7821b07415a7 100644 --- a/sound/drivers/opl3/opl3_midi.c +++ b/sound/drivers/opl3/opl3_midi.c @@ -105,6 +105,8 @@ static void snd_opl3_calc_pitch(unsigned char *fnum, unsigned char *blocknum, int pitchbend = chan->midi_pitchbend; int segment; + if (pitchbend < -0x2000) + pitchbend = -0x2000; if (pitchbend > 0x1FFF) pitchbend = 0x1FFF; -- cgit v1.2.3-59-g8ed1b From 70658b99490dd86cfdbf4fca117bbe2ef9a80d03 Mon Sep 17 00:00:00 2001 From: Hui Wang Date: Fri, 6 Mar 2015 14:03:57 +0800 Subject: ALSA: hda - One more Dell macine needs DELL1_MIC_NO_PRESENCE quirk Cc: BugLink: https://bugs.launchpad.net/bugs/1428947 Signed-off-by: Hui Wang Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index b2b24a8b3dac..526398a4a442 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -5209,6 +5209,13 @@ static const struct snd_hda_pin_quirk alc269_pin_fixup_tbl[] = { {0x17, 0x40000000}, {0x1d, 0x40700001}, {0x21, 0x02211040}), + SND_HDA_PIN_QUIRK(0x10ec0255, 0x1028, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE, + ALC255_STANDARD_PINS, + {0x12, 0x90a60170}, + {0x14, 0x90170140}, + {0x17, 0x40000000}, + {0x1d, 0x40700001}, + {0x21, 0x02211050}), SND_HDA_PIN_QUIRK(0x10ec0280, 0x103c, "HP", ALC280_FIXUP_HP_GPIO4, {0x12, 0x90a60130}, {0x13, 0x40000000}, -- cgit v1.2.3-59-g8ed1b From 45ba2154d12fc43b70312198ec47085f10be801a Mon Sep 17 00:00:00 2001 From: Aleksander Morgado Date: Fri, 6 Mar 2015 17:14:21 +0200 Subject: xhci: fix reporting of 0-sized URBs in control endpoint When a control transfer has a short data stage, the xHCI controller generates two transfer events: a COMP_SHORT_TX event that specifies the untransferred amount, and a COMP_SUCCESS event. But when the data stage is not short, only the COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless urb->actual_length was set already by a previous COMP_SHORT_TX event. The driver checks this by seeing whether urb->actual_length == 0, but this alone is the wrong test, as it is entirely possible for a short transfer to have an urb->actual_length = 0. This patch changes the xhci driver to rely on a new td->urb_length_set flag, which is set to true when a COMP_SHORT_TX event is received and the URB length updated at that stage. This fixes a bug which affected the HSO plugin, which relies on URBs with urb->actual_length == 0 to halt re-submitting the RX URB in the control endpoint. Cc: Signed-off-by: Aleksander Morgado Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 10 ++++++++-- drivers/usb/host/xhci.h | 3 +++ 2 files changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index b46b5b98a943..5fb66db89e05 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1946,7 +1946,7 @@ static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_td *td, if (event_trb != ep_ring->dequeue) { /* The event was for the status stage */ if (event_trb == td->last_trb) { - if (td->urb->actual_length != 0) { + if (td->urb_length_set) { /* Don't overwrite a previously set error code */ if ((*status == -EINPROGRESS || *status == 0) && @@ -1960,7 +1960,13 @@ static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_td *td, td->urb->transfer_buffer_length; } } else { - /* Maybe the event was for the data stage? */ + /* + * Maybe the event was for the data stage? If so, update + * already the actual_length of the URB and flag it as + * set, so that it is not overwritten in the event for + * the last TRB. + */ + td->urb_length_set = true; td->urb->actual_length = td->urb->transfer_buffer_length - EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)); diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 3b97f0582155..d0663931e5ba 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1,3 +1,4 @@ + /* * xHCI host controller driver * @@ -1291,6 +1292,8 @@ struct xhci_td { struct xhci_segment *start_seg; union xhci_trb *first_trb; union xhci_trb *last_trb; + /* actual_length of the URB has already been set */ + bool urb_length_set; }; /* xHCI command default timeout value */ -- cgit v1.2.3-59-g8ed1b From b8cb91e058cd0c0f02059c1207293c5b31d350fa Mon Sep 17 00:00:00 2001 From: Mathias Nyman Date: Fri, 6 Mar 2015 17:23:19 +0200 Subject: xhci: Workaround for PME stuck issues in Intel xhci The xhci in Intel Sunrisepoint and Cherryview platforms need a driver workaround for a Stuck PME that might either block PME events in suspend, or create spurious PME events preventing runtime suspend. Workaround is to clear a internal PME flag, BIT(28) in a vendor specific PMCTRL register at offset 0x80a4, in both suspend resume callbacks Without this, xhci connected usb devices might never be able to wake up the system from suspend, or prevent device from going to suspend (xhci d3) Cc: Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-pci.c | 30 ++++++++++++++++++++++++++++++ drivers/usb/host/xhci.h | 1 + 2 files changed, 31 insertions(+) diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 7f76c8a12f89..fd53c9ebd662 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -37,6 +37,9 @@ #define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI 0x8c31 #define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI 0x9c31 +#define PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI 0x22b5 +#define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI 0xa12f +#define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI 0x9d2f static const char hcd_name[] = "xhci_hcd"; @@ -133,6 +136,12 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI) { xhci->quirks |= XHCI_SPURIOUS_REBOOT; } + if (pdev->vendor == PCI_VENDOR_ID_INTEL && + (pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI || + pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI || + pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI)) { + xhci->quirks |= XHCI_PME_STUCK_QUIRK; + } if (pdev->vendor == PCI_VENDOR_ID_ETRON && pdev->device == PCI_DEVICE_ID_EJ168) { xhci->quirks |= XHCI_RESET_ON_RESUME; @@ -159,6 +168,21 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) "QUIRK: Resetting on resume"); } +/* + * Make sure PME works on some Intel xHCI controllers by writing 1 to clear + * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 + */ +static void xhci_pme_quirk(struct xhci_hcd *xhci) +{ + u32 val; + void __iomem *reg; + + reg = (void __iomem *) xhci->cap_regs + 0x80a4; + val = readl(reg); + writel(val | BIT(28), reg); + readl(reg); +} + /* called during probe() after chip reset completes */ static int xhci_pci_setup(struct usb_hcd *hcd) { @@ -283,6 +307,9 @@ static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) if (xhci->quirks & XHCI_COMP_MODE_QUIRK) pdev->no_d3cold = true; + if (xhci->quirks & XHCI_PME_STUCK_QUIRK) + xhci_pme_quirk(xhci); + return xhci_suspend(xhci, do_wakeup); } @@ -313,6 +340,9 @@ static int xhci_pci_resume(struct usb_hcd *hcd, bool hibernated) if (pdev->vendor == PCI_VENDOR_ID_INTEL) usb_enable_intel_xhci_ports(pdev); + if (xhci->quirks & XHCI_PME_STUCK_QUIRK) + xhci_pme_quirk(xhci); + retval = xhci_resume(xhci, hibernated); return retval; } diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index d0663931e5ba..265ab1771d24 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1566,6 +1566,7 @@ struct xhci_hcd { #define XHCI_SPURIOUS_WAKEUP (1 << 18) /* For controllers with a broken beyond repair streams implementation */ #define XHCI_BROKEN_STREAMS (1 << 19) +#define XHCI_PME_STUCK_QUIRK (1 << 20) unsigned int num_active_eps; unsigned int limit_active_eps; /* There are two roothubs to keep track of bus suspend info for */ -- cgit v1.2.3-59-g8ed1b From 9b5c9f043e7a70665b2eb092f316d5d5cd238d49 Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Tue, 10 Feb 2015 19:06:06 +0200 Subject: i2c: designware-baytrail: describe magic numbers The patch converts hardcoded numerical constants to a named ones. While here, align the variable name in get_sem() and reset_semaphore(). Signed-off-by: Andy Shevchenko Acked-by: David E. Box Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-baytrail.c | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-) diff --git a/drivers/i2c/busses/i2c-designware-baytrail.c b/drivers/i2c/busses/i2c-designware-baytrail.c index 5f1ff4cc5c34..e9cb3555dc79 100644 --- a/drivers/i2c/busses/i2c-designware-baytrail.c +++ b/drivers/i2c/busses/i2c-designware-baytrail.c @@ -22,22 +22,24 @@ #define SEMAPHORE_TIMEOUT 100 #define PUNIT_SEMAPHORE 0x7 +#define PUNIT_SEMAPHORE_BIT BIT(0) +#define PUNIT_SEMAPHORE_ACQUIRE BIT(1) static unsigned long acquired; static int get_sem(struct device *dev, u32 *sem) { - u32 reg_val; + u32 data; int ret; ret = iosf_mbi_read(BT_MBI_UNIT_PMC, BT_MBI_BUNIT_READ, PUNIT_SEMAPHORE, - ®_val); + &data); if (ret) { dev_err(dev, "iosf failed to read punit semaphore\n"); return ret; } - *sem = reg_val & 0x1; + *sem = data & PUNIT_SEMAPHORE_BIT; return 0; } @@ -52,9 +54,9 @@ static void reset_semaphore(struct device *dev) return; } - data = data & 0xfffffffe; + data &= ~PUNIT_SEMAPHORE_BIT; if (iosf_mbi_write(BT_MBI_UNIT_PMC, BT_MBI_BUNIT_WRITE, - PUNIT_SEMAPHORE, data)) + PUNIT_SEMAPHORE, data)) dev_err(dev, "iosf failed to reset punit semaphore during write\n"); } @@ -70,9 +72,9 @@ int baytrail_i2c_acquire(struct dw_i2c_dev *dev) if (!dev->acquire_lock) return 0; - /* host driver writes 0x2 to side band semaphore register */ + /* host driver writes to side band semaphore register */ ret = iosf_mbi_write(BT_MBI_UNIT_PMC, BT_MBI_BUNIT_WRITE, - PUNIT_SEMAPHORE, 0x2); + PUNIT_SEMAPHORE, PUNIT_SEMAPHORE_ACQUIRE); if (ret) { dev_err(dev->dev, "iosf punit semaphore request failed\n"); return ret; -- cgit v1.2.3-59-g8ed1b From 259aada436e13ec75a8b0f252a78e6577879008e Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Tue, 10 Feb 2015 19:06:07 +0200 Subject: i2c: designware-baytrail: fix typo in error path It seems we have same message for different return values in get_sem() and baytrail_i2c_acquire(). I suspect this is just a typo, so this patch fixes it. Signed-off-by: Andy Shevchenko Acked-by: David E. Box Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-baytrail.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/i2c/busses/i2c-designware-baytrail.c b/drivers/i2c/busses/i2c-designware-baytrail.c index e9cb3555dc79..9b6765554c70 100644 --- a/drivers/i2c/busses/i2c-designware-baytrail.c +++ b/drivers/i2c/busses/i2c-designware-baytrail.c @@ -99,8 +99,8 @@ int baytrail_i2c_acquire(struct dw_i2c_dev *dev) reset_semaphore(dev->dev); ret = iosf_mbi_read(BT_MBI_UNIT_PMC, BT_MBI_BUNIT_READ, - PUNIT_SEMAPHORE, &sem); - if (!ret) + PUNIT_SEMAPHORE, &sem); + if (ret) dev_err(dev->dev, "iosf failed to read punit semaphore\n"); else dev_err(dev->dev, "PUNIT SEM: %d\n", sem); -- cgit v1.2.3-59-g8ed1b From c8e043e6f717b0256b1cfc55d03c232e8a5c8cbd Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Tue, 10 Feb 2015 19:06:08 +0200 Subject: i2c: designware-baytrail: fix sparse warnings There is no need to export functions that are used as the callbacks in the struct dw_i2c_dev. Otherwise we get the following warnings: drivers/i2c/busses/i2c-designware-baytrail.c:63:5: warning: symbol 'baytrail_i2c_acquire' was not declared. Should it be static? drivers/i2c/busses/i2c-designware-baytrail.c:114:6: warning: symbol 'baytrail_i2c_release' was not declared. Should it be static? While here, do few indentation fixes, remove i2c_dw_eval_lock_support() from functions exported to the modules and redundant assignment of local sem variable. Signed-off-by: Andy Shevchenko Acked-by: David E. Box Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-baytrail.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-) diff --git a/drivers/i2c/busses/i2c-designware-baytrail.c b/drivers/i2c/busses/i2c-designware-baytrail.c index 9b6765554c70..d33474422003 100644 --- a/drivers/i2c/busses/i2c-designware-baytrail.c +++ b/drivers/i2c/busses/i2c-designware-baytrail.c @@ -17,7 +17,9 @@ #include #include #include + #include + #include "i2c-designware-core.h" #define SEMAPHORE_TIMEOUT 100 @@ -60,9 +62,9 @@ static void reset_semaphore(struct device *dev) dev_err(dev, "iosf failed to reset punit semaphore during write\n"); } -int baytrail_i2c_acquire(struct dw_i2c_dev *dev) +static int baytrail_i2c_acquire(struct dw_i2c_dev *dev) { - u32 sem = 0; + u32 sem; int ret; unsigned long start, end; @@ -109,9 +111,8 @@ int baytrail_i2c_acquire(struct dw_i2c_dev *dev) return -ETIMEDOUT; } -EXPORT_SYMBOL(baytrail_i2c_acquire); -void baytrail_i2c_release(struct dw_i2c_dev *dev) +static void baytrail_i2c_release(struct dw_i2c_dev *dev) { if (!dev || !dev->dev) return; @@ -123,7 +124,6 @@ void baytrail_i2c_release(struct dw_i2c_dev *dev) dev_dbg(dev->dev, "punit semaphore held for %ums\n", jiffies_to_msecs(jiffies - acquired)); } -EXPORT_SYMBOL(baytrail_i2c_release); int i2c_dw_eval_lock_support(struct dw_i2c_dev *dev) { @@ -139,7 +139,6 @@ int i2c_dw_eval_lock_support(struct dw_i2c_dev *dev) return 0; status = acpi_evaluate_integer(handle, "_SEM", NULL, &shared_host); - if (ACPI_FAILURE(status)) return 0; @@ -155,7 +154,6 @@ int i2c_dw_eval_lock_support(struct dw_i2c_dev *dev) return 0; } -EXPORT_SYMBOL(i2c_dw_eval_lock_support); MODULE_AUTHOR("David E. Box "); MODULE_DESCRIPTION("Baytrail I2C Semaphore driver"); -- cgit v1.2.3-59-g8ed1b From 30be774b38d845791b1acbd750f19e56c57f0185 Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Tue, 10 Feb 2015 19:06:09 +0200 Subject: i2c: designware-baytrail: cross-check lock functions It seems the idea behind the cross-check is to prevent acquire semaphore when there is no release callback and vice versa. Thus, patch fixes a typo. Signed-off-by: Andy Shevchenko Acked-by: David E. Box Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-baytrail.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-designware-baytrail.c b/drivers/i2c/busses/i2c-designware-baytrail.c index d33474422003..036d9bdc0aaa 100644 --- a/drivers/i2c/busses/i2c-designware-baytrail.c +++ b/drivers/i2c/busses/i2c-designware-baytrail.c @@ -71,7 +71,7 @@ static int baytrail_i2c_acquire(struct dw_i2c_dev *dev) if (!dev || !dev->dev) return -ENODEV; - if (!dev->acquire_lock) + if (!dev->release_lock) return 0; /* host driver writes to side band semaphore register */ -- cgit v1.2.3-59-g8ed1b From ebf2ef8f613433aaffac53aef2f6703445821fc6 Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Tue, 10 Feb 2015 19:06:10 +0200 Subject: i2c: designware-baytrail: baytrail_i2c_acquire() might sleep This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages while-loop to do-while and, though it is matter of taste, gives a chance to check one more time before report a timeout. Signed-off-by: Andy Shevchenko Acked-by: David E. Box Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-baytrail.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/i2c/busses/i2c-designware-baytrail.c b/drivers/i2c/busses/i2c-designware-baytrail.c index 036d9bdc0aaa..7d7ae97476e2 100644 --- a/drivers/i2c/busses/i2c-designware-baytrail.c +++ b/drivers/i2c/busses/i2c-designware-baytrail.c @@ -68,6 +68,8 @@ static int baytrail_i2c_acquire(struct dw_i2c_dev *dev) int ret; unsigned long start, end; + might_sleep(); + if (!dev || !dev->dev) return -ENODEV; @@ -85,7 +87,7 @@ static int baytrail_i2c_acquire(struct dw_i2c_dev *dev) /* host driver waits for bit 0 to be set in semaphore register */ start = jiffies; end = start + msecs_to_jiffies(SEMAPHORE_TIMEOUT); - while (!time_after(jiffies, end)) { + do { ret = get_sem(dev->dev, &sem); if (!ret && sem) { acquired = jiffies; @@ -95,7 +97,7 @@ static int baytrail_i2c_acquire(struct dw_i2c_dev *dev) } usleep_range(1000, 2000); - } + } while (time_before(jiffies, end)); dev_err(dev->dev, "punit semaphore timed out, resetting\n"); reset_semaphore(dev->dev); -- cgit v1.2.3-59-g8ed1b From 5d232112f94b0f3920dc4fec09688ef6cb5c09df Mon Sep 17 00:00:00 2001 From: Matt Porter Date: Tue, 3 Mar 2015 11:57:08 -0500 Subject: i2c: imx: add required clocks property to binding A clock specifier is required for i.MX I2C and is provided in all DTS implementations. Add this to the list of required properties in the binding. Signed-off-by: Matt Porter Signed-off-by: Wolfram Sang --- Documentation/devicetree/bindings/i2c/i2c-imx.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index 52d37fd8d3e5..ce4311d726ae 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -7,6 +7,7 @@ Required properties: - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC - reg : Should contain I2C/HS-I2C registers location and length - interrupts : Should contain I2C/HS-I2C interrupt +- clocks : Should contain the I2C/HS-I2C clock specifier Optional properties: - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. -- cgit v1.2.3-59-g8ed1b From 045f32dda9477d3ddf31a4fa862c487d0f747e33 Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Mon, 16 Feb 2015 08:27:49 +0200 Subject: Revert "tty/serial: of_serial: add DT alias ID handling" This reverts commit 6d01bb9dc82a60580f749062a48cb47cd5caca07. The exact same code was added in commit 3239fd31d4 (serial: of-serial: fetch line number from DT) a few lined above. Doing this once should be enough. Cc: Rob Herring Signed-off-by: Baruch Siach Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/of_serial.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 7ff61e24a195..33fb94f78967 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -133,10 +133,6 @@ static int of_platform_serial_setup(struct platform_device *ofdev, if (of_find_property(np, "no-loopback-test", NULL)) port->flags |= UPF_SKIP_TEST; - ret = of_alias_get_id(np, "serial"); - if (ret >= 0) - port->line = ret; - port->dev = &ofdev->dev; switch (type) { -- cgit v1.2.3-59-g8ed1b From ca8bb4aefb932e3da105f28cbfba36d57a931081 Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Sun, 15 Feb 2015 18:32:16 +0100 Subject: serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO" This reverts commit 0aa525d11859c1a4d5b78fdc704148e2ae03ae13. The conditional RX-FIFO read seems to cause spurious interrupts and we see just: |serial8250: too much work for irq29 The previous behaviour was "default" for decades and Marvell's 88f6282 SoC might not be the only that relies on it. Therefore the Omap fix is reverted for now. Fixes: 0aa525d11859 ("tty: serial: 8250_core: read only RX if there is something in the FIFO") Reported-By: Nicolas Schichan Debuged-By: Peter Hurley Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_core.c | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-) diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index e3b9570a1eff..deae122c9c4b 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -2138,8 +2138,8 @@ int serial8250_do_startup(struct uart_port *port) /* * Clear the interrupt registers. */ - if (serial_port_in(port, UART_LSR) & UART_LSR_DR) - serial_port_in(port, UART_RX); + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); serial_port_in(port, UART_IIR); serial_port_in(port, UART_MSR); @@ -2300,8 +2300,8 @@ dont_test_tx_en: * saved flags to avoid getting false values from polling * routines or the previous session. */ - if (serial_port_in(port, UART_LSR) & UART_LSR_DR) - serial_port_in(port, UART_RX); + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); serial_port_in(port, UART_IIR); serial_port_in(port, UART_MSR); up->lsr_saved_flags = 0; @@ -2394,8 +2394,7 @@ void serial8250_do_shutdown(struct uart_port *port) * Read data port to reset things, and then unlink from * the IRQ chain. */ - if (serial_port_in(port, UART_LSR) & UART_LSR_DR) - serial_port_in(port, UART_RX); + serial_port_in(port, UART_RX); serial8250_rpm_put(up); del_timer_sync(&up->timer); -- cgit v1.2.3-59-g8ed1b From f2e0ea861117bda073d1d7ffbd3120c07c0d5d34 Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 6 Mar 2015 10:49:21 +0000 Subject: Change email address for 8250_pci I'm still receiving reports to my email address, so let's point this at the linux-serial mailing list instead. Cc: Signed-off-by: Russell King Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index daf2c82984e9..65dd3ad442ea 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -69,7 +69,7 @@ static void moan_device(const char *str, struct pci_dev *dev) "Please send the output of lspci -vv, this\n" "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n" "manufacturer and name of serial board or\n" - "modem board to rmk+serial@arm.linux.org.uk.\n", + "modem board to .\n", pci_name(dev), str, dev->vendor, dev->device, dev->subsystem_vendor, dev->subsystem_device); } -- cgit v1.2.3-59-g8ed1b From 6262a3692b921a82075695c5c6d10f4a6bcc5fac Mon Sep 17 00:00:00 2001 From: Wang YanQing Date: Sat, 7 Mar 2015 01:13:03 +0800 Subject: serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S Commit 8b5c913f7ee6464849570bacb6bcd9ef0eaf7dce ("serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection") trigger one redundant entry report message. This patch fix it. Reported-by: Russell King Signed-off-by: Wang YanQing Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_pci.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 65dd3ad442ea..285b875fd187 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -5415,10 +5415,6 @@ static struct pci_device_id serial_pci_tbl[] = { PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b0_bt_2_115200 }, - { PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH352_2S, - PCI_ANY_ID, PCI_ANY_ID, - 0, 0, pbn_b0_bt_2_115200 }, - { PCIE_VENDOR_ID_WCH, PCIE_DEVICE_ID_WCH_CH384_4S, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_wch384_4 }, -- cgit v1.2.3-59-g8ed1b From 7cf91108d44dbef3d48766fd0e7f7347c2e48bda Mon Sep 17 00:00:00 2001 From: Wang YanQing Date: Sat, 7 Mar 2015 01:08:35 +0800 Subject: serial:8250:8250_pci: delete unneeded quirk entries These quirk entries have the same effect as default quirk entry, so we can just delete them. Signed-off-by: Wang YanQing Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_pci.c | 14 -------------- 1 file changed, 14 deletions(-) diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 285b875fd187..892eb32cdef4 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -1987,13 +1987,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .subdevice = PCI_ANY_ID, .setup = byt_serial_setup, }, - { - .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_QRK_UART, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .setup = pci_default_setup, - }, { .vendor = PCI_VENDOR_ID_INTEL, .device = PCI_DEVICE_ID_INTEL_BSW_UART1, @@ -2199,13 +2192,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { /* * PLX */ - { - .vendor = PCI_VENDOR_ID_PLX, - .device = PCI_DEVICE_ID_PLX_9030, - .subvendor = PCI_SUBVENDOR_ID_PERLE, - .subdevice = PCI_ANY_ID, - .setup = pci_default_setup, - }, { .vendor = PCI_VENDOR_ID_PLX, .device = PCI_DEVICE_ID_PLX_9050, -- cgit v1.2.3-59-g8ed1b From dfd37668ea6d5029fb5d8a66ea5e202d0655fad7 Mon Sep 17 00:00:00 2001 From: Desmond Liu Date: Thu, 26 Feb 2015 16:35:57 -0800 Subject: serial: 8250_dw: Fix get_mctrl behaviour Fixed behaviour of get_mctrl() serial driver function as documented in: https://www.kernel.org/doc/Documentation/serial/driver Added device-tree properties 'dcd-override', 'dsr-override', 'cts-override', and 'ri-override' specific to the Synopsis 8250 DesignWare UART driver. Allows one to force Data Carrier Detect, Clear To Send, and Data Set Ready signals to permanently be reported as active. The Ring indicator can be forced to be reported as inactive. It is possible that if modem control signalling is enabled on a port that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the driver can hang indefinitely waiting for the state to change. The new DT properties allow the driver to ignore the state of these pins on serial ports that don't support them, as recommended in the kernel documentation. Reviewed-by: JD (Jiandong) Zheng Signed-off-by: Jonathan Richardson Signed-off-by: Greg Kroah-Hartman --- .../bindings/serial/snps-dw-apb-uart.txt | 16 +++++++++++ drivers/tty/serial/8250/8250_dw.c | 32 ++++++++++++++++++++++ 2 files changed, 48 insertions(+) diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index 7f76214f728a..289c40ed7470 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -21,6 +21,18 @@ Optional properties: - reg-io-width : the size (in bytes) of the IO accesses that should be performed on the device. If this property is not present then single byte accesses are used. +- dcd-override : Override the DCD modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- dsr-override : Override the DTS modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- cts-override : Override the CTS modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- ri-override : Override the RI modem status signal. This signal will always be + reported as inactive instead of being obtained from the modem status register. + Define this if your serial port does not use this pin. Example: @@ -31,6 +43,10 @@ Example: interrupts = <10>; reg-shift = <2>; reg-io-width = <4>; + dcd-override; + dsr-override; + cts-override; + ri-override; }; Example with one clock: diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c index e60116235836..2ab229ddee38 100644 --- a/drivers/tty/serial/8250/8250_dw.c +++ b/drivers/tty/serial/8250/8250_dw.c @@ -59,6 +59,8 @@ struct dw8250_data { u8 usr_reg; int last_mcr; int line; + int msr_mask_on; + int msr_mask_off; struct clk *clk; struct clk *pclk; struct reset_control *rst; @@ -81,6 +83,12 @@ static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value) value &= ~UART_MSR_DCTS; } + /* Override any modem control signals if needed */ + if (offset == UART_MSR) { + value |= d->msr_mask_on; + value &= ~d->msr_mask_off; + } + return value; } @@ -334,6 +342,30 @@ static int dw8250_probe_of(struct uart_port *p, if (id >= 0) p->line = id; + if (of_property_read_bool(np, "dcd-override")) { + /* Always report DCD as active */ + data->msr_mask_on |= UART_MSR_DCD; + data->msr_mask_off |= UART_MSR_DDCD; + } + + if (of_property_read_bool(np, "dsr-override")) { + /* Always report DSR as active */ + data->msr_mask_on |= UART_MSR_DSR; + data->msr_mask_off |= UART_MSR_DDSR; + } + + if (of_property_read_bool(np, "cts-override")) { + /* Always report DSR as active */ + data->msr_mask_on |= UART_MSR_DSR; + data->msr_mask_off |= UART_MSR_DDSR; + } + + if (of_property_read_bool(np, "ri-override")) { + /* Always report Ring indicator as inactive */ + data->msr_mask_off |= UART_MSR_RI; + data->msr_mask_off |= UART_MSR_TERI; + } + /* clock got configured through clk api, all done */ if (p->uartclk) return 0; -- cgit v1.2.3-59-g8ed1b From f0bf0bd07943bfde8f5ac39a32664810a379c7d3 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Fri, 27 Feb 2015 18:40:31 +0100 Subject: tty: fix up atime/mtime mess, take four This problem was taken care of three times already in * b0de59b5733d18b0d1974a060860a8b5c1b36a2e (TTY: do not update atime/mtime on read/write), * 37b7f3c76595e23257f61bd80b223de8658617ee (TTY: fix atime/mtime regression), and * b0b885657b6c8ef63a46bc9299b2a7715d19acde (tty: fix up atime/mtime mess, take three) But it still misses one point. As John Paul correctly points out, we do not care about setting date. If somebody ever changes wall time backwards (by mistake for example), tty timestamps are never updated until the original wall time passes. So check the absolute difference of times and if it large than "8 seconds or so", always update the time. That means we will update immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the check, but it was always that way. Thanks John for serving me this so nicely debugged. Signed-off-by: Jiri Slaby Reported-by: John Paul Perry Cc: # all, as b0b885657 was backported Acked-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- drivers/tty/tty_io.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c index 51f066aa375e..2bb4dfc02873 100644 --- a/drivers/tty/tty_io.c +++ b/drivers/tty/tty_io.c @@ -1028,8 +1028,8 @@ EXPORT_SYMBOL(start_tty); /* We limit tty time update visibility to every 8 seconds or so. */ static void tty_update_time(struct timespec *time) { - unsigned long sec = get_seconds() & ~7; - if ((long)(sec - time->tv_sec) > 0) + unsigned long sec = get_seconds(); + if (abs(sec - time->tv_sec) & ~7) time->tv_sec = sec; } -- cgit v1.2.3-59-g8ed1b From 30a22c215a0007603ffc08021f2e8b64018517dd Mon Sep 17 00:00:00 2001 From: Peter Hurley Date: Sun, 1 Mar 2015 10:11:05 -0500 Subject: console: Fix console name size mismatch commit 6ae9200f2cab7 ("enlarge console.name") increased the storage for the console name to 16 bytes, but not the corresponding struct console_cmdline::name storage. Console names longer than 8 bytes cause read beyond end-of-string and failure to match console; I'm not sure if there are other unexpected consequences. Cc: # 2.6.22+ Signed-off-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- kernel/printk/console_cmdline.h | 2 +- kernel/printk/printk.c | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/printk/console_cmdline.h b/kernel/printk/console_cmdline.h index cbd69d842341..2ca4a8b5fe57 100644 --- a/kernel/printk/console_cmdline.h +++ b/kernel/printk/console_cmdline.h @@ -3,7 +3,7 @@ struct console_cmdline { - char name[8]; /* Name of the driver */ + char name[16]; /* Name of the driver */ int index; /* Minor dev. to use */ char *options; /* Options for the driver */ #ifdef CONFIG_A11Y_BRAILLE_CONSOLE diff --git a/kernel/printk/printk.c b/kernel/printk/printk.c index 01cfd69c54c6..bb0635bd74f2 100644 --- a/kernel/printk/printk.c +++ b/kernel/printk/printk.c @@ -2464,6 +2464,7 @@ void register_console(struct console *newcon) for (i = 0, c = console_cmdline; i < MAX_CMDLINECONSOLES && c->name[0]; i++, c++) { + BUILD_BUG_ON(sizeof(c->name) != sizeof(newcon->name)); if (strcmp(c->name, newcon->name) != 0) continue; if (newcon->index >= 0 && -- cgit v1.2.3-59-g8ed1b From c4e6dcfa00dab9b10e75bba835393b81f256310b Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Mon, 16 Feb 2015 22:39:04 +0800 Subject: serial: sprd: Fix missing spin_unlock in sprd_handle_irq() Fix return from sprd_handle_irq() with spin_lock held. Signed-off-by: Axel Lin Reviewed-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/sprd_serial.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c index 594b63331ef4..bca975f5093b 100644 --- a/drivers/tty/serial/sprd_serial.c +++ b/drivers/tty/serial/sprd_serial.c @@ -293,8 +293,10 @@ static irqreturn_t sprd_handle_irq(int irq, void *dev_id) ims = serial_in(port, SPRD_IMSR); - if (!ims) + if (!ims) { + spin_unlock(&port->lock); return IRQ_NONE; + } serial_out(port, SPRD_ICLR, ~0); -- cgit v1.2.3-59-g8ed1b From 2bb785169e9709d41220e5c18b0270883a82f85c Mon Sep 17 00:00:00 2001 From: Peter Hurley Date: Sun, 1 Mar 2015 10:18:16 -0500 Subject: serial: core: Fix iotype userspace breakage commit 3ffb1a8193bea ("serial: core: Add big-endian iotype") re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can assign the port iotype (which is expected to match the selected i/o accessors), so iotype values must not be changed. Cc: Kevin Cernekee Cc: # 3.19+ Signed-off-by: Peter Hurley Reviewed-by: Kevin Cernekee Signed-off-by: Greg Kroah-Hartman --- include/linux/serial_core.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index baf3e1d08416..1094f2d9cadb 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -147,9 +147,9 @@ struct uart_port { #define UPIO_HUB6 (1) /* Hub6 ISA card */ #define UPIO_MEM (2) /* 8b MMIO access */ #define UPIO_MEM32 (3) /* 32b little endian */ -#define UPIO_MEM32BE (4) /* 32b big endian */ -#define UPIO_AU (5) /* Au1x00 and RT288x type IO */ -#define UPIO_TSI (6) /* Tsi108/109 type IO */ +#define UPIO_AU (4) /* Au1x00 and RT288x type IO */ +#define UPIO_TSI (5) /* Tsi108/109 type IO */ +#define UPIO_MEM32BE (6) /* 32b big endian */ unsigned int read_status_mask; /* driver specific */ unsigned int ignore_status_mask; /* driver specific */ -- cgit v1.2.3-59-g8ed1b From 647f162b8e7e446c4bade031eb8a1a0a83d3de82 Mon Sep 17 00:00:00 2001 From: Peter Hurley Date: Sun, 1 Mar 2015 10:24:28 -0500 Subject: serial: uapi: Declare all userspace-visible io types ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype. UART drivers use the UPIO_* definitions, but the uapi header defines parallel values and userspace uses these parallel values for ioctls; thus the userspace values are definitive. Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*; extend the uapi defines to include all values in use by the serial core. Signed-off-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- include/linux/serial_core.h | 14 +++++++------- include/uapi/linux/serial.h | 4 ++++ 2 files changed, 11 insertions(+), 7 deletions(-) diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index 1094f2d9cadb..d10965f0d8a4 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -143,13 +143,13 @@ struct uart_port { unsigned char iotype; /* io access style */ unsigned char unused1; -#define UPIO_PORT (0) /* 8b I/O port access */ -#define UPIO_HUB6 (1) /* Hub6 ISA card */ -#define UPIO_MEM (2) /* 8b MMIO access */ -#define UPIO_MEM32 (3) /* 32b little endian */ -#define UPIO_AU (4) /* Au1x00 and RT288x type IO */ -#define UPIO_TSI (5) /* Tsi108/109 type IO */ -#define UPIO_MEM32BE (6) /* 32b big endian */ +#define UPIO_PORT (SERIAL_IO_PORT) /* 8b I/O port access */ +#define UPIO_HUB6 (SERIAL_IO_HUB6) /* Hub6 ISA card */ +#define UPIO_MEM (SERIAL_IO_MEM) /* 8b MMIO access */ +#define UPIO_MEM32 (SERIAL_IO_MEM32) /* 32b little endian */ +#define UPIO_AU (SERIAL_IO_AU) /* Au1x00 and RT288x type IO */ +#define UPIO_TSI (SERIAL_IO_TSI) /* Tsi108/109 type IO */ +#define UPIO_MEM32BE (SERIAL_IO_MEM32BE) /* 32b big endian */ unsigned int read_status_mask; /* driver specific */ unsigned int ignore_status_mask; /* driver specific */ diff --git a/include/uapi/linux/serial.h b/include/uapi/linux/serial.h index 5e0d0ed61cf3..25331f9faa76 100644 --- a/include/uapi/linux/serial.h +++ b/include/uapi/linux/serial.h @@ -65,6 +65,10 @@ struct serial_struct { #define SERIAL_IO_PORT 0 #define SERIAL_IO_HUB6 1 #define SERIAL_IO_MEM 2 +#define SERIAL_IO_MEM32 3 +#define SERIAL_IO_AU 4 +#define SERIAL_IO_TSI 5 +#define SERIAL_IO_MEM32BE 6 #define UART_CLEAR_FIFO 0x01 #define UART_USE_FIFO 0x02 -- cgit v1.2.3-59-g8ed1b From 2c3fbe3cf28fbd7001545a92a83b4f8acfd9fa36 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 4 Mar 2015 10:39:03 +0100 Subject: net: irda: fix wait_until_sent poll timeout In case an infinite timeout (0) is requested, the irda wait_until_sent implementation would use a zero poll timeout rather than the default 200ms. Note that wait_until_sent is currently never called with a 0-timeout argument due to a bug in tty_wait_until_sent. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable # v2.6.12 Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- net/irda/ircomm/ircomm_tty.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/net/irda/ircomm/ircomm_tty.c b/net/irda/ircomm/ircomm_tty.c index 40695b9751c1..4efe486baee6 100644 --- a/net/irda/ircomm/ircomm_tty.c +++ b/net/irda/ircomm/ircomm_tty.c @@ -798,7 +798,9 @@ static void ircomm_tty_wait_until_sent(struct tty_struct *tty, int timeout) orig_jiffies = jiffies; /* Set poll time to 200 ms */ - poll_time = IRDA_MIN(timeout, msecs_to_jiffies(200)); + poll_time = msecs_to_jiffies(200); + if (timeout) + poll_time = min_t(unsigned long, timeout, poll_time); spin_lock_irqsave(&self->spinlock, flags); while (self->tx_skb && self->tx_skb->len) { -- cgit v1.2.3-59-g8ed1b From 6b270fd4db08fc13683d616a733d9cacdd3b4afa Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 4 Mar 2015 10:39:04 +0100 Subject: TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation Remove incorrect and redundant wait_until_sent operation, which waits for the driver buffer rather than any hardware buffers to drain, something which is already taken care of by the tty layer (and chars_in_buffer). Signed-off-by: Johan Hovold Reviewed-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- drivers/tty/bfin_jtag_comm.c | 13 ------------- 1 file changed, 13 deletions(-) diff --git a/drivers/tty/bfin_jtag_comm.c b/drivers/tty/bfin_jtag_comm.c index d7b198c400c7..ce24182f8514 100644 --- a/drivers/tty/bfin_jtag_comm.c +++ b/drivers/tty/bfin_jtag_comm.c @@ -210,18 +210,6 @@ bfin_jc_chars_in_buffer(struct tty_struct *tty) return circ_cnt(&bfin_jc_write_buf); } -static void -bfin_jc_wait_until_sent(struct tty_struct *tty, int timeout) -{ - unsigned long expire = jiffies + timeout; - while (!circ_empty(&bfin_jc_write_buf)) { - if (signal_pending(current)) - break; - if (time_after(jiffies, expire)) - break; - } -} - static const struct tty_operations bfin_jc_ops = { .open = bfin_jc_open, .close = bfin_jc_close, @@ -230,7 +218,6 @@ static const struct tty_operations bfin_jc_ops = { .flush_chars = bfin_jc_flush_chars, .write_room = bfin_jc_write_room, .chars_in_buffer = bfin_jc_chars_in_buffer, - .wait_until_sent = bfin_jc_wait_until_sent, }; static int __init bfin_jc_init(void) -- cgit v1.2.3-59-g8ed1b From f528bf4f57e43d1af4b2a5c97f09e43e0338c105 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 4 Mar 2015 10:39:05 +0100 Subject: USB: serial: fix infinite wait_until_sent timeout Make sure to handle an infinite timeout (0). Note that wait_until_sent is currently never called with a 0-timeout argument due to a bug in tty_wait_until_sent. Fixes: dcf010503966 ("USB: serial: add generic wait_until_sent implementation") Cc: stable # v3.10 Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/generic.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c index ccf1df7c4b80..54e170dd3dad 100644 --- a/drivers/usb/serial/generic.c +++ b/drivers/usb/serial/generic.c @@ -258,7 +258,8 @@ void usb_serial_generic_wait_until_sent(struct tty_struct *tty, long timeout) * character or at least one jiffy. */ period = max_t(unsigned long, (10 * HZ / bps), 1); - period = min_t(unsigned long, period, timeout); + if (timeout) + period = min_t(unsigned long, period, timeout); dev_dbg(&port->dev, "%s - timeout = %u ms, period = %u ms\n", __func__, jiffies_to_msecs(timeout), @@ -268,7 +269,7 @@ void usb_serial_generic_wait_until_sent(struct tty_struct *tty, long timeout) schedule_timeout_interruptible(period); if (signal_pending(current)) break; - if (time_after(jiffies, expire)) + if (timeout && time_after(jiffies, expire)) break; } } -- cgit v1.2.3-59-g8ed1b From 79fbf4a550ed6a22e1ae1516113e6c7fa5d56a53 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 4 Mar 2015 10:39:06 +0100 Subject: TTY: fix tty_wait_until_sent on 64-bit machines Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an infinite timeout (0) would be passed to the underlying tty-driver's wait_until_sent-operation as a negative timeout (-1), causing it to return immediately. This manifests itself for example as tcdrain() returning immediately, drivers not honouring the drain flags when setting terminal attributes, or even dropped data on close as a requested infinite closing-wait timeout would be ignored. The first symptom was reported by Asier LLANO who noted that tcdrain() returned prematurely when using the ftdi_sio usb-serial driver. Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the underlying tty driver. Note that the serial-core wait_until_sent-implementation is not affected by this bug due to a lucky chance (comparison to an unsigned maximum timeout), and neither is the cyclades one that had an explicit check for negative timeouts, but all other tty drivers appear to be affected. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable # v2.6.12 Reported-by: ZIV-Asier Llano Palacios Signed-off-by: Johan Hovold Reviewed-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- drivers/tty/tty_ioctl.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-) diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c index a5cf253b2544..89ae23ac9ae6 100644 --- a/drivers/tty/tty_ioctl.c +++ b/drivers/tty/tty_ioctl.c @@ -217,11 +217,17 @@ void tty_wait_until_sent(struct tty_struct *tty, long timeout) #endif if (!timeout) timeout = MAX_SCHEDULE_TIMEOUT; + if (wait_event_interruptible_timeout(tty->write_wait, - !tty_chars_in_buffer(tty), timeout) >= 0) { - if (tty->ops->wait_until_sent) - tty->ops->wait_until_sent(tty, timeout); + !tty_chars_in_buffer(tty), timeout) < 0) { + return; } + + if (timeout == MAX_SCHEDULE_TIMEOUT) + timeout = 0; + + if (tty->ops->wait_until_sent) + tty->ops->wait_until_sent(tty, timeout); } EXPORT_SYMBOL(tty_wait_until_sent); -- cgit v1.2.3-59-g8ed1b From c37bc682e30b8027054356214eb8a3aafbda8e37 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 4 Mar 2015 10:39:07 +0100 Subject: TTY: fix tty_wait_until_sent maximum timeout Currently tty_wait_until_sent may take up to twice as long as the requested timeout while waiting for driver and hardware buffers to drain. Fix this by taking the remaining number of jiffies after waiting for driver buffers to drain into account so that the timeout actually becomes a maximum timeout as it is documented to be. Note that this specifically implies tighter timings when closing a port as a consequence of actually honouring the port closing-wait setting for drivers relying on tty_wait_until_sent_from_close (e.g. via tty_port_close_start). Signed-off-by: Johan Hovold Reviewed-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- drivers/tty/tty_ioctl.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c index 89ae23ac9ae6..632fc8152061 100644 --- a/drivers/tty/tty_ioctl.c +++ b/drivers/tty/tty_ioctl.c @@ -218,10 +218,10 @@ void tty_wait_until_sent(struct tty_struct *tty, long timeout) if (!timeout) timeout = MAX_SCHEDULE_TIMEOUT; - if (wait_event_interruptible_timeout(tty->write_wait, - !tty_chars_in_buffer(tty), timeout) < 0) { + timeout = wait_event_interruptible_timeout(tty->write_wait, + !tty_chars_in_buffer(tty), timeout); + if (timeout <= 0) return; - } if (timeout == MAX_SCHEDULE_TIMEOUT) timeout = 0; -- cgit v1.2.3-59-g8ed1b From 1711fd9addf214823b993468567cab1f8254fc51 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 7 Mar 2015 21:08:46 +0000 Subject: sunrpc: fix braino in ->poll() POLL_OUT isn't what callers of ->poll() are expecting to see; it's actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap bit... Signed-off-by: Al Viro Cc: stable@vger.kernel.org Cc: Bruce Fields Signed-off-by: Linus Torvalds --- net/sunrpc/cache.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/sunrpc/cache.c b/net/sunrpc/cache.c index 33fb105d4352..5199bb1a017e 100644 --- a/net/sunrpc/cache.c +++ b/net/sunrpc/cache.c @@ -921,7 +921,7 @@ static unsigned int cache_poll(struct file *filp, poll_table *wait, poll_wait(filp, &queue_wait, wait); /* alway allow write */ - mask = POLL_OUT | POLLWRNORM; + mask = POLLOUT | POLLWRNORM; if (!rp) return mask; -- cgit v1.2.3-59-g8ed1b From 9eccca0843205f87c00404b663188b88eb248051 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sun, 8 Mar 2015 16:09:09 -0700 Subject: Linux 4.0-rc3 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index e6a9b1b94656..1100ff3c77e3 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 4 PATCHLEVEL = 0 SUBLEVEL = 0 -EXTRAVERSION = -rc2 +EXTRAVERSION = -rc3 NAME = Hurr durr I'ma sheep # *DOCUMENTATION* -- cgit v1.2.3-59-g8ed1b